SINGLE ROD Pneumatic. Major Benefits

Transcription

1 SINGL ROD Pneumatic SPMNT Major enefits Ideal for shot pin applications Shock pad options reduce noise and minimize end of stroke shock Imperial or metric versions available Simple construction for easy field maintenance Large rod bearing area ensures high side load capacity Next day delivery shoulders prevent tooling movement all units are inductive proximity switch ready cover acetyl rod bushing provides excellent wear characteristics and accurately locates rod seal body piston threaded mounting holes on both sides for simple tooling attachment cap hardened, ground and plated alloy steel rod and large bearing surfaces provide maximum wear resistance plus high side load capacity both thru and dowel holes in body are provided for quick setup and convenient, repeatable mounting piston bore and bearing surfaces are hardcoated with PTF for long life and wear resistance long life nitrile piston and rod seals for low maintenance all units with or M5 ports come standard with barbed fittings

2 ORDRING DT: Series SINGL ROD escapements TO ORDR SPIFY: Product, Series, Type, Design No., ore Size, Stroke, and Options. PRODUT L - scapement TYP S - Single Rod OR SIZ 10 mm 12 mm 20 mm 32 mm SHOK PDS - Shock Pads on both directions See stroke table for option effect on stroke. SWITH RDY OPTIONS - Hall ffect Switch Ready Series 5580 Switch on Sx10 units Series 5360 Switch on all other units Switch sensing is limited to one direction on Sx10 and Sx12 units. Switches and brackets must be ordered separately. L S 1 10 x R - - V1 SRIS - Standard Duty DSIGN NO. 1 - Imperial 5 - Metric STROK Stroke [mm] ore [mm] Option may affect stroke. See table. STROK DJUSTMNT R - Stroke djustment on retract (Stroke adjustment not available on Sx10 units.) See stroke table for option effect on stroke. MISLLNOUS OPTIONS R9 - Flats and threaded holes on sides 1 and 3 (2 and 4 standard) V1 - Fluoro-lastomer Seals NOT: V1 option not available with R or options Options may affect unit length. See dimensional pages and option information details. 4 mm SQUR INDUTIV PROXIMITY SWITHS mm SQUR INDUTIV PROXIMITY SWITHS INDUTIV SWITH MOUNTING KITS PROXIMITY SWITH KIT NUMR 4 mm Round Inductive mm Square Inductive H PROXIMITY SWITH MOUNTING KIT ONTINS: 1 SWITH RKT 1 RKT MOUNTING SRW Refer to this product s online catalog in the product section for complete information including related dimensions and additional specifications. See link at bottom of this page. SRIS 5360 HLL FFT SWITHS NPN (Sink) VD, 2 meter cable PNP (Source) VD, 2 meter cable NPN (Sink) VD, Quick onnect PNP (Source) VD, Quick onnect SRIS 5580 HLL FFT SWITHS NPN (Sink) VD, 2 meter cable PNP (Source) VD, 2 meter cable NPN (Sink) VD, Quick onnect PNP (Source) VD, Quick onnect 3-10 D & Sizing ssistance Use PHD's free online Product Sizing and D onfigurator at

