Series L7 Disconnect Switches (to 315A)...L29 Technical Information...L36 Dimensions...L38

Transcription

1 Series 7 Motor (to 100A)...2 Series 7 Enclosed (to 100A)...14 Technical Information...18 Dimensions...22 Series 7 (to 315A)...29 Technical Information...36 Dimensions...38 Series 10 Fusible and Non-Fusible...45 Series 10 Enclosed...50 Technical Information...51 Application Methods...55 Dimensions

2 Series 7 Motor (to 100A) Sprecher + Schuh s 7 line incorporates the latest modular design techniques to provide maximum functionality with the fewest number of parts. These rugged switches are compact, reliable and the ideal choice for all disconnect applications including motor disconnects per U-508 Part III. A device under this U listing meets the requirements as a motor controller or at motor disconnect. U508 approved device suitable as motor disconnect TIP! Manual Switching Devices: Control, oad or Fusible Which is Best For Your Application? Application Data Typical Control Switch Typical oad Break Switch Typical Fusible Switch To learn the basic differences between control, load and fusible disconnect switches and how to apply them, ask your Sprecher + Schuh representative for publication no: Tech-MSD Just the right switch for your application 7 are available in four frame sizes up to 100 amps (larger 7 s up to 315A can be found beginning on page 29). The smaller 7s come in six pole models, as well as three pole changeover switches. A full complement of switch handles and accessories including auxiliary contact blocks, ground and neutral terminals make the 7 line broad enough to tackle virtually any disconnect duty. Meets the toughest safety standards A generous 9mm gap between open contacts, combined with high short circuit withstand capabilities ensures a minimum probability of welding. All switches are touch safe to IP20, while most switch handles are rated for strong water jets to IP66. Excellent making and breaking characteristics provide a level of safety that, in many cases, exceeds international standards. Modular, flexible and easy to assemble The versatile 7 line is fully modular. All accessories snap-on and off without the use of tools, speeding assembly. The 7 s modular design minimizes inventory with features such as universal auxiliary contact blocks virtually every block fits all frame sizes. Both metal and plastic shaft extension systems are available to accommodate most panel depths. International standards and approvals 7 Motor are U isted (U508, Part III) and CSA approved (C22.2 No. 14). They also carry the CE Mark and meet IEC 947-1, 947-3, as well as IEC 207 requirements. They are approved in virtually every international market mm ( 1 13/32 ) 16A 45mm ( 1 3/4 ) 25A 32A 54mm ( 2 1/8 ) 40A 63A 72mm ( 2 13/16 ) 80A 100A

3 Full range of enclosed disconnects for any job From do-it-yourself to fully assembled, we offer a complete selection of three, four and six pole enclosed disconnects for any industrial application. The most economical choice is to configure your own design (Figure 1) by selecting one of the non-u/csa Approved ABS or Noryl enclosures from page 17 and completing it with your choice of 7 switch from pages 4 7. These enclosed disconnects are suitable for use in NEMA 4 type applications (not U isted). An assembled version of this enclosed disconnect is available with three or six poles from page 16 (Figure 2). A broad selection of assembled U isted enclosed disconnects is available on pages 14 and 15. Painted metal, stainless steel and polyester-fiberglass enclosures with three, four and six pole disconnect switches are available with all accessories (Figure 3). + Figure 1 Figure 2 Figure 3 How to order 7 motor disconnect switches A complete 7 Motor Switch is ordered with as little as two catalog numbers. The first number specifies the switch body and the second specifies the switch handle assembly. All 7 switch bodies come standard with a shaft and mounting screws for the switch handle assembly. Accessories such as shaft extensions and auxiliary contact blocks are ordered separately. First determine the switch you need from pages 4 7. Then turn to page 8 and 9 to choose a switch handle assembly. If necessary, see page 12 and 13 to determine the type and length of shaft extension you require. Auxiliary contact blocks, fourth poles, ground terminals and neutral terminals are found on page 10. Side Mount Accessories - page 10 Miscellaneous Accessories - page 11 Modular Shaft Extensions (A only) - page 12 Metal Shaft Extensions (A only) - page 13 7 E Switch Body Assemblies - page 4 & 5 A Switch Body Assemblies - page 6 & 7 Switch Handle Assemblies - pages 8 & 9 3

4 Motor Series 7 Front Mounted 3 Pole - 90 o Throw ➊ 3 Pole 1/1 3/2 5/3 2/T1 4/T2 6/T3 Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number 3 Pole E E E E E Amp Rating (encl.) U/CSA IEC/VDE/BS Ø Horsepower 240V V V Ø Horsepower 120V V Dimension - mm (inches) 63 (2-31/64) - Height 63 (2-31/64) - Height 72 (2-55/64) - Height 36 (1-27/64) - Width 45 (1-49/64) - Width 54 (2-1/8) - Width 51 (2-1/64) - Depth ➋ 60 (2-23/64) - Depth ➋ 74 (2-29/32) - Depth ➋ Price 3 Pole 1/1 3/2 5/3 7 2/T1 4/T2 6/T3 Catalog Num. Price Catalog Num. Price 3 Pole E E Amp Rating (encl.) U/CSA IEC/VDE/BS Ø Horsepower 240V V V Ø Horsepower 120V V Dimension - mm (inches) 90 (3-35/64) - Height 72 (2-27/32) - Width 90 (3-35/64) - Depth ➋ NOTE: arger amp 7 can be found beginning on page 29. ➊ Fourth pole side-mounted module available. See page 10. ➋ Dimension without shaft. 4 Discount Schedule B-6

5 Motor Series 7 Front Mounted 3 Pole Changeover and 6 Pole - 90 o Throw ➊ Changeover (Center OFF) Pole Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price Changeover E E E E E Pole E E E E E Amp Rating (encl.) U/CSA IEC/VDE/BS Ø Horsepower 240V V V Ø Horsepower 120V V (2-31/64) - Height 63 (2-31/64) - Height 72 (2-55/64) - Height Dimension - 90 (3-35/64) - Width 90 (3-35/64) - Width 108 (4-1/4) - Width mm (inches) 76 (3) - Depth ➋ 85 (3-11/32) - Depth ➋ 99 (3-57/64) - Depth ➋ 1 Changeover (Center OFF) Pole Catalog Number Price Catalog Number Price Changeover E E Pole E E Amp Rating (encl.) U/CSA IEC/VDE/BS Ø Horsepower 240V V V Ø Horsepower 120V V (3-35/64) - Height Dimension (5-43/64) - Width mm (inches) 115 (4-17/32) - Depth ➋ ➊ 3 Pole Changeover Switch has center OFF ➋ Dimension without shaft. 7 Discount Schedule B-6 5

6 Motor Series 7 Base Mounted 3 Pole - 90 o Throw ➊ 3 Pole 1/1 3/2 5/3 2/T1 4/T2 6/T3 Catalog Number Price Catalog Num. Price Catalog Num. Price Catalog Num. Price Catalog Num. Price 3 Pole A A A A A Amp Rating (encl.) U/CSA IEC/VDE/BS Ø Horsepower 240V V V Ø Horsepower 120V V Dimension - mm (inches) 63 (2-31/64) - Height 63 (2-31/64) - Height 72 (2-55/64) - Height 36 (1-27/64) - Width 45 (1-49/64) - Width 54 (2-1/8) - Width 51 (2-1/64) - Depth ➋ 60 (2-23/64) - Depth ➋ 74 (2-29/32) - Depth ➋ 3 Pole 1/1 3/2 5/3 2/T1 4/T2 6/T3 7 Catalog Num. Price Catalog Num. Price 3 Pole A A Amp Rating (encl.) U/CSA IEC/VDE/BS Ø Horsepower 240V V V Ø Horsepower 120V V Dimension - mm (inches) 90 (3-35/64) - Height 72 (2-27/32) - Width 90 (3-35/64) - Depth ➋ NOTE: arger amp 7 can be found beginning on page 29. ➊ Fourth pole side-mounted module available. See page 10. ➋ Dimension without shaft. 6 Discount Schedule B-6

7 Motor Series 7 Base Mounted 3 Pole Changeover and 6 Pole - 90 o Throw ➊ Changeover (Center OFF) 6 Pole Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price Changeover A A A A A Pole A A A A A Amp Rating (encl.) U/CSA IEC/VDE/BS Ø Horsepower 240V V V Ø Horsepower 120V V (2-31/64) - Height 63 (2-31/64) - Height 72 (2-55/64) - Height Dimension - 90 (3-35/64) - Width 90 (3-35/64) - Width 108 (4-1/4) - Width mm (inches) 85 (3-11/32) - Depth ➋ 89 (3-1/2) - Depth ➋ 103 (4-1/16) - Depth ➋ Changeover (Center OFF) 6 Pole Catalog Num. Price Catalog Num. Price Changeover A A Pole A A Amp Rating (encl.) U/CSA IEC/VDE/BS Ø Horsepower 240V V V Ø Horsepower 120V V Dimension - mm (inches) 90 (3-35/64) - Height 144 (5-43/64) - Width 119 (4-17/32) - Depth ➋ ➊ 3 Pole Changeover Switch has center OFF ➋ Dimension without shaft. Discount Schedule B-6 7

