VERSATILE THRUSTER PNEUMATIC SLIDE

Transcription

1 S, SE VERSATILE THRUSTER PNEUMATI SLIE Major enefits Offered in short or long body an be ordered with standard or oversize shafts Standard dowel pin holes for ease of mounting Several switch options 5 bore sizes Versatile unit with over 45 standard options The S version is compact and ideal for short travel in horizontal or vertical application, where slide length and weight are critical. SERIES S SERIES SE The SE version has a greater distance between bushings for longer slide travels and greater shaft stability. clear anodized aluminum body counterbored mounting holes in the body with optional dowel holes for easy mounting of slide PH Series AV cylinder for long life with a wide range of control and switch accessories oil wicks internally lubricate the guide shafts and bushings for maximum life threaded and counterbored mounting holes in the tool plate with optional dowel holes for easy attachment of tooling clear anodized aluminum tool plate choice of bearings - linear bushing (Sx) or T fluoropolymer composite (Sx, Sx) precision ground hardened guide shafts on all units for superior performance at a moderate price (Sx, Sx) oversize guide shafts are available with T for maximum rigidity and minimum deflection 2-31

2 ORERING ATA: SERIES S & SE SLIES TO ORER SPEIFY: Product, Series, Type, Three Position, Slide Size, Slide Travel, Mid-Position Travel, Tool Plate Extension, and Options. PROUT S - Slide SERIES - Short ody E - Long ody ASI MOEL THREE POSITION UNIT (specify only if needed) TOOL PLATE EXTENSION Additional distance between tool plate and bearing block in 1" increments. Leave blank if no additional extension is required. (specify only if needed) S E E x 2-1/4 x 1-1/8 x 1 SLIES WITH T OMPOSITE USHINGS TYPE SLIE SIZE SHAFT SIZE IA. YLINER ORE EFF. AREA (EXTENSION) 3/8" 1/2" (oversize) 1/2" 5/8" (oversize) 5/8" 3/4" (oversize) 3/4" 1" (oversize) 1" 1-3/8" (oversize) 3/4" 3/4" 1" 1" 1-1/8" 1-1/8" 1-3/8" 1-3/8" 2" 2" TYPE SLIES WITH LINEAR ALL USHINGS SLIE SIZE SHAFT SIZE IA. 3/8" 1/2" 5/8" 3/4" 1" YLINER ORE 3/4" 1" 1-1/8" 1-3/8" 2" EFF. AREA (EXTENSION) SLIE TRAVEL (in) SIZE SERIES - 1/4 to 12-1/4 to 14-1/4 to 18-1/4 to 18-1/4 to SIZE SERIES E - 1/4 to 16-1/4 to 18-1/4 to - 1/4 to - 1/4 to 28 Available in 1/4" increments. onsult factory for longer travel lengths. 3 POSITION SLIES Total slide travel from retract position 1 to extend position 3. MI-POSITION TRAVEL Specify for 3 position units. Travel from retract position 1 to mid-position 2. 3 POSITION ETAIL EXTEN (YL. 1 TRAVEL) MI-POSITION (YL. 2 TRAVEL) RETRAT Options may affect unit length. See dimensional pages and option information details. Refer to this product s online catalog in the product section for complete information including related dimensions and additional specifications. See link at bottom of this page A & Sizing Assistance Use PH's free online Product Sizing and A onfigurator at

3 ORERING ATA: SERIES S & SE SLIES AITIONAL OPTIONS GM GN GO G2 G3 G4 G12 SHOK ASORER OPTIONS - Provisions for Shock Absorber mounting on extension* - Provisions for Shock Absorber mounting on retraction* - Provisions for Shock Absorber mounting on extension and retraction* - Shock Absorber and 8 mm Proximity Switch Ready on extension and retraction* - Shock Absorber and 8 mm Proximity Switch Ready on extension* - Shock Absorber and 8 mm Proximity Switch Ready on retraction* - Shock Absorber and 12 mm Proximity Switch Ready on extension and retraction* G13- Shock Absorber and 12 mm Proximity Switch Ready on extension* G14- Shock Absorber and 12 mm Proximity Switch Ready on retraction* K - HushStop on extension for use with appropriate shock absorber option -Gx L - HushStop on retraction for use with appropriate shock absorber option -G x S - Shock Pads on extension for use with option -GM, -GO, -G2, -G3, -G12, or -G13 only* T - Shock Pads on retraction for use with option -GN, -GO, -G2, -G4, -G12, or -G14 only* P AR GM S P U7 E M R J GV H1 H4 H47 J1 J2 J6 PART NO OPTIONS - Port ontrols on extension and retraction* - Adjustable ushions on extension and retraction* - Ports and control needles in position 3 (180 from standard) - Solid State Magnetic Piston - Reed Switch Magnetic Piston - Shock Pads on retraction* - HushStop on retraction* - Side mounting holes in position 2 - Slide only, no cylinder - Replacement cylinder only (see note 7) - Rodlok unit preassembled (see note 7) - lose fit dowel pin holes in the tool plate - Normal fit dowel pin holes in the tool plate - Normal fit dowel pin holes in the body. lose fit dowel pin holes are standard in the body. L10 - Oversize ports (sizes & only) Q1 - orrosion resistant guide shafts V1 - Fluoro-Elastomer Seals Z1 - Electroless nickel plate on all external ferrous parts excluding piston rod, rod end, and guide shafts PROXIMITY SWITHES ESRIPTION 8 mm Inductive Proximity Switch NPN (Sink) with 2 meter able 8 mm Inductive Proximity Switch PNP (Source) with 2 meter able See Switches and Sensors section for switch details. Switches and brackets are ordered separately. SHOK PAS STANAR HUSHSTOP AR AE GG GH GI AT AS G G G GENERAL SLIE OPTIONS - Travel Adjustment and Shock Pads on retraction* - Travel Adjustment and Shock Pads on extension* - Travel Adjustment and Shock Pads on extension with provisions for Proximity Switch mounting in both directions* - Travel Adjustment and Shock Pads on retraction with provisions for Proximity Switch mounting on retract only* - Travel Adjustment and Shock Pads with provisions for Proximity Switch mounting in both directions* NOTES: 1) Shock absorbers must be ordered separately. See option pages. Shock mounting brackets must be ordered separately for -GM, -GN, and -GO option. 2) Provisions for shock absorber mounting options include shock stops mounted on the shaft, a stop collar on the opposite shaft, and threaded holes in the slide body for mounting the shock bracket. 3) For stop and travel adjustment kits see option pages or chart below. 4) J, -R and -GG options not available with tool plate extension. 5) Proximity switches and brackets must be ordered separately for -GG, -GH, -GI, -GM, -GN, or -GO options. See option pages and the Switches and Sensors section. 6) For HushStop options (AS, AT, J, K, L, G, G, & G) stop locations may vary due to compression of softer shock pad. 7) Rodlok must be ordered separately when a replacement cylinder -H4 is ordered with an -H47 unit. 8) *aution: Unit dimensions are affected by these options. You must allow for these changes. See option drawings for complete details. Shock pads come standard with the travel adjustment options and do not need to be specified separately when travel adjustment is ordered. PROXIMITY SWITH racket AN TARGET kits SLIE SIZE 8 mm SWITH SIZE 12 mm Kit contains all components for standard non-z1 unit for one direction only. 2-33

