Flow Controls & Accessories

Transcription

1 Flow ontrols & ccessories Section V V Flow ontrol Valves SPF Series Series Series Miniature Right ngle Series...7 FM701 & FM703 Series...8 F701, F702, FS701 Series...9 Needle Valves SPN Series Series...11 SP Series heck Valve & 3047 Series heck Valve...13 EM Series Exhaust Mufflers...14 reather Vents...15 ES Series Silencer...15 SN ir Line Silencer...16 Muffler-Reclassifier ES...17 utomatic Drip Leg Drain & Relief Valve...18 Relief Valve - Diaphragm Type...19 Shuttle Valves & Quick Exhaust Shuttle Valve...22 Parker Hannifin orporation Division

2 atalog 0600P-5/US Flow ontrol Valves Flow ontrols & ccessories SPF Series 1/8" to 1/2" Ports omponent Materials ody Material: rass Needle: Stainless Steel all heck: Stainless Steel heck Retainer: cetal Needle Seals: Nitrile (Standard), Fluorocarbon (Optional) Knob: luminum D E F (Open) (oth Ends) General Information The SPF Series Flow ontrol Valves meter flow of air or oil in one direction and allow free flow in the reverse direction. SPF Series valves are manufactured with a two step needle. Fine metering is accomplished over the initial adjustment turns and nominal metering is provided over the remaining turns. Once the desired flow is selected, a set screw can be tightened to maintain the setting. These valves are available with NPTF ports in 1/8", 1/4", 3/8", and 1/2" sizes PSI Non-Shock racking pressure for return check poppet 5 PSI Nominal Standard: 0 to 140 F* -40 to 140 F (Hydraulic service) Extended Temperature: 0 to 400 F* * mbient temperatures below freezing require moisture-free air. mbient temperatures below freezing and above 180 require lubricants especially selected for suitability at these temperatures. valves should be used with filtered and lubricated air. Model Selection and Dimensions Model Number Port Size D E F SPF200 1/8-27 NPTF SPF400 1/4-18 NPTF SPF600 3/8-18 NPTF SPF800 1/2-14 NPTF For units with Fluorocarbon seals, add suffix V. Example: SPF200V Performance Data - Flow ontrolled Flow Free Flow Needle Full Open/heck losed Needle Full Open Model Flow - SFM Effective Flow - SFM Effective 100 PSI v 100 PSI v rea Full DP Sq. Inches Full DP Sq. Inches SPF SPF SPF SPF Parker Hannifin orporation Division

3 atalog 0600P-5/US Micrometer Flow ontrol Valves Flow ontrols & ccessories 337 Series 1/8" to 3/4" Ports omponent Materials ody Material: rass Needle: Stainless Steel heck Seal: Urethane Needle Seals: una N (Fluorocarbon optional consult factory) Model Selection and Dimensions General Information The 337 Series Flow ontrol Valves meter flow of air in one direction and allow free flow in the reverse direction. The 337 Series valves are manufactured with a fine tapered needle providing precise flow control, even at low flow rates. The perimeter of the adjustment knob features numerical micrometer position markings providing a visual indication of the setting. Once the desired flow is selected, a set screw can be tightened to maintain the setting. These valves are available with NPTF ports in 1/8", 1/4", 3/8", 1/2", and 3/4" sizes. This series is recommended for pneumatic service. 250 PSI racking pressure for return check poppet 1 to 2 PSIG Standard: 0 to 180 F* Extended Temperature: 0 to 300 F* (consult factory) * mbient temperatures below freezing require moisture-free air. mbient temperatures below freezing and above 180 require lubricants especially selected for suitability at these temperatures. valves should be used with filtered and lubricated air. Port Flow (SFM ) Dimensions Service Size Model dj. Free Flow H1 H2 Kit 1/8" /16" /4" /16" /8" /8" /2" /16" /4" /8" t 100 PSIG inlet pressure with full pressure drop. Mounting racket Mounting racket Model Selection and Dimensions Port Size 1 DI H1 - OPEN H2 - LOSED Knob: luminum Spring: Stainless Steel Retainer: Zinc- Plated Steel Set Screw: Steel Mounting Dimensions racket Model No. D E F G 1/8" /4" /8" /2" /4" Dia. G Dia. (2 Holes) D E F 0 9 * 3/32" maximum panel thickness * V 3 Parker Hannifin orporation Division

