CENTRE OF TESTING SERVICE INTERNATIONAL

Transcription

1 CETRE OF TESTIG SERVICE ITERATIOAL OERATE ACCORDIG TO ISO/IEC LVD TEST REORT TEST REORT UMBER : CGZ L-F GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China

2 Table of contents 1. General Information otes Tester Testing laboratory Application details Test item description Test standards 6 2. Technical test Summary of test results Test environment Conformity verification - Summary of inspection 8 3. Test Results articulars: test item vs. test requirements General requirements and results Annex as stated in the standards Tables 30 Attachments 36 GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 1 of 36 Date: 29 January 2015

3 1 General Information 1.1 otes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has assed all the relevant tests conforms to a specification (only telecommunication products). either is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that its performance generally conforms to representative cases of communications equipment. The test results of this test report relate exclusively to the item tested as specified in 1.5. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the Centre of Testing Service. GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 2 of 36 Date: 29 January 2015

4 1.2 Tester Tested by: 29 January 2015 Kate Zhang Date ame Signature Reviewed by: 29 January 2015 Rock Weng Date ame Signature Approved by: 29 January 2015 Jun Yang Date ame Signature GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 3 of 36 Date: 29 January 2015

5 1.3 Testing laboratory Location GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Telephone: Telefax : Test location, where different from CTS: ame:./. Street:./. Town:./. Country:./. Telephone:./. Fax:./. Teletex:./. 1.4 Client details Details of applicant ame : Guangzhou Osen Electrical Co., Ltd. Street : o. 1-2, Lanyue orth Street, Taishi, Town : Dongyong Town, anyu District, Guangzhou, Country : China Telephone : Fax : Teletex :./. Contact : Mr. eng Telephone : GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 4 of 36 Date: 29 January 2015

6 1.4.2 Details of manufacturer ame : Guangzhou Osen Electrical Co., Ltd. Street : o. 1-2, Lanyue orth Street, Taishi, Town : Dongyong Town, anyu District, Guangzhou, Country : China Telephone : Fax : Teletex :./. Contact : Mr. eng Telephone : Details of factory ame Street Town Country : Guangzhou Osen Electrical Co., Ltd. : o. 1-2, Lanyue orth Street, Taishi, : Dongyong Town, anyu District, Guangzhou, : China Dates of application Date of receipt of application : 05 January 2015 Date of receipt of test item : 05 January 2015 Date of test : 05 January January Test item Description Description of test item Type of product : pendent lamp Model/Type reference(test EUT) : Serial number : --- GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 5 of 36 Date: 29 January 2015

7 1.5.2 Test item particulars Test item... : pendent lamp Trade Mark... : OSE rotection Class... : Class I; Class II; Class III. Rated Voltage(Range)... : 230V~ Rated Frequency... : 50Hz; 60Hz; 50/60Hz; DC; Other: Rated Wattage... : 4 X MAX 28W I umber... : I20; I24; I65; Other: Supply Connection... : Type X; Type Y; Type Z; ins; Appliance inlet; Terminals; connecting leads (tails); Adaptors; connectors; Other: Lamp(s) type... : Tungsten filament lamps; Tungsten halogen lamps; Discharge lamps; Metal halide lamps; High-pressure sodium vapour lamps; Single-capped fluorescent lamps ; Double-capped fluorescent lamps; Self-ballasted lamps; Other: Luminaire Mobility... : Fixed Luminaires; ortable Luminaries; Recessed Luminaire; Track-mounted Luminaires; Semi-luminaires; Other: Mass of Equipment... : 3,2 kg. Instructions language... : English; French; Other: Mounting condition... : Luminaires suitable for direct mounting on normally flammable surfaces; ; ; Ambient Temperature... : t a = 25 C (all informations was provided by the applicant or detected at the sample) lease see also attachment 1.6 Test standards E : A11: 2009 Luminaires art 1: General requirements and tests (IEC : 2008 (Modified)) E : 1989 Luminaires-art 2: articular requirements-section 1:Fixed general purpose luminaries (IEC : A1: 1987) E 62493: 2010 Assessment of lighting equipment related to human exposure to electromagnetic fields GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 6 of 36 Date: 29 January 2015

8 2 Technical test 2.1 Summary of test results o deviations from the technical specification(s) were ascertained in the course of the tests performed. 2.2 Test environment Temperature: C Relative humidity content: % Air pressure: Details of power supply: ka V, AC Other parameters: --- GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 7 of 36 Date: 29 January 2015

9 2.3 Conformity verification - Summary of inspection Clause Summary of inspection Test result.a. ass Fail 3 Marking 4 Construction 5 External and internal wiring 7 rovisions for earthing 8 rotection against electric shock 9 Resistance to dust and moisture 10 Insulation resistance and electric strength 11 Creepage distances and clearances 12 Endurance tests and thermal tests 13 Resistance to heat, fire and tracking 14 Terminals 15 Screwless terminals and electrical connections Annexes Test case verdicts.a.: Test case does not apply to the test object ass: Test item does meet the requirement Fail: Test item does not meet the requirement GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 8 of 36 Date: 29 January 2015

