Dominator 2 Parts & Specifications

Transcription

1 Manual Part # Dominator 2 Parts & Specifications Revised: January 19, 2016 IOWA MOLD TOOLING CO., INC. PO Box 189 Garner, IA Tel: FAX: Website: Copyright 2016 Iowa Mold Tooling Co., Inc. All rights reserved No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of Iowa Mold Tooling Co., Inc. Iowa Mold Tooling Co., Inc. is an Oshkosh Corporation Company. Printed on 19 January, 2016

2

3 i Contents Revisions... iv Parts Ordering Information 7 Specifications 9 Dominator Chassis Specifications Assemblies & Installation 13 Body Installation ( ) Body Assembly ( ) Body Installation ( ) (Repl. by ) Body Components Door Assembly ( ) Door Latch Installation ( ) PTO Wiring Installation-2006 to Present ( ) PTO Wiring Installation Through 2005 ( ) PTO/Pump Rotation Guide ( ) Crane Installation Hole Pattern ( ) Hydraulic Installation ( ) (Eff ) Hydraulic Reservoir ( ) (Eff ) Hydraulic Installation ( ) (Thru ) Hydraulic Reservoir ( ) (Thru ) Reference, Hyd. Reservoir Plumbing ( ) (Thru 2006) Installation Kit, Compartment Pressure Fan Option ( ) Compressor Mounting Locations ( ) Weather-Strip Installation ( ) Battery Cover Installation ( ) Electric Crane Installation (2003i, 3203i, 4004i, 5005i, 6006i) ( ) Electrical Installation (1015E & 2020E) ( ) Compartment Options 63 Compartment Layout ( ) Parts List, Shelves ( ) Installation Drawing, Shelves ( ) Installation Drawing, Door Trays ( ) Parts List, Drawer Units and Kits Dominator I & II Drawer Set Reference Drawing Drawer Components Compartment Options Tool Box Tray ( ) Tank Bracket, 2-Bottle ( ) Tank Bracket, 3-Bottle ( ) Pull-Out Bin Sets... 77

4 ii Contents Tailgate & Bumper Options 79 Tailgate Assembly ( ) Bumper Hitch & Workbench Options Air System Options 83 Air Tank Options Air Tank Kit, 22.5 Gallon ( ) Air Tank Kit, 15 Gal ( ) Air Tank Kit, Dual 15 Gal ( ) Air Tank Kit, 35 Gallon ( ) Air Tank Kit, 58 Gallon ( ) Stepless Ear Clamp Installation ( ) Moisture Separator / Regulator / Oiler Assembly ( ) Moisture Separator / Regulator / Oiler Parts ( ) Moisture Separator / Regulator / Oiler Installation Hose Reel ( ) Telescoping Tops 99 Telescopic Top Installation ( ) Tethered Lid Assembly ( ) Boom Supports 103 Boom Support ( ) Boom Support, Adjustable, 1015 & 2020 ( ) Boom Support, Adjustable, ( ) Stabilizers 109 Front Stabilizers ( / ) Rear Stabilizers, Manual Out / Manual Down ( / )(Eff. 3/29/13) Rear Stabilizers, Manual Out / Manual Down ( / )(Through 3/28/13) Rear Stabilizers, Manual Out/Power Down ( / ) Rear Stabilizers, Power Out/Power Down ( / )(Eff. 3/29/13) Rear Stabilizers, Power Out/Power Down ( / )(Through 3/28/13) Stabilizer Hydraulic Installation ( ) Cylinder, Power Out (3B142860) (Effective 2-07, prior to 8-05) Cylinder, Power Out ( ) (Used 9-05 to 1-07) Stabilizer Assembly ( ) Stabilizer Assembly, Stationary Mount ( ) Cylinder ( ) (Thru. 9-05, Eff. 2/07) Cylinder ( ) (Eff through 1/07) Valvebank, Power Out/Power Down ( ) (Eff ) Valvebank, Power Out/Power Down ( ) (Through ) Valvebank, Manual Out/Power Down ( ) (Eff ) Valvebank, Manual Out/Power Down ( ) (Through ) Stabilizer Override Installation & Operation ( )

5 Contents iii Electrical Options & Installation 141 Electrical Installation ( ) (Eff ) Electrical Installation ( ) (Eff thru ) Electrical Installation ( ) (Through ) Electrical Panel ( ) Chassis Electrical Installation ( ) (Eff ) Power Panel (Dom 1-2) ( ) Power Panel Harness (Dom 4) ( ) Fuse Block, EFM, & Relay Bracket Installation ( ) (Thru ) Crane Installation Comparison Light Installation ( ) By-Pass Procedure for Reverse Activated Floodlights Electrical Outlet ( ) Light Reel Kits Miscellaneous Options 165 Salvage / Plumbing Installation Kit ( ) Salvage Tank Installation, Welder in Load Bed ( ) Salvage Pump Assembly ( ) (Eff. 6-08) Antifreeze/Salvage/Water Pump ( ) (Eff ) Salvage Pump Assembly ( /Dwg ) (Thru 5-08) Headache Rack Parts & Installation ( ) Master Lock System Drawing ( ) Master Lock Kits Fuel Fill, Chevy/GMC ( ) Welder Platforms 181 Welder Deck, 24" Long with 2 Underbody Toolboxes ( ) Welder Deck, 35" Long with 2 Underbody Toolboxes ( ) Welder Deck, 36" Long with Flat Deck ( ) Welder Deck, 24" Long with Tall Compartment ( ) Welder Deck, 35" Long with Curbside Tall Compartment ( ) Welder Deck, 35" Long with Streetside Tall Compartment ( ) Dominator Decal Examples & Placement 189 Decal List Dominator and Crane Logo Placement Body Safety Decal Placement Dominator Control Decal Placement Crane Safety Decal Placement on Dominator Door Hydraulic Oil Decal Placement Fuel Tank Decal Placement Air Tank Decal Placement Stabilizer Decal Placement Reflector & Hitch Decal Placement Compressor Decal Placement

6 iv Contents Revisions DATE LOCATION DESCRIPTION VARIOUS ECN 9754, BOM AUDIT AND CHANGES TO , , , , ECN ADDED RELAY FOR E-BRAKE ECN ADDED DIODE TO PTO LIGHT GROUND, CHANGED BOM QUANTITIES AND ADDED ITEMS ADDED DECAL PLACEMENT PHOTOS ADDED NEW DOM SII HOLE INDEX PATTERN ECN CHANGE IN HARDWARE, ADDED MOUNTING LOCATIONS, EDITED INSTALLATION DRAWING , , ECNs 9756, 9760, CHANGES TO STABILIZER HARDWARE, ADDITIONAL NOTES ON STABILIZER DRAWINGS ECN CHANGE TO HOSE LENGTHS ON , ECN ADDED KITS FOR MASTER LOCK COMPONENTS ECN ADDED NOTE ABOUT 10" MINIMUM BETWEEN COOLER AND COMPRESSOR ECN ADDED WIRING FOR AUTO. TRANSMISSION ECN NEW OPTION - TELESCOPING TOP BODY COMPONENTS ECN HARDWARE KIT PART NUMBER WAS STABILIZER S ECN CYLINDER CHANGE. CYLINDER REPLACED 3B142860; CYLINDER REPLACED STABILIZER ASSEMBLIES , UPDATED WITH NEW CYLINDERS. ECN CHANGED HOSE ROUTING, FITTINGS ECN ADDED FUEL FILL, GMC/CHEVY ( ) TO MISCELLANEOUS SECTION , ECN VERTICAL HYD TANK. ADDED TANK ASSEMBLY, INSTALL DWG, BODY INSTALL DWG ECN ADDED 9' OPTION , ECN REVERT TO ZINC HARDWARE , , ECN CHANGED STAB HOSE ROUTING, ADDED FITTING ADDED DOOR ASSEMBLY DRAWING ECN HARDWARE KIT CHANGE ON STABILIZER ASM ECN ADDED WELDMENTS, INSTALLATION DRAWING FOR UNITS WITH WELDER IN LOAD BED ECN ADDED NOTE REGARDING FILTERS, HARDWARE FOR SHIPOUT BODIES ECN CRANE INSTALLATION DRAWING CHANGE ECN REMOVED MID-MOUNT REQUIREMENT; ECN UPDATE TO WASHER HARDWARE ECN CHANGE DRAKE TO NYLOC NUTS ON INSTALLATION KIT , ECN 10041, REPL WITH ; REPL WITH ECN CHANGED SHELF INSTALLATION PARTS, ECN 10065

7 Contents v , ECN IMPROVED ASSEMBLY ECN REMOVED SHIMS; (ECN 9000) - ADDED HOLE LOCATION FOR FLOOR WITHOUT WELDER CUTOUT ECN ADDED HINGES TO TELE TOP DRAWING ECN LENGTHENED THREADED ROD ON RESERVOIR , ECN HARDWARE CHANGE ON ; NEW CAP SCREW ON KEY CYLINDER ECN 9899 ADDED KEY CYLINDER REPLACEMENT INFORMATION TO BODY ASSEMBLY INFORMATION ECN WASHER CHANGE , ECN ADDED DOM 4 PARTS TO LIST , , , , , ADDED PORT TUBE OPTION TO STABILIZER ASSEMBLIES ECN CHANGE TO HARDWARE KIT , CYLINDER CHANGE ECN ADDED NEW ELEC INSTALLATION DWG ECN CHANGED DIVIDER IN , ECN STANDARDIZED MOUNTING HOLE LOCATIONS ADDED HORIZONTAL TRAY ASSEMBLY DRAWING - TO COMPARTMENT SECTION ECN UPDATE TELE TOP HARDWARE , , , Compartment Options ECN CHANGED HARDWARE ON STABILIZER & BOOM SUPPORT KITS ECN ADDED TERMINAL & SEAL TO PARTS LIST; ECN NEW ELEC INSTALLATION Added drawer set and individual drawer drawings. ( , , , , sets; 13", 26", 39" wide drawer components.) ECN Added information to reservoir drawing. (Not exported) ECN Changed light from to ECN Changed bolts in from to Update BOM ECN Added 2006& 2007 chassis wiring Corrected incorrect part number Added notes to drawing ECN Added CAS2545 compressor to installation WELDER DECKS NEW DRAWINGS , , , , , , ECN Cylinder replacement , ROLLOUT ECN Added parts drawings for all rollout drawers. DRAWERS ECN 10397, New stabilizer valves. New drawings , ECN New weatherstrip installation drawing. Notes on changed to reflect new weatherstrip ECN NEW STAB OVERRIDE.

8 vi Contents , 26, 39 Drawer components , , Pull- Updated drawings with purchased part numbers only. ECN Clamp was Added pump rotation guide. ECN Electrical dome light was , now Corrected cabinet part number on Pull-Out Bin Sets. Out Bin Sets ECN Added #17 locking pin Master lock kits ECN Standardized master lock hardware kits for 9', 11', and 13-14' bodies Added note to vise mounting bracket ECN Changed master lock installation. Also updated bracket information on Corrected part numbers for 56" tall divider panel Added FLR installation drawing. Specifications Added chassis specifications Replace salvage/antifreeze pump asm with correct asm , Add part descriptions on door parts list, changed drawing to rev. A on , ECN Added stepless ear clamp install instructions, added hydraulic installation drawing , ECN Updated #17 in , added salvage pump asm ECN Battery relocation instructions ECN Updates to telescoping top ECN Changed to single inlet hydraulic pumps , ECN New hydraulic reservoir assembly, installation drawing Added version of hydraulic reservoir installation Added replacement lock set information , Added electric crane installation drawings ECN Compressor spacing requirements. Added summary drawings to replace individual drawer and drawer set drawings ,9990 ECN Changed stabilizer manual override decal to , Decal list Added dual battery wiring information Decals ECN Updated decal views and added welding caution decal ECN Electrical installation update Added power panel harness drawing ECN Update to PO/PD stabilizer assembly ECN Drawing correction. ECN Update to decals, stabilizer verbiage , ECN Updated cylinder drawings. 3B Parts list update per engineering mark-up ECN added new drawings Effective 3/29/ Door Assembly photo missing CAP SCR.25-20X 1.00 HH GR5Z CN231-ADDED 8 TETHERED LID ASSEMBLY CN197-Added Door Latch Installation w/o backing plate Replaced missing images

9 7 C HAPTER 1 Parts Ordering Information GENERAL This remainder of this manual contains the exploded parts drawings and accompanying parts lists for the assemblies used on this body. For equipment such as cranes, compressors, and winches, refer to the appropriate service manual. BODY IDENTIFICATION Every IMT body has an identification placard (see figure). This placard is attached in the upper left hand corner of the left vertical 1 compartment. LR LH LV2 LV1 SERIAL TAG LOCATION Dominator Body Layout RH RV2 RV1

10 8 Dominator 2 Parts & Specifications Manual Part # When ordering parts, communicating warranty information, or referring to the unit in correspondence, always include the serial number and model numbers. Address all inquiries to your authorized IMT distributor or to: Iowa Mold Tooling Co., Inc. Box 189, Garner, IA Telephone: Technical Support Fax: IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA MODEL NUMBER SERIAL NUMBER MFG DATE PARTS IDENTIFICATION To insure proper replacement parts are received, specify the complete number/letter sequence for any part requested. The parts sections of this manual can assist you in determining the correct part number. ORDERING REPAIR PARTS When ordering replacement parts: 1 Give the model number of the unit. 2 Give the serial number of the unit. 3 Specify the complete part number. When ordering cylinder parts, or one of the main weldments, always give the stamped part number. 4 Give a complete description of the part. 5 Specify the quantity required. 6 Fill in your serial number to assist in future replacement parts ordering. DOMINATOR SERIAL NUMBER:

11 9 C HAPTER 2 Specifications SPECIFICATIONS 11-foot 13-foot 14-foot Body Rating 60,000 ft-lb 60,000 ft-lb 60,000 ft-lb Body Weight 3,650 lb to 3,875 lb (Based on configuration) 4,005 lb 4,180 lb to 4,310 lb (Based on configuration) Body Width (including rain eaves) 96 in 96 in 96 in Sidepack Height 52 in 52 in 52 in Sidepack Depth 22 in 22 in 22 in Cargo Deck Width 50 in 50 in 50 in Workbench Depth 24 in 24 in 24 in Tailgate Height 10 in 10 in 10 in Storage Capacity (including workbench) ft³ to ft³ (Based on configuration) ft³ ft³ to ft³ (Based on configuration) Angle of Departure Door Opening Dimensions - 52" High Sidepacks LH 1st Vertical 29.5 W x 46.5 H 29.5 W x 46.5 H 29.5 W x 46.5 H LH 2nd Vertical 16.5 W x 46.5 H 18.0 W x 46.5 H 29.5 W x 46.5 H LH 3rd Vertical N/A 16.5 W x 46.5 H 16.5 W x 46.5 H LH Horizontal 44.5 W x 21.0 H 44.5 W x 21.0 H 44.5 W x 21.0 H LH Rear 18.0 W x 46.5 H 18.0 W x 46.5 H 18.0 W x 46.5 H RH 1st Vertical 29.5 W x 46.5 H 29.5 W x 46.5 H 29.5 W x 46.5 H RH 2nd Vertical 16.5 W x 46.5 H 18.0 W x 46.5 H 29.5 W x 46.5 H RH 3rd Vertical N/A 16.5 W x 46.5 H 16.5 W x 46.5 H RH Horizontal 44.5 W x 21.0 H 44.5 W x 21.0 H 44.5 W x 21.0 H RH Rear 18.0 W x 46.5 H 18.0 W x 46.5 H 18.0 W x 46.5 H

12 10 Dominator 2 Parts & Specifications Manual Part # Standard Configurations 11-foot body 52" standard left-hand and right-hand sidepacks Right front raised* to 60" Right front and left front raised* to 60" Right front raised* to 60"; All left side compartments raised to 60" 13-foot body Right front raised* to 60" 14-foot body Right front and left front raised* to 60" Right front raised* to 60"; All left side compartments raised to 60". * Includes 1st and 2nd vertical compartments. NOTE: Crane box is 52" high for all configurations. Body Materials The sidepacks are constructed of 10-gauge and 12-gauge galvannealed steel. The floor structure is constructed of 10-gauge galvannealed and 1/8 deckplate steel. The workbench is constructed of galvannealed and cold rolled steel. Body Weights 11 ft RH & LH standard 3,650 lb 11 ft RF raised 3,700 lb 11 ft RF & LF raised 3,750 lb 11 ft RF raised / LH all raised 3,825 lb 11 ft RH & LH all raised 3,875 lb 13 ft RF raised 4,005 lb 14 ft RF & LF raised 4,180 lb 14 ft RF raised / LH all raised 4,310 lb Body Sub-Structure Patent pending inverted A-frame design constructed of 10-gauge galvannealed material with integral crane box, front stabilizer receptacles and rear stabilizer housing. Electrical System The electrical system consists of a central power distribution point in the crane box using automotive-style harnesses. The circuits use white wire with the circuit function printed every 3. The harness is protected by an overbraid that is heat and cut resistant. Doors The doors are constructed of 14-gauge galvannealed steel with internal formed eaves and hemmed edges. The latches are a 3-point, locking rotary T-handle style. They are constructed of cast steel with a powder-coat finish. The hinges are stainless steel with composite washers. Storage Capacity 11ft RH & LH standard ft³ 11 ft RF raised ft³ 11 ft RF & LF raised ft³ 11 ft RF raised / LH all raised ft³ 11 ft RH & LH all raised ft³ 13 ft RF raised ft³ 14 ft RF & LF raised ft³ 14 ft RF raised / LH all raised ft³ Options 1. Drawers and drawer sets 6. Individual incandescent compartment lights 2. Standard adjustable shelves 7. Work lights 3. 3" high divided adjustable shelves 8. Compartment pressurization system 4. Manual and hydraulic stabilizers 9. Air systems 5. Workbench vises and vise plates 10. Telescopic cranes up to 60,000 ft-lb

13 Chapter 2 Specifications 11 Dominator Chassis Specifications CHASSIS SPECIFICATIONS Minimum Cab-to-Axle Dimensions (Cab-to-Trunnion for tandem axle) Dominator I & II without Welder Single Axle (CA) Tandem Axle (CT) Deck 9' Body 60" 11' Body 84" 13' Body 108" 14' Body 120" Dominator I & II with Welder Single Axle (CA) (based on width Tandem Axle (CT) Deck of welder deck selected) 9' Body 84" - 96" 11' Body 108" - 120" 13' Body 132" - 144" 14' Body 144" - 156" Dominator IV without Welder Single Axle (CA) Deck 14' Body 120" 19' Body 150" Dominator IV with Welder Deck Single Axle (CA) (based on width of welder deck selected) 14' Body 144" - 156" Tandem Axle (CT) 19' Body 174" - 186" Tandem Axle (CT) (based on width of welder deck selected)

14

15 13 C HAPTER 3 Assemblies & Installation In This Chapter Body Installation ( ) Body Assembly ( ) Body Installation ( ) (Repl. by ) Body Components Door Assembly ( ) PTO Wiring Installation-2006 to Present ( ) PTO Wiring Installation Through 2005 ( ) PTO/Pump Rotation Guide ( ) Crane Installation Hole Pattern ( ) Hydraulic Installation ( ) (Eff ) Hydraulic Reservoir ( ) (Eff ) Hydraulic Installation ( ) (Thru ) Hydraulic Reservoir ( ) (Thru ) Reference, Hyd. Reservoir Plumbing ( ) (Thru 2006) Installation Kit, Compartment Pressure Fan Option ( ) Compressor Mounting Locations ( ) Weather-Strip Installation ( ) Battery Cover Installation ( ) Electric Crane Installation (2003i, 3203i, 4004i, 5005i, 6006i) ( ) Electrical Installation (1015E & 2020E) ( )... 61

16 14 Dominator 2 Parts & Specifications Manual Part # Body Installation ( ) NOTE: DRAWING ; KIT REPLACED DRAWING ; KIT REPLACED EFFECTIVE 12/14/05. 2 X 0.63" PER SIDE THRU FRAMERAIL. POSITION BRACKET AS FAR FORWARD AS POSSIBLE WHILE ALIGNING WITH THE 3.0" HOLE SPACING IN THE BODY MOUNT RAIL. CHASSIS FRAME 3.69" 2 X 0.63" PER SIDE 5.2" THRU FRAMERAIL 6.0" 7.0" DOM 2: 49.16" 14' DOM 4: 56.0" 19' DOM 4: 86.0" BODY-SEE NOTE #1 1 3,7 7,8 NOTES: 3,7 SEE NOTE #2 FRONT-GRADE 5 TORQUE TO 115 FT-LB 7,8 2,6 MUDFLAPS TO FRONT OF REAR COMPARTMENT (COMPARTMENT NOW SHOWN) 9 4,5 7,8 3,7 BODY TO CHASSIS SEE NOTE #2 REAR - GRADE 8 TORQUE TO 160 FT-LB 1 RIGHT AND LEFT SIDE PACKS OMITTED FOR CLARITY. 2 FASTENERS CAN BE INSTALLED FROM EITHER DIRECTION. TORQUE TO 160 FT-LB. 3 WHEN TORQUING, HOLD THE BOLT AND APPLY TORQUE TO THE NUT WITH THE TORQUE WRENCH.

17 Chapter 3 Assemblies & Installation PARTS LIST ITEM PART # DESCRIPTION QUANTITY MOUNTING ANGLE-BODY TIE DOWN CAP SCR.31-18X 1.25 HH GR5 Z CAP SCR.62-11X 2.00 HH GR8 Z (WAS 14) NUT HEX NYLOCK WASHER.31 BONDED PLTD (WAS ) WASHER.31X1.50 OD ZINC WASHER.62 FLAT ASTM F436 (WAS 28) NUT HEX ZINC NYLOK GR8 (WAS 14) MUD FLAP W/IMT LOGO 16H X 24W 2 REV. B

18 16 Dominator 2 Parts & Specifications Manual Part # Body Assembly ( ) 15 APPLY WEATHERSTRIP TO DOOR WITHOUT LATCH CRANE SIDE ONLY 16 7 (2 PLCS) /8" HOLE APPLY TREAD DECAL FLUSH TO BOTTOM & OUTSIDE EDGE OF SIDEPACK DETAIL A SCALE 1/4 RH SIDEPACK SHOWN. LH ASSEMBLY IS SIMILAR. DOOR JAM WEATHERSHIP APPLIED TO BODY (SEE NOTE): (DOM I 9' BODY) (DOM I 11' BODY) (DOM II 11' BODY) (DOM II 13' BODY) (DOM II 14' BODY) (DOM IV 14' BODY) (DOM IV 19' BODY) 2 ROD ATTACHMENT HARDWARE INCLUDED WITH LATCH NOTE: WEATHERSTRIP WAS CHANGED EFFECTIVE THE OLD WEATHERSTRIP IS AVAILABLE FOR SERVICE. CHECK THE DOOR BRACE FOR A 1/8" HOLE TO DETERMINE WHICH WEATHERSTRIP PART NUMBER YOUR BODY REQUIRES. MODEL WEATHERSTRIP PART # FOR DOORS WITHOUT 1/8" HOLE IN BRACE (PRIOR TO ) DOMINATOR I 9' DOMINATOR I 11' DOMINATOR II 11' DOMINATOR II 13' DOMINATOR II 14' DOMINATOR IV ' DOMINATOR IV 19' WEATHERSTRIP PART # FOR DOORS WITH 1/8" HOLE IN BRACE (AS SHOWN IN DRAWING) (POST )

19 Chapter 3 Assemblies & Installation (10 PLCS) BODY ASSEMBLY PARTS LIST ( ) ITEM PART # DESCRIPTION QUANTITY LATCH ASM-3PT COMPRESSION A/R 2. VARIOUS ROD-DOOR A/R HANDLE-BODY BOLT ON 7.0X2.5BLK STEP GRIP STRUT LH (WAS ) CAP SCR-SS.31-18X1.00 TRH PHH STEP GRIP STRUT RH (WAS ) CAP SCR-THD CUT.31-18X.75 HWH1 (WAS ) WASHER-SS.31 R FLAT WRT TYPE (WAS 6) NUT-SS HEX NYLOC FENDER RUBBER (DOM 2,3) FENDER RUBBER (DOM 1) FENDER RUBBER (DOM 4-14') FENDER RUBBER (DOM 4-19') RIVET-AL LG HD.25X.50 GRIP A/R PLUG-PLSTC BUTTON BP-1-1/8 A/R TREAD-SHUR STEP 12"X 21 in WEATHERSTRIP-.75X.38 TRIM-LOC X119 BT A/R EDGING-PLASTIC BLK A/R DRIP TRAY (DOM 1 & 2) DRIP TRAY (DOM 4) 1 REV. F NOTE: FEATURES SHOWN ARE NOT AVAILABLE ON ALL MODELS. CHECK SPECIFICATIONS OR WITH YOUR IMT DISTRIBUTOR FOR MORE INFORMATION. See Dominator Chassis Specifications (on page 11) for CA and CT dimensions.

