Adams. Progressive. Description. Typical system layout using Pneumatic Pump for grease - with monitoring. Typical system
|
|
- Arthur Cameron
- 5 years ago
- Views:
Transcription
1 45 P rogressive systems can be used for oil or grease lubrication when it is required to provide a positive displacement with visual or electrical monitoring. ll outlets can be checked by one indicator rod or electrical switch. range of automatic control timers and monitors are available.
2 46 escription centralized lubrication system is described as when it contains metering pistons, which can operate in a sequence thereby giving measured amounts of lubricant to each lubrication point. s each piston in a distribution block is moved it opens the passageway for the following piston which can therefore distribute pre-determined amounts. ach lubrication point receives a measured amount of lubricant and this can normally be varied by changing the values of the individual metering screws. s each metering piston is put in series with all the other pistons, any blockage to the lubrication point results in the whole system being stalled. This stalling of the system enables the operator to visually check the system, or else micro switches can be fitted to enable the checking process to take place automatically. range of programme controllers is available for this purpose. Lubricants: Oils up to 2000 cst/40 and greases up to grade 2 (NLGI) Typical system layout using Pneumatic Pump for grease - with monitoring Typical system
3 47 istributors Monoblock Type Operating sequence 1. In (), supply pressure through internal passages moves piston 3 left, while pistons 1 and 2 are positioned to the left. 2. In (), piston 3 bottoms, it opens internal passages directing supply pressure to the left end of piston 1. Lube discharges from port In () piston 1 bottoms. It opens internal passages directing supply pressure to the left end of piston 2 which returns to its initial position as lube discharges from port The sequence continues, positioning the piston 3 to the right and the piston 1 to the left. Lube discharges from port 4, then 6. Modular Type The main feature of this series is that the upper section of the distributor, which contains all of the working parts, is detachable from the lower part which is fixed to the machine and accommodates all of the pipe connections. This design allows all the inlet and outlet pipework to be installed with the knowledge that it will remain undisturbed in the event of a metering section requiring replacement. It requires only the removal of 4 screws to detach the metering section of the distributor.
4 48 istributors Monoblock Type - Material: Monel Part No. Series and L Outlet cc/outlet No. of Outlets LV LV /16 N to LV PS LV LV LV /8 SP to LV PX LV LV LV /4 SP to LV PZ LV Variations in output are controlled by metering screws, which have a number stamped on their heads to indicate value. See chart below. L PS 1/8 SP PX 1/4 SP PZ 3/8 SP PS PX PZ Marking cc/ycle Marking cc/ycle Marking cc/ycle TS TX TZ TS TX TZ TS TX TZ TS TX TZ PX12 Modular Type - Material: ase - Steel, istributor ody - Monel Part No. Series and L Outlet cc/outlet No. of Outlets LV LV /16 N LV MS to LV LV LV /8 SP LV MX to LV PS 1/8 SP PX 1/4 SP PZ 3/8 SP Preferred Ranges are as shown above, istributors with a larger number of outlets are available to special order. L Tube ittings for Inlet & Outlets:- LV Tube Nut for 4mm O/ (5/16 N) LV Tube Nut for 6mm O/ (1/8 SP) LV Tube Nut for 8mm O/ (1/4 SP) LV Tube Nut for 10mm O/ (3/8 SP) LV Sleeve for 4mm O/ LV Sleeve for 6mm O/ LV Sleeve for 8mm O/ LV Sleeve for 10mm O/
5 49 ccessories for istributors locks Visual Indicator Rod - Suffix Micro Switch and Rod - Suffix MH Proximity Switch and Rod - Suffix MY Reed Switch and Magnet - Suffix M or Metering Screws for above Range - sk for ata Sheet Overpressure Indicators Memory Type - Pin stays out until re-set Part No. LV LV LV LV LV LV LV Pressure 25 bar 40 bar 60 bar 90 bar 120 bar 150 bar 200 bar urst Type Indicators This indicator consists of a bursting disc only which breaks in case of abnormal high pressure and causes the lubricant to flow away. In this case the system goes on working. Part No. LV LV LV LV LV LV reakage Pressure 60 bar 90 bar 120 bar 150 bar 200 bar 240 bar urst Type Memory Type Single or ombined outlets and Multi-delivery. See ata sheets for details