8 Motor Series 7 Switch Handle Assemblies (A and E ) Switch Handle Assembly ➊ Color Mounting Method Protection Rating For use with... Frame Size egend ➋ Catalog Number Price 7 Type A Type E Type I Type Silver egend ➋ Black Knob Silver egend ➋ Black Knob ➌ Yellow egend ➋ Red Knob Yellow egend ➋ Red Knob ➌ Silver egend ➋ Black Knob Screw Fixing ➊ IP66 A/E A 48 X 48 IP66 A/E A ➎ 64 X 64 IP66 A/E A 88 X 88 Central Nut IP66 E A 48 X 48 Screw Fixing ➊ IP66 A/E A 48 X 48 IP66 A/E A ➎ 64 X 64 Central Nut IP66 E A 48 X 48 Screw Fixing ➊ IP66 A/E A 48 X 48 IP66 A/E A ➎ 64 X 64 IP66 A/E A 88 X 88 Central Nut IP66 E A 48 X 48 Screw Fixing ➊ IP66 A/E A 48 X 48 IP66 A/E A ➎ 64 X 64 Central Nut IP66 E A 48 X 48 Screw Fixing ➊ IP66 A/E A 48 X 62 IP66 A/E A 64 X 78 O-I OFF-ON FS2-A FS2-A-4-175I ➍ FS2-A O-I OFF-ON FS2-A FS2-A-6-175I ➍ FS2-A O-I OFF-ON FS2-A FS2-A-8-175I ➍ FS2-A O-I OFF-ON O-I OFF-ON FC2-A FC2-A-4-175I FS2-E FS2-E-4-175I ➍ FS2-E O-I OFF-ON FS2-E FS2-E-6-175I ➍ FS2-E O-I OFF-ON O-I OFF-ON FC2-E FC2-E-4-175I FS2-I FS2-I-4-175I ➍ FS2-I O-I OFF-ON FS2-I FS2-I-6-175I ➍ FS2-I O-I OFF-ON FS2-I FS2-I-8-175I ➍ FS2-I O-I OFF-ON O-I OFF-ON FC2-I FC2-I-4-175I FS FS I ➍ FS O-I OFF-ON O-I OFF-ON O-I OFF-ON O-I OFF-ON FS FS I FC FC I FS2-S FS2-S-4-175I FS2-S FS2-S-6-175I Type S ➍ FS2-S ➊ Mounting screws included with Switch Body Assembly. ➋ For blank legend plate, substitute 000 for last three digits in catalog number. Example: FS2-A ➌ ockable in OFF position, ON position or both. ➍ Only for use with 3 Pole Changeover switch. ➎ Only for use with A/E three pole Changeover. Use 88 x 88 Switch Handle for 80 and 100A Changeover Switch. 8 Discount Schedule B-6 B-4

9 Motor Series 7 Switch Handle Assemblies (A and E ) Switch Handle Assembly ➊ Type G Type N Color Gray Frame Black Handle ➋ Yellow Frame Red Handle ➋ Mounting Method Screw Fixing ➊ Protection Rating For use with... Frame Size IP66 A/E x 54 IP66 IP66 Type 3/3R/12 A A E A 67 x 67 A/E A 90 x 90 Central Nut IP66 E A 67 x 67 Screw Fixing ➊ IP66 A/E x 54 IP66 IP66 Type 3/3R/12 A A E A 67 x 67 A/E A 90 x 90 Central Nut IP66 E A 67x67 egend ➋ O I OFF ON O I OFF ON O I OFF ON O I OFF ON O I OFF ON O I OFF ON O I OFF ON O I OFF ON Catalog Number Price Disc Sch FS7-G B-6 FS2-G B-4 FS2-G B-4 FC2-G B-4 FS7-N B-6 FS2-N B-4 FS2-N B-4 FC2-N B-4 Yellow Frame Red Handle - With Defeater Screw Fixing ➊ Type 4X IP66 A A 76 x 76 OFF - ON 10-HS4E ➌ 56 B-7 Type R Black Frame Black Handle With Defeater Screw Fixing ➊ Type 4X IP66 A A 76 x 76 OFF - ON 10-HS4 ➌ 56 B-7 Type R Special OEM Packaging Available A selection of switches and operators is available for purchase as a kit in a single carton with one catalog number., operators and accessories are also available in bulk packaging. Contact your Sprecher + Schuh representative for more information. 7 ➊ Mounting screws included with Switch Body Assembly. ➋ ockable in OFF position with up to 3 padlocks. ➌ For A base mount switches only. Requires R-type Switch Handle Shaft Extension. See page 13. Discount Schedule B-4 B-7 B-6 9

10 Motor Series 7 Auxiliary Contact Blocks Aux. Contact Block Contact Configuration For use with... One NO (Early Break) ➊ Catalog Number Price E7-16 E7-16-P-D10 37 E E7-P-D10 31 A7-16 A7-16-P-D10 37 A A7-P-D10 31 One NO and One NC (Instantaneous) E E7-P A A7-P Fourth Pole Fourth Pole Contact Configuration N N For use with... Early Make-ate Break Catalog Number Price E7-16 E7-16-NP 30 E7-25 E7-25-NP 31 E7-32 E7-32-NP 38 E7-40 E7-40-NP 46 E7-63 E7-63-NP 54 E7-80 E7-80-NP 58 E7-100 E7-100-NP 78 A7-16 A7-16-NP 30 A7-25 A7-25-NP 31 A7-32 A7-32-NP 38 A7-40 A7-40-NP 46 A7-63 A7-63-NP 54 A7-80 A7-80-NP 58 A7-100 A7-100-NP 78 One NOEM and One NCB (Make Before Break) E E7-P A A7-P Two NO and Two NC (Instantaneous) Accessory Mounting Guide 43 E E7-P A A7-P Various accessories can be mounted simultaneously on both the A7 (base mount) and E7 (front mount) switch bodies. The drawings below illustrate which combinations are possible. 1-4 Pole Auxiliary Contact or 1-2 Pole Auxiliary Contact or Grounding Terminal or Additional Pole Ground & Neutral Terminals Terminal Contact Configuration PE PE N N For use with... Ground Terminal Catalog Number Price A7-16 A7-16-PE 18 A7-25 & 32 A7-32-PE 20 A7-40 & 63 A7-63-PE 27 A7-80 & 100 A7-100-PE 34 E7-16 E7-16-PE 18 E7-25 & 32 E7-32-PE 20 E7-40 & 63 E7-63-PE 27 E7-80 & 100 E7-100-PE 34 Neutral Terminal 1-4 Pole Auxiliary Contact or 1-2 Pole Auxiliary Contact or Grounding Terminal A7-16 A7-16-TN 18 A7-25 & 32 A7-32-TN 20 A7-40 & 63 A7-63-TN 27 A7-80 & 100 A7-100-TN 34 E7-16 E7-16-TN 18 E7-20 & 32 E7-32-TN 20 E7-40 & 63 E7-63-TN 27 E7-80 & 100 E7-100-TN 34 ➊ All N.O. Early Break Contact Blocks mount on the left and/or right side by themselves, or with -NP, -PE, -TN aux on the opposite side. Stacking additional aux contacts on these blocks is not possible. 7 Neutral Terminal or 1-2 Pole Auxiliary Contact or 1-4 Pole Auxiliary Contact Additional Pole or Neutral Terminal or 1-2 Pole Auxiliary Contact or 1-4 Pole Auxiliary Contact E Switch Body (front mount) A Switch Body (base mount) 10 Discount Schedule B-6

11 Motor Series 7 7 Switch Accessories Accessory Description Catalog Number Price Disc Sch (Reducer not included) End Shaft - for E switch ➋ (one 44mm shaft supplied standard with all switches) Plastic 2-G B-4 Metal 7-G3688 ➊ 4.25 B-6 Terminal cover - 3 pole E/A C B-6 E/A7-25/ C B-6 E/A7-40/ C B-6 E/A7-80/ C B-6 Terminal cover - 4 pole E/A7-25/ C B-6 E/A7-40/ C B-6 E/A7-80/ C B-6 6 Pole Mechanical Coupling - joins two 7 switches (front or base mount) to form a 6 pole switch (includes 44 mm metal End Shafts for both E and A switch) E G3821 ➋ B-6 E/A7-25 & 32 7-G3660 ➋ B-6 E/A7-40 & 63 7-G3661 ➋ B-6 E/A7-80 & G3662 ➋ B-6 Snap-on Nameplate & Holder Snaps on to switch handle frames of the following sizes: For 48x48, 64x64 & 67x67 2-G B-4 For 88x88, 90x90 7-G B-6 Nameplate for Snap-on Holder fits cat. # 2-G3667 & 2-G3515 For 2-G3667 Main Switch 2-G3667A 4.50 B-4 Emergency Off 2-G3667H 4.50 B-4 For 2-G3515 Main Switch 2-G3515A B-4 Emergency Off 2-G3515H B-4 ➊ E pole switches and A pole switches come standard with a 44mm metal End Shaft. E pole switches and A7-16-xxxx 6-pole switches come standard with a 44mm plastic End Shaft. ➋ When using mechanical coupler to join two E7 or A7 three pole switches, terminal markings will be: To obtain terminal markings from pages 5 and order six pole switch Discount Schedule B-4 B-6 B-6 11

12 Motor Series 7 Modular shaft extension system Shaft Extension Modules are ideal for lengthening the shaft of an A7 switch up to 144mm ( 5.5 ). These rugged polycarbonate modules are 24mm ( 15/16 ) long and snap on piggyback to one another without the use of tools. Strong center shafts interlock as each module is snapped together. The standard 44mm End Shaft supplied with every A7 switch connects the last Extension Module with the Switch Handle Assembly. End Shafts of 52 and 57mm are also available, making this modular system versatile, fast and economical. Shaft Extension Modules are supplied two per package. Modular Shaft Extension Components ➌ Component Description Catalog Number Price Disc Sch 44mm End Shaft - one 44mm shaft supplied standard with all switches Plastic shaft A2-G B-4 Metal shaft 7-G3687 ➋ 4.25 B-6 52mm End Shaft - Plastic shaft A2-G B-4 Metal shaft 7-G3707 ➋ 4.50 B-6 57mm End Shaft - Plastic shaft A2-G B-4 A7 Switch Body Extension Modules - Two per package, priced per package A2-G B-4 7 Determining modular shaft extension components Determine Mounting Depth. This is the distance from the inside mounting surface of the enclosure to the outside surface of the enclosure cover. See diagram below for details. ➊ Mounting Depth If necessary convert Mounting Depth inches to millimeters (inches x 25.4 = millimeters). NOTE: Table is based on a standard 3 or 4 pole switch body. For 6 pole switches, deduct 25mm from the overall Mounting Depth before referring to table. In the Modular Shaft Extension Table to the right, find the Mounting Depth in the column under the appropriate A7 Switch Body. Order the End Shaft and number of Extension Modules required for that Mounting Depth. ➊ For DIN rail mounted devices, remember to deduct the offset distance provided by the rail. For example, deduct 2.5mm from the Mounting Depth for switch bodies mounted on DIN rail. ➋ E pole switches and A pole switches come standard with a 44mm metal End Shaft. E pole switches and A7-16-xxxx 6-pole switches come standard with a 44mm plastic End Shaft. ➌ Order additional shafts for E (front mount switches) from page 11. Modular Shaft Extension Table Number of Extension Modules Required End Shaft Switch Body A7-16 Mounting Depth (mm) ➊ Switch Body A7-25/32 Switch Body A7-40/63 Switch Body A7-80/ mm ➋ mm mm mm ➋ mm mm mm ➋ mm mm mm ➋ mm mm mm ➋ mm mm mm ➋ mm mm mm ➋ mm mm Discount Schedule B-4 B-6 B-6

