TEST REPORT. EN Luminaires Part 2: Particular requirements Section 21: Rope Lights

Transcription

1 TEST REORT EN Luminaires art 2: articular requirements Section 21: Rope Lights Report reference No.... : ED S Tested by... : Coral Chen Approved by... : Kobe Mai Date of issue... : August 16, 2017 Contents... : 54 pages Testing laboratory Name... : EMTEK(DONGGUAN) CO., LTD. Address... : No.281, Guantai Road, Nancheng District, Dongguan, Guangdong, China. Testing location... : Same as above Client Applicant name... : GLOBAL(LED) LIGHTING SOLUTIONS Address... : Suite 402, 4th oor, Northbank Buiding Lane, Northbank Lane Century City Town,7441 Manufacturer name... : GLOBAL(LED) LIGHTING SOLUTIONS Address... : Suite 402, 4th oor, Northbank Buiding Lane, Northbank Lane Century City Town,7441 Factory name... : GLOBAL(LED) LIGHTING SOLUTIONS Address... : Suite 402, 4th oor, Northbank Buiding Lane, Northbank Lane Century City Town,7441 Test speci cation Standard... : EN :2015 used in conjunction with EN :2015 Test procedure... : Safety rocedure deviation... : Non-standard test method... : Test item roduct name... : x-glo strip light Trademark... : Model and/or type reference... : x-glo v Rating(s)... : 110V~; 50/60Hz; 13W/m, Max. 4.8A TRF NO.: IEC60598_2_21A age 1 of 54 Report N o.: ED S Ver.1.0

2 Test item particulars... : Classification of installation and use... : -- Supply Connection... : Supply cord... : ossible test case verdicts: - test case does not apply to the test object... : - test object does meet the requirement... : (ass) - test object does not meet the requirement... : F (Fail) Testing Date of receipt of test item... : July 27, 2017 Date (s) of performance of tests... : July 27, 2017 to August 16, 2017 General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Throughout this report a comma / point is used as the decimal separator. Clause numbers between brackets refer to clauses in IEC Summary of testing: 1. There are one model covered in this report. 2. Full tests were performed on model x-glo v. And the tests results complied with the requirements of the standards mentioned in page one. 3. EN :2015, EN :2001 was considered, details see Attachment No.1 4. EN 62301:2008+A1:2013+A2:2015 was considered, details see Attachment No IEC/TR 62778: 2014 was considered in this report, the RG level of this product is exempt group. Details see Attachment No.3 6. EN 62471: 2008 was evaluated, classification group: exempt risk 1 risk 2 risk 3, details see report ED S. TRF NO.: IEC60598_2_21A age 2 of 54 Report No.: ED S Ver.1.0

3 Copy of marking plate: Sticking on the luminaires Note: 1. The height of graphical symbols shall not be less than 5 mm. 2. The height of letters and numerals either shown separately or with or as part of symbols shall not be less than 2 mm. 3. The height of WEEE symbols shall not be less than 7 mm. General product information: 1. LED chains, Class II; I The product connected to supply without plug. 3. Flexible sealed lighting chains. TRF NO.: IEC60598_2_21A age 3 of 54 Report No.: ED S Ver.1.0

4 21.4 (0) GENERAL TEST REQUIREMENTS 21.4 (0.1) Information for luminaire design considered... : Yes No Lamp standard: 21.4 (0.3) More sections applicable... : Yes No Section/s: 21.5 (2) CLASSIFICATION 21.5 (2.2) Type of protection... : Class II 21.5 (2.3) Degree of protection... : I (2.4) Luminaire suitable for direct mounting on normally flammable surfaces... : Yes No 21.5 (2.5) Luminaire for normal use... : Yes No Luminaire for rough service... : Yes No (-) Class II or Class III Class II (-) Rope lights for outdoor use shall be I44 or higher I (3) MARKING 21.6 (3.2) Mandatory markings osition of the marking Format of symbols/text 21.6 (3.3) Additional information Language of instructions English 21.6 (3.3.1) Combination luminaires 21.6 (3.3.2) Nominal frequency in Hz 50/60Hz 21.6 (3.3.3) Operating temperature 21.6 (3.3.4) Symbol or warning notice 21.6 (3.3.5) Wiring diagram 21.6 (3.3.6) Special conditions 21.6 (3.3.7) Metal halide lamp luminaire warning 21.6 (3.3.8) Limitation for semi-luminaires 21.6 (3.3.9) ower factor and supply current 21.6 (3.3.10) 21.6 (3.3.11) Suitability for use indoors Luminaires with remote control TRF NO.: IEC60598_2_21A age 4 of 54 Report No.: ED S Ver.1.0

5 21.6 (3.3.12) 21.6 (3.3.13) 21.6 (3.3.14) 21.6 (3.3.15) 21.6 (3.3.16) 21.6 (3.3.17) 21.6 (3.3.18) 21.6 (3.3.19) 21.6 (3.3.20) 21.6 (3.3.21) 21.6 (3.3.22) Clip-mounted luminaire warning Specifications of protective shields Symbol for nature of supply ~ Rated current of socket outlet Rough service luminaire Mounting instruction for type Y, type Z and some type X attachments Non-ordinary luminaires with VC cable rotective conductor current in instruction if applicable rovided with information if not intended to be mounted within arm s reach Non replaceable and non-user replaceable light sources information provided Cautionary symbol Controllable luminaires, classification of insulation provided type Y Non replaceable light sources 21.6 (3.4) Test with water 15S Test with hexane 15S Legible after test Label attached (-) Rope light marking Rated voltage and wattage marked on the rope light Durable non-removable label if information on the cable (-) Rope light and packing marking Marking if only for indoor use (-) Marking on the packing or instructions Marking a) e) (4) CONSTRUCTION (4.2) Components replaceable without difficulty (4.3) Wireways smooth and free from sharp edges TRF NO.: IEC60598_2_21A age 5 of 54 Report No.: ED S Ver.1.0

6 (4.4) Lampholders (4.4.1) Integral lampholder (4.4.2) Wiring connection (4.4.3) Lampholder for end-to-end mounting (4.4.4) ositioning - pressure test (N)... : After test the lampholder comply with relevant standard sheets and show no damage After test on single-capped lampholder the lampholder have not moved from its position and show no permanent deformation - bending test (N)... : After test the lampholder have not moved from its position and show no permanent deformation (4.4.5) eak pulse voltage (4.4.6) Centre contact (4.4.7) arts in rough service luminaires resistant to tracking (4.4.8) Lamp connectors (4.4.9) Caps and bases correctly used (4.4.10) Light source for lampholder or connection according IEC not connected another way (4.5) Starter holders Starter holder in luminaires other than class II Starter holder class II construction (4.7) Terminals and supply connections (4.7.1) Contact to metal parts (4.7.2) Test 8 mm live conductor Test 8 mm earth conductor (4.7.3) Terminals for supply conductors ( ) Welded method and material - stranded or solid conductor - spot welding - welding between wires - Type Z attachment - mechanical test according to electrical test according to TRF NO.: IEC60598_2_21A age 6 of 54 Report No.: ED S Ver.1.0