10 3 Test results basic standard(s) 3.1 articulars: test item vs. Test requirements IEC and/or E art 2: articular requirements Section one Fixed general purpose luminaries E Assessment of lighting equipment related to human exposure to electromagnetic fields ossible test case verdicts: - test case does not apply to the test object...: (/A) - test object does meet the requirement...: (ass) - test object does not meet the requirement...: F(Fail) Test specification: Standard...: IEC : A1:1987 used in conjunction with IEC : 2008 E : 1989 used in conjunction with E : A11: 2009 E 62493: 2010 Test procedure... : LVD DOC approval. on-standard test method... : Test Report Form o... : Test Report Form(s) Originator... : /A IEC60598_2_1E Centre of Testing Service Master TRF... : Dated ov 2009 Copyright blank test report Centre of Testing Service General remarks: (see remark #) refers to a remark appended to the report. (see appended table) refers to a table appended to the report. Throughout this report a comma is used as the decimal separator. The test results presented in this report relate only to the object tested. This report shall not be reproduced except in full without the written approval of the testing laboratory. GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 9 of 36 Date: 29 January 2015

11 Copy of marking plate: GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 10 of 36 Date: 29 January 2015

12 3.2 General requirements and results IEC and/or E (0) GEERAL TEST REQUIREMETS 1.2 (0.1) Information for luminaire design considered Standard Yes o 1.2 (0.3) More sections applicable...: Yes o 1.4 (2) CLASSIFICATIO 1.4 (2.2) Type of protection...: Class I 1.4 (2.3) Degree of protection...: I (2.4) Luminaires suitable for direct mounting on normally flammable surfaces...: Luminaires not suitable for direct mounting on normally flammable surfaces...: Yes o Yes o 1.4 (2.5) Luminaire for normal use...: Yes o Luminaire for rough service...: Yes o 1.5 (3) MARKIG 1.5 (3.2) Mandatory markings osition of the marking Format of symbols/text Text=2mm, symbol=5mm 1.5 (3.3) Additional information Language of instructions English 1.5 (3.3.1) Combination luminaires 1.5 (3.3.2) ominal frequency in Hz 50Hz 1.5 (3.3.3) Operating temperature 1.5 (3.3.4) Symbol or warning notice 1.5 (3.3.5) Wiring diagram 1.5 (3.3.6) Special conditions 1.5 (3.3.7) Metal halide lamp luminaire warning 1.5 (3.3.8) Limitation for semi-luminaires 1.5 (3.3.9) ower factor and supply current 1.5 (3.3.10) Suitability for use indoors 1.5 (3.3.11) Luminaires with remote control GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 11 of 36 Date: 29 January 2015

13 IEC and/or E (3.3.12) Clip-mounted luminaire warning 1.5 (3.3.13) Specifications of protective shields 1.5 (3.3.14) Symbol for nature of supply ~ 1.5 (3.3.15) Rated current of socket outlet 1.5 (3.3.16) Rough service luminaire 1.5 (3.3.17) Mounting instruction for type Y, type Z and some type X attachments Type Y attachments 1.5 (3.3.18) on-ordinary luminaires with VC cable 1.5 (3.3.19) For luminaires which generate a protective conductor current greater than 10 ma and intended for permanent connection 1.5 (3.3.20) Wall mounted and adjustable luminaires not intended to be mounted within arms reach 1.5 (3.4) Test with water Test with hexane Legible after test Label attached 1.6 (4) COSTRUCTIO 1.6 (4.2) Components replaceable without difficulty 1.6 (4.3) Wireways smooth and free from sharp edges 1.6 (4.4) Lampholders 1.6 (4.4.1) Integral lampholder 1.6 (4.4.2) Wiring connection 1.6 (4.4.3) Lampholder for end-to-end mounting 1.6 (4.4.4) ositioning - pressure test ()...: - bending test (m)...: 1.6 (4.4.5) eak pulse voltage 1.6 (4.4.6) Centre contact 1.6 (4.4.7) arts in rough service luminaires resistant to tracking 1.6 (4.4.8) Lamp connectors 1.6 (4.4.9) Caps and bases correctly used G9 1.6 (4.5) Starter holders Starter holder in luminaires other than class II o such parts GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 12 of 36 Date: 29 January 2015

