Daily Drilling Summary Report

Transcription

1 Date: 12/22/16 Rig: Norton Rig #2 Daily Cost: $32,507 Report #: 3 Current Depth: Progress Last 24 Hrs: 1628 Cum Cost: $268,248 Norton Rig #2 finished PU BHA, tested motor, filled conductor. Spudded well 8:15 AM & drilled from 77' to 478' Executive 54 ft/hr). Ran deviation 443' =.75, TD 478'. Continued drilling from 478' to ft/hr). Tour change & Summary: continued drilling from 658' to 1,705' ft/hr). TD 17-1/2" Surface 7:05 AM 12/22/16 at a depth of 1,705. Drilling 1,699', ROP = 62.5 ft/hr, WOB = 18.3 klbs. 1,705'. : 8:00 AM Finish PU BHA, test motor, fill conductor. 3:30 PM Drill from 77' to 478' 54 ft/hr). 4:00 PM Deviation 443' = 0.75, TD 478'. 7:00 PM Drill from 478' to 658' 60 ft/hr). Drill from 658' to 1,705' ft/hr ). TD 17-1/2" 7:05 AM 12/22/16. Rig Up/Down TRC Depth Angle Bit Size Mfg. Type Serial # Jets 8x20 Ulterra 1705' 77' RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr No. 1 Spudded well 8:15 AM 12/21/16. TD 17-1/2 hole 1,705 : 12/22/16, 7:05 AM rotating 75 ft/hr. Diesel (gal) Start Received End

2 Date: 12/23/2016 Rig: Norton Rig #2 Daily Cost: $104,634 Report #: 4 Current Depth: 1705' Progress Last 24 Hrs: 0 Cum Cost: $372,882 Circulate clean up 1,705', TOOH to BHA 50K drag at 1,520' & 1,055', TIH to btm & CBU spot high vis pill. TOOH tight 1,615', 1,603', 1,598', 1,247', RU laydown machine & LD BHA, RU csg tools & run 39 jts , 68#/ft, J-55 csg to 1,705', Executive CBU & pump cmt, 1,106 sx 12.5 ppg (415 bbls) 379 sx 14.8 ppg (90 bbls) displace w/ 242 bbls, bump plug w/ 900 Summary: 2:40 AM 12/23/16, check floats, floats holding, full returns. 510 sx (192 bbls ) cmt to surface. Test csg to 1,500 psi. WOC. : 8:30 AM 10:00 AM 11:30 AM 2:30 PM 3:30 PM 7:00 PM 10:00PM 11:30PM 12:00PM 3:00AM 3:30AM 7:00AM WOC. Pump sweeps & circulate bottoms up 2X. TOOH to DCs for wiper run. Jts (3nd & 7th stand) pulled tight off bottom. TBIH to bottom. Pump sweeps & circulate bottoms up 2X, spot high vis pill. TOOH, tight 1,615', 1,603', 1,598', 1,247'& 716'. Pulled up to 166 klbs over. RU LD machine & LD BHA. RU Casing Crew, HSM. Start RIH w/ 13-3/8", 68#, J-55, BTC csg. Finish running , 68 #/ft J-55 csg to 1,705', wash down last 2 jts. 430 GPM. PJSM w/ Baker, & RU to cmt. Test lines & pump cmt, 415 bbls lead 12.5ppg, 90 bbls 14.8 ppg, had full returns on job. 192 bbls cmt back to surface. Bump plug at calculated displacement 242 bbls. Test csg to 1,500 psi, Charted for 30 minutes. WOC, clean active pits. Suction Depth Angle Bit Size Mfg. Type Serial # Jets 443' ' 1705' 17-1/4 Ulterra U616S PDC x20 2 RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr Casing Detail: 39 jts 13-3/8, 68 #, J-55, BTC new API Csg Float 1, KB Float 1, KB Cement Detail: Lead: 1,106 sx; 35/65 POZ "Premium Plus C" pps Static Free + 5% Salt + 1/4 pps celloflakes + 4% Bentonite + 2% Sodium Matasilicate + 5% MPA gps FP-6L, 12.5 ppg, 2.14 cuft/sx, gals/sx, 2, cuft Tail: 379 sx; Premium Plus C pps Static Free + 1% CaCl pps FP-6L, 14.8 ppg, 1.34 cuft/sx, 6.34 gals/sx, cuft. Bumped plug w/ 900 2:40 AM 12/23/16. Floats held, circulated 510 sx (192 bbls) cement to surface. Tested 13-3/8 csg to 1,500 psi for 30 mins, received good chart.

3 Date: 12/24/2016 Rig: Norton Rig #2 Daily Cost: $65,370 Report #: 5 Current Depth: 1853' Progress Last 24 Hrs: 148 Cum Cost: $438,252 Install 13-5/8" 3M x 13-3/8" SOW csg head, test to 900 psi. NU & test BOP, run Gyro Survey. PU & test BHA, TIH & tag Executive 1,604', displace well w/ 10.0 ppg brine, drill cmt & float equip. 1,614', 1,705'. Drill new formation from 1,705' to Summary: 1,853'. : 8:30 AM 11:00 AM 5:30 PM 7:00 PM 11:00PM 1:00AM 2:00AM 3:30AM 7:00AM Drilling 12.25" hole 1,853'. Cut & drain conductor, cut 13 3/8 csg. Dress 13-3/8" csg & install 13-5/8" 3M x 13-3/8" SOW csg head, test to 900 psi. Stack BOP & NU, run Gyro while NU. Function test BOP, test BOP to 250 psi/1,500 psi Low/High test. SLM BHA, M/U & surface test BHA & MWD. TIH, tag 1,605'. Displace hole w/ 10.0 ppg brine, re-route discharge lines to outside reserve. Drill cmt & float equip, 1,614', 1,705'. Drill new formation from 1,705' to 1,853' ft/hr). Suction Depth Angle Bit Size Mfg. Type Serial # Jets ' 1705' 17-1/4 Ulterra U616S PDC x ' 12-1/5 U7195 PDC x18 + 3x RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr

4 Date: 12/25/2016 Rig: Norton Rig #2 Daily Cost: $30,359 Report #: 6 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $468,610 Executive Drill from 1,853' to 2,223' 85.5 ft/hr). MWD tool failure, trouble shoot MWD. TOOH, replace MWD & surface test, TIH. Summary: Drill from 2,223' to 3,105' ft/hr). Had 10.5 hrs NPT (MWD). : 12:30 PM 1:00 PM 4:00 PM 7:00 PM 8:00 PM 11:00PM 7:00AM Drilling 12.25" hole 3,105'. Drill from 1,853' to 2,223' 67.3 ft/hr). Lost communications w/ MWD tool, trouble shoot tool. TOOH to MWD tool. MWD tool on surface, change out faulty parts & reprogram. Finish changing out MWD & surface test. TIH. Drill from 2,223' to 3,105' ft/hr ) TRC 11.8 Depth Angle Bit Size Mfg. Type Serial # Jets / ' U616S PDC x /5 1400' 1705' U7195 PDC x18 + 3x22 15/25K RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr ' Ulterra

5 Date: 12/26/2016 Rig: Norton Rig #2 Daily Cost: $26,839 Report #: 7 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $495,449 Executive Drilling 12.25" hole section from 3,105' to 3,544'. Service rig & Topdrive, continue drilling from 3,544' to 4,640' Summary: ft/hr ). Drilling 12.25" hole 4,640'. : 1:30 PM Drill from 3,105' to 3,544' ft/hr). 2:00 PM Service rig & Topdrive. 7:00 PM Drill from 3,544' to 3,826' ft/hr). 7:00AM Drill from 3,826' to 4,640' ft/hr) TRC 11.8 Depth Angle Bit Size Mfg. Type Serial # Jets / ' U616S PDC x / ' U7195 PDC x18 + 3x22 15/25K RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr ' Ulterra

