Tension / Compression tap chucks for tapping cycles that are not synchronized

Transcription

1 Tension / Compression tap chucks for tapping cycles that are not synchronize For tapping applications on CNC machines where the revolutions per minute an fee rate are not synchronize to the tap pitch, tap holers with tension / compression float are recommene. These tap chucks rely on the machine spinle for reversal, but by proviing axial float, the tap is able to follow the correct pitch, proucing gage perfect threas. Tapmatic offers a complete program of tension / compression tap chucks with a wie range of sizes, an three ifferent tap holing options. Rubberflex multi range collets, ER collets, or. M Rubberflex Collets Tension / compression floating tap holers for gage perfect threas with releasable har start for consistent tapping epth control. For tap sizes M1.4-M30. Only two collets neee to cover the capacity of each holer. M ER Collets All the same features as the rubberflex version but for use with ER square rive collets. For tap sizes M1.4-M18. ER GB square rive collets inclue an internal square rive for securely gripping the tap shank. TA In aition to tension/ compression an releasable har start, the TA series inclues front release. A safety feature that releases the quick change tap aapter when the extension float is exceee. TIC All the same features as the TA series but with the aition of high pressure internal coolant up to 50 bar. For tap sizes M3-M36. For tap sizes M1-M49. for fast tap change without wrenches NC In aition to tension/ compression an releasable har start, the NC series inclues a unique release to neutral feature that allows you to control tapping epth inepenent of the machine spinle stopping point. NC150 arge capacity ER50 Tension floating tap holer for large sizes with release to neutral. Inclues high pressure internal coolant. For tap sizes M22-M48. For tap sizes M2-M22. 24

2 M tap chucks with moular straight shank an RF collet imensions (MORE) Moel Weight kg M M M M Tapping chuck with increase tension an compression to accommoate tapping cycles that are not synchronize. Features an Avantages n increase tension an compression n releasable har start for consistent epth control n right han an left han tapping n multi-range collets (RF), ajustable back jaw for riving tap square How to Orer Please select the tap chuck an CAT, K or BT shank, to fit your application. Please orer rubber flex collets separately. Moel Orer coe Capacity (steel) hank Collets Tension T Compression H Rubber Flex M M1.4 M7 16mm 21600, #0-1/4" 5/8" No. 2 Morse M M3 M12 20mm 22100, #6-1/2" 3/4" No. 2 Morse M M5 M18 25mm 24100, #10-3/4" 1" No. 3 Morse M M10 M30 32mm 26100, /2" - 1 1/8" 1 1/2" No. 3 Morse No. 4 Morse Note: Aitional shanks available. When using roll form taps, the tool capacity must be reuce 25%. tap chucks with moular straight shank an ER collet Tapping chuck with increase tension an compression to accommoate tapping cycles that are not synchronize. imensions Moel Weight kg M M M Features an Avantages n increase tension an compression n releasable har start for consistent epth control n right han an left han tapping n ER steel collet chuck How to Orer Please select the tap chuck an CAT, K or BT shank, to fit your application. Please orer ER steel collets separately. Moel Orer coe Capacity (steel) hank Collets Tension T Compression H M ER M1.4 M7 16mm ER ER #0-1/4" 5/8" M ER M3 M12 20mm ER ER #6-1/2" 3/4" M ER M5 M18 25mm ER ER #10-3/4" 1" Page 50 Page 44 Pages teep Tapers RF Multi-range Collets teel collets pee Chart 25

3 TA tap chucks with moular straight shank an quick change imensions Moel 2 TA TA TA TA TA TA TA2-032 TA TA tap chucks with morse taper an quick change TA tapping chuck with tension/compression. With its quick change spinle the taps can be change in secons. Features an Avantages n tension an compression n releaseable har start for consistent epth control n front release protects against amage if over extene n right han an left han tapping n short projection How to Orer Please orer the tap chuck an CAT, K or BT shank to fit your application. Please orer tap aapters separately Moel Orer coe Capacity (steel) hank Aapter Tension T Compression H Front relase TA M1 M10 16 mm Nr TA #0-1/4" 20 mm Nr TA M3 M14 16 mm Nr TA #8-9/16" 20 mm Nr TA mm Nr TA M4.5 M24 25 mm Nr TA /16" - 7/8" 32 mm Nr TA M14-M36, 13/16" - 1 3/8" 32 mm Nr TA M22-M48, 7/8" - 1 7/8" 40 mm Nr Note: When using Roll Form Taps the chuck s tapping capacity must be reuce by 25 %. 2 How to Orer Please select the tap chuck to fit your application. Please orer quick change tap aapters separately. imensions Note: When using Roll Form Taps the chuck s tapping capacity must be reuce by 25 %. All imensions are shown in mm. 25.4mm = 1" 2 Moel 2 TA0-MT TA0-MT TA1-MT TA2-MT TA3-MT TA4-MT Moel Orer coe Capacity (steel) Morse taper MT Tap aapters Tension T Compression H Front release TA0-MT1 490MT1 M1 M10 1 Nr TA0-MT2 490MT2 #0 1/4" 2 TA1-MT2 491MT2 M3 M14 2 Nr TA1-MT3 491MT3 #8 9/16" 3 TA2-MT3 492MT3 M4.5 M24 3 Nr TA2-MT4 492MT4 5/16" 7/8" 4 TA2-MT5 492MT5 5 TA3-MT4 493MT4 M14 M36 4 Nr TA3-MT5 493MT5 13/16" 1 3/8" 5 TA4-MT5 494MT5 M22 M48 5 Nr TA4-MT6 494MT6 7/8" 1 7/8" 6 Page 50 Pages teep Taper Quick-Change Aapters pee Chart