4 ENGINEERING ATA: SERIES S & SE SLIES SPEIFIATIONS OPERATING PRESSURE OPERATING TEMPERATURE TRAVEL TOLERANE TOOL PLATE EXTENSION 3-POSITION REPEATAILITY VELOITY W/OUT PORT ONTROLS WITH OPTION P LURIATION MAINTENANE SERIES S/SE 20 psi min to 150 psi max [1.4 bar min to 10 bar max] air -20 to F [-29 to + 82 ] Nominal travel, +.030/-.000 in [+.76/- 0.0 mm] +.090/-.000 [+2.3/-0.0 mm] Mid-location.030 [0.76 mm].001" [.0 mm] of original position 50 in/sec [1.3 m/sec] max., zero load at 100 psi [6.9 bar] 16 in/sec [.4 m/sec] max., zero load at 100 psi [6.9 bar] Factory lubricated for life Field repairable SIZE TYPE SHAFT IAMETER in mm ORE IAMETER EFFETIVE AREA in mm IRETION in 2 mm EXTEN RETRAT EXTEN RETRAT EXTEN RETRAT EXTEN RETRAT EXTEN RETRAT SERIES S ASE WEIGHT lb kg SERIES SE ASE WEIGHT lb kg TRAVEL WEIGHT AER lb/in kg/mm TYPIAL YNAMI LOA lb N NOTE: Thrust capacity, allowable mass and dynamic moment capacity must be considered when selecting a slide. Refer to sizing software or the product technical manual for complete sizing and selection information. TOLERANES STANAR UNIT UNIT WITH TOOL PLATE EXTENSION 3 POSITION UNIT TRAVEL +.030/-.000 TRAVEL +.090/-.000 TOOL PLATE EXTENSION.050 MI-POSITION TRAVEL.030 TOTAL TRAVEL +.030/-.000 YLINER FORE ALULATIONS Imperial F = P x A Metric F = 0.1 x P x A F = ylinder Force lbs N P = Operating Pressure psi bar A = Effective Area in 2 mm 2 (Extend or Retract) Sizing & Application Assistance Use PH's free online Product Sizing Application or view the Product Sizing atalog at:

5 IMENSIONS: SERIES S SLIES 4X Y THREA THRU FROM THIS SIE ORE FROM OPPOSITE SIE FOR Q SHS 4 L O R A + TRAVEL A S + TRAVEL U + TRAVEL GG GG 5 HH ±.002 2X * PORT A + SLIE TOTAL TRAVEL + MI-POSITION TRAVEL 3 POSITION ETAIL 3 F E 1 E L V SQ W EE 6 A & Sizing Assistance Use PH's free online Product Sizing and A onfigurator at OPTIONAL OWEL PIN HOLES SLIE OPTION J1/*** OPTION J2/J6 MOEL LOSE FIT NORMAL FIT Sxx.1884 x.0 P.1913 x.0 P Sxx.09 x.312 P.20 x.312 P Sxx.09 x.312 P.20 x.312 P Sxx.3759 x.470 P.3770 x.470 P Sxx.3759 x.500 P.3770 x.500 P G 2 ±.0005 IA FOR OWEL PIN 2X IN TOOL PLATE 2X THRU IA & ORE FOR SHS L H J X1 SHAFT IA FOR S & S UNITS X2 SHAFT IA FOR S UNITS 4X Z THREA FROM OPPOSITE SIE *** ±.0005 IAMETER FOR OWEL PIN FROM OPPOSITE SIE 2X IN OY L FF T 3 POSITION TRAVEL OPTION SLIe *FOR EAH *PORT ONTROL MOEL A USHION P SxE SxE SxE SxE SxE OPTION AERS SIZE P R/J AR/AT AE/AS GG/GN/G GH/GM/G GI/GO/G M NOTES: 1) For options P and, add to cylinder s length (Affects dimensions, A, A) 2) For options R, J, AR, AT, GN, G and GH, add between dimensions O and A, O and A 3) For options GM, AE, as, and GG, g add to dimension U 4) For options GO and GI, add half between dimensions O and A, O and A, and half to dimension U 5) See option pages For detailed option information 6) Stroke is +.030/.000 7) All dimensions are centered on designated centerline of the unit unless otherwise specified 8) Port location for Sx is not on centerline 9) *Port is #10-32 with option -P on size 10) **Tolerance is ±.0008 between close fit dowel pin holes. Tolerance is ±.001 between normal fit dowel pin holes 11) ***LOSE FIT OWEL PINS ARE STANAR IN OY 12) circled numbers indicate position ORE LETTER IMENSION SIZE SIZE A E** F G H J L M O Q R S T U 3/ #10 x.215 P #10 x.215 P / /4 x.275 P / /16 x.338 P /8 x.400 P SIZE V W X1 X2 Y Z A *** EE** FF GG HH /4-20 #10- x.37 P /8 NPT*.1884 x. P 1/ /4-20 1/4-20 x.40 P /8 NPT.09 x.31 P 5/ / /4-20 x.50 P /8 NPT.09 x.31 P 3/ /8-16 3/8-16 x.69 P /8 NPT.3759 x.47 P 3/ /2-13 3/8-16 x.75 P /4 NPT.3759 x.50 P 1/