20 18 Dominator 2 Parts & Specifications Manual Part # Body Installation ( ) (Repl. by ) NOTE: DRAWING ; KIT REPLACED BY DRAWING ; KIT EFFECTIVE 12/14/05. B 8,9,10,11 7 5, DETAIL B 6,13 SCALE 0.16:1 NOTES: 1 Install tie rods and plates with washers and single nuts on each end. 2 Tighten tie rods evenly, alternating top to bottom and left to right, until torque value of 45 ft-lb is reached. 3 After final torquing of all tie rods, add jam nut to each end of tie rod to prevent nut loosening.

21 Chapter 3 Assemblies & Installation 19 A 12, 13 12,13,14 (2) DETAIL A: SCALE 3/16:1 13, 14 LEFT & RIGHT SIDEPACKS OMITTED FOR CLARITY (TYP 2) 49.16" 33.0" 7.0" 2.51" NOTES: 1 Rear fasteners can enter from either direction. 2 Torque value = 160 ft-lb 3 When using torque wrench, hold bolt and apply torque to nut. 5.20" 0.69" (3) THRU FRAMERAILS

22 20 Dominator 2 Parts & Specifications Manual Part # PARTS LIST ITEM PART # DESCRIPTION QUANTITY 1. N/A BODY WELDMENT FRONT MTG SIDE SHIFT STRAP ROD-THREADED X CLAMP PLATE-.50X2.50X NUT HEX MUD FLAP W/IMT LOGO 16H X 24W WASHER-SS.31X1.50 OD WASHER-SS.31 FLAT CAP SCR-SS.31-18X 1.00 HH NUT-SS HEX NYLOC CAP SCR.62-11X 2.50 HH GR8 Z WASHER.62 FLAT ASTM F NUT HEX NYLOCK 6 REF INSTALLATION KIT- BODY-CHASSIS REV. B Body Components Body Description Body Weldment Part # DOMINATOR 2-11' RIGHT RAISED COMPARTMENTS 1-2/ LEFT STANDARD DOMINATOR 2-11' RIGHT STANDARD / LEFT STANDARD DOMINATOR 2-11' RIGHT RAISED COMPARTMENTS 1-2/ LEFT RAISED COMPARTMENTS DOMINATOR 2-11' RIGHT 60" HIGH / LEFT 60" HIGH DOMINATOR 2-11' RIGHT RAISED COMPARTMENTS 1-2/ LEFT 60"HIGH DOMINATOR 2-13' RIGHT RAISED COMPARTMENTS 1-2/ LEFT STD DOMINATOR 2-14' RIGHT RAISED COMPARTMENTS 1-2/ LEFT RAISED COMPARTMENTS DOMINATOR 2-14' RIGHT RAISED COMPARTMENTS 1-2/ LEFT 60"HIGH Component Component Description Part # BASE - BODY ASSEMBLY DRAWING ROD-DOOR LG W/0.75 OFFSET ROD-DOOR LG W/0.75 OFFSET ROD-DOOR LG W/.75" OFFSET ROD-DOOR LG W/.75" OFFSET PLUG-PLSTC BUTTON BP / LATCH ASM-3PT COMPRESSION

23 Chapter 3 Assemblies & Installation 21 Component Component Description Part # WEATHERSTRIP-128' ROLL.62X WEATHERSTRIP-148' ROLL.62X WEATHERSTRIP-158' ROLL.62X WEATHERSTRIP-.75X TRIM-LOC X119 BT EDGING-PLASTIC BLK DECAL KIT-OUTSIDE MANUAL KIT -DOM 2 & DOM 2 LO/PRO KIT HRDW DOM CRANE DRIP TRAY KIT-HRDW DOM RIVET/GRAB HANDLE (D2-3) (WAS ) INSTALLATION KIT BODY CHASSIS REV REV KEY CYLINDER REPLACEMENT: The Dominator service vehicle uses door latch assembly on all compartment doors. Upon installation, the latch assemblies have a common key cylinder, part number However, the key cylinders can be changed so compartments use different keys. This feature allows different Dominator compartments to have different keys, thus increasing security. Part # , Cylinder / Key Tool for Compression Latch, is required to change the key cylinders on the Dominators. Alternate key cylinders include: Cylinder/Key Compression Latch J Cylinder/Key Compression Latch J Cylinder/Key Compression Latch J Cylinder/Key Compression Latch J Cylinder/Key Compression Latch J Cylinder/Key Compression Latch J Cylinder/Key Compression Latch J Cylinder/Key Compression Latch J Cylinder/Key Compression Latch J Cylinder/Key Compression Latch J210

24 22 Dominator 2 Parts & Specifications Manual Part # Door Assembly ( ) A DETAIL A 4 14 NOTES: 1. Three per hinge. 2. One per hinge. 3. Before Assembly-Apply Loc-Tite 515 around each hole. 4. Four per hinge. ITEM LOCATION BODY 52" DOM 2 60" DOM 2 1. LEFT VERT 1 ALL LEFT VERT 2 11' LEFT VERT 2 13' LEFT VERT 2 14' LEFT VERT 3 13' & 14' LEFT HORIZ W/LATCH 11', 13', 14' LEFT HORIZ W/LATCH 9' N/A N/A 5. LEFT HORIZ W/O LATCH 11', 13', 14' LEFT HORIZ W/O LATCH 9' N/A N/A 6. LEFT REAR ALL RIGHT VERT 1 ALL RIGHT VERT 2 11' RIGHT VERT 2 13' RIGHT VERT 2 14' RIGHT VERT 3 13' & 14'

25 Chapter 3 Assemblies & Installation 23 ITEM LOCATION BODY 52" DOM 2 60" DOM RIGHT HORIZ W/LATCH 11', 13', 14' RIGHT HORIZ W/LATCH 9' N/A N/A 11. RIGHT HORIZ W/O LATCH 11', 13', 14' RIGHT HORIZ W/O LATCH 9' N/A N/A 12. RIGHT REAR ALL N/A 13. WORKBENCH ALL SCREW-MACH.25-20X.75 ALL TRHTORXSS (4 PER HINGE) 15. NUT-SS NYLOC (3 ALL PER HINGE) 16. WELD NUT (1 PER ALL HINGE) 17. HINGE-SS 10GA BUTT ALL REV

26 24 Dominator 2 Parts & Specifications Manual Part # Door Latch Installation ( ) SHOWN FOR REFERENCES Note: This image shows the current Door Latch Installation without the backing plate. For replacement door latch, use IMT Part Number,

27 Chapter 3 Assemblies & Installation 25 PTO Wiring Installation-2006 to Present ( ) Allison T1000/T2000 TCM with Single PTO (4th Generation) (2006-present) ( ) IGNITION 12V TO PTO GROUND SPLICE ( ) CHASSIS ELEC. INSTALL. INSTR. 1,2 3 3 PTO 5 E-BRAKE 80-PIN CONNECTOR ON T.C.M. WIRE 43 (143) GM (143) WIRE 50 (150) GM (104) NOTE: 1 Different chassis may have different codes for the TCM wire numbers. 2 TCM for Freightliner is behind the dash on the passenger side of the cab. Splice into appropriate wires at that location. 3 TCM for Sterling Actera is located under the cab. Use customer access Metripack connector located on the driver's side wheel well. Use cavity "F" for pin 43 and cavity "G" for pin 50. Use item #5 terminal to connect. 4 TCM for International 4300 and 4400 models is located under the cab. Use customer access Metripack connector located in the driver's side, upper wheel well. Use cavity "B" for wire 43 and cavity "C" for wire 50. Use item #5 terminal to connect and newer GM Transmission Connector (Located near upfitter connector in the engine compartment on the right side) Wire 143 = Pin C; Wire 104 = Pin K. ALLISON T1000/T2000 4th GEN SINGLE PTO WIRING PARTS LIST ITEM PART # DESCRIPTION QUANTITY FUSE HOLDER W/O FUSE FUSE-ATC 7.5 AMP RELAY TERMINAL, MP GA MALE DIODE SWITCH-ROCKER 1 NEW

28 26 Dominator 2 Parts & Specifications Manual Part # Allison T1000/T2000 TCM with Dual PTO (4th Generation) (2006-present) ( ) COMPRESSOR SWITCH TO PTO GROUND SPLICE (REF CHASSIS ELEC. INSTL. INSTRUCTIONS) 4 PTO SOLENOID IGNITION 12 V 6 CRANE SWITCH COMP RELAY PTO CMPRSR PTO 1, E-BRAKE 80-PIN CONNECTOR ON T.C.M. WIRE 43 (143) GM (143) WIRE 50 (150) GM (104) 3 4 CRANE RELAY PTO CRANE PTO NOTE: 1 Different chassis may have different codes for the TCM wire numbers. 2 TCM for Freightliner is behind the dash on the passenger side of the cab. Splice into appropriate wires at that location. 3 TCM for Sterling Actera is located under the cab. Use customer access Metripack connector located on the driver's side wheel well. Use cavity "F" for pin 43 and cavity "G" for pin 50. Use item #5 terminal to connect. 4 TCM for International 4300 and 4400 models is located under the cab. Use customer access Metripack connector located in the driver's side, upper wheel well. Use cavity "B" for wire 43 and cavity "C" for 50. Use item #5 terminal to connect and newer GM Transmission Connector (Located near upfitter connector in the engine compartment on the right side) Wire 143 = Pin C; Wire 104 = Pin K. ALLISON T1000/T2000 4th GEN DUAL PTO WIRING PARTS LIST ITEM PART # DESCRIPTION QUANTITY FUSE HOLDER W/O FUSE FUSE-ATC 7.5 AMP DIODE AMP/ 274 V RELAY TERMINAL, MP GA MALE SWITCH-ROCKER 2 NEW

29 Chapter 3 Assemblies & Installation 27 Allison T3000/T4000 TCM with Single PTO (4th Generation) (2006-present) ( ) IGNITION 12 V 1, TO PTO GROUND SPLICE (REF CHASSIS ELEC. INSTALL. INSTRUCTIONS) PTO E-BRAKE PIN 45 (145) 3 80 PIN CONNECTOR ON T.C.M. PIN 17 (117) PIN 3 (103) 3 NOTE: 1 Different chassis may have different codes for the TCM wire numbers. 2 TCM for Freightliner is behind the dash on the passenger side of the cab. Splice into appropriate wires at that location and newer GM Transmission Connector (Located near upfitter connector in the engine compartment on the right side) Pin 45 = Pin A; Pin 17 = Pin B; Pin 3 = Pin J ALLISON T3000/T4000 4th GEN SINGLE PTO WIRING PARTS LIST ITEM PART # DESCRIPTION QUANTITY FUSE HOLDER W/O FUSE FUSE-ATC 7.5 AMP RELAY TERMINAL MP GA DIODE AMP/ 274 V SWITCH-ROCKER 1 NEW

30 28 Dominator 2 Parts & Specifications Manual Part # Allison T3000/T4000 TCM with Dual PTO (4th Generation) (2006-present) ( ) COMPRESSOR SWITCH 7 IGNITION 12 V 1,2 4 3 E-BRAKE CRANE SWITCH COMP RELAY TO PTO GROUND SPLICE (REF CHASSIS ELEC. INSTL. INSTRUCTIONS) PTO SOLENOID 4 CMPRSR PTO 3 CRANE RELAY 4 CRANE PTO PIN 45 (145) 80 PIN CONNECTOR ON T.C.M. PIN 17 (117) 4 PIN 3 (103) NOTE: 1 Different chassis may have different codes for the TCM wire numbers. 2 TCM for Freightliner is behind the dash on the passenger side of the cab. Splice into appropriate wires at that location and newer GM Transmission Connector (Located near upfitter connector in the engine compartment on the right side) Pin 45 = Pin A; Pin 17 = Pin B; Pin 3 = Pin J ALLISON T3000/T4000 4th GEN DUAL PTO WIRING PARTS LIST ITEM PART # DESCRIPTION QUANTITY FUSE HOLDER W/O FUSE FUSE-ATC 7.5 AMP DIODE AMP/ 274 V RELAY TERMINAL, MP GA MALE REF SWITCH-ROCKER 2 NEW

31 Chapter 3 Assemblies & Installation 29 Allison T1000/T2000 TCM Freightliner - Single PTO (4th Generation) (2006-present) ( ) TO FREIGHTLINER HARNESS (BACK OF CAB) CONNECTION TO PTO SOLENOID CONNECTOR 200D 151T (PURPLE) GROUND (BLACK) 2 PIN CONNECTOR 1 80-PIN CONNECTOR ON T.C.M. E-BRAKE WIRE 43 (143) WIRE 50 (150) 1 PTO PTO PRESSURE SWITCH PTO ENGAGE (IMT HARNESS) (PURPLE) TO FREIGHTLINER HARNESS (BACK OF CAB) CONNECTION TO PTO PRESSURE SWITCH GROUND (BLACK) 2 PIN CONNECTOR ALLISON T1000/T2000 4th GEN FREIGHTLINER PTO WIRING PARTS LIST ITEM PART # DESCRIPTION QUANTITY RELAY DIODE AMP/ 274 V 2 NEW

32 30 Dominator 2 Parts & Specifications Manual Part # PTO Wiring Installation Through 2005 ( ) Allison T1000/T2000 TCM with Single PTO Through 2005 ( ) IGNITION 12V 1,2 SUPPLIED WITH PTO PTO LAMP PTO PRESS SWITCH 3 SWITCH 3 PTO 5 E-BRAKE GREY CONNECTOR ON TCM WIRE J1-06 WIRE J1-19 NOTE: 1 Different chassis may have different codes for the TCM wire numbers. 2 TCM for Freightliner is behind the dash on the passenger side of the cab. Splice into appropriate wires at that location. 3 TCM for Sterling Actera is located under the cab. Use customer access Metripack connector located on the driver's side wheel well. Use cavity "F" for wire J1-06 and cavity "G" for wire J1-19. Use item #4 terminal to connect. 4 TCM for International 4300 and 4400 models is located under the cab. Use customer access Metripack connector located in the driver's side, upper wheel well. Use cavity "B" for wire J1-06 and cavity "C" for J1-19. Use item #4 terminal to connect. 5 GM Transmission Connector (Located near upfitter connector in the engine compartment on the right side) Wire 106 = Pin B; Wire 119 = Pin J ALLISON T1000/T2000 SINGLE PTO WIRING PARTS LIST ITEM PART # DESCRIPTION QUANTITY FUSE HOLDER W/O FUSE FUSE-ATC 7.5 AMP RELAY TERMINAL, MP GA MALE DIODE, 2.2 AMP 1 REV. B

33 Chapter 3 Assemblies & Installation 31 Allison T1000/T2000 TCM with Dual PTO Through 2005 ( ) IGNITION 12V 1,2 4 3 E-BRAKE GREY CONNECTOR ON TCM SUPPLIED WITH PTO WIRE J1-06 WIRE J1-19 COMP. PTO LAMP COMPRESS SWITCH CRANE PTO LAMP CRANE SWITCH COMP RELAY 3 4 CRANE RELAY 4 PTO SOLENOID PTO COMPRESSOR PTO PTO CRANE PTO PTO PRESS SWITCH PTO PRESS SWITCH NOTE: 1 Different chassis may have different codes for the TCM wire numbers. 2 TCM for Freightliner is behind the dash on the passenger side of the cab. Splice into appropriate wires at that location. 3 TCM for Sterling Actera is located under the cab. Use customer access Metripack connector located on the driver's side wheel well. Use cavity "F" for wire J1-06 and cavity "G" for wire J1-19. Use item #5 terminal to connect. 4 TCM for International 4300 and 4400 models is located under the cab. Use customer access Metripack connector located in the driver's side, upper wheel well. Use cavity "B" for wire J1-06 and cavity "C" for J1-19. Use item #4 terminal to connect. 5 GM Transmission Connector (Located near upfitter connector in the engine compartment on the right side) Wire 106 = Pin B; Wire 119 = Pin J ALLISON T1000/T2000 DUAL PTO WIRING PARTS LIST ITEM PART # DESCRIPTION QUANTITY FUSE HOLDER W/O FUSE FUSE-ATC 7.5 AMP DIODE AMP RELAY TERMINAL, MP GA MALE 2 REV. B

34 32 Dominator 2 Parts & Specifications Manual Part # Allison T3000/T4000 TCM with Single PTO Through 2005 ( ) IGNITION 12V SUPPLIED WITH PTO 1,2 3 PTO LAMP PTO PRESSURE SWITCH 5 E-BRAKE SWITCH PTO PTO 3 PIN 2 GRAY CONNECTOR ON TCM PIN 30 PIN 31 3 NOTE: 1 Different chassis may have different codes for the TCM wire numbers. 2 TCM for Freightliner is behind the dash on the passenger side of the cab. Splice into appropriate wires at that location. 3 GM transmission connector (located near the GM upfitter connector in the engine compartment on the right side); Pin 2 = Pin A, Pin 30 = Pin B, Pin 31 = Pin J ALLISON T3000/T4000 SINGLE PTO WIRING PARTS LIST ITEM PART # DESCRIPTION QUANTITY FUSE HOLDER W/O FUSE FUSE-ATC 7.5 AMP RELAY TERMINAL, MP GA MALE 3 REV. B

35 Chapter 3 Assemblies & Installation 33 Allison T3000/T4000 TCM with Dual PTO Through 2005 ( ) IGNITION 12V 1,2 4 3 E-BRAKE SUPPLIED WITH PTO COMP. PTO LAMP COMPRESS SWITCH CRANE PTO LAMP CRANE SWITCH COMP RELAY CRANE RELAY 3 4 PTO SOLENOID 4 PTO COMPRESSOR PTO PTO CRANE PTO PTO PRESS SWITCH PTO PRESS SWITCH PIN 2 GREY CONNECTOR ON TCM PIN 30 4 PIN 31 NOTE: 1 Different chassis may have different codes for the TCM wire numbers. 2 TCM for Freightliner is behind the dash on the passenger side of the cab. Splice into appropriate wires at that location. 3 GM transmission connector (located near the GM upfitter connector in the engine compartment on the right side); Pin 2 = Pin A, Pin 30 = Pin B, Pin 31 = Pin J 4 Use item #5 to connect. ALLISON T3000/T4000 DUAL PTO WIRING PARTS LIST ITEM PART # DESCRIPTION QUANTITY FUSE HOLDER W/O FUSE FUSE-ATC 7.5 AMP DIODE 2.2 AMP RELAY TERMINAL, MP GA MALE REF REV. B

36 34 Dominator 2 Parts & Specifications Manual Part # Allison T1000/T2000 TCM with Single PTO on Freightliner with PTO Dash Switch Through 2005 ( ) TO FREIGHTLINER HARNESS (BACK OF CAB) CONNECTION TO PTO SOLENOID CONNECTOR 200D 151T (PURPLE) GROUND (BLACK) 2 PIN CONNECTOR 1 E-BRAKE WIRE J1-06 WIRE J PTO PTO ENGAGE (IMT HARNESS) 2 PTO PRESSURE SWITCH (PURPLE) TO FREIGHTLINER HARNESS (BACK OF CAB) CONNECTION TO PTO PRESSURE SWITCH GROUND (BLACK) 2 PIN CONNECTOR GREY CONNECTOR ON TCM ALLISON T1000/T2000 TCM SINGLE PTO ON FREIGHTLINER WITH PTO DASH SWITCH ITEM PART # DESCRIPTION QUANTITY RELAY DIODE, 2.2 AMP 2 REV. B

37 Chapter 3 Assemblies & Installation 35 PTO/Pump Rotation Guide ( ) IF THE WIRE BETWEEN THE POWER MODULE (#5) AND THE BATTERY IS LONGER THAN 24" INSTALL PARTS #19 AND #20 IN-LINE, AS CLOSE TO THE BATTERY AS POSSIBLE. EXTRA HARDWARE AND BRACKET (#51) ARE SUPPLIED FOR MOUNTING AS NECESSARY. THE RECOMMENDED ORIENTATION OF COMPONENTS IS SHOWN ,3,4 20 5,6,7,8,9 4,11 LEFT POST: PASS THROUGH (FUSED) 12,13, ,13,15 RIGHT POST: SWITCHED THROUGH RELAY (FUSED) 16 USE HEAT SHRINK (#45) OVER THESE CONNECTIONS. NOTES: 1 The pump / driven equipment should always rotate in the opposite direction of the PTO. 2 A geared adapter will always change the rotation of the PTO.

