TFM 1600 Seat Body Material: Stainless. PTFE Seat Body Material: Stainless and Brass. Catalog No. V81-5 Sept. 2008

Transcription

1 Ctlog No. V81-5 Sept Vlve with lever hndle Working pressure sets: 68.9 br (1000 psig) TFM sets: 137 br (2000 psig) Vlve with butterfly hndle Working pressure sets: 68.9 br (1000 psig) TFM sets not pplicble Compct brstock construction for high integrity Blow-out proof design with internlly loded stem Floting Bll design providing set wer compenstion Micro-finished bll ensures lek-tight shut-off on pressure Stndrd lever hndle, optionl butterfly hndle. V81 series bll vlve offers sfe nd relible performnce for wide rnge of onshore nd offshore pplictions: wter, oil, gs, petrochemicl nd generl duty pplictions Component 1. Body 2. Bll 3. Set (2) 4. O-Ring (2) 5. End Connector (2) 5-1. Insert 6. Bll Vlve Stem 7. Lower Pcking 8. Upper Pcking 9. Grnd Wsher 10. Spring Wsher 11. Hndle 12. Lock Nut 4. O-Ring is pplicble to DK-LOK end connection 5. End Connector is for DK-LOK end connection 5-1. Insert is for Pipe Thred end connection * TFM 1600 set is pplicble only to body in stinless. Vlve Body Mterils Stinless Steel Brss SS316/STM 276 or 479 STM B16 or JIS H3250 SS316 / STM 276 / D1710 for pressure 68.9 br (1000 psig) TFM 1600 for pressure 137 br (2000 psig)* FKM NBR SS316/ STM 276 or 479 SS316/ STM 276 or 479 / D1710 / D1710 SS304 /STM 276 or 479 STM B16 or JIS H3250 Stinless Steel SS304 Lever hndle with vinyl sleeve ZINC/ STM B240 Butterfly hndle, Nickel-plted SS304 SS304 TFM 1600 Set Body Mteril: Stinless Set Body Mteril: Stinless nd Brss

2 Bll Vlves V81 Series Bsic Ordering Number V81- V81B- V81C- V81D- V81E- D-6M D-4T F-4N D-10M D-6T F-6N D-12M D-8T F-8N D-16M D-10T F-12N D-12T D-16T F-16N End Connection Inlet / Outlet 6mm DK-LOK 1/4 in. DK-LOK 1/4 in. Femle NPT 10mm DK-LOK 3/8 in. DK-LOK 3/8 in. Femle NPT 12mm DK-LOK 1/2 in. DK-LOK 1/2 in. Femle NPT 16mm DK-LOK 5/8 in. DK-LOK 3/4 in. Femle NPT 3/4 in. DK-LOK 1 in. DK-LOK 1 in. Femle NPT mm (in.) 5 (0.20) 7.50 (0.30) 9.00 (0.35) (0.49) (0.63) Dimensions shown re for reference only, subject to chnge. Dimensions with DK-LOK nuts re in finger-tight position L 79 (3.11) 79 (3.11) 41.9 (1.65) 90 (3.54) 90 (3.54) 45 (1.77) 98 (3.86) 98 (3.86) (2.21) 108 (4.25) 108 (4.25) 60 (2.36) 109 (4.29) 133 (5.23) 78.1 (3.07) H 31 (1.22) 40 (1.57) 42 (1.65) 51 (2.00) 55 (2.16) Dimensions, hex 17 (11/16) (13/16) 27 (1-1/16) 32 (1-1/4) 38 (1-1/2) mm (in.) 59.5 (2.34) 81 (3.19) 81 (3.19) (4.04) (4.04) (1.20) (1.65) (1.81) (1.95) (2.68) H (0.93) (1.18) (1.41) (1.50) (1.77) Every vlve is fctory tested with nitrogen br (600 psig) for lekge t the set to mximum llowble lek rte of 0.1 SCCM. The pcking is tested with nitrogen for no detectble lekge. Select vlve ordering number, pplicble option(s) from designtor tbles listed below. Exmples V81-D-6M- TF- S V81-D-6M- VT- BF- B O-ring Set Mteril Hndle Body mteril Nil: FKM O-ring is stndrd for SS316 body. Nil: NBR O-ring is stndrd for Brss body. VT: FKM O-ring for Brss body BN: NBR O-ring for SS316 Nil: Stndrd sets for 68.9 br (1000 psig) working pressure. TF: Optionl TFM1600 for 137 br (2000 psig) working pressure. Nil: Stndrd lever hndle BF: Optionl butterfly hndle S: S316 B: Brss NOTE: O-ring is required for DK-LOK end connection. NOTE: TFM1600 set is not pplicble to Brss vlve. NOTE: BF option is not pplicble to the vlve with TF sets. Sfe Vlve Selection The selection of vlve for ny ppliction or system design must be considered to ensure sfe performnce. Vlve function, vlve rting, mteril comptibility, proper instlltion, opertion nd mintennce remin the sole responsibillty of the system designer nd the user. Dk Tech ccepts no libility for ny improper selection, instlltion, opertion or mintennce. e e

3 V82 Series Bll Vlves Pressure Rting up to 3000psig Ctlog No. V82-3 pril 2008 Fetures of V82 Series Seling is chieved without system pressure Pressure up to 3000 psig (206 br) Bi-directionl flow Lowest ded spce design Opertion & Pcking djustment Nylon Directionl hndle - indictes the flow through the vlve. Pnel mounting nut - is stndrd nd permits vlve to pnel or ctutor. Top-loded pcking - llows pcking djustment with the vlve in-line. Cpsule pcking - fills voids in the vlve body nd prevents fluid entrpment. - llows lowest ded spce. Support rings nd discs - retins the cpsule pcking nd prevent cold flow. Integrl bll stem - mchined from single piece br stock. - elimintes the bcklsh during hndle ctution. One-piece body - reduces the number of potentil lek points. Mterils of Construction V82 vlves re designed to control fluid in full open nd closed position; using V82 vlves to throttle the flow my reduce the vlve life. Vlves tht hve not been ctuted for period of time my hve higher initil ctution torque. Every vlve working pressure is djusted for fctory test t 1000 psig ( C (70 F). For use in higher pressure, the vlve pcking my be required for re-djustment. Pcking djustment my be required during the vlve in service. ppliction nlyticl mrket requiring vlve with lowest ded volume to prevent fluid entrpment which cn cuse contmintion. Control Smpling Systems, nd Process Instrumenttion mrket requiring vlve with compct size, high flow cpcity nd directionl indiction of flow. Fctory Test nd Pckging Component 1. Hndle 2. Set Screw 3. Pcking bolt 4. Upper Glnd 4. Pcking Spring (VL82 series) 5. Bushing 6. Lower glnd 6. Pcking Glnd (VL82 series) 7 & 11. Upper & Lower Pcking 8. Bll stem 9. Support rings 10. Side discs 12. Pnel nut 13. Body Vlve Body Mterils Stinless Steel Grde/STM Specifiction Nylon with brss insert 17-4PH/564 SS316/276 or 479 SS316/276 or PH/693 /D1710 type 1, Grde 1, Clss B SS316/276 SS316/276 SS316/276 or 479 SS316/276 /D1710 type 1 SS316/276 SS316 powered metl/b783 (fluorocrbon coting) Molybdenum disulfide with hydrocrbon coting. Note: 1. Wetted prts nd lubricnts re listed in blue. 2. Lubricnt is Fluorinted-bsed. Lubricnts re vilble for specific ppliction. Every vlve is fctory tested with nitrogen gs t 1000 psig (68.9 br) for lekge t set to mximum llowble lek rte of 0.1 SCCM. The pcking is tested with nitrogen gs for no detectble lekge. Every vlve is clened nd pckged in ccordnce with DK clening stndrd DC-01 Brss Brss B16 Brss B16 Brss B16

