Drilling & Completion Summary - Ascending

Transcription

1 UNIVERSITY AI/UWI ield Name SRABERRY (TREND AREA) Spud 12/12/2014 Ground Elevation (ft) 2, roperty Sub TD 1/12/2015 KB Elevation (ft) 2,98.00 Drilling & Completion Summary - Ascending BTD (All) (ftkb) - 19,40.0 Operator IOER NATURAL RESRC USA, INC State TEXAS County ANDREWS Surface Legal Location 00' SL/ 1' EL, SEC: 5, BLK:, TW:, SVY: University Lands Drilling Rig Release rac On roduction Initial otential 1/16/2015 Total Depth (All) (ftkb) Total Depth All (TVD) (ftkb) - 19, ,99. Report #: 1 Daily Operation: 12/11/2014 1:00-12/12/2014 rimary Job ORIG DRILLING ODR 0402 Days rom Spud (days) Days on Location (days) End Depth (ftkb) End Depth (TVD) (ftkb) Dens Last Mud (lb/gal) Rig Check re Skid check list; Rig down & prepare to skid; Skid f/ University to University -4 22; Rigging up & preparing to spud; Install conductor & lowline Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: hrs 12/12/2014 Spud hrs 12/12/2014 Intermediate TD Released Rig RIG NT: 0 hours for previous 24 hrs., 0 hours for the month of December 2014 Completion ercentage: 0% Surface hole drilled Completion ercentage: 0 % Intermediate drilled, Water 6,469 bbls Used 625 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 No accidents, Incidents or spills reported last 24hrs. 0.0 MD 12/11/2014 1:00 12/11/ :00 12/12/ :0 12/11/ :00 12/12/ :0 12/12/ LAN MOB MIRU JSM on re skid; Go over reskid check list; Knock std pipe loose; Clean skid rails, Knock pins out of BOE traveler, Remove low line; Begin skidding rig 22'; Rig over University :00 hrs 12/11/ LAN MOB MIRU Install Extentions to choke; add mud line extentions; Install safety cables on mud lines; Set in flow line stands, Install flow line extentions 4.5 LAN EQUI WLEAD Install Conductor; Connect flow line to conductor; Install turnbuckles age 1/92

2 Report #: 2 Daily Operation: 12/12/ /1/2014 rimary Job ORIG DRILLING ODR 0402 Days rom Spud (days) 0 Days on Location (days) 2 End Depth (ftkb) 1,600.0 End Depth (TVD) (ftkb) 1,599.8 Dens Last Mud (lb/gal) 8.0 Rig &, 6 repare to Spud; respud inspection; 18:0 hrs 12/12/2014. Drld surf 12' to 1600' 128 fph); 85% complete. RR to spud 29.5 hrs (1.2 days). Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 01:0 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Intermediate TD: Released Rig RIG NT: 0 hours for previous 24 hrs., 0 hours for the month of December 2014 Completion ercentage: 85% Surface hole drilled Completion ercentage: 0 % Intermediate drilled, Water bbls Used 626 bbls Total used: 1251 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 No accidents, Incidents or spills reported last 24hrs. 129` MD_1.08 INC_16.48 AZM_128' TVD_DLS: 0.24_' /Center_5' /21 12/12/ /12/ :00 12/12/ :0 12/12/ :00 12/12/ :0 12/1/ MOBILIZATION MIRU MIRU inish R/U flowline, center over hole & tie down conductor, R/U fill up line, put mouse hole, hook up cellar jet hoses, cellar covers around conductors. test mud lines, R/U elevators on & re Sud Inspection check list, 4.5 LAN EQUI BA JSA/ Layout direction BA & /U 1 1/2" Ulterra bit. Scrib mtr. instal MWD, Tool, M/U bit. & / U D.C. tag 120'. ; Test MWD 11.5 SUR-DRILL DRILL SURACE DRL Rotate from 120' to 1600' ( 128 fph ) WOB 20k, 0 rpm, S 2200, motor diff 588, 800 GM, torque 18 k age 2/92

3 Report #: Daily Operation: 12/1/ /14/2014 rimary Job ORIG DRILLING ODR 0402 Days rom Spud (days) 1 Days on Location (days) End Depth (ftkb) 1,859.0 End Depth (TVD) (ftkb) 1,858.5 Dens Last Mud (lb/gal) 8.60 Rig &, 6 Drld. Surface f/1600' to 1859' 09: , TOO SLM ( No Corrections) L/D Direct. BA & BIT, Clean floor, install bails ext. & C/O elevators. S/M, R/U csg running equip & Run 45 jts. of 1 /8" 54.5 J-55 Butt. csg to 1,859'; CBU; S/M, R/U Basic Cmt. Tools Surface loat 1,85.5' Surface loat 1,81.9' Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/2014 Intermediate TD: Released Rig RIG NT: 0 hours for previous 24 hrs., 0 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 0 % Intermediate drilled, Water bbls Used 615 bbls Total used: 1866 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 No accidents, Incidents or spills reported last 24hrs loat 1,85.5' loat 1,81.9' 12/1/ /1/ :00 12/1/ :00 12/1/ :00 12/1/ :00 12/1/2014 1:0 12/1/ :00 12/1/ :0 12/1/2014 2:0 12/14/ :0 12/14/2014 0:0 12/14/ :0 12/1/ :00 12/1/ :00 12/1/ :00 12/1/ :00 12/1/2014 1:0 12/1/ :00 12/1/ :0 12/1/2014 2:0 12/14/ :0 12/14/2014 0:0 12/14/ :0 12/14/2014 SUR-DRILL DRILL SURACE DRL Rotate from 1600' to 1859' 8 fph). WOB 5 k, 0 rpm, S 200, motor diff 650, 800 GM, torque 18k. (T.D. 09: ) 2 SUR-CIRC CIRCULATE CIRC ump 2-50 bbl hi vis sweep; Circulate to surface SUR-TRI TOO TRI TOO (Slick off bottom) f/1859' to 108' (SLM) No Correction / ole taking correct fill 2 LAN EQUI BA JSA - Break bit & L/D directional BA, clean floor & install bail ext. 1.5 LAN DRLG CSG TJSA / R/U ipe ros.csg. tools / TJSA on run ning 1 /8" csg. 0.5 LAN DRLG CSG Make up 1 /8 Gemco DC drillable float shoe; 1 jt 1 /8" J ppf BTC; 0.5 LAN ERS STY JSM with Morning tour crew, ipe ro casing crew & NR 5 LAN DRLG CSG Make up 1 /8" DC drillable float collar onto shoe track that day crew had made up;followed by 1 jt of 1 /8" J BTC csg; Test float equip; Continue M/U 1 /8" J BTC csg f/ 0 to1,601'; 2 SUR-CIRC CIRCULATE CIRC JSM on oisting personal; Make up Swedge in casing & begin washing csg down f/ 1,601' to 1,69' GM: LAN DRLG CSG Run 1 /8"J BTC f/ 1,69' to 1,819'; Washed f/ Tagged bttm;total of 45 jts of 1 /8" J-55 1 SUR-CIRC CIRCULATE CIRC Circulate Bttms up while Rigging down csg crew equip 1.5 SUR-CMT CEMENT SURACE CASING CMT JSM w/ Basic Cementer, & rig crew & NR; Disconnect Mud pump, Install Cementing head; Connect lines to ump truck & prepare to cement age /92