6 Date: 12/27/2016 Rig: Norton Rig #2 Daily Cost: $28,860 Report #: 8 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $524,310 Continued drilling & sliding from 4,640' to 6,363'. Total footage = 76.4 ft/hr. Slide from 4,671' to 4,691', 4773' to 4788' & from 5,517 to 5,532. Pump #1 5,273' (4:20 PM) - change out liners, ROPs down to ft/hr. Pump #1 back on 5,510' (8:20 PM), ROPs increased to ± 105 ft/hr. Executive Drilling 6,314', ROP = 92 ft/hr, WOB = 30 klbs, Rot = 69 rpm, Tor = kft-lb, Pump Rate = 733 gpm, Diff Press = Summary: psi, SPP = 3,594 psi. Connection & 6,362.8', after connection kicked pumps on & had no returns. LD makeup jt to TOOH 5 stands. Latched onto DP in the hole & found pipe was 6,358'. Worked to free pipe pulling 100 K. Regained full returns, pipe still 6,357', continued working to free pipe. : 12:30 PM 1:00 PM 7:00 PM 5:00 AM 5:30 AM 6:00 AM 6:30 AM Working stuck pipe w/ 6,359' (2 ft off bottom). Drill/ Slide from 4,640' to 4,954' 57 ft/hr, Slide from 4,671' to 4,691' & from 4,773' to 4,788'). Rig Service. Drill from 4,954' to 5,423' 78.2 ft/hr). Pump #1 5,273' (4:20 PM) - change out liners, ROPs down to ft/hr. 5,510' (8:20 PM). ROPs increased to ± 105 ft/hr. Drilling 6,314', ROP = 92 ft/hr, WOB = 30 klbs, Rot = 69 rpm, Tor = kft-lb, Pump Rate = 733 gpm, Diff Press = psi, SPP = 3,594 psi. Connection & 6,362.8', after connection kicked pumps on & had no returns. LD makeup jt to TOOH 5 stands. Latched onto DP in the hole & found pipe was 6,358'. Worked to free pipe pulling 100 K. Regained full returns, pipe still 6,357' TRC 11.8 Depth Angle Bit Size Mfg. Type Serial # Jets / ' U616S PDC x / ' U7195 PDC x18 + 3x22 15/25K RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr ' Ulterra Morning tour reported losing 3" of fluid in working pits while drilling from 5,430' to 6,170'. Increase fiber LCM in suction pits. Drilling 6,314', ROP = 92 ft/hr, WOB = 30 klbs, Rot = 69 rpm, Tor = kft-lb, Pump Rate = 733 gpm, Diff Press = psi, SPP = 3,594 psi. Connection & 6,362.8', after connection kicked pumps on & had no returns. LD makeup jt to TOOH 5 stands. Latched onto DP in the hole & found pipe was 6,358'. Worked to free pipe pulling 100 K. Regained full returns, pipe still 6,357', continued working to free pipe

7 Date: Rig: Norton Rig #2 Daily Cost: $44,150 Report #: 9 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $568,460 Continued working stuck pipe w/ 6,263' by pulling up to 283 klbs, applying torque & increasing pump rate. Spotted 80 bbls FW across BHA to lighten fluid in BHA. Worked to free pipe. Gained ± 6'. Make call for diesel delivery. Spotted 40 bbls of diesel across bottom of DS, stand-by for diesel to slick-up/ lighten bottom of BHA. Continued working pipe while pumping additional diesel 15 bbls at a time, letting fluid rest for 15 mins between pulling & applying torque. Gained ± 4'. Decision was made to call for N2. 90 bbls total diesel pumped. Kicked pumps on to displace diesel out of hole & lost returns. Pumped 38 bbls fluid before regaining returns. Returns carried blocks of sand/lcm out of hole. Executive Continued working pipe while standing by for Pro Petro N2. Pro Petro on location w/ 680,000 SCF of nitrogen, RU N2 pump, Summary: flowline from choke manifold to pit & "muffler" at end of flowline to restrict flow when N2 comes around. HSM. Pumped Nitrogen laden mud as follows: 40 bbls BW ramping N2 up to 300 SCF/bbl + 80 bbl 45 Vis mud ramping N2 up to 500 SCF/bbl + 30 bbls BW ramping N2 down to 300 SCF/bbl. WO N2 mud to clear, latched onto DP & worked to free pipe. Unable to gain any footage, pulling up to 280 klbs. Pumped 2nd stage of Nitrogen laden mud as follows: 50 bbls BW ramping N2 up to 500 SCF/bbl + 80 bbl 45 Vis mud ramping N2 up to 80,000 SCF/bbl + 90 bbls BW ramping N2 down to 500 SCF/bbl. Stand-by for N2 Mud to clear WB. Latched onto DP & found pipe was free. POOH standing DP back. : TOH to check tools/ reloading hole w/ BW. 8:00 AM 2:30 PM 3:00 PM 9:00 PM 11:00 PM 1:30 AM 2:00 AM 3:00 AM 3:30 AM 4:30 AM Pipe stuck w/ 6,263', continued working to free pipe, pulling up to 283 klbs, applying torque & increasing pump rate. Spotted 80 bbls FW across BHA to lighten fluid in BHA. Worked to free pipe. Gained ± 6'. Make call for diesel delivery. Spotted 40 bbls of diesel across bottom of DS, stand-by for diesel to slick-up/ lighten bottom of BHA. Continued working pipe while pumping additional diesel 15 bbls at a time, letting fluid rest for 15 mins between pulling & applying torque. Gained ± 4'. Decision was made to call for N2. Kicked pumps on to displace diesel out of hole & lost returns. Pumped 38 bbls fluid before regaining returns. Returns carried blocks of sand/lcm out of hole. Continued working pipe while standing by for Pro Petro N2. Pro Petro on location w/ 680,000 SCF of nitrogen, RU N2 pump, flowline from choke manifold to pit & "muffler" at end of flowline to restrict flow when N2 comes around. HSM. Pumped Nitrogen laden mud as follows: 40 bbls BW ramping N2 up to 300 SCF/bbl + 80 bbl 45 Vis mud ramping N2 up to 500 SCF/bbl + 30 bbls BW ramping N2 down to 300 SCF/bbl. WO N2 mud to clear, latched onto DP & worked to free pipe. Unable to gain any footage, pulling up to 280 klbs. Pumped 2nd stage of Nitrogen laden mud as follows: 50 bbls BW ramping N2 up to 500 SCF/bbl + 80 bbl 45 Vis mud ramping N2 up to 80,000 SCF/bbl + 90 bbls BW ramping N2 down to 500 SCF/bbl. Stand-by for N2 Mud to clear WB. Latched onto DP & found pipe was free. POOH standing DP back. Rig Up/Down Drilling Reaming Coring Plug Back Plug Back TRC.1/.35 0/87.2 Depth Angle Bit Size Mfg. Type Serial # Jets 77' Ulterra 1705' Diesel (gal) RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr 1 Start PZ11 No Received 23 hrs down time to free pipe. Does not include TOOH & TIN to check tools. NA End 10 Used 4185 Rate ($/gal) Total Cost ($)