4 Bll Vlves V82 Series 2-wy On-off Vlves Technicl Dt for V82 series with stndrd set Vlve Series In-Line pttern V82 V82B V82C, V82D - ngle pttern V82-, V82B- - - V82C-, V82D- Pressure Rting psig br Temp. Rnge set 10 C to 65 C (50 F to 150 F) Technicl Dt for VL82 series with set Vlve Series In-line pttern VL82 series VL82B series Pressure Rting psig br Temperture Rting -54 C to 65 C (-65 F to 150 F) To improve therml cycle performnce VL82 series hs pcking springs in the plce of V82 series upper glnd & bushing. Ordering Informtion nd Tble of Dimensions Bsic Ordering Number D1T- D2T- D3M- V82- D4T- D6M- F2N- D4T- D6T- D6M- D8M- V82B- F2N- F4N- M4N- F4R- D6T- D10M V82C- F4N- F6N- F6R- D8T- D12T- V82D- D12M- F8N- F8R- End Connections Inlet Outlet 1/16" Dk-Lok 1/8" Dk-Lok 3mm Dk-Lok 1/4" Dk-Lok 6mm Dk-Lok 1/8" Femle NPT 1/4" DK-Lok 3/8" Dk-Lok 6mm Dk-Lok 8mm Dk-Lok 1/8" Femle NPT 1/4" Femle NPT 1/4" Mle NPT 1/4" ISO Femle Tpered 3/8" Dk-Lok 10mm Dk-Lok 1/4" Femle NPT 3/8" Femle NPT 3/8" ISO Femle Tpered 1/2" Dk-Lok 3/4" DK-Lok 12mm Dk-Lok 1/2" Femle NPT 1/2" ISO Femle Tpered mm inch Dimensions mm (inches) Inline ngle L L1 L2 H3 H2 H1 T D H W (1.68) 21.3(0.84) 21.3(0.84) - 8.6(0.34) 7.1(0.28) 28.4(1.12) 6.4(1/4) 15.1(19/32) 34.5(1.36) 14.7(0.58) (2.01) 25.7(1.01) 25.7(1.01) 24.6(0.97) 51.1(2.01) 25.7(1.01) 25.7(1.01) 24.6(0.97) 56.1(2.21) 27.9(1.10) 27.9(1.10) 27.2(1.07) 56.1(2.21) 27.9(1.10) 27.9(1.10) 27.2(1.07) 41.1(1.62) 20.6(0.81) 20.6(0.81) 20.6(0.81) 8.6(0.34) 8.6(0.34) 8.6(0.34) 8.6(0.34) 8.6(0.34) 7.1(0.28) 7.1(0.28) 7.1(0.28) 7.1(0.28) 7.1(0.28) 28.4(1.12) 28.4(1.12) 28.4(1.12) 28.4(1.12) 28.4(1.12) 6.4(1/4) 6.4(1/4) 6.4(1/4) 6.4(1/4) 6.4(1/4) 15.1(19/32) 34.5(1.36) 14.7(0.58) 15.1(19/32) 34.5(1.36) 14.7(0.58) 15.1(19/32) 34.5(1.36) 14.7(0.58) 15.1(19.32) 34.5(1.36) 14.7(0.58) 15.1(19/32) 34.5(1.36) 14.7(0.58) (2.36) 30.0(1.18) 30.0(1.18) 29.7(1.17) 11.2(0.44) 65.5(2.58) 32.8(1.29) 32.8(1.29) 32.8(1.29) 11.2(0.44) 60.7(2.39) 30.5(1.20) 30.5(1.20) 29.7(1.17) 11.2(0.44) 62.5(2.46) 31.2(1.23) 31.2(1.23) 30.5(1.20) 11.2(0.44) 50.8(2.00) 25.4(1.00) 25.4(1.00) 25.4(1.00) 11.2(0.44) 52.3(2.06) 26.2(1.03) 26.2(1.03) 26.2(1.03) 11.2(0.44) 50.8(2.00) 25.4(1.00) 25.4(1.00) 26.2(1.03) 11.2(0.44) 9.7(0.38) 9.7(0.38) 9.7(0.38) 9.7(0.38) 9.7(0.38) 9.7(0.38) 9.7(0.38) 38.9(1.53) 38.9(1.53) 38.9(1.53) 38.9(1.53) 38.9(1.53) 38.9(1.53) 38.9(1.53) 4.8(3/16) 19.8(25/32) 39.6(1.56) 19.8(0.78) 4.8(3/16) 19.8(25/32) 39.6(1.56) 19.8(0.78) 4.8(3/16) 19.8(25/32) 39.6(1.56) 19.8(0.78) 4.8(3/16) 19.8(25/32) 39.6(1.56) 19.8(0.78) 4.8(3/16) 19.8(25/32) 39.6(1.56) 19.8(0.78) 4.8(3/16) 19.8(25/32) 39.6(1.56) 19.8(0.78) 4.8(3/16) 19.8(25/32) 39.6(1.56) 19.8(0.78) (2.06) 26.2(1.03) 26.2(1.03) (0.44) 9.7(0.38) 38.9(1.53) 4.8(3/16) 19.8(25/32) 39.6(1.56) 19.8(0.78) (3.05) 38.6(1.52) 38.6(1.52) 36.3(1.43) 14.2(0.56) 14.2(0.56) 50.8(2.00) 78.0(3.07) 38.9(1.53) 38.9(1.53) 36.9(1.43) 14.2(0.56) 14.2(0.56) 50.8(2.00) 63.5(2.50) 31.8(1.25) 31.8(1.25) 31.8(1.25) 14.2(0.56) 14.2(0.56) 50.8(2.00) 63.5(2.50) 31.8(1.25) 31.8(1.25) 31.8(1.25) 14.2(0.56) 14.2(0.56) 50.8(2.00) 9.5(3/8) 9.5(3/8) 9.5(3/8) 9.5(3/8) 28.6(1-1/8) 52.6(2.07) 28.4(1.12) 28.6(1-1/8) 52.6(2.07) 28.4(1.12) 28.6(1-1/8) 52.6(2.07) 28.4(1.12) 28.6(1-1/8) 52.6(2.07) 28.4(1.12) (2.50) 31.8(1.25) 31.8(1.25) (0.56) 14.2(0.56) 50.8(2.00) 9.5(3/8) 28.6(1-1/8) 52.6(2.07) 28.4(1.12) (3.92) 49.8(1.96) 49.8(1.96) 17.5(0.69) 17.5(0.69) 76.2(3.00) 99.6(3.92) 49.8(1.96) 49.8(1.96) 17.5(0.69) 17.5(0.69) 76.2(3.00) 99.6(3.92) 49.8(1.96) 49.8(1.96) 17.5(0.69) 17.5(0.69) 76.2(3.00) 79.2(3.12) 39.6(1.56) 39.6(1.56) 39.6(1.56) 17.5(0.69) 17.5(0.69) 76.2(3.00) 9.5(3/8) 9.5(3/8) 9.5(3/8) 9.5(3/8) 38.1(1-1/2) 61.7(2.43) 38.1(1.50) 38.1(1-1/2) 61.7(2.43) 38.1(1.50) 38.1(1-1/2) 61.7(2.43) 38.1(1.50) 38.1(1-1/2) 61.7(2.43) 38.1(1.50) (3.12) 39.6(1.56) 39.6(1.56) (0.69) 17.5(0.69) 76.2(3.00) 9.5(3/8) 38.1(1-1/2) 61.7(2.43) 38.1(1.50) ll dimensions shown re for reference only nd re subject to chnge. Dimensions with Dk-Lok nuts re in finger-tight position. Ptterns: To order ngle pttern, use - s suffix to the bsic ordering number. Exmple: V82B-D-4T--S Top mounting: To order Top mounting option, use -TM s suffix to the bsic ordering number. Exmple: V82C-D-6T-TM-S 2 Copyright 2001, 2008 Dk Tech Corportion, ll Rights Reserved.