6 50 ombined Motorised Grease Pump & ontrol Timer for Grease up to NLGI Grade 2 esigned to supply grease lubrication systems with progressive distributors to provide manual or automatic cyclic lubrication. Intermittent operation only, duty must not exceed 25% of the total period. Three types available, see table. Specification Output: 2.4 cc per minute Operating Pressure: 120 bar Maximum Pressure: 200 bar Outlet Port: 1/4 SP Reservoir: 1.5 kg capacity filled via grease nipple Low Level Switch: P.N.P. N Proximity supplied fitted as standard. Operating Voltage: vailable with 12 & 24 Volts, and 12, 24, 100 or 230 Volts Please state voltage required when ordering. Insulation Protection: IP 55 Operating Temperature: Lubricants: Liquid and /or grease up to NLGI grade 2. Type L lectrically operated without timer Part No. No of OutletsOutput/Min Reservoir ap. Low Level ontrol nd ycle LV cc 1.5 kg Yes No No Type L lectrically operated with P timer Part No. No of OutletsOutput/Min Reservoir ap. Low Level ontrol nd ycle LV cc 1.5 kg Yes Yes No Type L lectrically operated with P timer and end of cycle control Part No. No of OutletsOutput/Min Reservoir ap. Low Level ontrol nd ycle LV cc 1.5 kg Yes Yes Yes
7 51 imensional etails ombined Motorised Grease Pump, Timer & istributor Type L lectrically operated with P timer, end of cycle control plus distributor. Part No. No of Outletslow Rate Per Point Per ycle LV LV LV LV cc LV LV LV
8 52 Manual Oil & Grease Pumps - Type PM (Oil) & PMK (Grease) Part No. G or ull mpty Thread Use With LV /8 Oil LV SP Grease apacity 300cc. 1cc/stroke elivery. Pressure 100 bar. Heavy uty Manual Pumps- ouble cting Type PMK G Part No. Reservoir G Lubricant apacity Lt. Thread LV Oil LV / cst LV SP Grease up to LV Grade 2 (NLGI) apacity 2.5 Lt & 5 Lt. elivery Pressure 150 bar G Mechanical Oil Pump - Type PPR Part No. G H J LV Oil 5mm stroke cc. Motorized Oil Pump & Reservoir - Type PRQ V 3 Phase 50 Hz. Pressure: 70 bar Max. Intermittent uty Only Output 180 cc/min elivery Pressure bar M12x1 M10x1 J H G G Part No. Reservoir G H J L M apacity Lt. LV LV LV LV H J 1/4 SP Materials: 2.7 Lt Reservoir - Plastic 3.0 Lt, 5.0 Lt, 7.0 Lt - luminium M L Motorized Oil Pump (uilt to Order) V 3 Phase 50 Hz. Pressure 70 bar Max. Intermittent uty only Reservoir apacity (cc) H L P H Note:- See ontinuous range for more pumps P L
9 53 Motorized Pump & Grease Reservoir - Type PRK Volt 3 phase 50 Hz Motor Rating 0.25 kw Working pressure up to 300 bar Up to 4 piston outlets available, giving 900cc/outlet Max. each Reservoir capacity 10 kg, 20 kg & 70 kg Ordering xample:- LV asic motorized pump body - 10 kg. (Includes Low level switch LM ) or High/Low level switch add Suffix LX or number of pump outlets add Suffix.1,.2,.3 or.4 Note:- Outlets can be grouped together if required. G Part No. Res. apty. G Thread LV kg 483 LV kg /8 SP LV kg 1000 Motorized Pump & Grease Reservoir - Type NK Pumping elements: from 1 to 3 (to be specified when ordering) elivery: 2.4cc/min each unit Max. pressure: 300 bar Supply voltage: V, or V, or 110 V 50/60 Hz. or 230 V 50/60 Hz Speed of rotation: 18 rpm Reservoir capacity: kg (both plastic) Low level switch: Proximity PNP N Logic Included as standard illing: 1/4 SP industrial grease nipple Lubricants Oil: ny type and viscosity Grease: 000 to 2 (NGLI) G Part No. Res. apty. G Thread LV kg 340 LV kg /4 SP With Integral Timer - Intervals 15 to 120 mins - Lubetime 1 to 8 mins LV kg 340 LV kg /4 SP Pneumatic Grease Pump & Reservoir - Type PS Single Outlet giving up to 2cc per stroke (also versions up to 0.8 and 4cc - refer to sales office) Operating pressure: Grease / ir ratio Max. pressure 150 bar Single acting air cylinder - 4 to 8 bar air pressure lso available with plastic reservoir. Low level switch included as standard Part No. Res. apty. G Thread LV kg /4 SP LV kg 420 G T or ouble cting Pumps, also Pumps without Reservoirs - Please refer to sales office. ll Pumps will handle Grease up to NLGI Group 2. Pump output is controlled by Metering Screws fitted at point T. Steel Reservoir Shown
10 54 ccessories for Systems Timers or our full range of Timers - please see page 20 Pressure Gauges - ack fitting ottom itting Part No. T Taper ar MPa LV /8 SP LV LV /4 SP LV T Part No. T Taper ar MPa LV /8 SP LV LV /4 SP T Non-return Valves Part No. a/f irection of low from LV /8 SP 3/8 SP 9.5 to LV to /8 SP 1/8 SP 10 LV to ilters - Suction Type Part No. Thread Mesh Lt/Min LV M10x1 0.5 LV M12x LV M18x LV /8 SP LV / LV / LV LV Large apacity Part No. Thread Mesh Gauze + Magnet LV LV /8 SP LV LV /2 SP LV LV LV LV /4 SP Line Type - for oil Part No. L Thread Micron LV /2 10 LV SP 25 Pressure Rating 110 bar - vailable with Visual, lectric or lectro/visual Indicators Line Type - for grease Part No. Thread Micron Pressure LV /8 SP LV /4 SP bar LV /8 SP LV bar Pressure Regulators - or oil Part No. Pressure Range (ar) nominal Mounting LV /4 SP 1/4 SP Line Type LV /8 SP 3/8 SP LV M10x Lock Nut M20 Reservoir Type LV M12x1 Models LV and LV are intended for mounting through reservoir top plates.