13 Motor Series 7 Metal shaft extension system Adjustable metal shaft extensions snap on securely to A7 switches via the same quick-connect design as shaft extension modules. Metal shafts are equipped with a door interlock and a padlock hasp for locking out the switch after the enclosure is opened (for outside lockout, select a Switch Handle Assembly with lockout capability). Metal Shaft Extension Components (A ) Component Catalog Number Price 1 A2-G3393 ➌ 37 ength: mm For switching positions: 0 A7 Switch Body ength: mm For switching positions: 0 1 A2-G3394 ➌ 48 Two standard lengths of these unique adjustable shafts are available. Metal shaft extensions mate with any of the standard Switch Handle Assemblies on pages 8 and 9. All necessary hardware is supplied with the shaft. Determining metal shaft extension Determine Mounting Depth. This is the distance from the inside mounting surface of the enclosure to the outside surface of the enclosure cover. See diagram below for details. ➊ Insert - For modifying metal shaft for use with 3 Pole Changeover (not lockable). Metal Shaft Extension Table Metal Shaft Extension Switch Body A7-16 Mounting Depth (mm) ➊ Switch Body A7-25/32 A2-G Switch Body A7-40/63 Switch Body A7-80/100 A2-G ➋ ➋ ➋ ➋ A2-G Mounting Depth R-type Switch Handle Shaft Extensions Only select shaft extension from this table if ordering the R-type (U Type 4X) Switch Handle (page 9). Select shaft after figuring overall Mounting Depth. R-type Switch Handle Shaft Extension (typical) If necessary convert Mounting Depth inches to millimeters (inches x 25.4 = millimeters). NOTE: Tables are based on a standard 3 or 4 pole switch body. For 6 pole switches, deduct 25mm from overall Mounting Depth before referring to table. In the Metal Shaft Extension Table to the right, find the Mounting Depth in the column under the appropriate A7 Switch Body. Order the Metal Shaft Extension required for that Mounting Depth. Mounting Depth (mm) ➊ Catalog A7-16 A7-25/32 A7-40/63 A7-80/100 Number Price A2-G-194R A2-G-194R A2-G-194R A2-G-194R A2-G-194R A2-G-194R A2-G-194R A2-G-194R1-115 Adjustable R-type Switch Handle Shaft Extension 7 ➊ For DIN rail mounted devices, remember to deduct the offset distance provided by the rail. For example, deduct 2.5mm from the Mounting Depth for switch bodies mounted on DIN rail. ➋ This dimension can be reduced another 55mm by cutting the plastic sleeve and further cutting the metal shaft. ➌ If using Metal Shaft Extension System with 3 Pole Changeover, purchase insert to modify for three position switching. ➍ Use Discount Schedule B G3675 ➍ Discount Schedule B-6 B-4 13

14 Enclosed Motor Series 7 7 Enclosed Motor s (U and CSA Approved Enclosures) ➊➎ Painted Steel -U Type 1/3/12/4 Operator - IP66, U Type 3, 12 Nonmetallic - U Type 1/3/12/4 Operator - IP66, U Type 3, 12 Nonmetallic - U Type 4/4X Operator - U Type 4X Stainless Steel - U Type 4/4X Operator - U Type 4X Amp/Horsepower Rating 7 U/ CSA Amps 1Ø Horsepower 3Ø Dimension 120V 240V 240V 480V 600V Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price 3 Pole - ON/OFF A WN 241 A A CN 275 C A CR 335 C A SR 931 A A WN 258 A A CN 292 C A CR 353 C A SR 950 A A WN 275 A A CN 310 C A CR 370 C A SR 970 A A WN 301 A A CN 338 C A CR 396 C A SR 995 A A WN 333 A A CN 368 C A CR 428 C A SR 1028 A A WN 376 B A CN 533 D A CR 602 D A SR 1481 B A WN 424 B A CN 581 D A CR 649 D A SR 1529 B 4 Pole - ON/OFF ➍ A WN 265 A A CN 301 C A CR 359 C A SR 959 A A WN 288 A A CN 325 C A CR 383 C A SR 983 A A WN 312 A A CN 348 C A CR 406 C A SR 1006 A A WN 357 A A CN 383 C A CR 443 C A SR 1041 A A WN 387 A A CN 421 C A CR 482 C A SR 1081 A A WN 434 B A CN 591 D A CR 686 D A SR 1539 B A WN 501 B A CN 658 D A CR 727 D A SR 1606 B 6 Pole - ON/OFF A WN 299 B A CN 467 D A CR 479 D A SR 1359 B A WN 338 B A CN 501 D A CR 559 D A SR 1438 B A WN 376 B A CN 535 D A CR 639 D A SR 1518 B A WN 439 B A CN 596 D A CR 654 D A SR 1533 B A WN 492 B A CN 649 D A CR 707 D A SR 1587 B Modifications (Factory Assembled) ➋ Description Catalog Number Suffix Adder Ground Terminal For A7-16 -PE For A7-25 & 32 -PE For A7-40 & 63 -PE For A7-80 & 100 -PE Neutral Terminal For A7-16 -TN ➌ For A7-25 & 32 -TN ➌ For A7-40 & 63 -TN ➌ For A7-80 & 100 -TN ➌ Dimension Dimension NOTE: All IP66, U Type 3/12 Enclosed s come standard with a round, yellow and red, screw fixing handle (Type N) with ON/OFF marking. For a round gray and black handle, change N to G. Example: change A WN to A WG. For a gray and black square handle (Type A), change N to A. Example: change A WN to A WA. All Type 4X Enclosed s come standard with a round yellow and red handle with defeatable door interlock (Type R) and ON/OFF marking. See pages 8 and 9 for descriptions of all Switch Handle Assemblies. Dimension ➊ U/CSA Approved enclosures do not provide for knockouts. Wire opening must be drilled by user. ➋ Up to two modifications available per Enclosed (one modification possible on 4 pole switches). ➌ Not available on four pole switches. ➍ One additional factory modification possible. ➎ Non-metallic enclosures are fiberglass reinforced polyester type. 14 Discount Schedule B-6

15 Enclosed Motor Series 7 7 Enclosed Motor s (U and CSA Approved Enclosures) ➊ Painted Steel -U Type 1/3/12/4 Operator - IP66, U Type 3, 12 Nonmetallic - U Type 1/3/12/4 Operator - IP66, U Type 3, 12 Nonmetallic - U Type 4/4X Operator - U Type 4X Stainless Steel - U Type 4/4X Operator - U Type 4X Amp/Horsepower Rating U/CSA Amps 1Ø Horsepower Modifications (Factory Assembled) ➋ 3Ø Dimension 120V 240V 240V 480V 600V Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price Dimension 3 Pole - ON/OFF (with 1 NOEM and 1 NCB - Make Before Break) A WN-P A A CN-P C A CR-P C A SR-P A A WN-P A A CN-P C A CR-P C A SR-P A A WN-P A A CN-P C A CR-P C A SR-P A A WN-P A A CN-P C A CR-P C A SR-P A A WN-P A A CN-P C A CR-P C A SR-P A A WN-P B A CN-P D A CR-P D A SR-P B A WN-P B A CN-P D A CR-P D A SR-P B 4 Pole - ON/OFF (with 1 NOEM and 1 NCB - Make Before Break) ➌ A WN-P A A CN-P C A CR-P C A SR-P A A WN-P A A CN-P C A CR-P C A SR-P A A WN-P A A CN-P C A CR-P C A SR-P A A WN-P A A CN-P C A CR-P C A SR-P A A WN-P A A CN-P C A CR-P C A SR-P A A WN-P B A CN-P D A CR-P D A SR-P B A WN-P B A CN-P D A CR-P D A SR-P B 6 Pole - ON/OFF (with 1 NOEM and 1 NCB - Make Before Break) A WN-P B A CN-P D A CR-P D A SR-P B A WN-P B A CN-P D A CR-P D A SR-P B A WN-P B A CN-P D A CR-P D A SR-P B A WN-P B A CN-P D A CR-P D A SR-P B A WN-P B A CN-P D A CR-P D A SR-P B Description Catalog Number Suffix Adder Ground Terminal For A7-16 -PE For A7-25 & 32 -PE For A7-40 & 63 -PE For A7-80 & 100 -PE Neutral Terminal For A7-16 -TN For A7-25 & 32 -TN For A7-40 & 63 -TN For A7-80 & 100 -TN NOTE: All IP66, U Type 3/12 Enclosed s come standard with a round, yellow and red, screw fixing handle (Type N) with ON/OFF marking. For a round gray and black handle, change N to G. Example: change A WN to A WG. For a gray and black square handle (Type A), change N to A. Example: change A WN to A WA. All Type 4X Enclosed s come standard with a round yellow and red handle with defeatable door interlock ( Type R ) and ON/OFF marking. See page 8 and 9 for descriptions of all Switch Handle Assemblies. Dimension Dimension 7 ➊ U/CSA Approved enclosures do not provide for knockouts. Wire opening must be drilled by user. ➋ One modification available per Enclosed (no modifications available on 4 pole). ➌ Factory modifications not available. ➍ Nonmetallic enclosures are fiberglass reinforced polyester type. Discount Schedule B-6 15