5 Bll Vlves V82 Series 3-wy Switching Vlves Technicl Dt for vlves with stndrd set Vlve Series V82-3B, V82B-3B V82C-3B, V82D-3B Pressure Rting psig br Temperture Rnge set 10 C to 65 C (50 F to 150 F) Ordering Informtion nd Tble of Dimensions Bsic Ordering Number D1T- D2T- D4T- D3M- D6M- F2N- D4T- D6M- D8M- F4N- F4R- D6T- D10M- F4N- F6N- F6R- D8T- D12T- D12M- F8N- F8R- V823- V823B- V823C- V823D- End Connections 1/16" Dk-Lok 1/8" Dk-Lok 1/4" Dk-Lok 3mm Dk-Lok 6mm Dk-Lok 1/8" Femle NPT 1/4" Dk-Lok 6mm Dk-Lok 8mm Dk-Lok 1/4" Femle NPT 1/4" ISO Femle Tpered 3/8" Dk-Lok 10mm Dk-Lok 1/4" Femle NPT 3/8" Femle NPT 3/8" ISO Femle Tpered 1/2" Dk-Lok 3/4" Dk-Lok 12mm Dk-Lok 1/2" Femle NPT 1/2" ISO Femle Tpered Dimensions mm (inches) mm inch L L1 H1 H2 T D (1.68) 21.3(0.84) 20.6(0.81) 8.6(0.34) 28.7(1.13) 6.4(1/4) 15.0(19/32) (2.01) 25.7(1.01) 24.6(0.97) 8.6(0.34) 28.7(1.13) 6.4(1/4) 15.0(19/32) (2.21) 27.9(1.10) 27.2(1.07) 8.6(0.34) 28.7(1.13) 6.4(1/4) 15.0(19/32) (2.01) 25.7(1.01) 24.6(0.97) 8.6(0.34) 28.7(1.13) 6.4(1/4) 15.0(19/32) (2.21) 27.9(1.10) 27.2(1.07) 8.6(0.34) 28.7(1.13) 6.4(1/4) 15.0(19/32) (1.63) 20.6(0.81) 20.6(0.81) 8.6(0.34) 28.7(1.13) 6.4(1/4) 15.0(19/32) (2.39) 30.5(1.20) 29.7(1.17) 11.2(0.44) 38.9(1.53) 4.8(3/16) 19.8(25/32) (2.39) 30.5(1.20) 29.7(1.17) 11.2(0.44) 38.9(1.53) 4.8(3/16) 19.8(25/32) (2.46) 31.2(1.23) 30.5(1.20) 11.2(0.44) 38.9(1.53) 4.8(3/16) 19.8(25/32) (2.06) 26.2(1.03) 26.2(1.03) 11.2(0.44) 38.9(1.53) 4.8(3/16) 19.8(25/32) (2.06) 26.2(1.03) 26.2(1.03) 11.2(0.44) 38.9(1.53) 4.8(3/16) 19.8(25/32) (2.89) 36.8(1.45) 36.3(1.43) 14.2(0.56) 50.8(2.00) 9.7(3/8) 28.7(1-1/8) (2.89) 36.8(1.45) 36.3(1.43) 14.2(0.56) 50.8(2.00) 9.7(3/8) 28.7(1-1/8) (2.50) 31.8(1.25) 31.8(1.25) 14.2(0.56) 50.8(2.00) 9.7(3/8) 28.7(1-1/8) (2.50) 31.8(1.25) 31.8(1.25) 14.2(0.56) 50.8(2.00) 9.7(3/8) 28.7(1-1/8) (2.50) 31.8(1.25) 31.8(1.25) 14.2(0.56) 50.8(2.00) 9.7(3/8) 28.7(1-1/8) (3.48) 17.5(0.69) 76.2(3.00) 9.7(3/8) 38.1(1-1/2) (3.48) 17.5(0.69) 76.2(3.00) 9.7(3/8) 38.1(1-1/2) (3.48) 17.5(0.69) 76.2(3.00) 9.7(3/8) 38.1(1-1/2) (3.13) 39.6(1.56) 39.6(1.56) 17.5(0.69) 76.2(3.00) 9.7(3/8) 38.1(1-1/2) (3.13) 39.6(1.56) 39.6(1.56) 17.5(0.69) 76.2(3.00) 9.7(3/8) 38.1(1-1/2) ll dimensions shown re for reference only nd re subject to chnge. Dimensions with Dk-Lok nuts re in finger-tight position. H 34.5(1.36) 34.5(1.36) 34.5(1.36) 34.5(1.36) 34.5(1.36) 34.5(1.36) 39.6(1.56) 39.6(1.56) 39.6(1.56) 39.6(1.56) 39.6(1.56) 52.6(2.07) 52.6(2.07) 52.6(2.07) 52.6(2.07) 52.6(2.07) 61.7(2.43) 61.7(2.43) 61.7(2.43) 61.7(2.43) 61.7(2.43) W 14.7(0.58) 14.7(0.58) 14.7(0.58) 14.7(0.58) 14.7(0.58) 14.7(0.58) 19.8(0.78) 19.8(0.78) 19.8(0.78) 19.8(0.78) 19.8(0.78) 28.4(1.12) 28.4(1.12) 28.4(1.12) 28.4(1.12) 28.4(1.12) 38.1(1.50) 38.1(1.50) 38.1(1.50) 38.1(1.50) 38.1(1.50) Flow Dt (0.7) 0.3(1.1) 0.6(2.3) 1.6 (5.7) 1.9 (7.2) 2.8 (10.6) 3.8 (14.0) 4.7 (17.8) 7.6 (28.4) 8.2 (31.0) 9.5 (35.6) 19.0 (71.9) 19.9 (75.5) 20.2 (75.7) Wter US GPM C (70 F) 2-wy ir SCFM C (70 F) Pressure Drop to tmosphere (Δp) psi (br) 50 (3.5) 0.7 (2.6) 1.4 (5.3) 3.5 (13.2) 4.2 (15.9) 6.4 (23.8) 8.5 (31.8) 11.0 (41.6) 17.0 (64.3) 18.0 (68.1) 100 (7.0) 1.0 (3.8) 2.0 (7.6) 5.0 (18.9) 6.0 (22.7) 9.0 (34.0) 12.0 (45.4) 15.0 (56.8) 24.0 (90.8) 26.0 (98.4) 10 (0.7) 1.1 (31) 2.3 (76) 5.6 (195) 6.8 (235) 10.0 (340) 14.0 (481) 17.0 (595) 27.0 (935) 29.0 (1020) 50 (3.5) 3.0 (85) 6.0 (215) 15.0 (538) 18.0 (651) 27.0 (963) 36.0 (1303) 45.0 (1614) 72.0 (2606) 78.0 (2804) 21.2 (79.5) 30.0 (113.6) 34.0 (1189) 90.0 (3115) 42.0 (159.0) 60.0 (227.1) 68.0 (2351) (6514) 44.5 (170.3) 63.0 (237.0) 45.3 (170.3) 64.0 (242.2) 71.0 (2464) (6797) 72.0 (2520) (6797) 100 (7.0) 5.3 (150) 11.0 (396) 27.0 (963) 32.0 (1161) 48.0 (1720) 64.0 (2294) 80.0 (2832) (4531) (5098) (5664) (11611) (12178) (12178) 37.9 (143.8) 84.9 (321.7) (454.2) (4814) (13027) (22939) (0.7) 0.3 (1.1) 0.4 (1.5) 0.9 (3.4) 1.1 (4.2) 2.3 (8,7) 2.5 (9.5) 2.8 (10.6) 4.7 (17.8) 5.3 (20.1) 6.3 (23.8) 11.0 (41.6) 12.0 (45.4) 15.0 (56.8) 2-wy ngle pttern nd 3-wy Wter US GPM C (70 F) ir SCFM C (70 F) Pressure Drop to tmosphere (Δp) psi (br) 50 (3.5) 0.6 (2.3) 1.0 (3.8) 2.1 (7.9) 2.4 (9.1) 5.3 (20.1) 5.6 (21.2) 6.3 (23.8) 11.0 (41.6) 12.0 (45.4) 14.0 (53.0) 100 (7.0) 0.8 (3.0) 1.5 (5.7) 3.0 (11.4) 3.5 (13.2) 7.5 (28.4) 8.0 (30.3) 9.0 (34.1) 15.0 (56.8) 17.0 (64.3) 20.0 (75.7) 10 (0.7) 0.9 (26) 1.7 (57) 3.4 (116) 4.0 (136) 8.5 (283) 9.0 (312) 10.0 (340) 17.0 (595) 19.0 (680) 22.0 (793) 50 (3.5) 2.4 (68) 4.5 (161) 9.0 (312) 10.0 (368) 22.0 (821) 24.0 (878) 27.0 (963) 45.0 (1614) 51.0 (1841) 60.0 (2181) 25.0 (94.6) 35.0 (132.5) 39.0 (1359) (3682) 27.0 (102.2) 38.0 (143.8) 43.0 (1501) (3965) 33.0 (124.9) 46.0 (174.1) 52.0 (1812) (5098) 100 (7.0) 4.3 (122) 8.0 (286) 16.0 (566) 19.0 (680) 40.0 (1444) 42.0 (1529) 48.0 (1728) 80.0 (2832) 90.0 (3115) (3965) (6797) (7363) (8779) 3