6 IMENSIONS: SERIES SE SLIES 4X Y THREA THRU FROM THIS SIE ORE FROM OPPOSITE SIE FOR Q SHS 4 O R S E A + TRAVEL A + TRAVEL U + TRAVEL GG A + SLIE TOTAL TRAVEL + MI-POSITION TRAVEL 3 POSITION ETAIL GG 3 F E 1 E 5 L HH V SQ.002 W EE 2X * PORT 6 A & Sizing Assistance Use PH's free online Product Sizing and A onfigurator at OPTIONAL OWEL PIN HOLES SLIE OPTION J1/*** OPTION J2/J6 MOEL LOSE FIT NORMAL FIT Sxx.1884 x.0 P.1913 x.0 P Sxx.09 x.312 P.20 x.312 P Sxx.09 x.312 P.20 x.312 P Sxx.3759 x.470 P.3770 x.470 P Sxx.3759 x.500 P.3770 x.500 P 3 POSITION TRAVEL OPTION SLIe *FOR EAH *PORT ONTROL MOEL A USHION P SExE SExE SExE SExE SExE OPTION AERS SIZE P R/J AR/AT AE/AS GG/GN/G GH/GM/G GI/GO/G L G IA FOR OWEL PIN 2X IN TOOL PLATE 4X THRU IA & ORE FOR SHS L H M J ***.0005 IAMETER FOR OWEL PIN FROM OPPOSITE SIE 2X IN OY X1 SHAFT IA FOR SE & SE UNITS X2 SHAFT IA FOR SE UNITS 4X Z THREA FROM OPPOSITE SIE NOTES: 1) For options P and, add to cylinder s length (Affects dimensions, A, A) 2) For options R, J, AR, AT, GN, and GH, G add between dimensions O and A, O and A 3) For options GM, AE, AS, and GG, G add to dimension U 4) For options GO and GI, add half between dimensions O and A, O and A, and half to dimension U 5) See option pages For detailed option information 6) Stroke is +.030/.000 7) All dimensions are centered on designated centerline of the unit unless otherwise specified 8) Port location for SEx is not on centerline 9) *Port is #10-32 with option -P on size 10)**Tolerance is ±.0008 between close fit dowel pin holes, Tolerance is ±.001 between normal fit dowel pin holes 11) ***LOSE FIT OWEL PINS ARE STANAR IN OY 12) circled numbers indicate position ORE LETTER IMENSION SIZE SIZE A E** F G H J L M O Q R S T U 3/ #10 x.215 P #10 x.215 P / /4 x.275 P / /16 x.338 P /8 x.400 P L FF T SIZE V W X1 X2 Y Z A *** EE** FF GG HH /4-20 #10- x.37 P /8 NPT*.1884 x. P 1/ /4-20 1/4-20 x.40 P /8 NPT.09 x.31 P 5/ /16-181/4-20 x.50 P /8 NPT.09 x.31 P 3/ /8-16 3/8-16 x.69 P /8 NPT.3759 x.47 P 3/ /2-133/8-16 x.75 P /4 NPT.3759 x.50 P 1/

7 P The exclusive PH Port ontrol, based on the meter-out principle, features an adjustable needle and check seal. oth are built into the cylinder head and cap and are used to control the speed of the slide over its entire travel. NOTE: Port ontrols add 1/4" to the cylinder length (affects dimensions A, A, and ) on sizes,, and. E PORT ONTROL MAGNET FOR PH SOLI STATE SWITHES This option equips the cylinder with a magnetic band on the piston for use with PH 1750 Solid State Switches. M MAGNET FOR PH REE SWITHES This option equips the cylinder with a magnetic band on the piston for use with PH 1750 Reed Switches. See Switches Section at phdinc.com for specific Solid State and Reed Switch information. SWITHES MUST E ORERE SEPARATELY. J This option provides composite shock pads on retraction only, eliminating metal-to-metal contact as the tool plate reaches the slide body. This option, quieter than the R option, greatly reduces noise and shock upon slide retraction. Not available with tool plate extension. ue to the composite shock pads, stop locations may vary. For close tolerance stop locations, use R option. AR This option provides both travel adjustment stop collars and polyurethane shock pads on retraction only. The travel adjustment stop collars provide infinite adjustment while the shock pads eliminate metal-to-metal contact, thereby quieting the unit. AE HushStop SHOK PAS ON RETRATION TRAVEL AJUSTMENT AN SHOK PAS ON RETRATION TRAVEL AJUSTMENT AN SHOK PAS ON EXTENSION This option provides both travel adjustment stop collars and polyurethane shock pads on extension only. The travel adjustment stop collars provide infinite adjustment while the shock pads eliminate metal-to-metal contact, thereby quieting the unit. Options may affect unit length. See dimensional pages and option information details. U7 PORTS AN ONTROL NEELE IN POSITION 3 This option provides for the ports, Port ontrol, and cushions to be in position 3, or underside of the unit (180 from standard). AJUSTALE USHIONS PH ushions are designed for smooth deceleration at each end of travel. When the cushion is activated, the remaining volume in the cylinder must exhaust past an adjustable needle which controls the amount of deceleration. The wide adjustment range makes the cushion ideal for end of travel shock reduction. ushion needles are located on the same side as the Port ontrol needles for easy access and adjustment. NOTE: ushions add to the cylinder length (affects dimensions A, A, and ) add 1.000" on sizes,, and ; and 1.750" on size. L10 OVERSIZE PORTS (available on sizes & only) This option provides an oversized port on the head and cap of the cylinder for size and. This will then allow ports to match appropriate sized NFPA cylinder standards. Size ports become 1/4 NPT instead of 1/8 NPT. Size ports become 3/8 NPT instead of 1/4 NPT. Ports will remain in standard port locations. R SHOK PAS ON RETRATION This option provides polyurethane shock pads on retraction only, eliminating metal-to-metal contact as the tool plate reaches the slide body. This option greatly reduces noise and shock upon slide retraction. Not available with tool plate extension. AT TRAVEL AJUSTMENT AN HushStop SHOK PAS ON RETRATION This option, quieter than the AR option, provides both travel adjustment stop collars and composite shock pads on retraction only. The travel adjustment stop collars provide infinite adjustment while the shock pads eliminate metal-to-metal contact, thereby quieting the unit. ue to the composite shock pads, stop locations may vary. For close tolerance stop locations, use the AR option. AS TRAVEL AJUSTMENT AN HushStop SHOK PAS ON EXTENSION This option, quieter than the AE option, provides both travel adjustment stop collars and composite shock pads on extension only. The travel adjustment stop collars provide infinite adjustment while the shock pads eliminate metal-to-metal contact, thereby quieting the unit. ue to the composite shock pads, stop locations may vary. For close tolerance stop locations, use the AE option. Refer to this product s online catalog in the product section for complete information including related dimensions and additional specifications. See link at bottom of this page. 2-37