3 NGINRING DT: Series SINGL ROD escapements SPIFITIONS OPRTING PRSSUR OPRTING TMPRTUR STNDRD TOLRN RTD LIF VLOITY LURITION MINTNN *-V1 option may reduce life. SRIS 20 to 150 psi [1.4 to 10 bar] air -20 to 180 F [-28 to 82 ] +.031/-.000 [+.08/-.00] 5 million cycles* 20 in/sec [0.5 m/sec] typical min, zero load at 100 psi [7 bar] Factory lubricated for rated life Field repairable FFTIV WIGHT TL OR ROD R STNDRD STROK DJUSTMNT UNIT in mm DIRTION in 2 mm 2 lb kg lb kg Sx XTND RTRT Sx XTND RTRT Sx XTND RTRT Sx XTND RTRT YLINDR THRUST ULTION Imperial Metric F = P x F = 0.1 x P x F = ylinder Force lb N P = Operating Pressure psi bar = ffective rea in 2 mm 2 STROK TL OPTION Sx10 Sx12 Sx20 Sx32 STNDRD UNIT.394 [10].472 [12].787 [20] 1.26 [32] SHOK PD (-).354 [9].433 [11].787 [20] 1.26 [32] STROK DJ (-R).413[10.5].728 [18.5] 1.20 [30.5] -R [9.5].728 [18.5] 1.20 [30.5] RSPONS TIM Following is a reference guide to response times of the piston rod for extend and retract based on a typical load at 87 psi [6 bar]. The response time for rod extension will be less than the response time for retraction. Varying the operating pressure, air line diameter, and the applied load will affect the response time. Response times shown do not include valve response time. UNIT Sx10 Sx12 Sx20 Sx32 TYPIL LOD lb kg RTRT TIM sec XTND TIM sec MXIMUM ROD TORQU MODL NO. Sx10 Sx12 Sx20 Sx32 STNDRD DUTY in-lb Nm MX. ROD LOD TORQU = (LOD) x R R SUPPORT L For applications which exceed the maximum allowable rod torque, the tooling should be supported as shown. alculation without the support: Max. Rod Load Torque = (Load) x R Sizing & pplication ssistance Use PHD's free online Product Sizing pplication or view the Product Sizing atalog at:

4 DIMNSIONS: Series SINGL ROD escapements MOUNTING SURF F 4 D XTND S U J W T PORT G SQ TOP VIW T PORT K L 2X H THRD THRU H ROD M Q N 2X Ø THRU FOR P SRW R ROD MOUNTING DTIL P OTTOM VIW 2X LRN HOL FOR Q DOWL PIN 1/2 X X Y MX Z HX 2X T PORT TOP VIW WITH OPTIONL STROK DJUSTMNT (Not available on Sx10 units) LTTR DIM. PHD OR D F G H J K L M N P Q R S T U W X Y Z S110x UN #6 3 mm THD IMPRIL MODL NO. S112x12 S120x UN UN #6 #10 3 mm 4 mm THD THD mm 6 mm S132x /16-18 UN /16 5 mm /8 NPT mm S510x10 10 mm M3 x M3 3 mm M5 x NOTS: 1) MTRI DIMNSIONS R IN MILLIMTRS. 2) LL DIMNSIONS R OUT TH NTRLIN UNLSS OTHRWIS SPIFID. MTRI MODL NO. S512x12 S520x20 S532x32 12 mm 20 mm 32 mm M3 x 0.5 M5 x 0.8 M8 x M3 M5 M8 3 mm 4 mm 5 mm M5 x 0.8 M5 x 0.8 1/8 SP mm 6 mm 8 mm D & Sizing ssistance Use PHD's free online Product Sizing and D onfigurator at ll dimensions are reference only unless specifically toleranced.

5 OPTIONS: Series SINGL ROD escapements SHOK PDS INSTLLD OTH DIRTIONS R STROK DJUSTMNT ON RTRT Polyurethane shock pads for noise reduction and absorption of shock at ends of stroke are available on each end of Series scapements. Shock pads permit higher piston velocities for shorter cycle times. Noise reduction is beneficial for the working environment. Stroke adjustment screws can be set for precise adjustment of the retracted position from 0" to full stroke. Stroke adjustment option reduces the standard stroke by.059 [1.5 mm]. NOT: Not available on Sx10 unit. NOT: Shock pads reduce standard stroke by.039 [1 mm] on Sx10 and Sx12 units. SWITH RDY Series 5580 on Sx10 units Series 5360 on all other units Switch Ready option includes magnets on the rod for PHD solid state switches. Units are equipped to sense in two directions, both extend and retract. Switches must be ordered separately. See chart below. NOT: Sx10 and Sx12 units will sense in one direction only. R9 ROD ND OPTION This option specifies flats and threaded holes on sides 1 and 3. Mounting holes and flats on sides 2 and 4 are standard. Options may affect unit length. See dimensional pages and option information details. Refer to this product s online catalog in the product section for complete information including related dimensions and additional specifications. See link at bottom of this page. INDUTIV PROXIMITY SWITH RDY ll units are inductive proximity switch ready as standard. threaded hole is provided in the body cover to allow attachment of PHD bracket kits for 4 mm round or 6 mm square inductive proximity switches. NOT: Switch targets mounted on the rod end or on the rod tooling are to be provided by the end user. See Switches and Sensors section for complete switch specifications

