Solution Partner. Leak - Proof. Flow & Control. Ball Valves SBV10 SBV30 SBV60 SFBV60. W e. s u p p o r t. t h e

Transcription

1 W e. s u p p o r t. t h e i n n o v a t i o n s. o f. c u s t o m e r s Leak - Proof The Best Partner Flow & Control Solution Partner for Value Creation Ball Valves SBV SBV30 SBV60 SFBV60

2 SBVSeries For working pressure up to 00 psig(69bar) Features Compact design with hexagon bar-stock for high integrity. Working pressure up to 00psig(69bar) at 038 Low torque quarter turn actuation. Size range of from 1/4to 1tubing and piping Various end connections : reliable S-LOK, NPT & ISO male & female. Butterfly handle is available as an option. Pressure-Temperature Ratings Pressure, psig Pressure, bar Temperature pplications Water, Oil, Gas. Petrochemical Plants. Steel mils. Heavy Vehicles. Factory Test Every valve is factory tested with Nitrogen@00psig (69bar) for leakage at the seat to a maximum allowable leak of 0.1sccm. The stem packing is tested for no detectable leakage. 15

3 H L L B Item Description Body End Connector Ball Seat Insert Stem Lower Packing Upper Packing Grand Grand Washer Spring Washer Lock Nut Handle Material/ STM Specification S316 Brass S316/ 479, 276 Brass/ B16 S316/ 479, 276 Brass/ B16 S316/479 Reinforced S316/479 S316/479 Reinforced Reinforced S304 S304 S304 S304 S430 Ordering Information and Dimensions Basic Ordering Number S-6M SBV F-4N S-M SBV S-6T F-6N S-12M SBV S-8T S-16M S-T SBV F-12N S-16T SBV F-16N Orifice mm(in) Ordering Information End Connections Inlet/ Outlet 6mm S-LOK 1/4S-LOK 1/4Female NPT mm S-LOK 3/8S-LOK 3/8Female NPT 12mm S-LOK 1/2S-LOK 1/2Female NPT 16mm S-LOK 5/8S-LOK 3/4Female NPT 3/4S-LOK 1S-LOK 1Female NPT Select valve ordering number, and applicable options. SBV F 4N Dimensions(mm) L H B BF S6 Series by Orifice Size End Connection Inlet-Outlet Size Handle Nil :#Standard lever handle BF: Optional butterfly handle Body Material S6 :#316 Stainless Steel BS: Brass SFETY in VLVE SELECTION The selection of a valve for any application or system design must be considered to ensure safe performance. Valve function, valve rating, material compatibility, proper installation,operation and maintenance remain the sole responsibility of the system designer and the user. HNSUN ENGINEERING accepts no liability for any improper selection, installation, operation or maintenance. 16

4 SBV30Series For working pressure up to 3000 psig(206bar) 1. Handle with rrow indicates flow direction. allows quick operation to open and close. 2. Panel Mounting Nut allow easy installation. 3. Variety of End Connections include fractional/metric S-LOK tube fittings, NPT female, ISO female threads. 4. One-piece body reduces the number of potential leak points. 5. Orifice is optimized design for minimum pressure drop. 6. Packing Bolt allows easy packing adjustment with valve in-line. 7. Packing is supported by top and bottom glands. 8. Encapsulating Ball Seats virtually allow no dead volume. are uniformly forced to form tight seals against ball and body cavity. 9. Support rings and discs retains the capsule packing and prevent cold flow.. Integral Ball-Stem is machined from one piece bar stock. is best suited to encapsulate ball seats. Features Pressure rating up to Temperature rating from!(") to 1!(65") with standard seat and packing. Choice of materials : Standard S316 and available in alloy 400 and Brass. Vent to atmosphere available Every valve is 0% factory tested with the (69bar). Technical Data Materials of construction Description 1 Handle 2 Set screw 3 Packing bolt 4 Upper grand 5 Packing 6 Lower grand 7 & 7-a Upper&Lower Ball seat 8 Ball stem 9 Support rings Side discs 11 Panel nut 12 Body Grade / STM Specification Valve Body Materials S316 Brass Black Nylon 17-4PH/564 S316/479, 276 Brass/B16 S316/479, 276 /D17 S316/479, 276 Brass/B16 /D17 S316/479, 276 S316 (Fluorocarbon-coated) S316 /479, 276 Brass/B16 Pressure Rating with standard seat Valve SBV 1 SBV 2 SBV 3 SBV 4 Straight 2-way 3000psig (206bar) 20psig (172bar) ngle 2-way 20psig (172bar) 20psig (172bar) psig (3bar) Switching 3-way Temperature Range to 1 ( to 65 17