8 G TRAVEL AJUSTMENT AN HushStop SHOK PAS ON EXTENSION WITH PROVISIONS FOR PROXIMITY SWITH MOUNTING IN OTH IRETIONS This option, quieter than the GG option, provides both travel adjustment and composite shock pads on extension; and provisions for mounting of proximity switch targets and brackets on both ends. For close tolerance stop locations, use the GG option. G TRAVEL AJUSTMENT AN HushStop SHOK PAS ON RETRATION WITH PROVISIONS FOR PROXIMITY SWITH MOUNTING ON RETRATION This option, quieter than the GH option, provides both travel adjustment and composite shock pads on retraction and provisions for mounting of proximity switch targets and brackets in the retraction direction only. For close tolerance stop locations, use the GH option. G TRAVEL AJUSTMENTS, HushStop SHOK PAS, AN PROVISIONS FOR PROXIMITY SWITHES IN OTH IRETIONS This option,quieter than the GI option, provides both travel adjustment and composite shock pads in both directions and provisions for mounting of proximity switch targets and brackets on both ends. For close tolerance stop locations, use the GI option. Q1 ORROSION RESISTANT GUIE SHAFTS Extremely hard corrosion-resistant coating on the guide shafts for use in applications where moisture may corrode hardened ground shafts. End faces of the shafts remain uncoated. onsult PH for fully coated shafts. GG TRAVEL AJUSTMENT AN SHOK PAS ON EXTENSION WITH PROVISIONS FOR PROXIMITY SWITH MOUNTING IN OTH IRETIONS This option provides both travel adjustment and polyurethane shock pads on extension; and provisions for mounting of proximity switch targets and brackets on both ends. Not available with tool plate extension. With tool plate extension use GH option. GH TRAVEL AJUSTMENT AN SHOK PAS ON RETRATION WITH PROVISIONS FOR PROXIMITY SWITH MOUNTING ON RETRATION This option provides both travel adjustment and polyurethane shock pads on retraction and provisions for mounting of proximity switch targets and brackets in the retraction direction only. GI TRAVEL AJUSTMENTS, SHOK PAS, AN PROVISIONS FOR PROXIMITY SWITHES IN OTH IRETIONS This option provides both travel adjustment and polyurethane shock pads in both directions and provisions for mounting of proximity switch targets and brackets on both ends. V1 FLUORO-ELASTOMER SEALS Fluoro-Elastomer seals are available for seal compatibility with certain fluids. Seal compatibility should be checked with the fluid manufacturer for proper application. onsult PH for high temperature applications. Z1 ELETROLESS NIKEL PLATING This option provides electroless nickel plating on all externally exposed ferrous parts except the guide shafts and cylinder rod end. This optional plating can be used for protecting the slide from severe or corrosive environments. The guide shafts can be made corrosionresistant by specifying the -Q1 shaft option. NOTE: Shock absorbers are not plated with -Z1 option. Options may affect unit length. See dimensional pages and option information details Refer to this product s online catalog in the product section for complete information including related dimensions and additional specifications. See link at bottom of this page.

9 GM PROVISIONS FOR SHOK ASORER MOUNTING ON EXTENSION This option provides for mounting a bracket for a shock absorber in the extend direction. This includes mounting holes in the slide body, a shock stop on one shaft, and a stop collar on the other shaft. This arrangement allows the shock absorber to double as a travel adjustment in the extension direction. Shock stop and mounting bracket are supplied ready for proximity switch bracket and target mounting. GN PROVISIONS FOR SHOK ASORER MOUNTING ON RETRATION This option provides for mounting a bracket for a shock absorber in the retract direction. This includes mounting holes in the slide body, a shock stop on one shaft, and a stop collar on the other shaft. This arrangement allows the shock absorber to double as a travel adjustment in the retraction direction. Shock stop and mounting bracket are supplied ready for proximity switch bracket and target mounting. GO PROVISIONS FOR SHOK ASORER MOUNTING ON EXTENSION AN RETRATION This option provides for mounting brackets for shock absorbers in both the extend and retract direction. This includes two sets of mounting holes in the slide body, shock stops mounted on the shafts in each direction, and stop collars mounted on the opposite shafts. This arrangement allows the shock absorbers to double as travel adjustments in both directions. Shock stops and brackets are supplied ready for proximity switch bracket and target mounting. G3 G13 SHOK ASORER & PROXIMITY SWITH REAY ON EXTENSION This option provides mounting brackets for a shock absorber and proximity switch on the extension only. This includes mounting brackets for both shock absorber and proximity switch, a proximity target and mounting hardware, with a stop collar and stop on the shafts. This arrangement allows the shock absorber to double as a travel adjustment in the extension direction. G3 = 8 mm Proximity Switch G13 = 12 mm Proximity Switch G2 G12 SHOK ASORER AN PROXIMITY SWITH REAY ON EXTENSION AN RETRATION This option provides mounting brackets for shock absorbers and proximity switches in both directions. This includes mounting brackets for both shock absorbers and proximity switches, proximity targets, and mounting hardware with stop collars and stops mounted on the shafts. This arrangement allows the shock absorbers to double as travel adjustments in both directions. G2 = 8 mm proximity switch G12 = 12 mm proximity switch G4 G14 SHOK ASORER & PROXIMITY SWITH REAY ON RETRATION This option provides mounting brackets for a shock absorber and proximity switch on the retraction only. This includes mounting brackets for both shock absorber and proximity switch, shaft, a proximity target and mounting hardware, with a stop collar and stop on the other shafts. This arrangement allows the shock absorber to double as a travel adjustment in the retract direction. G4 = 8 mm Proximity Switch G14 = 12 mm Proximity Switch The shock absorber and shock mounting kit must be ordered separately. Options may affect unit length. See dimensional pages and option information details. Refer to this product s online catalog in the product section for complete information including related dimensions and additional specifications. See link at bottom of this page. 2-39