8 Date: 12/29/2016 Rig: Norton Rig #2 Daily Cost: $49,663 Report #: 10 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $618,123 Continued TOOH standing back, keeping DP & annulus full. Began pump & break 382 gpm, getting full returns. LD bit #2, found bit w/ 11 teeth chipped or missing, motor shock sub & MWD tool all visually appear to be in good condition. PU directional BHA #2, surface test motor & MWD. TIH w/ BHA #2 + DCs + DP to 1,700'. Slip & cut drlg line, 80', service rig. Executive Condition mud in working pits & TIH to 3,000'. Crew mixed LCM pill in slug tank in case of lost circulation. Circulated bottoms Summary: 3,000' w/ BW. Nova Mud Engineer on location. Continued TIH to 5,300'. Installed rotating head w/ new rubber. Break circulation after pumping 50 bbls BW & continued circulating getting full returns. Mix & condition mud to ± 34 vis & 7 water loss. (Note: Crew is shorthanded.) Began washing down from 5,300' to 150 ft/hr, pump 410 gpm. Good returns w/ minimal fluid loss. : 8:00 AM 10:30AM 1:00PM 3:00PM 6:00 PM 8:00 PM 9:00 PM 10:30 PM 3:00 AM Washing down w/ BHA #2 to 6,000'. Fill pipe & backside, break circulation & 382 gpm, full returns. POOH & LD bit #2. LD directional BHA #1 & PU directional BHA #2, surface test motor & MWD. TIH w/ DC + DP to 1,700'. Slip & cut drlg line, 80'. Condition mud in working pits. TIH to 3,000', mix LCM pill in slug tank. Circulate bottoms 3,000' w/ BW. Nova Mud Engineer on location. TIH to 5,300'. Install rotating head w/ new rubber. Break circulation after pumping 50 bbls BW circulate. Mix & condition mud to ± 34 vis & 7 water loss. (Note: Crew is short handed.) Wash down from 5,300' to 150 ft/hr, pump 410 gpm. Good returns w/ minimal fluid loss. Rig Up/Down Drilling Reaming Coring Plug Back Plug Back Depth Angle Bit Size Mfg. Type Serial # Jets 1705' Ulterra Ulterra Diesel (gal) RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr 1 Start PZ11 No Received NA End 10 Used 4185 Rate ($/gal) Total Cost ($)

9 Date: 12/30/2016 Rig: Norton Rig #2 Daily Cost: $35,955 Report #: 11 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $654,078 Washed & reamed from 5,800' to 6,019'. Circulated bottoms up & had no fluid loss, mud check 33 Vis, 7 water loss, 10.1 Executive ppg. Continued washing & reaming from 6,019' to 6,361' (point at which pipe was stuck). Circulated bottoms up & reconditioned mud 38 Vis, 8 water loss, 10.0 ppg- did not lose any fluid. Drilled 12.25" hole section from 6,361' to Summary: 7,113', slid from 6,738' to 6,757', & 7,020 to 7,046'. TD 12-1/4 4:30 AM, 12/30/16. : 8:00 AM 9:00 AM 12:00 PM 12:30 PM 5:00 PM 5:30 PM 6:30 PM 7:00 PM 8:30 PM 3:30 AM 4:30 AM TD'd 12-1/4" hole, circulating bottoms up 2 times. Wash & ream from 5,800' to 6,019'. Circulate, no mud loss. Wash & ream from 6,019' to 6,361'. Circulate & condition mud, no mud loss. Drill 12.25" hole section from 6,361' to 6,644' ft/hr). Service Rig & TDS. Drill 12.25" hole section from 6,644' to 6,707' 63 ft/hr). SPM, unplug dump lines on shale shakers. Drill from 6,707' to 6,738' 20.7 ft/hr). Slide from 6,738' to 6,757' (19'). Drill from 6,757' to 7,020' 39 ft/hr). Slide from 7,020' to 7,046' (26'). Drill from 7,046' to 7,113' 67 ft/hr). Circulate bottoms up times 2. Rig Up/Down Drilling Reaming Coring Plug Back Plug Back /.4 0/87.9 Depth Angle Bit Size Mfg. Type Serial # Jets 1705' Ulterra Ulterra Diesel (gal) RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr 150 Start PZ11 No Received TD 12-1/4" 4:30 AM, 12/30/16. End 951 Used 4185 Rate ($/gal) Total Cost ($)

10 Date: 12/31/2016 Rig: Norton Rig #2 Daily Cost: $201,239 Report #: 12 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $855,317 Finished circulating bottoms up times 2- returns are clear. TOOH for wiper run from 7,113' to 5,250', max 6,300', 20K over. TBIH to 7,113'- had minimal fill. Circulated 1st high Vis sweep, circulated 2nd calculated bottoms up strokes & lost full returns. TOOH from 7,113' to BHA- no drag. Filled backside w/ 140 bbls fresh water- hole stayed full. RU laydown Executive machine & LD BHA. Changed out rig bails & elevators, prepare floor to run csg. Weatherford DV Tool Operator on location. Summary: RU csg tools & HSM. RIH w/ 9-5/8", 40# Csg as follows (bottom to top): FS + SJ + FC + 69 jts HCL-80 + DV Tool + 89 jts J-55. 7,109.85', 7,065.82', DV 3,956.58'. Had no problems getting to bottom. RD csg crew & PU/LD machine. Circulated csg w/ rig pumps- getting full returns. : 7:30 AM 8:30AM 9:30AM 12:30PM 6:00PM 6:30 PM 8:00PM 9:00PM 10:00 PM 5:30 AM RU Baker Hughes Cementers. Finish circulate bottoms up times 2- hole clean. TOOH from 7,113' to 5,250', max 6,300', 20K over. TIH to 7,113'. Circulate 1st sweep, circulate 2nd calculated btm. Up stks lost full returns. TOOH from 7,113' to BHA'- no drag. Fill backside w/ 140 bbls fresh water- hole staying full. RU laydown machine. LD BHA. Change rig bails & elevators. RU csg tools. HSM. RIH w/ 9-5/8", 40# Csg as follows (bottom to top): FS + SJ + FC + 69 jts HCL-80 + DV Tool + 89 jts J-55. 7,109.85', 7,065.82', DV 3,956.58'. No problems getting to bottom. RD csg crew & PU/LD machine. Circulate csg- getting full returns. Rig Up/Down Drilling Reaming Coring Cond mud/circ Trips Plug Back Sqz Cmt Fishing Plug Back Sqz Cmt Fishing / Depth Angle Bit Size Mfg. Type Serial # Jets Diesel (gal) Ulterra 1800 No. 1 PZ Start Ulterra 1800 No. 2 PZ11 Received RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr End Used Casing Detail: 7, Top of 7, jts 9-5/8, 40#, HCL-80, LTC Csg. Top of DV 3, jts 9-5/8, 40#, J-55, LTC Csg to surface Rate ($/gal) Total Cost ($)