16 Enclosed oad Series Y7 Y7 Enclosed oad (IP Rated Enclosures) ➊ Plastic - IP66 ABS Enclosure Operator - IP66, Red/Yellow (Type N) Plastic - IP66 ABS Enclosure Operator - IP66, Gray/Black (Type G) Plastic - IP66 ABS Enclosure Operator - IP66, Silver/Black (Type A) Amp/Horsepower Rating U/ CSA Amps 1Ø Horsepower 3Ø 120V 240V 240V 480V 600V Catalog Number Price Catalog Number Price Catalog Number Price 3 Pole - ON/OFF Y7-16M-1753-N4 131 Y7-16M-1753-G4 131 Y7-16M-1753-A Y N6 152 Y G6 152 Y A Y N6 169 Y G6 169 Y A Y N6 225 Y G6 225 Y A Y N6 255 Y G6 255 Y A Y N6 316 Y G6 316 Y A Y N6 363 Y G6 363 Y A Pole - ON/OFF Y7-16M-1756-N6 180 Y7-16M-1756-G6 180 Y7-16M-1756-A Y N6 287 Y G6 287 Y A Y N6 321 Y G6 321 Y A Y N6 366 Y G6 366 Y A Y N6 472 Y G6 472 Y A6 462 Assembled 7 Switch Description Function Color Circuit Poles U/CSA Amps Catalog Number Price Type Q oad Switch - This pre-assembled switch is designed for panels with standard 45mm cutouts. The specially designed switch handle also makes it ideal for mounting within a distribution panel when ready access to the operator is not desired. Finger-proof to IP ON-OFF 90 Switching Gray face/ Black Handle 1/1 3/2 5/3 2/T1 4/T2 6/T A Q A Q Emergency Off Switch - This yellow and red pre-assembled switch is designed as an Emergency Off for panels with standard 45mm cutouts. The specially designed switch handle also makes it ideal for mounting within a distribution panel when a color coded OFF switch is desired. Fingerproof to IP20 with provision for locking with one padlock. 1 0 ON-OFF 90 Switching Yellow face/ Red handle 1/1 3/2 5/3 2/T1 4/T2 6/T A R A R 109 ➊ Suitable for use in NEMA 4 type applications (not U listed). 16 Discount Schedule B-6

17 Enclosed oad Series Y7 Thermoplastic Enclosures (IP Rated) Accessory Description Enclosure Size ABS Enclosure For High Impact Applications IP66, U94 Flame Resistance - HB For use with... Poles Shaft Required... Catalog Number With pre-drilled holes for 64 x (W) x 150 (H) x 86 (D) A / 4 A2-G3194 A2-G B-4 operator or larger 95 (W) x 150 (H) x 111 (D) A2-G B (W) x 180 (H) x 105 (D) A With switch 7-G B-6 A / 4 Supplied with enclosure 175 (W) x 230 (H) x 120 (D) A With switch 7-G B-6 A / 4 Supplied with enclosure Without holes 95 (W) x 150 (H) x 86 (D) A2-G B-4 95 (W) x 150 (H) x 111 (D) A2-G B-4 Noryl Enclosure For Corrosion Prone Applications IP66, U94 Flame Resistance - VO With pre-drilled holes for 64 x 64 operator or larger Price 95 (W) x 150 (H) x 86 (D) A / 4 A2-G3194 A2-G B-4 95 (W) x 150 (H) x 111 (D) A2-G B (W) x 180 (H) x 105 (D) A With switch 7-G B-6 A / 4 Supplied with enclosure 175 (W) x 230 (H) x 120 (D) A With switch 7-G B-6 A / 4 Supplied with enclosure Without holes 95 (W) x 150 (H) x 86 (D) A2-G B-4 95 (W) x 150 (H) x 111 (D) A2-G B-4 Disc Sch Additional Ground & Neutral Terminals - (Provision for two. One included with enclosure) A2-G G All All 7-G G B-6 B-4 7 Discount Schedule B-4 B-6 B-6 17

18 Technical Information Series 7 Motor Technical Information Performance Data 16A 25A 32A 40A 63A 80A 100A Aux. Cont. 7 Rated operational voltage U e U/CSA [V] IEC ➊ [V] Rated insulation voltage U i U/CSA [V] IEC [V] Rated impulse voltage U imp U/CSA [kv] Test voltage U i 1 minute [kv] Rated Frequency [Hz] 50/60 50/60 50/60 50/60 50/60 50/60 50/60 50/60 Conventional free air thermal current I th ➊ [A] ➋ Conventional enclosed thermal current I th ➊ [A] Rated Current I e ➊ AC-1 AC-21A Rated Power P e AC-23A AC-3 Non-inductive or only slightly inductive loads 690V [A] Switching of resistive loads with slight overload Occasional switching of 3Ø motors and other highly inductive loads (criterion for selecting main switches) Squirrel cage motors; starting and stopping of running motors 230V [kw] V [kw] V [kw] V [kw] V [kw] V [kw] Short circuit current (Type 2 coordination) Rated conditional short circuit current 400/415V [ka] Maximum fuse rating of circuit (type g, G) [A] Rated short-time current 1cw, 1s [A] Rated breaking capacity AC23A (cosϕ 0.45) 230V [A] V [A] V [A] DC switching capacity Rated current I e 48V [A] pole 110V [A] V [A] V [A] DC-21A For resistive loads, 96V [A] T< 1 ms 2 poles 110V [A] U e max = 660V in series 220V [A] V [A] V [A] V [A] poles 220V [A] in series 440V [A] V [A] Rated power P e 90V [kw] DC-23A, DC-3, DC-5 3 poles 110V [kw] For inductive loads, in series 220V [kw] T< 15 ms 440V [kw] V [kw] ➊ See Conformity to Standards on next page. ➋ Also suitable for SEV Discount Schedule B-6

19 Technical Information Series 7 Motor Technical Information (continued) U/CSA Data 16A 25A 32A 40A 63A 80A 100A Aux. Cont. Continuous current [A] Heavy Pilot Duty [AC] A600 A600 A600 A600 Standard Duty [DC] Q600 Motor Rating 60Hz 120V [FA] [HP] V [FA] Single phase, 2 poles [HP] V [FA] [HP] V [FA] [HP] V [FA] [HP] V [FA] Three phase [HP] V [FA] [HP] V [FA] [HP] Short Circuit Ratings Maximum short circuit prospective fault current, RMS symmetrical, 600 VAC max. When protected by Class K5 fuses, maximum amperes of rated fuse [A] [A] Mechanical Data 16A 25A 32A 40A 63A 80A 100A Aux. Cont. Protection class according to IEC 529 Motor rating 60 Hz Actuators IP66 IP66 IP66 IP66 IP66 Switch bodies IP20 IP20 IP20 IP20 IP20 Mechanical life [millions of operations] Maximum wire gauges Terminal size per IEC A4 A6 A7 A9 2xA2 Fine strands 1/2 [AWG] (1)16 10/(2)16 12 (1)14 8/(2)14 10 (1)12 4/(2)12 8 (1)10 1/(2) conductor [mm 2 ] (1)1 10/(2)1 4 (1)1.5 16/(2)1.5 6 (1)2.5 25/(2) (1)4 50/(2) Rigid wire 1/2 [AWG] (1)16 10/(2)16 12 (1)14 8/(2)14 10 (1)12 4/(2)12 8 (1)10 1/(2) conductor [mm 2 ] (1)1.5 6/(2)1.5 4 (1)1.5 10/(2)1 6 (1)2.5 16/(2) (1)4 35/(2) Tightening Torque max. [lb-in] [Nm] Ambient Temperature Operation [ C] ºC ( ºF) Storage [ C] ºC ( ºF) Conformity to Standards: ➊ IEC 207, IEC 947-1, IEC ow voltage switchgear and control gear part 3:, disconnectors, switch-disconnectors and fusecombination units. CE U 508: Industrial Control Equipment CSA: C22.2 No. 14: Industrial Control Equipment ➊ A(E)-16 switches are cu approved. Approvals: ➊ U isted (File No. E54612 NRV) CSA Certified (R 13002) Meets IEC, VDE and BS standard requirements IEC/CE Marked (Per EN ) 7 Discount Schedule B-6 19

20 Technical Information IP Ratings Definitions IP Ratings Definitions IP Ratings Definitions The first IP number (left side of chart) is protection against solid objects. The second IP number (across top) is protection against liquids. The chart itself shows degrees of protection according to IEC 529. No protection Protected against vertically falling drops of water (condensation) Protected against dripping water with enclosure up to 15 from vertical Protected against sprayed water up to 60 from vertical Protected against sprayed water from all directions (limited ingress permitted) Protected against low pressure water jets from all directions (limited ingress permitted) Protected against strong jets of water from all directions Protected against immersion up to one meter Protected against long periods of immersion under pressure IP 0 IP 1 IP 2 IP 3 IP 4 IP 5 IP 6 IP 7 IP 8 1 meter IP0 IP00 No protection IP1 Protected against solid objects up to 50mm (accidental touch by hands) IP2 Protected against solid objects up to 12mm (fingers, knuckles) IP3 IP10 IP11 IP12 IP20 IP21 IP22 IP23 Protected against solid objects up to 2.5mm (tools, wires) IP4 IP30 IP31 IP32 IP33 IP34 IP40 IP41 IP42 IP43 IP44 Protected against solid objects up to 1mm (wires) IP5 IP50 IP53 IP54 IP55 IP56 7 Protected against dust (limited engress permitted) IP6 IP60 IP65 IP66 IP67 Totally protected against dust 20 Discount Schedule B-6