38 36 Dominator 2 Parts & Specifications Manual Part # Crane Installation Hole Pattern ( ) ø0.88 ø0.88 E E 11.50" 14.75" G H J F G HJ F J E J E H J H J G E G E H F H F J J WHEN HOLE "E" IS REQUIRED, THE INDICATED HOLES MUST BE DRILLED THROUGH THE THICK PLATE. HOLE INDEX PER CRANE MODEL: E i 4004i (Models with serial number beginning with 4004i08...) F 2002i (Adapter plate required at installation.) i (Models with 6-digit serial number - Adapter plate required at installation.) G i 6006i H 6020 J 6025 REV. H

39 Chapter 3 Assemblies & Installation 37 Hydraulic Installation ( ) (Eff ) HYD COOLER (CAS3560 ONLY) HOSE "B" OUT TO TANK (CAS3560 ONLY) HOSE "N" FROM COMPRESSOR TO COOLER (CAS3560 ONLY) HOSE "B" RETURN TO TANK (CAS435HA ONLY) CAS3560 SHOWN - SEE NOTES FOR CAS435H DIFFERENCES HOSE "C" CAS3560 ONLY 12 HOSE "A" TO "PRESSURE" INLET OF COMPRESSOR 11 (SUCTION HOSE) HOSE "M" TO "T" ON VALVEBANK ( FROM STABILIZER KIT) 14 HOSE "J" HOSE "H" TO "P" ON VALVEBANK HOSE "L" TO CRANE RETURN SWIVEL HOSE "K" TO "PB" ON VALVEBANK TO CRANE PRESSURE SWIVEL FRONT OF BODY 1 SUCTION SECTION STREET SIDE RETURN SECTION CURB SIDE

40 38 Dominator 2 Parts & Specifications Manual Part # HOSE IDENTIFICATION CHART A COMPRESSOR PRESSURE HOSE B COMPRESSOR TO TANK C COMPRESSOR CASE DRAIN H CRANE PRESSURE J CRANE RETURN TO TANK K CRANE PRESSURE EXT L CRANE TANK EXT M STABILIZER VALVEBANK RETURN (FROM STABILIZER KIT) N COOLER INLET PARTS LIST ITEM PART # DESCRIPTION QUANTITY RESERVOIR ASSEMBLY NIPPLE-PIPE BLK 1.50X CLOSE VALVE-BALL VALVE-BALL FILTER-HYD RET 10MIC 1.25 NPTF ADPTR-MPT/HEX/MPT REDUCER BUSH-STL A/R ADPTR-MPT/M JIC A/R TEE-MALE RUN 1 MPT X 1 JIC A/R 9. SEE CHART HOSEBARB-STRAIGHT SEE CHART CLAMP-HOSE T-BOLT HOSE-HYD R4 A/R HOSE-HYD 1.50 SUCTION A/R ELBOW-MPT/90/M JIC.75 6 A/R VALVE BANK 2 SEC (MAN OUT/HYD DOWN) VALVE BANK 3 SEC (HYD OUT/HYD DOWN) ADPTR-M JIC/M JIC 8 8 (MANUAL STABILIZERS) ADPTR-M STR/M JIC 8 8 (HYD STABILIZERS) ADPTR-M JIC/M JIC (MAN STABILIZERS) TEE-MALE JIC TUBE (HYD STABILIZERS) WASHER.50 FLAT NUT HEX NYLOCK ROD-THREADED X NEW

41 Chapter 3 Assemblies & Installation 39 HYDRAULIC INSTALLATION COMPONENTS - UNITS WITH WELDER DECKS ( ) (EFF ) INSTALLATION KIT HOSE KIT APPLICATION CRANE WITH WELDER DECK CAS435HA COMP. WITH WELDER DECK CAS3560 WITH WELDER DECK CRANE, CAS435HA WITH WELDER DECK CRANE, CAS3560 WITH WELDER DECK A COMP PRESSURE HOSE ASSEMBLY B COMP TANK HOSE ASSEMBLY C COMP CASE DRAIN HOSE ASSEMBLY H CRANE PRESSURE See chart B See chart B See chart B HOSE ASSEMBLY J CRANE RETURN TO TANK HOSE ASSEMBLY See chart B See chart B See chart B K CRANE PRESSURE HOSE ASSEMBLY L CRANE TANK HOSE ASSEMBLY N COOLER INLET HOSE ASSEMBLY 7 REDUCER BUSHING FITTING HOSEBARB STRAIGHT 10 CLAMP-HOSE (2) (2) (2) (2) (2) 12 ELBOW-CASE DRAIN CA COMP AIR FITTING CA COMP AIR FITTING CA COMP AIR FITTING CH COMP HYD FITTING CH COMP HYD FITTING HYDRAULIC INSTALLATION COMPONENTS - UNITS WITHOUT WELDER DECKS ( ) (EFF ) INSTALLATION KIT HOSE KIT A APPLICATION COMP PRESSURE HOSE ASSEMBLY CRANE W/O WELDER DECK CAS435HA W/O WELDER DECK CAS3560 W/O WELDER DECK CRANE, CAS435HA W/O WELDER DECK CRANE, CAS3560 W/O WELDER DECK B C H COMP TANK HOSE ASSEMBLY COMP CASE DRAIN HOSE ASSEMBLY CRANE PRESSURE HOSE ASSEMBLY See chart B See chart B See chart B

42 40 Dominator 2 Parts & Specifications Manual Part # J CRANE RETURN TO TANK HOSE ASSEMBLY See chart B See chart B See chart B K CRANE PRESSURE HOSE ASSEMBLY L CRANE TANK HOSE ASSEMBLY N COOLER INLET HOSE ASSEMBLY 7 REDUCER BUSHING FITTING HOSEBARB STRAIGHT 10 CLAMP-HOSE (2) (2) (2) (2) (2) 12 ELBOW-CASE DRAIN CA COMP AIR FITTING CA COMP AIR FITTING CA COMP AIR FITTING CH COMP HYD FITTING CH COMP HYD FITTING CHART B - PRESSURE & RETURN HOSES, BY BODY LENGTH 11' BODY 11' BODY WITH WELDER DECK 13' & 14' BODY 13' & 14' BODY WITH WELDER DECK H -- CRANE PRESSURE HOSE J -- CRANE RETURN TO TANK HOSE NOTE: QUANTITY SHOWN IN PARENTHESES (). NOT ALL BODY SIZES ARE AVAILABLE FOR ALL MODELS. CHECK THE MODEL SPECIFICATIONS FOR THE APPROPRIATE SIZES.

43 Chapter 3 Assemblies & Installation 41 Hydraulic Reservoir ( ) (Eff ) PARTS LIST 15 ITEM PART # DESCRIPTION QUANTITY SIGHT GAUGE PLUG W/ REFLECTOR PLUG-PIPE MAGNETIC.75NPT SQHD WELDMENT, HYD RESERVOIR ELBOW-STREET STL 1.00 X 90 DEG FILL-BREATHER BAYONET DIFFUSER-INTERNAL 55 GPM 3.00NPT NPT STRAINER-INTERNAL 50 GPM 3.00NPT NPT REDUCER BUSH-BLK NIPPLE-PIPE BLK 1.25X CLOSE REDUCER BUSH-STL ELBOW-STREET STL 1.25 X 90 DEG PLUG-PIPE SQ HD STL.75 1 REV. B

44 42 Dominator 2 Parts & Specifications Manual Part # Hydraulic Installation ( ) (Thru ) HYD. COOLER (CAS3560 ONLY) OUT TO TANK (HOSE "B") HOSE "N" FROM COMPRESSOR TO COOLER (CAS3560 ONLY) IN FROM "T" PORT ON COMPRESSOR (HOSE "N") COMPRESSOR (VIEWED FROM TOP) PORT P (HYD OIL IN) (CAS3560) PORT P (HYD OIL OUT) (CAS3560) PORT IDENTIFICATION HOSE "C" (CAS3560 ONLY) SUCTION HOSE HOSE A CAS435HA: TO "P" CAS3560: TO "HYD OIL IN" HOSE "M" TO "T" ON VALVEBANK ( FROM STABILIZER KIT) HOSE "J" HOSE "H" TO "P" ON VALVE BANK HOSE "B" 9 6 HOSE "L" TO CRANE RETURN SWIVEL HOSE "K" TO "PB" ON VALVEBANK TO CRANE PRESSURE SWIVEL

45 Chapter 3 Assemblies & Installation 43 FRONT OF BODY SUCTION SECTION (STREET SIDE) , RETURN SECTION (CURB SIDE) 16 NOTES: 1 ITEMS 23, 24 ARE REQUIRED FOR 1-1/4" SUCTION LINE. HOSE IDENTIFICATION CHART A COMPRESSOR PRESSURE B COMPRESSOR TANK C COMPRESSOR CASE DRAIN F STRAINER TO PUMP G STRAINER TO PUMP H CRANE PRESSURE J CRANE RETURN TO TANK K CRANE PRESSURE EXT L CRANE TANK EXT M STABILIZER VALVEBANK RETURN (FROM STABILIZER KIT) N COOLER INLET CHART B: CRANE PRESSURE & RETURN TO TANK HOSES 9' BODY 9' WITH WELDER DECK 11' BODY 11' WITH WELDER DECK 13' & 14' BODY 13' & 14' WITH WELDER DECK H J

46 44 Dominator 2 Parts & Specifications Manual Part # PARTS LIST (THRU ) ITEM PART # DESCRIPTION QUANTITY FILTER-HYD RET 10MIC 1.25 NPTF REDUCER BUSH-STL TEE-MALE RUN 1 MPT X 1 JIC VALVE-BALL ADPTR-M STR/M JIC VALVE BANK, 3-SECTION (HYD OUT/HYD DOWN) (WAS ) VALVE BANK, 2-SECTION (MAN OUT/HYD DOWN) (WAS ) TEE-MALE JIC TUBE ELBOW-MPT/90/M JIC ADPTR-MPT/HEX/MPT D(II)- RESERVOIR ASM D1 30 GAL ADPTR-M STR/F JIC SWL ELBOW-M JIC/90/F JIC SW NIPPLE-BARB STL 1.50MPT ADPTR-M STR/M JIC ELBOW-M JIC/90/F SW TUBE ADPTR-M NPT/F JIC SW VALVE-BALL ADPTR-M STR/M JIC CAP SCR.25-20X.62 HH GR5 Z WASHER.25 W FLAT ANSI B27.2Z GUARD-HYD RESERVOIR (WAS ) REDUCER BUSH-STL A/R NIPPLE-BARB STL 1.25MPT 1.50 A/R REV. E

47 Chapter 3 Assemblies & Installation 45 HYDRAULIC INSTALLATION COMPONENTS-UNITS WITH WELDER DECKS ( ) (THRU ) INSTALLATION KIT HOSE KIT A B C F G H J K L N APPLICATION COMP PRESSURE HOSE ASSEMBLY COMP TANK HOSE ASSEMBLY COMP CASE DRAIN HOSE ASSEMBLY STRAINER TO PUMP HOSE STRAINER TO PUMP HOSE CRANE PRESSURE HOSE ASSEMBLY CRANE RETURN TO TANK HOSE ASSEMBLY CRANE PRESSURE HOSE ASSEMBLY CRANE TANK HOSE ASSEMBLY COOLER INLET HOSE ASSEMBLY CRANE WITH WELDER DECK NOT USED (WAS ) See chart B See chart B CAS435HA WITH WELDER DECK (WAS ) NOT USED (WAS CAS3560 WITH WELDER DECK (WAS ) NOT USED (WAS ) CR/CAS435 WITH WELDER DECK D1 FORD AUTO CRANE CAS435HA WITH WELDER DECK (WAS ) NOT USED (WAS See chart B See chart B (WAS ) NOT USED (WAS ) See chart B See chart B REDUCER BUSH REDUCER BUSH FITTING SUCTION TEE 24 ELBOW-RETURN 25 HOSEBARB-STRAIGHT (WAS (WAS ) ) 26 CLAMP (2) (2) (WAS ) CR/CAS WITH WELDER DECK FORD MANUAL (WAS ) NOT USED (WAS ) See chart B See chart B (2) (WAS ) CRANE CAS3560 WITH WELDER DECK (WAS ) NOT USED (WAS NOT USED (WAS ) See chart B See chart B (WAS ) (2) (WAS ) 27 HOSEBARB-ELBOW NOT USED (WAS ) 28 CLAMP (2) (2) (2) NOT USED (WAS ) NOT USED (WAS )

48 46 Dominator 2 Parts & Specifications Manual Part # ELBOW-CASE DRAIN CA COMP AIR FITTING (WAS ) CA COMP AIR FITTING ( ) CA COMP AIR FITTING CH COMP HYD FITTING CH COMP HYD FITTING (WAS ) CH COMP HYD FITTING CH COMP HYD FITTING CH COMP HYD FITTING (WAS ) (WAS ) (WAS (WAS ) ) NOTE: QUANTITY SHOWN IN PARENTHESES (). NOT ALL BODY SIZES ARE AVAILABLE FOR ALL MODELS. CHECK THE MODEL SPECIFICATIONS FOR THE APPROPRIATE SIZES. HYDRAULIC INSTALLATION COMPONENTS-UNITS WITHOUT WELDER DECKS ( ) (THRU ) INSTALLATION KIT HOSE KIT A B C F G H J K APPLICATION COMP PRESSURE HOSE ASSEMBLY COMP TANK HOSE ASSEMBLY COMP CASE DRAIN HOSE ASSEMBLY STRAINER TO PUMP HOSE STRAINER TO PUMP HOSE CRANE PRESSURE HOSE ASSEMBLY CRANE RETURN TO TANK HOSE ASSEMBLY CRANE PRESSURE HOSE ASSEMBLY CRANE WITHOUT WELDER DECK NOT USED (WAS ) See chart B See chart B CAS435HA WITHOUT WELDER DECK (WAS ) NOT USED (WAS ) CAS3560 WITHOUT WELDER DECK (WAS ) NOT USED (WAS ) CR/CAS435 WITHOUT WELDER DECK D1 FORD AUTO CRANE CAS435HA WITHOUT WELDER DECK (WAS ) NOT USED (WAS ) See chart B See chart B (WAS ) NOT USED ( ) See chart B See chart B CR/CAS WITHOUT WELDER DECK FORD MANUAL (WAS ) NOT USED ) See chart B See chart B CRANE CAS3560 WITHOUT WELDER DECK (WAS ) NOT USED (WAS ) NOT USED ( ) See chart B See chart B

49 Chapter 3 Assemblies & Installation 47 L N CRANE TANK HOSE ASSEMBLY COOLER INLET HOSE ASSEMBLY REDUCER BUSH REDUCER BUSH FITTING SUCTION TEE 24 ELBOW-RETURN HOSEBARB-STRAIGHT (WAS (WAS ) ) 26 CLAMP (2) (WAS ) 27 HOSEBARB-ELBOW 28 CLAMP (2) (2) (2) 29 ELBOW-CASE DRAIN CA COMP AIR FITTING (WAS (WAS ) ) CA COMP AIR FITTING ( ) CA COMP AIR FITTING ( 1) CH COMP HYD FITTING CH COMP HYD FITTING CH COMP HYD FITTING CH COMP HYD FITTING CH COMP HYD FITTING (2) (WAS ) (WAS ) (2) (WAS ) (WAS ) (2) (WAS ) NOTE: QUANTITY SHOWN IN PARENTHESES (). NOT ALL BODY SIZES ARE AVAILABLE FOR ALL MODELS. CHECK THE MODEL SPECIFICATIONS FOR APPROPRIATE SIZES. (REV. E )

50 48 Dominator 2 Parts & Specifications Manual Part # Hydraulic Reservoir ( ) (Thru ) FRONT OF BODY PARTS LIST ITEM PART # DESCRIPTION QUANTITY WELDMENT, HYD RESERVOIR ELBOW-STREET STL 1.00 X 90 DEG SIGHT GAUGE PLUG W/REFLCT PLUG-PIPE MAGNETIC.75NPT SQHD FILL-BREATHER BAYONET WASHER.50 FLAT NUT HEX NYLOCK ROD-THREADED X (WAS ) DECAL-MOBILOIL RESERVOIR (NOT SHOWN) 1 REV. E NOTE: IF RESERVOIR IS NOT REQUIRED, USE COVER KIT TO COVER OPENINGS IN FLOOR.

51 Chapter 3 Assemblies & Installation 49 Reference, Hyd. Reservoir Plumbing ( ) (Thru 2006) SUCTION SECTION (STREET SIDE) USE (BLUE) 9 12 LOCKTITE FRONT OF BODY , USE 242 (BLUE) 11 LOCKTITE RETURN SECTION (CURB SIDE) SUCTION ASSEMBLY NOTES: 1 SUB-ASSEMBLE FITTINGS (GROUP 1) AND FITTINGS (GROUP 2). 2 INSTALL GROUP 1 INTO RESERVOIR. 3 ASSEMBLY GROUP 2 ONTO GROUP 1.

52 50 Dominator 2 Parts & Specifications Manual Part # RETURN ASSEMBLY NOTES: 1 SUB-ASSEMBLE GROUPS, DIVIDED AS SHOWN. 2 ASSEMBLE GROUPS TOGETHER. 3 INSTALL ASSEMBLY ONTO RESERVOIR. NOTES: 1 ITEMS #23, 27 NOT USED ON SINGLE INLET PUMPS. REFERENCE, HYD. RESERVOIR PLUMBING ( ) (Thru 2006) ITEM PART # DESCRIPTION QUANTITY RESERVOIR ASSEMBLY GUARD-HYD RESERVOIR NUT-TINNERMAN 1/4-20UNC WASHER.25 FLAT CAP SCR.25-20X.62 HH GR5 Z BLOCK - HYD RESERVOIR NPT ALUMINUM Q O RING 3.62X 3.88X CAP SCR.62-11X 1.50 SH PLAIN STRAINER-INTERNAL 50 GPM 3.00NPT 2.00NPT DIFFUSER-INTERNAL 55 GPM 3.00NPT 2.00NPT REDUCER BUSH-BLK ELBOW-STREET STL 1.50 X 90 DEG ADPTR-MPT/HEX/MPT VALVE-BALL REDUCER BUSH-STL (AS REQUIRED) ADPTR-MPT/HEX/MPT FILTER-HYD RET 10MIC 1.25 NPTF REDUCER BUSH-STL (AS REQUIRED) ADPTR-MPT/M JIC (AS REQUIRED) TEE-MALE RUN 1 MPT X 1 JIC (AS REQUIRED) TEE-STREET STL 1.25 (AS REQUIRED) SEE CHART HOSEBARB-STRAIGHT (AS REQUIRED) CLAMP-HOSE BOLT (AS REQUIRED) SEE CHART HOSEBARB-ELBOW (AS REQUIRED) 1 NOTE: ITEM #20 (FILTER) CAN BE PURCHASED SEPARATELY FROM IMT. ITEMS #18 AND ARE INCLUDED WITH OPTIONAL INSTALLATION KITS. REV B

53 Chapter 3 Assemblies & Installation 51 Installation Kit, Compartment Pressure Fan Option ( ) NOTE - AIR FLOW DIRECTION IS OUT OF CRANE COMPARTMENT 9,10 AS REQ'D 6 WIRE HARNESS CONNECTS TO HARNESS ON BACK OF ELEC. PANEL TERMINATE FAN WIRING WITH ITEMS 7,8 & 11. BLACK WIRE - CAVITY A RED WIRE - CAVITY B 3 (4 PLCS) (4 PLCS) 1 2 NOTE AIR FLOW DIRECTION OUT OF CRANE COMPT 1 4 (4 PLCS) PARTS LIST ITEM PART # DESCRIPTION QUANTITY GUARD-FILTER 12V FAN FAN-12V AXIAL NUT 8-32 HEX NYLOCK SCR-MACH # 8-32X 2.50 RDH GUARD-CHROME WIRE 12V FAN HARNESS-COMPARTMENT FAN TERM-PKRD WPK 18-20GA MALE CONN-PKRD WP 2 CAV MALE/SHROUD RETAINER-ZIP TIE ELEC HARNESS TIES-PLASTIC.18W 8.00L BLACK SEAL-PKRD WP/MP 16 GA GREEN 4

54 52 Dominator 2 Parts & Specifications Manual Part # NEW Compressor Mounting Locations ( ) CAS435HA Compressor Mounting Locations CAS435HA INSTALLATION ON SERIES 1 AND SERIES 2 DOMINATOR 4.40" 13.38" ø0.44" TYP (4) 12.75" 12.00" CAS435HA INSTALLATION ON SERIES 2 DOMINATOR WITH HEADACHE RACK AND STANDARD HEIGHT SIDEPACK ON COMPRESSOR SIDE 4.40" 13.38" ø0.44" TYP (4) 18.75" 12.00" NOTE: When installing a compressor, maintain a minimum clearance of 8" on each end of the compressor. If installing a compressor with a hydraulic aftercooler, maintain a minimum space of 10" between the compressor and aftercooler, while still maintaining the 8" of clearance on each end of the compressor-cooler combination.

55 Chapter 3 Assemblies & Installation 53 CAS2545 & CAS3560 Compressor Mounting Locations CAS3560 & CAS2545 INSTALLATION ON SERIES 1 AND SERIES 2 DOMINATORS CAS3560 & CAS2545 INSTALLATION ON SERIES 2 DOM WITH HEADACHE RACK, STANDARD HEIGHT SIDEPACK ON COMPRESSOR SIDE, AND TELESCOPIC ROOF. 4.38" 12.25" 10.50" 12.00" 12.00" ø0.44" TYP (10) 6.00" 18.00" MIN. 4.38" 12.25" 16.5" 6" 12" 18" MIN. ø0.44" TYP (10) CAS3560 & CAS2545 INSTALLATION ON SERIES 2 DOM WITH HEADACHE RACK AND STANDARD HEIGHT SIDEPACK ON COMPRESSOR SIDE 4.38" 12.25" 16.50" 12.00" 12.00" ø0.44" TYP (10) 6.00" 18.00" MIN. NOTE: When installing a compressor, maintain a minimum clearance of 8" on each end of the compressor. If installing a compressor with a hydraulic aftercooler, maintain a minimum space of 10" between the compressor and aftercooler, while still maintaining the 8" of clearance on each end of the compressor-cooler combination.

56 54 Dominator 2 Parts & Specifications Manual Part # Weather-Strip Installation ( ) WEATHER-STRIP: TOP WILL CAP THE SIDE. GAP BETWEEN WEATHER-STRIP AND DOOR JAM IS ACCEPTABLE. A VIEW A-A WEATHER-STRIP FLUSH WITH DOOR OPENING. B B WEATHER-STRIP BOTTOM IS UNDER THE SIDE.

57 Chapter 3 Assemblies & Installation 55 Battery Cover Installation ( ) 1 2 NOTE: BATTERY COVER NOT SHOWN FOR CLARITY CHASSIS BATTERIES RELOCATED TO COMPARTMENT PARTS LIST ITEM PART # DESCRIPTION KIT # QUANTITY STUD-ELEC PASS THROUGH.38 RED REF STUD-ELEC PASS THROUGH.38 BLK REF HARDWARE KIT-BATTERY COVER BRACKET-BATTERY COVER MOUNT COVER-BATTERY DOM COMPARTMENT LATCH-RUBBER T-HANDLE # CAP SCR.10-24X.50 BTNHD ZC # NUT HEX NYLOCK # WASHER.31 FLAT # NUT HEX NYLOCK # CAP SCR.31-18X.75 HH GR5 Z #3 2 REV. A

58 56 Dominator 2 Parts & Specifications Manual Part # Electric Crane Installation (2003i, 3203i, 4004i, 5005i, 6006i) ( ) Install the IMT 2003i, 3203i, 4004i, 5005i, and 6006i model cranes using the instructions in In addition to meeting the minimum chassis specifications noted in the Technical Data section of this manual, make sure there is sufficient room for mounting the crane and the platform is strong enough to support the crane and rated load. Install the crane only on an IMT designed and approved truck body. The body must be designed to sustain the forces imposed by the crane when lifting the full rated load. Install the body on the chassis before installing the crane. Refer to the following table for parts referenced in the following crane installation drawings. CRANE INSTALLATION PARTS LIST ITEM PART # DESCRIPTION KIT # QUANTITY ELECTRIC CRANE BODY INSTALLATION HARDWARE KIT- 3203i/4004i ELEC CRANE 1 BODY INSTALLATION HARDWARE KIT- 5005i ELEC CRANE BODY 1 INSTALLATION DRAWING-CRANE & WINCH ASSEMBLY 3203I REF 5. Body IMT BODY ASSEMBLY REF BRACKET-SWITCH 300 AMP ELEC CRANE SWITCH-300A KEYED BATTERY DISCONNECT # LEVEL INDICATOR LEVEL # TERMINAL-RING NI.38 STUD 1 WIRE # TERMINAL-RING NI.31 STUD 1-2 WIRE # FUSEHOLDER-HIGH AMP2 BOLT WITH #1 1 COVER FUSE-225 AMP # CABLE-#1 WELDING #1 35 FT TUBE-HEAT SHRINK AMP #1.50 FT CAP SCREW.75-10X 2.50 HH GR8 Z # CAP SCREW X 3.00 HHGR8Z # NUT HEX NYLOC GR8Z # NUT HEX NYLOC GR8Z # WASHER.75 N FLAT H ASTMF436Z # WASHER 1.0 FLAT HI STR # SCR-MACH.25-20X.75 BTNHD ZC #2 & # SCREW-MACHINERY #10-24X.50 RDH #2 & # NUT HEX #2 & # NUT HEX NYLOCK #2 & # WASHER.25 FLAT #2 & #3 8 REV

59 Chapter 3 Assemblies & Installation 57 To install the crane: 1 Use a lifting device capable of lifting the weight of the crane as indicated in the Technical Data section of this manual. Attach fabric slings to the crane lower boom, centered approximately 18 inches (46 cm) from the mast hinge. Make certain the crane is well balanced on the slings by slowly lifting approximately 6" (15 cm) off the ground. Lift the crane and apply a bead of waterproof compound, such as silicon based caulk, to the bottom of the base. Move the chassis under the crane and lower the crane into the desired position. Install the mounting cap screws (item # 15) and washers (item #16) to secure the crane base to the truck body (see figure). Torque the 3/4" cap screws (used on models 3203i and 4004i) to 280 ft-lb and torque to 1" cap screws (used on models 5005i and 6006i) to 680 ft-lb. NOTE: The 3/4-10 x 2.5" grade 8 zinc coated capscrews (models 3203i and 4004i) are designed for a crane box thickness of 1/2" only. The 1-8 x 3" grade 8 zinc coated capscrews (model 5005i and 6006i) are designed for a crane box top thickness of 7/8" to 1" only. A different crane box may require different capscrews. If different length bolts are required, they must be the same size and of sufficient length. Failure to use proper length bolts may cause the bolts to bottom out before torquing. 15, ,17

60 58 Dominator 2 Parts & Specifications Manual Part # MOUNTING PATTERNS ø0.81" 2003i MOUNTING PATTERN 12" 10" 5" 5" 3203i & 4004i MOUNTING PATTERN ø0.81" ø9.5" 6" 5.75" 5005i & 6006i MOUNTING PATTERN 18" 14.75" 7.38" ø1.13" ø6" 6" 6" 4.63" 4.63" 9.25" 12" 18" 14.75" 12" 7.38" 6" 9" 7.38" 14.75" 18" 4.75" 4.75" 9.5" ALLOW 12" RADIUS FOR SWING CLEARANCE ALLOW 16" RADIUS FOR SWING CLEARANCE 11.5" 12" 14" 9" ø13" ALLOW 16" RADIUS FOR SWING CLEARANCE 2 The electrical power switch (item #7) provides power for the crane. Install the switch onto the power unit cover KEY SUPPLIED 6 WITH SWITCH. SPARE 2.75" KEY " 13.5" 3.5" 4 HOLES, 0.266" DIA. LOCATION OF SWITCH BRACKET IN CRANE BOX INSIDE VIEW OF CRANE BOX 3 Install the vehicle level indicator (item #8) parallel to the door reinforcements. 4 After mounting your crane, wire the crane to the vehicle's 12VDC electrical system using the following steps. Use the parts list above to identify parts. Your crane installation kit, , includes a 10.7 m (35') long cable, IMT # (item #13 in the parts list). Use this cable to ground the auxiliary battery, the underhood battery, and to connect the batteries to the fuses and the fuses to the crane on-off switch. Cut the cable to length after determining the lengths required.