11 Date: 1/1/2017 Rig: Norton Rig #2 Daily Cost: $89,846 Report #: 13 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $945,163 Circulated csg w/ rig pump- full returns. Well flowed 20 min then Static. Continued circulating w/ full returns. RU pump trucks & held PJSM. Stand-by for booster pump from Baker Hughes. Test lines, mixed & pumped Stage 1 cmt as follows: Lead 917 sx 50/50 POZ Premium Plus C + additives, Tail 254 sx 50/50 POZ Premium Plus C + additives. Dropped bottom 1:51 PM, start displacement w/ 30 bbl FW lead followed by BW Mud. With 220 bbls displacement gone lost full returns, regained partial returns from 300 to 410 bbls gone, then lost full returns until plug down w/ 1,100 3:15 PM. Float Executive holding, dropped DV Tool opening cone. Pressured up on opening cone w/ 670 psi & opened DV Tool. Pumped 20 bbls & Summary: regained full returns. Changed lines to rig pump & circulated w/ rig pump getting full returns. Did not circulate any cement off top of DV Tool. WOC for 4 hours while circulating w/ rig pump. HSM, mixed & pumped Stage 2 cement as follows: Lead 552 sx 50/50 POZ C + additives, Tail 145 sx 50/50 POZ + additives. Bumped plug w/ 1,950 10:21 PM. Held pressure for 30 mins (csg test). Bleed pressure back to pump, DV Tool closed. No cement to surface. RD Baker Hughes Cementers. ND & hung back BOP stack. Set slips w/ 200K setting down on them. ND spacer spools, cut csg, NU & tested B Section WH to 1,500 psi. Began NU BOP. NU BOP, jetting pits. : 8:00 AM Circulate w/ rig pump- full returns. Well flowed 20 min then Static. 11:30 AM Circulate w/ full returns. RU pump trucks & held PJSM. WO Baker equipment. 4:00PM 8:00PM 10:30 PM 11:00 AM 11:30 PM 12:30 AM 5:00 AM Test lines to 3m PSI, pump cmt. 1 stage as per Baker cement proposal. Drop 220 bbls displacement gone lost full returns, regain partial returns from 300 to 410 bbls gone & lost full returns until bumping plug. Float holding, drop bomb (25 min) & pressure up & open DV 625 psi. Pump 20 bbls & regain full returns. Change lines to rig pump. Circulate w/ rig pump- full returns. HSM. Mixed & pumped Stage 2 cement: Lead 552 sx 50/50 POZ C, Tail 145 sx 50/50 POZ. Bumped plug w/ 1,950 10:21 PM. Held pressure for 30 mins (csg test). Bleed pressure back to pump, DV Tool closed. RD Baker Hughes Cementers. ND & hang back BOP Stack. Set slips w/ 200K setting down on them. ND spacer spools, cut csg, NU & tested B Section WH to 1,500 psi. NU BOP. Rig Up/Down Plug Back Drilling Sqz Cmt Reaming Fishing Coring Plug Back Cond mud/circ Sqz Cmt Trips Fishing TRC 0/ Depth Angle Bit Size Mfg. Type Serial # Jets Diesel (gal) Ulterra 1800 No. 1 PZ Start Ulterra 1800 No. 2 PZ11 Received RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr End Used Cement Details: Stage 1: Lead: 917 sx 50/50 POZ Premium Plus C + 3 pps LCM % Bentonite +.2% Sodium Metasilicate +.5% FL-52D gps FP-6L + 5% Salt pps Static Free +.5% R ppg, 2.46 cuft/sx, cuft. Tail: 254 sx 50/50 POZ Premium Plus C +.4% CD % Bentonite +.35% Sodium Metasilicate +.1% FL- 52D gps FP-6L pps Static Free + 5% Salt +.2% R ppg, 1.30 cuft/sx, cuft. Displaced w/ 40 bbls FW followed by 496 bbls BW Mud. Stage 2: Lead: 552 sx 50/50 POZ Premium Plus C +.5% FL-52D gps FP-6L pps Static Free + 5% Salt + 3 pps LCM % Bentonite +.2% Sodium Metasilicate ppg, 2.46 cuft/sx, cuft. Tail: 145 sx 50/50 POZ Premium Plus C +.4% CD % Bentonite +.35% Sodium Metasilicate +.1% FL- 52D gps FP-6L pps Static Free + 5% Salt ppg, 1.30 cuft/sx, cuft. Displaced w/ 20 bbls FW followed by 284 bbls BW Mud Rate ($/gal) Total Cost ($)

12 Date: 1/2/2017 Rig: Norton Rig #2 Daily Cost: $53,457 Report #: 14 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $998,620 Finished NU BOP. Jet & clean active mud pits. RD dump lines & clean back yard. Spot Q max solids control equipment w/ rig forklift & began RU. Function tested BOP, pressure test BOP to 250 psi/1,500 psi Low/High test. Finished RU panic line to Executive reserve pit. PU & MU directional BHA as follows: 8-3/4" U613M PDC Bit + 6-3/4, 7/ w/ 8-1/2 NBS Motor + Summary: NM Nortrack Stab w/ 8-1/2" Blades + NM X/O + NMDC w/ MWD + NM X/O + Nortrack Stab w/ 8-1/2" Blades + (18) 6-1/2 DCs. Surface test MWN Tools. TIH to 3,101' & RU transfer pump to drill out DV Tool w/ BW. TIH & tagged & drilled out DV 3,997'. TIH to 6,914', closed rams on BOP & tested csg to 1,500 psi for 30 mins. Changed out swivel wash pipe. : 8:00 AM 9:00AM 1:30PM 4:00PM 6:00PM 7:00 PM 9:30 PM 12:00 AM 1:00 AM 2:00 AM 3:15 AM 4:45 AM 6:00 AM Continue RU solids control, changing out swivel wash pipe. Finish NU BOP. Finish cleaning active mud pits, RD dump lines & clean back yard. Spot Q max solids control equipment w/ rig forklift. Function test BOP, pressure test BOP to 250 psi/1,500 psi Low/High test. Finish RU panic line to reserve pit. PU & MU directional BHA. PU directional tools/scribe & test. TIH to 3,101'. RU transfer pump to drill out DV Tool w/ BW. TIH & tag DV 3,997'. Drill out DV Tool. TIH to 6,914'. Test csg to 1,500 psi for 30 mins. Change out swivel wash pipe. Rig Up/Down Drilling Reaming Coring Plug Back Plug Back TRC.1/.2 0/87.2 Depth Angle Bit Size Mfg. Type Serial # Jets Ulterra Ulterra Diesel (gal) RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr 150 Start PZ11 No Received Tagged & drilled out DV 3997'. Test csg from 6,914 to surface to 1,500 psi. Held pressure for 30 mins, received good chart. End 951 Used 4185 Rate ($/gal) Total Cost ($)

13 Date: 1/3/2017 Rig: Norton Rig #2 Daily Cost: $32,360 Report #: 15 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $1,030,980 Crew worked to prepare to transfer OBM to active pits, pumping out rain water & checking valves. Nova Mud Engineer on Executive location. Held PJSM, transferred & rolled 10.5ppg OBM to active pits. Displaced hole w/ 10.5 ppg OBM. Drilled 7,065' Summary: & drilled out cement to 7,110'. Continued drilling/sliding new hole from 7,110 to 7,867 = ft/hr. Slid for a total of 2.5 hrs & made 53. : 11:30 AM 12:30 PM 1:30 PM 5:30 PM 6:00 PM 7:00 PM 7:30 PM 11:00 PM 11:30 PM 1:30 AM 2:00 AM 3:00 AM 3:30 AM 4:00 AM 6:00 AM 6:30 AM Drilling 7,853 ', ROP = 80 ft/hr, WOB = 25 klbs, Rot = 51 rpms, Pump rate = 460 gpm, Diff Pres = 216 psi ppg, Vis = 55. Pump out rain water from active pits, PJSM & transfer 10.5 ppg OBM to active pits. Displace hole w/ 10.5 ppg OBM. Drill 7,065', drill cmt, 7,110'. Drill 8.75 hole section from 7,110' to 7,289' ft/hr). Service rig & TDS. Drill 8.75 hole section from 7,289' to 7,321' 32ft/hr). Slide from 7384' to 7394' (10 20 ft/hr). Drill from 7394' to 7571' ( ft/hr). Slide from 7571' to 7586' 30 ft/hr). Drill from 7586' to 7681' 47.5 ft/hr). Slide from 7681' to ft/hr). Drill from 7691' to 7759' 68 ft/hr). Rig Repair - Change out Grabber Dies. Slide from 7759' to 7767' 16 ft/hr). Drill from 7767' to 7850' 41.5 ft/hr). Slide from 7850' to 7860' 20 ft/hr). Drill from 7860' to 7867' 14' ft/hr). Drill from 7860' to 7867' 14' ft/hr) / Depth Angle Bit Size Mfg. Type Serial # Jets x 22 Ulterra 15/35K 80TD/126DH x18 + 3x22 Ulterra 15/25K 80TD/126DH RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr No. 1 PZ11 Diesel (gal) 85 Start 0 Received