21 Technical Information Ratings Definitions NEMA / U Type Definitions NEMA / U Type Indoor Use Outdoor Use Indoor or Outdoor Use For a degree of protection against: R 3 4 4X 6P 6 Incidental contact with enclosed equipment Falling dirt Rust Circulating dust, lint, fibers and flyings Windblown dust Falling liquids and light splashing Rain (limited water allowed inside) Rain (no water allowed inside) Snow and sleet Hosedown and splashing water Occasional prolonged submersion Oil or coolant spraying or splashing Corrosive agents Occasional temporary submersion 7 Discount Schedule B-6 21

22 Dimensions Series 7 Motor E7 Front Mount (3 Pole) with Screw Fixing Handle Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. Switch Handle Type P Q FS2-A x 48 FS2-E x 48 FS2-I x 48 FS x 48 FS2-S x 62 FS2-A x 64 FS2-E x 64 FS2-I x 64 FS x 64 FS2-S x 78 FS7-G x 54 FS7-N x 54 FS2-G x 67 FS2-N x 67 FS2-A x 88 FS2-I x 88 FS2-G x 88 FS2-N x 88 Switch Body Type B1 B2 F H E E7-25/ E7-40/ E7-80/ E7 Front Mount (6 Pole) with Screw Fixing Handle Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. 7 Switch Handle Type P Q FS2-A x 48 FS2-E x 48 FS2-I x 48 FS x 48 FS2-S x 62 FS2-A x 64 FS2-E x 64 FS2-I x 64 FS x 64 FS2-S x 78 FS7-G x 54 FS7-N x 54 FS2-G x 67 FS2-N x 67 FS2-A x 88 FS2-I x 88 FS2-G x 88 FS2-N x 88 Switch Body Type B1 B2 F G H E E7-25/ E7-40/ E7-80/ Discount Schedule B-6

23 Dimensions Series 7 Motor E7 Front Mount (3 Pole) with Central Nut Fixing Handle Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. Switch Handle Type P Q FC2-A x 48 FC2-E x 48 FC2-I x 48 FC x 48 FC2-G x 67 FC2-N x 67 Switch Body Type E E7-25/ E7-40/ A7 Base Mount (3 Pole) with Screw Fixing Handle Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. Switch Handle Type P Q B FS2-A x FS2-E x FS2-I x FS x FS2-S x FS2-A x (36) FS2-E x (36) FS2-I x (36) FS x (36) FS2-S x (36) ød3 7 FS7-G x FS7-N x FS2-G x (36) FS2-N x (36) FS2-A x FS2-I x FS2-G x FS2-N x Proximity to Hinge Type Y min. X Y max. X E E7-25/ E7-40/ E7-80/ Switch Body Type D3 E F F3 G H A A7-25/ A7-40/ A7-80/ Discount Schedule B-6 23

24 Dimensions Series 7 Motor A7 Base Mount (6 Pole) with Screw Fixing Handle Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. ød3 Switch Handle Type P Q B FS2-A x FS2-E x FS2-I x FS x FS2-S x FS2-A x (36) FS2-E x (36) FS2-I x (36) FS x (36) FS2-S x (36) FS7-G x FS7-N x FS2-G x (36) FS2-N x (36) FS2-A x FS2-I x FS2-G x FS2-N x Proximity to Hinge Type Y min. X Y max. X E E7-25/ E7-40/ E7-80/ Type Q and Emergency Off Switch Switch Body Type D3 E F1 F2 F3 G H A xx A7-25/ A7-40/ A7-80/ HS4 (Type R) Switch Handle Assembly ON 76.2 mm O F F mm 25 7 Type P 50 A7-25(32)-1753-Q 20 A7-25(32)-1753-R Ø 35 Ø 5.5mm Discount Schedule B-6

25 Dimensions Series 7 Motor 7 with Auxiliary Contact Blocks Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. Contacts M 1 N.O. + 1 N.C. 9 2 N.O. + 2 N.C with Ground, Neutral and Fourth Pole Type M / / / Metal Shaft Extension (A2-G3393[4]) Switch Body Type A A7-20/32 59 A7-40/63 73 A7-80/ Shaft Type A A2-G A2-G Discount Schedule B-6 25

26 Dimensions Series 7 Enclosed Motor 7 Enclosed Motor Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. 3/8 (9.7) 7-7/8 (200.2) 3/8 (9.7) 7-23/64 (186.9) 7-1/2 (190.5) 6-3/4 (171.5) 9-1/2 8-3/4 (241.3) (222.3) 1-15/64 (31.2) 2.00 (50.8) 4-15/16 (125.5) (4)-5/16 (7.9) DIA MTG. HOES 1-15/64 (31.2) 4.00 (101.6) (4)-5/16 (7.9) DIA 6-15/16 (176.3) MTG. HOES Dimension Code A Dimension Code B 7.31 (185.7) 8.81 (223.8) 6.54 (166.1) 6.88 (174.8) 5.94 (150.9) 7.04 (178.8) 5.16 (131.1) 5.11 (129.8) 7.31 (185.7) 6.54 (166.1) (301.5) 11.1 (281.9) 7 (4) M4 MTG. HOES Dimension Code C (4) M4 MTG. HOES Dimension Code D 26 Discount Schedule B-6

27 Dimensions Series Y7 Enclosed oad Y7 Enclosed oad Switch (and Thermoplastic Enclosures) Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. ød1 ød1 ød2 E B H Enclosure Type ABS Noryl A B ød1 ød2 E F G H Y7-16M 3 poles ➊ ➊ ~ ~ 70 6 poles 7-G G ~ ~ ~ Y7-25/32 3/4 poles A2-G3572 A2-G ~ 86 6 poles 7-G G ~ ~ ~ Y7-40/63 3/4 poles 7-G G ~ ~ ~ poles 7-G G ~ ~ 120 Y7-80/100 3/4 poles 7-G G ~ ~ F A G F A E B ➊ Empty enclosures not available for purchase Discount Schedule B-6 27

28 Motor Series 7 Notes 7 28 Discount Schedule B-6

29 Series 7 Motor (to 315A) Rugged and reliable motor disconnects up to 100HP (@460V) Sprecher + Schuh s larger 7 Motor extend your range of applications up to 315A. These sturdy switches are compact, reliable and the ideal choice for the rigorous demands of motor disconnect switching. Flexible switch choices Two frame sizes provide a range of disconnect switches rated from 125 to 315 amps. Base and panel mount switches are available in both three and four poles. In addition, all switches are available with either box lugs or bolton terminals. Box lugs are typically used in most applications, however, bolt-on terminals may be preferred in this size switch, particularly in applications where vibration could loosen connections. Convenient accessories Base mount 7 switches come standard with a 195mm ( 7-3/4 ) metal shaft that can easily be cut to the correct length. A longer shaft is also available. Accessories including auxiliary contact blocks, ground and neutral terminals snap-on without the use of tools. Terminal covers are also available. and splash-proof to U Type 3, 3R, 12 (IP66). Excellent making and breaking characteristics provide a level of safety that, in many cases, exceeds international standards. International standards and approvals 7 Motor with box lugs are U / cu isted. 7s with bolt-on lugs are UR / cur Recognized. All switches carry the CE Mark and meet both IEC and requirements. They are approved in virtually every international market. Safe and reliable TIP! Manual Switching Devices: Control, oad or Fusible Which is Best For Your Application? Application Data High short circuit withstand capability ensures a minimum probability of contact welding. with box lugs are touch safe to IP20, while all Switch Handle Assemblies are dust IEC947-1 IEC947-3 IEC207 Typical Control Switch Typical oad Break Switch Typical Fusible Switch 7 To learn the basic differences between control, load and disconnect switches and how to apply them, ask your Sprecher + Schuh representative for publication no: Tech-MSD 112mm ( 4 ) 125A 160A 145mm ( 5 3/4 ) 250A 315A 29

30 Motor Series 7 (to 315A) 3 Pole, Front Mounting, Box ugs, 90º Throw (U / cu isted) 1/1 3/2 5/3 2/T1 4/T2 6/T3 ON 1 OFF 90 0 Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price 3 Pole > E E E E Amp Rating I the U/CSA IEC/VDE/BS Ø HP - U/CSA 240V V V Ø HP - U/CSA 120V V Dimension - mm (inches) 108 (4-1/4) - Height 120 (4-47/64) - Height 112 (4-13/32) - Width 145 (5-23/32) - Width 91 (3-19/32) - Depth ➊ 103 (4-1/16) - Depth ➊ 4 Pole, Front Mounting, Box ugs, 90º Throw (U / cu isted) 1/1 3/2 5/3 N 2/T1 4/T2 6/T3 N 7 ON 1 OFF 90 0 Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price 4 Pole > E E E E Amp Rating I the U/CSA IEC/VDE/BS Ø HP - U/CSA 240V V V Ø HP - U/CSA 120V V Dimension - mm (inches) ➊ (D) Dimension without shaft. 108 (4-1/4) - Height 108 (4-1/4) - Height 150 (5-29/32) - Width (7-51/64) - Width 91 (3-19/32) - Depth ➊ 103 (4-1/16) - Depth ➊ 30

31 Motor Series 7 (to 315A) 3 Pole, Front Mounting, Bolt-on Wiring, 90º Throw (UR / cur Recognized) 1/1 3/2 5/3 2/T1 4/T2 6/T3 ON 1 OFF 90 0 Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price 3 Pole > F F F F Amp Rating I the U/CSA IEC/VDE/BS Ø HP - U/CSA 240V V V Ø HP - U/CSA 120V V Dimension - mm (inches) 110 (4-21/64) - Height 126 (4-31/32) - Height 112 (4-13/32) - Width 145 (6-19/64) - Width 91 (3-19/32) - Depth ➊ 103 (4-1/16) - Depth ➊ 4 Pole, Front Mounting, Bolt-on Wiring, 90º Throw (UR / cur Recognized) 1/1 3/2 5/3 N 2/T1 4/T2 6/T3 N ON 1 OFF 90 0 Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price 4 Pole > F F F F Amp Rating I the U/CSA IEC/VDE/BS Ø HP - U/CSA 240V V V Ø HP - U/CSA 120V V Dimension - mm (inches) 110 (4-21/64) - Height 126 (4-31/32) - Height (7-1/64) - Width 205 (8-3/32) - Width 91 (3-19/32) - Depth ➊ 103 (4-1/16) - Depth ➊ ➊ (D) dimension without shaft. Overall (H) dimension from edge of connectors. 7 31

