DUMP BODY SPREADERS INSTALLATION INSTRUCTIONS

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "DUMP BODY SPREADERS INSTALLATION INSTRUCTIONS"

Transcription

1 DUMP BODY SPREADERS INSTALLATION INSTRUCTIONS (Includes PS350 & PS400) EFFECTIVE 09/2011 Revision A TH AVE SW CEDAR RAPIDS, IA PHONE (319) FAX (319) Copyright 2009 Highway Equipment Company, Inc.

2 table of Contents HI-WAY Table header of Contents Recommended Installation... 3 Hydraulics... 4 Truck Requirements... 4 Lifting PS PS350 with Underbody Hoist... 5 Truck Preparation... 5 Hoist... 6 Dump Body... 7 Body Props... 8 Decals... 8 Mounting of Body with Telescopic Hoist... 9 Hinge... 9 Mounting Pads Cradle & Hoist Cylinder to Truck Mounting Dump Body Body Props Hoist Cylinder to Dump Body Decals Cab Shield PS350 with Underbody Hoist Option Body with Telescopic Hoist Option Inspection Ladder Storage Body-Up Indicator Side Boards Mudflaps Coal Chute Tailgate Air Kit Lights Hydraulic Hose Hose Installation Guide Frame Mount Reservoir Filling Hydraulic System Checking Installation

3 I n stallation i n stallation Instructions Hi-Way Installation Instructions Recommended sequence of installation: 1. Hinge, if applicable 6. Decals 2. Cradle, if applicable 7. Options* 3. Hoist Underbody or Cylinder 8. Hydraulics 4. Dump Body 9. Lights 5. Body Props * The cab shield may be installed before the dump body is mounted on the truck for easier access. HYDRAULICS Hydraulic System Requirements FLOW REQUIREMENTS PUMP TYPE 20 GPM (76 LPM) Gear or load sense PUMP PRESSURE CONTROL TYPE FILTRATION RESERVOIR RELIEF VALVE PSI ( Bar) operating Manual Electric solenoid Return line filter, 10 Micron 30 gallon (113.5 liter) frame mount with sight gauge 2000 PSI (138 Bar) at pump or control valve RECOMMENDED HOSE Pressure line 0-9 GPM (0-34 LPM).500 dia 100R1(min) 9-20 GPM (34-76 LPM).75 dia. 100R GPM ( LPM) 1.00 dia. 100R2 Return line 0-35 GPM (0-132 LPM) 1.00 dia. 100R GPM ( LPM) 1.25 dia. 100R1 Suction line 0-22 GPM (0-83 LPM) 1.50 dia. 100R GPM ( LPM) 2.00 dia. 100R4 Retracting underbody hoist with more pressure than 300 PSI (21 Bar) may cause damage to frame. UNDERBODY HOIST Relief valve for retracting PSI (7-21 Bar) Relief valve for extending 2000 PSI (138 Bar) PLOWS & ACCESSORIES Refer to manufacturer s manual. 3

4 HI-WAY TRUCK REQUIREMENTS Make sure the truck s CA/CT (Cab to Axle/Cab to Tandem) dimension and Frame Length are correct for the length of the dump body. See Dimensions & Specifications chart to match dump body with truck. Make sure the GAWR (Gross Axle Weight Rating) and GVWR (Gross Vehicle Weight Rating) are adequate to carry the fully loaded dump body. Your Hi-Way dealer can help calculate the weight distribution on each axle and the total loaded vehicle weight. LIFTING PS350 Installation Instructions Unit Length 55 MAX Figure 1 Lifting Maximum Angle from Vertical A A (Figure 6) Sling Leg Length 99 (25 mm) 10 (31 mm) 12 (37 mm) 113 (29 mm) 13 (40 mm) 120 (30 mm) (43 mm) 126 (32 mm) 15 (46 mm) 132 (34 mm) 16 (49 mm) 138 (35 mm) Attach a 4-point harness to the front lift hooks and rear corner bolsters as shown in Figure 1 DANGER Tailgate must be closed and latch locked before lifting with rear tailgate bolsters. Serious injury or death could occur if tailgate swings open and unit falls. WARNING Use only lifting devices that meet or exceed OSHA standard Never lift equipment over people. Never lift unit with material in the body. Loads may shift or fall if improperly supported, causing injury or damage to the unit. Do not remove lifting device until dump body is secured to truck. Lift with a maximum 55 angle from vertical to prevent damage to the unit (35 minimum angle from horizontal). 4

5 I n stallation Instructions Hi-Way MOUNTING PS350 WITH UNDERBODY HOIST Truck Preparation 3.00 MINIMUM Do not remove lifting devices while test fitting unit on truck. Lifting devices should not be removed until hoist and unit are both secured to truck. 1. Measure from front of unit to rear of hinge and add three inches. This is the distance from the cab to the rear of truck frame. 2. Mark this distance on truck frame rail. 3. Test fit hoist sub-frame and dump body to check mark. 4. Remove hoist/unit and cut off excess truck frame /64" Figure 2 Truck Modification TEST FIT & REMOVE EXCESS FRAME 11 5/8" CENTER OF HINGE PIN TO REAR OF PS FLOOR 5

6 HI-WAY Hoist DANGER Do not install hoist cylinder at an angle. If the dump body is raised with the cylinder improperly installed, the truck could tip causing serious injury or death. Do not puncture gas tank or harm any other obstruction when drilling holes. Do not leave raised body unattended. Do not raise body on unlevel ground. Check for overhead power lines and other obstructions before raising body. Installation Instructions CAB LOCATE MOUNT PLATES AT HOIST CROSS SUPPORTS TRUCK RAIL 3.00 MINIMUM 2.00 MINIMUM 2.00 MINIMUM 90 Figure 3 Hoist Position LOCATE REAR MOUNT PLATES UNDER HINGE X FIELD DRILL BOTH SIDES Figure 4 Hoist Mounting 90 Make sure hoist subframe is square with the truck cab and rails and that the hoist cylinder is centered from side-to-side on the truck chassis. DO NOT PUT HOLES IN TOP OR BOTTOM FLANGES to do so may void truck m a n u f a c t u r e r s warranty. Drill only through vertical web portions of truck frame, a minimum of 2.00 (5.08 cm) from the top or bottom flanges. Do not weld directly to truck frame. Such welding could lead to fatigue cracking and must be avoided. Connect arc welder s ground directly to one of the two items being welded before using welder on anything connected to the vehicle. 6

7 I n stallation Instructions Hi-Way 1. Place hoist on truck frame, centered as shown in Figure Center front and center Mounting Plates at ends of hoist cross supports as shown in Figure 4 and mark hole locations. Position rear Mount Plates directly under rear hinge and mark holes. 3. Drill 21/32 (1.67 cm) holes as required. Use existing holes if possible. 4. Install Mounting Plates on truck frame using 5/8 hardware provided. 5. Weld Mounting Plates to hoist sub-frame rails as shown in Figure Attach hydraulic hoses to hoist cylinder ports. Make sure hoist functions properly. Dump Body LINE UP ARMS & INSTALL PINS 2X Figure 5 Dump Body Mounting Do not remove lifting device until dump body is completely welded and body props are operational. Make sure the dump body is securely anchored and will not shift or slide off truck. Periodically check welds and mounting hardware to make sure it is secure. 1. Make sure the hoist sub-frame is properly positioned and attached to the truck frame. 2. Lift dump body onto hoist and position at least 3 (7.62 cm) from the truck cab and centered from side-to-side. Make sure the dump body sills are directly over the sub-frame rails. 3. Weld rear hinge blocks to the dump body sills. 4. Align hoist arm upper pivot holes with dump body hinge holes and insert pins. 7

8 HI-WAY Body Props DANGER Do not work beneath dump body without body props in place. Serious injury or death could occur from crushing. Make sure dump body is securely anchored and will not shift or slide off truck. Periodically check welds and mounting hardware to make sure it is secure. BODY PROP Installation Instructions Figure 6 Body Prop Alignment Place on body props by doing the following: 1. Make sure tailgate latch is open. Raise dump body with hydraulic power. 2. Lift body props and set against tabs as shown in Figure Slowly lower dump body so upper hinge angle of dump body rests on body props. Remove body props by raising dump body enough that body props are free of upper hinge angle. Lower body props and set on sub-frame tabs. Decals Some safety decals are shipped loose and must be installed by the dealer before operation of the PS. Install safety decals as required per Decals parts list and illustration in operator s manual. Install Danger, Crushing Hazard decals (PN 96704) on front of both truck frame rails, in clear view. Install Caution, Operation Safety (PN 96716) and Caution, Raised Body (PN 96715) decals in clear view in truck cab. 8