4 Report #: 4 Daily Operation: 12/14/ /15/2014 rimary Job ORIG DRILLING ODR 0402 Days rom Spud (days) 2 Days on Location (days) 4 End Depth (ftkb) 1,859.0 End Depth (TVD) (ftkb) 1,858.5 Dens Last Mud (lb/gal) 8.0 Rig &, 6 Cemented 1 /8" Surface csg; ( ull Returns & 41 bbls of Cement to Surface ) WOC; N/D conductor; Weld on wellhead; N/U BOE; Test BOE Surface Cmt.- Testl lines to 2500 psi, ump 20 bbls of fresh water spacer, Lead Cmt. 0 sx (12.80 ppg. 1.9 yield) / Tail Cmt. 50 sx.(1.60 ppg yield) / Drop plug - Displace 281bbls of fresh water, land plug, pressure up 500 psi over, hold 5 min., check float / ULL CIRC. through out job, circulated 41 bbls./119 sks to surface. Tail Cement to 150' ( 620 lift psi inal psi & 1 bbl back) loat 1,85' loat 1,818' Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/2014 Intermediate TD: Released Rig RIG NT: 0 hours for previous 24 hrs., 0 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 0 % Intermediate drilled, Water 8,19 bbls Used 609 bbls Total used: 245 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 No accidents, Incidents or spills reported last 24hrs loat 1,85' loat 1,818' ull Returns during Surface Cement job / Lead Cement to Surface 41 bbls of Cement to Surface -Tail Cement to 1,50' 12/14/ /14/ :0 12/14/ :0 12/14/ :0 12/14/ :0 12/14/ :0 12/15/2014 0:00 12/14/ :0 12/14/ :0 12/14/ :0 12/14/ :0 12/14/ :0 12/15/2014 0:00 12/15/ SUR-CMT CEMENT SURACE CASING CMT Surface Cmt.- Testl lines to 2500 psi, ump 20 bbls of fresh water spacer, Lead Cmt. 0 sx (12.80 ppg. 1.9 yield) / Tail Cmt. 50 sx.(1.60 ppg yield) / Drop plug - Displace 281bbls of fresh water, land plug, pressure up 500 psi over, hold 5 min., check float / ULL CIRC. through out job, circulated 41 bbls./119 sks to surface. Tail Cement to 150' ( 620 lift psi inal psi & 1 bbl back) 1 LAN DRLG CMTRI Safety Meeting W/ Basic Cementers, Rig down Cement ead & all Basic Cmt. Tools 2 LAN EQUI BOS JSM - N/D low line Conductor, Turn buckles on conductor 4 LAN EQUI WLEAD /U conductor, Rough cut 1 /8" Surface casing; L/D cut off 1 /8" csg & Conductor; inal cut on 1 /8" csg; Install well head; & weld same; Test well head to 500 psi 1 LAN EQUI WLEAD Remove Casing elevators, Extension bailes, & Casing bowl 10.5 LAN EQUI BOS JSM w/ & rig crew, Mid Central N/U crew & NR: Nipple up BOE, Rotaing ead, Orbit valve; All Related Equip. LAN EQUI BOS JSM; w/ & rig crew, Mid Central Testing & NR; Test BOE 250 psi Low on all test; 1500 psi igh on Annular, 2500 psi igh on all other Test ; Test Casing 500 psi igh on casing for 0 min, 250 psi low for 5 mins/ rep- to test Rams age 4/92

5 Report #: 5 Daily Operation: 12/15/ /16/2014 rimary Job ORIG DRILLING ODR 0402 Days rom Spud (days) Days on Location (days) 5 End Depth (ftkb) 2,520.0 End Depth (TVD) (ftkb) 2,519.2 Dens Last Mud (lb/gal) 9.0 Rig &, 6 Testing BOE; icking up BA # 2; TI; Slip & Cut Drill Line; Drill loat Equip; Start 22:0 hrs 12/15/2014. Drld int 1859' to 2520' 88 fph ); 10% complete 84% Rot, 1% sldg JSM; w/ & rig crew, Mid Central Testing & NR; Test BO Rams, CR, Manifold, Upper/Lower Kelly Valves, & TIW Safety/Dart 250 psi Low/ 2500 psi igh Annular test 1500 psi igh /250 low;( GoodTest) Test Csg.@ 250 low f/ 5 Mins. & 500 psi f/ 0 Mins. w/ Mid-Central Tester. (No Leak) Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: TD: Released Rig RIG NT: 0 hours for previous 24 hrs., 0 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 10 % Intermediate drilled, Water 8,92 bbls Used 608 bbls Total used: 08 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 No accidents, Incidents or spills reported last 24hrs loat 1,85' loat 1,818' ull Returns during Surface Cement job / Lead Cement to Surface 41 bbls of Cement to Surface -Tail Cement to 1,50' Survey: MD: Inc: 1.5 Azm: /15/ /15/ :00 12/15/ :0 12/15/ :0 12/15/2014 1:00 12/15/ :00 12/15/ :0 12/15/ :0 12/16/ :00 12/16/ :00 12/15/ :00 12/15/ :0 12/15/ :0 12/15/2014 1:00 12/15/ :00 12/15/ :0 12/15/ :0 12/16/ :00 12/16/ :00 12/16/2014 LAN EQUI BOS JSM; w/ & rig crew, Mid Central Testing & NR; Test BO Rams, CR, Manifold, Upper/Lower Kelly Valves, & TIW Safety/Dart 250 psi Low/ 2500 psi igh Annular test 1500 psi igh /250 low; GoodTest 0.5 SUR-TST CSG/DO/IT TEST CSG/DRILL OUT/IT TEST CSG/DRI LL OUT/IT Test Csg.@ 250 low f/ 5 Mins. & 500 psi f/ 0 Mins. w/ Mid- Central Tester. (No Leak) 1 LAN EQUI BOS Rig Down BO Testing Equip; Install Wear Bushing: repare floor for icking up BA # LAN EQUI BA ick up Mud motor IBS, NMDC, Scribe Mud motor, Install MWD, M/U 12 1/4" bit INT-TRI IN OLE TRI IN OLE TI Trip in hole to 1,588' 4.5 LAN DRLG CUTDL Install Rotaing head; JSM with & rig crew SLip & Cut drill Line; Check Crown saver, Calibrate Drawworks, ( Took longer to slip & cut drill line due to inexperence personel ) 2 LAN DRLG DRLCMT Drill f/ 1,588' to1,818'; Drill float 1,81, loat 1,85-1,859' 1.5 INT-DRILL-VERT DRILL INT VERT- 1 INT-DRILL-VERT DRILL INT VERT- 5 INT-DRILL-VERT DRILL INT VERT- DRL- DRL- DRL- Rotate from 1859' to 1961' 108 fph). WOB 10k50 rpm, motor diff 5, 655 GM, torque 8.5k. Slide from 1961' to 1991' 0 fph). 180 GT, WOB 18k, motor diff 15, 0 GM. Rotate from 1991' to 2520' 106 fph). WOB 28k, 60 rpm, motor diff 400, 800 GM, torque 9.5.k. age 5/92