PNEUMATIC RACK AND PINION ACTUATORS. Advanced torque to size ratio
PNUMTI RK N PINION TUTORS dvanced torque to size ratio eatures: Pneumatic Rack and Pinion ctuators 90 ctuation for -way valves (Straight & ngle) 180 ctuation for -way (T-type) valves ctuators comply with
More informationGREASE NLGI (*) OIL CST (*) PRESSURE (220.5) (147) - 20 (294) (220.5)
CHARACTERISTICS THREE TYPES OF THREADING AVAILABLE: BSP, NPTF, SAE : UP TO 500 BAR : UP TO 400 BAR OIL AND GREASE FUNCTION CE AND ATEX MARKINGS BASES ALWAYS SUPPLIED WITH STANDARD SEALS AND MOUNTING SCREWS
More informationDPL. Monoblock progressive dividers. High quality and High tolerance Unbeatable combination of performance and convenience
Monoblock progressive dividers High quality and High tolerance Unbeatable combination of performance and convenience TL O ONTNTS Description 3 Techinical data 4 Outlets 5 Ordering s 8 Junctions 9 Shut-Off
More informationlubrication systems PEGPEO 5N-10N-25N-210N pumps for progressive systems
lubrication systems PEGPEO 5N-10N-25N-210N pumps for progressive systems TABLE OF CONTENTS TABLE OF CONTENTS 2 Applications and operation 3 Technical data Operation 4 Tank 4 PEG-PEO 5N/10N/SM Electric
More information501 SERIES. 501 Series Directional Control Valve Platform. Featuring Higher Flow in a Compact Valve Package. Commissioning Capabilities
501 Series irectional ontrol Valve Platform Featuring Higher Flow in a ompact Valve Package ommissioning apabilities Solenoid air pilot actuated Low wattage.8 wall for application solenoids Polarity insensitive
More informationSpring Return and Double Acting Pneumatic Quarter- Turn Actuators For Output Torques to 13,444 lb.in.
Spring Return and ouble cting Pneumatic Quarter- Turn ctuators For Output Torques to 13,444 lb.in. Features and benefits ompact rack and pinion design utilizes the whole piston area to develop output torque.
More informationISO Standard Hydraulic Cylinder
ISO Standard ydraulic ylinder Series S/SG Series S Q N Nominal pressure: S Pa ore size :,,,, Related quipment Series SG Nominal pressure: - Pa ore size : 3,,,,, 51 ISO Standard ydraulic ylinder Series
More informationA system of lubricant dispensing devices (oil or grease) connected by piping to a central pumping unit that is operated automatically or manually.
Air/Oil Systems: A lubrication system in which small measured quantities of oil are introduced into an air/oil mixing device which is connected to a lube line that terminates at a bearing, or other lubrication
More informationHusky 1050e Pumps Electric Double Diaphragm
usky 15e Pumps lectric ouble iaphragm Selector Tool To order a usky 15e, use the online selector tool at www.graco.com/pumpselectors or contact your distributor. NOT: heck the identification plate (I)
More informationFITTINGS AND ACCESSORIES
INDEX Application examples and general notes... Page 2 General description... Page 3 Modular SMX SMX... Page 7 Monitor of piston movement: by a reed Switch and micro switch... Page 15 by inductive proximity
More informationELECTRIC GREASE AND OIL PUMPS ILC-MAX
ELECTRIC GREASE AND OIL PUMPS ILC-MAX ELECTRIC GREASE AND OIL PUMPS - ILC-MAX 24 ELECTRIC GREASE (ILC-MAX-G) OIL (ILC-MAX-O) PUMPS HOW TO ORDER 40.2.24AC.FST.G TANK 2 = 2 Kg transparent 4 = 4 Kg transparent
More informationSureFire SLR Lubricator
Sureire SR ubricator utomatic, Oil eneral he Sureire SR automatic lubricator is a robust and durable pump that can handle oil and soft greases. Its compact size is designed to fit your space requirements
More informationISO Standard Hydraulic Cylinder
IO tandard ydraulic ylinder eries / eries eries Nominal pressure: a ore size :,,,, Q N Related quipment - Nominal pressure: a ore size : 3,,,,, 4 IO tandard ydraulic ylinder eries Nominal pressure a/ a
More informationAUTHORIZED DISTRIBUTOR DPX PROGRESSIVE DIVIDERS
1 DESCRIPTION Ilcolube is the lubrication system which identifies distribution and dosing with a progressive movement of pistons that are. Controlled one by the other in an interdependent sequence. This
More informationThe BVA Advantage. Confidence Built on Quality
1 The V dvantage V Hydraulics was launched in 2003 and is centrally located in the United States in Kansas ity, Missouri. V is one of the Shinn u of merica ompanies including; Hein-Werner, Omega Lift,