6 OPTIONS: Series SINGL ROD escapements SHOK PDS INSTLLD OTH DIRTIONS R STROK DJUSTMNT ON RTRT Polyurethane shock pads for noise reduction and absorption of shock at ends of stroke are available on each end of Series scapements. Shock pads permit higher piston velocities for shorter cycle times. Noise reduction is beneficial for the working environment. NOT: Shock pads reduce standard stroke by.039 [1 mm] on Sx10 and Sx12 units. ROD PISTON SHOK PDS Stroke adjustment screws can be set for precise adjustment of the retracted position from 0" to full stroke. Stroke adjustment option reduces the standard stroke by.059 [1.5 mm]. NOT: Not available on Sx10 unit. STROK DJUSTMNT SRW.059 [1.5] R9 ROD ND OPTION This option specifies flats and threaded holes on sides 1 and 3. Mounting holes and flats on sides 2 and 4 are standard SWITH RDY Series 5580 on Sx10 units Series 5360 on all other units Switch Ready option includes magnets on the rod for PHD solid state switches. Units are equipped to sense in two directions, both extend and retract. Switches must be ordered separately. See Switches and Sensors section for complete specifications. NOT: Sx10 and Sx12 units will sense in one direction only NPN (Sink) VD, 2 meter cable PNP (Source) VD, 2 meter cable NPN (Sink) VD, Quick onnect PNP (Source) VD, Quick onnect NPN (Sink) VD, 2 meter cable PNP (Source) VD, 2 meter cable NPN (Sink) VD, Quick onnect PNP (Source) VD, Quick onnect SRIS 5360 HLL FFT DIMNSIONS SRIS 5580 HLL FFT DIMNSIONS [2.0] [7.5] MODL NO. Sx12 Sx20 Sx32 DIM [8.2] [4.5] [5.5] DIM [4.8] [9.0] [14.5] DIM [12.3] [17.6] Switch information is continued on page Numbers in [ ] are for metric units and are in millimeters. SWITH RKT KIT (NUMR 57880) MUST ORDRD SPRTLY. SRIS 5580 IS VILL ON Sx10 UNITS ONLY. ll dimensions are reference only unless specifically toleranced

7 PROXIMITY SWITHS: Series SINGL ROD escapements INDUTIV PROXIMITY SWITH RDY ll units are inductive proximity switch ready as standard. threaded hole is provided in the body cover to allow attachment of PHD bracket kits for 4 mm round or 6 mm square inductive proximity switches. See Switches and Sensors section for complete specifications. NOT: Switch targets mounted on the rod end or on the rod tooling are to be provided by the end user. Illustrated below are examples (showing the extended rod position) of how 4 mm round and 6 mm square inductive proximity switches are installed. The suggested maximum gap between target and switch is.032 [0.8]. PROXIMITY SWITH 4 mm Round Inductive 6 mm Square Inductive KIT NUMR H PROXIMITY SWITH MOUNTING KIT ONTINS: 1 SWITH RKT 1 RKT MOUNTING SRW 4 mm SQUR INDUTIV PROXIMITY SWITHS mm SQUR INDUTIV PROXIMITY SWITHS MODL NO. Sx10 Sx12 Sx20 Sx32 DIM [8.5] [5.3] DIM [1.5] [3.0] [7.2] [12.7] DIM [13.3] [14.8] [19.0] [24.5] MODL NO. Sx10 Sx12 Sx20 Sx32 DIM [7.5] [4.5] [6.8] [6.8] DIM [2.0] [3.5] [7.7] [13.3] DIM [9.5] [13.7] [19.2] ll dimensions are reference only unless specifically toleranced