6 Report #: 6 Daily Operation: 12/16/ /1/2014 rimary Job ORIG DRILLING ODR 0402 Days rom Spud (days) 4 Days on Location (days) 6 End Depth (ftkb) 4,611.0 End Depth (TVD) (ftkb) 4,609. Dens Last Mud (lb/gal) 9.40 Rig &, 6 Drld int 2520' to 4611' 89 fph); 4% complete; 94% rot, 6% sldg.; Ser Rig; (StartDisplace hole to 9.6 to 40 vis w/prehydrated gel@ 4450') Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: TD: Released Rig RIG NT: 0 hours for previous 24 hrs., 0 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 4% Intermediate drilled, Water 9,99 bbls Used 42 bbls Total used: 555 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 No accidents, Incidents or spills reported last 24hrs loat 1,85' loat 1,818' 461` MD_1.29 INC_ AZM_459' TVD_DLS: 0.09_5' /Center 12/16/ /16/ :0 12/16/ :00 12/16/ :0 12/16/2014 1:00 12/16/ :0 12/16/ :00 12/16/ :0 12/16/2014 1:00 12/1/ INT-DRILL-VERT DRILL INT VERT- 1.5 INT-DRILL-VERT DRILL INT VERT- 0.5 INT-DRILL-VERT DRILL INT VERT- DRL- Rotate from 2520' to 45' 111 fph). WOB 0 k, 0 rpm, motor diff 480, 801 GM, torque 10. k. DRL- DRL- 0.5 LAN EQUI RIGSER Lubricate Rig 1 INT-DRILL-VERT DRILL INT VERT- DRL- Slide from 45' to 510' 2. fph). WOB 18k, motor diff 290, 800 GM. Rotate from 510' to 562' 104 fph). WOB 18k, 0 rpm, motor diff 500, 801 GM, torque 12k. Rotate from 562' to 4611' 81 fph). WOB 0k, 60 rpm, motor diff 400, 800 GM, torque 10k. age 6/92

7 Report #: Daily Operation: 12/1/ /18/2014 rimary Job ORIG DRILLING ODR 0402 Days rom Spud (days) 5 Days on Location (days) End Depth (ftkb) 5,616.0 End Depth (TVD) (ftkb) 5,614.4 Dens Last Mud (lb/gal) 9.60 Rig &, 6 Drld int 4611' to 5616' 4. fph); 59% complete; 89% rot, 11% sldg.; Ser Rig; ( Displaced hole with 9.6 ppg 40 vis w/ pre hydrated 4450') Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: TD: Released Rig RIG NT: 0 hours for previous 24 hrs., 0 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 59% Intermediate drilled, Water 9,58 bbls Used 188 bbls Total used: 4 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 No accidents, Incidents or spills reported last 24hrs loat 1,85' loat 1,818' 549` MD_0.4 INC_24.02 AZM_5495' TVD_DLS:.5_100' /Center 12/1/ /1/ :00 12/1/ :00 12/1/2014 1:0 12/1/ :00 12/1/ :0 12/1/2014 2:00 12/18/ :0 12/18/ :00 12/18/ :00 12/1/ :00 12/1/ :00 12/1/2014 1:0 12/1/ :00 12/1/ :0 12/1/2014 2:00 12/18/ :0 12/18/ :00 12/18/ :00 12/18/ INT-DRILL-VERT DRILL INT VERT- 4 INT-DRILL-VERT DRILL INT VERT-.5 INT-DRILL-VERT DRILL INT VERT- DRL- Rotate from 4611' to 469' 9.5 fph). WOB 28k, 55 rpm, motor diff 400, 844 GM, torque 11k. DRL- Rotate from 469' to 4960' 4.8 fph). WOB 28k, 50 rpm, motor diff 450, 614 GM, torque 11k. DRL- 0.5 LAN EQUI RIGSER Lubricate Rig.5 INT-DRILL-VERT DRILL INT VERT- 1.5 INT-DRILL-VERT DRILL INT VERT- 1.5 INT-DRILL-VERT DRILL INT VERT- DRL- DRL- DRL- Rotate from 4960' to 5148' 54 fph). WOB 0k, 50 rpm, motor diff 400, 614 GM, torque 11k. Rotate from 5148' to 568' 55 fph). WOB 0k, 50 rpm, motor diff 40, 614 GM, torque 1k. Slide from 568' to 540' 2. fph). 20 GT, WOB 0k, motor diff 0, 614 GM. Rotate from 540' to 546' 60 fph). WOB 5k, 50 rpm, motor diff 460, 614 GM, torque 12k. 0.5 INT-CIRC CIRCULATE CIRC Wash out mouse hole : Get Slow pump rates 1 INT-DRILL-VERT DRILL INT VERT- 4 INT-DRILL-VERT DRILL INT VERT- DRL- Slide from 546' to 549' 0 fph). WOB 5k, motor diff 460, 614 GM. DRL- Rotate from 549' to 5616' 0.8 fph). WOB 5k, 40 rpm, motor diff 50, 614 GM, torque 10.5k. age /92

8 Report #: 8 Daily Operation: 12/18/ /19/2014 rimary Job ORIG DRILLING ODR Days rom Spud (days) Days on Location (days) End Depth (ftkb) End Depth (TVD) (ftkb) 6 8 6, ,40.2 Drld int 5616' to 6409' fph); 2% complete; 89% rot, 11% sldg. Dens Last Mud (lb/gal) 9.60 Rig &, Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: TD: Released Rig RIG NT: 0 hours for previous 24 hrs., 0 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 2% Intermediate drilled, Water 9,6 bbls Used 90 bbls Total used: 8 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 No accidents, Incidents or spills reported last 24hrs loat 1,85' loat 1,818' 6254` MD_1.49 INC_41.6 AZM_6252' TVD_DLS: 0.0_100' /Center 12/18/ /18/ :00 12/18/2014 1:0 12/18/ :00 12/18/ :0 12/18/ :00 12/18/2014 1:0 12/18/ :00 12/18/ :0 12/19/ INT-DRILL-VERT DRILL INT VERT- 2.5 INT-DRILL-VERT DRILL INT VERT- 4.5 INT-DRILL-VERT DRILL INT VERT- DRL- Rotate from 5616' to 596' 5.6 fph). WOB 40k, 50 rpm, motor diff 00, 652 GM, torque 10k. DRL- 0.5 LAN EQUI RIGSER Lubricate Rig.5 INT-DRILL-VERT DRILL INT VERT- Slide from 596' to 596' 10.8 fph). WOB 0k, motor diff 15, 800 GM, torque 2k. DRL- Rotate from 596' to 6126' 6.2 fph). WOB 40k, 55 rpm, motor diff 00, 652 GM, torque 12k. DRL- Rotate from 6126' to 6409' fph). WOB 40k, 55 rpm, motor diff 00, 652 GM, torque 12k. age 8/92