4 atalog 0600P-5/US Flow ontrol Valves Flow ontrols & ccessories 3250 Series 1/8" to 3/4" Ports pplication The 3250 Series Flow ontrol Valves are specifically designed to accurately meter the flow of air in one direction and allow free flow in the opposite direction. The 3250 Series Flow ontrol Valves are also suitable for low pressure hydraulic service. Operation F When air is moving in the free flow direction through the valve, it forces the poppet off its seat and unrestricted air flow is permitted. D E (losed) FULL FLOW DJ FLOW When air is moving in the metered direction through the valve, air pressure and the force of the poppet spring causes the poppet to close. Flow must then be through the orifice that is controlled by the metering screw. Opening this screw allows more flow; closing it, less flow. Technical Specifications ody: rass Port Size: 1/8", 1/4", 3/8", 1/2", 3/4" Internal omponents: rass, Stainless Steel Seals: una N : Standard: 40 F to 180 F Extended Options: 20 F to 400 F Operating Pressures: ir: 250 PSIG Hydraulic: 250 PSIG Valve will operate mounted in any position. Lock nut on metering screw prevents change in setting during operation. Flow Rating (SFM) Flow Path Valve Port Size 1/8" 1/4" 3/8" 1/2" 3/4" Maximum Flow in Metered Direction Maximum Flow in Free Flow Direction Model Selection Information and Dimensions Model Number Port Size NPTF 1/8" 1/4" 3/8" 1/2" 3/4" Inches mm Inches mm Inches mm Inches mm Inches mm D E F Parker Hannifin orporation Division

5 atalog 0600P-5/US Flow ontrol Valves Flow ontrols & ccessories 3250 Series 1", 1-1/4" & 1-1/2" Ports pplication These extra large flow control valves have been developed to provide effective flow settings for large diameter cylinders and for other similar air applications. Each valve has a fine screw adjustment allowing precise settings which are secured by a sturdy lock nut. Operation F dj Flow (losed) D Full Flow G H (Hex) E Large internal port passages coupled with unique soft seal poppet and inline design provide maximum full flow capacity and minimum pressure drop in the free flow direction. Their cone shaped brass metering valve will provide consistent cylinder speed by regulating cylinder exhaust. Technical Specifications Flow apacity In Full Flow Direction ody: ast luminum Port Size: 1", 1-1/4", 1-1/2" Internal omponents: rass, luminum Seals: una N, Urethane Spring: Stainless Steel : Standard: 40 F to 180 F Extended Options: 40 F to 350 F Port Max. Flow Size (Needle Open) Model (NPTF) Number SFM** v / / ** t 100 PSIG inlet pressure with full pressure drop. Operating Pressures: Maximum ir: 250 PSIG Model Selection Information and Dimensions Model Number Port Size NPTF 1" 1-1/4" 1-1/2" Inches mm Inches mm Inches mm D E F G H V 5 Parker Hannifin orporation Division

6 atalog 0600P-5/US Miniature Right ngle Flow ontrol Flow ontrols & ccessories M5 (10-32) Port General Information 3mm Dia. Miniature right angle flow controls provide meter out control of exhaust air from an air cylinder while providing full flow in the reverse direction. The M5 (10-32) male thread can be used to mount directly to cylinder ports. The inlet ports are available in M5 (10-32) male or 5/32" instant tube fitting. The adjustment screw is captive and discourages tampering. This compact flow control saves space and reduces the number of fittings involved in making the connection. Plumbing can be oriented 360 about the cylinder port. L K H 145 PSIG (10 bar) omponent Materials ody: Polyamide Mounting thread: rass 0 to 140 F* * mbient temperatures below freezing require moisture-free air. mbient temperatures below freezing and above 180 require lubricants especially selected for suitability at these temperatures. valves should be used with filtered and lubricated air. Model Selection Ports Wrench Male Female Size Model Number M5 M5 5/16" PWRE14557 M5 5/32" Tube 5/16" PWRE14457 Note: Standard fittings will fit the M5 threads on valve body. Dimensions - Inches (mm) K H L (11) (4) (7,2) (17) (20) Flow No of Exhaust Inlet Turns (Screw Open) (Screw losed) SFM 1.8 SFM 6 Parker Hannifin orporation Division

7 atalog 0600P-5/US Right ngle Flow ontrol Valves Flow ontrols & ccessories 3251 Series Shown with Threaded Inlet Shown with Prestolok Inlet Fitting 1 Metered Flow Open Free Flow pplication The Right ngle Flow ontrol is an ideal solution to cylinder speed control where space is at a premium. ostly fittings, connections and piping expenses can be eliminated because the valve can rotate 360, the piping alignment can be in any direction. It then locks into place. The 1/8" model can be rotated after final assembly. Operation Install by threading male end directly into cylinder port. The free-flow and metered-flow direction is automatically predetermined. Free-flow direction is into cylinder and metered-flow is out of the cylinder. Flow is adjusted with an llen wrench and locked with nut. Right ngle Flow ontrol also available with Prestolok fittings on inlet port to accommodate 5/32-3/8 tube sizes. This allows for quick connection and eliminates need for separate tube fitting. ody: rass Plunger: rass and cetal Seals: una N Temperature Range: 0 F to 140 F ( 18 to 60 ) Pressure Rating: 125 PSIG (863 kpa) max. Model Selection Information and Dimensions Thread Thread Weight v Model (NPT) (NPT) djusted Free Number Inches mm Inches mm Inches mm oz. kg. Male Female Flow Flow /8 1/ /4 1/ /8 3/ /2 1/ With Prestolok Thread Tube Fittings (NPT) Size 1 Weight v /8 5/ /8 1/ /4 1/ /4 3/ /8 3/ V! UTION: If it is possible that the ambient temperature may fall below freezing, the medium must be moisture-free to prevent internal damage or unpredictable behavior. 7 Parker Hannifin orporation Division