9 I n stallation Instructions Hi-Way MOUNTING OF BODY WITH TELESCOPIC HOIST Hinge Connect arc welder s ground directly to one of the two items being welded before using welder on anything connected to the vehicle. Do not exceed 300 F (148 C) at Greaseless Hinge Bushings (optional). Heat can distort Hinge Bushings. Contact Hi-Way Genuine Parts dealer for replacements if Bushings are damaged. BOTH TRUCK FRAME RAILS DO NOT WELD TO TRUCK FRAME! BOTH TRUCK FRAME RAILS DO NOT WELD TO TRUCK FRAME! 4.50 W/ PADS 5.00 W/O PADS EVEN WITH MOUNT SURFACE 4.00 Figure 7A PS350 Hinge Installation EVEN WITH MOUNT SURFACE 6.00 W/ PADS 6.50 W/O PADS 8.00 Figure 7B PS400 Hinge Installation HINGE BLOCK 5.00 HINGE BUSHING HINGE ANGLE HINGE BLOCK 6.50 HINGE BUSHING HINGE ANGLE 1. Measure from front of unit to rear of bottom sill and add 4 (10.16 cm). This is the distance from the cab to the rear of the hinge. 2. Mark this distance on truck frame rail. 3. Test fit unit to make sure there is a minimum of 4 (10.16 cm) clearance between dump body and truck cab as shown in Figure 10. Figure 13 shows position of dump body in respect to hinge/truck frame. 4. Cut truck frame so Hinge Block will be even with rear and level with mounting surface as shown in Figures 7A-7B. 5. Place Hinge Angle in cutout and center from side-toside. 6. Make sure top of Hinge Block will be level with top of Mount Pads (1, Figure 8), or truck frame if mounting directly to frame. 7. Tack weld Hinge Angle to both truck frame rails. 9

10 HI-WAY Mounting Pads (Optional) 1. Cover both truck frame rails completely with Mount Pads (1) as shown in Figure 8, from the front of the rear hinge to the rear of the cradle, and cut to length as needed. This will provide even contact with the truck frame and reduce high wear points. 2. Drill or cut Mount Pads to make clearance for rivets, bolts or other obstructions so Pads lay flat. Do not weld Mount Pads directly to truck frame. Such welding could lead to fatigue cracking and must be avoided. 5" MAX FROM CRADLE TYP 22 - TYP 5" MAX FIELD DRILL FROM HINGE Installation Instructions 2" MIN SECTION VIEW Parts needed: ITEM DESCRIPTION QTY 1 Mount Pad AR 2 Mount Angle AR 3 Cap Screw 3/8 x 1-1/4 AR 4 Lock Washer 3/8 AR 5 Hex Nut 3/8 AR AR As Required TYP..125 Figure 8 Mounting Pads 1 TRIM RUBBER TO WELD MOUNT ANGLES TO MOUNT PAD'S METAL BASE 3. Trim rubber from Mount Pads (1) so Mount Angles (2) can be welded on without damaging rubber. 4. Position Mount Angles (2) on Mount Pads (1) as shown in Figure 8 and mark hole locations on truck frame. NOTE: The rear Mount Angle should be no more than 5 (12.7 cm) from the rear hinge and the front Mount Angle should be no more than 5 (12.7 cm) from the cradle. DO NOT PUT HOLES IN TOP OR BOTTOM FLANGES to do so may void truck manufacturer s warranty. Drill only through vertical web portions of truck frame, a minimum of 2.00 (5.08 cm) from the top or bottom flanges. 5. Drill 7/16 (1.11 cm) holes. 6. Install Mount Angles using 3/8 hardware (3, 4 & 5). 7. Weld Mount Angles (2) to metal base of Mount Pads (1) as shown in Figure 8. 10

11 I n stallation Instructions Hi-Way Cradle & Hoist Cylinder to Truck BODY SIZE A (Figure 9) (CRADLE FRONT TO HINGE FRONT) 10 (31 mm) (27 mm) 12 (37 mm) (33 mm) 13 (40 mm) (36 mm) 14 (43 mm) (39 mm) 15 (46 mm) (42 mm) 16 (49 mm) (451 cm) HINGE A B Parts needed: ITEM DESCRIPTION QTY 1 Cradle 1 2 Angle 2 3 Cap Screw 5/8 x 2 GR Lock Washer 5/8 8 5 Hex Nut 5/8 GR Hoist Cylinder 1 7 Lower Cap Block 2 8 Upper Cap Block 2 9 Grease Zerk 4 10 Cap Screw 1/2 x 3-3/ Lock Washer 1/2 8 C D NOTE: Cradle will extend 1.5 (3.81 cm) beyond front of body headsheet. See Figure 10 for Items 1 5. CRADLE See Figure 11 for Items Center Cradle (1) on truck frame rails as CAB shown in Figures 9 & 10, and distance from Hinge according to chart above. Figure 9 Hinge/Cradle Square 2. Make sure hinge and cradle are square by measuring from center of hinge pins to center of cradle pins as shown in Figure 9. Distance A must equal B and distance C must equal D. 3. Center Angles (2) under Cradle and mark center of eight holes on truck rails. 4. Drill 11/16 (1.75 cm) holes where marked. 5. Attach Angles to truck with 5/8 hardware (3, 4 & 5). 11

12 HI-WAY DO NOT PUT HOLES IN TOP OR BOTTOM FLANGES to do so may void truck manufacturer s warranty. Drill only through vertical web portions of truck frame, a minimum of 2.00 (5.08 cm) from the top or bottom flanges. Make sure Cradle is square with truck cab and rails and Hoist Cylinder (6) will be centered from side-to-side on truck chassis and vertical when dump body is down. See Figures 9 & 11. Do not weld directly to truck frame. Such welding could lead to fatigue cracking and must be avoided. Connect arc welder s ground directly to one of the two items being welded before using welder on anything connected to the vehicle. 6. Tack weld Cradle to Angles as shown in Figure 10. Installation Instructions HOIST CYLINDER CENTERLINE " MINIMUM 2 2X "-8X FIELD DRILL SECTION CUT AWAY TO SHOW UPPER CYLINDER MOUNT Figure 10 Cradle Installation A 2X 2X 12

13 I n stallation Instructions Hi-Way SECTION VIEW TOP VIEW 90 7 FRONT VIEW Figure 11 Hoist Cylinder Installation DANGER Do not install hoist cylinder at an angle. If dump body is raised with the cylinder improperly installed, the truck could tip causing serious injury or death. Do not leave raised body unattended. Do not raise body on unlevel ground. Check for overhead power lines and other obstructions before raising body. Make sure dump body is securely anchored and will not shift or slide off truck. Periodically check welds and mounting hardware to make sure it is secure. 7. Restrain cylinder s lower and upper trunnion pins together before lifting so cylinder will not extend. Crimped steel banding may be used. 8. Lift Hoist Cylinder (6) with a suitable lifting device, and place in Cradle (1) as shown in Figure 11 with hydraulic ports facing truck cab. Remove trunnion restraints. Place cylinder s lower trunnion pin in cradle s cylinder block. 9. Place Lower Cap Blocks (7) over trunnion pins and secure with 1/2 (1.27 cm) hardware (10 & 11). Torque as required. 10. Install Grease Zerks (9). 11. Lean Hoist Cylinder against truck cab to mount dump body and install body props. 13

14 HI-WAY Mounting Dump Body 1. Make sure there is adequate clearance for the hoist if the cab shield has been installed. See Cab Shield Installation for cutout instructions if necessary. 2. See Lifting PS350 in Installation Instructions before lifting unit onto truck. 3. Center unit from side-to-side with rear of hinge block 7 (17.8 cm) from rear of dump body as shown in Figure 12. BOTH SILLS.313 Do not remove lifting device until hoist cylinder is secured to dump body. 7.0 Installation Instructions Body Props Figure 12 Mounting Dump Body DANGER Figure 13 Install Body Props (1) on cradle with 3/4 hardware (2 & 3). Insert non-threaded end of Latch Pins (5) through Body Props, with bend to inside, and secure with Cotter Pins (6). Place Flange Nut (4) on threaded end of Latch Pin. Do not remove lifting device until dump body is completely welded and body props are operational. Make sure dump body is securely anchored and will not shift or slide off truck. Periodically check welds and mounting hardware to make sure it is secure. Do not work beneath dump body without body props in place. Serious injury or death could occur from crushing. Parts needed: ITEM DESCRIPTION QTY 1 Body Prop 2 2 Cap Screw 3/4 x Lock Nut 3/4 2 4 Flange Nut 1/4 2 5 Latch Pin 2 6 Cotter Pin Figure 13 Body Prop 14