9 Report #: 9 Daily Operation: 12/19/ /20/2014 rimary Job ORIG DRILLING ODR 0402 Days rom Spud (days) Days on Location (days) 9 End Depth (ftkb) 6,841.0 End Depth (TVD) (ftkb) 6,89.0 Dens Last Mud (lb/gal) 9.60 Rig &, 6 Drld int 6409' to 6841' 26.2 fph); 9% complete; 91% rot, 9% sldg. Circulate and condition mud. ump slug. Trip out of hole for slow penetration rate. Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: TD: Released Rig RIG NT: 0 hours for previous 24 hrs., 0 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 9% Intermediate drilled, Water 9,6 bbls Used 0 bbls Total used: 8 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 No accidents, Incidents or spills reported last 24hrs loat 1,85' loat 1,818' 66` MD_1.1 INC_0.10 AZM_661' TVD_DLS: 0.0_100' /Center 12/19/ /19/ :0 12/19/ :00 12/19/2014 1:0 12/19/ :00 12/19/2014 2:00 12/20/ :0 12/20/ :00 12/19/ :0 12/19/ :00 12/19/2014 1:0 12/19/ :00 12/19/2014 2:00 12/20/ :0 12/20/ :00 12/20/2014 DRL-.5 INT-DRILL-VERT DRILL INT VERT- 1.5 INT-DRILL-VERT DRILL INT VERT- 6.5 INT-DRILL-VERT DRILL INT VERT- DRL- 0.5 LAN EQUI RIGSER Lubricate Rig 5 INT-DRILL-VERT DRILL INT VERT- Rotate from 6409' to 6504' 2.1 fph). WOB 40k, 50 rpm, S 1900, motor diff 500, 58 GM, torque 12k. Slide from 6504' to 654' 20 fph). WOB 40k, 0 rpm, S 2200, motor diff 600, 840 GM, torque 0k. DRL- Rotate from 654' to 615' 2.8 fph). WOB 40k, 55 rpm, S 1900, motor diff 500, 58 GM, torque 14k. DRL- Rotate from 615' to 6841' 25.2 fph). WOB 40k, 50 rpm, S 2100, motor diff 85, 615 GM, torque 1k. 1.5 LAN WLCOND CIRC Circulate and condition mud. ump 11.0ppg slug..5 INT-TRI TOO TRI OO from 6,841' to 200' hole slick and taking proper fill. 2 LAN EQUI BA old psjm and OO racking back drill 200' age 9/92

10 Report #: 10 Daily Operation: 12/20/ /21/2014 ORIG DRILLING rimary Job ODR 0402 Days rom Spud (days) 8 Days on Location (days) 10 End Depth (ftkb),511.0 End Depth (TVD) (ftkb),508.8 Dens Last Mud (lb/gal) 9.60 Rig &, 6 Lay out motor and bit, clean floor, ick up new motor and bit #, Scribe motor and install survey tool, Trip in hole to 1860, install rotating head, test MWD tool, TI to 6841', Drld int. 6841' to 511' 52 fph); 89% complete, % rot, 2% sldg. Water meter was run over by construction crew, Butches replaced meter. Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: TD: Released Rig RIG NT: 0 hours for previous 24 hrs., 0 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 89% Intermediate drilled, Water 5 bbls Used 14 bbls Total used: 482 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 No accidents, Incidents or spills reported last 24hrs loat 1,85' loat 1,818' 200` MD_0.1 INC_22.96 AZM_19' TVD_DLS: 0.95_100' /Center 12/20/ /20/ :0 12/20/2014 0:0 12/20/ :00 12/20/2014 1:00 12/20/ :0 12/20/ :00 12/20/ :0 12/21/ :00 12/20/ :0 12/20/2014 0:0 12/20/ :00 12/20/2014 1:00 12/20/ :0 12/20/ :00 12/20/ :0 12/21/ :00 12/21/ LAN EQUI RIGSER Rig service. 1 INT-TRI TOO TRI OO from 200' to bit. Drain mud motor, break off bit. Retrive MWD. Lay down mud motor..5 LAN EQUI BA old pjsm with directional, & and ioneer rep. Clean and organize rig floor for safety. ick up Scientific 8'' 1.5 fixed /8lobe 4.0stage 0.16rpg mud motor, install MWD, scribe & test. Make up 12 1/4'' Ulterra U16M DC bit ( 4x18's, X1's) 6 INT-TRI IN OLE 1.5 INT-DRILL-VERT DRILL INT VERT- 1.5 INT-DRILL-VERT DRILL INT VERT- 2.5 INT-DRILL-VERT DRILL INT VERT- 1.5 INT-DRILL-VERT DRILL INT VERT- 6 INT-DRILL-VERT DRILL INT VERT- TRI IN OLE TI TI from 0' to 6,840' hole is slick and getting proper displacement. ( Install rotating 1800') Test MWD 1,800'. DRL- DRL- DRL- DRL- DRL- Rotate from 6841' to 6886' 0 fph). WOB 25k, 0 rpm, S 00, motor diff 165, 95 GM, torque 11k. Slide from 6886' to 6921' 2. fph). WOB k, S 00, motor diff 10, 844 GM. Rotate from 6921' to 05' 62 fph). WOB 5k, 60 rpm, S 400, motor diff 15, 844 GM, torque 11k. Slide from 05' to 105' 20 fph). WOB k, S 00, motor diff 10, 844 GM. Rotate from 105' to 511' 68 fph). WOB 5k, 60 rpm, S 500, motor diff 00, 844 GM, torque 1k. age 10/92