14 Date: 1/4/2017 Rig: Norton Rig #2 Daily Cost: Report #: 16 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: Drilled 8-3/4" hole section from 7,854' to 8,100' 35 ft/hr). Lost returns, and POH from 8,100' to 7,724'. Mixed and condition LCM 20 #/bbl. Pumped LCM pill, plugged bit at calculated strokes to bit. POH to csg shoe and attempt to Executive unplug bit with no success. TOH pulling wet string for pugged off bit/pipe. LD bit, found bit jets clear. Shoulders on bit worn. Summary: Worked to remove MWD out on Monel. LD mud motor, found motor plugged off w/ LCM. PU on new 6-3/4, 7/ w/8-1/2 NBS Motor + new MWD & RIH. Test motor & MWD tool. PU new 8-3/4" U613M PDC Bit & TIH w/ new BHA : 2:00 PM 3:00 PM 4:00 PM 5:00 PM 7:00 PM 12:30 AM 3:00 AM 4:30 AM 5:30 AM TIH w/ new bit + new motor + new MWD Drill 8.75" hole section from 7,854' to 8,100' ( 35 ft/hr ) Lost returns, and POH from 8,100' to 7,724' Mix and condition LCM 20 #/bbl Pump LCM pill, plugged bit at calculated strokes to bit. POH to csg shoe and attempt to unplug bit with no success. POH with wet string. TOH pulling wet string for pugged off bit/pipe LD bit, found bit jets clear. Worked to remove MWD out on Monel. LD mud motor, found motor plugged off w/ LCM PU on new 6-3/4, 7/ w/8-1/2 NBS Motor + new MWD & RIH Test motor & MWD tool. PU new 8-3/4" U613M PDC Bit & TIH w/ new BHA Rig Up/Down Drilling Reaming Coring Cond mud/circ Trips Lube Rig Plug Back Sqz Cmt Fishing Dir. Work Sqz Cmt Fishing Dir. Work 66/ Depth Angle Bit Size Mfg. Type Serial # Jets 122 Start Ulterra No. 1 PZ Received Ulterra No. 2 PZ11 0 End RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr 63 Used Rate ($/gal) Number Total Cost ($)

15 Date: 01/07/2017 Rig: Norton Rig #2 Daily Cost: $56,447 Report #: 19 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $1,190,710 Drilled 8.75" hole section from 9,446' to 9,771' 28.3 ft/hr). Mud Motor stalling, ROPs down to 18 ft/hr, WOB = 35 klbs, Rot = 63 rpms, Torque = 9.1 kft-lbs, Pump Rate = 454 gpm, Diff Pres = psi, SPP = 2973 psi. 9.8 ppg, Vis = Executive 50. Circulate & spot heavy pill on bottom. TOH to check mud motor & bit. ± 4400' (inside csg), air lines are beginning to Summary: freeze on rig. Blocks will not raise or lower. Work to thaw & inspect rig. Found drum valve behind console frozen. Continued TOH for motor/ bit. : 4:00 PM 4:30 PM 7:00 PM 8:00 PM 11:00 PM 3:00 AM TOH to check motor & bit Drill 8.75" hole section from 9,422' to 9,735' ( ft/hr ) Service rig and TDS Drill 8.75" hole section from 9,735' to 9,773' ( ft/hr ) = 2973 psi. 9.8 ppg, Vis = 50. Circulate & spot heavy pill on bottom. Mud Motor stalling, TOH to Check mud motor & bit. Found drum valve behind console frozen. Continue TOH for motor/ bit / Depth Angle Bit Size Mfg. Type Serial # Jets 6 x 22 Ulterra 15/35K 80TD/126DH x 22 Ulterra 15/35K 80TD/126DH RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr No. 1 PZ11 Diesel (gal) 16 Start 129 Received

16 Date: 01/08/2017 Rig: Norton Rig #2 Daily Cost: $55,383 Report #: 20 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $1,285,061 Laid down 8-3/4 bit #3. Found bit to be in gauge & 3 teeth damaged. Attempted to drain mud motor- motor did not drain. Executive Changed out & shallow tested directional tools. MWD tool failed- repair, replaced & retested tool. TIH w/ BHA & 1 stand Summary: DP, slipped & cut 115' drlg line. TIH to 7,100' filling pipe every 20 stds. Circulate & condition mud to 9.7 ppg In/out. TIH & washed down to bottom. Drilled from 9,771' to 10, ft/hr). Drilling 10,123 ', ROP = 31.7 ft/hr, WOB = 30.2 klbs, Rot = 49 rpms, Torque = 9.9 kft-lbs, Pump Rate = 425 gpm, : Diff Pres = 238 psi, SPP = 2,598 psi. 9.8 ppg, Vis = 50. 8:30 AM 10:00 AM 11:30 AM 1:00 PM 4:00 PM 5:00 PM 7:30 PM Break bit & drain mud motor- motor did not drain. Change directional tools & shallow test MWD- tool failed. LD MWD & work on same, shallow test- OK. TIH w/ BHA & 1 std DP. Slip & cut 115' drlg line. TIH to 7,100', fill pipe every 20 stds. Circulate & condition mud, 9.7+ ppg in/out. TIH, wash down to bottom. Drill from 9,771' to 10,123' 30.6 ft/hr) / Depth Angle Bit Size Mfg. Type Serial # Jets 6 x 22 Ulterra 15/35K 80TD/126DH x 22 Ulterra 15/35K 80TD/126DH 9771 RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr No. 1 PZ11 Diesel (gal) 12 Start 71 Received

17 Date: 01/09/2017 Rig: Norton Rig #2 Daily Cost: $88,224 Report #: 21 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $1,378,523 Drill from 10,123' to 10,460' ft/hr). Pump Hi-Vis LCM sweep & circulate hole clean. POOH to 9,540'- no excessive drag. TIH w/ full returns. Circulate bottoms up, mud 9.8 ppg in/out. TOOH, remove RCH at 9,280' & continue to TOOH. RU LD Truck, HSM & LD 6" DCs & directional tools. PU new directional tools & RIH as follows: 6-3/4, Executive 7/ Slick Motor + NM Pony DC + NM X/O + NMDC w/ MWD + NM X/O + NM Flex Collar. Shallow test Summary: directional tools. PU on 8-3/4" Hybrid Bit & continue to TIH w/ 16 Stands 4-1/2" DP. Check pump-in pressure = SPM. PU on X/O + NOV Agitator + X/O + 1 stand 4-1/2 DP & check pump-in pressure = SPM. Continue TIH w/ BHA on 4-1/2 DP. : TIH w/ Build assembly BHA to drill curve. 1:30 PM 3:00 PM 4:00 PM 5:00 PM 7:00 PM 10:00 PM 10:30 PM 1:00 AM 3:30 AM Daily ( - ) Drill from 10,123' to 10,460' ft/hr). Pump Hi-Vis LCM sweep & circulate hole clean. POOH to 9,540'- no excessive drag. TIH w/ full returns. CBU, MU 9.8ppg in/out. POOH, remove RCH at 9,280'. POOH. TOOH. RU LD Truck, HSM. LD 6" DCs & Directional Tools. PU new directional tools & shallow test. PU on 8-3/4" Hybrid Bit. TIH w/ BHA on 16 stands 4-1/2" DP. Check pump-in pressure = SPM. PU Agitator, check pump-in pressure = 480 Nova / Depth Angle Bit Size Mfg. Type Serial # Jets Depth Angle /4 Baker HughesKM624 Hybri x /4 Ulterra U613M PDC x 22 RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr Bit #6 Report: 1,1,CT,G,-,IN,NO,TD.