15 I n stallation Instructions Hi-Way Place on body props by doing the following: 1. Make sure tailgate latch is open. Raise dump body with hydraulic power. 2. Lift body props and place latch pins in slot at front of hinge. 3. Tighten or loosen flange nut to position body prop under bracket as shown in Figure Slowly lower dump body so body props rest inside brackets. Remove body props by raising dump body enough that body props are free of bracket. Pull latch pin from hinge. Lower body props. Hoist Cylinder to Dump Body (Figure 11) 1. Lift unit and place on body props. 2. Attach hydraulic hoses to Hoist Cylinder ports. 3. Carefully extend cylinder with hydraulic power. Align top trunnion pin in unit s cylinder block. 4. Place Upper Cap Blocks (8 Figure 11) over trunnion pins and secure with remaining hardware. Torque as required. 5. Install Grease Zerks (9 Figure 11). 6. Lower body. 7. Make sure cylinder is completely vertical in all directions when dump body is down (Figure 11). Adjust if necessary. Do not exceed 300 F at the Hinge Bushings. Heat can distort the Hinge Bushings. Contact Hi-Way Genuine Parts dealer for replacements if Bushings are damaged. 8. Solid weld Hinge to dump body (Figure 12) and both sides of truck frame rails (Figure 7) using full fillet welds. 9. Solid weld Cradle to Angles on truck frame rails using full fillet welds (Figure 10). Decals Install safety decals as required per Decals parts list and illustration in this manual. Install Danger, Crushing Hazard decals (PN 96704) on front of both truck frame rails, in clear view. Install Caution, Operation Safety (PN 96716) and Caution, Raised Body (PN 96715) decals in clear view in truck cab. Some safety decals are shipped loose and must be installed by the dealer before operation of the spreader. 15

16 HI-WAY CAB SHIELD (Optional) Never lift equipment over people. Use a suitable lifting device to lift the cab shield. Loads may shift or fall if improperly supported, causing injury. PS350 with Underbody Hoist Option C CAB SHIELD C L TRUCK C L MIN. CAB CLEARANCE TOP OF CAB SHIELD SHOULD BE ABOVE TOP OF HEADSHEET Installation Instructions 2-8 A B 16 /22 / A 304 UNITS ONLY B CAB HEIGHT TOP OF CAB Hoist Figure 14 Cab Shield Installation with Underbody Hoist TRUCK FRAME 1. Measure cab clearance (cab height + minimum cab clearance) as shown in Figure 14 and match to B in chart to find corresponding A dimension. 2. Determine offset of cab shield to truck centerline C (to clear obstructions such as exhaust stack). NOTE: Side of cab shield should not extend past bolster edge. 3. Lift cab shield by its lift hook, using a crane that meets or exceeds OSHA standards. Test fit by dimension A. Make any necessary modifications for proper fit. 4. Clamp cab shield in place, keeping it attached to the crane, and solid fillet weld all seams. 16

17 I n stallation Instructions Hi-Way Body with Telescopic Hoist Option D CAB SHIELD C L TRUCK C L MIN. CAB CLEARANCE TOP OF CAB SHIELD SHOULD BE ABOVE TOP OF HEADSHEET B C A CAB HEIGHT Mount pads -.50 TRUCK FRAME Figure 15 Cab Shield Installation with Telescopic Hoist PS350 B C A CAB SHIELD SIZE CAB SHIELD SIZE 16 /22 / /22 / PS400 A B C 36 / / 22 / Measure cab clearance (cab height + minimum cab clearance) as shown in Figure 15 and match to A in chart to find corresponding B dimension. 2. Determine offset of cab shield to truck centerline D (to clear obstructions such as exhaust stack). 3. Cut 15 wide by B high, offset as required. 4. Lift cab shield by its lift hook, using a crane with a minimum 1,000-pound lifting capacity. Test fit by dimension C. Make any necessary modifications for proper fit. 5. Clamp cab shield in place, keeping it attached to the crane, and solid fillet weld all seams. 17

18 HI-WAY INSPECTION LADDER (Optional) WARNING Empty and lower body, turn off all power, set vehicle brakes, lock engine starting switch and remove keys before entering body. Tag all controls to prohibit operation. Tags should be placed, and later removed, only by person working in body. Ladder is to be used for inspection purposes only. Do not use to enter dump body X 1. Position ladder on side of PS as shown in Figure Fillet weld all around the four ladder brackets. Installation Instructions Storage X Figure 16 Ladder Installation Fold bottom portion of ladder up and lock in place by hooking to top portion with rubber hooks. BODY-UP INDICATOR (Optional).50-2X If ladders are being installed on both sides, they must be offset to comply with 102 max vehicle width regulations (FHWA 49USC31113). The Body-Up Indicator has a red light that indicates when the dump body is in the raised position. Install Body-Up Indicator as shown on parts pages in the back of this manual. Make sure switch lines up with elevator bolt when body is down. Adjust bolt so switch is pressed when body is down. Raise body to test Indicator. SIDE BOARDS (Not Supplied) Wood sideboards, not provided, should be cut to length and slipped into channels on both sides of unit. Bolt sideboards in place to avoid bouncing out during operation. MUDFLAPS (Optional) Consult factory. 18

19 I n stallation Instructions Hi-Way COAL CHUTE (Optional) NOTE: A tailgate with vertical supports is required for the coal chute modification X 1. Cut opening in tailgate and through horizontal rails as shown in Figure Position coal chute on tailgate and fillet weld Figure 17 - Coal Chute Modification TAILGATE AIR KIT (Optional) Air lines recommended All ports are NPTF PORT #4 EXHAUST PORT SHALL BE PLUGGED INLET PRESSURE PORT PORT #2 EXHAUST PORT.625 MOUNTING HOLE REQUIRED OUTLET PRESSURE PORT WHEN KNOB IS DOWN SHALL BE PLUGGED OUTLET PRESSURE PORT WHEN KNOB IS UP Mount Tailgate Air Valve with knob in truck cab. Determine air supply source air manifold block or air tank. Make sure truck air brake system remains secure. Route lines from outlet pressure port on valve to air chamber. Install an air safety control valve, if necessary, into the supply port and connect the line to the valve inlet. Place cable ties as needed to keep air lines away from hot or moving parts. Check for leaks and proper operation. Figure 18 Tailgate Air Valve 19

20 HI-WAY LIGHTS (Optional) Installation Instructions Parts Needed: ITEM DESCRIPTION QTY The following is only an example. Make sure light installation 1 Red Oval Light 2 complies with all applicable requirements prescribed by FMVSS/ CMVSS 108, state and local regulations. 2 Yellow Oval Light 2 3 Red Round Light 5 See Lights parts list for installation illustration. 4 Oval Grommet 4 5 Round Grommet 5 Mount 3-Light Bar (15) on rear of truck frame as required. 6 Yellow Reflector 2 Mount Junction Box (8, not shown) on truck frame. 7 Red Reflector 4 Install Lights (1, 2 & 3) with Grommets (4 & 5). Route all wiring to 8 Junction Box 1 Lights and secure. Install Compression Fittings (9 11, not shown) 9 Compression Fitting 1 in Junction Box and connect wiring. Protect all wiring looms and connections from corrosion. 10 Compression Fitting 2 11 Compression Fitting 1 NOTE: Backup and license plate lights are not included. 12 Harness 1 13 RH Harness 1 14 LH Harness Light Bar 1 HYDRAULIC HOSE All holes in the truck cab walls, floor and firewall for control wires, hoses and cables are to be grommeted, plugged and sealed to prevent entrance of engine fumes, dust, dirt, water and noise. If a threaded connection is tightened too tightly, the fitting or housing into which the fitting is placed could be distorted and an unstoppable leak could occur. Figure 19 - Hydraulic Pump Installation Determine the pressure port of the pump. Install the pressure hose into this port. Connect the suction hose to the opposite port and to the tank outlet on the reservoir. Use thread sealer on all fittings, except o-ring and JIC adapters, o-ring valves and motors, etc. Do not put thread sealer on the first three threads of the fitting. Too much on the fitting or the first three threads will force it into the oil stream where it could damage the system. 20