14 IEC and/or E Starter holder class II construction 1.6 (4.6) Terminal blocks Tails Unsecured blocks 1.6 (4.7) Terminals and supply connections 1.6 (4.7.1) Contact to metal parts 1.6 (4.7.2) Test 8 mm live conductor Test 8 mm earth conductor 1.6 (4.7.3) Terminals for supply conductors 1.6 ( ) Welded connections: - stranded or solid conductor - spot welding - welding between wires - Type Z attachment - mechanical test according to electrical test according to heat test according to and (4.7.4) Terminals other than supply connection 1.6 (4.7.5) Heat-resistant wiring/sleeves 1.6 (4.7.6) Multi-pole plug - test at (4.8) Switches: - adequate rating - adequate fixing - polarized supply 1.6 (4.9) Insulating lining and sleeves 1.6 (4.9.1) Retainment Method of fixing...: Reliably retained in position 1.6 (4.9.2) Insulated linings and sleeves a) & c) Insulation resistance and electric strength b) Ageing test. Temperature ( C)...: 1.6 (4.10) Insulation of Class II luminaires 1.6 (4.10.1) o contact, mounting surface accessible metal parts wiring of basic insulation Safe installation fixed luminaires Class II construction GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 13 of 36 Date: 29 January 2015

15 IEC and/or E Capacitors and switches Interference suppression capacitors according to IEC (4.10.2) Assembly gaps: - not coincidental Class II construction - no straight access with test probe 1.6 (4.10.3) Retainment of insulation: - fixed Class II construction - unable to be replaced; luminaire inoperative - sleeves retained in position - lining in lampholder 1.6 (4.11) Electrical connections 1.6 (4.11.1) Contact pressure 1.6 (4.11.2) Screws: - self-tapping screws - thread-cutting screws - at least two self-tapping screws 1.6 (4.11.3) Screw locking: - spring washer - rivets 1.6 (4.11.4) Material of current-carrying parts 1.6 (4.11.5) o contact to wood 1.6 (4.11.6) Electro-mechanical contact systems 1.6 (4.12) Mechanical connections and glands 1.6 (4.12.1) Screws not made of soft metal Screws of insulating material Torque test: torque (m); part...: Screws fixed the cord anchorage; 0,5m Torque test: torque (m); part...: Torque test: torque (m); part...: 1.6 (4.12.2) Screws with diameter < 3 mm screwed into metal 1.6 (4.12.4) Locked connections: - fixed arms; torque (m)...: M10; 2,5m - lampholder; torque (m)...: - push-button switches; torque 0,8 m...: GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 14 of 36 Date: 29 January 2015

16 IEC and/or E (4.12.5) Screwed glands; torque (m)...: 1.6 (4.13) Mechanical strength 1.6 (4.13.1) Impact tests: - fragile parts; energy (m)...: - other parts; energy (m)...: Body; 0,35m 1) live parts 2) linings 3) protection 4) covers 1.6 (4.13.3) Straight test finger 1.6 (4.13.4) Rough service luminaires - I54 or higher a) fixed b) hand-held c) delivered with a stand d) for temporary installations and suitable for mounting on a stand 1.6 (4.13.6) Tumbling barrel 1.6 (4.14) Suspensions and adjusting devices 1.6 (4.14.1) Mechanical load: (-) A) Four times the weight 4X3,2 Kg =12,8 Kg B) torque 2,5 m C) bracket arm; bending moment (m)...: D) load track-mounted luminaires E) clip-mounted luminaires, glass-shelve. Thickness (mm)...: metal rod. diameter (mm)...: 1.6 (4.14.2) Load to flexible cable 1.6 ( a) Mass (kg)...: 1,2 kg Stress in conductors (/mm²)...: 8 /mm² Mass (kg) of semi-luminaire...: Bending moment (m) of semi-luminaire...: Adjusting devices: - flexing test; number of cycles...: GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 15 of 36 Date: 29 January 2015

17 IEC and/or E ( b) 1.6 ( c) - strands broken - electric strength test afterwards Luminaires with a means of adjustment intended to be installed within arms reach, shall allow the operation of its intended function without impairing the stability of the luminaire or causing deformation of any part of the construction, nor cause injury due to temperatures above those specified in Table For luminaires intended to be mounted within arms reach, the space surrounding any means of adjustment, except the light beam aperture, up to 5 cm away from the means of adjustment in any direction, shall comply with the temperature limits for the means of adjustment, as specified in Table (4.14.4) Telescopic tubes: cords not fixed to tube; no strain on conductors 1.6 (4.14.5) Guide pulleys 1.6 (4.14.6) Strain on socket-outlets 1.6 (4.15) Flammable materials: - glow-wire test 650 C - spacing 30 mm - screen withstanding test of screen dimensions - no fiercely burning material - thermal protection - electronic circuits exempted 1.6 (4.15.2) Luminaires made of thermoplastic material with lamp control gear a) construction b) temperature sensing control c) surface temperature 1.6 (4.16) Luminaires for mounting on normally flammable surfaces o lamp control gear (compliance with Section 12) 1.6 (4.16.1) Lamp control gear spacing: - spacing 35 mm - spacing 10 mm 1.6 (4.16.2) Thermal protection: GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 16 of 36 Date: 29 January 2015