18 Date: 01/10/2017 Rig: Norton Rig #2 Daily Cost: $42,912 Report #: 22 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $1,421,435 TIH w/ curve BHA to 7,100', filled hole every 20 stds w/ full returns. Circulated bottoms up w/ 9.8 ppg mud in/out. TIH Executive picking up 4.5" DP from 9,995' to 10,460'. Slide & drill building curve hole section from 10,460' to 11,225 MD. Summary: Landed 11,225, w/ last 11,903 Inc = 71.2, Azm = Predicted 11,153 MD, Inc = 80.00, 342, 10, Total time to drill curve = 16.5 hours. : Circulating bottoms up, prep for short trip to 10,460'. 8:00 AM 8:30 AM 10:30 AM 11:00 AM 12:30 PM 6:00 PM 6:15 PM 6:40 PM 6:55 PM 8:35 PM 8:55 PM 10:45 PM 11:05 PM 11:45 PM 12:00 AM 1:15 AM 1:40 AM 3:50 AM Daily ( - ) TIH w/ curve BHA to 7,100' fill hole every 20 stds w/ full returns. CBU 9.8 ppg in/out. TIH to 9,995'- full returns. Service rig & TDS., change dies on TD grabber. Pick up 4.5" DP from 9,995' to Btm 10,460'. Slide drill building curve hole section from 10,460' to 10,715' ft/hr). Drilled from 10,715' to 10,755' 165 ft/hr) - WOB = 30 klbs; GPM = 340; RPMs = 55. Slide from 10,755' to 10,773' ft/hr) - WOB = 20 klbs; GPM = 486; 90L. Survey & 10,713', Inc = 28.17, Azm = Slide from 10,773' to 10,868' ft/hr) - WOB = 20 klbs; GPM = 486; TFO = 90L. Survey & 10,808', Inc = 33.27, Azm = Slide from 10,868' to 10,963' ft/hr) - WOB = 20 klbs; GPM = 486; TFO = 30L. Survey & 10,903', Inc = 47.31, Azm = Slide from 10,963' to 10,973' ft/hr) - WOB = 20 klbs; GPM = 447, TFO = 30L. Drill from 10,973' to 10,983' 40 ft/hr) - WOB = 30 klbs; GPM = 340; RPM = 55. Survey & 10,903', Inc = 47.31, Azm = Slide from 10,963' to 10,973' ft/hr) - WOB = 20 klbs; GPM = 447, TFO = 30L. Drill from 10,973' to 10,983' 40 ft/hr) - WOB = 30 klbs; GPM = 340; RPM = 55. Nova /8 Depth Angle Bit Size Mfg. Type Serial # Jets 4 x /4 30/30 6 x /4 Deviation RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr Depth Angle KM624 Hybrid

19 Date: 01/11/2017 Rig: Norton Rig #2 Daily Cost: $204,952 Report #: 23 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $1,626,387 Pumped sweep & circulated hole clean. Oscillate drill string 60', 450 gpm, 3,075# spp, 30 rpm. Short trip to 10,400'- no excessive drag, no fill on bottom. Pumped sweep & circulated hole clean, oscillate drill string 60', 450 gpm, 3,075# spp, 30 Executive rpm. Spotted 10.3 ppg pill from 11,225' to 10,400' (through curve). POOH to 10,000'. Circulate & mix slug. Change Summary: hydraulic hose on ST-80. PJSM & RU laydown machine. Pumped slug & began LD 4-1/2" drill string + agitator + XOs. TIH w/ 4-1/2" DP out of derrick & LD. LD directional tools, pulled wear bussing, changed out elevators & bails. RU csg crew, HSM & began RIH w/ 7.0", 26#, P-110, LTC csg. : RIH w/ 7" csg. 9:00 AM 10:00 AM 12:00 PM 1:00 PM 1:30 PM 2:00 PM 2:30 PM 7:00 PM 8:45 PM 9:15 PM 10:45 PM 12:15 AM 1:00 AM 2:00 AM Daily ( - ) Pump sweep & circulate hole clean, oscillate drill string 60', 450 gpm, 3,075# spp, 30 rpm. Short Pump trip sweep to 10,400'- & circulate no excessive hole clean, drag, oscillate no fill drill on string btm. 60', 450 gpm, 3,075# spp, 30 rpm. Spot 10.3 ppg pill from 11,225' to 10,400'. POOH to 10,000'. Circulate, mix slug. Service rig & TDS, change hydraulic hose on ST-80. PJSM & RU laydown machine. Pump slug & LD 4-1/2" drill string. LD 4-1/2" DP + agitator + XOs. TIH w/ 4-1/2" DP out of derrick. LD 4-1/2" DP. LD directional tools. Pull wear bussing. Change out elevators & bails. RU csg crew. HSM. RIH w/ 7.0", 26#, P-110, LTC csg. Pull wear bussing. Change out elevators & bails. RU csg crew. HSM. RIH w/ 7.0", 26#, P-110, LTC csg /8 4/6 -/ Depth Angle Bit Size Mfg. Type Serial # Jets KM624 Hybrid No. 1 4 x 18 U613M PDC No. 2 6 x 22 30/ RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr Baker Hughe Diesel (gal)