21 I n stallation Instructions Hi-Way HOSE Installation Guide WRONG RIGHT WRONG RIGHT 1. Use elbows and adapters in the installation to relieve strain on the assembly, and to provide easier and neater installations that are accessible for inspection and maintenance. Remember that metal end fittings cannot be considered as part of the flexible portion of the assembly. 2. Install hose runs to avoid rubbing or abrasion. Clamps are often needed to support long runs of hose or to keep hose away from moving parts. It is important that the clamps be of the correct size. A clamp that is too large will allow the hose to move in the clamp causing abrasion at this point. WRONG RIGHT WRONG RIGHT 3. In straight hose installations allow enough slack in the hose line to provide for changes in length that will occur when pressure is applied. This change in length can be from +2% to -4%. 4. Do not twist hose during installation. This can be determined by the printed layline on the hose. Pressure applied to a twisted hose can cause hose failure or loosening of the connections. WRONG RIGHT WRONG RIGHT 5. Keep hose away from hot parts. High ambient temperature will shorten hose life. If you cannot route it away from the heat source, insulate it. 6. Keep the bend radii of the hose as large as possible to avoid hose collapsing and restriction of flow. Follow catalog specs on minimum bend radii. (Used with the permission of The Weatherhead Company.) 21

22 HI-WAY Frame Mount Reservoir TRUCK CAB 3.00 CLEARANCE REQUIRED.562-4X FIELD DRILL 2.00MIN TRUCK FRAME 2.00MIN MOUNT RESERVOIR AS HIGH AS POSSIBLE. SIDE VIEW REAR VIEW Installation Instructions Parts needed: ITEM DESCRIPTION QTY 1 Reservoir 1 2 Cap Screw 1/2x 1-1/2 4 3 Washer 1/2 4 4 Lock Nut 1/2 4 Filling the Hydraulic System Figure 20 Frame Mount Reservoir The 30-gallon (113.5-liter) Frame Mount Reservoir (1) mounts on the right-hand side of the truck frame as shown in Figure 20. Find a suitable location, as high as possible, with a minimum clearance of three inches above the cap. Mark hole locations, making sure they re at least two inches from the top and bottom of the truck frame rail. Drill (9/16 ) holes and attach with 1/2 hardware (2, 3 & 4). Do not attempt to run pump without first filling hydraulic reservoir with oil and opening suction line gate valve or the pump may be ruined. Fill reservoir with hydraulic oil as specified in the Lubricant Specifications section of this manual. Be sure oil is clean, free from dirt, water, and other contaminants. Lubricate all points requiring lubrication per the Lubrication Chart in this manual. CHECKING INSTALLATION See Initial Start-Up section in the operator s manual. 22

HR-540/HR-550 HOIST Installation & Operation Manual

HR-540/HR-550 HOIST Installation & Operation Manual Website: www.tbei.com E-mail: sales@tbei.com Phone: 1-800-869-9162 Rugby 1-800-255-4345 DuraClass 1-800-533-0494 Crysteel HR-540/HR-550 HOIST Installation & Operation Manual To Be Filled In By Installer

More information

HR-520 HOIST. Installation & Operation Manual. To Be Filled In By Installer. Pump Installation And Operation Manual#: In Service Date: Dealer:

HR-520 HOIST. Installation & Operation Manual. To Be Filled In By Installer. Pump Installation And Operation Manual#: In Service Date: Dealer: Website: www.tbei.com E-mail: sales@tbei.com Phone: 1-800-869-9162 Rugby 1-800-255-4345 DuraClass 1-800-533-0494 Crysteel HR-520 HOIST Installation & Operation Manual To Be Filled In By Installer Hoist

More information

MARATHON TELESCOPIC HOIST

MARATHON TELESCOPIC HOIST Website: www.tbei.com E-mail: sales@tbei.com CRYSTEEL S MARATHON TELESCOPIC HOIST this manual must be included with the vehicle after completing the installation. Web Site E-Mail Phone (507) 726-2728 www.crysteel.com

More information

Installation Manual. LHS & LLBS Hide-A-Way Tuckunder Style

Installation Manual. LHS & LLBS Hide-A-Way Tuckunder Style Installation Manual LHS & LLBS Hide-A-Way Tuckunder Style 10900 Kenwood Road Cincinnati, OH 45242 Ph: 513-891-6210 Toll-Free: 866-539-6261 Fax: 513-891-4901 www.leymanlift.com sales@leymanlift.com LML00136-5/1/15

More information

RIGID LIFT INSTALLATION & OPERATION MANUAL MODELS: RL-B10 THRU RL-L125

RIGID LIFT INSTALLATION & OPERATION MANUAL MODELS: RL-B10 THRU RL-L125 RIGID LIFT INSTALLATION & OPERATION MANUAL MODELS: RL-B10 THRU RL-L125 THIS MANUAL IS TO BE USED IN CONJUNCTION WITH THE APPROPRIATE PUMP INSTALLATION MANUAL AND HOIST PARTS LIST. IMPORTANT FAILURE TO

More information

SL15/20-6 AND SL15/20-10 INSTALLATION INSTRUCTIONS

SL15/20-6 AND SL15/20-10 INSTALLATION INSTRUCTIONS STOWAWAY SideLoader Tailgates By THIEMAN SL15/20-6 AND SL15/20-10 INSTALLATION INSTRUCTIONS! IMPORTANT! KEEP IN VEHICLE! READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT.

More information

MODEL TB-8, TB-10, TB-12, & TB-14 TRAILER HOIST INSTALLATION AND OPERATION MANUAL

MODEL TB-8, TB-10, TB-12, & TB-14 TRAILER HOIST INSTALLATION AND OPERATION MANUAL TRUCK BODIES & EQUIPMENT INTERNATIONAL, Inc. Website: www.tbei.com E-mail: sales@tbei.com Phone: 1-800-869-9162 1-800-533-0494 090001 MODEL TB-8, TB-10, TB-12, & TB-14 TRAILER HOIST INSTALLATION AND OPERATION

More information

! Williams Machine & Tool 204 Plastic Lane Pump Serial No. Monticello, IA USA

! Williams Machine & Tool 204 Plastic Lane Pump Serial No. Monticello, IA USA NOTICE: This manual is to remain with truck after pump unit is installed. MACHINE & TOOL Hydraulic Piston Pump Units Operating, Mounting and Safety Instructions for: Model 20 Pump Model 40 Pump Model F98

More information

1500 Series Roll Off Hoist. Owner s Manual (5-06)

1500 Series Roll Off Hoist. Owner s Manual (5-06) 1500 Series Roll Off Hoist Owner s Manual (5-06) Section 1: General Information Introduction Safety Information Warranty Information Table of Contents Section 2: Operation Operating the P.T.O. Operating

More information

INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS

INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS Tarpaulin Systems Flip -N- Go / Quick Mount Flip -N- Go System INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800) CRAMARO (800) 272-6276 Plants In: Delaware, Florida, Massachusetts, Nevada, Ohio Install

More information

650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present

650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior

More information

LIFT CORP. CUSTOMER SERVICE: (562) (800) FAX: (888) Slauson Ave. Santa Fe Springs, CA TECHNICAL SERVICE: (800)

LIFT CORP. CUSTOMER SERVICE: (562) (800) FAX: (888) Slauson Ave. Santa Fe Springs, CA TECHNICAL SERVICE: (800) M-90-1 REV. B JAN. 2000 INSTALLATION MANUAL RC-2B RC-3B RC-4B RC-5B RC-6B RC-6K 11921 Slauson Avenue. Santa Fe Springs, CA. 90670 (800) 227-4116 C MAXON Lift Corp. 1999 LIFT CORP. CUSTOMER SERVICE: (562)

More information

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis. Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers

More information

650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present

650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present Installing the Base Plate 1. Examine the interior

More information

UNIT SERIAL NUMBER MANUAL NUMBER: C EFFECTIVE 03/2014

UNIT SERIAL NUMBER MANUAL NUMBER: C EFFECTIVE 03/2014 MODEL UNIT SERIAL NUMBER MANUAL NUMBER: EFFECTIVE 03/2014 1330 76TH AVE SW CEDAR RAPIDS, IA 52404-7052 PHONE (319) 363-8281 FAX (319) 286-3350 www.highwayequipment.com Copyright 2009 Highway Equipment