18 IEC and/or E in lamp control gear - external - fixed position - temperature marked lamp control gear 1.6 (4.16.3) be so designed that it satisfies the test of 12.6 (see 12.6) 1.6 (4.17) Drain holes Clearance at least 5 mm 1.6 (4.18) Resistance to corrosion: 1.6 (4.18.1) - rust-resistance I (4.18.2) - season cracking in copper 1.6 (4.18.3) - corrosion of aluminium 1.6 (4.19) Ignitors compatible with ballast 1.6 (4.20) Rough service vibration 1.6 (4.21) rotective shield: 1.6 (4.21.1) Shield fitted 1.6 (4.21.2) articles from a shattering lamp not impair safety 1.6 (4.21.3) o direct path 1.6 (4.21.4) Impact test on shield Glow-wire test on lamp compartment 1.6 (4.22) Attachments to lamps 1.6 (4.23) Semi-luminaires comply Class II 1.6 (4.24) UV radiation, metal halide lamps 1.6 (4.25) o sharp point or edges 1.6 (4.26) Short-circuit protection: 1.6 (4.26.1) Uninsulated accessible SELV parts 1.6 (4.26.2) Short-circuit test 1.6 (4.26.3) Test chain according to Figure (4.27) Terminal blocks with integrated screwless earthing contacts 1.7 (11) CREEAGE DISTACES AD CLEARACES Working voltage (V)...: 230V~ Voltage form Sinusoidal on-sinusoidal TI < 600 > 600 GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 17 of 36 Date: 29 January 2015

19 IEC and/or E Rated pulse voltage (kv)...: --- (1) Current-carrying parts of different polarity: cr (mm); cl (mm)...: (2) Current-carrying parts and accessible parts: cr (mm); cl (mm)...: (3) arts becoming live due to breakdown of basic insulation and metal parts: cr (mm); cl (mm)...: (4) Outer surface of cable where it is clamped and metal parts: cr (mm); cl (mm)...: Cr>2,5mm,Cl>1,5mm (limit:cr:2,5,cl:1,5mm) Cr>2,5mm,Cl>1,5mm (limit:cr:2,5,cl:1,5mm) (5) ot used (6) Current-carrying parts and supporting surface: cr (mm); cl (mm)...: Cr>2,5mm,Cl>1,5mm (limit:cr:2,5,cl:1,5mm) 1.8 (7) ROVISIO FOR EARTHIG 1.8 ( ) 1.8 ( ) Accessible metal parts Metal parts in contact with supporting surface Resistance < 0,5 Ω 0,041Ω Two self-tapping screws used Thread-forming screws Thread-forming screw used in a grove Earth makes contact first For terminal blocks with integrated screwless earthing contacts, the additional tests of Annex V are to be applied Earth continuity in joints etc. 1.8 (7.2.4) Locking of clamping means Compliance with For terminal blocks with integrated screwless earthing contacts, the additional tests of Annex V apply 1.8 (7.2.5) Earth terminal integral part of connector socket 1.8 (7.2.6) Earth terminal adjacent to mains terminals 1.8 (7.2.7) Electrolytic corrosion of the earth terminal 1.8 (7.2.8) Material of earth terminal GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 18 of 36 Date: 29 January 2015

20 IEC and/or E Contact surface bare metal 1.8 (7.2.10) Class II luminaire for looping-in Double or reinforced insulation to functional earth 1.8 (7.2.11) Earthing core coloured green-yellow Length of earth conductor 1.9 (14) SCREW TERMIALS Separately approved; component list (see Annex 1) art of the luminaire (see Annex 3) 1.9 (15) SCREWLESS TERMIALS Separately approved; component list (see Annex 1) art of the luminaire (see Annex 4) (-) Springtype screwless terminals of the Type b shall not be used 1.10 (5) EXTERAL AD ITERAL WIRIG 1.10 (5.2) Supply connection and external wiring 1.10 (5.2.1) Means of connection...: Terminal - devices for the connection of luminaires - plugs for engagement with socket-outlets - terminal block specified - connecting leads and elevant information provided (E) - supply cords - adapters - appliance inlets - compliance with 4.6, 4.7.1, 4.7.2, , 11.2, 12 and 13.2 of art (5.2.2) Type of cable...: Cables equal to HD 21 S2 or HD22 S2 (E) ominal cross-sectional area (mm²)...: 1.10 (5.2.3) Type of attachment, X, Y or Z Type Y attachment 1.10 (5.2.5) Type Z not connected to screws 1.10 (5.2.6) Cable entries: GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 19 of 36 Date: 29 January 2015