20 Date: 01/12/2017 Rig: Norton Rig #2 Daily Cost: $157,522 Report #: 24 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $1,783,909 RIH w/ 7.0", 26#/ft, P-110, LTC csg to 7,081'. Attempt to break 315 gpm, partial returns. WO 275 gpm. RU Rugged Energy Services pump truck & break 1.5 gpm, stage pump to 2 bpm & started losing mud. 1.5 bpm w/ full returns. Finish RIH w/ 7.0", 26#/ft, P-110, LTC csg to 11,225'. Circulate w/ pump 1.0 bpm stage up to 3.0 bpm. RD csg crew. RU cementers ground. HSM, RU cementer s floor. Mixed & pumped Stage 1 cement: Lead: 309 sx 50/50 POZ C + additives, 11.8 ppg, 2.45 cuft/sx; Tail: 150 sx 50/50 POZ C + additives, 14.2 ppg, 2.46 cuft/sx. Had full returns Executive throughout cement job. 300 bbls into displacement started losing returns. Bumped 12:05 AM w/ 1,450 psi, check Summary: floats- good. Drop DV Tool opening plug. Pressured up on plug to 720 psi & opened tool. Turned operations over to rig & began circulating 5.5 BPM. Started losing returns (100 bbls). RU pump truck & circulated WB w/ PT BPM- getting full returns. WOC. Safety meeting. Mixed & pumped Stage 2 Cement: Lead: 220 sx 50/50 POZ C + additives, 11.8 ppg, 2.46 cuft/sx; Tail: 61 sx 50/50 POZ C + additives, 14.2 ppg, 1.3 cuft/sx. Pumped job w/ full returns, closed stage tool w/ 1,980 8:10 AM. No cement to surface. Pressure test csg to 1,500 psi from DV 6,900 to surface- good test. : Testing 7" csg from DV 6,900' to 1,500 psi. 8:30 AM 9:30 AM 9:30 AM 5:00 PM 8:00 PM 12:00 AM 1:00 AM 6:00 AM RIH w/ 7.0", 26#/ft, P-110, LTC csg to 7,081'. Attempt to break 315 gpm, partial returns, WO 275 gpm TEE pump truck (Rugged). RU pump truck & break 1.5 gpm, stage pump to 2 bpm & started losing mud. 1.5 bpm w/ full returns. Finish RIH w/ 7.0", 26#/ft, P-110, LTC csg to 11,225'. Circulate w/ pump 1.0 bpm stage up to 3.0 bpm. RD csg crew. RU cementers ground. Hold safety meeting, RU cementers. Mixed & pumped Stage 1 cement: Lead: 309 sx 50/50 POZ C + additives, 11.8 ppg, 2.45 Drop DV Tool opening plug. Pressured up on plug to 720 psi & opened tool. Turned operations over to rig & began circulating 5.5 BPM. Started losing returns (100 bbls). RU pump truck & circulat Safety meeting. Mixed & pumped Stage 2 Cement: Lead: 220 sx 50/50 POZ C + additives, 11.8 ppg, 2.46 cuft/sx; Tail: 61 sx 5 -/ / Depth Angle Bit Size Mfg. Type Serial # Jets Baker Hughe No. 1 Diesel (gal) Ulterra No. 2 Start RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr Received PZ End Casing Detail: 247 jts + SJ - 7.0, 26#, P-110, LTC. 11,224, 11,176, DV 6,900. Marker 9, & 6, (from surface). Cement Detail: Stage 1: Lead 309 sx 50/50 POZ C + additives, 11.8 ppg, 2.46 cuft/sx. Tail 150 sx 50/50 POZ H + additives, 14.2 ppg, 1.26 cuft/sx. Bumped Plug w/ 1,450 psi, Floats held. 12:00 AM; 1/12/17. Opened Staging Tool w/ 720 psi. Stage 2: Lead 220 sx 50/50 POZ C + additives, 11.8 ppg, 2.46 cuft/sx. Tail 61 sx 50/50 POZ C + additives, 14.2 ppg, 1.26 cuft/sx. Used Rate ($/gal) Total Cost ($)

21 Tail 61 sx 50/50 POZ C + additives, 14.2 ppg, 1.26 cuft/sx. Closed Staging Tool w/ 1,980 psi. 8:10 AM; 1/12/17. No cement to surface.

22 Date: 01/13/2017 Rig: Norton Rig #2 Daily Cost: Report #: 25 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: Finished pumping stage 2 Cement: Lead sx 50/50 POZ C + additives, 11.8 ppg, 2.46 cuft/sx, Tail - 61 sx 50/50 POZ C + additives, 14.2 ppg, 1.3 cuft/sx. Pumped job w/ full returns, closed stage tool w/ :10 1/12/2017., Check floats, holding, bleed back 2 bbls. Pressured up to 1500 psi & recorded for 30 minutes. Good test. PJSM and rig down cementing Executive equipment. N/D pollution pan and BOP, pick up stack and set 7" C-22 casing slips. PJSM. Cut and dress 7" casing. Changed Summary: out liners on both MP's to 4.5" & changed out E-Brake on draw works. Nipple up BOP, changed out DP ram blocks to 4.0. Change out bail, elevators & PU 4" handling tools. Test BOP/ blinds, 4" manual valve & test choke, 250 low high. Cut & slip 90' of drill line. Rack & strap 4" drill pipe. Enter tally into Pason : Strapping BHA 9:30 AM 10:00 AM 10:00 AM 7:00 PM 10:30 PM 12:30 AM 2:45 AM 3:45 AM additives, 14.2 ppg, 1.3 cuft/sx. Pumped job w/ full returns, closed stage tool w/ :10 1/12/2017., Check floats, PJSM and rig down cementing equipment. MP's to 4.5", Change E-Brake on Dwks. Nipple up BOP, Change DP ram blocks to 4.0". Change out 4-1/2" pipe rams to 4" rams Change out bail, elevators & PU 4" handling tools Test BOP/ blinds, 4" manual valve & test choke, 250 low high Cut & slip 90' of drill line Rack & strap 4" drill pipe. Enter tally into Pason -/ / Depth Angle Bit Size Mfg. Type Serial # Jets Baker Hughe No. 1 Diesel (gal) Ulterra No. 2 Start RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr Received PZ End Changing out Equipment & tools to drill lateral w/ 4" Used Rate ($/gal) Total Cost ($)

23

24 Date: 01/14/2017 Rig: Norton Rig #2 Daily Cost: Report #: 26 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: Pick up and make up lateral BHA as follows: Ulterra 6.125: U613M PDC bit w/ 6 x 18 jets , 7/8, 3.8 Mud Motor + Double pin NM sub + NMDC w/mwd + NMDC + XO + 48 jts 4.0" 14#/ft S-135 DP + Agitator & safety sub. Surface test mud motor and MWD. PJSM with laydown crew, R/U laydown machine. (533 jnts 4.0" DP + 30 jts 4 HW DP on Executive location). Strap & Tally 4" 14#/ft S-135 DP with XT39 connection. P/U & RIH w/ DP drifting to 2.437" to 6,898'. Re-count DP Summary: on location, review and confirm tally & depth, TOH standing back 12 stands 4" DP. Load & strap HW 4" DP, PU & RIH w/ 30 jts 4" HW DP w/ XT-39 connections + 2 stds 4" DP out of derrick. Condition mud & circulate, check pumps. Tag & drill out DV 6889'. TIH 9 stds 4" DP out of derrick. PU & continue RIH w/ 4", 14#, S-135 DP w/ XT-39 connections. Tag 11,158' (reported Float 11,183'). RD PU/LD machine, install rotating head w/ new rubber & circulate bottoms up. Float Collar : 9:00 AM 9:30 AM 9:30 AM 8:00 PM 8:30 PM 9:00 PM 10:00 PM 11:00 PM 11:30 PM 12:00 AM 4:30 AM 5:00 AM Pick up and make up lateral BHA. Surface test mud mtr and MWD. PJSM with laydown crew, R/U laydown machine. ( 533 jnts 4.0" DP on Loc. ) SLM 4" 14#/ft S-135 DP with XT39 connection. P/U & drift (2.437") DP to 6,898' Count DP on location, review and confirm tally & depth TOH 12 stands 4" DP Load & strap HW 4" DP PU & RIH w/ 30 jts 4" HW DP w/ XT-39 connections + 2 stds 4", 14#, S-135 DP w/ XT-39 conn. Condition mud & circulate, check pumps Tag DV 6889', drill out DV Tool TIH 9 stds 4" out of derrick PU & continue RIH w/ 4", 14#, S-135 DP w/ XT-39 connections to 11,153' (Float 11,1') RD PU/LD machine 11/8 10 -/ // Depth Angle Bit Size Mfg. Type Serial # Jets 24.5k No No RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr Ulterra PZ11 14 Diesel (gal) Start Received End