More informationhydraulic power clamps
ourtesy of M/Flodyne/ydradyne Motion ontrol ydraulic Pneumatic lectrical Mechanical (8) 426-548 www.cmafh.com hydraulic power clamps Table of ontents ydraulic lamping 1-21-4 1-21-51 1-21-72 1-211-2 1-211-4
More information503 Series Solenoid Pilot Actuated Valves
Solenoid Pilot ctuated Valves Offered by: Specialists in Valves, ontrols, Pneumatics, Fluid Measurement Phone: (203) 261-6711 www.okcautomation.com 5 Ported, 2 and 3 position, 4-way, Spool & Sleeve and
More informationSelection table. Manually operated pumps. Electric driven mini pumps. Air driven single stage pumps. Air driven two stage pumps
INX PUMPS Hydraulic Pumps Selection table 22 HP Range Manually operated pumps 23 HP Range General information on electric driven pumps 24 HP1 Range lectric driven mini pumps 24 HP3 Range lectric driven
More informationZEM Injector. Series 32, 33, 34, 35, 39. General. Operation. Features. Technical Data. Injector Outputs R2 08/10
ZEM Series 32, 33, 34, 35, 39 General The ZEM Series injector line are positive displacement injectors (PDI) that deliver precise and controlled lubrication outputs which meet exact requirements for diverse
More informationPVL Series. Solenoid & Remote Pilot Operated 1/8" & 1/4" Valves. Section C. C59
Series Solenoid & Remote Pilot Operated /8" & /4" Valves Section Moduflex www.parker.com/pneu/pvl asic Valve unctions...60 Stacking pplications...6-62 eatures ( & )...63 ommon Part Numbers-Stacking ( &
More informationHow to Order. Nil M. Action S T. Load voltage Wiring. M9NV 5 V, 12 V 3-wire (PNP) M9PV 12 V. F9NWV 5 V, 12 V 3-wire (PNP) F9PWV
ompact ylinder: Standard Type Single cting, Single Rod, Spring Return/Extend Series QS ø, ø, ø, ø How to Order QS S QS S FWV S uilt-in magnet Mounting style Through-hole/oth ends tapped common (Standard)
More informationHydraulic Systems Hydraulic Clamping
ydraulic Systems 19. 1 ydraulic lamping Page ydraulic lamping Page 1-21-4 1-21-51 1-21-72 1-211-2 1-211-4 1-211-52 1-211-54 1-212-4 19.2-19.3 3-1-S-475 3-1--475 19.6 52-Series 19.3 3-1-S-11 19.7 3-1--11
More informationTable of Contents. Numatics 2009 Rev. 1/09
Table of ontents RW Series...-8 eatures and Benefits... How To Order... Replacement omponents... imensions... 5 Technical Specifications... 6 Switch Information....7-8 Numatics 2009 Rev. /09 2 RW-Series
More informationTOX -Powerpackage X-KT-System
TO -Powerpackage -KT-System The pneumohydraulic split system ata sheet 0.05 08 / 06 TO GmbH & Pressotechnik o. KG Riedstrasse 8850 Weingarten / Germany Find your local contact at: TO -Powerpackage -KT-System
More informationWaterPumps QH QV QVK
WaterPumps Q QV QV Introduction IRON Pump /S was founded in 10 and since then the company has manufactured a great variety of pumps covering both the marine and industrial markets. Through the years the
More informationISO Standard Hydraulic Cylinder
IO tandard ydraulic ylinder eries / eries eries Nominal pressure: a ore size :,,,, Q N Related quipment - Nominal pressure: a ore size : 3,,,,, ourtesy of teven ngineering, Inc.- Ryan Way, outh an rancisco,
More informationBVA Limited Lifetime Warranty
1 The V dvantage V Industrial Hydraulics was launched in 2005 and is centrally located in urope in tten-leur, The Netherlands. V is one of the Shinn u urope brands besides Omega Lift, Omega Mechanix and
More information1 Cylinder. 1 - Cylinder Type 3 - Cylinder Capacity 4 - Cylinder Stroke. 2 - Cylinder Options. Cylinder Accessories
1 Type 30 06 T 2 3 4 5 apacity Stroke Options ode 1 - Type 3 - apacity 4 - Stroke ydraulic 2 - Options L LN LN P P T U U U ULN S/ - ollow ole / - eneral Purpose / - ollow ole / - igh Tonnage S/ - lat ody
More informationSeries 25A-CJ2. Air Cylinder: Standard Type Double Acting, Single Rod. ø10, ø16 25A. How to Order. Auto switch mounting type
Series -J2 ø0, ø6 magnet for switch, auto switch cannot be mounted. E M asic ouble-side bossed ouble clevis Single foot ouble foot ore size 0 0 mm 6 6 mm J2 6 60 Z M9W bracket is shipped together with
More informationIndex MANUAL SPRING MOTOR EXTRAS. +44 (0) or visit Fuel Hose Reels. Fuel Hose Reels. Fuel Hose Reels.
