ATyS S - ATyS d S Remotely operated Transfer Switching Equipment from 40 to 125 A

Size: px

Start display at page:

Download "ATyS S - ATyS d S Remotely operated Transfer Switching Equipment from 40 to 125 A"

Bathsheba Watts
5 years ago
Views:

Transfer switches The solution for > Genset < 90 kva > Heating systems > Climate control > Ventilation systems > Telecommunications atys-s_018_a Strong points Function products are 4 pole remotely

They enable the on-load transfer of two three-phase supplies via remote volt-free contacts, from either an external automatic controller, using pulse logic, or a switch.

Advantages Extensive power supply range The is available in four supply versions, each with a broad range (+/-30%). The four versions are: 12 VDC power supply. 24/48 VDC power supply.

In addition, they do not require a power supply to maintain position, thus protecting their loads from voltage fluctuations.

1 Transfer switches The solution for > Genset < 90 kva > Heating systems > Climate control > Ventilation systems > Telecommunications atys-s_018_a Strong points Function products are 4 pole remotely operated transfer switches with positive break indication. They enable the on-load transfer of two three-phase supplies via remote volt-free contacts, from either an external automatic controller, using pulse logic, or a switch. They are intended for use in low voltage power supply systems where a brief interruption of the load supply is acceptable during transfer. Advantages Extensive power supply range The is available in four supply versions, each with a broad range (+/-30%). The four versions are: 12 VDC power supply. 24/48 VDC power supply. 230 VAC single power supply. 2 x 230 VAC dual power supply. Safety and reliability products use stable position technology, ensuring constant pressure on the contacts and preventing premature faults. In addition, they do not require a power supply to maintain position, thus protecting their loads from voltage fluctuations. Simplified maintenance Maintenance can be carried out easily under load, with manual operation still available. The control and motorisation section can be replaced simply by removing 4 screws, with no work required on the installation cabling. ATyS d S: Dual power supply In addition to the functions offered by the, the ATyS d S incorporates supply redundancy without the need for additional wiring. This is obtained by integrating a double supply (2 independent supplies) directly within the product. > Extensive power supply range > Safety and reliability > Easy integration > Simplified maintenance > ATyS d S: Dual power supply Conformity to standards > IEC > IEC > GB Approvals and certifications Easy integration products can be easily installed inside enclosures. Their design, and in particular their compact size, enables integration within most 200 mm deep enclosures. 434 General Catalogue

2 s No. of poles Power supply Bridging bars 40 A 63 A 80 A 100 A 125 A 4 P 24/48 VDC P 12 VDC P 230 VAC P 24/48 VDC P 12 VDC P 230 VAC Source side P 24/48 VDC P 4 P 12 VDC Load side 4 P 230 VAC P 24/48 VDC P 12 VDC P 230 VAC P 24/48 VDC P 12 VDC P 230 VAC Terminal shrouds Voltage tap Terminal retainer DIN rail modules ATyS d S No. of poles Power supply ATyS d S Bridging bars 40 A 4 P 2 x 230 VAC A 4 P 2 x 230 VAC A 4 P 2 x 230 VAC A 4 P 2 x 230 VAC A 4 P 2 x 230 VAC P Terminal shrouds Voltage tap Terminal retainer DIN rail Source side Load side modules General Catalogue

Accessories Bridging bars For bridging power terminals on the top or bottom side of the

of poles 40 125 4 P 9509 4013 acces_395_a_2_cat Voltage tap Enables the required power

prevent direct access to the power supply and control terminals and - to secure these

Pack 40 125 9599 4003 atys-s_021_a Terminal shrouds IP2X protection against direct contact

Terminal shrouds for the source side Pack 40 125 9594 4012 atys-s_020_a Terminal shrouds

3 Accessories Bridging bars For bridging power terminals on the top or bottom side of the switch. No. of poles P acces_395_a_2_cat Voltage tap Enables the required power supply for 230 VAC and ATyS d S products to be tapped directly from the product's incoming power terminals. Can also be utilised in applications without neutral, to provide 400 VAC to the autotransformer atys-s_022_a Terminal retainer These clips have a dual function: - to prevent direct access to the power supply and control terminals and - to secure these connector terminals. Pack atys-s_021_a Terminal shrouds IP2X protection against direct contact with terminals or connecting parts. Terminal shrouds for the source side Pack atys-s_020_a Terminal shrouds for the load side Pack atys-s_020_a Autotransformer 400/230 VAC For applications without neutral, this autotransformer provides the 230 VAC required to power these ATyS products. Dimensions 75x80x72 mm DIN rail This 4-module DIN rail can be installed directly on the front of the and can be utilised, for example, for the installation of a surge protection device acces_417_a_1_cat 436 General Catalogue

4 Spares Motorisation unit The motorisation module of the can be easily replaced in case of problems, even when the load is supplied. Switching unit s to be used for replacing the switching module of products. Manual emergency operation handle This handle can be used on the product whether the motor unit is mounted or not. Connector kit 12 VDC 24/48 VDC 230 VAC ATyS d S 2x230 VAC This kit, including all the connector types for the different products, can be ordered in case of loss or breaking of one connector acces_416_a_1_cat poign_058_a_1_x_cat acces_414_a_1_cat acces_415_a_1_cat General Catalogue