5 2-Way (Shut-Off Valve) Straight Pattern F ngle Pattern F T1 Max.Panel Thick. G-Panel Drill Hole H T1 Max.Panel Thick. T2 Min.Panel Thick. G-Panel Drill Hole H H1 H2 T2 Min.Panel Thick. H2 L1 L2 W SHUT OFF SHUT OFF B H3 Ordering Information and Dimensions Basic Ordering Number S-1T S-2T S-3M SBV1 S-6M F-2N S-6T S-6M SBV2 S-8M F-2N F-4N M-4N F-4R S-6T S-M SBV3 F-4N F-6N F-6R S-8T SBV4 S-12M F-8R Orifice mm inch Inline ngle End Connections Inlet Outlet 1/16S-LOK 1/8 S-LOK 3mm S-LOK 1/4 S-LOK 6mm S-LOK 1/8Female NPT 1/4 S-LOK 3/8 S-LOK 6mm S-LOK 8mm S-LOK 1/8Female NPT 1/4Female NPT 1/4Male NPT 1/4ISO Female Tapered 3/8 S-LOK mm S-LOK 1/4Female NPT 3/8Female NPT 3/8ISO Female Tapered 1/2 S-LOK 3/4 S-LOK 12mm S-LOK 1/2Female NPT 1/2ISO Female Tapered Dimensions(mm) L1 L2 H3 H2 H1 F T1 T2 G H W ll dimensions shown are for reference only and are subject to change. Dimensions with S-LOK nuts are in finger-tight position. Patterns : To order angle pattern, use- as a suffix to the basic ordering number. Example : SBV1---S Flow Rate Pressure Drop to tomosphere(p) in psi ir SCFM Water US GPM The is for the straight pattern valves, s of angle pattern valves are the same as those of 3-way valves

6 3-Way switching Valves F T1 Max.Panel Thick. T2 Min.Panel Thick. G-Panel Drill Hole H H1 H2 T panel : 3.2mm(1/8inch) minimum panel thickness. H1 L1 W Ordering Information and Dimensions Basic Ordering Number S-1T S-2T SBV1-3B S-3M S-6M F-2N S-6M SBV2-3B S-8M F-4N F-4R S-6T S-M SBV3-3B F-4N F-6N F-6R S-8T SBV4-3B S-12M F-8R Orifice mm inch End Connections 1/16S-LOK 1/8 S- LOK 1/4 S-LOK 3 mm S-LOK 6mm S-LOK 1/8Female NPT 1/4 S-LOK 6mm S-LOK 8mm S-LOK 1/4Female NPT 1/4ISO Female Tapered 3/8 S-LOK mm S-LOK 1/4Female NPT 3/8Female NPT 3/8ISO Female Tapered 1/2 S-LOK 3/4 S-LOK 12mm S-LOK 1/2Female NPT 1/2ISO Female Tapered Dimensions(mm) L1 H1 H2 F T1 T2 G H W ll dimensions shown are for reference only and are subject to change. Dimensions with S-LOK nuts are in finger-tight position. Flow Rate Pressure Drop to tomosphere(p) in psi 0.08 ir Water US

7 Packing djustment SBV30 valves are designed to control fluid in full open and closed position ; using SBV30 valves to throttle the flow may reduce the valve life. Every valves are factory adjusted for 00psig service at 7021 For use in higher pressure, the packing must be readjusted. Exposure of valves to varying temperature can affect the initial packing load. You may need check leak and readjust packing bolt. Packing adjustment may be required during the valve in service. Vent Hole Option : Downstream vent hole is open used with instrument or gauges. When the valve is in the on position, pessure is applied to the Gauge or instrument. When the valve is turned off, the instrument or gauge is vented to atmosphere through a hole in the side of the valve body and upstream port is closed to fluid flow. The maximum working pressure of the valve with the vented hole Option is limited to 0psig(34bar). Testing Every valve is factory tested for bubble-tight leakage at both seat and stem packing with nitrogen at 00psi(69bar). Seats have a maximum allowable leak rate of 0.1sccm. Optional tests are available upon request. Ordering Information SBV1 S 4T VH G S6 Series by Orifice Size End Connection Inlet-Outlet Size Pattern Nil : 2-way straight : 2-way angle Vent Hole Nil :#Standard VH : Vent Hole Handle Color Nil:#Standard Black Nylon B :#Blue G :#Green R :#Red Y :#Yellow Body Material S6 :#316 Stainless Steel BS : Brass SFETY in VLVE SELECTION When selecting a valve, the total system design must be considered to ensure safe, trouble-free performance. Valve function, materials compatibility, adequate ratings, proper installation, operation, and maintenance are the responsibility of the system designer and user. 20