Index SPRIN L ompact Hose Reels Hose I.. 6 mm - 10 mm Pressure 21 R P Performance Hose Reels Hose I.. 6 mm - 12 mm SH, MP & HP Heavy uty Hose Reels Hose I.. 6 mm - 19 mm Pressure 350 R Pressure 350 R T
More informationPin Cylinder. Series CJP. Double Acting/Single Acting Spring Return. Standard Variation Built-in Magnet. Single Rod. Single Rod Spring return
Pin Cylinder eries ouble cting/ingle cting pring Return Variations eries tandard tyle eries With uto witch ouble cting (Non-lube) ingle cting (Non-lube) ction ingle Rod ingle Rod pring return tandard Variation
More informationElectric pump EP-1. Electric pump with 1.9 kg reservoir:
The BEKA-MA central lubrication pump model EP-1 is electrically actuated and has up to a maximum of independently operating lubricant outlets. A separate pump element is required for each outlet. Three
More informationHydraulic pump HP-1. Type 1. Type 2
The BEKA-MAX central lubrication pump model HP-1 is hydraulic actuated and has up to a maximum of independently operating lubricant outlets. A separate pump unit is required for each outlet. Three pump
More informationYour Global Source for Today s Most Popular Solenoid Valves
lcon Solenoid Valves Your Global Source for Today s Most Popular Solenoid Valves lcon Solenoid Valves Your Global Source for Today s Most Popular Solenoid Valves lcon Solenoid Valves, a division of International
More informationPiston Accumulators Series Catalog HY /US Page
Page Series 5000 Series 5000 Piston ccumulators Heavy uty Service with 5000 PSI Operating Pressure 2" thru 9" ores with Over 30 Standard apacities Patented V-O-ring Piston Seals Serviceable Threaded End
More informationhydraulic power clamps
hydraulic power clamps Table of ontents lick Page # View ydraulic lamping Page M-Y-# ydraulic lamping Page M-Y-# 1-21-4 1-21-51 1-21-72 1-211-2 1-211-4 1-211-52 1-211-54 1-212-4 3-4 3-1-S-475 3-1--475
More informationTEPHEN TEPHEN LUBRICATION LUBRICATION SYSTEMS
LURITION SYSTMS LURITION LURITORS N OILRS LURITION QUIPMNT PROUT RNG rip Feed Lubricators range of gravity and forced feed oilers for lubricating single or multiple points and for use in conjunction with
More informationAPCO CVS-6000/6000A SWING CHECK VALVES
ULLTIN 00/579 JUN 2016 PO S-00/00 SING K LS PO S Swing heck s are recommended for clean and dirty services such as ater, Sewage or Industrial applications. S-00/00 Swing heck s are a heavily constructed,
More informationlubrication systems CME Electric pump for oil and soft grease volumetric
lubrication systems CME Electric pump for oil and soft grease volumetric lubrication systems TABLE OF CONTENTS Table of contents 2 Description and technical data 3 Operation and technical data 4 Technical
More information% lighter. Air Cylinder. New. New RoHS. 1.31kg. Series CA2. Reduced weight by changing the shape of the rod cover and head cover.
ir ylinder Ø 40, Ø 50, Ø 63, Ø 80, Ø 100 Reduced weight by changing the shape of the rod cover and head cover. Weight reduced by up to New RoS 15 (Ø 50-50 stroke) % lighter 1.31kg New 1.54 kg Existing
More informationFlame hardening steel. The height from the reference hole to the surface of the reference support block can be selected from 2 types HIGH or LOW.
is separated from the reference. INFORMTION Responses to reduction of spare parts, short lead times, and a drastic reduction of special orders Pin Plate ylinder ( machinable type) 1 HIGH type Flame hardening
More informationpump for all, all for pump KSQ9001:2009/ISO9001:2008 A-RYUNG AR2016-AMGP-EK2
pump for all, all for pump KSQ9001:2009/ISO9001:2008 A-RYUNG www.aryung.co.kr AR2016-AMGP-EK2 Oil Lubrication pumps CONTENTS Technical data 3 Resistive Oil supply system 4 Measuring Oil supply system 5
More informationPin Cylinders. Series CJP2/CJP. 2 auto switches can even be mounted on a cylinder with ø4 bore size (5 mm stroke). One-touch fitting can be connected.
Pin ylinders eries JP/JP auto switches can even be mounted on a cylinder with ø ( mm stroke). uto switch One-touch fitting can be connected. (Panel mount type) ø One-touch fitting, miniature fitting, and
More informationSeries Variable Displacement Piston Pump
AH Series Variable Displacement Piston Pump AH AH7 AH AH45 KS Geometric Displacement Max. Operating Series Graphic cm 3 /rev Pres. Page Symbol 3 4 5 6 7 8 9 3 4 5 MPa {kgf/cm 2 } AH-F-R--K-S- AH AH45-F-R--K-S-
More informationPMFO AIR/OIL SYSTEM PMFO AIR-OIL PROGRESSIVE MODULAR LUBRICATING SYSTEMS
AIR/OIL SYSTEM AIR-OIL PROGRESSIVE MODULAR LUBRICATING SYSTEMS (BLUE COLOUR ALUMINIUM BASE) The basic design of this system is similar to the PMF progressive, but with the inclusion of airways to enable
More informationREV lubrication systems PEGPEO Electropumps for progressive systems
lubrication systems PEG/PEO 520-540 - 580 PEGPEO 520-540-580 Electropumps for progressive systems INDEX OF CONTENTS Applications and description 3 Technical data 4 Reservoir 5 Electric motor 6 Electropump
More information3000 psi (207 bar) Output/ min. 115 VAC 10cc (0.61 cu. in.) 24 VDC 12cc (0.73 cu. in.) Discharge Element Output Port.