6 Bll Vlves V825 / V824 Series V825 Switching 5-wy Bll Vlves Fetures Flow switches from single port to multiple ports or from multiple ports to single port. Spring-loded detent ensures exct port positioning. Technicl Dt with stndrd set Vlve Series V825 V825B Pressure 37 C (100 F) br psig Temperture Rnge 10 to 65 C 50 to 150 F Ordering Informtion nd Tble of Dimensions Ordering Number End Connection mm inch T* indictes the mximum pnel thickness. 3.2 mm (1/8 in.) minimum pnel thickness. D : Pnel hole L 39.4 (1.94) L (0.78) H Dimensions, mm(in.) H (0.44) 38.9 (1.53) 4.1 (5/32) 79.5 (3.13) 39.6 (1.56) 39.6 (1.56) 17.5 (0.69) 76.2 (3.00) 9.7 (3/8) T* D 23.1 (29/32) H 42.9 (1.69) 38.1 (1 1/2) 61.7 (2.43) V824 Crossover 4-wy Bll Vlves Fetures Crossover of two strems Mechnicl stop ensures positive port positioning Technicl Dt with stndrd set Vlve Series V824 V824B Ordering Informtion nd Tble of Dimensions Ordering Number Hndle Options Pressure 37 C (100 F) br F2N-S 1/8 in. Femle NPT V F2G-S 1/8 in. ISO Prllel Threds V825B- F8N-S 1/2 in. Femle NPT V824- F2N-S 1/8 in. Femle NPT V824B- F8N-S 1/2 in. Femle NPT T* indictes mximum pnel thickness D : Pnel Hole luminum Br dd-h to the vlve ordering number. Exmple:V824-F-2N-H-S psig End Connection How to Order Select pplicble vlve pttern, options nd body mteril from designtors listed below. V824-F2N -H -B V82B-D4T - -NL -S 2-wy Top mounting : 2-wy ngle pttern TM: top mounting Note: Top mounting option is pplicble only to the in-line pttern 2-wy vlves. Temperture Rnge 10 to 65 C 50 to 150 F mm inch L 39.4 (1.55) 79.5 (3.13) Stinless Br dd-bh to the vlve ordering number. Exmple:V824-F-2N-BH-S Vlve with no lubricnt NL: No lubricnt Vlve L (0.78) 39.6 (1.56) Note: Vlve with no lubricnt is fctory tested t 200 psig (13 br). This vlve hs pressure rting of 200 psig (13 br). Br hndle Nil: Stndrd Nylon hndle H: luminum br hndle BH: Stinless br hndle Body mteril S: SS316 B: Brss Sfe Vlve Selection The selection of vlve for ny ppliction or system design must be considered to ensure sfe performnce. Vlve function, vlve rting, mteril comptibility, proper instlltion, opertion nd mintennce remin the sole responsibillty of the system designer nd the user. Dk Tech ccepts no libility for ny improper selection, instlltion, opertion or mintennce. D Dimensions, mm(in.) 38.9 (1.53) 76.2 (3.00) H (0.44) 17.5 (0.69) T T* 4.8 (3/16) 9.7 (3/8) D 23.1 (29/32) 38.1 (1 1/2) H 42.7 (1.68) 61.7 (2.43) e e

7 V83 Series Swing-Out Bll Vlves Pressure Rting up to 3000 psig (206 br) Ctlog No. V83-3 Oct Fetures Pressure nd temperture compenstion set design. Swing-out design for fst nd esy mintennce with the vlve in-line. Chevron pcking design. 2-wy (on-off) vlves with qurter-turn ctution Two flts on stem (10) nd lever hndle (13) indicte open or closed position of the vlve. Built-in mnul locking device (14) llows locking the vlve with detent either in open or closed position. You my lso pply pd-lock to this device. Pd-lock hole: 8 mm (0.314 in.) 7 6 Bll Set Disc Spring Compenstion set design requires no pressure to crete sel. Under high pressure, sets rect on the bll movement for seling t upstrem nd downstrem. Set Support Ring Flnge Sels Tble 1. Mteril of Construction Vlve Body Mterils Component Stinless steel Crbon Steel Grde / STM Specifiction 1. Body CF8M / WCB 2. Flnges (2) CF8M / WCB 3. Bll 4. Sets (2) 5. Flnge Sels (2) 6. Disc Spring (2) 7. Set support rings (2) 8. Body fsteners (4) 9. Body hex nuts (4) 10. Stem 11. Stem Nuts (2) 12. Tooth Wsher 13. Hndle 14. Locking Device 15. Grounding spring 16. Stem Springs (2) 17. Glnd 18. Pcking Support 19. Upper & Lower Pcking 20. Stem Bering Type 316 / 276 See Tble 2., Optionl FKM O-ring Type 631 Type 316 / 276 SS316 Gr.B8M/ 193 SS316 Gr.8M/ 194 Type 316 / 276, 479 SS316 Stinless steel SS304 with Vinyl sleeve SS304 SS312 / 313 Strin Hrdened SS316 / 240 Type 316 / 276 PEEK (Polyetheretherketone) Reinforced PEEK, Optionl X750 Wetted prts nd lubricnts re listed in blue. Fctory Test Tble 2. Set Mterils Pressure - Temperture Rtings Every vlve is tested with 68.9 br (1000 psig) for lekge t the set to mximum llowble lek rte of 0.1 SCCM. Shell test with 68.9 br (1000 psig) is performed to requirement of no detectble lekge with liquid lek detector. Shell test with wter t 1.5 times the working pressure is performed on request with extr cost. Sets Stndrd Reinforced Virgin Crbon PEEK UHMWPE Vlve Series V83 V83B V83C V83 V83B V83C V83 V83B V83C V83 V83B V83C V83 V83B V83C Pressure -28 to 38 C (-20 to 100 F) 151 br (2200 psig) 103 br (1500 psig) 172 br (2500 psig) 206 br (3000 psig) 172 br (2500 psig) 206 br (3000 psig) 172 br (2500 psig) Mx. Temperture C 100 F C 100 F C 100 F C F C F Lubricnts Silicon bsed nd bsed bsed Hydrocrbon bsed nd bsed

8 Swing-Out Bll Vlves V83 Series PRESSURE-TEMPETURE GRPH Copyright DK TECH CORPORTION. ll Rights Reserved. 2

9 Swing-Out Bll Vlves V83 Series DK-LOK Tube Fitting End Connections Bsic Ordering number Frctionl DK-LOK Metric DK-LOK V83-D4T- V83-D6T- V83B-D8T- V83B-D12T- V83C-D16T- V83-D6M- V83-D8M- V83-D10M- V83B-D12M- End Connection 1/4 in. 3/8 in. 1/2 in. 3/4 in. 1 in. 6 mm 8 mm 10 mm 12 mm mm in L 80.8 (3.18) (4.09) (5.38) 80.8 (3.18) (4.09) L (1.59) (2.04) (2.69) (1.59) (2.04) Dimension H 47.7 (1.88) 64.8 (2.55) 79.0 (3.11) 47.7 (1.88) 64.8 (2.55) H (1.25) (1.25) mm (in.) H (0.66) (1.22) (0.66) (2.25) (4.37) (5.88) 57.2 (2.25) (4.37) B 33.0 (1.30) (1.30) 44.5 V83C-D25M- 25 mm (5.38) (2.69) 79.0 (3.11) (1.22) (5.88) 62.0 Femle Pipe Thred End Connections Bsic Ordering number End Connection Femle NPT Ends V83-F2N- 1/8 in. V83-F4N- 1/4 in. V83B-F6N- 3/8 in. V83B-F8N- 1/2 in. V83C-F12N- 3/4 in. V83C-F16N- 1 in. Femle ISO Tpered Ends V83-F4R- 1/4 in. mm in Dimension mm (in.) L L1 H H1 H (2.18) 68.9 (2.71) 92.0 (3.62) 55.4 (2.18) (1.09) (1.36) (1.81) (1.09) 47.7 (1.88) 64.8 (2.55) 79.0 (3.11) 47.7 (1.88) 31.8 (1.25) (1.25) (0.66) (1.22) (0.66) 57.2 (2.25) (4.37) (5.88) 57.2 (2.25) B 33.0 (1.30) (1.30) V83B-F8R- 1/2 in (2.71) (1.36) 64.8 (2.55) (4.37) 44.5 V83C-F12R- V83C-F16R- 3/4 in. 1 in (3.62) (4.50) (1.81) (2.25) 79.0 (3.11) (1.22) (5.88)