11 Report #: 11 Daily Operation: 12/21/ /22/2014 ORIG DRILLING rimary Job ODR 0402 Days rom Spud (days) 9 Days on Location (days) 11 End Depth (ftkb) 8,140.0 End Depth (TVD) (ftkb) 8,1.8 Dens Last Mud (lb/gal) 9.60 Rig &, 6 Drld int 511' to 548' 4'fph); Replace Standpipe O-ring on ammer Union: Drld int 548' to 82' 5 fph): Rig Service: Drld int 82' to 8140' 51 fph): 100% 180 hrs 12/21/2014. Circulate, pump sweeps to clean hole. ump slug, Trip out of hole, Laydown BA. Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: 18:0 12/21/2014 Released Rig RIG NT:.5 hours for previous 24 hrs.,.5 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 100% Intermediate drilled, Water 5 bbls Used 0 bbls Total used: 482 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 Notified Texas RRC 19:08hrs to Run 9 5/8 csg to 8140' & cement Spoke to Cindy, Operator #4 No accidents, Incidents or spills reported last 24hrs loat 1,85' loat 1,818' 806` MD_0..66 INC_18.40 AZM_80' TVD_DLS: 0._100' /Center 12/21/ /21/ :0 12/21/2014 0:00 12/21/ :00 12/21/ :0 12/21/ :0 12/21/ :00 12/22/ :0 12/21/ :0 12/21/2014 0:00 12/21/ :00 12/21/ :0 12/21/ :0 12/21/ :00 12/22/ :0 12/22/2014 DRL- 0.5 INT-DRILL-VERT DRILL INT VERT- Rotate from 511' to 548' 4 fph). WOB 5k, 60 rpm, S 000, motor diff 400, 844 GM, torque 1k. 0.5 UNLAN EQUI U_RIG Replace Stand pipe O-ring on ammer Union 5 INT-DRILL-VERT DRILL INT VERT- DRL- 0.5 LAN EQUI RIGSER Lubricate Rig 6 INT-DRILL-VERT DRILL INT VERT- DRL- Rotate from 548' to 82' 5 fph). WOB 5k, 60 rpm, S 000, motor diff 400, 844 GM, torque 1k. Rotate from 82' to 8140' 51 fph). WOB 5k, 60 rpm, S 000, motor diff 400, 844 GM, torque 1k. TD intermediate 18:0.5 INT-CIRC CIRCULATE CIRC Circulate, pumped sweeps to clean hole for intermediate casing run. 4.5 INT-TRI TOO TRI Trip out of hole, remove rotating head..5 LAN EQUI BA Laydown jars, - 6.5" drill collars, 2-8" drill collars, NM drill collars, IBS, float sub, downhole motor and bit. age 11/92

12 Report #: 12 Daily Operation: 12/22/ /2/2014 ORIG DRILLING rimary Job ODR 0402 Days rom Spud (days) 10 Days on Location (days) 12 End Depth (ftkb) 8,140.0 End Depth (TVD) (ftkb) 8,1.8 Dens Last Mud (lb/gal) 9.60 Rig &, 6 Remove wear bushing, prep floor to run casing and have safety meeting to rig up casing crew, Rig up casing crew, safety meeting on running casing, run casing, Install CRT tool, run casing, Safety Stand down, run casing to TD 8140, Circulate bottoms up waiting on Schlumberger orders on lead cement. Received orders, CRT tool would not dis-engage, waiting on ipe ros. Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: 18:0 12/21/2014 Released Rig RIG NT: 6 hours for previous 24 hrs., 6.5 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 100% Intermediate drilled, Water 5 bbls Used 0 bbls Total used: 482 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 Notified Texas RRC 19:08hrs to Run 9 5/8 csg to 8140' & cement Spoke to Cindy, Operator #4 No accidents, Incidents or spills reported last 24hrs loat 1,85' loat 1,818' 806` MD_0..66 INC_18.40 AZM_80' TVD_DLS: 0._100' /Center 12/22/ /22/2014 0:0 12/22/ :00 12/22/ :0 12/22/ :00 12/22/ :0 12/22/ :00 12/2/2014 0:00 12/2/ :00 12/22/2014 0:0 12/22/ :00 12/22/ :0 12/22/ :00 12/22/ :0 12/22/ :00 12/2/2014 0:00 12/2/ :00 12/2/ INT-TRI TOO TRI ull wear bushing and lay down same. Remove elevators, install bales extensions. Clean and organize rig floor for safety. 1.5 LAN DRLG CSG old pjsm with ipe ro, & and ioneer rep. Rig up casing related equipment. 1.5 LAN DRLG CSG Make up loat Shoe, 2 jt 9 5/8'' 4.5ppf L80IC BTC csg. shoe track, loat Collar, 1 jt. of casing. Rig up Valant CRT. ump through float equipment. All good..5 LAN DRLG CSG Run 10 jts. 9 5/8'', 4.5ppf, L80IC, BTC intermediate casing to 4' hole slick no problems. 0.5 LAN ERS STY Safety meeting with all personel on location on resposibilities on and off location..5 LAN DRLG CSG Run 1 jts. 9 5/8'', 4.5ppf, L80IC, BTC intermediate casing to 4' hole slick no problems. 5 UNLAN ERS U_CMTR S Circulate with CRT while Waiting on cement lab reports results on Lead cement from Schlumberger. 1 LAN ERS STY Safety meeting with third party on cementing with high pressure lines. Schlumberger 2 UNLAN OTR U_OTR Unable to release CRT tool, troubleshoot CRT with ipe ro tech. age 12/92

13 Report #: 1 Daily Operation: 12/2/ /24/2014 ORIG DRILLING rimary Job ODR 0402 Days rom Spud (days) 11 Days on Location (days) 1 End Depth (ftkb) 8,140.0 End Depth (TVD) (ftkb) 8,1.8 Dens Last Mud (lb/gal) 9.0 Rig &, 6 Rig up cementers, set cement head on casing, land casing, hold safety meeting on cementing with DV tool, test lines, shut down, Schlumbergers pump truck stopped working, waiting on pump truck, rig connected to cement head and pumped with rig pumps while waiting for cement pump truck. Third party truck arrived, connected lines, test lines, Bumped 1:0. Dropped DV tool bomb, Safety meeting with all personnel on location on pressuring up lines and circulating with rig pumps. ressure up and open DV tool, circulate with rig pumps, hold safety meeting with all personnel on cementing 2nd stage. Cement 2nd stage, drop plug, dispalce with 524.8bbls. lug Safety meeting with all personnel on rigging down cementers, rig down cementers. Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: 18:0 12/21/2014 Released Rig RIG NT: 4.5 hours for previous 24 hrs., 11 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 100% Intermediate drilled, Water 5 bbls Used 44 bbls Total used: 556 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 Notified Texas RRC 19:08hrs to Run 9 5/8 csg to 8140' & cement Spoke to Cindy, Operator #4 No accidents, Incidents or spills reported last 24hrs loat 1,85' loat 1,818' 806` MD_0..66 INC_18.40 AZM_80' TVD_DLS: 0._100' /Center 12/2/ /2/ :00 12/2/ :00 12/2/ :00 12/2/ :00 12/2/ :00 12/2/ :00 12/2/ :00 2 LAN DRLG CSG Unsting CRT tool & release. Set down hanger in wellhead and verify with Seaboard rep. old pjsm with cementers and finish rigging up Schlumberger cement crew. 6 UNLAN EQUI U_CMT Circulate with waiting on back up ump truck. pump truck down due to Deck Engine antifreeze leak. Replacement ump Truck on location & 100% rigged 14:00pm 4 INT-CMT CEMENT INTERMEDIATE CSG CMT old pjsm with Schlumberger, Weatherford, & & ioneer rep. Test cement lines to 1000psi low/5000psi high. Start Stage #1. ump 50bbls vis water 10lb/10bbl D208, pump 0bbls 9.5ppg Mudpush. ump Lead: 12bbls/220 11ppg, 2.95cu.ft/sack, 1. gal/sk water with 5.01 lb/sk D049, 5 lb/sk B056 ressure Seal LCMB56, 6.0 lb/sk B288/B289 Mica, 0.1% D208 Viscosifier, 10% D020 Extender, 6% D18 Silica, 0.2% D046 Anti oam, 0.% D01 Retarder, 0.5% D16 luid Loss, D % Dispersant. ump Tail: 41bbls/ ppg, 1.6 cu.ft/sk, 8.8gal/sk water with 5 lb/sk D049, 0.1% D065 Dispersant, 0.2% D046 Antioam, 5% D020 Extender. 0.5% D20 luid Loss, 0.2% D01 Retarder. Displacement 601bbls. ull returns throughout the whole job. Bump plug 500psi over psi. Test float float held, 4bbls back after bleed off. Top Of Lead: 6,864', Top Of Tail:,900' 4 LAN ERS STY Safety meeting with all personnel and drop DV tool opening cone for 45 min, pressure up to 50psi & open DV Tool. Switch to rig pump & circulate 25gpm. age 1/92