More information

EZ Build Assembly and Installation

EZ Build Assembly and Installation Form No. 1-1058 March 2012 EZ Build Assembly and Installation 41500 Lot Pro Diamond Edge Plow with E-72 12V Hydraulic Unit Meyer Products LLC reserves the right, under its continuing product improvement

More information

TEREX Woodsman 730 BRUSH CHIPPER

TEREX Woodsman 730 BRUSH CHIPPER Woodsman 730 BRUSH CHIPPER Parts Manual Customer Dealer S/N Frame # Date Woodsman 150 Commerce Drive, Farwell MI 486 Phone: (800) 953-553 Fax: (989) 588-487 Flipper Discharge Chute Hand Crank Belt Shield

More information

ILM16 ILM20 ILM30 ILM12AF ILM16AF ILM20AF ILM30AF

ILM16 ILM20 ILM30 ILM12AF ILM16AF ILM20AF ILM30AF ILM Series Liftgates Read Before Installing INSTALLATION MANUAL For Models: ILM12 ILM16 ILM20 ILM30 ILM12AF ILM16AF ILM20AF ILM30AF Interlift, Inc. a Subsidary of MBB Liftsystems AG 15939 Pluma Avenue

More information

SPORT/UTILITY BLADE ASSEMBLY INSTRUCTIONS

SPORT/UTILITY BLADE ASSEMBLY INSTRUCTIONS WESTERN PRODUCTS, P.O. BOX 245038, MILWAUKEE, WI 53224-9538 FORM NO. 13629 September 1, 1999 SPORT/UTILITY BLADE ASSEMBLY INSTRUCTIONS Sport/Utility Blade No. 61300 A, Q & L Box No. 61930 Hydraulics Box

More information

SECTION 1 - FRAME & ATTACHING PARTS

SECTION 1 - FRAME & ATTACHING PARTS SECTION - FRAME & ATTACHING PARTS Undercarriage Prep Installation SEE DETAIL F SEE DETAIL E 0 SEE DETAIL D 4 EXHST BRK (OPTIONAL) - BATTERY CABLE SEE DETAIL C UP GND- TO FRAME GROUND ON - BATTERY CABLE

More information

Patriot. Aluminum and Steel 5spring. Step #1 Tarp Spool with Gear Motor (Includes Instructions for Optional Wind Deflector)

Patriot. Aluminum and Steel 5spring. Step #1 Tarp Spool with Gear Motor (Includes Instructions for Optional Wind Deflector) Aluminum and Steel 5spring Qty. Component Parts Description: LONG BOX: (1) 103 Aluminum Tarp Axle (2) 98 Upper Arms with 90 Degree Elbow (2) Lower Aluminum ( 84 ) (1) Aluminum Cross Tube SMALL HARDWARE

More information

Important. Contents. Contact us:

Important. Contents. Contact us: Operator's Manual Third Edition Third Printing Important Read, understand and obey these safety rules and operating instructions before operating this machine. Only trained and authorized personnel shall

More information

Trailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains

Trailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains Trailer Parts Brake Components Axle Components Suspensions Lights & Electrical Wheels & Tires Loading Ramps Couplers & Safety Chains Trailer Jacks Fenders Dump Trailer Parts Tilt SST Parts Decal Kits Brake

More information

Regular and High Capacity PRO-CASTER Hopper Spreader Installation Instructions

Regular and High Capacity PRO-CASTER Hopper Spreader Installation Instructions Lit. No. 94867 June 1, 2002 Regular and High Capacity PRO-CASTER Hopper Spreader Installation Instructions Read this manual and engine owner,s manual before installing or operating the spreader. This manual

More information

Draper Platform Adaptation Bundle

Draper Platform Adaptation Bundle Draper Platform Adaptation Bundle 7050-Series Self-Propelled Forage Harvester 900D-Series Draper Platform RC042050 Operator s Manual Includes installation, operating, adjustment, technical, repair parts

More information

Regular and High Capacity ICE BREAKER Hopper Spreader Installation Instructions

Regular and High Capacity ICE BREAKER Hopper Spreader Installation Instructions Lit. No. 95900, Rev. 00 September 1, 2006 Regular and High Capacity ICE BREAKER Hopper Spreader Installation Instructions Read this manual and engine owner s manual before installing or operating the spreader.

More information

TDR-44, 55, 66 OWNERS MANUAL/PARTS LIST

TDR-44, 55, 66 OWNERS MANUAL/PARTS LIST TDR SERIES Railgates By THIEMAN TDR-44, 55, 66 OWNERS MANUAL/PARTS LIST! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT. NATIONAL TRUCK

More information

E-Z LIFT 2000 BMC/TMC OPERATORS MANUAL EZ90018-EZ90538 EZ90549-EZ90689

E-Z LIFT 2000 BMC/TMC OPERATORS MANUAL EZ90018-EZ90538 EZ90549-EZ90689 E-Z LIFT 2000 BMC/TMC OPERATORS MANUAL EZ90018-EZ90538 EZ90549-EZ90689 80464_E 2001 This page left intentionally blank. 80464_E 2001 President s Message The E-Z LIFT 2000 was designed and invented with

More information

MODEL JOHN DEERE 4900 SERIES L3030G4 / MULTAPPLIER

MODEL JOHN DEERE 4900 SERIES L3030G4 / MULTAPPLIER MODEL JOHN DEERE 4900 SERIES L3030G4 / MULTAPPLIER UNIT SERIAL NUMBER MULTAPPLIER SERIAL NUMBER MANUAL NUMBER: EFFECTIVE 08/2016 1330 76TH AVE SW CEDAR RAPIDS, IA 52404-7052 PHONE (319) 363-8281 FAX (319)

More information

Railgates By THIEMAN VL-30, 40, 50 OWNERS MANUAL/PARTS LIST IMPORTANT! KEEP IN VEHICLE!

Railgates By THIEMAN VL-30, 40, 50 OWNERS MANUAL/PARTS LIST IMPORTANT! KEEP IN VEHICLE! VL SERIES Railgates By THIEMAN VL-30, 40, 50 OWNERS MANUAL/PARTS LIST! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT. NATIONAL TRUCK

More information

30,000 lb. HEAVY DUTY PPF 195 POST PULLER

30,000 lb. HEAVY DUTY PPF 195 POST PULLER OPERATION, MAINTENANCE AND PARTS MANUAL 30,000 lb. HEAVY DUTY PPF 195 POST PULLER Read and understand all of the instructions and safety information in this manual before operating or servicing this piece

More information

DEMOUNTING AND MOUNTING PROCEDURES FOR TRUCK/BUS TIRES

DEMOUNTING AND MOUNTING PROCEDURES FOR TRUCK/BUS TIRES DEMOUNTING AND MOUNTING PROCEDURES FOR TRUCK/BUS TIRES WARNING TIRE AND WHEEL SERVICING CAN BE DANGEROUS AND MUST BE DONE ONLY BY TRAINED PERSONNEL USING PROPER PROCEDURES AND TOOLS. FAILURE TO READ AND

More information

BUCKET SWEEPER OPERATORS & PARTS MANUAL 2852 & 3174 SERIES

BUCKET SWEEPER OPERATORS & PARTS MANUAL 2852 & 3174 SERIES OM628 BUCKET SWEEPER OPERATORS & PARTS MANUAL 2852 & 3174 SERIES MODEL 12002-5 FOOT WIDE X 24 INCH DIAMETER (SKID-STEER) MODEL 12004-6 FOOT WIDE X 24 INCH DIAMETER (SKID-STEER) MODEL 12017-6 FOOT WIDE

More information

MODEL SUPER P Parts List

MODEL SUPER P Parts List MODEL Parts List UNIT SERIAL NUMBER MANUAL NUMBER: EFFECTIVE 05/2016 1330 76TH AVE SW CEDAR RAPIDS, IA 52404-7052 PHONE (319) 363-8281 FAX (319) 286-3350 www.highwayequipment.com Copyright 2007 Highway

More information

Assembly Instructions for A, A, A, & A

Assembly Instructions for A, A, A, & A Update Instructions Yield-Pro 1225/1625 Planter Used with: Yield-Pro 1225 Planter Yield-Pro 1625 Planter General Information! When you see this symbol, the subsequent instructions and warnings are serious