61 Chapter 3 Assemblies & Installation 59 5 Ground the crane by connecting the crane ground cable to bare metal inside the crane box. POWER CABLE BRACKET A GROUND CABLE (GROUND TO BARE METAL INSIDE CRANE BOX) 7 MALE POWER CABLE CONNECTOR (#13) ON-OFF SWITCH TO FUSE (CUT TO LENGTH) 6 Connect the crane power cable from the male power cable connector to the on-off power switch. Connect cable (item # ), cut to length, from the crane power switch (item #7) to an electrical bulkhead connector, which will be connected to the fuses in step #8. Use 3/8" (0.95 cm) ring terminals (item # ) for each connection. Heat shrink the connections (item # ). WARNING Protect the power cable from damage by fastening it inside the frame channel and covering it with protective covering including loom, conduit, etc. Be sure to use rubber grommets or other protection when running the power cable through steel bulkheads. 7 Use approximately 4' (1.2 m) of the cable (item #13) to ground both the vehicle battery and auxiliary battery. Connect one end of the ground cable to the negative terminal on the battery, and the other end to bare metal on the truck body. Use a 5/16" (0.79 cm) ring terminal (item # ) to connect to the truck body. WARNING Install the ground cable to the negative terminal of the batteries! The crane electrical ground completes the electrical circuit through the structure of the crane to the vehicle frame. The vehicle factory ground is NOT sufficient to carry the current required by the crane. Without this extra ground cable, your crane may not operate at rated capacity, and motor, contactor, or electrical damage may occur.

62 60 Dominator 2 Parts & Specifications Manual Part # Mount one 225-amp fuse holder (item #11) close to the vehicle battery in a location which can be easily accessed if the fuse needs to be replaced. Repeat with the auxiliary battery. Use approximately one foot (30.5 cm) of cable (item #13) to connect the positive terminals on the vehicle batteries to the fuse holders. Connect the other end of each fuse holder to the bulkhead pass-through connector from step #6, which is then connected to the crane power switch. Cables connect to the fuse holders using 5/16" (0.79 cm) ring terminals (item # ). Heat shrink connections. 10 (-) (+) 1 AUXILIARY BATTERY 13-CABLE # (CUT TO LENGTH) (BATTERY (-) TO CHASSIS GROUND) TO CHASSIS GROUND 13-CABLE # (CUT TO APPROX. 1' (30.5 cm)) (FUSE TO BATTERY (+)) FUSE DETAIL 13-CABLE # (CUT TO LENGTH) BULKHEAD 2 PASS-THROUGH CONNECTOR 13-CABLE # (CUT TO LENGTH) (CRANE ON-OFF SWITCH TO FUSE) FUSE DETAIL (+) 13-CABLE # (CUT TO APPROX. 1' (30.5 cm)) (FUSE TO BATTERY (+)) (-) UNDERHOOD 1 BATTERY FROM ON-OFF SWITCH IN CRANE BOX 10 (5/16" RING TERMINA)L 13-CABLE # (CUT TO LENGTH) TO CRANE NOTES: TO 12 BATTERY (+) (225-AMP 10 (5/16" RING FUSE) 11 TERMINAL) (FUSEHOLDER) 10 TO CHASSIS GROUND 1. Use the highest rating cold-cranking amp battery available up to 1,000 CCA. Underhood and auxiliary batteries must be identical. 2. Use bulkhead pass-through connectors when power or ground passes through a compartment wall. 3. Reference drawing for wiring diagram.

63 Chapter 3 Assemblies & Installation 61 Electrical Installation (1015E & 2020E) ( ) 6 BLACK 2,3,4,5 BROWN NOTE: INSTALL DECAL #1 NEXT TO PARKING BRAKE ACTUATOR ON DASH PANEL. BATTERY PLUG CONNECTION P2 ON VALVEBANK J2 ON CABLE ASSEMBLY 87 IGN V 30 PARKING BRAKE NOTE: SEE APPROPRIATE SPEED CONTROL KIT FOR PARKING BRAKE WIRING. 1 WIRES IN HARNESS ARE 14GA, 19/27 STRANDS, AND MUST MEET FORD SPECIFICATION MIL-85B OR CHRYSLER SPECIFICATION MS PARTS LIST ITEM PART # DESCRIPTION QUANTITY DECAL-CAUTION BRAKE/COMP CAP SCR 1/4-20X1.25 HHGR NUT 1/4-20 HEX NYLOC ZINC WASHER 1/4-FLAT RELAY HARNESS 1 REV. B

64

65 63 C HAPTER 4 Compartment Options In This Chapter Compartment Layout ( ) Parts List, Shelves ( ) Installation Drawing, Shelves ( ) Installation Drawing, Door Trays ( ) Parts List, Drawer Units and Kits Dominator I & II Drawer Set Reference Drawing Drawer Components Compartment Options Tool Box Tray ( ) Tank Bracket, 2-Bottle ( ) Tank Bracket, 3-Bottle ( ) Pull-Out Bin Sets... 76

66 64 Dominator 2 Parts & Specifications Manual Part # Compartment Layout ( ) LR LH LV3 LV2 LV1 SEE PARTS LIST CHART RH RV3 RV2 RV Compartment Key LR Left Rear LH Left Horizontal LV1 Left Vertical 1 LV2 Left Vertical 2 LV3 Left Vertical 3 RH Right Horizontal RV1 Right Vertical 1 RV2 Right Vertical 2 RV3 Right Vertical 3 NOTE: The Left and Right Vertical 3 compartments are only used on Dominator II 13' and 14' bodies COMPARTMENT LAYOUT PARTS LIST ITEM PART # DESCRIPTION QUANTITY 1. SEE CHART SHELF 1 2. SEE CHART SHELF END 1 3. SEE CHART SHELF END NUT HEX NYLOC (WAS ) CAP SCR.31-18X.75 HH (WAS ) WASHER.31 FLAT 18-8 (WAS ) 4 REV H

67 Chapter 4 Compartment Options 65 Parts List, Shelves ( ) COMPARTMENT LOCATION ITEM #3 - SHELF END ITEM #1 - SHELF ITEM #2 - SHELF END SHELF WIDTH (INCHES) SHELF DIVIDER ( ) SHELF KIT NUMBER LEFT VERT INCLUDED LEFT VERT 2-11' INCLUDED LEFT VERT 2-13' INCLUDED LEFT VERT 2-14' INCLUDED LEFT VERT 3-13' INCLUDED LEFT VERT 3-14' INCLUDED LEFT HORIZONTAL 11',13',14' INCLUDED LEFT HORIZONTAL 9' INCLUDED LEFT REAR INCLUDED RIGHT VERT INCLUDED RIGHT VERT INCLUDED RIGHT VERT 2-13' INCLUDED RIGHT VERT 2-14' INCLUDED RIGHT VERT 3-13' INCLUDED RIGHT VERT 3-14' INCLUDED RIGHT HORIZONTAL ',13',14' INCLUDED RIGHT HORIZONTAL 9' INCLUDED DIVIDER PANELS ITEM #3 - SHELF END ITEM #1 - SHELF ITEM #2 - SHELF END SHELF WIDTH (INCHES) SHELF DIVIDER SHELF KIT NUMBER 20" DIVIDER PANEL SHELVES ( ) INCLUDED 40" TALL DIVIDER PANEL

68 66 Dominator 2 Parts & Specifications Manual Part # ( ) (3) (4) " TALL DIVIDER PANEL ( ) REV. M Installation Drawing, Shelves ( ) 1 OR POSITION AND DRILL AT ASSEMBLY PARTS LIST ITEM PART # DESCRIPTION QUANTITY PANEL DIVIDER DOM ADJ SHELF 60"H (WAS ) PANEL DIVIDER DOM ADJ SHELF 44", 52" H 1 (WAS ) PANEL DIVIDER DOM ADJ SHELF 22"H 1 4. SEE CHART SHELF KIT DOM 1.50"H X SEE CHART SHELF KIT DOM 1.50"H X CAP SCR-SS.31-18X 1.00 HH AS REQ'D NUT-SS HEX NYLOC AS REQ'D WASHER-SS-BONDED PLTD.31 AS REQ'D REV. H

69 Chapter 4 Compartment Options 67 Installation Drawing, Door Trays ( ) " TYP " TYP 5 6 3" 7 3" 1 3" 3" 3 3" 38.89" 31.88" 27.63" 26.5" 23.5" " 8.25" TYP 3" 3" A DETAIL A HARDWARE PER TRAY: (4 TYP) (4 TYP) DRILL AT ASSEMBLY. 20.5" 19" 19" NOTE: 1 Position all tray applications 3.0" above latch hole opening. Space all double tray applications 8.25" apart PARTS LIST ITEM PART # KIT # DESCRIPTION QUANTITY TRAY-TORCH DOM W-LATCH REF TRAY-SPRAY CAN DOM W DOOR REF TRAY-TORCH DOM W-LATCH REF TRAY-SPRAY CAN DOM W DOOR REF TRAY-SPRAY CAN DOM W DOOR REF TRAY-SPRAY CAN DOM W DOOR REF TRAY-SPRAY CAN DOM 23.5 W DOOR REF TRAY-SPRAY CAN DOM W DOOR REF TRAY-SPRAY CAN DOM W DOOR REF TRAY-WELDMENT TORCH DOM 19" W/LATCH REF NOTE: Not all trays are available on all models. Check the door widths on your model to determine appropriate options. REV. D

70 68 Dominator 2 Parts & Specifications Manual Part # Parts List, Drawer Units and Kits LR LH LV2 LV1 CHASSIS CAB RH RV2 RV1 Compartment Key LR Left Rear RH Right Horizontal LH Left Horizontal RV3 Right Vertical 3 LV3 Left Vertical 3 RV2 Right Vertical 2 LV2 Left Vertical 2 RV1 Right Vertical 1 LV1 Left Vertical 1 NOTE: The Left and Right Vertical 3 compartments are only used on Dominator II 13' and 14' bodies. The body configuration determines the rollout drawer sets which can be used in each body. COMPARTMENT BODY LENGTH DRAWER SET WIDTH LEFT & RIGHT VERTICAL 1 9', 11', 13', 14' 26" Wide LEFT & RIGHT VERTICAL 2 11' & 13' 13" Wide 14' 26" Wide LEFT & RIGHT VERTICAL 3 13' & 14' 13" Wide LEFT & RIGHT 39" Wide HORIZONTAL LEFT REAR 13" Wide

71 Chapter 4 Compartment Options 69 DRAWER SET WIDTH COMPARTMENT APPLICATION 13" WIDE LEFT & RIGHT VERTICAL 2-11' & 13' BODIES; LEFT & RIGHT VERTICAL 3-13' & 14' BODIES 26" WIDE LEFT & RIGHT VERTICAL 1; LEFT & RIGHT VERTICAL 2-13' & 14' BODIES 39" WIDE LEFT & RIGHT HORIZONTAL COMPARTMENTS PART # 3" HIGH DRAWERS 5" HIGH DRAWERS 7" HIGH DRAWERS " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " DRAWER SET OVERALL HEIGHT

72 70 Dominator 2 Parts & Specifications Manual Part # Dominator I & II Drawer Set Reference Drawing SAMPLE DRAWER SET DRAWING WITH 3", 5", AND 7" HIGH DRAWERS SAMPLE DRAWING WITH 3" DRAWERS ONLY HEIGHT WIDTH RISER HEIGHT 3.0" DEPTH NOTE: 1 Complete drawer set part numbers are included in Parts List, Drawer Units and Kits. 2 The quantity of items 1-5, panels, risers, and shelves, is 1 per drawer set. 3 The quantities of items 6-11, slides and drawers, are based on the number of drawers in the complete kits. ITEM DESCRIPTION 13" SET 26" SET 39" SET 1. PANEL-SIDE, LH REF REF REF 2. PANEL-SIDE, RH REF REF REF 3. RISER

73 Chapter 4 Compartment Options 71 ITEM DESCRIPTION 13" SET 26" SET 39" SET 4. SHELF PANEL-DRAWER BACK REF REF REF 6. DRAWER SLIDE W-TABS LH DRAWER SLIDE W-TABS RH SHELF-ADJUSTABLE END " DRAWER " DRAWER " DRAWER

74 72 Dominator 2 Parts & Specifications Manual Part # Drawer Components SAMPLE DRAWING - DRAWER WITH 4 DIVIDERS 1 (DIVIDER) 4 (LOCK) SAMPLE DRAWING - DRAWER WITH CENTER AND SIDE DIVIDERS 3 (DIVIDER-HEMMED) 1 (DIVIDER) 2 (DIVIDER-CENTER) 4 (LOCK) NOTE: 1 All drawers are painted. 2 Each IMT drawer comes with the standard lock Optional replacement drawer lock sets are available for IMT drawers. Replacement lock sets and can be ordered from IMT customer service. DRAWER PART # DRAWER WITH DIVIDER DIMENSIONS DRAWER COMPONENT PART NUMBERS (QUANTITY IN PARENTHESES) ITEM 1-DIVIDER ITEM 2- DIVIDER, CENTER ITEM 3- DIVIDER, HEMMED " H X 13" W (4) " H X 13" W (4) " H X 13" W (4) " H X 26" W (6) (2) " H X 26" W (6) (2) " H X 26" W (6) (2) " H X 39" W (9) (2) (2) " H X 39" W (9) (2) (2) " H X 39" W (9) (2) (2)

75 Chapter 4 Compartment Options 73 Compartment Options Part # Dimensions / Description Compartments Available Roll-out Tool Box Tray Tray dimensions 32"W x 18.5"D LV1, LV2, RV1, RV2 Oxygen / Acetylene Tank Bracket Tank bracket Oxy/Acet 3 tanks with hook LV1, RV Tank bracket Oxy/Acet 2 tanks with hook (Mounted on front wall in vented compartment) LV1, RV1 Pull-out Drawer Sets drawer set with base 18"D x 8.12"W x 19"H LV1, LV2, LV3, RV1, RV2, RV3, LH, RH, LR drawer set with base 18"D x 8.12"W x 23"H LV1, LV2, LV3, RV1, RV2, RV3, LR bolt drawer set w/base 18"D x 16.25"W x LV1, LV2, LV3, RV1, RV2, RV3, LR 35.5"H bolt drawer set w/base 18"D x 16.25"W x LV1, LV2, LV3, RV1, RV2, RV3, LR 39.5"H drawer set with base 18"D x 8.12"W x 11"H LV1, LV2, LV3, RV1, RV2, RV3, LH, RH, LR Slide-out Parts Book Tray Slide out parts / book tray LH, RH Bookshelf Bookshelf dimensions 8"H x 45"L x 12"D RH, LH Bookshelf dimensions 8"H x 26"L x 12"D RH, LH Note: Left Vertical Compartment 3 (LV3) and Right Vertical Compartment 3 (RV3) are only available on Dominator I and II 13' and 14' models, and may not be available on your model. Check your product specifications.

76 74 Dominator 2 Parts & Specifications Manual Part # Tool Box Tray ( ) 2,5,6,8 1 3,5,6,7 4,5,6,8 9,10, PARTS LIST ITEM PART # DESCRIPTION QUANTITY TRAY 16-3/4 X MTG BRACKET 32" MTG BRACKET DRAWER SLIDE NUT #10-24 LOCK WASHER #10 WRT MACH SCR #10-24 X 5/8 FLHD MACH SCR #10-24 X 5/8 RDHD CAP SCR 5/16-18X3/4 BTNHD WASHER 5/16 WRT NUT 5/16-18 LOCK 4 REV. A

77 Chapter 4 Compartment Options 75 Tank Bracket, 2-Bottle ( ) PARTS LIST ITEM PART # DESCRIPTION QUANTITY HOOK-WLDMT (J) (BOLT IN) BRACKET ACET BOTTLE BRACKET OXY BOTTLE WASHER.25 FLAT (WAS 12) CAP SCR.31-18X.75 HH GR5 Z (WAS 6) NUT HEX NYLOCK STRAP-36" BOTTLE HOLDER W/ SNAP HOOK CHAIN CONNECTOR-THREADED WASHER.31 FLAT CAP SCR x 1.00 HHGR5Z WASHER-BONDED PLATED.31 6 REV C

78 76 Dominator 2 Parts & Specifications Manual Part # Tank Bracket, 3-Bottle ( ) PARTS LIST ITEM PART # DESCRIPTION QUANTITY HOOK-WLDMT (J) (BOLT IN) BRACKET OXY/ACET BOTTLE BRACKET OXY/ACET BOTTLE WASHER.25 FLAT (WAS 10) CAP SCR.31-18X 1.00 HH GR5 Z (WAS 6) NUT HEX NYLOCK (WAS 10) WASHER.31 FLAT STRAP-36" BOTTLE HOLDER W/ SNAP HOOK CHAIN CONNECTOR-THREADED CAP SCR.31-18X.75 HH GR5 Z WASHER-BONDED PLATED.31 8 REV C

79 Chapter 4 Compartment Options 77 Pull-Out Bin Sets Pull-out bins are available for IMT Dominators in sets of 2, 4, 5, 16, and 18 units. BIN SET PARTS LISTS # BINS / QUANTITY ITEM PART # DESCRIPTION 2-BINS ( ) 4-BINS ( ) 5-BINS ( ) 16-BINS ( ) 18-BINS ( ) CABINET (2-BIN SET) CABINET (4-BIN SET) CABINET (5-BIN SET) CABINET (16-BIN SET) CABINET (18-BIN SET) BIN DIVIDER 3.38X SCR-MACH.25-20X BTNHD ZC NUT 1/4-20 LOCK WASHER 1/4 WRT Bin Set with Base ( ) 3 2 ITEMS 4,5,6 NOT SHOWN 1 17" D x 8.13" W x 10.75" H

80 78 Dominator 2 Parts & Specifications Manual Part # Bin Set with Base ( ) 3 5-Bin Set with Base ( ) 3 2 ITEMS 4-7 NOT SHOWN 1 2 ITEMS 4,5,6 NOT SHOWN 1 17" D x 8.13" W x 19" H 16-Bin Set with Base ( ) 17" D x 8.13" W x 23" H 18-Bin Set with Base ( ) ITEMS 4,5,6 NOT SHOWN 1 ITEMS 4,5,6 NOT SHOWN 1 17" D x 16.26" W x 35" H 17" D x 16.26" W x 39" H

81 79 C HAPTER 5 Tailgate & Bumper Options In This Chapter Tailgate Assembly ( ) Bumper Hitch & Workbench Options... 81

82 80 Dominator 2 Parts & Specifications Manual Part # Tailgate Assembly ( ) 1 9, , ,13,14 TO EXISTING HOLES IN BODY TAILGATE ASSEMBLY 3 BOTTOM SPRING CONNECTION TAILGATE INSTALLATION 12,13,14 TO EXISTING HOLES IN BODY 15 INSTALLATION NOTES: 1 INSTALL ROD WELDMENT #2 INTO PANEL #3 SLOTS. 2 CONNECT SPRING #7 BETWEEN PANEL #3 BRACKET AND ROD #2 BRACKET. 3 JOIN PANEL #1 OVER PANEL #3. 4 CONNECT PANEL #1 TO PANEL #3 WITH RIVET #6. 5 INSERT LOWER MOUNTING PIN OF MOUNTING BRACKETS #17 AND #18 INTO LOWER HOLE OF ASSEMBLED TAILGATE. 6 BOLT ASSEMBLY TO REAR OF BODY. 7 CABLE #15 WILL SHARE THE TOP MOUNTING HOLE IN BRACKETS #17 AND #18. ATTACH THE OTHER END OF CABLE TO THE TOP END OF THE TAILGATE TO HOLD THE TAILGATE PARALLEL TO THE CARGO FLOOR PARTS LIST ITEM PART # DESCRIPTION QUANTITY TAILGATE WELDMENT REAR COVER TAILGATE WELDMENT LATCH ROD TAILGATE WELDMENT FRONT COVER RIVET-ALUMINUM.257 DIA X.38 GRIP SPRING-COMPRESSION.50 X 3.50 X 14GA BRACKET, TAILGATE REAR COVER WASHER.25 FLAT (WAS ) CAP SCR.25-20X.75 HH GR5Z NUT HEX NYLOC (WAS ) WASHER.38 FLAT (WAS SS) CAP SCREW.38-16X 1.25 HHGR5Z (WAS ) NUT HEX NYLOC (WAS ) CABLE, PLASTIC COATED TAILGATE POST WELDMENT, RH TAILGATE POST WELDMENT, LH 1 REV. F 2007

83 Chapter 5 Tailgate & Bumper Options 81 Bumper Hitch & Workbench Options Dominator Bumper Hitch & Workbench Options PART NUMBER DESCRIPTION NOTES Pintle ball combination with 2" removable ball for hitch Tank Kit mounting Hitch for hitch Tank Kit mounting Vise mounting bracket Can be located on RH side, LH side, or both with quantity of Note: See drawing for installation instructions Combination vise, 5" Can be located on RH side, LH side, or both with quantity of Vise plate, weld-on 12" x 12" Can be located on RH side, LH side, or both with quantity of 2 x 1/2"

84

85 83 C HAPTER 6 Air System Options In This Chapter Air Tank Options Air Tank Kit, 22.5 Gallon ( ) Air Tank Kit, 15 Gal ( ) Air Tank Kit, Dual 15 Gal ( ) Air Tank Kit, 35 Gallon ( ) Air Tank Kit, 58 Gallon ( ) Stepless Ear Clamp Installation ( ) Moisture Separator / Regulator / Oiler Assembly ( ) Moisture Separator / Regulator / Oiler Parts ( ) Moisture Separator / Regulator / Oiler Installation Hose Reel ( ) Air Tank Options PART # DESCRIPTION LOCATION Air Tank Kit, 22.5 Gal Mount between the frame for all units Air Tank Kit, 2-15 Gal (30 Mount between the frame at the rear of the body. Gal Total) Air Tank Kit, 22 Gal Mount on one side parallel to driveshaft Air Tank Kits, 2-15 Gal Mount one on each side of frame. Tanks Air Tank Kit, 35 Gal Mount on top of street side compartments Air Tank Kit, 58 Gal Mount on top of street side compartments.