8 SBV60Series High Pressure Ball Valves Features Pressure rating up to,000psig Temperature rating from to 26530with PVDF seat or from to 0 with PEEK seat. Robust body is best suited for high pressure application and allows various pattern including: 2-way straight pattern, 3-way side port inlet, 3-way bottom port inlet. Panel mounting and locking devices are available as options. Blow out proof design with internally loaded stem. Floating ball design ensures leak proof shut-off at high pressure. Straight through flow path for minimum pressure drop. Variety of end connedtions include reliable S-LOK tube fittings, Male/female NPT & ISO/BSP threads. Handle with PVC Color coated allows easy and quick operation with low torque. 90 degree actuation. Every valve is 0% factory tested with the (69bar). Optional sour Gas service to NCE MR Operation HNSUN SBV60 Series ball valves provide quick 1/4 turn on-off control of fluids in process, power and instrumentation applications. ll ports are suitable as inlets in full operation pressure of the valve. broad selection of valve body, seat, and seal materials provide a wide range of pressure and temperatures at which the valve may be used. Valves that have not been actuated for a period of time may have a higher actuation torque. Materials of Construction Item Description Body End Connector Ball End Seals Seats Stem Grade/STM Specification S316/276, 479 S316/276, 479 S316/276 Fluorocarbon FKM O-ring PVDF, optional PCTFE, PEEK S316/276, Stem Packing Pin Lock Nut Handle /D17 Stainless Steel Stainless Steel with Washer S304 with PVC Coating Note : wetted parts are listed in orange color. Lubricant is Fluorocarbon based. 21

9 C C H H1 d d 2-Way Panel Thickness 3/8max. L B L B psig,000 bar 689 with Panel Mounting SBV60 2-way Pressure-Temperature Curves for valves with PEEK seat 8,000 6,000 SBV2H, 3H SBV1H SBV60Series S 4, , Ordering Information and Dimensions Basic Ordering Number S-6T S-8T F-4N SBV1H F-6N M-4N M-6N M-8N F-12N SBV2H M-12N S-T F-12N F-16N SBV3H S-16T M-12N M-16N Orifice mm(inch).0(0.39) 12.7(0.) 19.0(0.75) End Connections 1/4S-LOK 3/8S-LOK 1/2S-LOK 1/4Female NPT 3/8Female NPT 1/2Female NPT 1/4Male NPT 3/8Male NPT 1/2Male NPT 1/2Female NPT 3/4Female NPT 3/4Male NPT 5/8S-LOK 3/4S-LOK 3/4Female NPT 1 Female NPT 3/4S-LOK 1 S-LOK 3/4Male NPT 1 Male NPT d mm Dimensions(mm) B L H H1 C S ll dimensions shown are for reference only and are subject to change. Dimensions with S-LOK nuts are in finger-tight position