7 - heat test according to and (4.7.4) Terminals other than supply connection (4.7.5) Heat-resistant wiring/sleeves (4.7.6) Multi-pole plug - test at 30 N (4.8) Switches - adequate rating - adequate fixing - polarized supply - compliance with IEC for electronic switches (4.9) Insulating lining and sleeves (4.9.1) Retainment Method of fixing... : (4.9.2) Insulated linings and sleeves: Resistant to a temperature > 20 C to the wire temperature or a) & c) Insulation resistance and electric strength b) Ageing test. Temperature ( C)... : (4.10) Double or reinforced insulation (4.10.1) (4.10.2) (4.10.3) No contact, mounting surface accessible metal parts wiring of basic insulation Safe installation fixed luminaires Capacitors and switches Interference suppression capacitors according to IEC Assembly gaps: - not coincidental - no straight access with test probe Retainment of insulation: - fixed - unable to be replaced; luminaire inoperative - sleeves retained in position - lining in lampholder (4.11) Electrical connections and current-carrying parts TRF NO.: IEC60598_2_21A age 7 of 54 Report No.: ED S Ver.1.0

8 (4.11.1) (4.11.2) (4.11.3) (4.11.4) (4.11.5) (4.11.6) Contact pressure Screws: - self-tapping screws - thread-cutting screws Screw locking: - spring washer - rivets Material of current-carrying parts No contact to wood or mounting surface Electro-mechanical contact systems (4.12) Screws and connections (mechanical) and glands (4.12.1) (4.12.2) (4.12.4) (4.12.5) Screws not made of soft metal Screws of insulating material Torque test: torque (Nm); part... : Torque test: torque (Nm); part... : Torque test: torque (Nm); part... : Screws with diameter < 3 mm screwed into metal Locked connections: Screw for fixing fuse box: 2.92mm, 0.5Nm - fixed arms; torque (Nm)... : - lampholder; torque (Nm)... : - push-button switches; torque 0,8 Nm... : Screwed glands; force (Nm)... : 2.5Nm (4.13) Mechanical strength (4.13.1) Impact tests: - fragile parts; energy (Nm)... : - other parts; energy (Nm)... : 0.5 Nm 1) live parts TRF NO.: IEC60598_2_21A age 8 of 54 Report No.: ED S Ver.1.0

9 (4.13.3) (4.13.4) (4.13.6) 2) linings 3) protection 4) covers Straight test finger 30N Rough service luminaires - I54 or higher a) fixed b) hand-held c) delivered with a stand d) for temporary installations and suitable for mounting on a stand Tumbling barrel (4.14) Suspensions, fixings and means of adjusting (4.14.1) (4.14.2) (4.14.3) Mechanical load: A) four times the weight B) torque 2,5 Nm C) bracket arm; bending moment (Nm)... : D) load track-mounted luminaires E) clip-mounted luminaires, glass-shelve. Thickness (mm)... : Metal rod. diameter (mm)... : Fixed luminaire or independent control gear without fixing devices Load to flexible cables Mass (kg)... : Stress in conductors (N/mm²)... : Mass (kg) of semi-luminaire... : Bending moment (Nm) of semi-luminaire... : Adjusting devices: - flexing test; number of cycles... : - strands broken... : - electric strength test afterwards TRF NO.: IEC60598_2_21A age 9 of 54 Report No.: ED S Ver.1.0

10 (4.14.4) (4.14.5) (4.14.6) Telescopic tubes: cords not fixed to tube; no strain on conductors Guide pulleys Strain on socket-outlets (4.15) Flammable materials (4.15.2) - glow-wire test 650 C... : See Test Table (13.3.2) - spacing 30 mm - screen withstanding test of screen dimensions - no fiercely burning material - thermal protection - electronic circuits exempted Luminaires made of thermoplastic material with lamp control gear a) construction b) temperature sensing control c) surface temperature (4.16) Luminaires for mounting on normally flammable surfaces (4.16.1) (4.16.2) (4.16.3) No lamp control gear... : (compliance with Section 12) Lamp control gear spacing: - spacing 35 mm - spacing 10 mm Thermal protection: - in lamp control gear - external - fixed position - temperature marked lamp control gear Design to satisfy the test of 12.6 (see clause 12.6) (4.17) Drain holes Clearance at least 5 mm (4.18) Resistance to corrosion TRF NO.: IEC60598_2_21A age 10 of 54 Report No.: ED S Ver.1.0

11 (4.18.1) (4.18.2) (4.18.3) - rust-resistance - season cracking in copper - corrosion of aluminium (4.19) Ignitors compatible with ballast (4.20) Rough service vibration (4.21) rotective shield (4.21.1) (4.21.2) (4.21.3) (4.21.4) Shield fitted if tungsten halogen lamps or metal halide lamps Shield of glass if tungsten halogen lamps articles from a shattering lamp not impair safety No direct path Impact test on shield Glow-wire test on lamp compartment... : See Test Table (13.3.2) (4.22) Attachments to lamps not cause overheating or damage (4.23) Semi-luminaires comply Class II (4.24) hotobiological hazards (4.24.1) (4.24.2) No excessive UV radiation if tungsten halogen lamps and metal halide lamps (Annex ) Retinal blue light hazard Luminaires with Ethr : a) Fixed luminaires RG0 - distance x m, borderline between RG1 and RG2.. : - marking and instruction according b) ortable and handheld luminaires - marking according if RG1 exceeded at 200 mm according to IEC/TR ortable luminaires for children IEC and Mains socket outlet nightlights IEC not exceed RG1 at 200 mm according to IEC/62778 (4.25) Mechanical hazard No sharp point or edges TRF NO.: IEC60598_2_21A age 11 of 54 Report No.: ED S Ver.1.0

12 (4.26) Short-circuit protection (4.26.1) (4.26.2) Adequate means of uninsulated accessible SELV parts Short-circuit test with test chain according Test chain not melt through Test sample not exceed values of Table 12.1 and 12.2 (4.27) Terminal blocks with integrated screwless earthing contacts Test according Annex V ull test of terminal fixing (20 N) After test, resistance < 0,05 ull test of mechanical connection (50 N) After test, resistance < 0,05 Voltage drop test, resistance < 0,05 (4.28) Fixing of thermal sensing control Not plug-in or easily replaceable type Reliably kept in position No adhesive fixing if UV radiations from a lamp can degrade the fixing Not outside the luminaire enclosure Test of adhesive fixing: Max. temperature on adhesive material ( C)... : 100 cycles between t min and t max Temperature sensing control still in position (4.29) Luminaires with non-replaceable light source Not possible to replace light source Live part not accessible after parts have been opened by hand or tools (4.30) Luminaires with non-user replaceable light source If protective cover provide protection against electric shock and marked with caution, electric shock risk symbol: Minimum two fixing means (4.31) Insulation between circuits Circuits insulated from LV supply fulfil requirements according TRF NO.: IEC60598_2_21A age 12 of 54 Report No.: ED S Ver.1.0