86 84 Dominator 2 Parts & Specifications Manual Part # Air Tank Kit, 22.5 Gallon ( ) (4) 11 SEE NOTE 2 5 SEE NOTE (2) 16(4) 2 4 9(12) TO FRONT 8(4) PARTS LIST 1 ITEM PART # DESCRIPTION QUANTITY DRAIN ASM (INCL:1) AIR TANK 22-1/2 GALLON ADAPTER 1/4MPT 1/4MPT HEX STREET ELBOW 3/4NPT TEE 1/ CAP SCR 1/2-13X1-1/2 HHGR5 (WAS ) NUT 1/2-13 LOCK WASHER 1/2 WRT REDUCER BUSHING 1-1/4X3/4NPT HOSE FTG TYPE O 1/4 1/ SAFETY VALVE 1/4 200PSI DECAL-DANGER EXPLODING TANK BRACKET SPRING CAP SCR 1/2-13X3-1/4 HHGR5 4 REV. J

87 Chapter 6 Air System Options 85 Air Tank Kit, 15 Gal ( ) NOTES: 1 LOCATE DECAL AS CLOSE TO DRAIN VALVE AS POSSIBLE, IN CLEAR VIEW OF OPERATOR. 2 FITTING CONFIGURATION MAY VARY PER APPLICATION. TANK BRACKET MAY BE MOUNTED INVERTED OR ROTATED 180 AS REQUIRED PER APPLICATION.

88 86 Dominator 2 Parts & Specifications Manual Part # PARTS LIST ITEM PART # DESCRIPTION QUANTITY TANK BRKT-DUAL 15GAL INSFRAME TANK-AIR 15 GAL X REDUCER BUSH-BLK ELBOW-STREET STL.75 X 90 DEG HOSE FTG-TYPE O BRS CLAMP-.75 STEPLESS EAR (WAS ) HOSE-GP.75 X 250 WP GRAY FT VALVE-PRESS RELIEF PS DRAIN ASM-DUAL AIR TANKS ELBOW-STREET BLK.25 X 90 DEG CAP SCR.50-13X 1.50 HH GR5 Z WASHER.50 W FLAT ANSI B27.2Z NUT HEX NYLOC ZINC PLUG-PIPE SOC HEX BLK PLUG-PIPE SQ HD BLK REDUCER BUSH-BLK DECAL-DANGER EXPLODING TANK 1 REV. C

89 Chapter 6 Air System Options 87 Air Tank Kit, Dual 15 Gal ( ) NOTES: 1 LOCATE DECAL AS CLOSE TO DRAIN VALVE AS POSSIBLE, IN CLEAR VIEW OF OPERATOR. 2 FITTING CONFIGURATION MAY VARY PER APPLICATION. TANK BRACKET MAY BE MOUNTED INVERTED OR ROTATED 180 AS REQUIRED PER APPLICATION PARTS LIST ITEM PART # DESCRIPTION QUANTITY TANK BRKT-SGL 15GAL BRACKET, AIR TANK CAP SCR 3/8-16 X CAP SCR 1/2-13 X NUT 1/2-13 HEX SELF LOCK NUT 3/8-16 HEX SELF LOCK WASHER 1/2 FLAT TANK, AIR 15 GAL HOSE-GP 3/4" 200 PSI 8' HOSE FTG 3/4 3/4 BRS ELBOW STR 3/4X RED BUSHING PIPE PLUG 1.25 HOL HEX PLUG-PIPE 3/8 SQHD SAFETY VALVE ELBOW STREET 1/4 X 90 1

90 88 Dominator 2 Parts & Specifications Manual Part # PARTS LIST ITEM PART # DESCRIPTION QUANTITY HOSE CLAMP DRAIN ASM, DUAL TANK RED BUSHING 3/8-1/ DECAL-DANGER AIR TANK 1 REV. B

91 Chapter 6 Air System Options 89 Air Tank Kit, 35 Gallon ( ) 4 7-REARWARD 1/4"FITTING 5-FORWARD 1/4"FITTING CURB SIDE 14-DRIVER SIDE FORWARD 1/4"FITTING 18-REARWARD 1/4"FITTING THESE TWO(2) CLAMPS USE THE SAME #

92 90 Dominator 2 Parts & Specifications Manual Part # NOTES: 1 ITEMS ARE USED TO SECURE TANK (#1) TO BRACKET (#4), AND BRACKET TO BODY. 2 ITEMS ARE USED TO SECURE CLAMP (#12) TO BODY. 3 ITEM 28 AND ONE OF ITEM 9 MAY NOT BE REQUIRED, OR MAY REPLACE ITEMS 14 & PARTS LIST ITEM PART # DESCRIPTION QUANTITY TANK-AIR 35 GAL X DECAL-AIR TANK DRAIN DECAL-DANGER EXPLODING TANK BRACKET-AIR TANK 58 GAL MECH PLUG-PIPE SQ HD BLK PLUG-PIPE SOC HD GLV VALVE-SAFETY PSI REDUCER BUSH-BLK ELBOW-STREET BLK.75 X 90 DEG NIPPLE-BARB BRS.75 MPT CLAMP-.75 STEPLESS EAR (WAS ) CLAMP-UMP20 S464-G HOSE-GP.75 X #300 WP (GRAY) 31' ELBOW-STREET BLK.75 X NIPPLE-PIPE BLK.75 X CLOSE VALVE-BALL HOSE FTG-TYPE O STL GAUGE-PRESSURE AIR 300# ELBOW-STREET BLK.25 X CAP SCR.25-20X 1.00 HH GR5Z WASHER.25 W FLAT ANSI B27.2Z NUT HEX NYLOC ZINC CAP SCR X 1.25 HH GR5 ZINC WASHER.38 W FLAT ANSI B27.2Z NUT HEX NYLOC ZINC CAP SCR X 1.00 HH GRD5 ZINC WASHER-BONDED PLTD NIPPLE-PIPE BLK.75 X REV. C REV. B

93 Chapter 6 Air System Options 91 Air Tank Kit, 58 Gallon ( ) ,18,19, 20,21, TO FLR 14,15, ,18,19, 20,21,22 TO COMPRESSOR NOTE: 1 LOCATE DECAL #24 AS CLOSE TO DRAIN VALVE AS POSSIBLE, IN CLEAR VIEW OF OPERATOR PARTS LIST ITEM PART # DESCRIPTION QUANTITY TANK-AIR 58 GAL BRACKET-AIR TANK 58 GAL MECH GAUGE-PRESS AIR 300# BTM MNT REDUCER BUSH-BLK TEE-BLK HOSE HTG-TYPE O STL NIPPLE-PIPE BLK.75 X CLOSE REDUCER BUSH-BLK VALVE-SAFETY PSI CAP SCR X 1.00 HH GR5 Z NUT HEX ZINC WASHER.38 W FLAT AHSI B27.2Z WASHER.38 LOCK ZINC 12

94 92 Dominator 2 Parts & Specifications Manual Part # PARTS LIST ITEM PART # DESCRIPTION QUANTITY DRAIN ASM-AIR TANK UNDER DECK CLAMP-HOSE VINYL COVERED RIVET-POP AL.12 X.375 GRIP HOSE-GP.75 X 300# WP (GRAY) 31 FT CLAMP-HOSE VINYL COVERED SCR-MACH.25-20X.75 BTNHD ZC WASHER.25 LOCK ZINC WASHER.25 W FLAT ANSI B27.2Z NUT HEX ZINC CLAMP-.75 STEPLESS EAR (WAS ) DECAL-DANGER EXPLODING TANK 1 REV. C

95 Chapter 6 Air System Options 93 Stepless Ear Clamp Installation ( ) INSTALLING A STEPLESS EAR CLAMP When there is sufficient room, use standard jaw pincers to position a properly-sized ear clamp on a hose fitted with a hose stem. Close ear clamp fully with uniform force until there is only a 1/16" gap remaining. The visible deformation of the clamp ear provides a visible, instant check that the closure is complete. INSTALLING A STEPLESS EAR CLAMP IN RESTRICTED SPACE When space is restricted, use side jaw pincers held parallel to the hose to position and clamp a properly-sized ear clamp on a hose fitted with a hose stem. Close ear clamp fully with uniform force until there is only a 1/16" gap remaining. The visible deformation of the clamp ear provides a visible, instant check that the closure is complete. REMOVING A STEPLESS EAR CLAMP To remove a stepless ear clamp, grasp the strip end with a pincer and pull it away. NOTE: Stepless ear clamps can only be used once. When removed, they must be discarded and replaced with new clamps.

96 94 Dominator 2 Parts & Specifications Manual Part # Moisture Separator / Regulator / Oiler Assembly ( ) NOTE: 1 When installing fittings, seal threads with Pro Lock pipe sealant with teflon (#51464) or equivalent. This sealant is a low strength anaerobic paste. Thread tape is not acceptable PARTS LIST ITEM PART # DESCRIPTION QUANTITY AIR PRESSURE GAUGE 300PSI MOISTURE SEP/REG/OILER STREET ELBOW 3/8NPT 45 BRASS REDUCER BUSHING 1/2-1/4NPT BRS STREET ELBOW 1/4NPT 90 SHORT TEE 3/8NPT BRS RUN TEE 1/2NPT BRS RUN REDUCER BUSHING 3/8-1/4NPT BRS BARB NIPPLE 1/2MPT 3/4NPT QUICK DISCONNECT 3/8MPT 1/4DIS 1

97 Chapter 6 Air System Options PARTS LIST CAP SCR-SS.25-20X 50HH * WASHER, SS 1/4 LOCK * T X5 2MIL ZIPLOC BAG * 4 * NOT SHOWN REV. B Moisture Separator / Regulator / Oiler Parts ( ) KIT-JOINER SET & T-BRACKET (TYP 2) SIGHT DOME ASM FILTER, COMPLETE PLUG, FILL W/O-RING LUBRICATOR, AIR, COMPLETE BOWL O-RING REGULATOR, COMPLETE BOWL O-RING COMPONENT PART ASSEMBLIES: FILTER REPLACEMENT PARTS INCLUDE ELEMENT KIT (5-MICRON ELEMENT, ELEMENT RETAINER, DEFLECTOR, AND BOWL O-RING) AND ELEMENT (5-MICRON ELEMENT ONLY) AIR REGULATOR REPLACEMENT PARTS INCLUDE DIAPHRAGM KIT AND SPRING, AIR REGULATOR LUBRICATOR REPLACEMENT PARTS INCLUDE BY-PASS KIT, WHICH INCLUDES MODULE, CHECK BALLS, ELASTOMER, AND GASKET.

98 96 Dominator 2 Parts & Specifications Manual Part # Moisture Separator / Regulator / Oiler Installation

99 Chapter 6 Air System Options 97 Hose Reel ( ) PARTS LIST ITEM PART # DESCRIPTION QUANTITY HOSE REEL STREET ELBOW, STL 1/2X90 (WAS ) PIPE CAP 1/2NPT CAP SCR 3/8-16X1 HHGR5Z 4REF NUT 3/8-16 LOCK 4REF WASHER 3/8 FLAT 8REF HOSE CLAMP (WAS QTY 2) 4REF BARB NIPPLE 1/2MPT 3/4HOSE (WAS QTY 2) HOSE 3/4 300# 36" HOSE GUIDE & ROLLER ASM BOLT, STV #10-24X3/4 FLH ZINC 4REF NUT #10-24 HEX LOCK 4REF HARDWARE KIT, HOSE REEL (INCL. 4-7,11,12) REF REV

100

101 99 C HAPTER 7 Telescoping Tops Telescopic Top Installation ( ) (6 PLCS) 27, , ,27,28 (8 PLCS) HEIGHT ABOVE SIDEPACK' WHEN ROOF IS RETRACTED: 18.25" FOR 43" ROOF 0.99" FOR 26" ROOF 1 (8 PLCS) 5,6 (2 PLCS) 16 8 (8 PLCS) 24,25 (2 PLCS) 7 (8 PLCS) 8 (2 PLCS) , 27, 28 (QUANTITY VARIES) (TWO SIDES) 26, 27, 28 (4 PLCS) NOTE: FOR ASSEMBLIES WITH SWING UP DOORS, REAR POST IS FLUSH WITH BACK OF SIDEPACK (2) , 24(2), 26 (6 PLCS) NOTE: THE COMPLETE ASSEMBLY DETAIL IS FOR THE 43" HIGH VERSION AND ITS ASSOCIATED "SWING" DOORS. VIEW ABOVE DETAILS THE 26" HIGH VERSION WITH SWING-UP DOOR. NOTE: FOR ASSEMBLIES WITH SWING OUT DOORS, REAR POST IS 0.9" BEHIND BACK OF SIDEPACK. SECURE POST ON CRANE BOX SIDE WITH ITEMS #22, 24, 26.

102 100 Dominator 2 Parts & Specifications Manual Part # Tethered Lid Assembly ( ) 2 4 Ø0.20 THRU VIEW FROM BOTTOM PARTS LIST ITEM PARTS # DESCRIPTION QTY LID-ASM 8IN PLSTC ACCESS COVER DOM T-TOP SCR-MACH #10-24X.75 RDH PH ZINC NUT HEX NLOCK WASHER-VONDED.19 PLTD LANYARD-16IN 1 LOOP 1 REV A

103 Chapter 7 Telescoping Tops PARTS LIST ITEM PART # DESCRIPTION QUANTITY ROLLER HINGE-SS 10GA BUTT LATCH ASM-3PT COMPRESSION BUMPER-RUBBER 1.25 DIA X NUT HEX KIT CAP SCR.38-16X 2.00 HH GR5ZC KIT SCR-MACH.25-20X.75TRHTORXSS KIT NUT-SS NYLOC KIT PIN-QUICK RLSE.50D/1.5 W/ 12inL SCR-THRD.CUT.31-18X.75 HWH-1 KIT 11. #11 (SEE CHART) ANGLE-T TOP FRONT FILLER #12 (SEE CHART) SPACER REAR POST 43 H #13 (SEE CHART) BRACKET-SIDE T TOP WLDMT #14 (SEE CHART) BRACKET-SIDE T TOP WLDMT #15 (SEE CHART) TRACK-T TOP LOWER RFLR #16 (SEE CHART) TOP-TELESCOPE REAR SECT #17 (SEE CHART) TOP-TELESCOPE CTR SECT #18 (SEE CHART) TOP-TELESCOPE FRT SECT #19 (SEE CHART) TRACK-T TOP LOWER LFRR #20 (SEE CHART) TRACK-T TOP UPPER LID-ASSEMBLY RIVET-POP AL.12 X.375 GRIP KIT SCR-MACH 10-24X 1.50 RDH KIT NUT HEX NYLOCK KIT WASHER.19 W FLAT ANSI B27.2Z KIT NUT HEX NYLOCK KIT WASHER.31 FLAT KIT CAP SCR.31-18X 1.00 HH GR5 Z KIT CAP SCR.31-18X 1.25 HH GR5 Z KIT 30. #30 (SEE CHART) DOOR-TEL TOP WLDMT FLIP UP DOOR #31 (SEE CHART) PANEL T-TOP REAR POST LR #33 (SEE CHART) DOOR-TEL TOP WLDMT W-SWING WO-LTCH #34 (SEE CHART) DOOR-TEL TOP WLDMT W-SWING W-LTCH #35 (SEE CHART) ROD-DOOR W/.75" OFFSET TOP #36 (SEE CHART) ROD-DOOR W/ 2.75" OFFSET BOTTOM DOOR CATCH-ASM ZINC 4" 2 PC #38 (SEE CHART) PANEL T-TOP REAR POST RR 1 REV. E

104 102 Dominator 2 Parts & Specifications Manual Part # TELESCOPING TOP COMPONENT KIT INFORMATION MODEL 9' L 26" H 9' L 43" H 11' L 26" H 11' L 43" H 13' L 26" H 14' L 26" H 14' L 43" H ITEM DESCRIPTION PART # ANGLE #11 N/A N/A N/A N/A SPACER #12 N/A N/A N/A N/A MTG BRACKET-SIDE # MTG BRACKET-SIDE #14 N/A N/A N/A N/A N/A TRACK-LOWER #15 N/A N/A N/A N/A TOP-REAR # TOP-CENTER # TOP-FRONT # TRACK-LOWER # TRACK-UPPER # LID ASSEMBLY # NA NA NA DOOR-HINGE UP # POST-LEFT REAR # DOOR-SWING W/O #33 N/A N/A N/A N/A LATCH DOOR-SWING #34 N/A N/A N/A N/A W/LATCH DOOR ROD-TOP # DOOR ROD-BOTTOM # POST-RIGHT REAR # HARDWARE KIT

105 103 C HAPTER 8 Boom Supports In This Chapter Boom Support ( ) Boom Support, Adjustable, 1015 & 2020 ( ) Boom Support, Adjustable, ( )

106 104 Dominator 2 Parts & Specifications Manual Part # Boom Support ( ) " DOMINATOR WITH 1015 CRANE " DOMINATOR WITH 2020 CRANE 65.50" DOMINATOR WITH CRANE

107 Chapter 8 Boom Supports 105 Boom Support, Adjustable, 1015 & 2020 ( ) NOTE: 1 Hardware included in kit # Rotate and arrange pedestal #2 and saddle #5 or #6 based on chassis exhaust PARTS LIST ITEM PART # DESCRIPTION QUANTITY CAP SCREW X 5 HHGR5Z (WAS ) PEDESTAL-WLDMT ADJ 3.5X3.5X WEAR PAD-RC UHMW.75X4.00X TUBE-PEDESTAL TEL 4.0X4.0X SADDLE-BOOM SUPT 1015/ SADDLE-BOOM SUPPORT DOM 3820 & UP CAP SCR.38-16X 1.50 HH GR5 Z CAP SCR.75-10X 6.00 HH GR5 Z NUT HEX NYLOCK NUT HEX NYLOCK 6

108 106 Dominator 2 Parts & Specifications Manual Part # PARTS LIST NUT HEX NYLOCK WASHER.38 FLAT WASHER.50 FLAT WASHER.75 FLAT WASHER-BONDED PLTD.38 4 REV. C

109 Chapter 8 Boom Supports 107 Boom Support, Adjustable, ( ) (4) 11(4) 15(4) 11(4) 9(4) NOTE: 1 1 Hardware included in kit # Rotate and arrange pedestal #1 and saddle #10 based on chassis exhaust PARTS LIST ITEM PART # DESCRIPTION QUANTITY PEDESTAL-WLDMT ADJ WEAR PAD (WAS ) TUBE-PEDESTAL SADDLE-BOOM SUPPORT DOM 3820 & UP CAP SCR.38-16X 1.50 HH GR5 Z CAP SCR.50-13X 5.00 HH GR5 Z NUT HEX NYLOCK NUT HEX NYLOCK NUT HEX NYLOCK WASHER.38 FLAT (WAS 8) WASHER.50 FLAT 4

110 108 Dominator 2 Parts & Specifications Manual Part # PARTS LIST WASHER.75 FLAT CAP SCR.75-10X 6.00 HH GR5 Z (WAS ) WASHER-BONDED PLTD.38 4 REV D

111 109 C HAPTER 9 Stabilizers In This Chapter Front Stabilizers ( / ) Rear Stabilizers, Manual Out / Manual Down ( / ) Rear Stabilizers, Manual Out / Manual Down ( / ) Rear Stabilizers, Manual Out/Power Down ( / ) Rear Stabilizers, Power Out/Power Down ( / ) Rear Stabilizers, Power Out/Power Down ( / ) Stabilizer Hydraulic Installation ( ) Cylinder, Power Out (3B142860) (Effective 2-07, prior to 8-05) Cylinder, Power Out ( ) (Used 9-05 to 1-07) Stabilizer Assembly ( ) Stabilizer Assembly, Stationary Mount ( ) Cylinder ( ) (Thru. 9-05, Eff. 2/07) Cylinder ( ) (Eff through 1/07) Valvebank, Power Out/Power Down ( ) (Eff ) Valvebank, Power Out/Power Down ( ) (Through ) Valvebank, Manual Out/Power Down ( ) (Eff ) Valvebank, Manual Out/Power Down ( ) (Through ) Stabilizer Override Installation & Operation ( )...138

112 110 Dominator 2 Parts & Specifications Manual Part # Front Stabilizers ( / ) A PARTS ARE UNIVERSAL FOR RIGHT OR LEFT SIDE INSTALLATION / PARTS LIST 2 DETAIL A SCALE 1/4 ITEM PART # DESCRIPTION QUANTITY STAB FRT TUBE EXT STAB FRT BTM PAD PIN-QUICK RLSE.50/2.5CRIT RNG CAP SCR.50-13X 3.50 HH ( ) NUT NYLOC ( ) 1 REV. A

113 Chapter 9 Stabilizers 111 Rear Stabilizers, Manual Out / Manual Down ( / )(Eff. 3/29/13) THIS PANEL IS USED TO BLOCK THE VALVEBANK OPENING ON THE BACK OF THE CRANE BOX (2) PARTS LIST ITEM PART # DESCRIPTION DETAILS QUANTITY CRANK ASSEMBLY CRANK HANDLE ARM-STABILIZER (DOM 1) 1 ADJUSTABLE MAN CRANK ARM-STABILIZER (DOM 2) 1 ADJUSTABLE MAN CRANK ARM-STABILIZER (DOM 1) 1 STATIONARY MAN CRANK ARM-STABILIZER (DOM 2) 1 STATIONARY MAN CRANK 7X PIN-STABILIZER STOP (DOM 1) PIN-STABILIZER STOP (DOM 2) SPRING 1

114 112 Dominator 2 Parts & Specifications Manual Part # PARTS LIST ITEM PART # DESCRIPTION DETAILS QUANTITY ROLLER UHMW.50 X 2.00 X 1.38 LG PIN PANEL-CRANE BOX VALVE 1 BLOCK COVER KNOB-CONTROL 1.50 BLK CAP SCREW.38-16X 1.00 HH GR5 Z CAP SCREW.50-13X 5.75 HH GR5 Z (DOM 2) CAP SCREW.50-13X 5.00 HH GR5 Z (DOM I) NUT HEX NYLOCK WASHER.38 LOCK WASHER.62 FLAT ASTM F COTTER PIN.12X1.00 PLAIN COTTER PIN.16X1.00 PLAIN 1 REV A

115 Chapter 9 Stabilizers 113 Rear Stabilizers, Manual Out / Manual Down ( / )(Through 3/28/13) 7 A B 4 A SECTION A-A DETAIL B PARTS LIST ITEM PART # DESCRIPTION DETAILS QUANTITY CRANK ASSEMBLY CRANK HANDLE ARM-STABILIZER (DOM 1) 1 ADJUSTABLE MAN CRANK ARM-STABILIZER (DOM 2) 1 ADJUSTABLE MAN CRANK ARM-STABILIZER (DOM 1) 1 STATIONARY MAN CRANK ARM-STABILIZER (DOM 2) 1 STATIONARY MAN CRANK 7X PIN-WELDMENT (DOM 1) PIN-WELDMENT (DOM 2) 1

116 114 Dominator 2 Parts & Specifications Manual Part # PARTS LIST ITEM PART # DESCRIPTION DETAILS QUANTITY SPRING ROLLER UHMW.50 X 2.00 X 1.38 LG PIN PANEL-CRANE BOX VALVE 1 BLOCK COVER KNOB-CONTROL 1.50 BLK CAP SCREW.38-16X 1.00 HH GR5 Z CAP SCREW.50-13X 5.75 HH GR5 Z (DOM 2) CAP SCREW.50-13X 5.00 HH GR5 Z (DOM I) NUT HEX NYLOCK WASHER.38 LOCK MACHY BUSHING.75X14 GA NR (WAS ) COTTER PIN.12X1.00 PLAIN COTTER PIN.16X1.00 PLAIN 1 REV