8 atalog 0600P-5/US Miniature Right ngle Flow ontrol Flow ontrols & ccessories FM701 & FM703 Series General Information FM701 H D L M Miniature right angle flow controls provide meter out control of exhaust air from an air cylinder while providing full flow in the reverse direction. The male thread can be used to mount directly to cylinder ports. The inlet ports are available in 5-32 or 1/4" instant tube fittings. The adjustment screw is captive and discourages tampering. This compact flow control saves space and reduces the number of fittings involved in making the connection. Plumbing can be oriented 360 about the cylinder port. H 145 PSIG (10 bar, 1000 kpa) max. FM703 omponent Materials D L M Temperature Range* 0 F to 140 F (-18 to 60 ) * mbient temperatures below freezing require moisture-free air. mbient temperatures below freezing and above 180 require lubricants especially selected for suitability at these temperatures. valves should be used with filtered and lubricated air. ody: Polyamide Mounting thread: rass Dimensions Miniature Exhaust Flow ontrol FM701 omposite ody Tube Thread Hex H H Flow djusted Free Flow Part No. Size Size (mm) losed Open L M Dia. D Flow (SFM) (SFM) FM701-5/32-0 5/ FM701-5/32-2 5/32 1/ FM / FM /4 1/ FM /4 1/ Knobless Miniature Exhaust Flow ontrol FM703 omposite ody Tube Thread Hex H H Flow djusted Free Flow Part No. Size Size (mm) losed Open L M Dia. D Flow (SFM) (SFM) FM703-5/32-0 5/ FM /4 1/ FM /4 1/ Parker Hannifin orporation Division

9 atalog 0600P-5/US Right ngle Flow ontrol Valves Flow ontrols & ccessories F701, F702 & FS701 Series J L Open L losed M Hex 1 Hex 2 pplication The Right ngle Flow ontrol is an ideal solution to cylinder speed control where space is at a premium. ostly fittings, connections and piping expenses can be eliminated because the valve can rotate 360, the piping alignment can be in any direction. It then locks into place. F701 F702 J L losed L Open Hex 2 J N M Hex 1 Hex 2 N M Operation Install by threading male end directly into cylinder port. The free-flow and metered-flow direction is automatically predetermined. Free-flow direction is into cylinder and metered-flow is out of the cylinder. Flow is adjusted with an llen wrench and locked with nut. F701 Series is available with Prestolok fittings on inlet port to accommodate 1/8 1/2 tube sizes. This allows for quick connection and eliminates need for separate tube fitting. F702 Series is available with a threaded inlet connection. FS701 Series is available with a swivel outlet, for use where access is restricted. FS701 Dimensions Hex 1 L Open Hex 2 L losed N ody: rass lack Epoxy oated olt Material: rass Plunger: rass and cetal Seals: una N Temperature Range: -10 F to 200 F (-23 to 93 ) Pressure Rating: 145 PSIG (10 bar, 1000 kpa) max. Tube Thread Hex Hex L L djusted Free Flow Part No. Size Size 1 2 Open losed N M J Flow (SFM) (SFM) Flow ontrol with Push-in onnecton F701 F / /16 5/ F /8 1/8 5/16 5/ F701-5/32-0 5/ /16 5/ F701-5/32-2 5/32 1/8 5/16 5/ F701-5/32-4 5/32 1/4 5/16 5/ F /4 1/8 5/16 5/ F /4 1/4 5/16 5/ F /4 3/8 5/16 13/ F /8 1/4 5/16 5/ F /8 3/8 5/16 13/ F /8 1/2 9/ F /2 1/2 9/ Flow ontrol with Threaded onnection F702 F /8 1/8 5/16 5/ F /4 1/4 5/16 5/ F /8 3/8 5/16 13/ F /2 1/2 9/ Flow ontrol with Swivel Outlet FS701 FS /8 1/8 5/16 5/ FS701-5/32-0 5/ /16 5/ FS701-5/32-2 5/32 1/8 5/16 5/ FS701-5/32-4 5/32 1/4 5/16 5/ FS /4 1/8 5/16 5/ FS /4 1/4 5/16 5/ FS /16 1/4 5/16 5/ FS /8 1/4 5/16 5/ FS /8 3/8 5/16 13/ FS /8 1/2 9/ V 9 Parker Hannifin orporation Division