32 Motor Series 7 (to 315A) 3 Pole, Base Mounting, Box ugs, 90º Throw (U / cu isted) 1/1 3/2 5/3 195mm ( 7-3/4 ) aluminum shaft with door clutch included with all base mount switches. onger shaft available, see Accessories. 2/T1 4/T2 6/T3 ON 1 OFF 90 0 Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price 3 Pole > A A A A Amp Rating I the U/CSA IEC/VDE/BS Ø HP - U/CSA 240V V V Ø HP - U/CSA 120V V Dimension - mm (inches) 108 (4-1/4) - Height 126 (4-31/32) - Height 112 (4-13/32) - Width 145 (5-23/32) - Width 91 (3-19/32) - Depth ➊ 98 (3-55/64) - Depth ➊ 4 Pole, Base Mounting, Box ugs, 90º Throw (U / cu isted) 1/1 3/2 5/3 N 195mm ( 7-3/4 ) aluminum shaft with door clutch included with all base mount switches. onger shaft available, see Accessories. 2/T1 4/T2 6/T3 N 7 ON 1 OFF 90 0 Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price 4 Pole > A A A A Amp Rating I the U/CSA IEC/VDE/BS Ø HP - U/CSA 240V V V Ø HP - U/CSA 120V V Dimension - mm (inches) ➊ (D) Dimension without shaft. 108 (4-1/4) - Height 108 (4-1/4) - Height 150 (5-29/32) - Width (7-51/64) - Width 91 (3-19/32) - Depth ➊ 103 (4-1/16) - Depth ➊ 32

33 Motor Series 7 (to 315A) 3 Pole, Base Mounting, Bolt-on Wiring, 90º Throw (UR / cur Recognized) 1/1 3/2 5/3 195mm ( 7-3/4 ) aluminum shaft with door clutch included with all base mount switches. onger shaft available, see Accessories. 2/T1 4/T2 6/T3 ON 1 OFF 90 0 Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price 3 Pole > B B B B Amp Rating I the U/CSA IEC/VDE/BS Ø HP - U/CSA 240V V V Ø HP - U/CSA 120V V Dimension - mm (inches) 120 (4-47/64) - Height 126 (4-31/32) - Height 112 (4-13/32) - Width 145 (5-23/32) - Width 91 (3-19/32) - Depth ➊ 98 (3-55/64) - Depth ➊ 4 Pole, Base Mounting, Bolt-on Wiring, 90º Throw (UR / cur Recognized) 1/1 3/2 5/3 N 195mm ( 7-3/4 ) aluminum shaft with door clutch included with all base mount switches. onger shaft available, see Accessories. 2/T1 4/T2 6/T3 N ON 1 OFF 90 0 Catalog Number Price Catalog Number Price Catalog Number Price Catalog Number Price 4 Pole > B B B B Amp Rating I the U/CSA IEC/VDE/BS Ø HP - U/CSA 240V V V Ø HP - U/CSA 120V V Dimension - mm (inches) 120 (4-47/64) - Height 126 (4-31/32) - Height 150 (5-29/32) - Width (7-51/64) - Width 91 (3-19/32) - Depth ➊ 98 (3-55/64) - Depth ➊ ➊ (D) dimension without shaft. Overall (H) dimension from edge of connectors. 7 33

34 Motor Series 7 (to 315A) Switch Handle Assemblies Switch Handle Assembly ➊ Protection Rating Color Mounting Method For use with... Frame Size egend Catalog Number Price Type A IP66 Type 3, 3R, 12 Silver egend Black Knob Screw Fixing ➊ x A 88 x 88 x A 130 x 130 O OFF O OFF I ON I ON FS7-A FS7-A Type I IP66 Type 3, 3R, 12 Yellow egend Red Knob Screw Fixing ➊ x A 88 x 88 x A 130 x 130 O OFF O OFF I ON I ON FS7-I FS7-I Type G IP66 Type 3, 3R, 12 Gray Frame Black Knob Screw Fixing ➊ x A 90 x 90 x A 135 x 135 O OFF O OFF I ON I ON FS7-G FS7-G Type N IP66 Type 3, 3R, 12 Yellow Frame Red Knob Screw Fixing ➊ x A 90 x 90 x A 135 x 135 O OFF O OFF I ON I ON FS7-N FS7-N ➊ Mounting screws included with Switch Body Assembly. 34

35 Motor Series 7 (to 315A) Auxiliary Contact Blocks Aux. Contact Block Contact Configuration For use with... Catalog Number Price One NC - Two NO (Early Break) 2353 A B AB-P A B AB-P E F EF-P E F EF-P Switch Accessories Accessory Description Cat. Number Price ong Shaft - 40cm (15-3/4 ) For A7/B AB40 30 Ground & Neutral Terminals Aux. Contact Block Contact Configuration For use with... Catalog Number Price One NC - Two NO (Early Break) A E AE160-PE 236 PE A E AE315-PE 394 B F BF160-PE 236 PE B7-250 F BF250-PE 394 B7-315 F BF315-PE 394 Neutral Terminal A E AE160-TN 236 N A E AE315-TN 394 B F BF160-TN 236 N B7-250 F BF250-TN 394 B7-315 F BF315-TN per package Terminal Covers - two covers required per pole For A/E AE125-C1 24 For A7/E AE250-C1 38 For B7/F AE125-C1 24 For B7/F AE250-C1 38 Nameplate & Frame - Attaches to top or side of all x7 Switch Handles (19.2mm x 49mm) Gray & Black ➊ Blank 2-G MAIN SWITCH 2-G3515A HAUPTSCHATER 2-G3515B INTERR. PRINCIPAE 2-G3515C INTERR. PRINCIPAUX 2-G3515D 15 INTERR. PRINCIPA 2-G3515E HUVUDBRYTARE 2-G3515F WAHSCHATER 2-G3515G Red & Yellow EMERGENCY OFF 2-G3515H 21 7 ➊ Use Discount Schedule B-4 35

36 Technical Information 7 Motor (to 315A) Technical Information IEC Performance Data 125A 160A 250A 315A Rated insulation voltage U i ➊ [V] Rated impulse withstand voltage U imp [kv] Test voltage U i 1 minute [kv] Rated voltage U e ➊➋ [V] Rated Frequency [Hz] 50/60 50/60 50/60 50/60 Conventional free air thermal current I th [A] Conventional enclosed thermal current I the [A] Rated Current I e ➊ AC-1 Non-inductive or only slightly inductive loads 690V [A] AC-21A Switching of resistive loads with slight overload Rated Power P e 7 AC-23A Occasional switching of 3Ø 230V [kw] motors and other highly 400V [kw] inductive loads (criterion for 690V [kw] selecting main switches) AC-3 Squirrel cage motors; 230V [kw] starting and stopping of 400V [kw] running motors 690V [kw] Short circuit current (Type 2 coordination) -Rated conditional short circuit current 400/415V [ka] Maximum fuse rating of circuit (type g, G) [A] Rated short-time current 1cw, 1s [A] Rated breaking capacity AC23A 230V [A] (cosϕ 0.45) 400V [A] V [A] DC switching capacity Rated current I e 3 poles 60V [A] in series 110V [A] DC-21A - For resistive loads, 220V [A] T< 1 ms 4 poles 110V [A] U e max. = 600V in series 220V [A] V [A] Rated power P e 24V [kw] poles 48V [kw] DC-22A, DC-3 in series 60V [kw] For inductive loads, T 2.5 ms 110V [kw] V [kw] Rated power P e 24V [kw] poles 48V [kw] DC-23A, DC-5 in series 60V [kw] For inductive loads, T 15 ms 110V [kw] V [kw] ➊ Valid for line with grounded common neutral termination, overvoltage category III, pollution degree 3. Other values on request. ➋ Not suitable for load switching applications (AC-20) above 690V. 36

37 Technical Information 7 Motor (to 315A) Technical Information (continued) U/CSA Data 125A 160A 250A 315A Rated insulation voltage [V] Rated voltage [V] Continuous current [A] Amp rating for general use [A] Motor Rating 60Hz 120V [FA] [HP] V [FA] Single phase, 2 poles [HP] V [FA] [HP] V [FA] [HP] V [FA] [HP] V [FA] Three phase [HP] V [FA] [HP] V [FA] [HP] Mechanical Data Protection class according to IEC A 160A 250A 315A Motor rating 60 Hz Switch Handles IP66 IP66 IP66 IP66 Box lugs IP20 IP20 IP20 IP20 Bolt-on IP20 IP20 IP20 IP20 Mechanical life [millions of operations] Operating Torque (max.) [Nm] Pole ON [bf.-in.] Pole OFF [Nm] [bf.-in.] Pole ON [Nm] [bf.-in.] Pole OFF [Nm] [bf.-in.] Temperature Range operation [ C] (+23 F +104 F) storage [ C] / max. 70 C for 24 hr. ( 13 F +131 F / max.+158 F for 24 hr.) Maximum wire gauges Terminal size per IEC Gauge No. B11 B11 B14 B14 Fine strands, 1 conductor Max. [mm 2 ] Min. [mm 2 ] Rigid wire, 1 conductor Max. [mm 2 ] Min. [mm 2 ] Wire gauges according to U/CSA Max. [AWG] 3 / 0 3 / 0 ~ [MCM] ~ ~ Min. [AWG]