117 Chapter 9 Stabilizers 115 Rear Stabilizers, Manual Out/Power Down ( / ) DECAL PLACED ABOVE 26VALVE BANK INSIDE CRANE BOX. 22, VALVE IS INSTALLED ON BACK WALL OF CRANE BOX. 21, (2) (4) 16(3) LOCK PIN IS LOCATED IN CRANE BOX. 20, (2) 1 33(2) 15(4) CJ-200 CJ CJ-205 CONNECTS TO ELECTRICAL PANEL (INSIDE CRANE BOX) CJ CP-206 CP PARTS LIST CJ-201 CJ-203 CJ-204 ITEM PART # DESCRIPTION QUANTITY STABILIZER ASM EXTENSION (DOM 2) STABILIZER ASM STATIONARY MOUNT (DOM 1 2) PIN-WLDMT - T (DOM 2) 1

118 116 Dominator 2 Parts & Specifications Manual Part # PARTS LIST ITEM PART # DESCRIPTION QUANTITY WEAR PAD-RC 2.00 X 2.00 X WEAR PAD-RC 2.00 X 2.00 X VALVE BANK 2 SEC W/SOLENOIDS (WAS THROUGH ) HARNESS-DOM(II) STABILIZER REF KIT HOSE MANUAL OUT HYD STABILIZERS REF HOSE-FJ.25 X OAL (4-6) 100R HOSE-FZ.25 X OAL (4-6) 100R HOSE-FJ.25 X OAL (4-6) 100R HOSE-FZ.25 X OAL (4-6) 100R HOSE-FF.25 X (4-4) 100R ELBOW-M STR/90/M JIC ELBOW-M STR/M JIC XLG ELBOW-M STR/90/M JIC 8 8 REF ADPTR-M STR/M JIC ELBOW-M JIC/90/M JIC 4 4 BLKHD ADPTR-M STR/M JIC CAP SCR.31-18X 2.50 HH GR5 Z CAP SCR.31-18X 1.25 HH GR5 Z CAP SCR.50-13X 1.50 HH GR8 Z CAP SCR.38-16X 4.00 HH GR5 Z NUT HEX NYLOCK NUT HEX TOP LOCK GR8 Z WASHER.38 LOCK DECAL-STABILIZER MANUAL OVERRIDE 1 (WAS THROUGH ) COTTER PIN.12X1.00 PLAIN COTTER PIN.16X1.00 PLAIN PIN-TYPE O.50X 2.88 ( 2.63) SPRING-COMPRESSION.062 X 1.50 X.845OD ROLLER-UHMW.50 X 2.00 X 1.38 LG CAM CLAMP 1.00 DIA. X CLAMP-.62 LOOP CUSHIONED MACHY BUSHING.75X14 GA NR WLDMT CHANNEL HOSE CARRIER 1 REV B

119 Chapter 9 Stabilizers 117 Rear Stabilizers, Power Out/Power Down ( / )(Eff. 3/29/13) PARTS LIST ITEM PART # DESCRIPTION QUANTITY STABILIZER ASM EXTENSION STABILIZER ASM STATIONARY MOUNT PIN STABILIZER STOP WEAR PAD-RC 2.00 X 2.00 X

120 118 Dominator 2 Parts & Specifications Manual Part # PARTS LIST ITEM PART # DESCRIPTION QUANTITY WEAR PAD-RC 2.00 X 2.00 X VALVE BANK 3 SEC W/SOLENOIDS HARNESS-STABILIZER REF HOSE KIT-POWER OUT HYD STABILIZERS REF HOSE-FZ.25 X OAL (4-6) 100R HOSE-FJ.25 X OAL (4-6) 100R HOSE-FJ.25 X OAL (4-6) 100R HOSE-FZ.25 X OAL (4-6) 100R HOSE-FJ.25 X OAL (4-6) 100R HOSE-FZ.25 X OAL (4-6) 100R HOSE-FF.25 X (4-4) 100R ELBOW-M STR/90/M JIC ELBOW-M STR/M JIC XLG ELBOW-M JIC/F JIC SW ELBOW-M JIC/90/M JIC 4 4 BLKHD ELBOW-M STR/90/M JIC ADPTR-M STR/M JIC ADPTR-M STR/M JIC ADPTR-M STR/M JIC B CYLINDER DECAL-STABILIZER MANUAL OVERRIDE, 1 SOFT SHIFT (WAS THROUGH ) CAP SCR.31-18X 2.50 HH GR5 Z CAP SCR.31-18X 1.25 HH GR5 Z CAP SCR.50-13X 1.50 HH GR8 Z CAP SCR.50-13X 5.75 HH GR5 Z CAP SCR.38-16X 4.00 HH GR5 Z NUT HEX NYLOCK NUT HEX TOP LOCK GR8 Z NUT HEX NYLOCK WASHER.38 LOCK COTTER PIN.12X1.00 PLAIN COTTER PIN.16X1.00 PLAIN WELDMENT, CHANNEL HOSE CARRIER CAM CLAMP 1.00 DIA. X CLAMP-.62 LOOP CUSHIONED WASHER.62 FLAT SPRING-COMPRESSION.062X1.50X.845 OD ROLL PIN.50X REV E

121 Chapter 9 Stabilizers 119 Rear Stabilizers, Power Out/Power Down ( / )(Through 3/28/13) 20 3 OR 4 19 DECAL PLACED ABOVE VALVE BANK INSIDE CRANE BOX 28 31,35 32,34 21, (2) 22(2) 40 33, OR ,32 46 VALVE IN INSTALLED ON BACK WALL OF CRANE BOX LOCK PIN LOCATED IN CRANE BOX (6) 26(3) OR 2 42(2) 19(4) CP CJ-200CJ-202 CJ-205 HARNESS CONNECTS TO ELECTRICAL PANEL INSIDE CRANE BOX. CJ-400 VIEW FROM REAR OF CRANE BOX CJ-201CJ-203 CJ-204 CP-401 PARTS LIST ITEM PART # DESCRIPTION QUANTITY STABILIZER ASM EXTENSION STABILIZER ASM STATIONARY MOUNT PIN WEAR PAD-RC 2.00 X 2.00 X

122 120 Dominator 2 Parts & Specifications Manual Part # PARTS LIST ITEM PART # DESCRIPTION QUANTITY WEAR PAD-RC 2.00 X 2.00 X VALVE BANK 3 SEC W/SOLENOIDS HARNESS-STABILIZER REF HOSE KIT-POWER OUT HYD STABILIZERS REF HOSE-FZ.25 X OAL (4-6) 100R HOSE-FJ.25 X OAL (4-6) 100R HOSE-FJ.25 X OAL (4-6) 100R HOSE-FZ.25 X OAL (4-6) 100R HOSE-FJ.25 X OAL (4-6) 100R HOSE-FZ.25 X OAL (4-6) 100R HOSE-FF.25 X (4-4) 100R ELBOW-M STR/90/M JIC ELBOW-M STR/M JIC XLG ELBOW-M JIC/F JIC SW ELBOW-M JIC/90/M JIC 4 4 BLKHD ELBOW-M STR/90/M JIC ADPTR-M STR/M JIC ADPTR-M STR/M JIC ADPTR-M STR/M JIC B CYLINDER DECAL-STABILIZER MANUAL OVERRIDE, 1 SOFT SHIFT (WAS THROUGH ) CAP SCR.31-18X 2.50 HH GR5 Z CAP SCR.31-18X 1.25 HH GR5 Z CAP SCR.50-13X 1.50 HH GR8 Z CAP SCR.50-13X 5.75 HH GR5 Z CAP SCR.38-16X 4.00 HH GR5 Z NUT HEX NYLOCK NUT HEX TOP LOCK GR8 Z NUT HEX NYLOCK WASHER.38 LOCK COTTER PIN.12X1.00 PLAIN COTTER PIN.16X1.00 PLAIN WELDMENT, CHANNEL HOSE CARRIER CAM CLAMP 1.00 DIA. X CLAMP-.62 LOOP CUSHIONED MACHY BUSHING.75X14 GA NR SPRING-COMPRESSION.062X1.50X.845 OD ROLL PIN.50X REV D

123 Chapter 9 Stabilizers 121 Stabilizer Hydraulic Installation ( ) Drawing 4 3 POWER OUT CYLINDER CURBSIDE STABILIZER 12 BULKHEAD USE FITTINGS STREETSIDE STABILIZER PARTS LIST ITEM PART # DESCRIPTION QUANTITY KIT HOSE MANUAL OUT HYD STABILIZERS REF KIT HOSE POWER OUT HYD STABILIZERS REF ELBOW-M STR/90/M JIC ELBOW-M STR/M JIC XLG ELBOW-M JIC/90/F JIC SW ELBOW-M JIC/90/M JIC 4 4 BLKHD VALVE BANK 3 SEC W/SOLENOIDS DOM STABILIZERS VALVE BANK 2 SEC W-SOLENOIDS DOM STABILIZERS HOSE-FZ.25 X (4-6) 100R HOSE-FJ.25 X (4-6) 100R HOSE-FZ.25 X (4-6) 100R HOSE-FJ.25 X (4-6) 100R HOSE-FF.25 X (4-4) 100R HOSE-FZ.25 X (4-6) 100R HOSE-FJ.25 X (4-6) 100R17 1 NEW

124 122 Dominator 2 Parts & Specifications Manual Part # Drawing 8 B3 B2 B1 PB P A3 A2 A1 T ITEM DESCRIPTION PORT SIZE B3 POWER OUT CYLINDER RETURN -6 A3 POWER OUT CYLINDER PRESSURE -6 B2 CURB SIDE POWER DOWN RETURN -6 A2 CURB SIDE POWER DOWN PRESSURE -6 B1 STREET SIDE POWER DOWN RETURN -6 A1 STREET SIDE POWER DOWN PRESSURE -6 T TANK PORT -8 PB POWER BEYOND PORT -8 P PRESSURE PORT -8

125 Chapter 9 Stabilizers 123 Cylinder, Power Out (3B142860) (Effective 2-07, prior to 8-05) SAE #4 O-RING PORTS (2) 7, Ø CYLINDER DATA CLOSED LENGTH OPEN LENGTH STROKE PISTON TORQUE CARTRIDGE TORQUE / 49.85" CLOSED / 91.59" OPEN / 41.84" STROKE FT-LB FT-LB CLOSED OPEN STROKE NOTES: 1 REPLACE ALL COMPONENTS OF THE SEAL KIT WHENEVER THE CYLINDER IS DISASSEMBLED. THIS WILL REDUCE FUTURE DOWNTIME. 2 APPLY REGULAR GRADE ANTI-SEIZE AND LUBRICATING COMPOUND TO THE THREADS ON THE CYLINDER HEAD ONLY. KEEP AWAY FROM ALL SEALS. 3 APPLY "LUBRIPLATE" NO MEDIUM HEAVY, MULTI-PURPOSE LUBRICANT, TO ALL PISTON HEAD GLAND AND HOLDING VALVE SEALS, NYLON LOCK RING, CAST IRON PISTON RINGS, AND ROD STINGER THREADS. 4 TORQUE PISTON TO FT-LB, CARTRIDGE TO FT-LB. 3B PARTS LIST ITEM PART # DESCRIPTION QUANTITY 1. 4B CASE ASM G ROD ASM C STOP TUBE H HEAD I PISTON B SEAL KIT REF 7. 7Q O-RING Q O-RING Q10P214 BACKUP RING R U-CUP SEAL R13P007 ROD WIPER T66P012 PISTON SEAL RETAINING RING 1 REV B

126 124 Dominator 2 Parts & Specifications Manual Part # Cylinder, Power Out ( ) (Used 9-05 to 1-07) 50.0 ± 0.12" RETRACT EXTEND 42.0 ± 0.06" STROKE DETAIL B DETAIL A DETAIL A SCALE 4:1 DETAIL B SCALE 3:1 NOTES: 1 TO REDUCE DOWNTIME, REPLACE ALL COMPONENTS OF THE SEAL KIT WHENEVER THE CYLINDER IS DISASSEMBLED CYLINDER DATA EXTENDED 1.23 IN², 0.22 GAL RETRACTED 0.79 IN², 0.14 GAL CASE 1.25 BORE X ø1.63 ROD ø DRY WEIGHT 19.7 LB TEST PRESSURE 3000 PSI OPERATING PRESSURE 2500 PSI PORTS SAE #4 O-RING BOSS (7/16-20 UNF-2B) CYLINDER TUBE BURST PRESSURE 20,000 PSI TORQUE TORQUE LOCKNUT (#6) WITH THREADLOCK COMPOUND TO FT-LB PARTS LIST ITEM PART # DESCRIPTION QUANTITY CASE WELDMENT ROD WELDMENT HEAD GLAND PISTON REF- LOCKNUT 1-14 UNS SEAL KIT 1 NEW

127 Chapter 9 Stabilizers 125 Stabilizer Assembly ( ) 5 A SECTION A-A A PARTS LIST ITEM PART # DESCRIPTION QUANTITY STABILIZER WELDMENT- SLIDEOUT ASM P PORT TUBE OD X LG ELBOW-M STR/90/M JIC RING-LOCK DOMINATOR STABILIZER RETAINING RING-4.50 DIA X.120 1

128 126 Dominator 2 Parts & Specifications Manual Part # SET SCR-SS.38-16X.50 SOC HEAD CYLINDER-3.50 BORE X 18.00S 28.38CC O.R (WAS THRU 1/07) 1 REV. F Stabilizer Assembly, Stationary Mount ( ) SECTION A-A A A PARTS LIST ITEM PART # DESCRIPTION QUANTITY STABILIZER MOUNT WELDMENT P PORT TUBE OD X LG 1

129 Chapter 9 Stabilizers ELBOW-M STR/90/M JIC RING-LOCK DOMINATOR STABILIZER RETAINING RING-4.50 DIA X SET SCR-SS.38-16X.50 SOC HEAD CYLINDER-3.50 BORE X 18.00S 28.38CC O.R (WAS THRU 1/07) REV. E Cylinder ( ) (Thru. 9-05, Eff. 2/07) B B NOTES: DRILL #15 HOLE 3/16" DEEP. PRESS IN PIN # REPLACE ALL COMPONENTS OF THE SEAL KIT WHENEVER THE CYLINDER IS DISASSEMBLED. THIS WILL REDUCE FUTURE DOWNTIME. 2 APPLY REGULAR GRADE ANTI-SEIZE AND LUBRICATING COMPOUND TO THREADS ON CYLINDER HEAD ONLY. KEEP AWAY FROM ALL SEALS. 3 APPLY "LUBRIPLATE" NO MEDIUM HEAVY, MULTI-PURPOSE LUBRICANT, TO ALL PISTON, HEAD GLAND, AND HOLDING VALVE SEALS, NYLON LOCK RING, CAST IRON PISTON RINGS, AND ROD STINGER THREADS. 4 ITEM #6, STOP TUBE, REPLACES 6A WAFER LOCK. USE STOP TUBE INSTEAD OF WAFER LOCK WHEN RESEALING CYLINDER. 5 PRESS LOCKING PIN (ITEM #17) INTO #15 HOLE DRILLED DEEP. 6 TORQUE PISTON TO FT-LB, HEAD TO 350 FT-LB, AND CARTRIDGE TO FT-LB.

130 128 Dominator 2 Parts & Specifications Manual Part # PARTS LIST ITEM PART # DESCRIPTION QUANTITY 1. 4G ROD ASSEMBLY CASE ASSEMBLY ID35125 PISTON HD35025 HEAD c STOP TUBE STOP TUBE (WAS 6A025025) Q O RING 3.12X 3.50X Q10P338 BACKUP RING-3.12 ID X 3.50 OD T61N125 LOCK RING-NYLON T66P035 PISTON SEAL Q O RING 3.00X 3.19X R14P025 ROD WIPER-TYPE D 2.25 ROD T2N4035 WEAR RING-PISTON 3.50X3.25X T2NX427 WEAR RING-ROD 2.50 ID X 0.50W HAL R U-CUP LOADED 2.50X3.00X.38 "B VALVE-CHECK PILOT/OPEN NONVENT LOCKING PIN D SEAL KIT (WAS 9C142020) (INCL 7-15,17) 1 REV. C

131 Chapter 9 Stabilizers 129 Cylinder ( ) (Eff through 1/07) SAE #4 O-RING BOSS (7/16-20 UNF) SAE #8 O-RING BOSS (3/4-16 UNF-2B) SAE #8 O-RING BOSS (3/4-16 UNF-2B) ± 0.06" STROKE ± 0.12 RETRACT EXTEND NOTES: 1 TO REDUCE DOWNTIME, REPLACE ALL COMPONENTS OF THE SEAL KIT WHENEVER THE CYLINDER IS DISASSEMBLED CYLINDER DATA EXTENDED 9.62 IN², 0.75 GAL RETRACTED 4.71 IN², 0.37 GAL CASE 3.50 BORE X ø4.50 ROD ø2.50 DRY WEIGHT 90.7 LB TEST PRESSURE 3500 PSI OPERATING PRESSURE 3000 PSI PORTS SAE #8 O-RING BOSS (3/4-16 UNF-2B) (QTY 2) AND SAE #4 O-RING BOSS (7/16-20 UNF-2B) (QTY 2) CYLINDER TUBE BURST PRESSURE 19,380 PSI TORQUES TORQUE LOCKNUT (#5) WITH THREADLOCK COMPOUND TO FT-LB USING LOCTITE GRADE 271 OR EQUIVALENT. TORQUE O-RING BOSS PLUG (#6) WITH THREADLOCK COMPOUND TO FT-LB USING LOCTITE GRADE 243 OR EQUIVALENT. TORQUE HEAD GLAND (#3) TO FT-LB. TORQUE CHECK VALVE TO FT-LB CYLINDER DATA ITEM PART # DESCRIPTION QUANTITY CASE WELDMENT ROD WELDMENT HEAD GLAND PISTON 1 5. REF LOCKNUT, UNF 1 6. REF PLUG, #4 STEEL HEX HOL SEAL KIT CHECK VALVE PO 1 NEW

132 130 Dominator 2 Parts & Specifications Manual Part # Valvebank, Power Out/Power Down ( ) (Eff ) NOTE: EFFECTIVE S/N DOMS2S P SCHEMATIC A1 B1 A2 B2 A3 1 4 PB A 2B 2C 8 NOTES (SEE REFERENCE NUMBER IN BOX): 1 TORQUE TO 25 FT-LB. 2 TORQUE TO 3 FT-LB. 3 TORQUE TO 90 FT-LB. B3 V2 T

133 Chapter 9 Stabilizers PARTS LIST ITEM PART # DESCRIPTION QUANTITY VALVE BANK 3 SEC W/SOLENOIDS DOM 1 STAB VALVE-SOLENOID (INCLUDES 2 OF ITEM ) COIL-12VDC LEAD WIRE VALVE-RELIEF 3200 PSI VALVE-SOLENOID SOFT SHIFT (INCLUDES 1 ITEM ) COIL-12VDC 36W LEADWIRE MANIFOLD SAE -2 PLUG SAE -4 PLUG SAE -6 PLUG SAE -8 PLUG 2 NEW

134 132 Dominator 2 Parts & Specifications Manual Part # Valvebank, Power Out/Power Down ( ) (Through ) NOTE: EFFECTIVE THROUGH S/N DOMS2S , 4 3, 3, 3, , ,8 9 DATE CODE 1 6 A B PUSH BUTTON OVERRIDES THE 4W3P VALVE TO THIS POSITION. P T P A1 B1 A2 B2 A3 B3 3A 3B 3C 4 90 PSI PSI PB HYDRAULIC SCHEMATIC T PARTS LIST ITEM PART # DESCRIPTION QUANTITY VALVE, RELIEF 3000 PSI VALVE, POPPET 1

135 Chapter 9 Stabilizers PARTS LIST VALVE, SPOOL COIL, 12V PLUG, ORIFICE 1 6. MANIFOLD 1 7. PLUG, EXPANDER 3 8. PLUG, SAE # PLUG, SAE # NAME PLATE CHECK VALVE COIL, 12VDC ORIFICE DISK, DIA WIRE MARKERS 1REF PLASTIC PLUG, SAE #8 3

136 134 Dominator 2 Parts & Specifications Manual Part # Valvebank, Manual Out/Power Down ( ) (Eff ) NOTE: EFFECTIVE S/N DOMS2S SCHEMATIC A1 B1 A2 B2 A3 B3 P A B 8 20 V2 9 1 PB T NOTES (IF TIED TO DRAWING, SEE REFERENCE NUMBER IN ): 1 TORQUE TO 25 FT-LB. 2 TORQUE TO 3 FT-LB. 3 TORQUE TO 90 FT-LB.

137 Chapter 9 Stabilizers PARTS LIST ITEM PART # DESCRIPTION QUANTITY VALVE BANK 2 SEC W/SOLENOIDS STAB VALVE-SOLENOID (INCLUDES 2 OF ITEM ) COIL-12VDC LEAD WIRE VALVE-RELIEF 3200 PSI VALVE-SOLENOID SOFT SHIFT (INCLUDES 1 ITEM ) COIL-12VDC 36W LEADWIRE MANIFOLD SAE -2 PLUG SAE -4 PLUG SAE -6 PLUG SAE -8 PLUG PLUG-CAVITY 1 NEW

138 136 Dominator 2 Parts & Specifications Manual Part # Valvebank, Manual Out/Power Down ( ) (Through ) NOTE: EFFECTIVE THROUGH S/N DOMS2S , 4 3, 12 3, CONNECTOR CONNECTOR ,8 9 DATE CODE NOTE: PUSH BUTTON OVERRIDES THE 4W3P VALVE TO THIS POSITION. A B P T A1 B1 A2 B2 A3 B3 P 2 PB 3A PSI 3B 3C 4 HYDRAULIC SCHEMATIC T PARTS LIST ITEM PART # DESCRIPTION QUANTITY VALVE, RELIEF 3000 PSI VALVE, POPPET VALVE, SPOOL COIL, 12V PLUG, ORIFICE 1

139 Chapter 9 Stabilizers PARTS LIST 6. MANIFOLD 1 7. PLUG, EXPANDER 3 8. PLUG, SAE # PLUG, SAE # NAME PLATE PLUG, CAVITY COIL, 12VDC PLUG, SAE # PLUG, SAE # I.D. TAGS 1REF PLUG, PLASTIC, SAE #6 4 PLUG, PLASTIC SAE #8 3

140 138 Dominator 2 Parts & Specifications Manual Part # Stabilizer Override Installation & Operation ( ) RIGHT LEFT STAB LEG STAB LEG RIGHT STAB ARM (IF APPLICABLE) PLUNGER LOCKING COLLAR 1 OR USE 9/64" ALLEN WRENCH PLASTIC CAP INSTALLING MANUAL OVERRIDE 1 REMOVE PLASTIC CAP AND DISCARD. 2 REPLACE PLASTIC CAP WITH ITEMS 3, 4, AND 5 AS SHOWN. 3 TURN ADJUSTMENT SCREW (ITEM 4) CLOCKWISE UNTIL YOU FEEL RESISTANCE. TURN COUNTERCLOCKWISE 2 FULL TURNS. 4 TIGHTEN JAM NUT (ITEM 3).