10 3-Way Ordering Information and Dimensions 2-way Basic Ordering Number SBV1H-3 SBV2H-3 SBV3H-3 PVDF PCTFE PEEK PVDF PCTFE PEEK S-6T S-8T F-4N F-6N F-12N S-T S-16T F-12N F-16N End Connections Inlet & Outlet 1/4S-LOK 3/8S-LOK 1/2S-LOK 1/4Female NPT 3/8Female NPT 1/2Female NPT 1/2Female NPT 3/4Female NPT 5/8S-LOK 3/4S-LOK 3/4S-LOK 1 S-LOK 3/4Female NPT 1 Female NPT 6,000psig(413bar),000psig(689bar) 5,000psig(344bar) 6,000psig(413bar) Orifice mm(inch).0(0.39) 12.7(0.) 19.0(0.75) 60.8 ll dimensions shown are for reference only and are subject to change. Dimensions with S-LOK nuts are in finger-tight position. Ordering information :Sfor side entry 3-way ordering i.e., SBV1H-3S-S-8T,Bfor bottom entry 3-way ordering i.e., SBV1H-3B-S-8T Handle Turn torque Table (N.m) Valve Series SBV1H SBV2H SBV3H 0(0 ) 0.30(0.22) 1.20(0.88) 1.70(1.25) 69(00) 0.35(0.25) 1.(1.) 1.80(1.32) Technical Data-Pressure and Temperature Rating Valve Series SBV1H SBV2H SBV3H Sealing Materials Seat Stem End Packing Seal FKM FKM Pressure Temperature Rating -30 to 130 (-22 to to 180 (-22 to to 230 (-65 to to 1 (-9 to to 160 (-9 to to 2 (-31 to 4 d mm pplied Working Pressurespsig(bar) 137(2000) 0.40(0.29) 1.70(1.25) 1.90(1.40) 3-way Valve Series SBV1H SBV2H SBV3H 206(3000) 0.40(0.29) 1.70(1.25) 2.00(1.47) PVDF PCTFE PEEK PVDF PCTFE PEEK Dimensions mm H H1 L S (4000) 0.40(0.29) 1.80(1.32) 2.(1.55) Sealing Materials Seat Stem End Packing Seal FKM FKM 344(00) 0.40(0.29) 1.90(1.40) 2.20(1.62) Pressure ,000psig(275bar) 6,000psig(413bar) 3,000psig(206bar) 4,000psig(275bar) 413(6000) 0.45(0.33) 2.00(1.47) 2.30(1.69) Temperature Rating -30 to 130 (-22 to to 180 (-22 to to 230 (-65 to to 1 (-9 to to 160 (-9 to to 2 (-31 to 4 The above pressure rating is for 2-way In-line pattern valves. 80% of the above rating shall be applicable to 2-way angle pattern valves and 3-way valves. The rated pressure shown above is the maximum allowable pressure to the seat. If the system requires higher pressure to test, the valve must be in open position before and during test so as not to damage the seat. Pressure ratings of valves are sometimes limited to the maximum working pressure of pipe ends and tubing connected. The working pressure of tubing must be considered in the calculation of total system working pressure. SIDE PORT INLET 1/4 turn handle For flow switching Outlet d L Inlet d Outlet H1 S BOTTOM PORT INLET 1/2 turn handle For flow switching and isolation H H1 Outlet d Isolation d L Inlet d Outlet 23

11 Panel Mounting Locking nut panel mounting Ordering designator : PN Screw hole panel mounting Ordering designator : PS Locking Nut T Panel L t L1 PN-Panel Mount Information Valve Series SBV1H SBV2H SBV3H Panel Hole Dril 30.0(1.18) 38.0(1.) 38.0(1.) Unit:mm(inch) Panel Thickness Max. 4.0(1.157) Max. 4.0(1.157) Max. 4.0(1.157) PS-Panel Mount Information Valve Series SBV1H SBV2H SBV3H L L1 t T 34.0(1.33) 36.0(1.42) 40.0(1.57) 26.0(1.02) 29.0(1.14) 35.0(1.37) 4.0(0.15) 5.0(0.20) 6.0(0.23) Unit:mm(inch) 30.0(1.18) 38.0(1.) 38.0(1.) Sour Gas Service Is provided to meet NCE Standard MR Testing Every valve is factory tested for bubble-tight leakage at both seat and stem packing with nitrogen at 00psi(69bar). Hydraulic shell test is performed at 1.5 times the working pressure. Seats have a maximum allowable leak rate of 0.1sccm. Optional tests are available upon request. Ordering Information Selection the applicable options from designators listed below. SBV1H S 4T PC PN LD OH SG S6 Series by Orifice Size End Connection Inlet-Outlet Size Seat Material Panel Mounting Locking Device Handle Nil : Standard PVDF PN : Lock nut panel LD :#Locking Device Nil :#Standard lever PC : PCTFE mounting handle PK : PEEK PS : Screw hole panel OH: Oval Handle mounting (pplicable only for SBV1H) Sour Gas Body Material Nil :#Without(Standard) S6 :#316 Stainless Steel SG: Sour Gas Service MO: lloy400 SFETY in VLVE SELECTION When selecting a valve, the total system design must be considered to ensure safe, trouble-free performance. Valve function, materials compatibility, adequate ratings, proper installation, operation, and maintenance are the responsibility of the system designer and user. 24