25 Date: 01/15/2017 Rig: Norton Rig #2 Daily Cost: Report #: 27 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: Test Csg from 11173' to surface, to 1,500 psi for 30 mins. Received good chart. Drilled out FC + SJ + DS, fell out of 11,225. Drilled/ slide from 11,225' to 11,599' 41.6 ft/hr) Drilling WOB = 30 klbs, 60 RPMs, GPM. Sliding WOB = 20 klbs, GPM. Began losing pressure & differential pressure, TOH w/ 6 stands to 11,225'. Pressure test rig lines for leaks/ check pumps for wash-out, found all OK. TOH standing back to check down hole tools. Found hole in 4" Executive DP: Middle Jt of stand #21, Jt # 256, 9,649' below surface w/ 11,505. LD bad jt, PU new jt & TBIH w/ 4" DP out of Summary: derrick. Drilled/ Slide from 11,599' to 11,758' ft/hr). Drilling WOB = 20 klbs, 60 RPMs, 200 GPM. Sliding WOB = klbs, 200 GPM. 5 Hrs Sliding, 12.5 hrs Drilling Drilling 11,758' MD, ROP = 55 ft/hr, WOB = 20 klbs, ROT = 65 rpm, TOR = 8.1 kft-lbs, Diff Pres = 424 psi, Pump rate : = SPM, SPP = 2458 psi. 7:30 AM 9:30 AM 9:30 AM 5:00 PM 7:00 PM 7:30 PM 9:00 PM 10:15 PM 10:45 PM 12:30 AM Test Csg to 1500 psi for 30 mins, from 11173' to surface. Received good chart Drill out FC + SJ + DS, fell out of GPM. Rig Service GPM. Losing pressure & differential pressure, TOH w/ 6 stands to 11,225' Pressure test rig lines for leaks/ check pumps for wash-out, found all OK TOH standing back to check down hole tools. Found hole in 4" DP: Middle Jt of stand 21, Jt # 256, 9,649' below surface w/ 10(LD bad jt, PU new jt. TBIH w/ 4" DP out of derrick Drilled/ Slide from 11,599' to 11,758' ft/hr). Drilling WOB = 20 klbs, 60 RPMs, 200 GPM. Sliding WOB = k 15/ / / Depth Angle Bit Size Mfg. Type Serial # Jets k No No RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr Ulterra PZ11 14 Diesel (gal) 85 Start 90 Received 342 End

26 Date: 01/16/2017 Rig: Norton Rig #2 Daily Cost: $47,528 Report #: 28 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $2,024,701 Drill & slide from 11,758' to 12, ft/hr). Average parameters while drilling: WOB = 20 klbs, 60 RPMs, 200 GPM. Average parameters while sliding: WOB = klbs, 200 GPM. 3.5 hours sliding, 20 hours drilling. Recent Survey: MD = 12,595, INC = AZI = , TVD = 10,917.33, VS = '. Executive Footage in Zone: -30 RSD. Summary: Observed 2.5 formation up dip. Dip angle calculations sustaining 2.5. Note: Top of Zone = +38 RSD/ Base of Zone = -62 RSD. : Drilling 12,670' MD, ROP = 84.8 ft/hr, WOB = 20 klbs, ROT = 72 rpm, TOR = kft-lbs, Diff Pres = 395 psi, Pump Rate = 226 gpm, SPP = 2,834 psi. 3:00 PM 3:30 PM 3:30 PM 8:00 PM 8:30 PM 12:30 AM 2:00 AM 4:00 AM 4:30 AM Drill/ Slide from 11,758' to 12, ft/hr). Drilling WOB = 20 klbs, 60 RPMs, 200 GPM. Sliding WOB = klbs, 200 GPM. Service rig & TDS. Drill/ Slide from 12,071 to 12,228' 44.8 ft/hr). Drilling WOB = 20 klbs, 60 RPMs, 200 GPM. Sliding WOB = klbs, 200 GPM. Drill from 12,228' to 12,269' 41 ft/hr). WOB = 20 klbs, Pump Rate = 200 gpm, Rot = 65 rpms. Slide from 12,269' to 12,279' 20 ft/hr). WOB = 20 klbs, Pump Rate = 200 gpm, 180. Drill from 12,279' to 12,458' ft/hr). WOB = 20 klbs, Pump Rate = 200 gpm, Rot = 65 rpms. Slide from 12,458' to 12,478' 13.3 ft/hr). WOB = 20 klbs, Pump Rate = 200 gpm, 180. Drill from 12,478' to 12,552' 37 ft/hr). WOB = 20 klbs, Pump Rate = 200 gpm, Rot = 65 rpms. Slide from 12,552' to 12,562' 20 ft/hr). WOB = 20 klbs, Pump Rate = 200 gpm, 180. Drill from 12,562' to 12,670' 43.2 ft/hr). WOB = 20 klbs, Pump Rate = 225 gpm, Rot = 72 rpms. 3.5 Hrs Sliding, 20 hrs Drilling. 13/ / / Depth Angle Bit Size Mfg. Type Serial # Jets k No No RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr Ulterra PZ Diesel (gal) 170 Start 382 Received 0 End

27 Date: 01/17/2017 Rig: Norton Rig #2 Daily Cost: $50,456 Report #: 29 Current Depth: Progress Last 24 Hrs: 0 Cum Cost: $2,075,157 Drill & slid lateral from 12,670 to 13,768 MD, ft/hr). 14 hours drilling, 7 hours sliding, 3 hours surveying & connections. Average parameters while drilling: WOB = 20 klbs, ROT = 65 rpms, Pump Rate = 208 gpm. Average Executive parameters while sliding: WOB = 20 klbs, Pump Rate = 200 gpm. Summary: Most Recent Survey: MD = 13,727, INC = 94.65, AZI = , TVD = 10,871.90, VS = 2, RSD (at top of or just above miss lm) footage in zone. Observed 1.55 (up) formation dip. : Drilling 13,768' MD, ROP = 78.7 ft/hr, WOB = 16.6 klbs, Rot = 68 rpm, TOR = kft-lbs, Diff Pres = psi, Pump Rate = 211 gpm, SPP = 3,037 psi. 3:00 PM 4:00 PM 4:00 PM 7:30 PM 9:00 PM 10:00 PM 11:00 PM 12:30 AM 1:15 AM 3:30 AM 4:30 AM 6:00 AM Drill/ Slide from 12,670' to 13, ft/hr). Drilling WOB = 20 klbs, 60 RPMs, 220 GPM. Sliding WOB = klbs, 220 GPM. Service Drill/ Slide rig & from TDS. 13,108' to 13,306' 66 ft/hr). Drilling WOB = 20 klbs, 60 RPMs, 220 GPM. Sliding WOB = klbs, 220 GPM. Slide from 13,306' to 13,321'. WOB = 20 klbs, Pump Rate = 200 gpm, 150L. Drill from 13,321' to 13,401' 53 ft/hr). WOB = 20 klbs, Rot = 65 rpms, Pump Rate = 225 gpm. Slide from 13,401 to 13,431'. WOB = 20 klbs, Pump Rate = 225 gpm, 75 R. Drill from 13,431' to 13,495' 64 ft/hr). WOB = 20 klbs, Rot = 65 rpms, Pump Rate = 225 gpm. Slide from 13,495' to 13,535'. WOB = 20 klbs, Pump Rate = 208 gpm, 30 R. Drill from 13,535' to 13,579' 59 ft/hr). WOB = 20 klbs, Rot = 65 rpms, Pump Rate = 208 gpm. Slide from 13,579' to 13,609'. WOB = 20 klbs, Pump Rate = 200 gpm, 80 R. Drill from 13,609' to 13,673' 64 ft/hr). WOB = 20 klbs, Rot = 65 rpms, Pump Rate = 208 gpm. Slide from 13,673' to 13,697'. WOB = 20 klbs, Pump Rate = 200 gpm, 150 R. 12/ / / Depth Angle Bit Size Mfg. Type Serial # Jets k No No RPM WOB Pump Press. SPM GPM Ftg Hrs Ft/Hr Ulterra PZ11 Diesel (gal) 132 Start 528 Received 0 End