38 Technical Information 7 Motor (to 315A) Approvals Catalog No. or Designation U isted (marked with U) UR Recognized (marked with UR) U isted for Canada (marked with cu) UR Recognized for Canada (marked with cur) A7-125 E7-125 A A A A7-160 E7-160 A A A A7-250 E7-250 A A A A7-315 E7-315 A A A B7-125 F7-125 A A A B7-160 F7-160 A A A B7-250 F7-250 A A A B7-315 F7-315 A A A Auxiliary Switch Blocks Z Z Z Z Z Ground Terminal Z Z Z Z Z Neutral Terminal Z Z Z Z Z CE 7 A = Approved or test passed Z = Accessories are covered by the approval for the switch 37.1

39 Dimensions 7 Motor (to 315A) Exploded Views A quarter-turn of the built-in mounting nut on the face of the switch secures the shaft A7 (B7) Base Mount Switch comes standard with one 195mm ( 7-3/4 ) aluminum shaft, door clutch, and a back-of-panel interlock for mating with the door clutch. The shaft is cut to length in the field. A longer shaft 40cm ( 15-3/4 ) is also available. The Switch Handle Assembly comes with all front-of-panel components, including mounting screws. A (B) Switch Bodies pages 32 & 33 Switch Handle Assemblies page 34 E7 (F7) Front Mount Switch comes standard with an integral shaft which mates with the Switch Handle Assembly in the field. Panel mounting screws are also included. The Switch Handle Assembly comes with all front-of-panel components, including mounting screws. Switch Handle Assemblies page 34 7 E (F) Switch Bodies pages 30 & 31 38

40 Dimensions 7 Motor (to 315A) E7 Front Mount with Box ugs (3 & 4 Pole) Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. max. E 2 mm I A F G H B C D 125A 91 (3-19/32) 160A 91 (3-19/32) 250A 103 (4-3/64) 315A 103 (4-3/64) A B C D E F G H I 112 (4-13/32) 112 (4-13/32) 145 (5-23/32) 145 (5-23/32) 36 (1-13/32) 36 (1-13/32) 44 (1-23/32) 44 (1-23/32) 38 (1-1/2) 38 (1-1/2) 52.5 (2-1/16) 52.5 (2-1/16) 95 (3-23/64) 95 (3-23/64) 185 (7-9/32) 185 (7-9/32) 88 (3-7/16) 88 (3-7/16) 88 (3-7/16) 88 (3-7/16) 68 (2-5/8) 68 (2-5/8) 68 (2-5/8) 68 (2-5/8) 108 (4-1/4) 108 (4-1/4) 120 (4-11/16) 120 (4-11/16) M5 (3/16) M5 (3/16) M5 (3/16) M5 (3/16) F7 Front Mount with Bolt-on Terminals (3 & 4 Pole) Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. O F G P A D H I N M E B C 125A 91 (3-19/32) 160A 91 (3-19/32) 250A 103 (4-3/64) 315A 103 (4-3/64) A B C D E F G H I M N O P 112 (4-13/32) 112 (4-13/32) 145 (5-23/32) 145 (5-23/32) 38 (1-1/2) 38 (1-1/2) 52.5 (1-22/32) 52.5 (1-22/32) 65.5 (2-9/16) 65.5 (2-9/16) 60.4 (2-3/8) 60.4 (2-3/8) 3 (1/8) 3 (1/8) 4 (5/32) 4 (5/32) 2 (3/32) 2 (3/32) 2 (3/32) 2 (3/32) 36 (1-13/32) 36 (1-13/32) 44 (1-23/32) 44 (1-23/32) 88 (3-7/16) 88 (3-7/16) 88 (3-7/16) 88 (3-7/16) 68 (2-5/8) 68 (2-5/8) 68 (2-5/8) 68 (2-5/8) 10 (13/32) 10 (13/32) 13 (1/2) 13 (1/2) 90 (3-17/32) 90 (3-17/32) 100 (3-15/16) 100 (3-15/16) 64 (2-17/32) 64 (2-17/32) 70 (2-3/4) 70 (2-3/4) M5 (3/16) M5 (3/16) M5 (3/16) M5 (3/16) M10 (3/8) M10 (3/8) M12 (15/32) M12 (15/32) 7 39

41 Dimensions 7 Motor (to 315A) A7 Base Mount with Box ugs (3 & 4 Pole) Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. E max. D 2 mm A F H I B C E G 125A 91 (3-19/32) 160A 91 ((3-19/32) 250A 98 (3-27/32) 315A 98 (3-27/32) A B C D E F G H I 112 (4-13/32) 112 (4-13/32) 145 (5-23/32) 145 (5-23/32) 38 (1-1/2) 38 (1-1/2) 52.5 (1-23/32) 52.5 (1-23/32) 95 (3-23/64) 95 (3-23/64) 185 (7-9/32) 185 (7-9/32) 2 (3/32) 2 (3/32) 2 (3/32) 2 (3/32) 118 (4-5/8) 118 (4-5/8) 140 (5-1/2) 140 (5-1/2) 6.4 (1/4) 6.4 (1/4) 6.4 (1/4) 6.4 (1/4) 108 (4-1/4) 108 (4-1/4) 126 (4-15/16) 126 (4-15/16) 64 (2-17/32) 64 (2-17/32) 70 (2-3/4) 70 (2-3/4) 36 (1-13/32) 36 (1-13/32) 44 (2-1/16) 44 (2-1/16) B7 Base Mount with Bolt-on Terminals (3 & 4 Pole) 7 A 125A 91 (3-19/32) 160A 91 ((3-19/32) 250A 98 (3-27/64) 315A 98 (3-27/64) A B C D E F G H I M N O P Q 112 (4-13/32) 112 (4-13/32) 145 (5-23/32) 145 (5-23/32) B 38 (1-1/2) 38 (1-1/2) 52.5 (1-23/32) 52.5 (1-23/32) 35.5 (1-7/16) 35.5 (1-7/16) 38.6 (1-1/2) 38.6 (1-1/2) 3 (1/8) 3 (1/8) 4 (5/32) 4 (5/32) C 2 (3/32) 2 (3/32) 2 (3/32) 2 (3/32) E D 76 (3) 76 (3) 80 (3-1/8) 80 (3-1/8) F G F 36 (1-13/32) 36 (1-13/32) 44 (1-23/32) 44 (1-23/32) Q 20 (3/4) 20 (3/4) 26 (1-1/64) 26 (1-1/64) H 90 (3-17/32) 90 (3-17/32) 100 (3-15/16) 100 (3-15/16) P 64 (2-17/32) 64 (2-17/32) 70 (2-3/4) 70 (2-3/4) I O 10 (13/32) 10 (13/32) 13 (1/2) 13 (1/2) M10 (3/8) M10 (3/8) M12 (15/32) M12 (15/32) N M 36 (1-13/32) 36 (1-13/32) 44 (1-23/32) 44 (1-23/32) 6.4 (1/4) 6.4 (1/4) 6.4 (1/4) 6.4 (1/4) 40

42 Dimensions 7 Motor (to 315A) Box ug Ground and Neutral Terminal Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. FRONT BASE B E A C D F 125 / 160A 37.8 (1-1/2) 250 / 315A 52.3 (2-1/16) A B C D E F 64 (2-17/32) 71.1 (2-25/32) 108 (4-1/4) 126 (4-15/16) 37.8 (1-1/2) 52.3 (2-1/16) 64 (2-17/32) 80.6 (3-1/8) 108 (4-1/4) 126 (4-15/16) Bolt-on Ground and Neutral Terminal FRONT BASE D F B H N A C E G I M 125 / 160A 37.8 (1-1/2) 250 / 315A 52.3 (2-1/16) A B C D E F G H I M N 64 (2-17/32) 68 (2-21/32) 10 (13/32) 13 (1/2) M10 (13/32) M12 (15/32) 90 (3-17/32) 100 (3-15/16) 3 (1/8) 4 (5/32) 37.8 (1-1/2) 52.3 (2-1/16) Auxiliary Contacts 64 (2-17/32) 68 (2-21/32) 10 (13/32) 13 (1/2) M10 (13/32) M12 (15/32) 90 (3-17/32) 100 (3-15/16) 3 (1/8) 4 (5/32) FRONT BASE

43 Dimensions 7 Motor (to 315A) Terminal Cover Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. A 125 / 160A 76.2 (3) 250 / 315A 88 (3-15/32) B 95 (3-3/4) (4-5/16) A B Door Clutches 5.4 mm 68 7 Ø for Standard Shaft mm (3-21/ /32 ) Shaft must be cut to length at installation. 42

44 Dimensions 7 Motor (to 315A) Switch Handle Assemblies (Types A, I, G & N small) Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. 1-4 mm 1-4 mm 68 Ø Switch Handle Assemblies (Types A, I, G & N large) 88 x x Ø mm 1-4 mm 68 Ø x x 135 Ø Additional Name Plate Frame and legend snap on to Switch Handle Assembly frame. Fits all Switch Handle Assemblies. 84 G