21 IEC and/or E suitable for introduction - adequate degree of protection 1.10 (5.2.7) Cable entries through rigid material have rounded edges 1.10 (5.2.8) Insulating bushings: - suitably fixed - material in bushings - material not likely to deteriorate - tubes or guards made of insulating material 1.10 (5.2.9) Locking of screwed bushings 1.10 (5.2.10) Cord anchorage: 1.10 ( ) 1.10 ( ) 1.10 ( ) - covering protected from abrasion - clear how to be effective - no mechanical or thermal stress - no tying of cables into knots etc. - insulating material or lining Cord anchorage for type X attachment: a) at least one part fixed b) types of cable c) no damaging of the cable d) whole cable can be mounted e) no touching of clamping screws f) metal screw not directly on cable g) replacement without special tool Glands not used as anchorage Labyrinth type anchorages Adequate cord anchorage for type Y and type Z attachment Tests: GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Type Y attachment - impossible to push cable; unsafe - pull test: 25 times; pull ()...: 60 - torque test: torque (m)...: 0,15 - displacement 2 mm 0,9mm - no movement of conductors Report o.: CGZ L-F age 20 of 36 Date: 29 January 2015

22 IEC and/or E no damage of cable or cord 1.10 (5.2.11) External wiring passing into luminaire 1.10 (5.2.12) Looping-in terminals 1.10 (5.2.13) Wire ends not tinned Wire ends tinned: no cold flow 1.10 (5.2.14) Mains plug same protection Class III luminaire plug 1.10 (5.2.16) Appliance inlets (IEC 60320) Appliance couplers of class II type 1.10 (5.2.17) on standardized interconnecting cables properly assembled 1.10 (5.2.18) Used plug in accordance with: - IEC other standard 1.10 (5.3) Internal wiring 1.10 (5.3.1) Internal wiring of suitable size and type 1.10 ( ) 1.10 ( ) 1.10 ( ) 1.10 ( ) Through wiring - not delivered/ mounting instruction - factory assembled - socket outlet loaded (A)...: - temperatures...: (see Annex 2) Green-yellow for earth only Internal wiring connected directly to fixed wiring Cross-sectional area (mm²)...: 0,75 mm² Insulation thickness Extra insulation added where necessary Internal wiring connected to fixed wiring via internal current-limiting device Adequate cross-sectional area and insulation thickness Double or reinforced insulation for class II Conductors without insulation GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 21 of 36 Date: 29 January 2015

23 IEC and/or E ( ) 1.10 ( ) SELV current-carrying parts Insulation thickness other than VC or rubber 1.10 (5.3.2) Sharp edges etc. o moving parts of switches etc. Joints, raising/lowering devices Telescopic tubes etc. o twisting over (5.3.3) Insulating bushings: - suitable fixed - material in bushings - material not likely to deteriorate - cables with protective sheath 1.10 (5.3.4) Joints and junctions effectively insulated 1.10 (5.3.5) Strain on internal wiring 1.10 (5.3.6) Wire carriers 1.10 (5.3.7) Wire ends not tinned Wire ends tinned: no cold flow 1.11 (8) ROTECTIO AGAIST ELECTRIC SHOCK 1.11 (8.2.1) Live parts not accessible Basic insulated parts not used on the outer surface without appropriate protection o access to live parts with the standard test finger is permitted Lampholders and starterholders shall comply to the electrical strength test and creepage distance and clearance requirements for double or reinforced insulation Basic insulation may be accessible when the luminaire is opened for lamp or starter replacement Component comply with the relevant requirements applied to an independent component Double-ended tungsten filament lamp Insulation lacquer not reliable Double-ended high pressure discharge lamp GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 22 of 36 Date: 29 January 2015

24 IEC and/or E Relevant warning according to fitted to the luminaire 1.11 (8.2.2) ortable luminaire adjusted in most unfavourable position 1.11 (8.2.3 a) 1.11 (8.2.3 b) 1.11 (8.2.3 c) For protection against electric shock: - basic insulated metal parts not accessible during starter or lamp replacement - basic insulation not accessible other than during starter or lamp replacement - glass protective shields not used as supplementary insulation Class I luminaire with BC lampholder Class III luminaires may have exposed current carrying parts in the SELV circuit under the following conditions Class III luminaires are accepted only for connection to a SELV source 1.11 (8.2.4) ortable luminaire: - protection independent of supporting surface - terminal block completely covered 1.11 (8.2.5) Compliance with the standard test finger or relevant probe 1.11 (8.2.6) Covers reliably secured 1.11 (8.2.7) Discharging of capacitors 0,5 μf ortable plug connected luminaire with capacitor Other plug connected luminaire with capacitor Discharge device on or within capacitor Discharge device mounted separately 1.12 (12) EDURACE TEST AD THERMAL TEST (-) The housing temperatures shall not exceed 1.12 (12.3) Endurance test: - mounting-position...: As in normal used - test temperature ( C)...: 35 C - total duration (h)...: 240h - supply voltage: Un factor; calculated voltage (V)...: 232,7V GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 23 of 36 Date: 29 January 2015