14 12/2/ :00 12/24/2014 0:00 12/24/2014 0:0 12/24/2014 0:00 12/24/2014 0:0 12/24/ :00 Drilling & Completion Summary - Ascending 5 LAN DRLG CMTRI old pjsm with Schlumberger cement crew, Weatherford DV tool hand, & rig crew & ioneer reps on 2nd Stage cement. Switch lines to Schlumberger cement truck, 50bbls Visc water/10bbl D208, 0bbls Mudpush 9.5ppg. ump Lead: 544bbls/1040sacks 11ppg, 2.95cu.ft/sk, 1. gal/sk water with5lb/sk D049, 5lb/sk B056 ressure Seal LCM B56, 6lb/sk B288/B289 Mica, 0.1% D208 Viscosifier, 10% D020 Extender, 6% D18 Silica, 0.2% D046 Antifoam, 0.% D01 Retarder, 0.5% D16 luid Loss, 0.1% D065 Dispersant. ump Tail: 61bbls/ ppg 1.6 cu.ft/sk. 8.8 gal/sk water with 5 lb/sk D049, 0.1% D065 Dispersant, 0.2% D046 Anti foam, 5% D020 Extender, 0.5% D20 luid Loss, 0.2% D01 Retarder. ull returns while cementing during 2nd stage. Displacement 512bbls, bump plug 1500psi over psi. Test floats, float held. 5bbls back after bleed off. Top Of Lead:,1', Top Of Tail: 6,564' 0.5 LAN ERS STY Safety meeting with all personnel on rigging down cementers. 0.5 LAN DRLG CMTRI Rig down Schlumberger. Report #: 14 Daily Operation: 12/24/ /25/2014 ORIG DRILLING rimary Job ODR 0402 Days rom Spud (days) 12 Days on Location (days) 14 End Depth (ftkb) 8,140.0 End Depth (TVD) (ftkb) 8,1.8 Dens Last Mud (lb/gal) 9.0 Rig &, 6 lush out flow line, choke lines and BO valves with sugar water to remove cement, Safety meeting on landing pack off tool, Landed pack off tool, verified proper landing, tightened bolts, tested to 5000psi, good test, owered down rig to troubleshoot electrical problem with generators. Main breaker for #1 generator is faulty, waiting for a new breaker. Install wear bushing, cut drilling line, Change out breaker on generator. Generator not working properly after breaker changed out, Wait on mechanic for further trouble shooting. ick up BA, trip in hole to 100'. Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: 18:0 12/21/2014 Released Rig RIG NT: 1 hours for previous 24 hrs., 24 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 100% Intermediate drilled, Completion ercentage: 0% roduction drilled. Water 5 bbls Used 44 bbls Total used: 556 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 Notified Texas RRC 19:08hrs to Run 9 5/8 csg to 8140' & cement Spoke to Cindy, Operator #4 No accidents, Incidents or spills reported last 24hrs loat 8,18' loat 8,045' 806` MD_0..66 INC_18.40 AZM_80' TVD_DLS: 0._100' /Center 12/24/ /24/2014 0:0 12/24/ :00 12/24/2014 0:0 12/24/ :00 12/24/ : LAN DRLG CMT Clean out all cement from flow line, choke manifold and BO valves. 0.5 LAN ERS STY Safety meeting with all personel on location on setting pack off tool and testing same. 4 LAN EQUI WLEAD Set pack off tool, rd party verified propper setting of tool, bolted down. Tested to 5000psi, good test, spun out landing joint and laid out. age 14/92

15 12/24/ :00 12/24/ :0 12/24/ :00 12/24/ :00 12/25/ :0 12/25/ :00 12/24/ :0 12/24/ :00 12/24/ :00 12/25/ :0 12/25/ :00 12/25/2014 Drilling & Completion Summary - Ascending 2.5 UNLAN OTR U_OTR Rigs generator and electrical components not working properly, trouble shoot problems with light plant and generators. 0.5 LAN EQUI WLEAD Install wear bushing and tighten lock down screws on well head. LAN DRLG CUTDL Cut drilling line, 6 wraps 10.5 UNLAN OTR U_OTR Wait on Breaker for generator house, Replaced breaker, generator did not work properly, called for mechanic to assist in trouble shooting generator/breaker issues. 0.5 ROD-TRI BA TRI OR BA TRI ickup BA BA 1 ROD-TRI TRI TRI Strap in hole to 100' Report #: 15 Daily Operation: 12/25/ /26/2014 ORIG DRILLING rimary Job ODR 0402 Days rom Spud (days) 1 Days on Location (days) 15 End Depth (ftkb) 8,150.0 End Depth (TVD) (ftkb) 8,14.8 Dens Last Mud (lb/gal) 9.0 Rig &, ', Test DV tool to 2000psi, test good, drill out DV tool, Trip in hole to 8045', Tagged float collar, Test casing to 2000psi, test good, Drill out float collar, drill out cement and float shoe, drill 10' formation, erform 8150', Test 9.4ppg EMW 8150' = 12psi, test good, CBU. Trip out of hole rom 8150' to 90', lay down BA and Mill tooth bit. ick up Curve BA, 200' ART Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: 18:0 12/21/2014 Released Rig RIG NT: 0 hours for previous 24 hrs., 24 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 100% Intermediate drilled, Completion ercentage: 0% roduction drilled. Water 5 bbls Used 44 bbls Total used: 556 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 Notified Texas RRC 19:08hrs to Run 9 5/8 csg to 8140' & cement Spoke to Cindy, Operator #4 No accidents, Incidents or spills reported last 24hrs loat 8,18' loat 8,045' 806` MD_0..66 INC_18.40 AZM_80' TVD_DLS: 0._100' /Center 12/25/ /25/ :0 12/25/ :00 12/25/ :00 12/25/2014 1:00 12/25/ :00 12/25/ :0 12/25/ :00 12/25/ :00 12/25/2014 1:00 12/25/ :00 12/25/ :0 4.5 ROD-TRI TRI TRI TI 1,00' to 5,950' fill up pipe every 0 stands. 0.5 ROD-TRI TRI TRI Install rotating head 1 ROD-TRI TRI TRI TI from 5,950' to 6,850'. Tag Stage 6,850'. Set 50K twice without pumps and verfiy tool is closed. All good. 1 LAN DRLG CSG Test casing above Stage tool 2000psi for 10 min. Test good. 4bbls in & out. 1 LAN DRLG DRLCMT Drill out Stage tool /6850 to 685, wipe DV tool clean. 1.5 ROD-TRI TRI TRI TI from 6,850' to 8,045' fill up pipe every 0 stands. Tag loat 8,045' age 15/92