10 Swing-Out Bll Vlves V83 Series Tube nd Pipe Socket Weld End Connections Bsic Ordering number Tube Socket Weld Pipe Socket Weld V83-SW4T- V83-SW6T- V83B-SW8T- V83B-SW12T- V83C-SW16T- V83B-SW8P- V83C-SW12P- V83C-SW16P- End Connection 1/4 in. 3/8 in. 1/2 in. 3/4 in. 1 in. 1/2 in. 3/4 in. 1 in. mm in OD 6.50 (0.26) 9.70 (0.38) (0.51) (0.76) (1.01) (0.86) (1.07) (1.33) X (0.54) (0.67) (0.84) (1.05) (1.31) (1.23) (1.66) (1.78) D 7.1 (0.28) 7.9 (0.31) 9.7 (0.38) 11.2 (0.44) 16.0 (0.63) 9.7 (0.38) 12.7 (0.50) Dimension L L (2.18) 68.9 (2.71) 92.0 (3.62) 68.9 (2.71) 92.0 (3.62) (1.09) (1.36) (1.81) (1.36) (1.81) mm (in.) H H (1.88) 64.8 (2.55) 79.0 (3.11) 64.8 (2.55) 79.0 (3.11) 31.8 (1.25) H (0.66) (1.22) (1.22) 57.2 (2.25) (4.37) (5.88) (4.37) (5.88) B 33.0 (1.30) Pipe Butt Weld End Connections Bsic Ordering number Schedule 10 V83-W4P10- V83B-W8P10- V83C-W12P10- V83C-W16P10- Schedule 40 V83-W4P40- V83B-W8P40- V83C-W12P40- V83C-W16P40- Schedule 80 V83-W4P80- V83-W6P80- V83B-W8P80- V83B-W12P80- V83C-W16P80- End Connection 1/4 in. 1/2 in. 3/4 in. 1 in. 1/4 in. 1/2 in. 3/4 in. 1 in. 1/4 in. 3/8 in. 1/2 in. 3/4 in. 1 in. mm in Dimension mm (in.) OD ID L L1 H H1 H2 B (0.54) (0.84) (1.05) (1.31) (0.54) (0.84) (1.05) (1.31) (0.54) (0.67) (0.84) (1.05) (1.31) (0.41) (0.67) (1.10) 9.20 (0.36) (0.62) (0.82) (1.05) 7.70 (0.30) (0.42) (0.55) (0.74) (0.94) 52.4 (2.06) 68.9 (2.71) 92.0 (3.62) 88.9 (3.50) 52.4 (2.06) 68.9 (2.71) 92.0 (3.62) 88.9 (3.50) 52.4 (2.06) 68.9 (2.71) 88.9 (3.50) (1.03) (1.36) (1.81) (1.03) (1.36) (1.81) (1.03) (1.36) (1.88) 64.8 (2.55) 79.0 (3.11) 47.7 (1.88) 64.8 (2.55) 79.0 (3.11) 47.7 (1.88) 64.8 (2.55) 79.0 (3.11) 31.8 (1.25) (1.25) (1.25) (0.66) (1.22) (0.66) (1.22) (0.66) (1.22) 57.2 (2.25) (4.37) (5.88) 57.2 (2.25) (4.37) (5.88) 57.2 (2.25) (4.37) (5.88) 33.0 (1.30) (1.30) (1.30) Copyright 2007, 2008 DK TECH CORPORTION, ll Rights Reserved. 4

11 Swing-Out Bll 3-Piece Vlves Bll Vlves V83 Series Externl Vent Options The vent pssge is isolted from the bll bore. The vlve in closed position, system fluids vent through vent pssge to the vent port. The vlve in open position, no venting occurs, system fluids flow through the vlve. Choose either the Downstrem Vent (DV) or Upstrem Vent (UP) option. Externl Vented Vlve Rting Upstrem nd downstrem Set Mteril Vlve Series Pressure, br (psi) Mx. Temp. Reinforced Virgin Crbon PEEK UHMWPE V83 V83B V83C V83 V83B V83C V83 V83B V83C to 37 C (-20 to 100 F) C ( F) C ( F) C ( F) C ( F) Mintennce Kits SWING-OUT BOLT Unscrew the swing-out bolt nd loosen other three bolts. This llows users to swing-out the body, keeping the vlve in-line. Set Sel Kits Kit contins ech two pieces of sets, set support rings, disc springs nd flnge sels. Set Mteril Designtor Nil: Reinforced VP: Virgin CP: Crbon PK: PEEK UH: UHMWPE Flnge Sel Designtor Nil: Reinforced VT: FKM O-ring To order, dd - SET s suffix to the ordering number. i.e., V83B-PK-VT-SET Flnge Sel Kits Kit contins two flnge sels. Flnge Sel Designtor Nil: Reinforced VT: FKM O-ring To order, dd - FL s suffix to the ordering number. i.e., V83-VT-FL Pcking Sel Kits Kit contins ech one piece of upper & lower pcking, pcking glnd, pcking support nd stem bering. Pcking Mteril Designtor Nil: Reinforced Stem Bering Designtor PK: PEEK 7: X750 To order, dd - PKG s suffix to the ordering number. i.e., V83B-PK-PKG Fstener Kits Kit contins ech four pieces of body fsteners, body hex nuts nd one stem nut. Vlve Series V83- V83B- V83C- Vlve Series V83- V83B- V83C- Vlve Series V83- V83B- V83C- Vlve Series V83- V83B- V83C- Fstener Mteril Gr. B8M To order, dd - BOLT s suffix to the ordering number. i.e., V83-BOLT ll dimensions shown in this ctlog re for reference only nd re subject to chnge. Dimensions with DK-LOK nuts re in finger-tight position. We reserve the right to chnge specifictions stted in this ctlog for our continuing progrm of improvement. Sfe Vlve Selection The selection of vlve for ny ppliction or system design must be considered to ensure sfe performnce. Vlve function, vlve rting, mteril comptibility, proper instlltion, opertion nd mintennce remin the sole responsibillty of the system designer nd the user. Dk Tech ccepts no libility for ny improper selection, instlltion, opertion or mintennce. 5

12 Swing-Out Bll Vlves V83 Series P series Rck nd Pinion Pneumtic ctutor Model shown: V83 single V83 double V83B double 2-1/8"G ,B dimension V83: V83B: C dimension V83: V83B: Unit: mm C ctutor Mteril of Construction Prts Body Piston (Rck) Drive Shft (Pinion) Spring End Cp O-Ring Tble 3. Double Return 90 Deg. ctutor How to Order Stndrd Mtetil Extruded luminum lloy with externl & internl corrosion protection. Die Cst luminum lloy nodized. Steel lloy Nickel Plted. Spring lloy Steel Nickel Plted. (min. 5, mx. 12 spring) Die Cst luminum lloy Polyester Coted. NBR is stndrd. Optionl FKM nd Silicon. Tble 2. Single Return 90 Deg. ctutor Vlve Ordering Number Dimensions series V83 V83B V83C Vlve series V83 V83B V83C Norml Close PCS1 PCS3 PCS4 Ordering Number PD1 PD1 PD2 Norml Open POS1 POS3 POS4 Weight Unit: Kg L x H x W unit: mm 118x86x x89x x122x94.5 L x H x W unit: mm 118x86x62 118x86x x89x70.5 Weight Kg Moment Vlues P=6 br Nm Tble 1. Technicl Informtion ctutor operting temperture ( o C) Stndrd: NBR O-Ring - 20 to 80. Low Temperture: Silicon O-Ring -40 to 80 (Designtor: LT). High Temperture: FKM O-Ring -15 to 150 (Designtor: HT). ir-pressure: Min. 2.5 br, Mx. 8 br. ir supply end connection: Femle G 1/8 inch (ISO 228-1). Position indictor is stndrd. Mount brcket: Field ssembly kit includes mount brcket, vlve to ctutor connector, specil size of vlve body fsteners, fstener wshers, brcket bolts nd ssembly mnul. Select pplicble vlve pttern, set options, pneumtic ctutor, nd the ctutor temperture option from designtor listed below. V83-D4T - PK - VT -PCS1 -HT -S V83C-D25M - 7 -PD2 -S Moment Vlues P=6 br Nm B ir Consumption Liter ir Consumption Liter Mounting Brcket Ordering Number V83-SMB V83B-SMB V83C-SMB Mounting Brcket Ordering Number V83-DMB V83B-DMB V83C-DMB 58.0 ctutor Operting Temperture Options Nill: Stndrd Temp. LT: Low Temp. HT: High Temp. ctutor Operting Temperture Options Nill: Stndrd Temp. LT: Low Temp. HT: High Temp. Set Mteril Nil: Reinforced VP: Virgin CP: Crbon PK: PEEK UH: UHMWPE Stem Bering Nil: PEEK 7: X750 Flnge Sels Nil: PEEK VT: FKM O-ring Externl Vent UV: Externl Upstrem DV: Externl Downstrem Hndle Nil: Lever Hndle OH: Ovl Hndle Fctory ssembled ctutor Single return, see Tble 2. Double return, see Tble 3. ctutor Temperture Options Nil: Stndrd Temp. LT: Low Temp. HT: High Temp. Body & Flnge Mteril S: 351 CF8M L: 351 CF3M C: 216 Gr. WCB e e