5 Enclosed solutions General characteristics and ATyS d S Adapted to mechanical risk and dust hazard. Protection degree: IP3X (IP54 optional) Colour: RAL 7035, epoxy polyester powder. Wall mounting: 4 fixing lugs supplied loose. Connection of cables: top or bottom. Locking system: 3 mm double-bar Lock (key supplied) Power network 230/400 VAC +/-30%, 50/60 Hz. Two power supplies: 12 VDC and 2 x 230 VAC. Manual emergency operation handle provided with the enclosure. Bridging bars provided fitted on the product. coff_418_a s No. of poles 12 VDC ATyS d S 2 x 230 VAC 40 4 P P P P P Accessories Factory fitted Description LEDs indicating if voltage is present LEDs for position indication TESTS/AUTO modes selection (with C30 option) Priority selection (with C30 option) Surge arresters for enclosure (SURGYS D40) Three-phase kit without neutral Kit for auxiliary output (3Ph+N) 16A Copper bar connection kit IP54 kit IPXXB protection screen (door open) Battery charger Kit for voltage sensing on terminals Auxiliary kit for control on terminals Kit for ATyS C30 control/command Customer fit Description Copper bar connection kit IP54 kit IPXXB protection screen (door open) Dimensions Connection crosssection (mm²) H (mm) L (mm) P (mm) Weight (kg) S1 450 S P1 P LOAD coff_423_a_1_cat General Catalogue

Characteristics according to IEC 60947-3 and IEC 60947-6-1 40 to 125 A Thermal current I th at 40 C 40 A 63 A 80 A 100 A 125 A Rated insulation voltage U i (V) (power circuit) 800 800 800 800 800

6 Characteristics according to IEC and IEC to 125 A Thermal current I th at 40 C 40 A 63 A 80 A 100 A 125 A Rated insulation voltage U i (V) (power circuit) Rated impulse withstand voltage U imp (kv) (power circuit) Rated insulation voltage U i (V) (operation circuit) Rated impulse withstand voltage U imp (kv) (operation circuit) Rated operational currents I e (A) according to IEC Rated voltage Utilisation category A/B A/B A/B A/B A/B 415 VAC AC-31 B VAC AC-32 B Rated operational currents I e (A) according to IEC Rated voltage Utilisation category A/B A/B A/B A/B A/B 415 VAC AC-20 A / AC-20 B 40/40 63/63 80/80 100/ / VAC AC-21 A / AC-21 B 40/40 63/63 80/80 100/ / VAC AC-22 A / AC-22 B 40/40 63/63 80/80 100/ / VAC AC-23 A / AC-23 B -/40 -/63 -/63 -/63 -/63 Fuse protected short-circuit withstand (ka rms prospective) Prospective short-circuit current (ka rms) Associated fuse rating (A) Circuit breaker protected short-circuit withstand with any circuit breaker that ensures tripping in less than 0.3s (3) Rated short-time withstand current 0.3s I cw (ka rms) Short-circuit capacity as per IEC Rated short-time withstand current 0.03 s. (ka) Rated short-circuit making capacity l cm (ka peak) Short-circuit capacity as per IEC (without protection) Rated short-time withstand current 1 s. I cw (ka rms) Rated peak withstand current (ka peak) Connection Maximum Cu cable cross-section (mm 2 ) Tightening torque mini / maxi (Nm) 1.2/3 1.2/3 1.2/3 1.2/3 1.2/3 Switching time (Standard setting) I - 0 or II - 0 (ms) I - II or II - I (ms) Duration of "electrical blackout" I - II (ms) minimum Power supply Power supply 12 VDC min / max (VDC) 9/15 9/15 9/15 9/15 9/15 Power supply 24/48 VDC min / max (VDC) 17/62 17/62 17/62 17/62 17/62 Power supply 230 VAC min / max (VAC) 160/ / / / /310 Control supply power demand Power supply 12 VDC inrush / nominal (VA) 200/40 200/40 200/40 200/40 200/40 Power supply 24/48 VDC inrush / nominal (VA) 200/40 200/40 200/40 200/40 200/40 Supply 230 VAC inrush / nominal (VA) 200/40 200/40 200/40 200/40 200/40 Mechanical characteristics Durability (number of operating cycles) Weight and ATyS d S 4 P (kg) (1) Value for coordination with any circuit breaker that ensures tripping in less than 0.3s. For coordination with specific circuit-breaker references, higher short-circuit current values are available. Please consult us. General Catalogue

7 8 - ATyS d S Terminals and connections DC version 1 2 atys_831_b_1_x_cat DC 1 preferred source 2 alternate source 1 : position 0 control 2 : position I control 3 : position II control 4 : auxiliary contact, closed when the switch is in position 0 5 : auxiliary contact, closed when the switch is in position II 6 : auxiliary contact, closed when the switch is in position I 7 : power supply 12 VDC (9-15 VDC) or 24 VDC / 48 VDC (17-62 VDC) depending on the version : 230 VAC 1 2 atys_832_a_1_x_cat preferred source alternate source 1 : position 0 control 2 : position I control 3 : position II control 4 : auxiliary contact, closed when the switch is in position 0 5 : auxiliary contact, closed when the switch is in position II 6 : auxiliary contact, closed when the switch is in position I 7 : power supply kit: 230 VAC ( VAC) ATyS d S: 2 x 230 VAC 1 2 atys_830_a_1_x_cat preferred source alternate source 1 : position 0 control 2 : position I control 3 : position II control 4 : auxiliary contact, closed when the switch is in position 0 5 : auxiliary contact, closed when the switch is in position II 6 : auxiliary contact, closed when the switch is in position I 7 : power supply kit I: 230 VAC ( VAC) 8 : power supply kit II: 230 VAC ( VAC) 440 General Catalogue

8 Dimensions Cut-out dimension M Ø atys-s_024_a_1_x_cat 45 Connection terminal Ø M6 atys-s_036_a_1_x_cat General Catalogue

ATyS d M Remotely operated Transfer Switching Equipment from 40 to 160 A

ATyS d M Remotely operated Transfer Switching Equipment Transfer switches new The solution for > Applications with an external ATS/AMF controller > Building Management Systems (BMS) atys-md_002_b_1_cat