12 SFBV60Series Forged High pressure Ball Valves Features Pressure rating up to 6,000psig Temperature rating from to 3177with Standard PCTFE seat. Free floating ball design provides seat wear compensation, therefore ensures leak proof shut-off at high pressure. High flow in a compact design. Panel mountable as standard. Blow out proof design with internally loaded stem. Micro-finished ball provides a positive seal. Low operating torques and positive handle stops. Handle indicates flow direction. Straight through flow path for minimum pressure drop. Bi-Directional flow. Chevron packing standard for positive leak tight. 90 degree actuation. Every valve is 0% factory tested with the (69bar). Variety of end connections include reliable S-LOK tube fittings, Male/Female NPT&ISO/BSP threads. pplications Water Oil Gas Petrochemical Testing Every valve is factory tested for bubble-tight leakage at both seat and stem packing with nitrogen at 00psi(69bar). Seats have a maximum allowable leak rate of 0.1sccm. Optional tests are available upon request. Materials of Construction Item Description Body End Connector Ball Seats Retainer Retainer Seal End Seals Stem Stem Packing Stem Washer Packing Bolt Lock Nut Set Screw Handle Grade/STM Specification S316/276, 479 S316/276, 479 S316/276, 479 PCTFE, optional, PEEK S316/276, 479 S316/276, 479 S316 S316/276, 479 S316/276, 479 Stainless Steel Black Nylon standard Molybdenum disulfide with hydrocarboncoating. Note : wetted parts are listed in orange color. Lubricant is Fluorocarbon based. 25

13 2-Way (Shut-Off Valve) In-line pattern F(B:80, C:00) C d-panel hole drill T-max panel thickness E H D Ordering Information and Dimensions Basic Ordering Number End Connections Orifice Inlet Outlet mm(in.) S-1T 1/16S-LOK 1.3(0.052) (1.30) S-2T 1/8 S-LOK 2.4(0.093) (1.36) F-2N 1/8Female NPT 27.2(1.07) SFBV1 M-2N 1/8Male NPT 29.9(1.18) 4.2(0.165) /4 S-LOK 37.6(1.48) M-4N 1/4Male 34.3(1.35) S-3M 3mm S-LOK 2.2(0.086) (1.37) S-2T 1/8 S-LOK 2.4(0.093) (1.65) 1/4 S-LOK MS-4N4T 1/4Male NPT 1/4S-LOK 4.8(0.189) 1.04 (1.74) FS-4N6T 1/4Female NPT 1/4S-LOK F-4N 1/4Female NPT 38.4(1.51) M-4N 1/4Male NPT 41.1(1.62) SFBV2 MF-4N 1/4Male NPT 1/4Female NPT 38.4(1.51) 41.1(1.62) 11.9 MS-4N6T 1/4Male NPT 3/8S-LOK 6.4(0.2) 2.34 (0.47) FS-4F6T 1/4Female NPT 3/8S-LOK 45.7(1.80) 38.4(1.51) S-6T 3/8S-LOK 45.7(1.80) M-6N 3/8Male NPT 41.1(1.62) 41.1(1.62) S-6M 6mm S-LOK 4.8(0.189) (1.75) 44.5(1.75) S-8M 8mm S-LOK 45.2(1.78) 45.2(1.78) 6.4(0.2) 2.34 S-M mms-lok 46.0(1.81) 46.0(1.81) F-6N 3/8Female NPT 49.5(1.95) 49.5(1.95) 1/2Female NPT 54.6(2.15) 54.6(2.15) S-8T 1/2 S-LOK.3(0.406) (2.34) 59.4(2.34) 17.8 SFBV3 M-8N 1/2Male NPT 56.4(2.22) 56.4(2.22) (0.70) 3/4 S-LOK S-12M 12mmS-LOK 9.5(0.375) (2.33) 59.2(2.33) S-16M 16mmS-LOK.3(0.406) 6.42 Dimensions are for reference only and are subjet to change. Dimensions with S-LOK nuts are in finger-tight posion. Flow Rate Pressure Drop to tomosphere(p) in psi ir SCFM Water US GPM Flow rate calculated with 00psig(69bar)inlet pressure. To determine m 2 /hr multiply GPM by and SCFM by B Dimensions B D E H C F d T 33.0(1.30) 34.5(1.36) 27.2(1.07) 29.9(1.18) (1.48) (0.33) (0.39) (0.91) (0.71) (1.85) (0.64) 34.3(1.35) 34.8(1.37) 41.9(1.65) (1.74) 41.1(1.62) 38.4(1.51) 38.4(1.51) (0.42) 17.5 (0.69) 38.9 (1.53) (1.74) mm(inch) 30 (1.00) 38.1 (1.) 78 (3.07) 99 (3.9) (0.77) 22.9 (0.90) 3.3 (0.13) 6.4 (0.25) 9.7 (0.38)