10 K HushStop SHOK PAS ON EXTENSION GV SIE MOUNTING HOLES IN POSITION 2 The -K option adds composite shock pads on extension to the -GM, -GO, -G2, -G3, -G12, or -G13 shock absorber option. The shock pads are assembled between the shock stop (stop collar) and the slide body. The purpose of this option, quieter than the -S option, is to complement the shock absorber by eliminating metal to metal contact at the end of slide extension. Shock pads do not affect length adders for shock absorber options. ue to the composite shock pads, stop locations may vary. For close tolerance stop locations, use the -S option. S SHOK PAS ON EXTENSION The -S option adds shock pads on extension to the -GM, -GO, -G2, -G3, -G12, or -G13 shock absorber option. The shock pads are assembled between the shock stop (stop collar) and the slide body. The purpose of this option is to complement the shock absorber by eliminating metal to metal contact at the end of slide extension. Shock pads do not affect length adders for shock absorber options. T SHOK PAS ON RETRATION The -T option adds shock pads on retraction to the -GN, -GO, -G2, -G4, -G12, or -G14 shock absorber option. The shock pads are assembled between the shock stop (stop collar) and the slide body. The purpose of this option is to complement the shock absorber by eliminating metal to metal contact at the end of slide retraction. Shock pads do not affect length adders for shock absorber options. L HushStop SHOK PAS ON RETRATION This option provides an additional mounting pattern on one side of the slide body. This pattern is ideal if the slide is to be mounted on edge for applications where a narrow profile is required. H47 ROLOK SLIE & ROLOK PH s Rodlok is ideal for locking the tool plate while in a static/ stationary position. When the pressure is removed from the port of the Rodlok, the mechanism will grip the piston rod of the cylinder and prevent it from moving. The loads are held indefinitely without power. Rodlok performance is application and environment sensitive (cleanliness of rod or Rodlok will also affect performance). THE ROLOK IS NOT ESIGNE TO E USE AS A PERSONNEL SAFETY EVIE. SIZE STATI LOKING FORE* lb N NOTE: *Locking force given in table is the actual locking force with a dry clean rod and does not include any safety factor. REPLAEMENT ROLOK KITS The -L option adds composite shock pads on retraction to the -GN, -GO, -G2, -G4, -G12, or -G14 shock absorber option. The shock pads are assembled between the shock stop (stop collar) and the slide body. The purpose of this option, quieter than the -T option, is to complement the shock absorber by eliminating metal to metal contact at the end of slide retraction. Shock pads do not affect length adders for shock absorber options. ue to the composite shock pads, stop locations may vary. For close tolerance stop locations, use the -T option Options may affect unit length. See dimensional pages and option information details. Refer to this product s online catalog in the product section for complete information including related dimensions and additional specifications. See link at bottom of this page. MOEL NO. Sx SEx S/SEx S/SEx S/SEx S/SEx LOKING EVIE KIT AAPTOR KIT* OMPLETE ROLOK* NOTES: 1) *Kits ship with cylinder mounting hardware. 2) Part numbers listed above are intended for replacement purposes only and are to be used specifically on slides with the -H47 option. The Rodlok locking device and adaptor can be purchased separately as kits. See chart above. The locking device and adaptor are not available with a corrosion resistant (-Z1 option) finish.

11 P PORT ONTROL The exclusive PH Port ontrol, based on the meter-out principle, features an adjustable needle and check seal. oth are built into the cylinder head and cap and are used to control the speed of the slide over its entire travel. The self-locking needle has micrometer threads and is adjustable under pressure. It determines the orifice size which controls the exhaust volume only of the cylinder proper. The check seal is closed while fluid is exhausting from the cylinder, but opens to permit full flow of incoming fluids. The PH Port ontrol provides the optimum in speed control for slides. All adjustments are made from the top surface of the slide. It saves space and eliminates the cost of installation and fittings for external flow control valves. NOTE: Port ontrols add 1/4" to the cylinder length (affects dimensions A, A, and ) on sizes,, and. MAXIMUM SLIE VELOITY S & SE SLIES 50 in/sec without Port ontrols 16 in/sec with Port ontrols The above figures are based on a working pressure of 100 psi and a no load horizontal condition. U7 PORTS AN ONTROL NEELE IN POSITION 3 This option provides for the ports, Port ontrol, and cushions to be in position 3, or underside of the unit (180 from standard) AJUSTALE USHIONS PORT ONTROL & USHION AJUSTMENT POSITIONS PORT ONTROL NEELES PH ushions are designed for smooth deceleration at each end of travel. When the cushion is activated, the remaining volume in the cylinder must exhaust past an adjustable needle which controls the amount of deceleration. The wide adjustment range makes the cushion ideal for end of travel shock reduction. ushion needles are located on the same side as the Port ontrol needles for easy access and adjustment. NOTE: ushions add to the cylinder length (affects dimensions A, A, and ) add 1.000" on sizes,, and ; and 1.750" on size. USHION ONTROL NEELES Effective cushion length 1/2" on size through and 3/4" on size. E MAGNET FOR PH SOLI STATE SWITHES This option equips the cylinder with a magnetic band on the piston for use with PH 1750 Solid State Switches. M MAGNET FOR PH REE SWITHES This option equips the cylinder with a magnetic band on the piston for use with PH 1750 Reed Switches. These cylinder-mounted switches are an easy and convenient way of interfacing the slide to various programmable controllers or logic systems. See page 2-54 for specific Solid State and Reed Switch information. SWITHES MUST E ORERE SEPARATELY