13 (4.31.1) (4.31.2) (4.31.3) Controllable luminaires requiring same level of insulation for all components, the insulation between control terminals and LV supply fulfil requirements according SELV circuits Used SELV source Voltage ELV Insulating of SELV circuits from LV supply Insulating of SELV circuits from other non SELV circuits Insulating of SELV circuits from FELV Insulating of SELV circuits from other SELV circuits SELV circuits insulated from accessible parts according Table X.1 lugs not able to enter socket-outlets of other voltage systems Socket outlets does not admit plugs of other voltage systems lugs and socket-outlets does not have protective conductor contact FELV circuits Used FELV source Voltage ELV Insulating of FELV circuits from LV supply FELV circuits insulated from accessible parts according Table X.1 lugs not able to enter socket-outlets of other voltage systems Socket outlets does not admit plugs of other voltage systems Socket-outlets does not have protective conductor contact Other circuits Other circuits insulated from accessible parts according Table X.1 Class II construction with equipotential bonding for protection against indirect contacts with live parts: - conductive parts are connected together TRF NO.: IEC60598_2_21A age 13 of 54 Report No.: ED S Ver.1.0

14 - test according conductive part not cause an electric shock in case of an insulation fault - equipotential bonding in master/slave applications - master luminaire provided with terminal for accessible conductive parts of slave luminaires - slave luminaire constructed as class I (4.32) Overvoltage protective devices Comply with IEC External to controlgear and connected to earth: - only in fixed luminaires - only connected to protective earth.2 (-) Terminal blocks Clause 4.6 of IEC referring to terminal blocks does not apply.3 (-) Terminals and supply connections Comply with Annex A.4 (-) Control units Forming an integral part enclosed in non-flammable insulating material tested according Securely fixed to the cable Electronic control device comply with IEC LED driver comply with IEC (-) Mechanical strength a) Rigid rope lights 1) ull test: force 60 N 2) Torque test: torque 0,15 Nm b) Flexible rope lights 1) ull test: force 60 N 2) Torque test: torque 0,15 Nm 3) Cylinder times at 25 C ± 2 C For rope lights having an I number over X0 Additionally: Cylinder times at -15 C ± 2 C 4) Mandrel of between 4 and 5 times the diameter of test piece c) Impact test at low temperature of -15 C ± 5 C TRF NO.: IEC60598_2_21A age 14 of 54 Report No.: ED S Ver.1.0

15 21.8 (11) CREEAGE DISTANCES AND CLEARANCES 21.8 (11.2) Creepage distances and clearances... : See Table 21.8 (11.2) Working voltage (V)... : 110V Rated pulse voltage (kv)... : -- Voltage form... : Sinusoidal Non-sinusoidal TI... : < 600 > 600 Impulse withstand category (Normal category II) (Category III Annex U) Category II Category III (14) SCREW TERMINALS Separately approved; component list (see Annex 1) art of the luminaire (see Annex 3) (15) SCREWLESS TERMINALS AND ELECTRICAL CONNECTIONS Separately approved; component list... : (see Annex 1) art of the luminaire... : (see Annex 4) (5) EXTERNAL AND INTERNAL WIRING (5.2) Supply connection and external wiring (5.2.1) Means of connection... : Supply cord Outdoor luminaire has not VC insulated external wiring if not class III or SELV 25 V a.c./60 V d.c. or protected from outdoor environment (5.2.2) Type of cable... : See ANEEX 1 Nominal cross-sectional area (mm²)... : See ANEEX 1 Cables equal to IEC or IEC (5.2.3) Type of attachment, X, Y or Z Type Y (5.2.5) (5.2.6) Type Z not connected to screws Cable entries: - suitable for introduction TRF NO.: IEC60598_2_21A age 15 of 54 Report No.: ED S Ver.1.0

16 (5.2.7) (5.2.8) (5.2.9) (5.2.10) ( ) ( ) ( ) - adequate degree of protection Cable entries through rigid material have rounded edges Insulating bushings: - suitably fixed - material in bushings - material not likely to deteriorate - tubes or guards made of insulating material Locking of screwed bushings Cord anchorage: - covering protected from abrasion - clear how to be effective - no mechanical or thermal stress - no tying of cables into knots etc. - insulating material or lining Cord anchorage for type X attachment: a) at least one part fixed b) types of cable c) no damaging of the cable d) whole cable can be mounted e) no touching of clamping screws f) metal screw not directly on cable g) replacement without special tool Glands not used as anchorage Labyrinth type anchorages Adequate cord anchorage for type Y and type Z attachment Tests: - impossible to push cable; unsafe - pull test: 25 times; pull (N)... : 60N - torque test: torque (Nm)... : 0.25Nm - displacement 2 mm 0.7mm<2.0mm TRF NO.: IEC60598_2_21A age 16 of 54 Report No.: ED S Ver.1.0

17 (5.2.11) (5.2.12) (5.2.13) (5.2.14) (5.2.16) (5.2.17) (5.2.18) - no movement of conductors - no damage of cable or cord - function independent of electrical connection External wiring passing into luminaire Looping-in terminals Wire ends not tinned Wire ends tinned: no cold flow Mains plug same protection Class III luminaire plug No unsafe compatibility Appliance inlets (IEC 60320) Installation couplers (IEC 61535) Other appliance inlet or connector according relevant IEC standard No standardized interconnecting cables properly assembled Used plug in accordance with - IEC other standard (5.3) Internal wiring (5.3.1) ( ) Internal wiring of suitable size and type Through wiring - not delivered/ mounting instruction - factory assembled - socket outlet loaded (A)... : - temperatures... : (see Annex 2) Green-yellow for earth only Internal wiring connected directly to fixed wiring Cross-sectional area (mm²)... : Insulation thickness TRF NO.: IEC60598_2_21A age 17 of 54 Report No.: ED S Ver.1.0

18 ( ) ( ) ( ) ( ) ( ) (5.3.2) (5.3.3) (5.3.4) (5.3.5) (5.3.6) (5.3.7) Extra insulation added where necessary Internal wiring connected to fixed wiring via internal current-limiting device Adequate cross-sectional area and insulation thickness Double or reinforced insulation for class II Conductors without insulation SELV current-carrying parts Insulation thickness other than VC or rubber Sharp edges etc. No moving parts of switches etc. Joints, raising/lowering devices Telescopic tubes etc. No twisting over 360 Insulating bushings: - suitable fixed - material in bushings - material not likely to deteriorate - cables with protective sheath Joints and junctions effectively insulated Strain on internal wiring Wire carriers Wire ends not tinned Wire ends tinned: no cold flow.2 (-) Cables for rope lights Type of cable... : Cables not lighter than IEC or IEC for class II rope lights TRF NO.: IEC60598_2_21A age 18 of 54 Report No.: ED S Ver.1.0