25 IEC and/or E lamp used...: See data sheet 1.12 (12.3.2) After endurance test: - no part unserviceable - luminaire not unsafe - no damage to track system - marking legible - no cracks, deformation etc (12.4) Thermal test (normal operation) (see Annex 2) 1.12 (12.5) Thermal test (abnormal operation) (see Annex 2) 1.12 (12.6) Thermal test (failed lamp control gear condition): 1.12 (12.6.1) Through wiring or looping-in wiring loaded by a current of (A)...: - case of abnormal conditions...: - electronic lamp control gear - measured winding temperature ( C): at 1,1 Un - measured mounting surface temperature ( C) at 1,1 Un...: - calculated mounting surface temperature ( C)...: - track-mounted luminaires 1.12 (12.6.2) Temperature sensing control - case of abnormal conditions...: - thermal link - manual reset cut-out - auto reset cut-out - measured mounting surface temperature ( C)...: - track-mounted luminaires 1.12 (12.7) Thermal test (failed lamp control gear in plastic luminaires): 1.12 ( ) 1.12 ( ) Test for luminaires incorporating fluorescent lamps 70 W Through wiring or looping-in wiring loaded by a current of (A)...: - case of abnormal conditions.: - test for 4h at 1.1 Un...: If more than one ballast is used inside the luminaire GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 24 of 36 Date: 29 January 2015

26 IEC and/or E ( ) 1.12 ( ) 1.12 ( ) 1.12 ( ) 1.12 ( ) - only one in fault condition, until ballast failure occurs, test voltage.: Following the test - the components have been retained in place - arts of the luminaire enclosure continue to protect live parts against access with the standard test finger Test for luminaires with discharge lamps, fluorescent lamps >70 W, transformers >10 VA Through wiring or looping-in wiring loaded by a current of (A)...: - case of abnormal conditions.: - measured winding temperature ( C): at 1,1 Un...: - measured temperature of fixing point/ exposed part ( C): at 1,1 Un...: - calculated temperature of fixing point/ exposed part ( C)...: The thermoplastic material is then subjected to the ball pressure test as described in at the estimated temperature determined by linear regression, but not less than 75 C. - part tested; temperature ( C)... : - part tested; temperature ( C)... : Test for luminaires with short circuit proof transformers 10 VA Through wiring or looping-in wiring loaded by a current of (A)...: - case of abnormal conditions.: Following the test - arts of the luminaire enclosure continue to protect live parts against access with the standard test finger 1.12 (12.7.2) Temperature sensing control - thermal link - manual reset cut-out - auto reset cut-out - measured temperature of fixing point/ exposed part ( C):...: GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 25 of 36 Date: 29 January 2015

27 IEC and/or E (9) RESISTACE TO DUST, SOLID OBJECTS AD MOISTURE 1.13 (9.2) Tests for ingress of dust, solid objects and moisture: - classification according to I...: I 20 - mounting position during test...: As in normal used - fixing screws tightened; torque (m)...: tests according to clauses...: Cl of E electric strength test afterwards a) no deposit in dust-proof luminaire b) no talcum in dust-tight luminaire c) no trace of water on current-carrying parts or where it could become a hazard d) i) For luminaires without drain holes no water entry d) ii) For luminaires with drain holes no hazardous water entry e) no water in watertight luminaire f) no contact with live parts (I 2X) f) no entry into enclosure (I 3X and I 4X) f) no contact with live parts (I 3X and I 4X) g) no trace of water on any part of a lamp h) no damage 1.13 (9.3) Humidity test 48 h 30,95%Humidity 1.14 (10) ISULATIO RESISTACE AD ELECTRIC STREGTH 1.14 (10.2.1) Insulation resistance test Cable or cord covered by metal foil or replaced by a metal rod of mm Ø...: Insulation resistance (MΩ) SELV: - between current-carrying parts of different polarity...: - between current-carrying parts and mounting surface...: - between current-carrying parts and metal parts of the luminaire...: GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 26 of 36 Date: 29 January 2015

28 IEC and/or E between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts...: - insulating bushings as described in Section 5...: Other than SELV: - between live parts of different polarity...: >50 MΩ - between live parts and mounting surface...: >50 MΩ - between live parts and metal parts...: >50 MΩ - between live parts of different polarity through action of a switch...: - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts...: >50 MΩ - insulating bushings as described in Section 5...: 1.14 (10.2.2) Electric strength test Dummy lamp Luminaires with ignitors after 24 h test Luminaires with manual ignitors Test voltage (V): SELV: - between current-carrying parts of different polarity...: - between current-carrying parts and mounting surface...: - between current-carrying parts and metal parts of the luminaire...: - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts...: - insulating bushings as described in Section 5...: Other than SELV: - between live parts of different polarity...: 1460V/MI - between live parts and mounting surface...: 1460V/MI - between live parts and metal parts...: 1460V/MI - between live parts of different polarity through action of a switch...: GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 27 of 36 Date: 29 January 2015