10 atalog 0600P-5/US Needle Valves Flow ontrols & ccessories SPN Series 1/8" to 1/2" Ports General Information The SPN Series needle valves provide excellent bi-directional speed control for pneumatic and hydraulic applications. D E F (Open) (oth Ends) SPN valves are manufactured with a two step needle. Fine metering is accomplished over the initial adjustment turns and nominal metering is provided over the remaining turns. Once the desired flow is selected, a set screw can be tightened to maintain the setting. These valves are available with NPTF ports in 1/8", 1/4", 3/8" and 1/2" sizes. omponent Materials ody: rass Needle: Stainless Steel Needle seals: Nitrile (Standard), Fluorocarbon (Optional) Knob: luminum 2000 PSI Non-Shock Standard: 0 to 140 F* Extended temperature: 0 to 400 F* * mbient temperatures below freezing require moisture-free air. mbient temperatures below freezing and above 180 require lubricants especially selected for suitability at these temperatures. valves should be used with filtered and lubricated air. Model Selection and Dimensions Model Number Port Size D E F SPN200 1/8-27 NPTF SPN400 1/4-18 NPTF SPN600 3/8-18 NPTF SPN800 1/2-14 NPTF For units with Fluorocarbon seals, add suffix V. Example: SPN200V Performance Data ontrolled Flow Needle Full Open Model Flow - SFM rea 100 PSI v Sq. Inches Full DP SPN SPN SPN SPN Parker Hannifin orporation Division

11 atalog 0600P-5/US Needle Valves Flow ontrols & ccessories 338 Series 1/8" to 3/4" Ports O-ring for friction 1 DI H1 - OPEN H2 - LOSED General Information 338 Series needle valves bi-directionally meter the flow of air through the valve. This series features a fine tapered needle providing precise flow of air in both directions. Numerical micrometer position markings are stamped on the perimeter of the adjustment knob which provide a visual indication of the setting. Once the desired flow is selected, a set screw can be tightened to maintain the setting. These valves are available with NPTF ports in 1/8", 1/4", 3/8" 1/2" and 3/4" sizes. This series is recommended for pneumatic service. omponent Materials ody Material: rass Internal omponents: Stainless Steel/rass Seals: Nitrile (Fluorocarbon optional consult factory) 250 PSIG (ir) Standard: 0 to 180 F* Extended Temperature: 0 F to 300 F* (onsult factory) * mbient temperatures below freezing require moisture-free air. mbient temperatures below freezing and above 180 require lubricants especially selected for suitability at these temperatures. valves should be used with filtered and lubricated air. Model Selection and Dimensions Port Dimensions Service Size Model H1 H2 Kit 1/8" /16" /4" /16" /8" /8" /2" /16" /4" /8" Performance Data Flow V Port Model Flow Size Number (SFM ) 1/8" /4" /8" /2" /4" t 100 PSIG inlet pressure with full pressure drop. 11 Parker Hannifin orporation Division

12 atalog 0600P-5/US heck Valves Flow ontrols & ccessories SP Series 1/8" to 1/2" Ports General Description heck valves provide free flow of air or oil in one direction and dependable shutoff in the opposite direction. These valves are available with NPTF ports in 1/8", 1/4", 3/8" and 1/2" sizes. D Sq. Free Flow omponent Materials ody: rass Poppet: Stainless Steel Poppet Seal: una (Nitrile) Poppet Retainer: Stainless Steel Spring: Stainless Steel Poppet Style: Soft Seal Standard 2000 PSI Non-Shock 5 PSIG racking Pressure 0 to 140 F* -40 to 140 F (Hydraulic service) * mbient temperatures below freezing require moisture-free air. mbient temperatures below freezing and above 180 require lubricants especially selected for suitability at these temperatures. valves should be used with filtered and lubricated air. Model Selection and Dimensions Model Number Port Size D SP200 1/8-27 NPTF SP400 1/4-18 NPTF SP600 3/8-18 NPTF SP800 1/2-14 NPTF Performance Data - Flow Model Port Size Free Flow Orifice v Number Inches SFM* area, in. 2 SP200 1/8-27 NPTF SP400 1/4-18 NPTF SP600 3/8-18 NPTF SP800 1/2-14 NPTF * t 100 PSI, Full P 12 Parker Hannifin orporation Division