19 Cables not lighter than insulation according to of part 1 for class III rope lights Nominal cross-sectional area (mm²)... : (see Annex 1) Mechanical properties according and of part 1.3 (-) Cord anchorage test ull test 30 N 25 times on single-core cable.4 (-) lugs and cable length Splash-proof plug or permanent connection if for outdoor use Length of the cable between the plug and the connection to the rope light not less than 1,5 m.5 (-) Maximum length of extendable class II rope lights Maximum length 100 m for 0,5 mm²cable Maximum length 150 m for 0,75 mm²cable (8) ROTECTION AGAINST ELECTRIC SHOCK (8.2.1) (8.2.2) Live parts not accessible Basic insulated parts not used on the outer surface without appropriate protection Basic insulated parts not accessible with standard test finger on portable, settable and adjustable luminaires Basic insulated parts not accessible with Ø 50 mm probe from outside, other types of luminaires Lamp and starterholders in portable and adjustable luminaires comply with double or reinforced insulation requirements Basic insulation only accessible under lamp or starter replacement rotection in any position Double-ended tungsten filament lamp Insulation lacquer not reliable Double-ended high pressure discharge lamp Relevant warning according to fitted to the luminaire ortable luminaire adjusted in most unfavourable position TRF NO.: IEC60598_2_21A age 19 of 54 Report No.: ED S Ver.1.0

20 21.12 (8.2.3.a) (8.2.3.b) (8.2.3.c) (8.2.4) (8.2.5) (8.2.6) (8.2.7) Class II luminaire: - basic insulated metal parts not accessible during starter or lamp replacement - basic insulation not accessible other than during starter or lamp replacement - glass protective shields not used as supplementary insulation BC lampholder of metal in class I luminaires shall be earthed SELV circuits with exposed current carrying parts: Ordinary luminaire: - touch current... : - no-load voltage... : Other than ordinary luminaire: - nominal voltage... : ortable luminaire have protection independent of supporting surface Compliance with the standard test finger or relevant probe Covers reliably secured Discharging of capacitors 0,5 F ortable plug connected luminaire with capacitor Other plug connected luminaire with capacitor Discharge device on or within capacitor Discharge device mounted separately (12) ENDURANCE TEST AND THERMAL TEST (-) If I > I 20 relevant test of (12.4), (12.5) and (12.6) after (9.2) before (9.3) specified in (12.3) Endurance test: - mounting-position... : Acc. to user manual - test temperature ( C)... : 35 C - total duration (h)... : 240h - supply voltage: Un factor; calculated voltage (V)... : 264V TRF NO.: IEC60598_2_21A age 20 of 54 Report No.: ED S Ver.1.0

21 - lamp used... : Integral LED (12.3.2) (12.4) (12.5) (12.6) (12.6.1) (12.6.2) (12.7) (12.7.1) ( ) After endurance test: - no part unserviceable - luminaire not unsafe - no damage to track system - marking legible - no cracks, deformation etc. Thermal test (normal operation) (see Annex 2) Thermal test (abnormal operation) (see Annex 2) Thermal test (failed lamp control gear condition): Through wiring or looping-in wiring loaded by a current of (A)... : - case of abnormal conditions... : - electronic lamp control gear - measured winding temperature ( C): at 1,1 Un... : - measured mounting surface temperature ( C) at 1,1 Un... : - calculated mounting surface temperature ( C)... : - track-mounted luminaires Temperature sensing control - case of abnormal conditions... : - thermal link - manual reset cut-out - auto reset cut-out - measured mounting surface temperature ( C)... : - track-mounted luminaires Thermal test (failed lamp control gear in plastic luminaires): Luminaire without temperature sensing control Luminaire with fluorescent lamp 70W Test method or Annex W... : TRF NO.: IEC60598_2_21A age 21 of 54 Report No.: ED S Ver.1.0

22 Test according to : - case of abnormal conditions... : - Ballast failure at supply voltage (V)... : - Components retained in place after the test - Test with standard test finger after the test Test according to Annex W: - case of abnormal conditions... : ( ) ( ) (12.7.2) - measured winding temperature ( C): at 1,1 Un... : - measured temperature of fixing point/exposed part ( C): at 1,1 Un... : - calculated temperature of fixing point/exposed part ( C)... : Ball-pressure test... : See Table (13.2.1) Luminaire with discharge lamp, fluorescent lamp > 70W, transformer > 10 VA - case of abnormal conditions... : - measured winding temperature ( C): at 1,1 Un... : - measured temperature of fixing point/exposed part ( C): at 1,1 Un... : - calculated temperature of fixing point/exposed part ( C)... : Ball-pressure test... : See Table (13.2.1) Luminaire with short circuit proof transformers 10 VA - case of abnormal conditions... : - Components retained in place after the test - Test with standard test finger after the test Luminaire with temperature sensing control - thermal link... : Yes No - manual reset cut-out... : Yes No - auto reset cut-out... : Yes No - case of abnormal conditions... : - highest measured temperature of fixing point/ exposed part ( C):... : Ball-pressure test:... : See Table (13.2.1) (-) Test voltage TRF NO.: IEC60598_2_21A age 22 of 54 Report No.: ED S Ver.1.0

23 rovision of d) of part 1 and if class III rope lights 1,1 x rated voltage of transformer/convertor rovision of d) of part 1 and if class III rope lights 1,06 x rated voltage of transformer/convertor (-) Short-circuit test of rectifier No emission of flames or molten material or production of flammable gases and no live parts accessible when short-circuit output of the rectifier (9) RESISTANCE TO DUST, SOLID OBJECTS AND MOISTURE (-) If I > I 20 the order of tests as specified in clause (9.2) Tests for ingress of dust, solid objects and moisture: - classification according to I... : I65 - mounting position during test... : Acc. to user manual - fixing screws tightened; torque (Nm)... : -- - tests according to clauses... : & electric strength test afterwards a) no deposit in dust-proof luminaire b) no talcum in dust-tight luminaire c) no trace of water on current-carrying parts or on insulation where it could become a hazard d) i) For luminaires without drain holes no water entry d) ii) For luminaires with drain holes no hazardous water entry e) no water in watertight luminaire f) no contact with live parts (I 2X) f) no entry into enclosure (I 3X and I 4X) f) no contact with live parts (I3X and I4X) g) no trace of water on part of lamp requiring protection from splashing water h) no damage of protective shield or glass envelope (9.3) Humidity test 48 h 25 C, 93 % RH (10) INSULATION RESISTANCE AND ELECTRIC STRENGTH (10.2.1) Insulation resistance test TRF NO.: IEC60598_2_21A age 23 of 54 Report No.: ED S Ver.1.0

24 Cable or cord covered by metal foil or replaced by a metal rod of mm Ø... : (10.2.2) Insulation resistance (M )... : SELV - between current-carrying parts of different polarity : - between current-carrying parts and mounting surface... : - between current-carrying parts and metal parts of the luminaire... : - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts... : - Insulation bushings as described in Section 5... : Other than SELV - between live parts of different polarity... : >100M - between live parts and mounting surface... : >100M - between live parts and metal parts... : - between live parts of different polarity through action of a switch... : - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts... : - Insulation bushings as described in Section 5... : Electric strength test Dummy lamp Luminaires with ignitors after 24 h test Luminaires with manual ignitors Test voltage (V)... : SELV - between current-carrying parts of different polarity : - between current-carrying parts and mounting surface... : - between current-carrying parts and metal parts of the luminaire... : - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts... : - Insulation bushings as described in Section 5... : TRF NO.: IEC60598_2_21A age 24 of 54 Report No.: ED S Ver.1.0