29 IEC and/or E between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts...: 1460V/MI - insulating bushings as described in Section 5...: 1.14 (10.3.1) Touch current or protective conductor current and electric burn (ma)...: Touch current: 0,026mA 1.15 (13) RESISTACE TO HEAT, FIRE AD TRACKIG 1.15 (13.2.1) Ball-pressure test: - part tested; temperature ( C)...: Terminal; 125 C; 0,9mm - part tested; temperature ( C)...: 1.15 (13.3.1) eedle flame test (10 s): - part tested...: Terminal - part tested...: 1.15 (13.3.2) Glow-wire test (650 C): - part tested...: Insulation lining - part tested...: 1.15 (13.4.1) Tracking test: part tested...: GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 28 of 36 Date: 29 January 2015

30 3.3 Annex as stated in the standards IEC and/or E W AEX W, Alternative thermal test for thermoplastic luminaires W.1 Thermal test in regard to fault conditions in lamp controlgear or electronic devices without temperature sensing controls in thermoplastic luminaires for fluorescent lamps 70W Thermal test (failed lamp control gear in plastic luminaires): Through wiring or looping-in wiring loaded by a current of (A)... : - case of abnormal conditions.: - measured winding temperature ( C): at 1,1 Un... : - measured temperature of fixing point/ exposed part ( C): at 1,1 Un... : - calculated temperature of fixing point/ exposed part ( C)... : ZB AEX ZB, SECIAL ATIOAL CODITIOS (E) (2.2) Class 0 not accepted (3.3) DK: power supply cord with label IT: warning label on Class 0 luminaire (4.5.1) DK: socket-outlets (5.2.1) CY, DK, FI, SE, GB: type of plug ZC AEX ZC, ATIOAL DEVIATIOS (E) (4 & 5) FR: Shuttered socket-outlets 10/16A (13.3) DK: eedle flame test during 30 s (13.3) GB: Requirements according to United Kingdom Building Regulation (13.3.2) FR: Glow-wire test 850 C alt. 750 C for luminaires in premises open to public or 960 C for luminaires in emergency exits AEX EMF Requirements standard E 62493:2010 GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 29 of 36 Date: 29 January 2015

31 3.4 Tables IEC and/or E AEX 1: components object/part o. code manufacturer/ trademark type/model technical data standard Terminal B Zhongshan Hongyue Lighting Electrical Appliance Factory Alt. D Shenzhen Green Way Electronic Co., Ltd External wire Closed-end terminal Heat shrinkable tube mark(s) of conformity A8 450 V; T110; 24 A; 0,5-2,5 mm VDE A8 450 V; 0,5-4,0mm2; 110 C -- EEC 05 DEKRA B Guangdong Haerkn H05SS-K 1*0.75 mm 2 -- VDE C Heavy ower Co., Ltd. CE2 CE1 C Changyuan Electronics (Shenzhen) Co., Ltd. Alt. D Dongguan Salipt Co., Ltd. Alt. D Shenzhen Woer Heatshrinkable Material Co., Ltd. Internal wire (doubleinsulated) B Yang Tai Wire & Cable Co., Ltd. Alt. D Guangzhou Feng Tai Electronic Co., Ltd. CB-HFT Black; 600 V; 125 C; VW-1 SALIT S UL E Tested with appliance Black; 600 V; 125ºC; VW-1 RSFR-H Black; 600 V; 125ºC; VW-1 FE/FE FT-FE-102 FE single core non-sheathed cable for internal wiring, doubleinsulated; 300/500 V; 180 C; 20AWG- 18AWG ( mm²) FE single core non-sheathed cable for internal wiring, doubleinsulated; 300/500 V; 180 C; 20AWG- 18AWG ( mm²) --- UL E UL E UL E VDE VDE GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 30 of 36 Date: 29 January 2015

32 Alt. D Guangdong Haerkn ew Energy Co., Ltd. Alt. D Dong Guan istar Transmitting Technology Co., Inc FE single core non-sheathed cable for internal wiring, doubleinsulated; 300/500 V; 180 C; 20AWG- 18AWG ( mm²) 7022 FE single core non-sheathed cable for internal wiring, doubleinsulated; 300/500 V; 180 C; 20AWG- 18AWG ( mm²) Alt. D Various Various double-insulated; 300/500 V; 180 C; 20AWG-18AWG ( mm²) Lampholder B Eon Rise Electrical Appliances Factory Alt. D Yarncin Lighting Technology Co. Ltd. Alt. D Kangrong Fine Ceramic Co., Ltd. --- VDE VDE VDE Various FT9A 250 V; 2 A; 250 C --- VDE YX03D 250 V; 2 A; 250 C --- VDE K540M 250 V; 2 A; 250 C SEMKO EEC 14 SE/ The codes above have the following meaning: A - The component is replaceable with another one, also certified, with equivalent characteristics B - The component is replaceable if authorised by the test house C - Integrated component tested together with the appliance D - Alternative component GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 31 of 36 Date: 29 January 2015