13 atalog 0600P-5/US heck Valves 339 Series 1/8" to 3/4" Ports Flow ontrols & ccessories 339 Series & 3047 Series /4" Male Pipe 13/16 Hex 35/64 Flats.22 (6) Dia (59) General Information 339 Series check valves allow free flow in one direction and provide positive checked (zero flow) in the reverse direction. These valves are available with NPTF ports in 1/8", 1/4", 3/8", 1/2" & 3/4" sizes. This series is recommended for pneumatic service. 250 PSIG racking Pressure: 1 to 2 PSIG Standard: 0 to 180 F* Extended Temperature Option: 0 F to 300 F* omponent Materials ody Material: rass Internal omponents: rass/ Stainless Steel/ Zinc- Plated Steel Seals: Urethane (standard), Fluorocarbon (optional consult factory) Model Selection and Dimensions Port Model Flow Dimensions Service Size Number (SFM) Kit 1/8" /4" /8" /2" /4" General Information 3047 Series check valves allow free flow in one direction and provide positive checked (zero flow) in the reverse direction. This valve is available with a male 1/4" NPTF connection and is recommended for pneumatic service. 250 PSIG racking Pressure: 1 to 2 PSIG Standard: 0 to 180 F* * mbient temperatures below freezing require moisture-free air. mbient temperatures below freezing and above 180 require lubricants especially selected for suitability at these temperatures. valves should be used with filtered and lubricated air. omponent Materials ody Material: rass Internal omponents: rass/stainless Steel Seals: Nitrile Model Selection Pipe Model Flow Thread Number (SFM) 1/4" t 100 PSIG inlet pressure with full pressure drop. 13 Parker Hannifin orporation Division V

14 atalog 0600P-5/US Muffler / Filters, Muffler / Flow ontrols Flow ontrols & ccessories EM Series & Muffler / Flow ontrols EM Series Sintered ronze Muffler / Filters Muffler/filters effectively reduce air exhaust noises to an industry accepted level with minimum flow restriction. They protect valves, impact wrenches, screw drivers and other air tools by preventing dirt and other foreign matter from entering the system. Noncorrosive. an be cleaned with many common solvents. 250 PSIG (ir) 0 to 300 F* Pipe Thread Model Number Overall Length Hex Size 1/8" EM /16" 1/4" EM /16" 3/8" EM /16" 1/2" EM /8" 3/4" EM /6" 1" EM /16" 1-1/4" EM /16" 1-1/2" EM " Muffler / Flow ontrols Muffler/flow controls provide an acceptable exhaust noise level and effectively meter exhaust. Installed in valve exhaust ports, they control cylinder piston speeds throughout a wide range. The adjusting screw cannot be accidently blown out, can be locked to maintain setting. rass and bronze construction. lean with commonly used solvents. 250 PSIG (ir) 0 to 300 F* Pipe Thread Model Number Overall Length Hex Size 1/8" /16" 1/4" /2" 3/8" /16" 1/2" /8" 3/4" /16" 1" /16" 14 Parker Hannifin orporation Division

15 atalog 0600P-5/US reather Vents, Silencers Flow ontrols & ccessories reather Vents & ES Series reather Vents NOTE: reather vents should not be used as exhaust mufflers. These low silhouette versions of the muffler / filter are useful where space is a problem and/or to prevent contamination. Use for vacuum relief or pressure equalization in gear boxes, oil tanks, reservoirs, etc. Non-corrosive. 250 PSIG (ir) 0 to 300 F* * mbient temperatures below freezing require moisture-free air. mbient temperatures below freezing and above 180 require lubricants especially selected for suitability at these temperatures. valves should be used with filtered and lubricated air. Pipe Thread Model Number Overall Length Hex Size 1/8" /16" 1/4" /16" 3/8" /16" 1/2" /8" 3/4" /6" 1" /16" 1-1/4" /16" 1-1/2" " ES Series Silencer Pipe Thread E D NPT The silencer is designed to give superior performance in noise control with a minimum effect on air efficiency. Trimline design allows location in the tightest places without extra plumbing and fittings. Fits directly into the exhaust port of more than 90% of present commercial valves. Slotted body permits rapid discharge of air without undesirable back pressure. Unique nylon screen element resists dirt buildup or clogging. 250 PSIG (ir) 0 to 300 F* Model Numbers Dimensions Flow 100 PSIG Inlet NPTF SPT (R) D E 1/8" ES12M ES12M /8" 1/4" ES25M ES25M /8" 3/8" ES37M ES37M /4" 1/2" ES50M ES50M /4" 3/4" ES75M ES75M /2" 1" ES100M ES100M 1, /2" 1-1/4" ES125M ES125M 1, /2" ES150M ES150M 1, V 15 Parker Hannifin orporation Division