16 12/25/ :0 12/25/ :00 12/25/ :00 12/25/ :0 12/25/ :00 12/25/2014 2:00 12/26/ :00 12/26/ :00 12/26/ :0 12/26/ :00 12/25/ :00 12/25/ :00 12/25/ :0 12/25/ :00 12/25/2014 2:00 12/26/ :00 12/26/ :00 12/26/ :0 12/26/ :00 12/26/2014 Drilling & Completion Summary - Ascending 0.5 LAN DRLG CSG Test casing above loat Collar 2000psi for 0 min, test good. 4bbls in & out. LAN DRLG DRLCMT Drill loat Collar, shoe track, loat Shoe and 10' new formation from 8,045' to 8,150'. loat 8, 045', loat 8,140' 0.5 LAN GEO LKO erform IT test with 9.4 ppg EMW with ' = 12psi, Test Good. 0.5 ROD-CIRC CIRCULATE CIRC CBU, get trip tanks full & mix slug. Check flow, well static. ROD-TRI TRI TRI OO from 8150' to 90' hole taking proper fill. Start cleaning mud pits for OBM prep. 1 LAN EQUI BA Lay down -6.5'' Drill Collars, bit sub, 8.5'' Mill Tooth Bit. Continue celaning mud pits for OBM. 1 LAN EQUI BA Safety mtg on picking up BA, clean floor, continue clean pits for OBM..5 LAN EQUI BA ick Scientific 2.12 deg. fixed /8 lobe 5.0stage 0.28rpg mud motor, NMDC, pulser sub, NM flex, X-over. Install MWD, scrobe & test surface tools. All good. Make Up 8.5'' MM64D DC bit. Continue cleaning pits for OBM. 0.5 LAN EQUI BOS Install Rotaing head. Continue cleaning pits for OBM. 1 ROD-TRI TRI TRI Trip in hole to 200' Report #: 16 Daily Operation: 12/26/ /2/2014 ORIG DRILLING rimary Job ODR 0402 Days rom Spud (days) 14 Days on Location (days) 16 End Depth (ftkb) 8,49.0 End Depth (TVD) (ftkb) 8,48.6 Dens Last Mud (lb/gal) 8.60 Rig &, 6 Trip in hole to 485', Service Rig, Trip in hole to 956', Change out rotating head rubber for OBM, Trip in hole to 8150', Displace hole with Oil Base Mud, Started 1500hrs 12/26/14. Drld vert 8150' to 8209' 118 fph); 100% 150 hrs 12/26/14. Built curve 8209' to 849' 19.6 fph); 8% complete; % rot, 9% sldg. Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: 18:0 12/21/2014 Released Rig RIG NT: 0 hours for previous 24 hrs., 24 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 100% Intermediate drilled, Completion ercentage: 15% roduction drilled. Water 5 bbls Used 44 bbls Total used: 556 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 Notified Texas RRC 19:08hrs to Run 9 5/8 csg to 8140' & cement Spoke to Cindy, Operator #4 No accidents, Incidents or spills reported last 24hrs loat 8,18' loat 8,045' 8409` MD_15.12 INC_1.4 AZM_8404' TVD_DLS:.00_100' /Center 12/26/ /26/ :0.5 ROD-TRI TRI TRI TI from 200' to 4,84' fill up pipe every 0 stands. age 16/92

17 12/26/ :0 12/26/ :00 12/26/ :00 12/26/ :00 12/26/ :00 12/26/ :0 12/26/ :0 12/26/ :00 12/2/ :0 12/26/ :00 12/26/ :00 12/26/ :00 12/26/ :00 12/26/ :0 12/26/ :0 12/26/ :00 12/2/ :0 12/2/2014 Drilling & Completion Summary - Ascending 0.5 LAN EQUI RIGSER Rig service. 2 ROD-TRI TRI TRI TI from 4,84' to,50' fill up pipe every 0 stands 2 LAN EQUI DIE ick up 5'' drill pipe & TI from,50' to 8,150'. Install rotating head. 1 ROD-CIRC CIRCULATE CIRC Displace hole with 8.ppg OBM mud, swap over to the shakers. 0.5 ROD-DRILL CURVE 4 ROD-DRILL CURVE 0.5 ROD-DRILL CURVE 6.5 ROD-DRILL CURVE.5 ROD-DRILL CURVE DRILL CURVE- DRILL CURVE- DRILL CURVE- DRILL CURVE- DRILL CURVE- Report #: 1 Daily Operation: 12/2/ /28/2014 ORIG DRILLING rimary Job ODR Days rom Spud (days) Days on Location (days) End Depth (ftkb) End Depth (TVD) (ftkb) , ,.0 Built curve 849' to 880' 14.8 fph); 84% complete; 100% sldg. Rig Service. Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: 18:0 12/21/2014 Released Rig RIG NT: 0 hours for previous 24 hrs., 24 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 100% Intermediate drilled, Completion ercentage: 84% roduction curve drilled. Water 11 bbls Used 11 bbls Total used: 5689 bbls DRL CURVE- DRL CURVE- DRL CURVE- DRL CURVE- DRL CURVE- Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 Notified Texas RRC 19:08hrs to Run 9 5/8 csg to 8140' & cement Spoke to Cindy, Operator #4 No accidents, Incidents or spills reported last 24hrs loat 8,18' loat 8,045' 8809` MD_8.2 INC_1.86 AZM_852' TVD_DLS: 5.0_100' /Center 8808: 90% S, 10% LS 12/2/ /2/ :00 Dens Last Mud (lb/gal) 8.60 Rotate from 8150' to 8209' 118 fph)., WOB 20k, 5 rpm, S 1240, motor diff 150, 6 GM, torque 9k. Slide from 8209' to 824' 16. fph). 18L GT, WOB 5k, S 1155, motor diff 220, 6 GM, torque 0k. Rotate from 824' to 8290' 2 fph)., WOB 10k, 5 rpm, S 1450, motor diff 450, 6 GM, torque 9k. Slide from 8290' to 8428' 21.2 fph). 180L GT, WOB 5k, S 180, motor diff 220, 44 GM. Slide from 8428' to 849' 18.6 fph). WOB 9k, S 115, motor diff 185, 400 GM. Rig &, 6 DRILL CURVE- 8 ROD-DRILL CURVE DRL CURVE Slide from 849' to 8620' 15.9 fph). WOB 20k, S 2050, motor diff 280, 550 GM. age 1/92