12 L10 OVERSIZE PORTS (available on sizes & only) This option provides an oversized port on the head and cap of the cylinder for size and. This will then allow ports to match appropriate sized NFPA cylinder standards. Size ports become 1/4 NPT instead of 1/8 NPT. Size ports become 3/8 NPT instead of 1/4 NPT. Ports will remain in standard port locations. R SHOK PAS ON RETRATION This option provides polyurethane shock pads on retraction only, eliminating metal-to-metal contact as the tool plate reaches the slide body. This option greatly reduces noise and shock upon slide retraction. Not available with tool plate extension..0 A TO ASI SLIE IMENSIONS J HushStop SHOK PAS ON RETRATION This option provides composite shock pads on retraction only, eliminating metal-to-metal contact as the tool plate reaches the slide body. This option, quieter than the R option, greatly reduces noise and shock upon slide retraction. Not available with tool plate extension. ue to the composite shock pads, stop locations may vary. For close tolerance stop locations, use R option..0 A TO ASI SLIE IMENSIONS AR TRAVEL AJUSTMENT AN SHOK PAS ON RETRATION This option provides both travel adjustment stop collars and polyurethane shock pads on retraction only. The travel adjustment stop collars provide infinite adjustment while the shock pads eliminate metal-to-metal contact, thereby quieting the unit..750 (,,, ) A TO ASI SLIE IMENSIONS AT TRAVEL AJUSTMENT AN HushStop SHOK PAS ON RETRATION This option, quieter than the AR option, provides both travel adjustment stop collars and composite shock pads on retraction only. The travel adjustment stop collars provide infinite adjustment while the shock pads eliminate metal-to-metal contact, thereby quieting the unit. ue to the composite shock pads, stop locations may vary. For close tolerance stop locations, use the AR option..750 (,,, ) A TO ASI SLIE IMENSIONS AE TRAVEL AJUSTMENT AN SHOK PAS ON EXTENSION This option provides both travel adjustment stop collars and polyurethane shock pads on extension only. The travel adjustment stop collars provide infinite adjustment while the shock pads eliminate metal-to-metal contact, thereby quieting the unit..750 (,,, ) A TO ASI SLIE IMENSIONS

13 AS TRAVEL AJUSTMENT AN HushStop SHOK PAS ON EXTENSION This option, quieter than the AE option, provides both travel adjustment stop collars and composite shock pads on extension only. The travel adjustment stop collars provide infinite adjustment while the shock pads eliminate metal-to-metal contact, thereby quieting the unit. ue to the composite shock pads, stop locations may vary. For close tolerance stop locations, use the AE option. KIT TYPE STANAR TRAVEL AJUSTMENT (-AR OR -AE) HushStop TRAVEL AJUSTMENT (-AT OR -AS) STANAR PROXIMITY & TRAVEL AJUSTMENT (-GG OR -GH) HushStop PROXIMITY & TRAVEL AJUSTMENT (-G OR -G) SHOK ASORER STOP (-GM OR -GN) STOP & TRAVEL AJUSTMENT KITS SHAFT STANAR OVERSIZE STANAR OVERSIZE STANAR OVERSIZE STANAR OVERSIZE STANAR OVERSIZE (,,, ) A TO ASI SLIE IMENSIONS Kit contains all components for standard non-z1 units for one direction only. GG TRAVEL AJUSTMENT AN SHOK PAS ON EXTENSION WITH PROVISIONS FOR PROXIMITY SWITH MOUNTING IN OTH IRETIONS.700 (,,, ).830 () This option provides both travel adjustment and polyurethane shock pads on extension; and provisions for mounting of proximity switch targets and brackets on both ends. Switches and bracket kits must be ordered separately. See page for bracket/ target kits and for switch ordering information. Not available with tool plate extension. With tool plate extension use GH option..6 GG AER.750 (,,, ) A TO ASI SLIE IMENSIONS G TRAVEL AJUSTMENT AN HushStop SHOK PAS ON EXTENSION WITH PROVISIONS FOR PROXIMITY SWITH MOUNTING IN OTH IRETIONS.700 (,,, ).830 () This option, quieter than the GG option, provides both travel adjustment and composite shock pads on extension; and provisions for mounting of proximity switch targets and brackets on both ends. Switches and bracket kits must be ordered separately. See page for bracket/target kits and for switch ordering information. ue to the composite shock pads, stop locations may vary. For close tolerance stop locations, use the GG option..6 G AER.750 (,,, ) A TO ASI SLIE IMENSIONS

14 GH TRAVEL AJUSTMENT AN SHOK PAS ON RETRATION WITH PROVISIONS FOR PROXIMITY SWITH MOUNTING ON RETRATION A.6 This option provides both travel adjustment and polyurethane shock pads on retraction and provisions for mounting of proximity switch targets and brackets in the retraction direction only. Switches and bracket kits must be ordered separately. See page for bracket/target kits and for switch ordering information. G TRAVEL AJUSTMENT AN HushStop SHOK PAS ON RETRATION WITH PROVISIONS FOR PROXIMITY SWITH MOUNTING ON RETRATION A.6 GH AER.750 (,,, ) This option, quieter than the GH option, provides both travel adjustment and composite shock pads on retraction and provisions for mounting of proximity switch targets and brackets in the retraction direction only. Switches and bracket kits must be ordered separately. See page for bracket/target kits and for switch ordering information. ue to the composite shock pads, stop locations may vary. For close tolerance stop locations, use the GH option. G AER.750 (,,, ) GI TRAVEL AJUSTMENTS, SHOK PAS, AN PROVISIONS FOR PROXIMITY SWITHES IN OTH IRETIONS A 1/2 GI AER.750 (,,, ) This option provides both travel adjustment and polyurethane shock pads in both directions and provisions for mounting of proximity switch targets and brackets on both ends. Switches and bracket kits must be ordered separately. See page for bracket/target kits and for switch ordering information..6 1/2 GI AER.750 (,,, ) G TRAVEL AJUSTMENTS, HushStop SHOK PAS, AN PROVISIONS FOR PROXIMITY SWITHES IN OTH IRETIONS This option,quieter than the GI option, provides both travel adjustment and composite shock pads in both directions and provisions for mounting of proximity switch targets and brackets on both ends. Switches and bracket kits must be ordered separately. See page for bracket/target kits and for switch ordering information. ue to the composite shock pads, stop.6 locations may vary. For close tolerance stop SLIE A locations, use the GI option. SIZE 8 mm PROX 12 mm PROX A TO ASI SLIE IMENSIONS A 1/2 G AER.750 (,,, ) 1/2 G AER.750 (,,, )