141 Chapter 9 Stabilizers 139 MANUAL OVERRIDE PROCEDURE 1 LOOSEN JAM NUT (ITEM 3). 2 TURN ADJUSTMENT SCREW (ITEM 4) CLOCKWISE UNTIL IT BOTTOMS OUT (APPROXIMATELY 6 FULL TURNS). 3 RAISE LOCKING COLLAR AND PUSH PLUNGER DOWN TO RETRACT DESIRED FUNCTION, OR LIFT TO EXTEND DESIRED FUNCTION. 4 RELEASE PLUNGER. 5 RELEASE LOCKING COLLAR ON ANY VALVE ACTIVATED. 6 PUSH AND RELEASE PLUNGER TO RETURN LOCKING COLLAR TO NEUTRAL POSITION. 7 RETURN ADJUSTMENT SCREW (ITEM 4) TO ORIGINAL POSITIONS. 8 TIGHTEN JAM NUT (ITEM 3) PARTS LIST ITEM PART # DESCRIPTION QUANTITY VALVE BANK 3 SEC W/SOLENOIDS REF VALVE BANK 2 SEC W/SOLENOIDS REF NUT # 8-32 HEX ZINC CAP SCR # 8-32X.75 SH PLAIN CAP-STABILIZER VALVE MANUAL OVERRIDE KIT-DOM STABILIZER VALVE OVERRIDE (INCL. ITEMS 3-5) REF NEW

142

143 141 C HAPTER 10 Electrical Options & Installation In This Chapter Electrical Installation ( ) (Eff ) Electrical Installation ( ) (Eff thru ) Electrical Installation ( ) (Through ) Electrical Panel ( ) Chassis Electrical Installation ( ) (Eff ) Power Panel (Dom 1-2) ( ) Power Panel Harness (Dom 4) ( ) Fuse Block, EFM, & Relay Bracket Installation ( ) (Thru ) Crane Installation Comparison Light Installation ( ) By-Pass Procedure for Reverse Activated Floodlights Electrical Outlet ( ) Light Reel Kits

144 142 Dominator 2 Parts & Specifications Manual Part # Electrical Installation ( ) (Eff ) ,10, ,18, ,2,3,4 9,10,31 13,14, NOTES (SEE REFERENCE NUMBER IN BOX): 1 LICENSE PLATE KIT TERMINATE WITH , AND GROUND EYELET FROM HARNESS ATTACHES TO ONE OF THE SCREWS. 2 CHASSIS GROUND AND BODY GROUND EYELETS FROM LIGHTING HARNESS SHOULD BE ATTACHED TO CHASSIS AND BODY, RESPECTIVELY. USE HARDWARE ITEMS #23, 24, 25, AND 26. DRILL AS NEEDED. 3 USE HEATSHRINK TO PROTECT UNUSED COMPARTMENT LIGHT CONNECTOR.

145 Chapter 10 Electrical Options & Installation 143 HARNESS REAR OF BODY: TAILLIGHTS, MARKER LIGHTS, ETC. VIEW OF BODY SHOWN WITHOUT DOORS OR SIDEPACK TOPS HARNESS AS PART OF CONTROL PANEL: CHASSIS, CRANE, STABILIZER, LIGHT CONTROLS HARNESS ONE PER SIDEPACK: FLOODLIGHTS, COMPARTMENT LIGHTS EXTENSION HARNESS TO FRONT MARKER LIGHTS, FLOODLIGHTS; (SEE LIST) NOTES (SEE REFERENCE NUMBER IN BOX): 1 EXTENSION HARNESS TO FRONT MARKER LIGHT AND FLOODLIGHTS. ONE PER SIDE 2 9' HARNESS ' HARNESS ', 14' HARNESS ' HARNESS PARTS LIST ITEM PART # DESCRIPTION QUANTITY ELECTRICAL PANEL (DOM4) ELECTRICAL PANEL (DOM1 & DOM2) WASHER.31 LOCK CAP SCR.31-18X.50 HH GR5 Z EDGING-PLASTIC BLK (DOM IV ONLY) A/R LIGHT-3-BAR LED WASHER.19 W FLAT ANSI B27.2Z NUT HEX NYLOCK LIGHT-LICENSE PLATE MTG BRACKET-WIRE HARNESS (DOM IV) 2

146 144 Dominator 2 Parts & Specifications Manual Part # PARTS LIST ITEM PART # DESCRIPTION QUANTITY MTG BRKT-WIRE HARNESS (DOM I AND II) CAP SCR.31-18X 1.00 HH GR5 Z WASHER.31 FLAT NUT HEX NYLOCK ALARM-BACK UP HORN CAP SCR.25-20X 1.25 HH GR5 Z (WAS ) WASHER.25 FLAT NUT HEX NYLOCK CAP SCR.38-16X 1.25 HH GR5 Z WASHER.38 W FLAT ANSI B27.2Z WASHER.38 LOCK ZINC NUT HEX NYLOC ZINC LIGHT-STOP/TURN/TAIL LED 4in DIA (WAS ) LIGHT-BACKUP 4" CLEAR GROMMET-RUBBER TAIL LIGHT 4" SCR-MACH #10-24X.75 RDH PH ZINC LIGHT-CLEARANCE RED LED OVAL 2 W/GROMMET LIGHT-CLEARANCE RED LED ROUND 2 W/GROMMET LIGHT-CLEARANCE AMBER LED OVAL 2 W/GROMMET LIGHT-CLEARANCE AMBER LED ROUND W/GROMMET 2 REV. G

147 Chapter 10 Electrical Options & Installation 145 Electrical Installation ( ) (Eff thru ) TERMINATE WITH , , AND LICENSE PLATE GROUND EYELET KIT FROM HARNESS TO BE ATTACHED TO ONE OF THE SCREWS. 8,9,10, ,18, ,9,10 CHASSIS GROUND AND BODY GROUND EYELETS FROM LIGHTING HARNESS TO BE ATTACHED TO CHASSIS & BODY, RESPECTIVELY. USE HARDWARE #23 - #26 AND DRILL AS NEEDED. 13,14, ,10,22 1,2,3,4 USE HEATSHRINK TO PROTECT UNUSED COMPARTMENT LIGHT CONNECTOR.

148 146 Dominator 2 Parts & Specifications Manual Part # HARNESS INSTALLATION HARNESS REAR OF BODY: TAIL LIGHTS, MARKER LIGHTS, ETC. VIEW OF BODY SHOWN WITHOUT DOORS OR SIDEPACK TOPS. HARNESS ONE PER SIDEPACK: FLOODLIGHTS, COMPT. LIGHTS HARNESS AS PART OF CONTROL PANEL: CHASSIS, CRANE, STABILIZER, LIGHT CONTROLS. EXTENSION HARNESS TO FRONT MARKER LIGHT, FLOODLIGHTS; ONE PER SIDE. 9' ' ' ' PARTS LIST ITEM PART # DESCRIPTION QUANTITY ELECTRICAL PANEL (DOM 1,2) ELECTRICAL PANEL (DOM 4) WASHER.31 LOCK CAP SCR.31-18X.50 HH GR5 Z EDGING-PLASTIC BLK GROMMET-2IN DIA LED MARKER LIGHT-CLEAR AMBER LED 2in DIA LIGHT-3 BAR LED SCR-MACH #10-24X.75 RDH PH ZINC WASHER.19 W FLAT ANSI B27.2Z NUT HEX NYLOCK LIGHT-LICENSE PLATE PLASTIC MTG BRKT-WIRE HARNESS CAP SCR.31-18X 1.00 HH GR5 Z WASHER.31 FLAT NUT HEX NYLOCK ALARM-BACK UP HORN SCR-MACH.25-20X.75 BTNHD ZC WASHER.25 FLAT NUT HEX NYLOCK LIGHT-STOP/TURN/TAIL LED ELEMENT LIGHT-CLEAR BACK UP LIGHT-MARKER CLEAR RED LED THIN LINE 2

149 Chapter 10 Electrical Options & Installation PARTS LIST ITEM PART # DESCRIPTION QUANTITY CAP SCR.38-16X 1.25 HH GR5 Z WASHER.38 W FLAT ANSI B27.2Z WASHER.38 LOCK ZINC NUT HEX NYLOC ZINC GROMMET 6 REV. A Electrical Installation ( ) (Through ) TERMINATE WITH ITEMS #25,26,27. ATTACH GROUND EYELET FROM HARNESS TO ONE OF THE SCREWS. LICENSE PLATE HARDWARE KIT # HARNESS ONE PER SIDEPACK: FLOODLIGHTS, COMPARTMENT LIGHTS 5,21,22,23 3,18, HARNESS REAR OF BODY: TAILLIGHTS, MARKER LIGHTS, ETC ,13,14 4 1, 8, 9 USE HEATSHRINK TO PROTECT UNUSED COMPARTMENT LIGHT CONNECTOR.

150 148 Dominator 2 Parts & Specifications Manual Part # DRAWING B BOTTOM OF BODY 17,18,19 10 CHASSIS GROUND AND BODY GROUND EYELETS FROM HARNESS TO BE ATTACHED TO CHASSIS AND BODY, RESPECTIVELY. USE HARDWARE ITEMS AND DRILL AS NECESSARY. DETAIL B A REAR OF BODY 15 DETAIL A 16,17

151 Chapter 10 Electrical Options & Installation PARTS LIST ITEM PART # DESCRIPTION QUANTITY ELECTRICAL PANEL EDGING-PLASTIC BLK LIGHT-MODULE, LH W/ LED MARKER LIGHT-MODULE, RH W/ LED MARKER LIGHT-LICENSE PLATE, PLASTIC GROMMET-RUBBER LIGHT-CLEAR AMBER 30200Y WASHER.31 LOCK CAP SCR-SS.31-18X.50 HH ALARM-BACK UP HORN MTG BRKT-WIRE HARNESS WASHER-SS.31 R FLAT WRT TYPE CAP SCR-SS.31-18X 1.00 HH NUT-SS HEX NYLOC BRACKET-MTG DEUTSCH CONNECTOR CAP SCR-SS.25-20X.75 HH GR NUT-SS NYLOC WASHER-SS.25 R WRT OD CAP SCR-SS.25-20X 1.25 HH LIGHT-CLEAR RED 30200R SCR-MACH #10-24X.75 RDH PH ZINC NUT HEX NYLOCK WASHER.19 W FLAT ANSI B27.2Z NUT-METRIC 6MM X 1.00 REF SEAL-PKRD WP/MP 16 GA GREEN TERM-PKRD WEATHERPACK 14-16GA MALE CONN-PKRD WEATHERPACK 1 CAV 1 MALE/SHROUD CAP SCR-SS.38-16X 1.25 HH WASHER-SS.38 FLAT WASHER.38 LOCK ZINC NUT-SS HEX NYLOC 2 REV. A

152 150 Dominator 2 Parts & Specifications Manual Part # Electrical Panel ( ) , , NOT POLARITY SENSITIVE CONNECTIONS FROM HARNESS (#10) CONNECTIONS FROM HARNESS (#10) CJ-905 CJ-906 CJ-907 CJ-908 CJ-910 CJ-911 TETHER CONNECTION FOR RADIO REMOTE CJ-901 CJ-902 CJ-903 CJ M1 W1 W2 W3 W4 W5 W6 CJ-909

153 Chapter 10 Electrical Options & Installation PARTS LIST ITEM PART # DESCRIPTION QUANTITY ELECTRICAL PANEL DECAL-ELECTRICAL CONTROL PANEL DOM METER-HOUR DATCON PUSH LOCK 3 MOUNTING SWITCH-ROCKER MTG PANEL END SWITCH-ROCKER MTG PANEL MIDDLE SWITCH-ROCKER BODY SWITCH-ROCKER GREEN ACTUATOR SWITCH-ROCKER SINGLE MOUNTING 3 PANEL SWITCH-ROCKER ACTUATOR - FROM A/R STABILIZER KIT HARNESS DOM POWER PANEL GROMMET-2 X 6 OVAL CMPT LIGHT LIGHT-COMPARTMENT LED (WAS ) SWITCH-ROCKER BODY MOMENTARY - A/R FROM STAB KIT SWITCH-ROCKER PLUG WASHER-SS 10 WRT TYPE SCR-MACH # 8-32X.75 RDH TIES-PLASTIC.18W 12.00L BLACK 10 REV. A

154 152 Chassis Electrical Installation ( ) (Eff ) IF WIRE BETWEEN POWER MODULE (#5) AND BATTERY IS OVER 24", INSTALL PARTS #19 & 20 IN-LINE, AS CLOSE TO THE BATTERY AS POSSIBLE. EXTRA QTY OF HDWE AND BRACKET (#51) SUPPLIED FOR MOUNTING AS NECESSARY: RECOMMENDED ORIENTATION OF COMPONENTS IS SHOWN LEFT POST: PASS THROUGH (FUSED) RIGHT POST: SWITCHED THRU RELAY (FUSED) PARTS LIST USE HEAT SHRINK (#45) OVER THESE CONNECTIONS ITEM PART # DESCRIPTION QUANTITY BRACKET-EFM CAP SCR.25-20X.88 HH GR5 Z WASHER.25 FLAT NUT HEX NYLOCK RELAY-12 VOLT POWER RELAY MODULE FUSE-FMX 30 AMP PINK FUSE-FMX 40 AMP GREEN FUSE-FMX 20 AMP BLUE FUSE-FMX 60 AMP YELLOW CONNECTOR - 2 CAV FEMALE SCR-MACH.25-20X 2.00 RDH ZINC NUT 8-32 HEX NYLOCK WASHER-SS 10 WRT TYPE KIT-EFM (ENGINE FUNCTION MODULE) 1

155 Electrical Options & Installation PARTS LIST ITEM PART # DESCRIPTION QUANTITY SCR-MACH # 8-32X.75 RDH RELAY-12V 30 AMP NOM/40 AMP MAX TERM-RING I.25 STUD GA TERM-RING NI.25 STUD 8 WIRE FUSEHOLDER-HIGH AMP2 BOLT WITH 1 COVER FUSE-AMG-125 AMP TERM-RING NI.31 STUD 6 WIRE TERM-RING NI.25 STUD 6 WIRE TERM-FEM MP AWG SEAL-MP RED CABLE SEAL TERM-FEM SLIP ON12-10/.25 TAB TERM-FSLPON I.25TAB GA KIT-DIODE DEUTSCH DT SERIES KIT-SPLICE METRIPACK 6 PIN WIRE-6 GA GXL RED A/R HARNESS DOM CHASSIS DOM HARNESS DOM CHASSIS DOM1 & DOM WIRE-14GA RED STRD TYPE GXL A/R WIRE-14GA BLACK STRD TYPE GXL A/R TUBE-HEAT SHRINK.38X 2IN DOUBLE WALL TUBE-HEAT SHRINK-1.5 INCH DUAL WALL 4FT TUBE-HEAT SHRNK.25X 6"LG (OBS) TERM-RING NI.38 STUD 6 WIRE TERM-RING.38 STUD GA WIRE-12GA WHITE STRD TYPE GXL ANGLE-AL.12X1.00X1.00X TIES-PLASTIC.18W 12.00L BLACK CABLE POWER RED #6 X 36 1 REV A

156 DRAWING POWER/RELAY MODULE - # POWER/RELAY MODULE - #5 125A 40A 20A 30A 60A AUTOMATIC SINGLE PTO (MUNCIE/CHELSEA) ALLISON MD (6000/4000) SERIES TRANSMISSION TO PTO GROUND SPLICE A TO PTO ACTIVATION CIRCUIT 12V IGNITION HOT 1 NOT USED IN THIS APPLICATION NOTE: WILL ENGAGE THE PTO AND PROVIDE A GROUND SIGNAL TO THE IMT CHASSIS ELECTRICAL WIRING WHEN THE SWITCH IS ACTIVE. THIS ALLOWS ENGINE START TO FUNCTION IF THE PRESSURE SWITCH ON THE PTO OPENS (AFTER ENGINE KILL OCCURS, FOR EXAMPLE.) BATTERY SWITCH AND LIGHT SUPPLIED WITH PTO 87 70A CHASSIS IGNITION A E-BRAKE (SWITCH SUPPLIED AS PART OF CHASSIS) CONNECTIONS TO HARNESS # INTERLOCK POWER IGNITION POWER BATTERY POWER IGNITION & E-BRAKE POWER ENGINE SPEED ENGINE STOP ENGINE START RELAY #1 RELAY #2 RELAY #3 RELAY #4 E-BRAKE IGNITION POWER 16 GROUND 87a a SEE EFM MANUAL

157 Electrical Options & Installation 155 Power Panel (Dom 1-2) ( ) CP-700 CHASSIS/BODY CONNECTOR CP-650 COMPRESSOR CONNECTOR CP-250 DEUTSCH DIODE IGN+E-BRAKE POWER R INTERLOCK POWER S IGN POWER T CMPRSR POWER U ENGINE START V ENGINE STOP W ENGINE SPEED X DUMP Y SELECTOR Z CMPRSR ON A CMPRSR POWER B GROUND C FROM PRESSURE SW D FAN GROUND E F FROM PRESSURE SW 2 ENGINE SPEED 1 S1 S2 S16 A B IGN + EBRAKE POWER INTERLOCK POWER 1 LF FLOOD 2 LR FLOOD 3 L COMPT 4 L AUX 5 RF FLOOD 6 RR FLOOD 7 R COMPT 8 R AUX 9 CRANE CMPT LIGHT 10 N/C 11 N/C 12 N/C 13 N/C 14 N/C 15 N/C 16 N/C 17 CRANE POWER 18 LEFT OUTRG U/D 19 RIGHT OUTRG U/D 20 RIGHT OUTRG I/O CJ-900 FUSE PANEL CP-100 BACKUP SIGNAL CP-850 CRANE CP-450 CRANE 2 CP-251 DEUTSCH DIODE BACKUP A SOL POWER 1 ENGINE STOP 2 GROUND 3 SPEED 4 CMPRSR ON 5 ENGINE START 6 POWER 7 8 CRANE HOUR METER 1 E-STOP SPEED 2 ENGINE SPEED 1 S4 S6 S6 S8 S6 S9 S10 S11 S12 S13 S14 S15 S6 S6 S6 S6 S17 S18 S A B S20 S20 S20 S20 S W7 CHASSIS GROUND A B W8 A B C D A B C D CHASSIS GROUND NOTE SEQUENCE CJ-200 BODY E-STOP CP-400 LEFT SIDE LIGHTING CJ-400 RIGHT SIDE LIGHTING M1 CP-401 CJ-401

158 156 Dominator 2 Parts & Specifications Manual Part # Power Panel Harness (Dom 4) ( ) CP-700 CHASSIS/BODY CONNECTOR CP-650 COMPRESSOR CONNECTOR CP-250 DEUTSCH DIODE CP-100 BACKUP SIGNAL IGN+E-BRAKE POWER R INTERLOCK POWER S IGN POWER T CMPRSR POWER U ENGINE START V ENGINE STOP W ENGINE SPEED X DUMP Y SELECTOR Z CMPRSR ON A CMPRSR POWER B GROUND C FROM PRESSURE SW D FAN GROUND E F FROM PRESSURE SW 2 ENGINE SPEED 1 BACKUP A S1 S2 S16 S6 S26 A B IGN + EBRAKE POWER INTERLOCK POWER S25 1 LF FLOOD 2 LR FLOOD 3 L COMPT 4 L AUX 5 RF FLOOD 6 RR FLOOD 7 R COMPT 8 R AUX 9 CRANE CMPT LIGHT 10 N/C 11 N/C 12 N/C 13 N/C 14 N/C 15 N/C 16 N/C 17 CRANE POWER 18 LEFT REAR I/O U/D 19 RIGHT REAR I/O U/D 20 RIGHT FRONT I/O U/D CJ-900 FUSE PANEL S24 CP-850 CRANE CP-450 CRANE 2 SOL POWER 1 ENGINE STOP 2 GROUND 3 SPEED 4 CMPRSR ON 5 ENGINE START 6 POWER 7 8 CRANE HOUR METER 1 E-STOP S4 S6 S8 S6 S9 S10 S11 S12 S13 S14 S S6 S6 S6 S6 A B 1 2 S17 S18 S19 S21 S22 S S20 S20 S20 S20 S20 S20 S20 S20 S20 S20 S S27 S27 S27 S27 S27 S27 S27 S27S27 S27 S27 S27 A B A B A B A B A B A B A B A B A B A B A B A B A B CP-251 DEUTSCH DIODE SPEED 2 ENGINE SPEED 1 W7 CHASSIS GROUND A B CJ-200 BODY E-STOP W8 CHASSIS GROUND A B C D CP-400 LEFT SIDE LIGHTING NOTE SEQUENCE A B C D CJ-400 RIGHT SIDE LIGHTING M1 OUTRIGGERS

159 157 Fuse Block, EFM, & Relay Bracket Installation ( ) (Thru ) EXTRA QUANTITY OF HARDWARE AND BRACKET SUPPLIED FOR MOUNTING AS NECESSARY. ELECTRICAL COMPONENTS ON THIS DRAWING (#5,10,16) MUST BE ORIENTED AS SHOWN FOR THEIR PROTECTION. IF WIRE BETWEEN FUSE BLOCK (#5) AND BATTERY IS OVER 24", INSTALL PARTS #19 AND #20 IN-LINE, AS CLOSE TO THE BATTERY AS POSSIBLE ,12, ,3, , 13, 15 12, 13, 15 USE HEAT SHRINK OVER THESE CONNECTIONS

160 158 Dominator 2 Parts & Specifications Manual Part # DRAWING FUSE BLOCK BATTERY A 40A 20A 30A 70A CHASSIS IGNITION A A E-BRAKE (SWITCH SUPPLIED AS PART OF CHASSIS) SEE INSERT DIAGRAM FOR AUTOMATIC APPLICATION REGARDING THIS AREA SWITCH & LIGHT SUPPLIED W/PTO CONNECTIONS TO HARNESS (#30) 4 28 INTERLOCK POWER IGNITION POWER BATTERY POWER IGNITION & E-BRAKE POWER ENGINE SPEED ENGINE STOP ENGINE START RELAY #1 RELAY #2 RELAY #3 RELAY #4 E-BRAKE IGNITION POWER GROUND a a SEE EFM MANUAL INSERT DIAGRAM: AUTOMATIC APPLICATION SINGLE PTO (MUNCIE/CHELSEA) ALLISON MD (3000/4000) SERIES TRANSMISSION DOMINATOR II (POST APRIL 2005) ONLY TO PTO GROUND SPLICE ( DOM CHASSIS ELEC INSTALLATION INSTRUCTIONS) TO PTO ACTIVATION CIRCUIT 12V IGNITION HOT A NOT USED IN THIS APPLICATION NOTE: will engage the PTO and provide a ground signal to the IMT chassis electrical wiring when the switch is active. This allows engine start to function if the pressure switch on the PTO opens (afterengine kill occurs, for example).

161 Electrical Options & Installation PARTS LIST ITEM PART # DESCRIPTION QUANTITY BRACKET-EFM CAP SCR.25-20X.88 HH GR5 Z (WAS 2) WASHER.25 FLAT NUT HEX NYLOCK (WAS 2) FUSE BLOCK-4 POS MAXI-FUSE FUSE-MAXI 70 AMP FUSE-MAXI 20 AMP FUSE-MAXI 40 AMP FUSE-MAXI 30 AMP RELAY-12V DC 75AMP SCR-MACH # 8-32X 1.00 FH PHLPS SS NUT 8-32 HEX NYLOCK WASHER-SS 10 WRT TYPE KIT-EFM (ENGINE FUNCTION MODULE) SCR-MACH # 8-32X.75 RDH RELAY-40 AMP TERMINAL - RING 6GA NUMBER 10 NON INS TERMINAL - RING 8GA NUMBER 10 NON INS FUSEHOLDER-HIGH AMP2 BOLT WITH 1 COVER FUSE-AMG-125 AMP TERMINAL - RING 6GA NUMBER 10 NON INS FERRULE - FUSE BLOCK 6 GA X 12MM FERRULE - FUSE BLOCK 12 GA X 12MM FERRULE - FUSE BLOCK 8 GA X 12MM TERM-FEM SLIP ON12-10/.25 TAB TERM-FSLPON I.25TAB GA KIT-DIODE DEUTSCH DT SERIES (WAS 2) KIT-SPLICE METRIPACK 6 PIN WIRE-6 GA GXL RED A/R HARNESS, CHASSIS (DOM 1 & 2) HARNESS, CHASSIS (DOM 4) WIRE-14GA RED STRD TYPE GXL A/R WIRE-14GA BLACK STRD TYPE GXL A/R TUBE-HEAT SHRINK 3/8X2 DOUBLE WALL TUBE-HEAT SHRINK 1.5" DUAL WALL 4' TUBE-HEAT SHRINK 1/4X TERMINAL, RING TERMINAL, RING TERMINAL, RING WIRE ANGLE TIES, PLASTIC CABLE, POWER, RED 1 REV. D

162 160 Dominator 2 Parts & Specifications Manual Part # Crane Installation Comparison If your body includes a crane, check the crane base configuration (primary or alternate) to determine floodlight installation ( ).