MultiPort Lubricator Grease, Injector General The MultiPort Lubricator is an electrically driven multiple outlet lubrication unit design primarily for use with injector systems. The unit includes two pumping
More informationAir Actuated Stainless Ball Valves 2-Piece Stainless Steel, Full Port 1/4 to 2 NPT
ir ctuated Stainless all Valves 2-Piece Stainless Steel, ull Port 1/4 to 2 SRIS eatures Spring Return or ouble cting ctuators ull Port direct mount ISO5211 valve 316 stainless steel body, ball and stem
More informationSection 4 - Selection Procedure. Section 5 - Performance Data. Section 6 - Technical Data
RANGE(S) M Section 4 - Selection Procedure Section 5 - Performance Data Section 6 - Technical Data PUMP RANGE M SECTION 4 MODEL ALL PAGE 1 FEATURES & BENEFITS FEATURE 1. Three basic pump sizes with a capacity
More informationPort Size. Connection G1/8 G 1/4 G 3/8 G 1/2 G 3/4 G 1. Standard nominal flow rate * 3000 I/min I/min I/min I/min I/min.
1/4-1 MXLOW LTRS Made as per SO 5782-1 standard. igh level of condensate seperation. Sturdy construction in aluminium. asy removal/refixing of bowl owl guard for 3/8" & 1/2" Size offered as a standard
More informationHigh Pressure Equipment High Pressure Valves, Fittings and Tubing
igh quipment igh Valves, ittings and Tubing 0,000, 40,000 and psi service igh quipment Company has developed a line of igh products to assure safe and easy plumbing for 0,000, 40,000 and psi. These needle
More informationMonobloc and Sectional Directional Control Valves
Monobloc and Sectional irectional Control Valves 200 - - 991210 - - 03/09.2015 1/220 8 Sectional directional control valves HS11 8 valves... p.101 Contents 8.1 General specification 101 8.2 imensional
More informationPeople, Capabilities and Systems to Save Money and Increase Productivity
People, Capabilities and Systems to Save Money and Increase Productivity We re the largest and most successful company in our field because we continually satisfy our customers with the world s best lubrication
More informationSingle Solenoid External Pilot Normally Closed
atalog 000- Operating ressure Internal ilot Solenoid Valves 3/" & 3/" ody 0 to 0 SI (standard) -/" ody to 0 SI (00 SI option available) Series Valves ilot Supply Internal ilot Remote ilot Valve Operating
More informationDPL MONOBLOCK PROGRESSIVE DIVIDERS
HIGH QUALITY HIGH TOLLERANCE 1. E L E A COMBINATION OF PERFORMANCE AND CONVENIENCE I.L.C. srl - Via Garibaldi, 149-21055 Gorla Minore Italy Ph. +39 0331 601697 Fax +39 0331 602001 - www.ilclube.com - info@ilclube.it
More informationPump Autolub-M. Product description APPLICATION PRODUCT CHARACTERISTICS FUNCTION
Pump utolub-m Product description PPLICTION In the sector of plants and machinery: Machine tools, presses, punching machines, shears, hoisting plants, water pumps, etc.. PRODUCT CHRCTERISTICS + Multi-line
More informationLUBRICATION PUMP UCF CENTRAL LUBRICATION
LUBRICATION PUMP APPLICATION Lubrication pumps are used as a source of pressure lubricant for lubricating systems equipped with progressive distributors for permanent, regular lubrication of various machines,
More informationPiston Accumulators Series Catalog /USA Page
atalog 1630-7/US Page Piston ccumulators Series 5000 Series 5000 Piston ccumulators Heavy uty Service with 5000 PSI Operating Pressure 2" thru 9" ores with Over 30 Standard apacities Patented V-O-ring
More informationFill cap with inlet strainer (40 mesh) Automatic approved quick connect inlet (no strainer)
GPO ubricator Motor-driven gear pump, Oil General The GPO ubricator is a motor-driven gear pump that is designed for use with single line centralized lubricating systems utilizing progressive distributors
More informationOPTIONS AUTOMATIC LUBRICATION SYSTEM
OPTIONS AUTOMATIC LUBRICATION SYSTEM The central lubrication of the axes modules consists of a small lubricant dispenser with progressive distributor with several exits. It is responsible for the automatic
More informationEUGEN WOERNER GmbH & Co. KG Postfach 1661 DE Wertheim Am Eichamt 8 DE Wertheim. Pump unit GMZ-E
Pump unit GMZ-E Pump used to supply oil and grease from a barrel directly through a lid-hole or a bunghole. Technical data: Pump with bung-hole Pump with barrel lid Delivery volume per stroke: Pump element
More informationPENMECH LUBRICATION SYSTEMS & EQUIPMENT 27 DOWN GREEN ROAD, HARWOOD, BOLTON, LANCASHIRE BL2 3QD
PENMECH LUBRICATION SYSTEMS & EQUIPMENT 27 DOWN GREEN ROAD, HARWOOD, BOLTON, LANCASHIRE BL2 3QD Tel: 01204 398460 Fax: 01204 398469 Mobile: 07778 421222 Websites: www.penmech.co.uk www.lubetools.co.uk
More informationAir Actuated Ball Valves 3-Piece Stainless Steel, Full Port 1/4 to 3 NPT
ir ctuated all Valves 3-Piece Stainless Steel, ull Port 1/4 to 3 SERIES eatures Spring Return or ouble cting ctuators ull Port direct mount ISO5211 valve Swing-out bolted body design for easy maintenance
More informationLubrication Systems for Vehicles & Plant
MULTI-LINE BEARING REQUIREMENTS & ACCESSORIES TypicaI Bearing Chart Pumping Unit 1. Power Steering Cylinder Front 2. Power Steering Cylinder Intermediate 3. Power Steering Cylinder Rear 4. Track Rod End
More informationELD Series - DC Motor Drive
ELD Series - D Motor Drive ir ooled Oil oolers for Mobile pplications Description These coolers use a combination of high performance cooling elements and long life D electrical powered fans to give extended