33 IEC and/or E AEX 2: temperature measurements, thermal tests of Section 12 Type reference... : Lamp used... : G9 4X28W Lamp control gear used... : --- Mounting position of luminaire... : As in normal used Supply wattage (W)... : 117,6W Supply current (A)... : 0,513A Calculated power factor... : 1,0 Table: measured temperatures corrected for ta = 25 C: - abnormal operating mode... : test 1: rated voltage... : test 2: 1,06 times rated voltage or 1,05 times 229,8V(1,05 times rated rated wattage... : wattage) - test 3: Load on wiring to socket-outlet, 1,06 times voltage or 1,05 times wattage... : - test 4: 1,1 times rated voltage or 1,05 times rated wattage... : Through wiring or looping-in wiring loaded by a current of A during the test... : temperature ( C) of part Clause 12.4 normal Clause 12.5 abnormal test 1 test 2 test 3 limit test 4 limit External wiring , Internal wire , Lampholder , Terminal ,3 --- For Cl Closed-end terminal ,1 --- For Cl Mounting surface , GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 32 of 36 Date: 29 January 2015

34 IEC and/or E AEX 3: screw terminals (part of the luminaire) (14) SCREW TERMIALS (14.2) Type of terminal... : Rated current (A)... : ( ) One or more conductors ( ) Special preparation ( ) Terminal size Cross-sectional area (mm²)... : (14.3.3) Conductor space (mm)... : (14.4) Mechanical tests (14.4.1) Minimum distance (14.4.2) Cannot slip out (14.4.3) Special preparation (14.4.4) ominal diameter of thread (metric ISO thread)... : External wiring o soft metal (14.4.5) Corrosion (14.4.6) ominal diameter of thread (mm)... : Torque (m)... : (14.4.7) Between metal surfaces Lug terminal Mantle terminal ull test; pull ()... : (14.4.8) Without undue damage GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 33 of 36 Date: 29 January 2015

35 IEC and/or E AEX 4: screwless terminals (part of the luminaire) (15) SCREWLESS TERMIALS (15.2) Type of terminal... : Rated current (A)... : (15.3.1) Material (15.3.2) Clamping (15.3.3) Stop (15.3.4) Unprepared conductors (15.3.5) ressure on insulating material (15.3.6) Clear connection method (15.3.7) Clamping independently (15.3.8) Fixed in position ( ) Conductor size Type of conductor (15.5.1) Terminals internal wiring ( ) ull test spring-type terminals (4, 4 samples).: ( ) ull test pin or tab terminals (4, 4 samples) : Insertion force not exceeding 50 (15.5.2) ermanent connections: pull-off test (20 ) (15.6) Electrical tests Voltage drop (mv) after 1 h (4 samples)... : Voltage drop of two inseparable joints umber of cycles... : Voltage drop (mv) after 10th alt. 25th cycle (4 samples)... : Voltage drop (mv) after 50th alt. 100th cycle (4 samples)... : After ageing, voltage drop (mv) after 10th alt. 25th cycle (4 samples)... : After ageing, voltage drop (mv) after 50th alt. 100th cycle (4 samples)... : (15.7) Terminals external wiring Terminal size and rating GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 34 of 36 Date: 29 January 2015

36 IEC and/or E (15.8.1) ull test spring-type terminals or welded connections (4 samples); pull ()... : ull test pin or tab terminals (4 samples); pull ()... : (15.9) Contact resistance test Voltage drop (mv) after 1 h terminal voltage drop (mv) Voltage drop of two inseparable joints Voltage drop after 10th alt. 25th cycle --- Max. allowed voltage drop (mv)...: terminal voltage drop (mv) Voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)...: terminal voltage drop (mv) Continued ageing: voltage drop after 10th alt. 25th cycle Max. allowed voltage drop (mv)...: terminal voltage drop (mv) Continued ageing: voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)...: terminal voltage drop (mv) GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 35 of 36 Date: 29 January 2015

37 Attachments hoto document BOM CDF (critical data form) Copies of certificates of certified components Instruction manual Circuit diagram Explosion block Other if necessary end of report GZ test site: A101, o.65, Zhuji Road, Tianhe District, Guangzhou, Guangdong, China Report o.: CGZ L-F age 36 of 36 Date: 29 January 2015

38 Attachment age 1 of 4 Type Designation: pendent lamp, Report umber: CGZ L-F Marking position Figure 1 (External view - top) Figure 2(Internal construction 1)

39 Attachment age 2 of 4 Type Designation: pendent lamp, Report umber: CGZ L-F Figure 3 (Internal construction 2) Figure 4 (Internal construction 3)

40 Attachment age 3 of 4 Type Designation: pendent lamp, Report umber: CGZ L-F Figure 5 (Internal construction 4) Figure 6 (Cord anchorage)

41 Attachment age 4 of 4 Type Designation: pendent lamp, Report umber: CGZ L-F Figure 7 (Lampholder)