25 21.15 (10.3) Other than SELV - between live parts of different polarity... : 1220V - between live parts and mounting surface... : 2440V - between live parts and metal parts... : - between live parts of different polarity through action of a switch... : - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts... : - Insulation bushings as described in Section 5... : Touch current or protective conductor current (ma) : 0.1mA (13) RESISTANCE TO HEAT, FIRE AND TRACKING (13.2.1) (13.3.1) (13.3.2) (13.4) Ball-pressure test... : See Test Table (13.2.1) Needle-flame test (10 s)... : See Test Table (13.3.1) Glow-wire test (650 C)... : See Test Table (13.3.2) roof tracking test (IEC 60112)... : See Test Table (13.4) (-) Flexible pipes of rope lights in compliance with IEC TRF NO.: IEC60598_2_21A age 25 of 54 Report No.: ED S Ver.1.0

26 21.8 (11.2) TABLES: Creepage distances and clearances Table 11.1 Minimum distances (mm) for a.c. (50/60 Hz) sinusoidal voltages RMS working voltage (V) not exceeding Creepage distances Required basic insulation, TI 600 0,6 0,8 1, ,5 Measured Required basic insulation, TI < 600 1,2 1,6 2, Measured Required supplementary insulation TI 600-0,8 1, ,5 Measured Required supplementary insulation TI < 600-1,6 2, Measured Required reinforced insulation - 3, Measured Clearances Required basic insulation 0,2 0,8 1, ,5 Measured Required supplementary insulation - 0,8 1, ,5 Measured Required reinforced insulation - 1, Measured Table 11.2 Minimum distances (mm) for non-sinusoidal pulse voltages TRF NO.: IEC60598_2_21A age 26 of 54 Report No.: ED S Ver.1.0

27 Rated pulse voltage (peak kv) 2,0 2,5 3,0 4,0 5,0 6,0 8,0 Required clearances 1,0 1, ,5 8 Measured Rated pulse voltage (peak kv) Required clearances Measured Rated pulse voltage (peak kv) Required clearances Measured 1. Between pins of fuse link; cr.=cl.=5.0mm(limit cr.=1.6mm, cl.=0.8mm) 2. Between L and N of fuse box: cr.=cl.=5.0mm(limit cr.=1.6mm, cl.=0.8mm) 3. Current-carrying parts and accessible parts: Cr.=cl.=6.0mm(Limit cr.=3.2mm, cl.=1.6mm) 4. Current-carrying parts and supporting surface: Cr.=cl.=6.0mm(Limit cr.=3.2mm, cl.=1.6mm) (13.2.1) TABLE: Ball ressure Test of Thermoplastics Allowed impression diameter (mm)... : 2mm Object/ art No./ Material Manufacturer/ trademark Test temperature ( C) Impression diameter (mm) Fuse box C 1.2mm CB of Fuse C 1.0mm Supplementary information: (13.3.1) TABLE: Needle-flame test (IEC ) Object/ art No./ Material Manufacturer/ trademark Duration of application of test flame (ta); (s) Ignition of specified layer Yes/No Duration of burning (tb) (s) Verdict Connector -- 10s No -- CB of Fuse -- 10s No -- CB of LED -- 10s No -- Supplementary information: (13.3.2) TABLE: Glow-wire test (IEC ) TRF NO.: IEC60598_2_21A age 27 of 54 Report No.: ED S Ver.1.0

28 Glow wire temperature... : 650 C Object/ art No./ Material Manufacturer/ trademark Ignition of specified layer Yes/No Duration of burning (tb) (s) Fuse box -- No 0 Diffuser enclosure -- No 0 Any flame or glowing of the sample extinguished within 30 s of withdrawing the glow-wire, and any burning or molten drop did not ignite the underlying parts (Yes/No)... : Supplementary information: Verdict Yes (13.4) TABLE: roof tracking test (IEC 60112) Test voltage TI... : 175 V Object/ art No./ Material Manufacturer/ trademark Withstand 50 drops without failure on three places or on three specimens Diffuser enclosure -- Yes Yes Yes Supplementary information: Verdict TRF NO.: IEC60598_2_21A age 28 of 54 Report No.: ED S Ver.1.0

29 ANNEX A Requirements for interconnecting connectors for use in rope lights This Annex A consist relevant requirements and modifications of IEC Classification according to protection against electric shock Only enclosed connectors 5.3 Classification according to the style of connector Only free connectors 5.4 Classification according to additional characteristics of connectors According b), d), e), f), h), and j) Identification According a) and b) Non accessibility of live parts Test with test finger on class II rope lights olarisation Improper connection of mating parts is prevented No unsafe compatibility between connectors for class II and class III rope lights of the same manufacturer Male part of class III rope lights not make contact in the female contact of low voltage connectors (e.g. IEC 60320) Manufacturer designed connectors, no unsafe compatibility with systems according IEC and IEC and national domestic plug and socketoutlet systems in the country where the rope light is placed on the market Connection of conductors Cross sectional area of the contact making part of the interconnecting coupler not less than the corresponding conductor in the interconnected cable 6.10 Design of a CBC Adequate breaking capacity Female part at the end of the rope light, other than ordinary, provided with sealing device securely fixed to the coupler 6.13 Dielectric strength Test according clause of this standard Electrical endurance (CBC) Meet the specified breaking capacity Number of cycles 50 TRF NO.: IEC60598_2_21A age 29 of 54 Report No.: ED S Ver.1.0

30 Test according Bendings (non-rewirable connectors) Meet the specified number of bendings Number of cycles 1000 Test according Cable clamp Test according clause.3 of this standard TRF NO.: IEC60598_2_21A age 30 of 54 Report No.: ED S Ver.1.0

31 ANNEX 1: components object/part No. External wire Fuse box Rubber ring CB of Fuse CB of LED Varistor Fuse Connector LED Diffuser enclosure code manufacturer/ trademark B C C B B B B B C C Yuyao Jingyi Electronics Co., Ltd. Dongguan Long Ran lastic Electronic Co., Ltd. Dongguan Long Ran lastic Electronic Co., Ltd. SHENZHEN HENGLONGXIN ELECTRONICS TECHNOLOGY CO LTD HUIZHOU CHUANLIAN ELECTRONIC TECHNOLOGY CO LTD CERGLASS MFG INC SUNNY EAST ENTERRISE CO LTD SHENZHEN CHOGORI TECHNOLOGY CO LTD ShenZhen JuFei Optoelectronics Co., Ltd. KINGFA SCI & TECH CO LTD type/model technical data standard mark(s) of conformity H05RN-F 2x1.0mm2 -- VDE Q7103 I65, 130 C -- O- ring(q7103) Rubber, 130 C -- Tested with appliance Tested with appliance HLX-D 130 C, V-0 -- UL E CL-Y 105 C, V-0 -- UL E D471K V, 0.4W -- VDE CFD 250V, 6.3A -- VDE (female), (male) 250V/10A, 40~105 C I mA, V -- VC-1018 V-0, any color UL E TUV B Tested with appliance Tested with appliance The codes above have the following meaning: A - The component is replaceable with another one, also certified, with equivalent characteristics B - The component is replaceable if authorised by the test house C - Integrated component tested together with the appliance D- Alternative component TRF NO.: IEC60598_2_21A age 31 of 54 Report No.: ED S Ver.1.0