45 Motor Series 7 (to 315A) Notes 7 44

46 Series 10 Fusible & Non-fusible Sprecher + Schuh s 10 series of fused and non-fused disconnect switches comply with service entrance requirements. This family of rod operated switches is suitable for applications that require small panel space and superior short circuit protection. Suitable as a Service Entrance ing Means TIP! Manual Switching Devices: Control, oad or Fusible Which is Best For Your Application? Application Data Typical Control Switch Typical oad Break Switch Typical Fusible Switch Big performance in a small package 10 disconnects are rated to 400A and can be operated at up to 600V. They protect motors up to 250HP (@460V). The 10 may be installed on circuits capable of delivering up to 100,000A of short circuit fault current; levels typically found in modern industrial facilities. This performance comes in a small package, leaving room for additional branch circuit components within the panel. Maximum protection for downstream equipment 10 switches are engineered to provide excellent short-circuit protection for downstream equipment. These switches accept the latest small-dimension HRCI-J and HRCII-C fuses. This Type 2 protection limits let-through currents to levels specified for IEC equipment, and ensures that when the short circuit is cleared, the device will be operable. Meets the toughest safety standards The 10 series is suitable for use in service entrance applications. Further insuring safety, line-side terminal shields are standard on all 10 disconnects. Non-fused switches (30 & 60A) feature dead-front construction while fuse covers are available for all devices, preventing contact with live parts. Common parts reduce inventory Universal auxiliary contact blocks fit on all frame sizes, reducing inventory. In addition, all 30 and 60A switches use the same operating handles and shafts, ditto for the 100, 200 and 400A frame sizes. On-board fuse carriers also eliminate the need for extra components while reducing panel space requirements. Comprehensive standards and approvals 10 disconnect switches conform to U 98 standards ( A switches) and U1087/489 standards (30 & 60A switches); are U isted, CSA, ASTA and OVAG Certified and are designed to meet IEC 947-3, VDE, DIN, BS and applicable NEMA requirements. 10 To learn the basic differences between control, load and fusible disconnect switches and how to apply them, ask your Sprecher + Schuh representative for publication no: Tech-MSD Up to four auxiliary contact blocks can be fitted on each 10 disconnect switch 45

47 Series 10 U/CSA Fused Amp Rating 1 Ø (60Hz) Maximum Horsepower ➊ Three Phase (60Hz) DC Switch (typical) (A) 120V 240V 200V 240V 460V 600V 125V 250V Catalog Number Price U Class J and CSA HRCI-J Fuses ➋ Dimension Code NJ030P3 362 A NJ060P3 471 B1 100 ~ 7.5 ~ ~ NJ100P3 744 C1 200 ~ 10 ~ ~ NJ200P D1 400 ~ ~ ~ NJ400P F1 CSA HRCII-C Fuses ~ ~ 10-NA200P3 362 A ~ ~ 10-NA300P3 471 B1 100 ~ ~ ~ 10-NH100P3 744 D1 200 ~ ~ ~ 10-NH200P E1 400 ~ ~ ~ 10-NH400P F1 U/CSA Non-Fused ➌ Amp Rating 1 Ø (60Hz) Maximum Horsepower ➊ Three Phase (60Hz) DC Switch (typical) (A) 120V 240V 200V 240V 460V 600V 125V 250V Catalog Number Price Dimension Code NN030P3 305 A NN060P3 414 B2 100 ~ 7.5 ~ ~ NN100P3 744 C1 200 ~ 10 ~ ~ NN200P D1 10 Note: 10 Fusible and Non-fusible with dimension codes D, E & F require lugs. Sprecher + Schuh lugs available on page ~ ~ ~ NN400P F1 Ordering Instructions Specify Switch catalog number (page 46) Specify desired switch handle catalog number (page 47) Specify desired operating shaft catalog number (page 48) Specify desired accessories (page 49) ➊ Time delay fuses may be required to utilize the disconnect switch at its maximum horsepower rating. ➋ Only U listed Class J and CSA Certified HRCI-J fuses are suitable for use with these disconnect switches. ➌ Non-fused disconnect switches must use separately installed U isted Class J, CC or T fuses or CSA Certified HRCI-J fuses. 46

48 Series 10 Switch Handle Assemblies Switch Handle Assembly ➊ Description Color Degree of Protection Catalog Number Price 76 x 76mm Type R Handle with defeater Type R Handle - For 30A and 60A switches - With Defeater - ockable: 3 locks ➋ Black Red/Yellow Type 1 IP42 10-HS1 36 Type 3R, 3, 12, 4, 4X IP66 10-HS4 56 Type 1 IP42 10-HS1E 36 Type 3R, 3, 12, 4, 4X IP66 10-HS4E x 76mm Type R Handle without defeater Type R Handle - For 30A and 60A switches - Without Defeater - ockable: 3 locks ➋ Black Red/Yellow Type 1 IP42 10-HS1-N2 68 Type 3R, 3, 12, 4, 4X IP66 10-HS4-N2 56 Type 1 IP42 10-HS1E-N2 68 Type 3R, 3, 12, 4, 4X IP66 10-HS4E-N X 103mm Pistol Grip Handle with defeater Pistol Grip Handle - For 100A, 200A and 400A switches ➌ - With Defeater - ockable: 3 locks ➋ Black Red/Yellow Type 1 IP42 10-HM1 68 Type 3R, 3, 12, 4, 4X IP66 10-HM4 104 Type 1 IP42 10-HM1E 68 Type 3R, 3, 12, 4, 4X IP66 10-HM4E X 103mm Pistol Grip Handle without defeater Pistol Grip Handle - For 100A, 200A and 400A switches ➌ - Without Defeater - ockable: 3 locks ➋ Black Red/Yellow Type 1 IP42 10-HM1-N2 68 Type 3R, 3, 12, 4, 4X IP66 10-HM4-N2 104 Type 1 IP42 10-HM1E-N2 68 Type 3R, 3, 12, 4, 4X IP66 10-HM4E-N ➊ Mounting screws included with Switch Handle Assembly. ➋ ockable in OFF position (and ON position with special modification). ➌ Can be used on 30 and 60A switches. Select 10-R1M or 10-R2M shaft. 47

49 Series 10 Metal Operating Shafts Shaft (typical) Switch Dimension Code For use with handle type Operating Shaft ength (mm) Catalog Number Price A1, A2 B1, B2 Type R (10-30/60A) R R A1, A2 B1, B2 Pistol Grip (10-30/60A) R1M R2M C1, D1 Pistol Grip (10-100/200A) R R E1, F1 Pistol Grip (10-NH200/400A) R R Operating Shaft Accessories Accessory Description Catalog Number Price Shaft Guide - Increases the alignment tolerance of the shaft to the switch handle. For 10-R1(2) shafts 10-HSG Accessories Accessory Description Catalog Number Price Auxiliary Contact Blocks - One pole (NO) One pole (NC) Two pole (1 NO/1 NC) Two pole (NO) Two pole (NC) Auxiliary Contact Adaptor - Required for fitting auxiliary contacts to all 30 & 60A fused and non-fused disconnect switches. One required. 10-GA10 ➊➋ 10-GA01 ➊➋ 10-GA11 ➊➋ 10-GA20 ➊➋ 10-GA02 ➊➋ AA Auxiliary Contact Support Kit - Required when mounting more than two Auxiliary Contact Blocks per switch. 10-A ➊ 30 & 60A disconnect switches require Auxiliary Contact Adaptor (10-AA) for installation of auxiliary contacts. ➋ A maximum of four contact blocks can be installed on each disconnect switch. When more than two contact blocks are used, the Auxiliary Contact Support Kit (10-A1) must be installed. 48

50 Series 10 Accessories (Continued) Accessory Description Catalog Number Price Padlocking Kit - For 30 & 60A switches 10-P Switch Handle Instruction abel - For use with all Switch Handle Assemblies (10 per package - priced per package) Fuse Covers ➊ - Dim. Code A1, A2 B1, B2 C1 D1 E1 F1 Quantity Req d Terminal Shield ➋ - All come standard with one Terminal Shield. For use on either line or load side of the disconnect switch. Dim. Code A1, A2 B1, B2 C1 D1 E1 F1 Terminal ugs - 3 per package Dimension Code D1 (10-NH100P3 only) Wire Size 10mm 2 50mm 2 #8 1/0 AWG 10-FCA2 ➋ 10-FCJ60 ➋ 10-FCC1 10-FCD1 10-FCE1 10-FCF1 10-NC1 ➋ 10-NC2 ➋ 10-NC3 10-NC4 10-NC5 10-NC6 10-E D1 16mm 2 120mm 2 #6 250MCM AWG 10-F E1 25mm 2 240mm 2 #4 500MCM AWG 10-G F1 Two 50mm 2 150mm 2 Two 1/0 350MCM AWG 10-H ➊ Also used for covering the shorting bars on 100, 200 and 400A Non-fused switches. ➋ Non-fused disconnects include dead front cover and fuse covers for fusible disconnects. Also includes extra terminal shield. Applies to 30A and 60A versions only. 49

51 Series Enclosed Motor s (U and CSA Approved Enclosures) Type 3/4/12 Watertight, Dusttight Sheetmetal Enclosure - IP66 Type 4/4X Watertight, Corrosion-Resistant Stainless Steel Enclosure - IP66 Type 4/4X Watertight, Corrosion-Resistant Non-metallic Enclosure - IP66 Amp/Horsepower Rating U/ CSA Amps 1Ø (60 Hz) Horsepower 3Ø (60 Hz) 120V 240V 200V 240V 460V 600V Catalog Number Price Catalog Number Price Catalog Number Price NOTE: All Enclosed s come standard with a black handle with ON/OFF marking. For a yellow and red handle, add suffix E to the end of the catalog number. Example: change 10- FN030P3 to 10-FN030P3E. Dimension Code Non-Fused FN030P3 561 A2 10-CN030P A2 10-KN030P3 561 A FN060P3 993 B2 10-CN060P B2 10-KN060P3 993 B2 100 ~ 7.5 ~ FN100P C1 10-CN100P C1 10-KN100P C1 200 ~ 10 ~ FN200P D1 10-CN200P D1 10-KN200P D1 400 ~ ~ FN400P F1 10-CN400P F1 10-KN400P F1 Class J Fused FJ030P3 847 A1 10-CJ030P A1 10-KJ030P3 850 A FJ060P B1 10-CJ060P B1 10-KJ060P B1 100 ~ 7.5 ~ FJ100P C1 10-CJ100P C1 10-KJ100P C1 200 ~ 10 ~ FJ200P D1 10-CJ200P D1 10-KJ200P D1 400 ~ ~ FJ400P F1 10-CJ400P F1 10-KJ400P F1 Dimension Code Dimension Code 10 50