More information

DWHOIST. Drywall Hoist Assembly & Operating Instructions

DWHOIST. Drywall Hoist Assembly & Operating Instructions DWHOIST Drywall Hoist Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides important information

More information

10,000 lb. REGULAR DUTY PPF 203 POST PULLER

10,000 lb. REGULAR DUTY PPF 203 POST PULLER OPERATION, MAINTENANCE AND PARTS MANUAL 10,000 lb. REGULAR DUTY PPF 203 POST PULLER Read and understand all of the instructions and safety information in this manual before operating or servicing this

More information

AGCO L4330G4 / MultApplier Operator s Manual

AGCO L4330G4 / MultApplier Operator s Manual AGCO / MultApplier Operator s Manual UNIT SERIAL NUMBER MULTAPPLIER SERIAL NUMBER MANUAL NUMBER: EFFECTIVE 05/2016 1330 76TH AVE SW CEDAR RAPIDS, IA 52404-7052 PHONE (319) 363-8281 FAX (319) 286-3350 www.highwayequipment.com

More information

Type 2 Push-Through 37 Ton Log Splitter. Assembly Manual

Type 2 Push-Through 37 Ton Log Splitter. Assembly Manual Type 2 Push-Through 37 Ton Log Splitter Assembly Manual Refer to this manual for the following models: RS37PT-LF09PC-16-1 RS37PT-LF09EC-16-1 RS37PT-LF09EC-16-2 RS37PT-LF13EC-22-1 RS37PT-LF13EC-22-2 RS37PT-LF15EC-22-1

More information

Operating, Servicing, and Safety Manual Model # Hydraulic Bender

Operating, Servicing, and Safety Manual Model # Hydraulic Bender Operating, Servicing, and Safety Manual Model # 900 90 Hydraulic Bender CAUTION: Read and Understand These Operating, Servicing, and Safety Instructions, Before Using This Machine. 1-800-467-2464 10 Cooperative

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS TM WEIGHTLIFTER Tailgates By THIEMAN TWL 125, 16, 20 INSTALLATION INSTRUCTIONS! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT. NTEA T

More information

Parts & Installation. Slider Series Featuring The Hutch P 3 Pneumatic Pin Puller

Parts & Installation. Slider Series Featuring The Hutch P 3 Pneumatic Pin Puller The World s Leading Manufacturer Of Trailer Sliders For Over Three Decades. Slider Series Featuring The Hutch P 3 Pneumatic Pin Puller Parts & Installation Advancing the Practical Application of Suspension

More information

Post Driver Attachment

Post Driver Attachment Attachment (Shown with Optional Power Cell Rotator) Models - 600, 850 Safety Instructions This safety alert symbol indicates important safety messages in this manual. When you see this symbol, carefully

More information

MODEL G300 BRAKE BLEEDER

MODEL G300 BRAKE BLEEDER MODEL G300 BRAKE BLEEDER Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV120716 P/N: 81-0035H THIS PAGE INTENTIONALLY

More information

AUXILIARY BATTERY BOX INSTALLATION INSTRUCTIONS

AUXILIARY BATTERY BOX INSTALLATION INSTRUCTIONS AUXILIARY BATTERY BOX INSTALLATION INSTRUCTIONS The original TOMMY GATE hydraulic lift Assembling the Auxiliary Battery Box 1. Remove the cover from the auxiliary battery box by removing the two nuts and

More information

XChange Seat Service and Maintenance Guide

XChange Seat Service and Maintenance Guide XChange Seat Service and Maintenance Guide Table Of Contents Page General Information... 1 Registration Information... 1 Seat Cushion Latch... 2 Lap Shoulder Belt Replacement... 2 Sliding Buckles Replacement...

More information

1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST MUSTANG GT LONG TUBE HEADERS (M30000)

1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST MUSTANG GT LONG TUBE HEADERS (M30000) ADVANCED - Installation requires professional-type tools and advanced automotive-service skills. If you lack experience with internal engine modifications, an Advanced installation is probably beyond your

More information

Your ONE STOP Dump Body Manufacturer

Your ONE STOP Dump Body Manufacturer Please select the features in the order they appear to insure the accuracy of the design. Fax Completed Form to 450-835-7304. Your request will be transfer to a dealer near of your country. Company Name:

More information

LOAD/ANTI TWO-BLOCK INDICATOR INSTALLATION MANUAL

LOAD/ANTI TWO-BLOCK INDICATOR INSTALLATION MANUAL LOHD -985 SYSTEM LOAD INDICATOR 10400 35400 4 400 8100 1 LOAD/ANTI TWO-BLOCK INDICATOR INSTALLATION MANUAL 1 WARNING The LOHD 985 System servicing hydraulic and lattice cranes is designed to aid the fully

More information

INSTALLATION MANUAL MUD HOG REAR WHEEL DRIVE

INSTALLATION MANUAL MUD HOG REAR WHEEL DRIVE INSTALLATION MANUAL MUD HOG REAR WHEEL DRIVE For Case IH AF 7230, 8230, 9230 Combines TUTHILL DRIVE SYSTEMS MODEL NUMBERS: CNH14023 DUAL SPEED KIT FOR CASE IH AF 7230, 8230, 9230 COMBINES D106483 CNH 84378753

More information

Proudly built in the USA. Owner s Manual TC-502 Metro Hoist, Sub-Frame, and Dump Body

Proudly built in the USA. Owner s Manual TC-502 Metro Hoist, Sub-Frame, and Dump Body Proudly built in the USA Owner s Manual TC-50 Metro Hoist, Sub-Frame, and Dump Body TruckCraft Corporation Chambersburg, PA -00-755-67 Copyright c 009 TruckCraft Corporation Rev. - - /7/09 I5-059 TRUCKCRAFT

More information

Owner s Manual. SLP Hide-A-Way Tuckunder Style

Owner s Manual. SLP Hide-A-Way Tuckunder Style Owner s Manual SLP Hide-A-Way Tuckunder Style 10900 Kenwood Road Cincinnati, OH 45242 Ph: 513-891-6210 Toll-Free: 866-539-6261 Fax: 513-891-4901 www.leymanlift.com sales@leymanlift.com LML00302-2/05/15

More information

Assembly Instructions

Assembly Instructions Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-049 Cab Enclosure MULE SX 3-4 Hours WARNING Improper installation of this accessory could result in an accident causing serious

More information

CRYSTEEL S. this manual must be included with the vehicle after completing the installation.

CRYSTEEL S. this manual must be included with the vehicle after completing the installation. Website: www.tbei.com E-mail: sales@tbei.com CRYSTEEL S POWER TAILGATE this manual must be included with the vehicle after completing the installation. Web Site E-Mail Phone (507) 726-2728 www.crysteel.com

More information

Universal Mounting Kit #0820

Universal Mounting Kit #0820 Universal Mounting Kit #0820 #1200 Super 5 th (16K) #0800 Super 5 th (20.5K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer Weight (Maximum)

More information

Important. Contents. Contact us:

Important. Contents. Contact us: Operator's Manual First Edition Ninth Printing Important Read, understand and obey these safety rules and operating instructions before operating this machine. Only trained and authorized personnel shall

More information

PARTS MANUAL THIS PAGE INTENTIONALLY LEFT BLANK. Ag-Bag International, Ltd. G7000 June Appendix A

PARTS MANUAL THIS PAGE INTENTIONALLY LEFT BLANK. Ag-Bag International, Ltd. G7000 June Appendix A The parts manual is organized into groups, it is designed to make the locating of parts easier. The exploded drawings also show assembly paths. All parts listed are available from your authorized Ag-Bag

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS THESE INSTRUCTIONS COVER THE INSTALLATION OF THE FOLLOWING REAR DOORS WITH OUTSIDE CABLES AND MAXIMUM SECURITY LOCK: 3/4" and 1" DryFreight TODCOLD Insulated

More information

TE-20 & INSTALLATION MANUAL M REV. F SEPTEMBER 2015

TE-20 & INSTALLATION MANUAL M REV. F SEPTEMBER 2015 M-12-04 REV. F SEPTEMBER 2015 INSTALLATION MANUAL TE-20 & 72-150 To find maintenance & parts information for your TE-20 & 72-150 Liftgate, go to www.maxonlift.com. Click the PRODUCTS, TUK-A-WAY and TE-20

More information

400B Product Guide. Features. ASME B30.5 Imperial 85% 9,1 t (10 USt) rating. Multiple mounting configurations. 17,1 m (56 ft) three-section boom

400B Product Guide. Features. ASME B30.5 Imperial 85% 9,1 t (10 USt) rating. Multiple mounting configurations. 17,1 m (56 ft) three-section boom 4B Product Guide ASME B3.5 Imperial 85% Features 9,1 t (1 USt) rating 17,1 m (56 ft) three-section boom Multiple mounting configurations Internal anti-two block NATIONAL CRANE 4B The 4B Series delivers

More information

Railgates By THIEMAN TVL 125, TVL 16, TVL 125A, TVL 16A OWNERS MANUAL/PARTS LIST IMPORTANT! KEEP IN VEHICLE!