13 V86 Series Bll Vlves, High Pressure 2-wy & 3-wy Bll Vlves VC86 Series CNG Bll Vlves, 2-wy Bll Vlves Ctlog No. V86-7 Mrch 2009 Fetures High pressure up to psi (689 br). Blowout proof design with internlly loded stem. Hndle indictes the flow direction. Positive stop with robust stop pin. High flow rte with mximum orifice. Vrious end ports including Dk-Lok tube port. Vrious flow control with side or bottom inlet port on 3-wy vlves. Optionl Ovl Hndle Tble 1. Mterils of Construction Component Body Bll Set (2) Disc Spring (2) End Sel (2) End Connector (2) Stem Bering Pcking Glnd Lever Hndle Optionl Ovl Hndle Wsher Stem Nut Stop Pin Wetted prts nd lubricnts listed in blue. Fluorinted-bsed lubricnt Vlve Body Mterils SS316/STM 276 or 479 or STM 479 PVDF, stndrd for V86 series PEEK, stndrd for VC86 series TYPE 631 Disc spring, stndrd for VC86 series CNG vlve only. FKM Oring for V86 series HNBR O-ring for VC86 series SS316/ STM 276 or STM 479, stndrd for V86 series PEEK, stndrd for VC86 series Crbon SS316/ STM 276 or STM 479 SS304 hndle with vinyl sleeve SS304 SS304 SS304 ECE R110 Mnul Vlves Clssifiction: Clss 0 Service Pressure: 200 br (2900 psig) Working Pressure: 260 br (3770 psig) Temperture: - 40 to 105 C (-40 to 221 F) VC86 series CNG bll vlves VC86 vlve with live loded compenstion disc spring rects on bll movement for seling t low nd high CNG pressure. VC86 series stndrd PEEK nd PCTFE sets re comptible with CNG. End Connections: Dk-Lok tube port 12 to 16 mm OD (1/2 to 3/4 in. OD) Pipe Thred 1/2 to 1 in.

14 Bll Vlves V86, VC86 Series Opertion 2-wy positive shut off nd 3-wy directionl control of fluids in process, power nd instrument ppliction. Vlves re designed to control fluids in full open or full closed position. Fctory Test Every vlve is tested with nitrogen psig (68 br) for lekge t the set to mximum llowble lek rte of 0.1 SCCM. The stem pcking is tested with nitrogen psig for no detectble lekge. Vlves tht hve not been ctuted for period of time my hve higher initil ctution torque. Vlves must be in open position during system test not to dmge the vlve set. Sour Gs Service NCE MR0175 vilble. Clening nd Pckging Vlves re clened nd pckged in ccordnce with Dk Tech DC-01 clening stndrd. Specil clening for oxygen service is vilble on request. 2-Wy On-Off Vlves Pressure/Temperture Rtings V86 2-wy vlve with PEEK set psig V86 8,000 br SQ 6,000 V86B, V86C 413 L 4, V86D series 2, Vlve Ordering Informtion nd Dimensions Bsic Ordering Number V86- V86B- VC86B- V86C- VC86C- V86D- VC86D- D-4T D-6T D-8T F-4N F-6N F-8N M-4N M-6N M-8N F-8N F-12N D-12M D-16M D-8T D-10T D-12T F-12N F-16N D-12T D-16T M-12N M-16N End Connections Inlet & Outlet 1/4 in. Dk-Lok 3/8 in. Dk-Lok 1/2 in. Dk-Lok 1/4 in. Femle NPT 3/8 in. Femle NPT 1/2 in. Femle NPT 1/4 in. Mle NPT 3/8 in. Mle NPT 1/2 in. Mle NPT 1/2 in. Femle NPT 3/4 in. Femle NPT 12mm Dk-Lok 16mm Dk-Lok 1/2 in. Dk-Lok 5/8 in. Dk-Lok 3/4 in. Dk-Lok 3/4 in. Femle NPT 1 in. Femle NPT 3/4 in. Dk-Lok 1 in. Dk-Lok 3/4 in. Mle NPT 1 in. Mle NPT * V86D body is round br construction. CNG vlve ordering number : The bsic ordering number listed in blue represents VC86 s well s V86 series bll vlve. mm ( in. ) 4.8 ( 0.19) 7.1 ( 0.28) 10.0 ( 0.39) 7.1 ( 0.28) 10.0 ( 0.39) 12.7 ( 0.50) 10.0 ( 0.39) 12.7 ( 0.50) 10.4 ( 0.41) 12.7 ( 0.50) 19.0 ( 0.75) 15.7 ( 0.62) 19.0 ( 0.75) 15.7 ( 0.62) 19.0 ( 0.75) C F Dimensions mm ( in. ) H L SQ ( 3.78) ( 4.04) ( 4.24) ( 2.91) ( 4.26) ( 1.52) ( 3.03) ( 1.26) ( 3.35) ( 3.76) ( 3.76) ( 3.94) ( 3.50) ( 3.54) ( 4.33) ( 4.56) ( 5.86) ( 2.00) ( 1.57) ( 4.33) ( 5.86) 56.0 ( 2.20) ( 4.56) ( 4.52) ( 4.25) ( 5.00) ( 4.92) ( 5.27) ( 4.68) ( 5.07) F-16N 1 in. Femle NPT 25.0 ( 0.98) Full Bore ( 5.20) ( 3.31) ( 4.44) 80.0*( 3.15) Tble 2. 2-Wy Vlve ctution Torque System Pressures, br (psig) Vlve 0 (0) 344 (5000) Series Torque Unit: Nm ( ) V86 V86B V86C 3.92 ( 2.89) 7.35 ( 5.42) ( 9.04) ( 7.59) ( 14.62) 50.0 ( 1.97) 413 (6000) lbs-ft 6.37 ( 4.69) , DK TECH CORPORTION, ll Right Reserved.

15 R Bll Vlves V86, VC86 Series 3-wy Diverter Vlves SIDE PORT INLET 1/4 turn ctution Outlet 86 Series Outlet SQ H SQ Outlet Outlet BOTTOM PORT INLET 1/2 turn ctution H1 H1 L Inlet L Inlet V86 3-wy bll vlve is designed to switch medi through the inlet port nd direct it to out of two outlet ports. Ordering Informtion nd Dimensions Bsic Ordering Number End Connections 3*- D-4T- 1/4 in. Dk-Lok 3*- D-6T- 3/8 in. Dk-Lok V86-3*- D-8T- 1/2 in. Dk-Lok 3*- F-4N - 1/4 in. Femle NPT 3*- F-6N- 3/8 in. Femle NPT 3*- F-8N- 1/2 in. Femle NPT 3*- F-8N- 1/2 in. Femle NPT V86B- 3*- F-12N- 3/4 in. Femle NPT 3*- D-10T- 5/8 in. Dk-Lok 3*- D-12T- 3/4 in. Dk-Lok 3*- D-12T- 3/4 in. Dk-Lok V86C- 3*- D-16T- 1 in. Dk-Lok 3*- F-12N- 3/4 in. Femle NPT 3*- F-16N- 1 in. Femle NPT ll dimensions shown re for reference only nd re subject to chnge. mm ( in. ) 4.8 ( 0.19) 7.1 ( 0.28) 10.0 ( 0.39) 12.7 ( 0.50) 15.7 ( 0.62) 19.0 ( 0.75) Dimensions mm ( in. ) H H1 L 50.9 ( 2.00) 96.0 ( 3.78) 53.0 ( 2.09) ( 4.04) ( 4.26 ) ( 1.52 ) ( 5.86 ) ( 5.86 ) 51.0 ( 2.00 ) 56.0 ( 2.20 ) 55.8 ( 2.20) 40.0 ( 1.57) 41.5 ( 1.64) 45.5 ( 1.79) 55.0 ( 2.17) 55.0 ( 2.17) 67.2 ( 2.66) 67.7 ( 2.66) 75.3 ( 2.96) 80.0 ( 3.15) 59.5 ( 2.34) 67.0 ( 2.64) ( 4.24) 74.0 ( 2.91) 77.0 ( 3.03) 85.0 ( 3.35) 89.0 ( 3.5 ) 90.0 ( 3.54) ( 4.5 ) ( 4.52) ( 4.92) ( 5.27) 96.0 ( 3.78) ( 4.37) SQ 32.0 ( 1.26) 40.0 ( 1.57) 50.0 ( 1.97) Side nd Bottom Port Vlve Ordering Informtion To order side port entry vlve, replce * with S, to order bottom port entry vlve, replce * with B. Exmples: V86-3S-D-4T-S, V86-3B-D-4T-S. Tble 3. 3-wy Vlve ctution Torque System Pressures, br (psig) Vlve 0 (0) 206 (3000) 275 (4000) Series Torque Unit: Nm (Ibs-ft) V ( 2.89) ( 4.69) V86B 7.35 ( 5.42) 7.85 ( 5.78) - Tble 4. 2-wy Vlve Pressure nd Temperture Rting Vlve Series V86 V86B V86C V86D Set PVDF PCTFE PEEK PVDF PCTFE PEEK PCTFE llowble Working Pressure t mbient temperture psig(br) 6,000 (413) 10,000 (689) 5,000 (344) 6,000 (413) 5,000 (344) Temperture Rting -30 to 130 (-22 to 266 ) -30 to 180 (-22 to 356 ) -40 to 230 (-40 to 446 ) -30 to 110 (-22 to 230 ) -30 to 160 (-22 to 320 ) -40 to 210 (-40 to 410 ) -30 to 160 (-22 to 320 ) Tble 5. 3-wy Vlve Pressure nd Temperture Rting Vlve Series V86 V86B V86C Set PVDF PCTFE PEEK PVDF PCTFE PEEK llowble Working Pressure t mbient temperture psig(br) 4,000 (275) 6,000 (413) 3,000 (206) 4,000 (275) Temperture Rting -30 to 130 (-22 to 266 ) -30 to 180 (-22 to 356 ) -40 to 230 (-40 to 446 ) -30 to 110 (-22 to 230 ) -30 to 160 (-22 to 320 ) -40 to 210 (-40 to 410 ) 3