15 Q1 ORROSION RESISTANT GUIE SHAFTS Extremely hard corrosion-resistant coating on the guide shafts for use in applications where moisture may corrode hardened ground shafts. End faces of the shafts remain uncoated. onsult PH for fully coated shafts. V1 FLUORO-ELASTOMER SEALS Z1 ELETROLESS NIKEL PLATING Fluoro-Elastomer seals are available for seal compatibility with certain fluids. Seal compatibility should be checked with the fluid manufacturer for proper application. onsult PH for high temperature applications. This option provides electroless nickel plating on all externally exposed ferrous parts except the guide shafts and cylinder rod end. This optional plating can be used for protecting the slide from severe or corrosive environments. The guide shafts can be made corrosionresistant by specifying the -Q1 shaft option. NOTE: Shock absorbers are not plated with -Z1 option. GM PROVISIONS FOR SHOK ASORER MOUNTING ON EXTENSION This option provides for mounting a bracket for a shock absorber in the extend direction. This includes mounting holes in the slide body, a shock stop on one shaft, and a stop collar on the other shaft. The shock absorber and shock mounting kit must be ordered separately. This arrangement allows the shock absorber to double as a travel adjustment in the extension direction. See page for shock mounting kit and shock absorber ordering information. Shock stop and mounting bracket are supplied ready for proximity switch bracket and target mounting. O REF J E THREA A REF REF FULLY RETRATE PH SUPPLIE SHOK STOP OLLAR T GM AER SHOK STOP G F L REF A TO ASI SLIE IMENSIONS A REF. GM E L O SIZE S SE AER THREA F G J REF. REF. T /4-16 UNF /4-16 UNF UNF UNF UNF

16 GN PROVISIONS FOR SHOK ASORER MOUNTING ON RETRATION T J GN AER REF FULLY RETRATE PH SUPPLIE SHOK This option provides for mounting a bracket for a shock absorber in the retract direction. This includes mounting holes in the slide body, a shock stop on one shaft, and a stop collar on the other shaft. The shock absorber and shock mounting kit must be ordered separately. This arrangement allows the shock absorber to double as a travel adjustment in the retraction direction. See page for shock mounting kit and shock absorber ordering information. Shock stop and mounting bracket are supplied ready for proximity switch bracket and target mounting. SHOK STOP STOP OLLAR F A REF E TH G L REF A TO ASI SLIE IMENSIONS A REF. GN E L SIZE S SE AER THREA F G J REF. T /4-16 UNF /4-16 UNF UNF UNF UNF GO PROVISIONS FOR SHOK ASORER MOUNTING ON EXTENSION AN RETRATION This option provides for mounting brackets for shock absorbers in both the extend and retract direction. This includes two sets of mounting holes in the slide body, shock stops mounted on the shafts in each direction, and stop collars mounted on the opposite shafts. The shock absorbers and shock mounting kits must be ordered separately. This arrangement allows the shock absorbers to double as travel adjustments in both directions. See page for shock mounting kit and shock absorber ordering information. Shock stops and brackets are supplied ready for proximity switch bracket and target mounting. T 1/2 x (GO AER) O REF TYP J A REF REF FULLY RETRATE PH SHOK STOP OLLAR SHOK STOP 1/2 x (GO AER) G F TYP TYP L REF A TO ASI SLIE IMENSIONS A REF. GO E L O SIZE S SE AER THREA F G J REF. REF. T /4-16 UNF /4-16 UNF UNF UNF UNF

17 G2 G12 SHOK ASORER AN PROXIMITY SWITH REAY ON EXTENSION AN RETRATION T 1/2 x (G2 AER) TYP J A REF STOP OLLAR This option provides mounting brackets for shock absorbers and proximity switches in both directions. This includes mounting brackets for both shock absorbers and proximity switches, proximity targets, and mounting hardware with stop collars and stops mounted on the shafts. The shock absorbers and proximity switches must be ordered separately. This arrangement allows the shock absorbers to double as travel adjustments in both directions. See page for shock absorbers and proximity switches. G2 = 8 mm proximity switch G12 = 12 mm proximity switch O REF P TYP REF FULLY RETRATE PH SHOK A TO ASI SLIE IMENSIONS SHOK STOP 1/2 x (G2 AER) R TYP G F TYP TYP L REF A REF. G2/G12 E L O P R SIZE S SE AER THREA F G J REF. REF. 8 mm 12 mm 8 mm 12 mm T /4-16 UNF /4-16 UNF UNF UNF UNF G3 G13 O REF A REF STOP OLLAR SHOK ASORER & PROXIMITY SWITH REAY ON EXTENSION This option provides mounting brackets for a shock absorber and proximity switch on the extension only. This includes mounting brackets for both shock absorber and proximity switch, a proximity target and mounting hardware, with a stop collar and stop on the shafts. The shock absorber and proximity switch must be ordered separately. This arrangement allows the shock absorber to double as a travel adjustment in the extension direction. See page for shock absorbers and proximity switches. G3 = 8 mm Proximity Switch G13 = 12 mm Proximity Switch E THREA G J L REF REF FULLY RETRATE PH SUPPLIE SHOK T G13 AER SHOK STOP R P F A TO ASI SLIE IMENSIONS A REF. G3/G13 E L O P R SIZE S SE AER THREA F G J REF. REF. 8 mm 12 mm 8 mm 12 mm T /4-16 UNF /4-16 UNF UNF UNF UNF