More informationFZ-A Lubricator. Electric, Oil & Grease. General. Application. Operation. Features. Adjustment of Discharge Rate R2 03/09
FZ- Lubricator Electric, Oil & Grease General The FZ- Lubricator is primarily designed for direct feed applications for servicing up to 12 lubrication points. The lubricators are supplied with pump bodies
More information1.56 L INEAR A CTUATORS: AIR C YLINDERS S ERIES CA1
1.56 L INEAR A CTUATORS: AIR C YLINDERS A IR C YLINDER Auto switch sensing optional s Ø4, 5, 63, 8, 1 Non-rotating piston rod & double rod types available Ultra low friction, maximum 5% Long life, high
More informationServo-assisted 2/2 way piston valve
Servo-assisted 2/2 way piston valve Type 6240 can be combined with Servo-assisted and compact piston valve with diameter of up to N12 Vibration-resistant, screwed coil system Increased leak-tightness with
More informationSeries RQ. The new standard for the future. Compact Cylinder with Air Cushion. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100
1 Compact Cylinder with ir Cushion ø, ø, ø, ø, ø, ø, ø, ø The new standard for the future J CQ U - NW ir Cushion Cylinder Uses a unique air cushion mechanism with no cushion ring. Size ø, ø and ø newly
More informationLUBRICATION PUMP SAO, SAG
LUBRICATION PUMP APPLICATION Lubricating pump sets, SAO for lubricating oils, and SAG for soft-grease, are used as a source of pressurised lubricant, oil or soft-grease, for single-line central. Lubricating
More informationILC PICO-MAX ELECTRIC GREASE PUMP Automatically Lubricates Small, Medium and Large Machinery
Automatically Lubricates Small, Medium and Large Machinery Programmable Multi-Functional Lubricator 2 Outlet injection feeds for Progressive Distributors Up to 8 direct outlet injectors feeds The compact
More information28.1. NEMA Contactors and Starters. Contents. Contactors Non-Reversing and Reversing. Freedom Series. Product Description
.1 NM ontactors and Starters Non- and ontactors ontactors Non- and Product escription Non- ontactors are most commonly used to switch motor loads in applications where running overcurrent protection is
More informationAccessories. Accessories Catalogue
Accessories Accessories Catalogue 1 Multi Line Accessories INDUSTRIAL Multi Line Accessories Pump Elements For XGS, AX and AC Pumps Blanking Plugs Fast Prime Kit AC Pump 78033 0.010cc Element Red 78034
More informationAir Actuated Ball Valves 3-Way T-Port Stainless Steel, Full Bore 1/4 to 2 NPT
ir ctuated all Valves 3-Way T-Port Stainless Steel, ull ore 1/4 to 2 SRIS eatures ull Port 3-way T flow path irect mount valve with standard ISO5211 mount 316 stainless steel body, ball and stem ctuators
More informationL & S Series Linear Slides
& S Series inear Slides asic Selection S Series (short) single bearing block design, short overall length. (Photo this page) Series (long) double bearing block design, increased bearing support. (Photo
More informationGrease-lubricating pump FF... DSK US (05.05)
Grease-lubricating pump FF... DSK 2-008-00-US (05.05) electrically operated, for small and medium-sized multiple-line and progressive systems PSG-2 with cycle switch VPB with cycle switch PSG-2 with cycle
More informationMonarch D.C. Hydraulic Power Systems. Comprehensive information may be found on the page referenced below each selection category.
Monarch D.C. Hydraulic Power Systems MODEL M-319 Description: Pump/Motor/Reservoir/Valve Check Valve 2-Way/2-Position Normally Closed Solenoid Operated Lowering Valve Externally Adjustable Relief Valve
More informationVCR. Metal Gasket Face Seal Fittings. 1/16 to 1 in. and 6 to 18 mm sizes. High-purity stainless steels
www.swagelok.com Metal asket ace Seal ittings /6 to and 6 to 8 mm sizes igh-purity stainless steels The original design, the authentic brand 2 Metal asket ace Seal ittings ontents lands Page 4 odies Page
More informationSpring Return and Double Acting Pneumatic Quarter-Turn Actuators For Output Torques to 27,624 lb.in.
Keystone Pneumatic Pneumatic ctuator ctuator Spring Return and ouble cting Pneumatic Quarter-Turn ctuators For Output Torques to 27,624 lb.in. Features and enefits Compact rack and pinion design utilizes
More informationProducts RELIABLE HIGH QUALITY PRODUCTS FOR IMPROVED PERFORMANCE
Products RLIL HIGH QULITY PROUTS FOR IMPROV PRFORMN High performance products. Hägglunds is a leading world-wide supplier of complete hydraulic drive systems, primarily for industrial, mobile and marine
More informationFRL/AirCare Air Controls & Accessories
FRL/irare ir ontrols & ccessories Lincoln Regulators, Filters & Lubricators well-planned compressed air system ensures minimum pressure loss in the system, and the removal of contaminants: water, compressor
More informationDEP7 SG Iron Excess Pressure Valve
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
More informationRW Series eatures and Benefits
RW Series...............................................................................3-6 eatures and Benefits..............................................................................3 ow To Order....................................................................................4
More informationCipriani Harrison Valves Corp.