4 TIC tap chucks with moular straight shank, quick change an internal coolant IC 2 Tapping chuck with internal coolant system, tension, compression an quick-change spinle, where the tap can be change in secons. Features an Avantages n tension an compression n releaseable har start for consistent epth control n front release protects against amage if over extene n right han an left han tapping n internal coolant system (max. 50 bar) n short projection How to Orer Please orer the tap chuck an CAT, K or BT shank to fit your application. Please orer tap aapters separately. imensions Moel mm mm mm 2 mm TIC TIC TIC Moel Orer coe Capacity (steel) hank Aapter Tension T Compression H Front release TIC C1025 M3 M14, #8-9/16" 25 Nr TIC C2025 M4.5 M24, 5/16" - 7/8" 25 Nr TIC C3032 M14 M36, 13/16" - 1 3/8" 32 Nr Note: When using Roll Form Taps the chuck s tapping capacity must be reuce by 25 %. tap chucks with HK shank, quick change an internal coolant IC How to Orer Please select the tap chuck to fit your application. Please orer quick change tap aapters separately. 2 imensions Moel 2 TIC1-HK50A TIC1-HK63A TIC1-HK80A TIC1-HK100A TIC2-HK50A TIC2-HK63A TIC2-HK80A TIC2-HK100A Moel Orer coe Capacity (steel) hank HK-A Aapter Tension T Compression H Front release TIC1-HK50A 49C1H50 M3 M14 50 Nr TIC1-HK63A 49C1H63 #8-9/16" 63 TIC1-HK80A 49C1H80 80 TIC1-HK100A 49C1H TIC2-HK50A 49C2H50 M4.5 M24 50 Nr TIC2-HK63A 49C2H63 5/16" - 7/8" 63 TIC2-HK80A 49C2H80 80 TIC2-HK100A 49C2H Note: When using Roll Form Taps the chuck s tapping capacity must be reuce by 25 %. All imensions are shown in mm. 25.4mm = 1" Page 50 Pages teep Taper Quick-Change Aapters pee Chart 27

5 NC tap holers with self fee an release to neutral The NC eriestools inclue a unique feature which allows you to control the tapping epth inepenent of the stopping position of the machine spinle. When the fee is pause with the spinle of the machine still rotating, the tap will continue into the hole for a short "self fee" istance, extening the tension float of the tap holer. Once this position is reache the rive of the tap holer releases an the tap stops. The machine spinle can then be stoppe, reverse an retracte. The release feature is an accurate way to control tapping epth in blin holes an can be use on both CNC controlle machines or even on conventional machines where the operator is controlling the fee. tap chucks with moular straight shank, quick change an release to neutral Tapping chuck with quick change spinle an self-release. (B) Features an Avantages n tension compression n releasable har start for consistent epth control n self-release for precise epth control inepenent of machine spinle stop n quick-change version for fast tap changes without any wrenches How to orer Please select the tapping chuck an CAT, K or BT shank (B), to fit your application. tanar aapters shown in accessories section. NC Tapping Chuck with traight hank, Quick-Change Aapter Moel Orer coe Capacity (steel) hank Aapter ize Weight kg elf-fee self-release Compression NC M2 M6 20 mm Nr #4 1/4 3/4 NC M3 M12 25 mm Nr #8 9/16 1 NC M5 M22 25 mm Nr /16 7/8 1 NC150 large capacity, tension float with release to neutral an internal coolant system COOANT NC150 Tapping Chuck with traight hank, ER50 teel Collet, Internal Coolant ystem Moel Orer coe Capacity (steel) hank Collets Weight kg elf-fee self-release NC M22 M48 40 mm ER (B) Page 50 Page Pages teep Tapers Quick-Change Aapters teel collets