18 12/2/ :00 12/2/ :0 12/28/ :00 12/2/ :0 12/28/ :00 12/28/2014 Drilling & Completion Summary - Ascending 0.5 LAN EQUI RIGSER Rig service. 9.5 ROD-DRILL CURVE 6 ROD-DRILL CURVE DRILL CURVE- DRILL CURVE- DRL CURVE- DRL CURVE- Slide from 8620' to 884' 1. fph). WOB 22k, S 2140, motor diff 165, 546 GM. Slide from 884' to 8841' 9.5 fph). WOB 25k, S 1525, motor diff 1, 46 GM. Report #: 18 Daily Operation: 12/28/ /29/2014 ORIG DRILLING rimary Job ODR 0402 Days rom Spud (days) 16 Days on Location (days) 18 End Depth (ftkb) 8,904.0 End Depth (TVD) (ftkb) 8,822.5 Dens Last Mud (lb/gal) 8.60 Rig &, 6 Slide from 8841' to 8904' fph). CBU, OO due to build rates 8904' to 100'. Change out BA. TI 100'- 000' with BA #6 ART Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: 18:0 12/21/2014 Released Rig RIG NT: 1.5 hours for previous 24 hrs., 25.5 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 100% Intermediate drilled, Completion ercentage: 6% roduction curve drilled. Water 11 bbls Used 0 bbls Total used: 5689 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 Notified Texas RRC 19:08hrs to Run 9 5/8 csg to 8140' & cement Spoke to Cindy, Operator #4 No accidents, Incidents or spills reported last 24hrs loat 8,18' loat 8,045' 8851` MD_41.4 INC_1.46 AZM_884' TVD_DLS: 5.2_100' /Center 8808: 80% S, 10% LS, 10% SD 12/28/ /28/2014 0:0 12/28/ :0 12/28/2014 1:00 12/28/ :00 12/28/ :00 12/28/ :0 12/28/2014 0:0 12/28/ :0 12/28/2014 1:00 12/28/ :00 12/28/ :00 12/28/ :0 12/28/ : ROD-CIRC CIRCULATE CIRC Slide from 8841' to 8850' 6 fph). WOB 20k, S 1900, motor diff 250, 450 GM. 1 ROD-CIRC CIRCULATE CIRC Wait on orders from drilling engineer & geology, decision made to continue drilling and monitor motor yields. 4.5 ROD-DRILL CURVE DRILL CURVE- DRL CURVE- Slide from 8850' to 88' 5.1 fph). WOB 20k, S 1900, motor diff 250, 450 GM. 1 UNLAN EQUI U_RIG Change out leaking swivel packing on top drive. 1 ROD-DRILL CURVE DRILL CURVE- DRL CURVE- 0.5 LAN EQUI RIGSER Rig Service Slide from 88' to 889' 6 fph). WOB 20k, S 1900, motor diff 250, 450 GM. 0.5 UNLAN EQUI U_RIG Replace "O" ring in goose neck age 18/92

19 12/28/ :00 12/28/ :00 DRILL CURVE- 2 ROD-DRILL CURVE DRL CURVE- Slide from 889' to 8904' 12.5 fph). WOB 25k, S 1650, motor diff 250, 460 GM. Decision made to OO due to build rates. 12/28/ :00 12/28/ :00 12/29/ :0 12/29/ :00 12/29/2014 0:00 12/28/ :00 12/29/ :0 12/29/ :00 12/29/2014 0:00 12/29/2014 Note: Last survey 8851' MD 41.4 deg 1.46 azim. DLS 5.. DLN to land on line- 1.2 DLN to land 10' low DLN to land 15' low DLN to land 25' low ROD-CIRC CIRCULATE CIRC CBU, ( decision made to OO for build rates), pump 0bbls hi vis sweep, circulate till shakers clean. 4.5 ROD-TRI BA TRI OR BA TRI BA Check flow, well static. ump slug. OO from 8904' to 200' hole slick and taking proper fill. Remove rotating 200' 0.5 LAN EQUI BA Drain mud motor, break off bit. Lay down same. 2 LAN EQUI BA ick up Scientific 2.8deg. adj. /8lobe 5.0stage 0.28rpg mud motor, install MWD. Scribe & test surface tools, all good. Make up ughes 8.5'' GX-28 ( x24's). ROD-TRI TRI TRI Trip in hole rom 100' to 000' with BA #6. ill up every stands. Report #: 19 Daily Operation: 12/29/ /0/2014 ORIG DRILLING rimary Job ODR Days rom Spud (days) Days on Location (days) End Depth (ftkb) End Depth (TVD) (ftkb) Dens Last Mud (lb/gal) ,12.0 8, TI, Ream /8428' - T/8904', Built curve 8904' to 912' 19 fph); 9% complete; 100% sldg. Rig (& 6), Well (University -4 # 22) Rig started Rigging down & preparing to 1:00 12/11/14 Accepted rig on day work: 1:00 hrs 12/12/2014 Spud 18:0 hrs 12/12/2014 Surface TD: 09:00 12/1/ :0 12/15/2014: 18:0 12/21/2014 Released Rig RIG NT: 0 hours for previous 24 hrs., 25.5 hours for the month of December 2014 Completion ercentage: 100% Surface hole drilled Completion ercentage: 100% Intermediate drilled, Completion ercentage: 9% roduction curve drilled. Water 496 bbls Used 8 bbls Total used: 656 bbls Note: Notified Texas RRC 12/11/14 with intent to spud well and run and cement 1 /8'' casing. Operator: Angela, Operator # 6 Notified Texas RRC 08:46 hrs to Run 1 /8" csg to 1,859' & cement Spoke to Linda, Operator # 8 Notified Texas RRC 19:08hrs to Run 9 5/8 csg to 8140' & cement Spoke to Cindy, Operator #4 No accidents, Incidents or spills reported last 24hrs loat 8,18' loat 8,045' 902` MD_68.46 INC_16.1 AZM_8914' TVD_DLS: 16.60_100' /Center 9100': 90% S, 10% LS 12/29/ /29/ :00 12/29/ :00 12/29/ :00 Rig &, ROD-TRI TRI TRI TI from 000' to 8428' fill up pipe every 0 stands 4 ROD-CIRC CIRCULATE CIRC ole taking on 8428', pipe will no go down on elevators. Wash down 8428' to 8904' age 19/92