16 atalog 0600P-5/US ir Line Silencer Plastic Flow ontrols & ccessories SN Series M5, 1/8", 1/4", 3/8" & 1/2" Features ompact Lightweight Easy to install Excellent noise reduction Protects components from contamination NPT & SPT threads available Part Maximum Flow Sound Pressure Thread Number Level (d) (SFM) Size (mm) (mm) NPT SPT 100 PSIG Inlet 20 PSIG 100 PSIG Inlet Inlet M5 S-5 1/8" SN-6 S-6 1/4" SN-8 S-8 3/8" SN-10 S-10 1/2" SN-15 S (11) (8) (40) (16) (65) (21) (85) (25) (95) (30) pplication The plastic silencer is designed to give excellent noise reduction with a minimum effect on air efficiency. The Trimline design allows for locating the silencer in the tightest places without extra plumbing or fittings. Fits directly into the exhaust port of most commercial valves. Open surface area of element allows for rapid discharge of air without undesirable back pressure. Specifications Pressure Rating: 0 to 150 PSIG (0 to 10 bar, 0 to 1034 kpa) Temperature Rating: 14 F to 140 F (-10 to 60 ) ody: cetal (Plastic) Element: Polyethylene 16 Parker Hannifin orporation Division

17 atalog 0600P-5/US ir Line Muffler Reclassifier Flow ontrols & ccessories ES Series 1/2" & 1" Operation ompressor oils and lubricating oils are exhausted from valves, cylinders and air motors into the ES. Oil aerosols are coalesced into larger droplets and gravity pulls them into the attached drain sump. The sump can then be drained manually or by using a 1/4" ID plastic tube drain. The air flowing into the ES is also muffled or silenced as it enters the inside of the ES and passes through the filter media into the atmosphere. Performance haracteristics da Flow vs. Noise Level " Open Pipe 1/2" Open Pipe ES5 ES SFM Features dm 3 /s n bar 10 PSID Dimensions: Model ES /2" 2.57 (135 mm) NPT (65 mm) ES " 2.57 (185mm) NPT (65mm) Flow vs. ack Pressure ES3 ack Pressure ES5 ack Pressure SFM dm 3 /s n The ES (Muffler-Reclassifier) eliminates unwanted oil mist and reduces exhaust noise from pneumatic valves, cylinders and air motors % Oil removal efficiencies 25 d Noise attenuation 1/2" NPT and 1" NPT Disposable units ontinuous or plugged drain option Metal retained construction Fast exhaust time Improve Overall Plant Environment Exhaust oil mist and noise pollution have a direct impact on worker productivity. Oil aerosol mist from lubricators and compressors is pervasive and enters the industrial plant environment through the exhaust ports of valves, cylinders and air motors. This rapidly expanding exhaust also produces sudden and excessive noise. The ES (Muffler-Reclassifier) is 99.97% efficient at removing the oil aerosols. The ES also acts as a silencer to lower the d levels below O.S.H.. requirements. The result is a cleaner, quieter environment which equates to greater work productivity and safety. Proven Technology The ES units are constructed from the same materials that go into our oil removal coalescing filter elements. The seamless design insures media uniformity and strength. This proven technology provides high coalescing efficiency with low pressure drop. The filter media is supported by cylindrical perforated steel retainers both inside and out. These retainers, fully plated for excellent corrosion resistance, give the ES units high rupture strength in either flow direction. These filters can also be used as high efficiency inlet or bypass filters for vacuum pumps, or breather elements to protect the air above critical process liquids. ES3 / ES5 The ES solves two problems inherent in compressed air exhaust from valves, cylinders and air motors - oil mist removal and noise abatement. The ES will improve your industrial plant environment, thereby improving worker productivity. Specifications Maximum 125 F (52 ) Maximum Line Pressure 100 PSIG (690 kpa) Ordering Information ES 3 P Size 3. 1/2 inch 5. 1 Inch Engineering Level. urrent 17 Parker Hannifin orporation Division V

18 atalog 0600P-5/US utomatic Drip Leg Drain, Relief Valve utomatic Drip Leg Drain Flow ontrols & ccessories Features & Operation Relief Valve F Features uto drain ported 1/8" to pipe away liquid. Drain has manual override. Easily serviced without tool PSIG range. ompact size. Specifications Housing & ap: luminum Port Threads: 1/4" - 1/2" Top 1/8" Drain Pressure & Temperature Ratings: Metal owl: 0 to 250 PSIG (0 to 1725 kpa) 32 F to 175 F (0 to 80 ) Seals: una N Ordering Information onsists of Drip Leg Drain Housing WITH uto Drain. Model No. Size 06D1N 1/4" 06D3N 1/2" mm 60 mm 22 mm.75 Hex mm mm Features Large relief capacity in a compact size. Lightweight aluminum construction with resilient seat. pplication The RV011N Pop Off Relief Valve is designed to protect against excessive pressure buildup in a pneumatic circuit or system. Operation With the relief valve mounted in a reservoir or system, the force of system pressure at () is offset by the force of spring () acting on poppet seat (). t pressures lower than the setting, the poppet seat () is held against the body at () effecting a seal. When pressure rises above the set point, the force of the pressure lifts the poppet seat () off the body at () allowing the excess pressure to vent to atmosphere at (F). When the excess pressure has been vented, the spring () acts on the poppet seat () forcing it to seat on the body at (), sealing off the flow of air. Specification ody, Lock Nut & djusting Screw: luminum Seat: Nitrile Spring: Steel Poppet: Plastic : 32 F to 200 F (0 to 93 ) Port Threads: 1/4 Inch Male Relief Range: 50 to 200 PSIG (1.7 to 14 bar) with standard spring. onsult factory for pressures below 50 PSIG. Ordering Information RV011N 100 Standard Model With Specify Pressure Setting 1/4 Inch Male Thread PSIG Using Three Digits Standard Setting is 100 PSIG 18 Parker Hannifin orporation Division