32 ANNEX 2 TABLE: Temperature measurements, thermal tests of Section 12 art Type reference... : x-glo v Lamp used... : Integral LED Lamp control gear used... : See annex 1 Mounting position of luminaire... : As normal used according instruction manual Supply wattage (W)... : 554.5W Supply current (A)... : 5.05A Calculated power factor... : Table: measured temperatures corrected for ta = 25 C: - abnormal operating mode... : During the sample tested under fault condition, the LED driver shut down or fuse open - test 1: rated voltage... : -- - test 2: 1,06 times rated voltage or 1,05 times rated wattage... : - test 3: Load on wiring to socket-outlet, 1,06 times voltage or 1,05 times wattage... : - test 4: 1,1 times rated voltage or 1,05 times rated wattage... : Through wiring or looping-in wiring loaded by a current of A during the test... : Temperature measurements, ( C) Clause 12.4 normal TRF NO.: IEC60598_2_21A age 32 of 54 Report No.: ED S Ver.1.0 1,06 times rated voltage Clause 12.5 abnormal test 1 test 2 test 3 limit test 4 limit Fuse box plastic enclosure outside Ref Fuse box plastic enclosure inside Ref ZV CB of Fuse Ref Connector Ref Input wire Input Connector outside Ref Input Connector inside Ref CB of LED, nearest to center LED Diffuser outside Ref

33 Diffuser inside Ref Mounting surface Ambient Supplementary information: TRF NO.: IEC60598_2_21A age 33 of 54 Report No.: ED S Ver.1.0

34 ANNEX 4 Screwless terminals (part of the luminaire) (15) SCREWLESS TERMINALS (15.2) Type of terminal... : Rated current (A)... : (15.3.1) Material (15.3.2) Clamping (15.3.3) Stop (15.3.4) Unprepared conductors (15.3.5) ressure on insulating material (15.3.6) Clear connection method (15.3.7) Clamping independently (15.3.8) Fixed in position ( ) Conductor size Type of conductor (15.5) Terminals and connections for internal wiring (15.5.1) Mechanical tests ( ) ull test spring-type terminals (4 N, 4 samples)... : ( ) ull test pin or tab terminals (4 N, 4 samples)... : Insertion force not exceeding 50 N ( ) ermanent connections: pull-off test (20 N) (15.5.2) Electrical tests Voltage drop (mv) after 1 h (4 samples)... : Voltage drop of two inseparable joints Number of cycles: Voltage drop (mv) after 10th alt. 25th cycle (4 samples)... : Voltage drop (mv) after 50th alt. 100th cycle (4 samples)... : After ageing, voltage drop (mv) after 10th alt. 25th cycle (4 samples)... : After ageing, voltage drop (mv) after 50th alt. 100th cycle (4 samples)... : (15.6) Terminals and connections for external wiring (15.6.1) Conductors Terminal size and rating TRF NO.: IEC60598_2_21A age 34 of 54 Report No.: ED S Ver.1.0

35 Mechanical tests ( ) ull test spring-type terminals or welded connections (4 samples); pull (N)... : ( ) ull test pin or tab terminals (4 samples); pull (N)... : (15.6.3) Electrical tests Tests according in IEC ( ) ( ) TABLE: Contact resistance test / Heating tests Voltage drop (mv) after 1 h terminal voltage drop (mv) Voltage drop of two inseparable joints Voltage drop after 10th alt. 25th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Continued ageing: voltage drop after 10th alt. 25th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Continued ageing: voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Supplementary information: TRF NO.: IEC60598_2_21A age 35 of 54 Report No.: ED S Ver.1.0

36 Attachment No.1 EN (4) GENERAL REQUIREMENTS - (4) Insulation materials according requirements in Annex N of IEC (4) Compliance of independent controlgear enclosure with IEC (4) Built-in electronic controlgear with double or reinforced insulation comply with Annex O of IEC (4) SELV controlgear comply with Annex L of IEC (see Annex N) (see Annex O) (see Annex L) 6 (6) CLASSIFICATION Built-in controlgear... : Yes No Independent controlgear... : Yes No Integral controlgear... : Yes No 7 (7) MARKING 7.1 (7.1) Mandatory markings (other than integral miscellaneous electronic circuits) a) mark of origin b) model number or type reference d) correlation between interchangeable parts and controlgear marked e) rated supply voltage (V) supply frequency (Hz) supply current (A) f) earthing symbol k) wiring diagram l) value of tc alternative ta 7.1 (-) - control terminals identified, if applicable - (7.2) Marking durable and legible Rubbing 15 s water, 15 s petroleum; marking legible 7.2 (7.1) Information to be provided, if applicable: h) declaration on protection against accidental contact i) cross-section of conductors (mm²) j) number, type and wattage of lamp(s) - (7.2) Marking durable and legible TRF NO.: IEC60598_2_21A age 36 of 54 Report No.: ED S Ver.1.0

37 Attachment No.1 EN Rubbing 15 s water, 15 s petroleum; marking legible 8 (10) ROTECTION AGAINST ACCIDENTAL CONTACT WITH LIVE ARTS - (10.1) Controlgear protected against accidental contact with live parts Rely upon final luminaries - (A2) Voltage measured with 50 k (see Annex A) - (A3) Voltage > 35 V r.m.s. or > 60 V d.c. or protective impendance device - (10.1) Lacquer or enamel not used for protection or insulation Adequate mechanical strength on parts providing protection - (10.2) Capacitors > 0,5 F: voltage after 1 min (V): < 50 V... : (see Annex A) - (10.3) Controlgear providing SELV Accessible conductive parts are insulated from live parts by double or reinforced insulation in SELV controlgear No connection between output circuit and the body or protective earthing curcuit No possibility of connection between output circuit and the body or protective earthing circuit through other conductive parts SELV outputs separated by at least basic insulation ELV conductive parts insulated as live parts Tests according Annex L of IEC (10.4) Accessible conductive parts in SELV circuits Output voltage under load 25 V r.m.s. or 60 V d.c. If output voltage > 25 V r.m.s. or > 60 V d.c.; No load output 35 V peak or 60 V d.c and touch current does not exceed 0,7 ma (peak) or 2 ma d.c.... : One conductive part is insulated if output voltage or current exceeding the values above and withstand test voltage 500 V Double or reinforced insulation bridged by appropriate and at least two resistors or two Y2 capacitors or one Y1 capacitor Y1 or Y2 capacitors comply with IEC TRF NO.: IEC60598_2_21A age 37 of 54 Report No.: ED S Ver.1.0