16 R Bll Vlves V86, VC86 Series Options Locking Nut Pnel Mounting Ordering designtor : P1 ddition locking nut below hndle mkes the vlve pnel mountble. Disssemble the hndle prior to pnel mounting. mm ( in. ) Vlve Series Pnel Thickness Pnel Hole Drill Locking Nut V ( 1.18) V86B 38.0 ( 1.50) Mx. 4.0 ( 0.157) Pnel V86C 38.0 ( 1.50) Screw Hole Pnel Mounting Ordering designtor : P2 dditionl four (4) screw holes on the top of vlve mkes the vlve pnel mountble. Disssemble the hndle prior to pnel mounting. mm ( in. ) Vlve Series V86 V86B V86C L L1 t T 34.0 ( 1.33) 36.0 ( 1.42) 40.0 ( 1.57) 26.0 ( 1.02) 29.0 ( 1.14) 35.0 ( 1.37) 4.0 ( 0.15) 5.0 ( 0.20) 6.0 ( 0.23) 30.0 ( 1.18) 38.0 ( 1.50) 38.0 ( 1.50) L L1 T t 86 Series "Lift-Turn" Locking Device Ordering designtor : LD Dk Tech ptented "Lift-Turn" sfety locking device llows you to lock the vlve mnully either in open or close position. The locking device consists of study upper nd lower locking detents mde out of stinless steel. Pd-Lock pplicble 7.2 mm (0.28 in) hole constructed on upper locking detent. You my pply pd-lock to secure the vlve in the open or close position. Note: This option is pplicble to 2-wy vlves. Ordering Informtion Select the desired bsic ordering number, nd options from designtors listed below. V86-D-4T V86B-F -12N VC86B-D-12M -PC - OH -S -LD -S -S Set Nil: PEEK, stndrd for VC86B, VC86C series Nil: PCTFE, stndrd for VC86D series Nil: PVDF, stndrd for V86 series PC: PCTFE PK: PEEK PD: PVDF Pnel Mounting P1: Locking nut pnel mounting P2: Screw hole pnel mounting Locking Device LD: Locking Device Hndle Nil: Stndrd Lever Hndle OH: Ovl Hndle OH option is pplicble to 2-wy V86 series vlves. Vlve Mteril S316 Sfe Vlve Selection The selection of vlve for ny ppliction or system design must be considered to ensure sfe performnce.vlve function, vlve rting, mteril comptibility, proper instlltion, opertion nd mintennce remin the sole responsibillty of the system designer nd the user. Dk Tech ccepts no libility for ny improper selection, instlltion, opertion or mintennce. e e

17 VH86 series High Pressure Multi Purpose Bll Vlves Ctlog No. VH86-4 Oct Fetures High flow in compct design. High pressure cpcity designed for blow-out proof with internlly loded bll stem. Micro-finished bll provides positive sel. 90 degree ctution for 2-wy nd 180 degree ctution for 3-wy bll vlves. Pnel mounting s stndrd. Chevron stem sel, djustble with the hndle disssembled. Hndle indictes flow direction. Low operting torques nd positive hndle stops. Optionl pneumtic ctution. Mteril of Construction Components 1. Hndle 2. Set Screw 3. Pnel Nut 4. Pcking bolt* 5. Upper / Lower Glnd 6. Stem Chevron Pcking 7. Stem 8. Body 9. Bll 10. Set (2) 11. Retiner (2) 12. Retiner Sel (2) 13. End Connector Sel (2) 14. End Connector (2) Vlve Body Mteril Stinless Steel Grde/STM Specifiction Nylon with brss insert Stinless steel SS316/276 /D1710 type 1, Grde 1, Clss B SS316/276 SS316/276 Type F316 SS316/276 Stndrd PCTFE (Kel-F), optionl, PEEK SS316/276 /D1710 type 1, Grde 1, Clss B SS316/276 * Molybdenum disulfide with hydrocrbon coting Wetted prts nd lubricnts re listed in blue. Lubricnt is Fluorinted-bsed. Opertion nd Pcking djustment VH86 vlves re designed to control fluid in full open nd closed position, using VH86 vlves to throttle the flow my reduce the vlve life. Stem pcking cn be djustble with the hndle disssembled. Tighten pcking bolt clockwise to tighten the stem pcking. Vlves tht hve not been ctuted for period of time my hve higher initil ctution torque. If the vlve system needs to be tested t higher pressure thn the vlve mximum pressure, the vlve must be in open position during the test so s not to dmge the vlve set. Optionl Sour Gs Service pplicble. ppliction VH86 series bll vlve offers sfe nd relible performnce in wide rnge of onshore nd offshore pplictions: Wter, oil, gs, petrochemicl in hevy duty pplictions. Fctory Test, Clening nd Pckging Every vlve is fctory tested with nitrogen gs t 1000 psig (68.9 br) for lekge t set to mximum llowble lek rte of 0.1 SCCM. The pcking is tested with nitrogen gs for no detectble lekge. Every vlve is clened nd pckged in ccordnce with DK clening stndrd DC-01.

18 Vlves VH86 Series Multi Purpose Bll Vlves Bi-directionl 2-wy Bll Vlves Technicl Dt Vlve Series VH86, VH86B, nd VH86C series Set PCTFE PEEK Seling Mterils Stem Pcking Retiner / End Sel Pressure to 37 O C (-20 to 100 O F) 6000 psig (413 br) 6000 psig (413 br) 1500 psig (103 br) Temperture Rting -30 to 180 O C (-22 to 355 O F) -54 to 230 O C (-65 to 446 O F) -30 to 176 O C (-22 to 349 O F) PCTFE is stndrd set mteril. Ordering Informtion nd Dimensions Bsic Ordering Number D-1T- D-2T- F-2N- M-2N- D-4T- M-4N- D-3M- D-2T- D-4T- MD-4N4T- FD-4F4T- F-4N- M-4N- MF-4N- MD-4N6T- FD-4N6T- D-6T- M-6N- D-6M- D-8M- D-10M- F-6N- F-8N- D-8T- M-8N- D-12T- D-12M- D-16M- VH86C- VH86B- VH86- End Connections Inlet Outlet mm inch 1/16 Dk-Lok 1/8 Dk-Lok 1/8 Femle NPT 1/8 Mle NPT 1/4 Dk-Lok 1/4 Mle NPT 3mm Dk-Lok 1/8 in. Dk-Lok 1/4 in. Dk-Lok 1/4 in. Mle NPT 1/4 in. Femle NPT 1/4 in. Dk-Lok 1/4 in. Dk-Lok 1/4 in. Femle NPT 1/4 in. Mle NPT 1/4 in. Femle NPT 3/8 in. Dk-Lok 3/8 in. Dk-Lok 1/4 in. Mle NPT 1/4 in. Mle NPT 1/4 in. Femle NPT 3/8 in. Dk-Lok 3/8 in. Mle NPT 6 mm Dk-Lok 8 mm Dk-Lok 10 mm Dk-Lok 3/8 in. Femle NPT 1/2 in. Femle NPT 1/2 in. Dk-Lok 1/2 in. Mle NPT 3/4 in. Dk-Lok 12 mm Dk-Lok 16 mm Dk-Lok (1.8) 38.4 (1.51) 45.7 (1.8) 82.2 (3.24) 89.0 (3.50) 90.4 (3.56) 92.0 (3.62) 99.0 (3.90) (4.30) (4.68) (4.44) (4.66) mm (in.) ll dimensions shown re for reference only nd re subject to chnge. Dimensions with DK-LOK nuts re in finger-tight position Dimensions L1 L2 H1 H (1.30) 34.5 (1.36) 27.2 (1.07) 30.0 (1.18) 37.6 (1.48) 34.3 (1.35) 34.8 (1.37) 41.9 (1.65) 38.4 (1.51) 41.1 (1.62) 38.4 (1.51) 33.0 (1.30) 34.5 (1.36) 27.2 (1.07) 30.0 (1.18) 37.6 (1.48) 34.3 (1.35) 34.8 (1.37) 41.9 (1.65) 41.1 (1.62) 38.4 (1.51) 38.4 (1.51) 41.1 (1.62) 8.4 (.33) 10.7 (.42) 17.5 (.69) 9.5 (.37) 11.9 (.47) 17.8 (.70) H 24.8 (.98) 38.9 (1.53) 19.1 (.75) 25.4 (1.00) 38.1 (1.50) D 14.7 (.58) 19.6 (.77) 22.9 (.90) T 3.3 (.13) 6.4 (.25) 9.7 (.38) , DK TECH CORPORTION. ll Right Reserved.