19 atalog 0600P-5/US Relief Valves - Diaphragm Type Flow ontrols & ccessories P130 & P134 Series Inlet Inlet P130 Relief Valve Features ompact, sensitive diaphragm-type relief valve. Push-pull, locking knob. Knob and top work the same as a miniature regulator. P130 has lightweight aluminum construction. P134 has a brass body, captured exhaust and is an inline type with 3 inlet ports and 1 outlet port. pplications Designed to protect against excessive pressure buildup in a pneumatic circuit or system. For use where gradual proportional relief is required. Operation Turn relief valve knob clockwise for maximum pressure. Set pressure going into relief valve at desired pressure. Turn relief valve knob counter-clockwise until exhaust starts to bleed. Turn relief valve knob clockwise until exhaust stops bleeding. Push to lock knob. Ordering Information Relief Spring Range Valve 0-15 PSIG 0-25 PSIG 0-50 PSIG PSIG P130 P134 P P P P P130-02P* P130-02P* P130-02P* P130-02P* P P P P P134-02P* P134-02P* P134-02P* P134-02P* * Panel mount nut included. P134 Relief Valve Dimensions.22 Dia. 1/4" Pipe INLET mm P mm mm mm mm Relief Valve Kits onnet ssembly Kit... PKR364Y Panel Mount Nut... PR05X51 Specifications 1/4" Pipe INLET mm 1/8" Pipe INLET FRONT & K FLOW DIRETION P mm mm mm mm Relief Range... 0 to 100 PSIG (0 to 6.9 bar) Maximum Inlet Pressure PSIG (20.7 bar) F to 120 F (4 to 49 ) Port Threads P130:... 1/4" Pipe Male Only P134:... Inlet Port Two 1/8" & One 1/4" Pipe Outlet Port 1/4" Pipe Materials of onstruction djusting Knob... Polypropylene djusting Screw... Zinc-plated Steel ody... luminum (P130); rass (P134) Diaphragm / Disc... una-n Nut... hromated Steel Spring age... cetal Spring... Zinc-plated Steel 19 Parker Hannifin orporation Division 1/4" Pipe OUTLET V

20 atalog 0600P-5/US Quick Exhaust & Shuttle Valves Flow ontrols & ccessories 0R Series 1/8" thru 3/4" Ports Port 3 (Exh) General Information Quick exhaust valves provide rapid exhaust of control air when placed between control valve and actuator. They can also be used as shuttle valves. Diaphragm materials are available in urethane, Nitrile, Fluorocarbon, and PTFE to meet a wide variety of operating conditions. 1 3 Port 1 (In) 2 Port 2 (yl) Operating Pressure (ir) Maximum: 150 PSIG 200 PSIG for Model No (PTFE diaphragm) Minimum: 3 PSIG 50 PSIG for Model No (PTFE diaphragm) Urethane: 0 F to 180 F* (-18 to 80 ) Nitrile: 0 F to 180 F* (-18 to 80 ) Fluorocarbon: 0 F to 400 F* (-18 to 205 ) PTFE: 0 F to 500 F* (-18 to 260 ) * mbient temperatures below freezing require moisture-free air. mbient temperatures below freezing and above 180 require lubricants especially selected for suitability at these temperatures. valves should be used with filtered and lubricated air. omponent Materials ody Material: Die cast aluminum Static Seals: Nitrile standard with urethane (Others see below) Diaphragm: Standard Urethane Optional Fluorocarbon, PTFE, or Nitrile (Depending on size) Mounting racket Kit No (Including body screws) For 0R12 and 0R25 sizes. Model Selection, Performance Data and Dimensions Port Flow Model Number Service (SFM ) NPTF SPP G Kit No. STNDRD URETHNE DIPHRGMS (Nitrile static seals) 1/8" 1/8" 1/8" 70 0R12 0R12 7/8" Sq /8" 1/4" 70 0R12N 0R12N 7/8" Sq /4" 1/4" 90 0R25 0R25 7/8" Sq /4" 1/4" 3/8" 150 0R25N 0R25N 1" Hex /8" 3/8" 240 0R25P 0R25P 1" Hex /8" 3/8" 3/8" 240 0R37 0R37 1" Hex /2" 1/2" 1/2" 450 0R50 0R50 1-1/2" Hex /4" 3/4" 3/4" 550 0R75 0R75 1-1/2" Hex NITRILE DIPHRGMS (Nitrile static seals) 1/4" 1/4" 3/8" 90 0R25NF 0R25NF 7/8" Sq /8" 3/8" 150 0R25PF 0R25PF 1" Hex /8" 3/8" 3/8" 240 0R37F 0R37F 1" Hex /4" 3/4" 3/4" 550 0R75F 0R75F 1-1/2" Hex FLUORORON DIPHRGMS for extended temperature operation (Fluorocarbon static seals) 1/8" 1/8" 1/8" 70 0R12V 0R12V 7/8" Sq /8" 1/4" 70 0R12NV 0R12NV 7/8" Sq /4" 1/4" 1/4" 90 0R25V 0R25V 7/8" Sq /8" 3/8" 3/8" 240 0R37V 0R37V 1" Hex /2" 1/2" 1/2" 450 0R50V 0R50V 1-1/2" Hex /4" 3/4" 3/4" 550 0R75V 0R75V 1-1/2" Hex PTFE DIPHRGMS for higher pressure and temperature (Fibre static seals) 3/8" 3/8" 3/8" 240 0R37T 0R37T 1" Hex t 100 PSIG inlet pressure with full pressure drop. old Numbers are Standard. 20 Parker Hannifin orporation Division