18 G4 G14 G4 AER REF FULLY RETRATE PH SUPPLIE SHOK SHOK ASORER & PROXIMITY SWITH REAY ON RETRATION This option provides mounting brackets for a shock absorber and proximity switch on the retraction only. This includes mounting brackets for both shock absorber and proximity switch, shaft, a proximity target and mounting hardware, with a stop collar and stop on the other shafts. The shock absorber and proximity switch must be ordered separately. This arrangement allows the shock absorber to double as a travel adjustment in the retract direction. See page for shock absorbers and proximity switches. T SHOK STOP STOP OLLAR P F A REF E TH J G R G4 = 8 mm Proximity Switch G14 = 12 mm Proximity Switch A TO ASI SLIE IMENSIONS L REF A REF. G4/G14 E P R SIZE S SE AER THREA F G J REF. 8 mm 12 mm 8 mm 12 mm T /4-16 UNF /4-16 UNF UNF UNF UNF SHOK KITS Each shock mounting kit contains one shock bracket with all necessary hardware for mounting one shock absorber in either direction. Slide unit must be ordered as provisions for shock absorber. Shock absorbers must be ordered separately. See PH Product Sizing atalog for kit numbers. SHOK ASORERS Shock absorbers are ordered separately and should be properly matched to the slide application. See PH Product Sizing atalog for proper shock absorber selection and shock numbers. S SHOK PAS ON EXTENSION T SHOK PAS ON RETRATION The -S option adds shock pads on extension to the -GM, -GO, -G2, -G3, -G12, or -G13 shock absorber option. The shock pads are assembled between the shock stop (stop collar) and the slide body. The purpose of this option is to complement the shock absorber by eliminating metal to metal contact at the end of slide extension. Shock pads do not affect length adders for shock absorber options. The -T option adds shock pads on retraction to the -GN, -GO, -G2, -G4, -G12, or -G14 shock absorber option. The shock pads are assembled between the shock stop (stop collar) and the slide body. The purpose of this option is to complement the shock absorber by eliminating metal to metal contact at the end of slide retraction. Shock pads do not affect length adders for shock absorber options. K HushStop SHOK PAS ON EXTENSION L HushStop SHOK PAS ON RETRATION The -K option adds composite shock pads on extension to the -GM, -GO, -G2, -G3, -G12, or -G13 shock absorber option. The shock pads are assembled between the shock stop (stop collar) and the slide body. The purpose of this option, quieter than the -S option, is to complement the shock absorber by eliminating metal to metal contact at the end of slide extension. Shock pads do not affect length adders for shock absorber options. ue to the composite shock pads, stop locations may vary. For close tolerance stop locations, use the -S option. The -L option adds composite shock pads on retraction to the -GN, -GO, -G2, -G4, -G12, or -G14 shock absorber option. The shock pads are assembled between the shock stop (stop collar) and the slide body. The purpose of this option, quieter than the -T option, is to complement the shock absorber by eliminating metal to metal contact at the end of slide retraction. Shock pads do not affect length adders for shock absorber options. ue to the composite shock pads, stop locations may vary. For close tolerance stop locations, use the -T option

19 GV SIE MOUNTING HOLES IN POSITION 2 This option provides an additional mounting pattern on one side of the slide body. This pattern is ideal if the slide is to be mounted on edge for applications where a narrow profile is required. A REF REF E NOTE: MTG HOLES ENTERE ON ENTERLINE OF UNIT OPTION AERS MOEL A E F THREA Sx x.375 P SEx x.375 P Sx /4-20 x.375 P SEx /4-20 x.375 P Sx /4-20 x.430 P SEx /4-20 x.430 P Sx /8-16 x.650 P SEx /8-16 x.650 P Sx /8-16 x.750 P SEx /8-16 x.750 P 4X F THREA H47 ROLOK SLIE & ROLOK PH s Rodlok is ideal for locking the tool plate while in a static/ stationary position. When the pressure is removed from the port of the Rodlok, the mechanism will grip the piston rod of the cylinder and prevent it from moving. The loads are held indefinitely without power. Rodlok performance is application and environment sensitive (cleanliness of rod or Rodlok will also affect performance). THE ROLOK IS NOT ESIGNE TO E USE AS A PERSONNEL SAFETY EVIE. SIZE STATI LOKING FORE* lb N NOTE: *Locking force given in table is the actual locking force with a dry clean rod and does not include any safety factor. OPERATING PRESSURE The operating pressure for the locking device is different than the operating pressure for the slide to which it is attached. The locking device of the Rodlok is designed with an operating pressure range of 60 psi [4 bar] minimum to 150 psi [10 bar] maximum. The Series S/SE Slide with a Rodlok attached has an operating pressure range of 45 psi [3 bar] minimum to 150 psi [10 bar] maximum. NOTE: When ordering a replacement cylinder (-H4), Rodlok must be ordered separately. ORE in Sx SEx S/SEx S/SEx S/SEx S/SEx EVIE WEIGHT lb AAPTOR WEIGHT lb NOTE: Total weight includes rod adder for -H46/-H47 cylinder. TOTAL WEIGHT lb

20 REPLAEMENT ROLOK KITS NN JJ A + TRAVEL SQ LL KK MM PORT GG MOEL NO. Sx SEx S/SEx S/SEx S/SEx S/SEx LOKING EVIE KIT AAPTOR KIT* OMPLETE ROLOK* NOTES: 1) *Kits ship with cylinder mounting hardware. 2) Part numbers listed above are intended for replacement purposes only and are to be used specifically on slides with the -H47 option. The Rodlok locking device and adaptor can be purchased separately as kits. See chart above. The locking device and adaptor are not available with a corrosion resistant (-Z1 option) finish. LETTER IM. GG KK LL MM NN JJ A MOEL NUMER Sxx SExx Sxx SExx Sxx SExx Sxx.5 SExx.5 Sxx.3 SExx /8 NPT /8 NPT

21 AESSORIES: SERIES S & SE SLIES switches & brackets (For use with -E or -m options) See Switches and Sensors section for complete switch specifications. rackets SLIE OMPAT SWITH SIZE racket No Each bracket contains components for one direction. OPTION -E -M TYPE HALL REE PART NO PROXIMITY SWITHES ESRIPTION Sink Type V Source Type V Sink Type V, Quick onnect Source Type V, Quick onnect Sink or Source Type V A Type VA with urrent Limit Sink or Source Type V, Quick onnect A Type VA, Quick onnect with urrent Limit STrain relief kits ompact switch bracket for sizes,,, and have built in strain reliefs. ompact Switch Strain Relief Kit for size is onsult PH for availability of other PH Switches and rackets. proximity switch bracket & TARGET kits (For use with proper -Gxxx option) See Switches and Sensors section for complete switch specifications. Each kit contains a bracket, target, and hardware for mounting one threaded proximity switch on an S or SE Slide. Switches must be ordered separately. Slides must be ordered with provisions for proximity switches in order for these bracket and target kits to function. See individual proximity & switch ready options for switch dimensions. PROXIMITY SWITH RAKET AN TARGET KITS SLIE SIZE 8 mm SWITH SIZE 12 mm Kit contains all components for standard non-z1 unit for one direction only. PART NO PROXIMITY SWITHES ESRIPTION 8 mm Inductive Proximity Switch NPN (Sink) with 2 meter able 8 mm Inductive Proximity Switch PNP (Source) with 2 meter able SHOK ASORERS See individual shock ready options for shock absorber dimensions. SLIE SIZE PH SHOK ASORER NUMER* x x x x x * See PH product sizing software or Sizing atalog for proper shock selection. SLIE SIZE PH SHOK MOUNTING KIT Kit contains components for standard non -Z1 units for one direction only