163 Electrical Options & Installation 161 Light Installation ( ) TERMINATE WIRES WITH #8, 9, 10. NOT POLARITY 2SENSITIVE. HARDWARE INCLUDED 4,5 1 OPTIONAL LOCATIONS ALL COMPARTMENTS EXCEPT CRANE BOX 6 DETAIL C 7 ADD 1/4" FOR DOM4 CRANE BOX 6.0" 0.5" 0.28" 0.5" (QTY 3) 1.38" 1.50" A 3 B DETAIL B C OPTIONAL LOCATIONS DETAIL A: DIMENSIONS TYPICAL BOTH SIDES -STANDARD (CRANE ROTATOR TO SIDE/FRONT) 0.5" 9.25" 0.5" A 4.63" 4.75" 0.28" (3) SEE DETAILS A & D DETAIL D: ALT. LOCATION CRANE SIDE ONLY (CRANE ROTATOR TO REAR) PARTS LIST ITEM PART # DESCRIPTION FOOT COMPT. LIGHTS 11-FOOT COMPT. LIGHTS 13 & 14- FOOT COMPT. LIGHTS 19-FOOT COMPT. LIGHTS BRACKET-FLOODLIGHT 12V REAR SP FLOODLIGHT-COMPOSITE WORK LAMP CAP SCR-SS.25-20X 1.25 HH WASHER-SS.25 W MS811 FLAT NUT-SS NYLOC LIGHT-COMPARTMENT 12V AMP SCR-SELF TAP-SS #10X.50 HH SLOT CONN-2 CAV TOWER TERM-14-16GA FEMALE CABLE SEAL-14 GA GREY REV. D FLOODLIGHT KIT (2 LIGHTS)

164 162 Dominator 2 Parts & Specifications Manual Part # By-Pass Procedure for Reverse Activated Floodlights A floodlight installed on the rear driver's side of the body will illuminate when the chassis transmission is in reverse. NOTE: Some state and local laws prohibit reverse-activated rear-facing floodlights. Consult your local and state regulations regarding reverse-activated, rear-facing floodlights. Disable if necessary. To disable, remove the relay located behind the crane box switch panel as shown. Electrical Outlet ( ) PARTS LIST ITEM PART # DESCRIPTION QUANTITY GROMMET TERMINAL-INSULATED SPADE GA CONNECTOR-1/2 STRAIN RELIEF 3/8-1/ GROUND PLUG ELECTRICAL BOX 2X44 DEEP WELL WEATHERPROOF COVER OUTLET 110V GFI 20A CABLE 14GA/3WIRE 20FT

165 Electrical Options & Installation 163 Light Reel Kits LIGHT REEL KIT - 12 VOLT ( ) LIGHT REEL KIT VOLT - LIGHT DUTY ( ) LIGHT REEL KIT VOLT W/50' CORD ( ) ITEM PART # DESCRIPTION 12 VOLT QUANTITY 110 VOLT QUANTITY REEL - 50' REEL - 50' BULB - 12V BULB - 120V 75W ROUGH SERVICE BUTT CONNECTOR TERMINAL CAP SCR 1/4-20X3 HH GR CAP SCR 5/16-18X1 HH GR NUT 1/4-20 LOCK NUT 5/16-18 HEX NYLOC SCR-MACH.25-20X.75 BTNHD ZC WIRE 14GA YELLOW X 96" WIRE 14GA WHITE X 12" WIRE 12GA/3 WIRE X 216" WASHER 5/16 FLAT VOLT QUANTITY W/CORD

166

167 165 C HAPTER 11 Miscellaneous Options In This Chapter Salvage / Plumbing Installation Kit ( ) Salvage Tank Installation, Welder in Load Bed ( ) Salvage Pump Assembly ( ) (Eff. 6-08) Antifreeze/Salvage/Water Pump ( ) (Eff ) Salvage Pump Assembly ( /Dwg ) (Thru 5-08) Headache Rack Parts & Installation ( ) Master Lock System Drawing ( ) Master Lock Kits Fuel Fill, Chevy/GMC ( )

168 166 Dominator 2 Parts & Specifications Manual Part # Salvage / Plumbing Installation Kit ( ) 3 2 7,8,9 SELECT FITTING AS NEEDED NOTE: PLUMB INTO LUBRICATED AIR ,8,9 SELECT FITTING AS NEEDED HOLE DETAIL - INSTALLATION OF SALVAGE TANK ON UNITS WITHOUT A WELDER CUTOUT 14.0" 3.50" DETAIL OF HOLE TO BE CUT IN THE FLOOR FOR THE SALVAGE TANK. USE THIS LOCATION ONLY IF THERE IS NOT A WELDER CUTOUT. 5.50" FRONT

169 Chapter 11 Miscellaneous Options PARTS LIST (DRAWING ) ITEM PART # DESCRIPTION QUANTITY 1. REF TANK-WLDMT GALLON SALVAGE TANK WELDMENT GALLON SALVAGE TANK WELDMENT TANK-WLDMT, 34 GAL SALVAGE (LOADBED) TANK-WLDMT, 60 GAL SALVAGE (LOADBED) GALLON SALVAGE KIT (W/O WELDER) GALLON SALVAGE KIT (W/O WELDER) 2. REF PUMP ASM SALVAGE SIGHT GAUGE-.75 PLUG W/REFLCT FAST FILL-VENT (ZV10) REDUCER BUSH-STL ELBOW-MPT/45/M JIC HOSE FTG-TYPE F PARK A/R HOSE FTG-TYPE J PARK A/R HOSE FTG-TYPE Z PARK A/R 10. REF FILTER-REGULATOR-LUBRICATOR TEE-STREET STL NIPPLE-BARB BRS.50MPT/90/.75 (PART OF 1 FRL) REDUCER BUSH-STL NIPPLE-BARB BRS.25MPT HOSE-HYD R PAR A/R HOSE-GP.25 X 250 WP GRAY A/R CLAMP-HOSE SAE 4 SS HYD RESERVOIR WELDMENT FLOOR, 11' RR CRANE 1 REV. A

170 168 Dominator 2 Parts & Specifications Manual Part # Salvage Tank Installation, Welder in Load Bed ( ) 4 HOLES ø 0.41" 10.0" 10.0" 2.92" SLOT RADIUS 2.50" 15.53" (34 GAL) 24.79" (60 GAL) 4.28" 5.00" 37.75" MOUNTING HOLES AND CUTOUTS FOR INSTALLATION OF SALVAGE TANK WITH WELDER IN LOADBED. NOTE: See for plumbing information.

171 Chapter 11 Miscellaneous Options 169 Salvage Pump Assembly ( ) (Eff. 6-08) 4 14 COVER WITH DECAL PARTS LIST ITEM PART # DESCRIPTION QUANTITY GAUGE-PRESS AIR 300 CNTR MNT REGULATOR-AIR FIXED VALVE-4WAY PUMP-DIAPHRAGM 1.00in METALLIC NIPPLE-PIPE BLK.12X CLOSE REDUCER BUSH-BLK COUPLING-RED BLK NIPPLE-BARB BRS.75MPT NIPPLE-BARB BRS.25MPT ADAPTER-MPT/HEX/MPT ELBOW-STREET STL.25 X 45 DEG ADAPTER-MPT/M JIC ADAPTER-MPT/HEX/MPT ADAPTER-MPT/HEX/MPT CLAMP-HOSE SAE FAST FILL-SOCKET VALVE-BALL HOSE-HYDRAULIC R4 1 9

172 170 Dominator 2 Parts & Specifications Manual Part # REV. A Antifreeze/Salvage/Water Pump ( ) (Eff )

173 Chapter 11 Miscellaneous Options PARTS LIST ITEM PART # DESCRIPTION QUANTITY AIR VALVE ASSEMBLY (PART OF 30) CHECK BALL (PART OF 29) BEARING, SLEEVE 2 4. VALVE, PILOT (PART OF 30) 1 5. INTERMEDIATE 1 6. BUMPER (PART OF 30) 2 7. BUSHING (PART OF 30) 2 8. CAP, AIR INLET ASSEMBLY 1 9. CAPSCREW, 3/8-16 X CAPSCREW, HEX 5/16-18 X CAPSCREW, HEX HD, 5/16-18 X 1 1/ CAPSCREW, HEX HD 5/16-18 X 1 3/ CHAMBER, OUTER DIAPHRAGM (PART OF 29) GASKET, AIR VALVE (PART OF 30) GASKET, PILOT VALVE (PART OF 30) GASKET, AIR INLET CAP (PART OF 30) MANIFOLD, SUCTION MANIFOLD, DISCHARGE O-RING (PART OF 30) PLATE, INNER DIAPHRAGM PLATE, OUTER ACTUATOR PIN (PART OF 30) RING, RETAINER (PART OF 30) DIAPHRAGM ROD SEAL, U-CUP (PART OF 30) SEAT, CHECK BALL (PART OF 29) LOCK WASHER, 5/ FLUID REPAIR KIT (INCL. 2,14,27) REF AIR END KIT (INCL. 1,4,6,7,15-17,20,23,24,26) REF

174 172 Dominator 2 Parts & Specifications Manual Part # Salvage Pump Assembly ( /Dwg ) (Thru 5-08) ,4, PARTS LIST ITEM PART # DESCRIPTION QUANTITY VALVE-4WAY PUMP CAP SCR.31-18X 1.25 HH GR5 Z NUT HEX NYLOCK WASHER.31 FLAT ADPTR-MPT/HEX/MPT NIPPLE-BARB BRS.75MPT CLAMP-HOSE SAE ADPTR-MPT/M JIC FAST FILL-SOCKET (OS-2) ADPTR-MPT/HEX/MPT REGULATOR-AIR NIPPLE-PIPE BLK.12X CLOSE COUPLING-RED BLK GAUGE-PRESS AIR 300 CNTR MNT ELBOW-STREET STL.25 X 45 DEG HOSE-HYD R4 18" 19 18

175 Chapter 11 Miscellaneous Options PARTS LIST ITEM PART # DESCRIPTION QUANTITY VALVE-BALL NIPPLE-BARB BRS.25MPT REDUCER BUSH-BLK NEW

176 174 Dominator 2 Parts & Specifications Manual Part # Headache Rack Parts & Installation ( )

177 Chapter 11 Miscellaneous Options 175 NOTES: 1 Drill 3/8" diameter holes to fasten headache rack. 2 Item #3, headache rack end, required only with standard compartment. Used on either side. 3 Use bonded washers when attaching to sidepack PARTS LIST ITEM PART # DESCRIPTION QUANTITY 1. N/A BODY-W D2-11' R 1 L STD REF HEADACHE RACK BODY-BOLT ON A/R HEADACHE RACK END GUSSET-BOLT ON A/R CAP SCR.31-18X 1.0 HHGR5Z (WAS A/R , ) WASHER.31 FLAT (WAS ) A/R WASHER-BONDED PLTD.31 A/R NUT HEX NYLOC (WAS ) A/R REF HEADACHE RACK, DOMINATOR STANDARD RIGHT AND STANDARD LEFT REF HEADACHE RACK, DOMINATOR STANDARD LEFT AND RAISED RIGHT REF HEADACHE RACK, DOMINATOR RAISED RIGHT AND LEFT REV B REV. A

178 176 Dominator 2 Parts & Specifications Manual Part # Master Lock System Drawing ( ) AT EACH DOOR ROD LOCATION EVERY TOP END OF A DOOR ROD MUST BE NO MORE THAN 3-4 FROM A SUPPORT. A SUPPORT CAN EITHER BE A DIVIDING WALL OR A HANGER BRACKE T. 4 EACH COLLAR MUS T BE DIRECTLY ADJACENT TO A SURFACE SUCH AS A BODY PANEL OR SUPPORT BRACKET AT END OF EACH ROD C AT END OF EACH ROD & AT CENTER OF UNSUPPORTED SPAN OF 40 OR GREATER DETAIL B SCALE 0.31 : 1 1 LOCATE & DRILL THROUGH HEADER AT ASSEMBLY (HEADER NOT SHOWN) DETAIL A SCALE 0.31 : 1 B C 5 A Ø DETAIL D SCALE 1 / 2 Ø D DRILL HOLES IN SIDEPACK THROUGH ONE WALL ONLY. MIRROR AS NECESSARY FOR FRONT END OR LEFT SIDEPACK. D DETAIL C SCALE 0.31 : SEE DETAIL D FOR DRILLING INSTRUCTIONS

179 Chapter 11 Miscellaneous Options 177 MASTER LOCK SYSTEM INSTALLATION C D PARTS LIST ITEM PART # DESCRIPTION QUANTITY BRACKET-PADLOCK MASTER LOCK A/R BRACKET-ROD STOP 2.00 M LOCK A/R COLLAR-SHAFT 2 PIECE 1/2 in. A/R WASHER-SS.50 FLAT TYPE 304 A/R 5. FRONT ROD-MASTER LOCK A/R 6. REAR ROD-MASTER LOCK A/R CAP SCREW-STAINLESS STEEL.31-18X1.00 A/R TRH PHH WASHER.25 FLAT (WAS , A/R ) NUT HEX NYLOC (WAS ) A/R BRACKET-ROD HANGER A/R

180 178 Dominator 2 Parts & Specifications Manual Part # PARTS LIST CARRIAGE BOLT X 1.25 SQNK GR2 A/R (WAS ) GROMMET A/R REV. G Master Lock Kits MASTER LOCK KIT BODY DESCRIPTION # ' DOMINATOR II WITH RIGHT-FRONT RAISED, LEFT STANDARD ' DOMINATOR II WITH RIGHT AND LEFT STANDARD ' DOMINATOR II WITH RIGHT FRONT AND LEFT FRONT RAISED ' DOMINATOR II WITH ALL RAISED (DROPPED CRANE BOX) ' DOMINATOR II WITH RIGHT FRONT RAISED, LEFT ALL RAISED ' DOMINATOR II WITH RIGHT FRONT RAISED ' DOMINATOR II WITH RIGHT FRONT AND LEFT FRONT RAISED ' DOMINATOR II WITH RIGHT FRONT, ALL LEFT RAISED QUANTITY KIT # PART # DESCRIPTION DRAWING, INSTALLATION ROD- 106X COLLAR-SHAFT PIECE BRACKET PADLOCK BRACKET-ROD STOP BRACKET-ROD HANGER ROD- 10 X ROD- 43 X ROD- 60 X ROD- 95 X ROD X ROD X ROD- 145 X HARDWARE KIT HARDWARE KIT 1 1 1

181 Chapter 11 Miscellaneous Options 179 Fuel Fill, Chevy/GMC ( ) EXISTING CLAMP EXISTING ELBOW EXISTING TUBE EXISTING CLAMP FRONT OF CHASSIS PARTS LIST ITEM PART # DESCRIPTION QUANTITY ELBOW, 90 DEG FUEL HOSE 2 (RUBBER) HOSE CLAMP TUBE 1 NEW

182

183 181 C HAPTER 12 Welder Platforms In This Chapter Welder Deck, 24" Long with 2 Underbody Toolboxes ( ) Welder Deck, 35" Long with 2 Underbody Toolboxes ( ) Welder Deck, 36" Long with Flat Deck ( ) Welder Deck, 24" Long with Tall Compartment ( ) Welder Deck, 35" Long with Curbside Tall Compartment ( ) Welder Deck, 35" Long with Streetside Tall Compartment ( )

184 182 Dominator 2 Parts & Specifications Manual Part # Welder Deck, 24" Long with 2 Underbody Toolboxes ( ) 1 2 A A SECTION A-A SCALE 0.16: PARTS LIST ITEM PART # DESCRIPTION QUANTITY WELDER DECK-WLDMT 35in L UBT-R UBT LATCH ASM-3PT DOM (II) COMPRESSION TIE DOWN-BODY 4.00 FRAME ROD-THREADED X WASHER.62 FLAT NUT HEX NYLOCK ROD-DOOR 8.12 LG W/.75" OFFSET 4 NEW

185 Chapter 12 Welder Platforms 183 Welder Deck, 35" Long with 2 Underbody Toolboxes ( ) 1 2 B C A B C A SECTION A-A SCALE 0.16:1 7 7 VIEW: INSIDE UBTB VIEW C-C SCALE 0.16: PART LIST ITEM PART # DESCRIPTION QUANTITY WELDER DECK-WLDMT 35in L UBT-R UBT LATCH ASM-3PT DOM (II) COMPRESSION TIE DOWN-BODY 4.00 FRAME ROD-THREADED X WASHER.62 FLAT NUT HEX NYLOCK ROD-DOOR 8.12 LG W/.75" OFFSET 4 NEW Welder Deck, 36" Long with Flat Deck ( ) PARTS LIST

186 184 Dominator 2 Parts & Specifications Manual Part # ITEM PART # DESCRIPTION QUANTITY HARNESS-LUBE FRONT MARKER LIGHTS HARDWARE KIT WELDER DECK, 36" FLAT TIE DOWN THREADED ROD, X 14 4

187 Chapter 12 Welder Platforms 185 Welder Deck, 24" Long with Tall Compartment ( ) 17 A A SECTION A-A SCALE 0.12:1 13 FOR CLARITY, COMPARTMENT TOP, FLOOR, DOORS NOT SHOWN PARTS LIST ITEM PART # DESCRIPTION QUANTITY REF D(II)-WELDER DECK-W D2 24in L RSD-R UBT INCL PANEL WELDER DECK UBTB RF # PANEL WELDER DECK UBTB RF # CHANNEL-FORM 1.24X 4.00X PANEL-WELDERDECK LF 60H # PANEL-WELDERDECK LF 60H # DOOR STOP-SELF CLOSING SPRING GUSSET-FRONT PANEL RH BTTM D GUSSET-FRONT PANEL LH BTTM D HINGE-SS 10GA BUTT W/IMT LOGO OFFSET BACK-BTM WELDER DECK RF D2 24in SDPK HEADER WELDER DECK CHANNEL-FORM 1.00X 2.00X MTG BAR-WLDR DECK 24in W D(II) BACK-BTM WELDER DECK LF D2 24in TOP WELDER DECK CARGO FLOOR UBTB- 1 VERT COMPT 24in TOP-WELDER DECK RSD COMPT D2 24in DOOR-WLDMT HEM D(II) 18.88H X 20.50W ( DOOR-WLDMT HEM D(II) 56.88H X 20.50W (40 1 NEW

188 186 Dominator 2 Parts & Specifications Manual Part # Welder Deck, 35" Long with Curbside Tall Compartment ( ) B C SECTION C-C SCALE 0.12:1 C B SECTION B-B SCALE 0.12: PARTS LIST ITEM PART # DESCRIPTION QUANTITY WELDER DECK-WLDMT 35in L UBTB-R RSD LATCH ASM-3PT DOM (II) COMPRESSION ROD-THREADED X TIE DOWN-BODY 4.00 FRAME NUT HEX NYLOCK WASHER.62 FLAT ROD-DOOR 8.12 LG W/.75" OFFSET ROD-DOOR LG W/.75" OFFSET 2 REV. A

189 Chapter 12 Welder Platforms 187 Welder Deck, 35" Long with Streetside Tall Compartment ( ) RIGHT SIDE LEFT SIDE ITEM PART # DESCRIPTION QUANTITY WELDER DECK-WLDMT 35in L RSD-R UBT LATCH ASM-3PT DOM (II) COMPRESSION TIE DOWN-BODY 4.00 FRAME ROD-THREADED X NUT HEX NYLOCK WASHER.62 FLAT ROD-DOOR 8.12 LG W/.75" OFFSET ROD-DOOR LG W/.75" OFFSET 2

190

191 189 C HAPTER 13 Dominator Decal Examples & Placement In This Chapter Decal List Dominator and Crane Logo Placement Body Safety Decal Placement Dominator Control Decal Placement Crane Safety Decal Placement on Dominator Door Hydraulic Oil Decal Placement Fuel Tank Decal Placement Air Tank Decal Placement Stabilizer Decal Placement Reflector & Hitch Decal Placement Compressor Decal Placement

192 190 Dominator 2 Parts & Specifications Manual Part # Decal List Dominator I, II, IV, and DSC20 have many common and some unique decals. See the chart below and the decal application photos on subsequent pages for application details. ITE M DECAL PART NUMBER DESCRIPTION QUANTITY PER BODY MODEL NOTES DOMINATOR DECAL KIT 1 ALL INCLUDES ITEMS DECAL-DOMINATOR 2 ALL IDENTIFICATION DECAL-CAUTION, DON'T 1 ALL WASH/WAX DECAL-DIESEL FUEL ONLY 2 ALL FOR DIESEL ENGINES ONLY DECAL-UNLEADED GASOLINE ONLY 2 ALL FOR GASOLINE ENGINES ONLY DECAL-DANGER EXPLODING TANK 1 ALL DECAL-AIR TANK DRAIN 1 ALL DECAL-SERVICE & REPAIR 1 ALL DECAL-FUSE PANEL LAYOUT 1 DOM I & II DECAL-ELECTRICAL PANEL 1 DOM I & II DECAL-SWITCH BRACKET 1 DSC DECAL-ELECTRICAL PANEL 1 DOM IV DECAL-SWITCH PANEL 1 DOM IV MANUAL OPERATION, STABILIZER VALVEBANK (WAS PRIOR TO , FROM THRU ) MANUAL OPERATION, DOM IV STABILIZER VALVEBANK (WAS THRU ) DECAL-HITCH, RECEIVER 2000V P DECAL-HITCH, PINTLE 6000V P DECAL-CAUTION, WELDING DAMAGE 1 DOM I & II 1 DOM IV 1 DOM I & DSC 1 DOM II & IV 1 ALL BY LIGHT BOX ON REAR OF VEHICLE

193 Chapter 13 Dominator Decal Examples & Placement 191 Dominator and Crane Logo Placement Place the crane model number, item #1; IMT diamond, item #2; and Dominator ID Decal ( ), item #3; on each side of the unit as shown.

194 192 Dominator 2 Parts & Specifications Manual Part # Body Safety Decal Placement Both item # , and item # , are applied on all four sides of the carrier vehicle, so the operator can see the dangers regarding electrocution and the crane loadline from any point of crane operation.

195 Chapter 13 Dominator Decal Examples & Placement 193 Dominator Control Decal Placement Decal - Danger, Breathing Hazard Decal - Dominator Fuse Panel Decal - Dominator Electrical Panel (Dominator I and II) (Dominator IV uses Electrical Panel Decal) Decal - Manual Operation, Stabilizer (Dominator I and II) (Dominator IV uses )

196 194 Dominator 2 Parts & Specifications Manual Part # Crane Safety Decal Placement on Dominator Door

197 Chapter 13 Dominator Decal Examples & Placement 195 Hydraulic Oil Decal Placement Place , Decal-Mobil Oil Recommendations, on top of the hydraulic tank and on the right side of the fill cap. Decal must be legible from inside the load bed.

198 196 Dominator 2 Parts & Specifications Manual Part # Fuel Tank Decal Placement Note: If unleaded gas fuel tank, use decal part number

199 Air Tank Decal Placement Chapter 13 Dominator Decal Examples & Placement 197

200 198 Dominator 2 Parts & Specifications Manual Part # Stabilizer Decal Placement

201 Reflector & Hitch Decal Placement Chapter 13 Dominator Decal Examples & Placement 199

202 200 Dominator 2 Parts & Specifications Manual Part # Place four red reflector decals, , item #1, at the sides and outer edges of the tailgate as shown. Place two amber reflector decals, , item #2, at the front of the sidepacks as shown. Place the welding caution decal, , item #3, on the side of the light box at the left rear of the body. Place a hitch decal, item #4, above the hitch on the rear of the body. Typically, Dominator I, II and DSC use Receiver Hitch, 2000 lb tongue and 16,000 lb gross trailer weight. Typically, Dominator II and IV use Pintle Hitch, 6000 lb tongue and 30,000 lb gross trailer weight.

203 Chapter 13 Dominator Decal Examples & Placement 201 Compressor Decal Placement Decal placement on a CAS435HA compressor:

204 202 Dominator 2 Parts & Specifications Manual Part # Decal placement on a CAS3560 compressor: Note: All decals for the CAS3560 air compressor are included on decal sheet See the CAS3560 manual for complete decal placement information