Miniature Regulator Series ARJ310

Transcription

1 Miniature Regulator Series 30 Compact and lightweight (Main body 65 g) 8.3 Improved flow characteristics Allows smaller mounting pitch 8.8mm 0-M Inlet pressure: MPa Accommodates two types of threads Inside: Female thread (M5 x 0.8) Outside: Male thread (/8) AR45 V VEX ARX0 VY T AP G 4 Panel mounting type Built-in One-touch fitting ø4, ø6 (Metric size) ø5/3", ø/4" (Inch size) 457

2 Miniature Regulator Series 30 Standard Specifications Pressure gauge port size Fluid Proof pressure Maximum operating pressure Regulating pressure range Ambient and operating temperature range Mass Rc /8, NPT /8 (Female thread) Air. MPa 0.8 MPa Standard: 0. to MPa, Low pressure use (0. MPa setting): 5 to 0. MPa 5 to 60 C (No freezing) Approx. 65 g JIS Symbol Port size N0 R/8, M5 x 0.8 NPT/8, M5 x 0.8 Rc /8 NPT /8 30F-0-04 ø4 One-touch fitting R/8, M5 x F-0-06 ø6 One-touch fitting 30F-N0-03 ø5/3" One-touch fitting NPT/8, M5 x F-N0-07 ø/4" One-touch fitting M5 x 0.8 female thread is cut inside the pipe. (Option) Part No. Thread type N R, Rc NPT Body size 0 Relieving type Pressure gauge Note) G5-0-0(Rc/8)/G5-P0-N0(NPT/8) Note) Pressure gauges (G5) for 0. MPa are not available. How to Order With One-touch fitting 3 0 F 0 BG With One-touch fitting Port size () /8 (Male thread), M5 x 0.8 (Female thread) B G Port size (, ) 0 None Pressure gauge BG Note ) For products with pressure gauge, pressure gauge is shipped together with product. /8 (Male thread), M5 x 0.8 (Female thread) /8 (Female thread) Option S MPa setting (Standard) 0. MPa setting Note ) With seal Applicable tubing O.D. () Metric size 04 4 mm mm Inch size /3" /4" 30F-N0 Made to Order Refer to page 460 for details. Note ) Compared with standard specifications, its adjusting spring has been only changed for 0. MPa. It is not the product which does not allow the pressure more than 0. MPa. Adjusting spring is not replaceable. Besides, in the case with the pressure gauge, the pressure gauge will be the one for MPa.

3 Miniature Regulator Series 30 Flow Characteristics (Representative Values) Inlet pressure: MPa F F Pressure Characteristics (Representative Values) Construction Inlet pressure (MPa) Set point Conditions: Inlet pressure MPa Outlet pressure 0. MPa Flow rate Q = 0 l/min (ANR) F30F-0 Component Parts No Description Body Valve guide Bonnet Piston Valve Adjusting screw Panel nut Hexagon nut Adjusting spring Valve spring Spring holder Mini Y-seal O-ring Lock washer Pressure gauge Cassette Material Aluminum alloy POM Steel wire Stainless steel Steel band NBR NBR SS Steel band POM, Stainless steel Note Electroless nickel plated Electroless nickel plated Rubber lining material: HNBR Zinc chromated Zinc chromated Electrophoretic painting 459 AR45 V VEX ARX0 VY T AP00

4 Series 30 Dimensions F M x Panel cutout dimensions ø.5/panel thickness: 4 or less x ø5.5 Port size Rc, NPT /8 Applicable tubing O.D. Metric size ø4, ø6 Inch size ø5/3", ø/4" (Width across flats) 6 Pressure gauge port size Rc, NPT /8 M5 x 0.8 (Female thread) 8.3 R, NPT/ Made to Order Specifications Consult with SMC for detailed dimensions, specifications and delivery. For middle pressure (MPa Setting): Compared with standard specifications, its adjusting spring has been only changed for MPa. It is not the product which does not allow the pressure more than MPa. Adjusting spring is not replaceable Relieving type Body size Port size (.) /8 (Male thread), M5 x 0.8 (Female thread) /8 (Female thread) How to Order B X04 N Thread type R, Rc NPT B None Option S Made to Order X04 MPa Setting (For middle pressure) MPa setting (Standard) 0. MPa setting Note) With seal Note ) Compared with standard specifications, its adjusting spring has been only changed for MPa. It is not the product which does not allow the pressure more than MPa. Adjusting spring is not replaceable.

5 Series 30 Specific Product Precautions Be sure to read before handling. Refer to front matters 4 and 43 for Safety Instructions and pages 87 to 9 for Precautions on every series. Warning Design and Selection. This product cannot be used as a check regulator by installing it between solenoid valve and actuator. It can result in causing breakdown and malfunction.. When piping, tighten the regulator with the recommended proper tightening torque (M5:.5 to N m, R /8: 7 to 9 N m) while holding the wrench flats (width ) of the valve guide for port and holding the hexagonal section of the body for the port. Excessive tightening or holding a part other than those specified can cause damage. 3. While piping to products or operating the handle, ensure that an excess bending moment should not be applied to a product, because it may result in damage. Caution Mounting To set the correct pressure. Make connections after confirming the mark which indicates the air inlet. Reversed connections can cause malfunction. AR45 V VEX ARX0 VY T AP00 46