Railgates By THIEMAN TVL 125, TVL 16, TVL 125A, TVL 16A OWNERS MANUAL/PARTS LIST IMPORTANT! KEEP IN VEHICLE! TM TVL SERIES Railgates By THIEMAN TVL 125, TVL 16, TVL 125A, TVL 16A OWNERS MANUAL/PARTS LIST! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT.

More information

Cranes. Range Diagram and Lifting Capacity RT345-1XL 45 TON LIFTING CAPACITY RANGE DIAGRAM 33.75' - 105' BOOM

Cranes. Range Diagram and Lifting Capacity RT345-1XL 45 TON LIFTING CAPACITY RANGE DIAGRAM 33.75' - 105' BOOM Range Diagram and Lifting Capacity RT345-1XL Cranes 45 TON LIFTING CAPACITY RANGE DIAGRAM 33.75' - 105' BOOM DIMENSIONS ARE FOR LARGEST FACTORY FURNISHED HOOK BLOCK AND HOOK & BALL, WITH ANTI-TWO BLOCK

More information

Crane Systems GREER COMPANY. LALT 1151L System for Lattice Cranes. Installation and Calibration Manual. 1 of 39

Crane Systems GREER COMPANY. LALT 1151L System for Lattice Cranes. Installation and Calibration Manual. 1 of 39 LALT 1151L System for Lattice Cranes Installation and Calibration Manual 1 of 39 This manual is designed to guide the fully trained and experienced crane operator in the correct installation and calibration

More information

SNO-PRO Ford Super Duty F-250, F-350 & F Ford Super Duty F-250, F-350 (With Snow Plow Prep. Package ONLY)

SNO-PRO Ford Super Duty F-250, F-350 & F Ford Super Duty F-250, F-350 (With Snow Plow Prep. Package ONLY) SNO-PRO 000 0 Ford Super Duty F-0, F-0 & F-0 00-00 Ford Super Duty F-0, F-0 (With Snow Plow Prep. Package ONLY) Vehicle Mounting Kit: FK Revised February 0 Curtis Industries Inc. LLC, Higgins St., Worcester,

More information

INSTALLATION MANUAL RA-35 & RA-45 M REV. D SEPTEMBER 2017

INSTALLATION MANUAL RA-35 & RA-45 M REV. D SEPTEMBER 2017 M-13-01 REV. D SEPTEMBER 2017 INSTALLATION MANUAL RA-35 & RA-45 To fi nd maintenance and parts information for your RA Liftgate, go to www.maxonlift.com. Click the PRODUCTS, SLIDELIFT & RA buttons. Open

More information

INSTALLATION AND USER MANUAL

INSTALLATION AND USER MANUAL INSTALLATION AND USER MANUAL SDKIT-730 & SDKIT-734 100% Bolt-On 150 PSI Train Horn System for 2011-2015 F-250 & F-350 Super Duty P/N SDKIT-730 P/N SDKIT-734 Thank you for purchasing a Kleinn Air Horns

More information

Box Auger & 15 Sump Style Box Auger. Beginning With Serial Number D Part No

Box Auger & 15 Sump Style Box Auger. Beginning With Serial Number D Part No Box Auger 12 14 & 15 Sump Style Box Auger Beginning With Serial Number D42370100 Part No. 24394 Box Auger Introduction Foreword Your new BOX AUGER is designed and manufactured to give you years of dependable

More information

CONTENTS: Ton Hydraulic Shop Press w/ Winch Ton Hydraulic Shop Press w/ Winch OWNER'S MANUAL

CONTENTS: Ton Hydraulic Shop Press w/ Winch Ton Hydraulic Shop Press w/ Winch OWNER'S MANUAL OWNER'S MANUAL CONTENTS: Page 1 Specifications 2 Safety Information and Warranty Information 3 Parts List 4-8 Assembly Instructions 9 Procedure for Bleeding Air 10 Pump Instructions 11-12 Winch Kit List

More information

Instruction Sheet. Follower Bar. Compression Roller Assembly (Roller Ass'y/Cylinder Clevis/ Roller Ass'y)

Instruction Sheet. Follower Bar. Compression Roller Assembly (Roller Ass'y/Cylinder Clevis/ Roller Ass'y) Gardner Bender Instruction Sheet Model B400, B400D, B400L & B400DL Eegor Hydraulic Benders IMPORTANT RECEIVING INSTRUCTIONS: Visually inspect all components for shipping damage. If any shipping damage

More information

Vibrator Kit. Stainless Steel & Poly Hopper Spreaders with FLEET FLEX Electrical System

Vibrator Kit. Stainless Steel & Poly Hopper Spreaders with FLEET FLEX Electrical System October 1, 2016 Lit. No. 95098, Rev. 01 PARTS LIST Vibrator Kit Stainless Steel & Poly Hopper Spreaders with FLEET FLEX Electrical System 5 7 6 9 8 4 1 10 2 3 99504 1 Vibrator Kit Item Part Qty Description

More information

PN: 6410T0022 Rev. 8/18/2014 Revision D Albany RR300 Stainless Mechanical Install & Owner s Manual

PN: 6410T0022 Rev. 8/18/2014 Revision D Albany RR300 Stainless Mechanical Install & Owner s Manual PN: 6410T0022 Rev. 8/18/2014 Revision D Albany RR300 Stainless Mechanical Install & Owner s Manual ASSA ABLOY ENTRANCE SYSTEM. All Rights Reserved 975-A Old Norcross Road, Lawrenceville, Georgia 30046

More information

Vehicle Wiring Harness and Cab Control

Vehicle Wiring Harness and Cab Control April 15, 2016 Lit. No. 43777, Rev. 01 Vehicle Wiring Harness and Cab Control For Low Profile, Single-Stage and Two Stage Tailgate Spreaders Installation Instructions Read this document before installing

More information

V Blade Assembly...2 Power Angling Assembly...7 V plow flares. 13 Third Spring Installation..16

V Blade Assembly...2 Power Angling Assembly...7 V plow flares. 13 Third Spring Installation..16 Table of Contents Heavy Duty V Blade V Blade Assembly...2 Power Angling Assembly...7 V plow flares. 13 Third Spring Installation..16 Important note: Lift frames for this specific blade are listed below:

More information

Railgates By THIEMAN VL-30, 40, 50 PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT. HIEMAN

Railgates By THIEMAN VL-30, 40, 50 PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT. HIEMAN VL SERIES Railgates By THIEMAN VL-30, 40, 50 INSTALLATION INSTRUCTIONS! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT. NATIONAL TRUCK

More information

INSTALLATION MANUAL MODEL 1200 FULL SIZE TRUCK MODEL 1205 COMPACT SIZE TRUCK

INSTALLATION MANUAL MODEL 1200 FULL SIZE TRUCK MODEL 1205 COMPACT SIZE TRUCK INSTALLATION MANUAL MODEL 1200 FULL SIZE TRUCK MODEL 1205 COMPACT SIZE TRUCK Load capacity: Up to 800 lbs. evenly distributed. Approximate Assembly and Installation Time: 60 min. (1 hr.) depending on truck

More information

Installation Instructions

Installation Instructions 9049 Tyler Blvd. Mentor, Ohio 44060 Phone (440) 974- Fax (440) 974-0165 Toll-Free Fax 00-41-003 saltdogg.com Installation Instructions Salt Dogg Spreader Hopper Poly Electrical 1.5 cubic yards Protected

More information

Installation Instructions Models 2858, 2858A-1, 2858GL February 2009

Installation Instructions Models 2858, 2858A-1, 2858GL February 2009 Installation Instructions Models 2858, 2858A-1, 2858GL February 2009 www.donovan-ent.com Donovan Enterprises 3353 SE Gran Park Way Stuart, FL 34997 800-327-8287 Step 1 Head Assembly Installation Instructions

More information

ELIMINATOR Dump bodies

ELIMINATOR Dump bodies ELIMINATOR Dump bodies & HR SERIES HOISTS www.rugbymfg.com Eliminator Rugby MFG Built Better The Rugby Way Rugby Manufacturing is the world s leading designer and manufacturer of Class 3-5 dump bodies,

More information

Owner s Manual Gantry Cranes

Owner s Manual Gantry Cranes Owner s Manual Gantry Cranes Fixed Height Gantry Crane MODEL NUMBER: SERIAL NUMBER: CAPACITY IN TONS: Telescoping Gantry Crane Bushman Equipment, Inc. 262-790-4200, 800338-7810, Fax 262-790-4200 www.bushman.com

More information

MODEL NO & UP MODEL NO & UP MODEL NO & UP MODEL NO & UP MODEL NO.