pplication Sanitary ball valves are used in stainless steel piping systems for isolation, either manually or automatically operated. The full port design with zero flow restriction makes it an optimum
More informationModel CHASSIS LUBE ELECTRIC GREASE PUMP Series "C"
Model 94222 CHASSIS LUBE ELECTRIC GREASE PUMP Series "C" Indicates change MAY - 2004 FORM 403466 Section - Q3 Page - 12B 7.75" (197 mm) 12.6" (321 mm) 0.35" (9 mm) Mounting Holes 4.85" (123 mm) 8.85" (225
More informationSeries 1000 Divider Valve Manifold
Series 1000 Divider Valve Manifold Progressive Systems General The Series 1000 progressive divider valve manifold distributes and proportions incoming oil or grease to bearing points. A typical divider
More informationJDN AIR HOISTS PROFI
JN IR HOISTS PROI JN IR HOISTS PROI arrying capacities: 550 Ibs up to 00+ metric tons ir pressure: 60 psi or 87 psi versions available Proven in practice: JN ir Hoists PROI Series are superior the most
More informationJune 2005 CN35 Electrically Held Vol. 2, Ref. No. [0494]
7-2 Lighting ontactors Open ontrol June 2005 N5 lectrically Held Vol. 2, Ref. No. [09] ontents eatures Instructional Leaflets 7 escription Page lectrically Held Product escription....... 7-2 pplication
More informationCompact Cylinder. With a short overall length, the space saving cylinder helps to make various jigs and equipment more compact.
Compact Cylinder Series CQ ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø1, ø With a short overall length, the space saving cylinder helps to make various jigs and equipment more compact. Variations Standard Series
More informationPVL Series Solenoid & Remote Pilot Operated 1/8" & 1/4" Valves zpv06
PVL Series Solenoid & Remote Pilot Operated /8" & /4" Valves zpv06 Section www.parker.com/pneu/pvl asic Valve unctions... 3 Stacking System Overview... 4 eatures (PVL & PVL)... 5 Part Numbers Stacking
More informationADEX Series. Air Control Valves. Section D
X Series ir ontrol alves 00.0 v.8 v.47 v ort 5 ort /8" ort Section www.parker.com/pneu/adex X iking Z asic alve unctions...00 asic alve eatures...0 ommon art umbers / R Type alves...02 odel umber Index
More informationPBA Series. Bent Axis Piston Pumps. cast iron pump body, high output pressure, high performance, high rotational speeds...
P Series ent xis Piston s cast iron pump body, high output pressure, high performance, high rotational speeds... www.hidrocel.com.tr 1 ontents esign of P s Range and characteristics P 17cc P 25cc P 35cc
More informationInstallation, Maintenance & Operating Instructions
-SS VVS nstallation, aintenance & Operating nstructions - SS VVS TO The ulflo -Series feature both direct acting and internal pilot operated models with either screw or flange type connections. The threaded
More informationDD & DM Valves. Dualine, Grease & Oil. General. Operation. Features. DM Valve. DD Valve R5 09/12
DD & DM Valves Dualine, Grease & Oil General DD and DM Valves are completely hydraulic in operation and will deliver either oil or grease. These Dualine valves are also fully and individually adjustable
More informationFeed Pumps FZP / MFZP
eed Pumps ZP / MZP Symbol General The feed pump from the ZP series is a vane pump for the low-pressure range with constant flow rate. Product eatures l irect drive pump no bell housing or coupling required
More informationIsys Micro Series. Valve Products. Operating information. Material specifications. Pilot configuration
atalog 000-3US The Valve System incorporates a space saving back to back valve mounting design, and achieves flow rates of 0.35 v per valve with valves having a combined width of mm. This plug-in valve
More informationRod end male thread. With rubber bumper 056(9/16") 075(3/4") 106(1 1/16") 150(1 1/2") 250(2 1/2") 300(3")
T.ID0-1 New ompact ylinder Series NQ8 ore size: 06(9/16 ),(/ ),106(1 1/16 ),(1 1/ ) 00( ),0( 1/ ),00( ),00( ) Now available in 00 ( ) and 00 ( ) bore sizes Standard type ctuation Style uilt-in magnet Rod
More informationCipriani Harrison Valves Corp.
Shutoff & Divert Valve pplication Shutoff and divert valves are used in process flow systems for stopping or diverting the flow of liquid. variety of body configurations allows flexibility in designing
More informationADEX Series Air Control Valves A00.01 Cv M3 Port A05.18 Cv M5 Port A12.47 Cv 1/8" Port zpv02 A B C D E F G H. Section H
X Series ir ontrol alves 00.0 v ort 05.8 v 5 ort.47 v /8" ort zpv02 Section www.parker.com/pneu/adex asic alve unctions... 2 asic alve eatures... ommon art umbers / R Type alves... 4 odel umber Index /
More informationTriboTec LUBRICATION PUMP VEG
LUBRICATION PUMP APPLICATION The lubricator is used as a source of pressure-lubricant for multi-line central lubrication systems. Due to the choice of the number of outlets in combination with progressive
More information