19 Vlves 3-wy Diverter Bll Vlves VH86 Series Multi Purpose Bll Vlves Pressure-Temperture Curve VH86 3-wy Bll Vlve is designed to switch medi through the bottom port nd direct it to out of two outlet ports. Legend: 2W:2-Wy VH86 bll vlves 3W:3-Wy VH86 bll vlves Technicl Dt Vlve Series VH86-3B VH86B-3B VH86C-3B Set PCTFE PEEK PCTFE PEEK Seling Mterils Stem Pcking Retiner / End Sel Pressure to 37 O C (-20 to 100 O F) 6000 psig (413 br) 6000 psig (413 br) 1500 psig (103 br) 4000 psig (275 br) 6000 psig (413 br) 1500 psig (103 br) Temperture Rting O C ( O F) -30 to 180 (-22 to 355) -54 to 230 (-65 to 446) -30 to 176 (-22 to 349) -50 to 180 (-58 to 355) -54 to 230 (-65 to 446) -30 to 176 (-22 to 349) Ordering Informtion nd Dimensions Bsic Ordering Number End Connections VH86B-3B- VH86-3B- VH86C-3B- D-1T- 1/16 Dk-Lok D-2T- 1/8 Dk-Lok F-2N- 1/8 Femle NPT M-2N- 1/8 Mle NPT D-4T- 1/4 Dk-Lok M-4N- 1/4 Mle NPT D-2T- 1/8" Dk-Lok D-4T- 1/4" Dk-Lok F-4N- 1/4" Femle NPT DDM-4T4N-* 1/4" Dk-Lok,1/4" Mle NPT M-4N- 1/4" Mle NPT D-6T- 3/8" Dk-Lok M-6N- 3/8" Mle NPT D-6M- 6 mm Dk-Lok D-8M- 8 mm Dk-Lok D-10M- 10 mm Dk-Lok F-6N- 3/8" Femle NPT F-8N- 1/2" Femle NPT D-8T- 1/2" Dk-Lok DDF-8T8F-* 1/2" Dk-Lok,1/2" Femle NPT M-8N- 1/2" Mle NPT D-12T- 3/4" Dk-Lok D-12M- 12 mm Dk-Lok D-16M- 16 mm Dk-Lok Dimensions mm (in.) mm Inch H2 H (.33) (.94) ll dimensions shown re for reference only nd re subject to chnge. Dimensions with DK-LOK nuts re in finger-tight position. L (1.30) 34.5 (1.36) 27.2 (1.07) 30.0 (1.18) 37.6 (1.48) 34.3 (1.35) 41.9 (1.65) 38.4 (1.51) 41.1 (1.62) 45.7 (1.8) 41.1 (1.62) (1.78) 46.0 (1.81) 49.5 (1.95) 54.6 (2.15) 59.4 (2.34) 56.4 (2.22) 59.2 (2.33) 56.9 (2.33) L (1.30) 34.5 (1.36) 27.2 (1.07) 30.0 (1.18) 37.6 (1.48) 34.3 (1.35) 41.9 (1.65) 38.4 (1.51) 41.1 (1.62) 45.7 (1.8) 41.1 (1.62) (1.78) 46.0 (1.81) 49.5 (1.95) 54.6 (2.15) 59.4 (2.34) 56.4 (2.22) 59.2 (2.33) 56.9 (2.33) H (1.39) 36.8 (1.45) 29.2 (1.15) 32.0 (1.26) 39.6 (1.56) 36.3 (1.43) 45.5 (1.79) 47.8 (1.88) 41.9 (1.65) 47.8 (1.88) 44.7 (1.76) 49.3 (1.94) 44.7 (1.76) 47.8 (1.88) 48.5 (1.91) 49.5 (1.95) 58.2 (2.29) 63.2 (2.49) 68.1 (2.68) 63.2 (2.49) 65.8 (2.59) 68.1 (2.68) 67.8 (2.67) 65.5 (2.67) 11.9 (.47) 17.8 (.70) 38.9 (1.53) 19.1 (.75) 25.4 (1.00) 38.1 (1.50) * VH86 3-wy bll vlves re described by first the outlet ports (1) nd (2) nd next the bottom inlet port (3). 1 D 14.7 (.58) 19.6 (.77) 22.9 (.90) 3 T 3.3 (.13) 6.4 (.25) 9.7 (.38) 2 3

20 Vlves VH86 Series Multi Purpose Bll Vlves P series Rck nd Pinion Pneumtic ctutor Model shown: VH86B/C series dimension VH86B: VH86C: B dimension VH86B: VH86C: Unit: mm ctutor Mteril of Construction Prts Body Piston (Rck) Drive Shft (Pinion) Spring End Cp O-Ring Tble 2. Single Return 90 Deg. ctutor Vlve Ordering Number Dimensions series VH86 VH86B VH86C Tble 3. Double Return 90 Deg. ctutor Vlve series VH86 VH86B VH86C Norml Close PCS1 PCS2 Ordering Number PD1 How to Order Stndrd Mtetil Extruded luminum lloy with externl & internl corrosion protection Die Cst luminum lloy nodized. Steel lloy Nickel Plted. Spring lloy Steel Nickel Plted. (min. 5, mx. 12 spring) Die Cst luminum lloy Polyester Coted. NBR is stndrd. Optionl FKM nd Silicon. Norml Open POS1 POS2 Weight Unit: Kg 0.75 L x H x W unit: mm 118x86x62 L x H x W unit: mm 118x86x62 Weight Kg 0.9 Moment Vlues P=6 br Nm 14.4 Tble 1. Technicl Informtion ctutor operting temperture ( o C) Stndrd: NBR O-Ring - 20 to 80. Low Temperture: Silicon O-Ring -40 to 80 (Designtor: LT). High Temperture: FKM O-Ring -15 to 150 (Designtor: HT). ir-pressure: Min. 2.5 br, Mx. 8 br. ir supply end connection: Femle G 1/8 inch (ISO 228-1). Position indictor is stndrd. Moment Vlues P=6 br Nm ir Consumption Liter Mounting Brcket Ordering Number VH86-SMB VH86B-SMB VH86C-SMB Select pplicble vlve pttern, set options, pneumtic ctutor, nd the ctutor temperture option from designtor listed below. VH86B-D-6T- - PK - PCS1 -HT -S VH86C-D-12T - SG -S ir Consumption Liter 0.1 Mounting Brcket Ordering Number VH86-DMB VH86B-DMB VH86C-DMB Mount brcket: Field ssembly kit includes mount brcket, vlve to ctutor, brcket bolts nd ssembly mnul. ctutor Operting Temperture Options Nill: Stndrd Temp. LT: Low Temp. HT: High Temp. ctutor Operting Temperture Options Nill: Stndrd Temp. LT: Low Temp. HT: High Temp. Set Mteril Nil: PCTFE PK: PEEK PE: Sour Gs SG: Sour Gs Fctory ssembled ctutor For single return, see Tble 2. For double return, see Tble 3. ctutor Temperture Options Nill: Stndrd Temp. LT: Low Temp. HT: High Temp. Vlve Body Mteril S: S316 Sfe Vlve Selection The selection of vlve for ny ppliction or system design must be considered to ensure sfe performnce. Vlve function, vlve rting, mteril comptibility, proper instlltion, opertion nd mintennce remin the sole responsibillty of the system designer nd the user. Dk Tech ccepts no libility for ny improper selection, instlltion, opertion or mintennce. e e