21 atalog 0600P-5/US Quick Exhaust & Shuttle Valve Flow ontrols & ccessories Typical pplications Typical Quick Exhaust Valve pplications PRESSURE MN PRESSURE REG PRESSURE Rapid Retraction Double cting ylinder In this circuit, air is exhausted through a Quick Exhaust Valve that is close coupled to the cap end of the cylinder. ecause the Quick Exhaust Valve has a greater exhaust capacity than the four-way ontrol Valve, increased cylinder speed can be accomplished with a smaller and less expensive control valve. Dual Pressure ctuation of Double cting ylinder This circuit utilizes a Quick Exhaust Valve and a three-way ontrol Valve to permit rapid extension of the cylinder at a high pressure. Retraction can be accomplished at a lower pressure, thus saving air and increasing cylinder life. NOTE: Line pressure must be 3 or 4 times greater than rod end pressure. Effective working pressure is the differential between the cap and rod end. i-directional ontrol of Two Double cting ylinders This circuit provides maximum control with a minimum of valving. large four-way ontrol Valve is not needed to permit the rapid retraction of ylinder, as the Quick Exhaust Valve performs this function. The extension of ylinders and and retraction of ylinder are controlled by Speed ontrol Valves. Typical Shuttle Valve pplications MN M N OPERTION MN OPERTION 2 OPERTION 3 D MN PRESSURE M N PRESSURE OPERTION 1 MN PRESSURE MN OR ircuit The most common application of the Shuttle Valve is the OR ircuit. Here a cylinder or other work device can be actuated by either control valve. The valves can be manually or electrically actuated and located in any position. Memory ircuit This circuit enables continuous operation once initiated. Pressure is delivered to the circuit when Valve is actuated. This allows pressure to pass through the shuttle valve actuating Valve. Pressure then flows through Valve and also the other side of the shuttle valve which holds Valve open for continuous operation. To unlock the circuit, Valve must be opened to exhaust the circuit and allow Valve to return to its normally closed position. Interlock This circuit prevents the occurrence of a specific operation while one or another operation takes place. When either Valve or is actuated to perform operation 1 or 2, Valve D is shifted to the closed position and prevents operation 3 from occurring. V 21 Parker Hannifin orporation Division

22 atalog 0600P-5/US Shuttle Valve Flow ontrols & ccessories 1/8" to 3/8" Ports General Information Shuttle valves determine a single pneumatic output from two separate inputs. If pressure is applied to both ports simultaneously, the valve will select the port with the higher pressure. D F E INLET G 1 INLET K (3 Ports) H INLET J L Dia. (2 Holes) 200 PSIG Maximum 3 PSIG Minimum: Differential Pressure 0 to 160 F* * mbient temperatures below freezing require moisture-free air. mbient temperatures below freezing and above 180 require lubricants especially selected for suitability at these temperatures. valves should be used with filtered and lubricated air. omponent Materials ody Material: luminum Internal omponents: luminum Seals: Nitrile Model Selection and Dimensions Port Dimensions Size Model 1 D E F G H J K L 1/8" N N/ / /4" N / /8" N / Performance Data Flow Port Model Flow Size Number (v) 1/8" N /4" N /8" N Parker Hannifin orporation Division