MODEL NO & UP MODEL NO & UP MODEL NO & UP MODEL NO & UP MODEL NO. 9-0688 MODEL NO. 00-800 & UP MODEL NO. 0-800 & UP MODEL NO. 5-800 & UP MODEL NO. -800 & UP MODEL NO. 0-800 & UP SKID SPRAYER with the Centrifugal Pump FORM NO. 95-9095 SET-UP AND PARTS CATALOG SAFETY AND

More information

TDR-44, 55, 66 OWNERS MANUAL/PARTS LIST

TDR-44, 55, 66 OWNERS MANUAL/PARTS LIST TM TDR SERIES Railgates By THIEMAN TDR-44, 55, 66 OWNERS MANUAL/PARTS LIST! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT. NTEA T H E

More information

KEANE MONROE a member of the record group

KEANE MONROE a member of the record group SERIES 3000 / 3100 MICROPROCESSOR CONTROL REGULAR ARM SLIDE ARM / SLIDE ARM W/PANIC BREAKAWAY SERIES 3000 / 3100 Page 1. INDEX and OPERATOR HANDING The KM Series 3000/3100 operators have been carefully

More information

General Information. Assembly Instructions for A. Base Update 2005 Kit. Update Instructions Yield-Pro 1625 Planter

General Information. Assembly Instructions for A. Base Update 2005 Kit. Update Instructions Yield-Pro 1625 Planter Update Instructions 2004 Yield-Pro 1625 Planter Used with: General Information 2004 Yield-Pro 1625 Planter! When you see this symbol, the subsequent instructions and warnings are serious - follow without

More information

2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014

2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014 2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014 125 Industrial Drive Spearfish, SD 57783 Toll Free 888.3WHEELS w w w. l e h m a n t r i k e s. c o m UNDERSTANDING SAFETY LABELS &

More information

LPE C5 Battery Relocation Kit

LPE C5 Battery Relocation Kit LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction

More information

Airflex Air Ride Suspension System Installation Instructions

Airflex Air Ride Suspension System Installation Instructions www.dexteraxle.com Airflex Air Ride Suspension System Installation Instructions Frame Styles Tube Frame Outside Frame Dimension Outside Bracket Dimension Channel Frame Outside Frame Dimension "C" Channel

More information

PARTS MANUAL MODELS. For AST, ATU, FP-3, and SM Model Tuckunder Liftgates

PARTS MANUAL MODELS. For AST, ATU, FP-3, and SM Model Tuckunder Liftgates A N T H O N Y L I F T G A T E S, I N C. PARTS MANUAL For AST, ATU, FP-3, and SM Model Tuckunder Liftgates MODELS AST-1500-SF AST-2000-SF AST-2500-SF AST-3000-SF ASTL-1800-SF ASTL-2500-SF ATU-1800-SF ATU-2500-SF

More information

LIFT N LOAD INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800)

LIFT N LOAD INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800) LIFT N LOAD INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800) 272-6276 001-321-757-7611 www.cramarotarps.com Plants In: Delaware, Florida, Massachusetts, Nevada, Ohio, and Canada General Information

More information

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS 40142 40142 SIDE VIEW DIAGRAM Maximum Vertical Reach 207'/63,1 m Working Area 360 Degrees Lifting Capacity 80,000 lbs/36 287 kg Boom Length 142 /43,3 m Crane Weight (Standard) 40,300 lbs/18 280 kg Jib

More information

Installation Instructions

Installation Instructions Installation Instructions MX3635-01 Rev. E Models HydraSwing 40s HydraSwing 40F 4,000 lb (1,814 kg) 10-15 seconds HydraSwing 40 4,000 lb (1,814 kg) 15-20 seconds HydraSwing 40 Twin 4,000 lb (1,814 kg)/leaf

More information

INSTALLATION INSTRUCTIONS ELITE SERIES REAR BUMPER AND TIRE CARRIER Part Number: 89525/89800 Application: Jeep JK

INSTALLATION INSTRUCTIONS ELITE SERIES REAR BUMPER AND TIRE CARRIER Part Number: 89525/89800 Application: Jeep JK INSTALLATION INSTRUCTIONS ELITE SERIES REAR BUMPER AND TIRE CARRIER Part Number: 89525/89800 Application: 2007+ Jeep JK GENERAL SAFETY PRECAUTIONS Your safety, and the safety of others, is very important.

More information

INSTALLATION INSTRUCTIONS ELITE SERIES REAR BUMPER AND TIRE CARRIER Part Number: 89525/89800 Application: Jeep JK

INSTALLATION INSTRUCTIONS ELITE SERIES REAR BUMPER AND TIRE CARRIER Part Number: 89525/89800 Application: Jeep JK INSTALLATION INSTRUCTIONS ELITE SERIES REAR BUMPER AND TIRE CARRIER Part Number: 89525/89800 Application: 2007+ Jeep JK GENERAL SAFETY PRECAUTIONS Your safety, and the safety of others, is very important.

More information

This lift will not operate with the generator engaged.

This lift will not operate with the generator engaged. WARNING 40' GENIE S40 PERSONNEL BOOM LIFT Any piece of equipment can be dangerous if not operated properly. YOU are responsible for the safe operation of this equipment. The operator must carefully read

More information

JEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market

JEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market 1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter

More information

T-52. r ve Pickup Lift Mounting Instructions Chevy / GMC- Colorado/ Canyon: 2015-present. Preparing the Gate. Installing the Bolt-on Gussets

T-52. r ve Pickup Lift Mounting Instructions Chevy / GMC- Colorado/ Canyon: 2015-present. Preparing the Gate. Installing the Bolt-on Gussets Chevy / GMC- Colorado/ Canyon: 2015-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket kit (Figure 1 and Table 1). LEFT BRACKET (RIGHT

More information

OPERATIONAL INSTRUCTION OVERVIEW MAINTENANCE CHECKLIST

OPERATIONAL INSTRUCTION OVERVIEW MAINTENANCE CHECKLIST OPERATIONAL INSTRUCTION OVERVIEW Operation Both manual and electrically powered winches develop tremendous forces; therefore, all backstops must be operated by qualified personnel only to avoid structural

More information

Power Train. Chapter 5

Power Train. Chapter 5 Chapter Power Train Spefications................................................................. -3 Test Spefications........................................................ -3 Repair Spefications.......................................................

More information

M SEPTEMBER 2017

M SEPTEMBER 2017 M-17-33 SEPTEMBER 2017 To fi nd maintenance & parts information for your TE-15 or TE-20 Liftgate, go to www. maxonlift.com. Click the PRODUCTS, TUK-A-WAY and TE-15/TE-20 buttons. Open the Maintenance Manual

More information

Vehicle Wiring Harness and Cab Control

Vehicle Wiring Harness and Cab Control August 15, 2015 Lit. No. 43777, Rev. 00 Vehicle Wiring Harness and Cab Control For Low-Profile, Two-Stage Tailgate Spreaders Installation Instructions Read this document before installing the spreader.

More information

NISSAN FRONTIER 2 & 4WD AUTOMATIC & MANUAL TRANS. KING & CREW CAB MODELS 3 BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT# 40083

NISSAN FRONTIER 2 & 4WD AUTOMATIC & MANUAL TRANS. KING & CREW CAB MODELS 3 BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT# 40083 3651 N Highway 89 Chino Valley, AZ 86323 (928) 636-7080 www.p-a-g.net NISSAN FRONTIER 2 & 4WD AUTOMATIC & MANUAL TRANS. KING & CREW CAB MODELS 3 BODY LIFT KIT INSTALLATION INSTRUCTIONS 2005-2011 KIT# 40083

More information