38 Attachment No.1 EN Resistors comply with test (a) in 14.1 of IEC (8) TERMINALS - (8) Screw terminals according section 14 of IEC : Separately approved; component list (see Annex 1) art of the controlgear (see Annex 2) Screwless terminals according section 15 of IEC : Separately approved; component list (see Annex 1) art of the controlgear (see Annex 3) 10 (9) ROVISION FOR ROTECTIVE EARTHING - (9.1) rovisions for protective earthing Terminal complying with clause 9 Locked against loosening and not possible to loosen by hand Not possible to loosen clamping means unintentionally on screwless terminals Earthing via means of fixing Earthing terminal only used for the earthing of the control gear All parts of material minimizing the danger of electrolytic corrosion Made of brass or equivalent material Contact surface bare metal - (9.2) rovision for functional earthing Comply with clause 8 and (9.3) Earth contact via the track on the printed board Test with a current of 25 A between earthing terminal and each of the accessible metal parts; measured resistance ( ) at 10 A according of IEC : < 0,5... : - (9.4) Earthing of built-in lamp controlgear Earth by means of fixing to earthed metal of luminaire in compliance of 7.2 of IEC Earthing terminal only for earthing the built-in controlgear - (9.5) Earthing via independent controlgear TRF NO.: IEC60598_2_21A age 38 of 54 Report No.: ED S Ver.1.0

39 Attachment No.1 EN (9.5.1) Earth connection to other equipment Looping or through connection, conductor min. 1,5 mm²and of copper or equivalent rotective earthing wires in line with and clause 7 - (9.5.2) Earthing of the lamp compartments powered via the independent lamp controlgear Test with a current of 25 A between input and output earth terminals; measured resistance ( ) between earthing terminal and each of the accessible metal parts at 10 A according of IEC : < 0,5... : Output earthing terminal marked as in 7.1 t) of IEC (11) MOISTURE RESISTANCE AND INSULATION After storage 48 h at 91-95% relative humidity and C measuring of insulation resistance with d.c. 500 V (M ): For basic insulation 2 M... : For double or reinforced insulation 4 M... : Between primary and secondary circuits in controlgear providing SELV, values in Annex L in IEC Between different pole of input terminal: 100 M 12 (12) ELECTRIC STRENGTH - (12) Immediately after clause 11 electric strength test for 1 min Basic insulation for SELV, test voltage 500 V Working voltage 50 V, test voltage 500 V Working voltage > 50 V 1000 V, test voltage (V): Basic insulation, 2U V 1220V Supplementary insulation, 2U V Double or reinforced insulation, 4U V No flashover or breakdown Solid or thin sheet insulation for double or reinforced insulation fulfil the requirements in Annex N in IEC (14) FAULT CONDITIONS - (14) When operated under fault conditions the controlgear: TRF NO.: IEC60598_2_21A age 39 of 54 Report No.: ED S Ver.1.0

40 Attachment No.1 EN does not emit flames or molten material - does not produce flammable gases - protection against accidental contact not impaired Thermally protected controlgear does not exceed the marked temperature value Fault conditions: capacitors, resistors or inductors without proof of compliance with relevant specifications have been short-circuited or disconnected - (14.1) Short-circuit of creepage distances and clearances if less than specified in clause 16 in art 1 (except between live parts and accessible metal parts) Creepage distances on printed boards less than specified in clause 16 in art 1 provided with coating according to IEC (see appended table) (see appended table) - (14.2) Short-circuit or interruption of semiconductor devices (see appended table) - (14.3) Short-circuit across insulation consisting of lacquer, enamel or textile (see appended table) - (14.4) Short-circuit across electrolytic capacitors (see appended table) - (14.5) After the tests has been carried out on three samples: The insulation resistance 1 M... : No flammable gases No accessible parts have become live During the tests, a five-layer tissue paper, where the test specimen is wrapped, does not ignite - (14.6) Relevant fault condition tests with high-power supply 15 (15) CONSTRUCTION - (15.1) Wood, cotton, silk, paper and similar fibrous material Wood, cotton, silk, paper and similar fibrous material not used as insulation - (15.2) rinted circuits rinted circuits used as internal connections complies with clause 14 - (15.3) lugs and socket-outlets used in SELV or ELV circuits No dangerous compatibility between output socketoutlet and a plug for socket-outlets for input circuit in relation to installation rules, voltages and frequencies lugs and socket-outlets for SELV comply with IEC and IEC TRF NO.: IEC60598_2_21A age 40 of 54 Report No.: ED S Ver.1.0

41 Attachment No.1 EN lugs and socket-outlets for SELV 3 A, 25 V r.m.s. or 60 V d.c. and 72 W comply with IEC and IEC or: - plugs not able to enter socket-outlets of other standardised system - socket-outlets not admit plugs of other standardised system - socket-outlets without protective earth 16 (16) CREEAGE DISTANCES AND CLEARANCES - (16) Creepage distances and clearances according to Table 3 and 4, as appropriate Controlgears providing SELV comply with L.1 in Annex L Insulating lining of metallic enclosures Basic insulation on printed boards tested according to clause 14 Distances subjected to both sinusoidal voltage as non-sinusoidal pulses not less than value in either Table 3 or 4 Creepage distances not less than minimum clearance 17 (17) SCREWS, CURRENT-CARRYING ARTS AND CONNECTIONS Screws, current-carrying parts and connections in compliance with IEC (clause numbers between parentheses refer to IEC ) (4.11) Electrical connections (4.11.1) Contact pressure (4.11.2) Screws: - self-tapping screws - thread-cutting screws (4.11.3) Screw locking: - spring washer - rivets (4.11.4) Material of current-carrying parts (4.11.5) No contact to wood or mounting surface (4.11.6) Electro-mechanical contact systems (4.12) Mechanical connections and glands (4.12.1) Screws not made of soft metal TRF NO.: IEC60598_2_21A age 41 of 54 Report No.: ED S Ver.1.0

42 Attachment No.1 EN Screws of insulating material Torque test: torque (Nm); part... : Torque test: torque (Nm); part... : Torque test: torque (Nm); part... : (4.12.2) Screws with diameter < 3 mm screwed into metal (4.12.4) Locked connections: - fixed arms; torque (Nm)... : - lampholder; torque (Nm)... : - push-button switches; torque 0,8 Nm... : (4.12.5) Screwed glands; force (Nm)... : 18 (18) RESISTANCE TO HEAT, FIRE AND TRACKING - (18.1) Ball-pressure test: - part tested; temperature ( C)... : See part - part tested; temperature ( C)... : - (18.2) Test of printed boards: - part tested... : See part - part tested... : - (18.3) Glow-wire test (650 C): - part tested... : See part - part tested... : - (18.4) Needle flame test (10 s): - part tested... : See part - part tested... : - (18.5) Tracking test: - part tested... : See part - part tested... : 19 (19) RESISTANCE TO CORROSION - test according of IEC adequate varnish on the outer surface 20 (-) ANNEXES Comply with appropriate annexes of IEC (see Annexes) TRF NO.: IEC60598_2_21A age 42 of 54 Report No.: ED S Ver.1.0