14 3-Way (Switching Valve) C F 3-way ball valve SFBV 3-way Ball Valve is designed to switch media through the bottom port and direct it to out of two outlet ports. d-panel hole drill T-max panel thickness H E D Ordering Information and Dimensions Basic Ordering Number SFBV1-3B SFBV2-3B SFBV3-3B S-1T S-2T F-2N M-2N M-4N S-3M S-2T F-4N M-4N S-6T M-6N S-6M S-8M S-M F-6N S-8T M-8N S-12M S-16M End Connections Inlet Outlet 1/16 S-LOK 1/8 S-LOK 1/8 Female NPT 1/8 Male NPT 1/4 S-LOK 1/4 Male 3mm S-LOK 1/8 S-LOK 1/4 S-LOK 1/4 Female NPT 1/4 Male NPT 3/8 S-LOK 3/8 Male NPT 6mm S-LOK 8mm S-LOK mm S-LOK 3/8 Female NPT 1/2 Female NPT 1/2 S-LOK 1/2 Male NPT 3/4 S-LOK 12mm S-LOK 16mm S-LOK Orifice mm(in.) 1.3(0.052) 2.4(0.093) 4.2(0.165) 2.2(0.086) 2.4(0.093) 4.8(0.189) 5.0(0.196) 5.0(0.196) 4.8(0.189) 5.0(0.196).3(0.406) Dimensions mm(inch) B E D H C F d T 33.0(1.30) 34.5(1.36) 27.2(1.07) 29.9(1.18) 37.6(1.48) 34.3(1.35) 34.8(1.37) 41.9(1.65) (1.74) 38.4(1.51) 41.1(1.62) 45.7(1.80) 41.1(1.62) 44.5(1.75) 45.2(1.78) 46.0(1.81) 49.5(1.95) 54.6(2.15) 59.4(2.34) 56.4(2.22) 33.7(1.30) 36.4(1.36) 29.9(1.18) 29.9(1.18) 37.2(1.46) 29.9(1.18) 36.4(1.36) 45.5(1.79) 47.8(1.88) 41.9(1.65) 44.7(1.76) 49.3(1.94) 44.7(1.76) 47.8(1.88) 48.5(1.91) 49.5(1.95) 58.2(2.29) 63.2(2.49) 68.1(2.68) 65.8(2.59) 68.1(2.68) 67.8(2.67) 65.5(2.67) 9.5(0.375).3(0.406) (2.33) 56.9(2.33) Dimensions are for reference only and are subjet to change. Dimensions with S-LOK nuts are in finger-tight posion. B 8.5 (0.33) 11.9 (0.47) 17.8 (0.70) 23.2 (0.91) 38.9 (1.53) (1.74) 18.0 (0.71) 30 (1.18) 38.1 (1.) 47.0 (1.85) 78 (3.07) 99 (3.9) 16.3 (0.64) 19.6 (0.77) 22.9 (0.90) 3.3 (0.13) 6.4 (0.25) 9.7 (0.38) Flow Rate Pressure Drop to tomosphere(p)in psi ir Water US Flow rate calculated with 00psig(69bar)inlet pressure. To determine m2 /hr multiply GPM by and SCFM by

15 Technical Data-Pressure and Temperature Rating Seat Materials Pressure Temperature Rating Pressure Temperature PCTFE 6,000psig(413bar) -54 to 177 (-65 to 3) PEEK 6,000psig(413bar) -54 to 232 (-65 to 4) 1,0psig(3bar) -54 to 177 (-65 to 3) Caution Pressure Rating with 3-way side ports of as inlet : 1psig(bar) Ordering Information Selection the applicable options from designators listed below. SFBV1 S 4T PC SG S6 Series by Orifice Size End Connection Inlet-Outlet Size Seat Material Nil :#Standard PCTFE PK : PEEK TE : Sour Gas Nil :#Without(Standard) SG:#Sour Gas Body Material S6 :#316 Stainless Steel SFETY in VLVE SELECTION When selecting a valve, the total system design must be considered to ensure safe, troble-free performance. Valve function, materials compatibility, adequate ratings, proper installation, operation, and maintenance are the responsibility of the system designer and user. 28