43 Attachment No.1 EN TABLE: tests of fault conditions art Simulated fault Hazard Varistor S-C, fuse open NO TRF NO.: IEC60598_2_21A age 43 of 54 Report No.: ED S Ver.1.0

44 Attachment No.1 EN (16) TABLES: Creepage distances and clearances Table 3 Minimum distances (mm) for a.c. (50/60 Hz) sinusoidal voltages RMS working voltage (V) not exceeding Creepage distances Required basic insulation, TI 600 0,6 0,8 1, ,5 Measured Required basic insulation, TI < 600 1,2 1,6 2, Measured 5.0 Required supplementary insulation TI 600-0,8 1, ,5 Measured Required supplementary insulation TI < 600-1,6 2, Measured Required reinforced insulation - 3, Measured 5.0 Clearances Required basic insulation 0,2 0,8 1, ,5 Measured 5.0 Required supplementary insulation - 0,8 1, ,5 Measured Required reinforced insulation - 1, Measured 5.0 Table 4 Minimum distances (mm) for non-sinusoidal pulse voltages Rated pulse voltage (peak kv) 2,0 2,5 3,0 4,0 5,0 6,0 8,0 Required clearances 1,0 1, ,5 8 Measured Rated pulse voltage (peak kv) Required clearances Measured Rated pulse voltage (peak kv) Required clearances Measured TRF NO.: IEC60598_2_21A age 44 of 54 Report No.: ED S Ver.1.0

45 Attachment No.1 EN A ANNEX A - TEST TO ESTABLISH WHETHER A CONDUCTIVE ART IS A LIVE ART WHICH MAY CAUSE AN ELECTRIC SHOCK A.1 Comply with A.2 or A.3 A.2 Voltage 35 V peak or 60 V d.c... : A.3 If voltage > 35 V r.m.s. or > 60 V d.c. or protective impendance device; touch current does not exceed 0,7 ma (peak) or 2 ma d.c.... : Comply with Annex G of IEC C ANNEX C ARTICULAR REQUIREMENTS FOR ELECTRONIC LAM CONTROLGEAR WITH MEANS OF ROTECTION AGAINST OVERHEATING C3 GENERAL REQUIREMENTS C3.1 Thermal protection means integral with the controlgear, protected against mechanical damage Renewable only by means of a tool If function depending on polarity, for cord-connected equipment protection means in both leads Thermal links comply with IEC Electrical controls comply with IEC C3.2 No risk of fire by breaking (clause C7) C5 CLASSIFICATION a) automatic resetting type b) manual resetting type c) non-renewable, non-resetting type d) renewable, non-resetting type e) other type of thermal protection; description.. : C6 MARKING C6.1 Symbol for temperature declared thermally protected controlgear C6.2 Declaration of the type of protection provided C7 LIMITATION OF HEATING C7.1 reselection test: Test sample placed for at least 12 h in an oven having temperature (tc - 5) K No operation of the protection device C7.2 Functioning of protection means: TRF NO.: IEC60598_2_21A age 45 of 54 Report No.: ED S Ver.1.0

46 Attachment No.1 EN Normal operation of the sample in a test enclosure according to Annex D at an ambient temperature such that (tc +0; -5) C is obtained No operation of the protection device Introducing of the most onerous test condition determined during test of clause 14 Output of windings connected to the mains supply short-circuited, and other part of the controlgear operated under normal conditions Increasing of the current through the windings continuously until operation of the protection means Continuous measuring of the highest surface temperature Controlgear according to C5 a) or C5 e) operated until stable conditions are achieved Automatic-resetting thermal protectors working 3 times Controlgear according to C5 b) working 6 times Controlgear according to C5 c) and C5) d) working once Highest temperature does not exceed the marked value Any overshoot of 10% over the marked value within 15 min D ANNEX D REQUIREMENTS FOR CARRY OUT THE HEATING TESTS OF THERMALLY ROTECTED LAM CONTROLGEAR Tests in C7 performed in accordance with Annex D, if applicable E ANNEX E USE OF CONSTANT S OTHER THAN 4500 IN t w TESTS Comply with tests according Annex E, if applicable F ANNEX F - DRAUGHT-ROOF ENCLOSURE Draught-proof enclosure in accordance with the description Dimensions of the enclosure Other design; description TRF NO.: IEC60598_2_21A age 46 of 54 Report No.: ED S Ver.1.0

47 Attachment No.1 EN H ANNEX H - TESTS All tests performed in accordance with the advice given in Annex H, if applicable I ANNEX I - ADDITIONAL REQUIREMENTS FOR BUILT-IN MAGNETIC BALLASTS WITH DOUBLE OR REINFORCED INSULATION Comply with tests according Annex I, if applicable TRF NO.: IEC60598_2_21A age 47 of 54 Report No.: ED S Ver.1.0

48 Attachment No.2 EN Clause Requirement Test Result Remark Verdict 13.2 Module withstands overpower condition >15 min. Module with automatic protective device or power limiter, test performed 15 min. at limit. During the tests, tissue paper, spread below module, does not ignite TRF NO.: IEC60598_2_21A age 48 of 54 Report No.: ED S Ver.1.0

49 Attachment No.3 IEC Clause Requirement Test Result Remark Verdict Item Tests according to IEC/TR 62778:2014 Symb Units Result Remark ol Correlated colour temperature CCT K / / x/y colour coordinates / / Blue light hazard radiance LB W/(m2 sr1) 33 / Blue light hazard irradiance EB W/m2 / / Luminance L cd/m e+004 / Illuminance E lx 321 / Supplementary information: TRF NO.: IEC60598_2_21A age 49 of 54 Report No.: ED S Ver.1.0

50 ictures Figure 1: Overview for model x-glo v Figure 2: Driver overview for model x-glo v TRF NO.: IEC60598_2_21A age 50 of 54 Report No.: ED S Ver.1.0

51 ictures Figure 3: Driver view for model x-glo v Figure 4: Driver front view for model x-glo v TRF NO.: IEC60598_2_21A age 51 of 54 Report No.: ED S Ver.1.0

52 ictures Figure 5: Driver rear view for model x-glo v Figure 6: Connector view for model x-glo v TRF NO.: IEC60598_2_21A age 52 of 54 Report No.: ED S Ver.1.0

53 ictures Figure 7: Connector view for model x-glo v Figure 8: Input view for model x-glo v TRF NO.: IEC60598_2_21A age 53 of 54 Report No.: ED S Ver.1.0

54 ictures Figure 9: The end view for model x-glo v ===================================END OF REORT============================== TRF NO.: IEC60598_2_21A age 54 of 54 Report No.: ED S Ver.1.0