TEST REPORT IEC Luminaires Part 2: Particular requirements: Section One Fixed general purpose luminaires

Transcription

1 Test Report issued under the responsibility of: TEST REORT IEC Luminaires art 2: articular requirements: Section One Fixed general purpose luminaires Report Number.... : Date of issue... : Total number of pages pages Applicant s name... : Address... : AGC Lighting Co., Ltd 2nd Floor, 2nd Building, DingFeng High-Tech Zone, Fuyuan 1st Road, Fu Yong Sub-district, Bao An, ShenZhen, Guangdong, China Test specification: Standard... : Test procedure... : Non-standard test method..: IEC : A1:1987 used in conjunction with IEC :2008 CB Scheme Test Report Form No.... : Test Report Form(s) Originator... : Master TRF... : IEC60598_2_1C Intertek Semko AB Copyright 2012 Worldwide System for Conformity Testing and Certification of Electrotechnical Equipment and Components (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. If this Test Report Form is used by non-iecee members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02. Test item description... : Trade Mark... : LED High Bay Light Manufacturer... : Model/Type reference... : Ratings... : AGC Lighting Co., Ltd 2nd Floor, 2nd Building, DingFeng High-Tech Zone, Fuyuan 1st Road, Fu Yong Sub-district, Bao An, ShenZhen, Guangdong, China See model list V~, 50/60Hz (See general production for details)

2

3 age 3 of 50 Report No.: List of Attachments (including a total number of pages in each attachment): Attachment 1: CB report of IEC 62471: Summary of testing: Tests performed (name of test and test clause): Full test were done on model AGC-HB and AGC-HB as representative, partial tests were done on other models. This report includes the following parts: - All clauses of IEC :2008 and IEC :1979 +A1. - Annex 5: European Group Differences and National Differences. - Annex 6: LED modules for general lighting Safety specifications IEC/EN 62031:2008+A1. - Annex 7: Variations to IEC :2008 for application in Australia and/or New Zealand (AS/NZS :2013) - Annex 8: Variations to AS/NZS :1998 for application in Australia and/or New Zealand (AS/NZS :2014) - Annex 9: Australian national differences of AS/NZS IEC : Annex 10: hotobiological safety of lamps and lamp systems were evaluated according to standard IEC 62471:2006 and EN 62471: hoto document Summary of compliance with National Differences: List of countries addressed: AU=Australian, DE=Germany Testing location: TÜVRheinland (Shenzhen) Co., Ltd. 3&4 F, Cybio Technology Building No. 1, Langshan No. 2 Road South, 5th Industrial Area, High-Tech Industry ark North, Nanshan District, , Shenzhen,. R. China The product fulfils the requirements of EN : A11: 2009, EN : 1989, AS/NZS : 2013, AS/NZS : 2014.

4 Copy of marking plate age 4 of 50 Report No.: The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks. Test item particulars... : Classification of installation and use... : Supply Connection... :... :... : LED High Bay Light Supply cord ossible test case verdicts: - test case does not apply to the test object... : - test object does meet the requirement... : (ass) - test object does not meet the requirement... : F (Fail) Testing... : Date of receipt of test item... : Date (s) of performance of tests... : to

5 General remarks: age 5 of 50 Report No.: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Throughout this report a comma / point is used as the decimal separator. Clause numbers between brackets refer to clauses in IEC Manufacturer s Declaration per sub-clause of IECEE 02: The application for obtaining a CB Test Certificate includes more than one factory location and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided... : Yes Not applicable When differences exist; they shall be identified in the General product information section. Name and address of factory (ies)... : AGC Lighting Co., Ltd 2nd Floor, 2nd Building, DingFeng High-Tech Zone, Fuyuan 1st Road, Fu Yong Sub-district, Bao An, ShenZhen, Guangdong, China General product information: roduct: LED High Bay Light Rating: V~, 50/60Hz, ta=50 C Class I, I65, suitable for direct mounting on normally flammable surfaces. 1. All models have the similar appearance and construction, but different dimension, power and LED quantities. 2. All models use approved independent SELV LED driver, and the no load output voltages of LED driver is max.49vdc. 3. All models have the same type of LED chip with CCT. of 5000K. Model list Model ower (W) LED Driver AGC-HB LED quantities (pcs) 112 Dimension (mm) AGC-HB HBG A AGC-HB AGC-HB HBG A ,5

6 age 6 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.2 (0) GENERAL TEST REQUIREMENTS 1.2 (0.1) Information for luminaire design considered Standard Yes No 1.2 (0.3) More sections applicable... : Yes No 1.4 (2) CLASSIFICATION 1.4 (2.2) Type of protection... : Class I 1.4 (2.3) Degree of protection... : I (2.4) Luminaire suitable for direct mounting on normally flammable surfaces... : Yes No 1.4 (2.5) Luminaire for normal use... : Yes No Luminaire for rough service... : Yes No 1.5 (3) MARKING 1.5 (3.2) Mandatory markings osition of the marking On the enclosure Format of symbols/text See marking plate 1.5 (3.3) Additional information Language of instructions English language 1.5 (3.3.1) Combination luminaires 1.5 (3.3.2) Nominal frequency in Hz 50/60Hz 1.5 (3.3.3) Operating temperature 1.5 (3.3.4) Symbol or warning notice 1.5 (3.3.5) Wiring diagram Suitable for direct connection to the mains supply. See user s manual. 1.5 (3.3.6) Special conditions 1.5 (3.3.7) Metal halide lamp luminaire warning 1.5 (3.3.8) Limitation for semi-luminaires 1.5 (3.3.9) ower factor and supply current 1.5 (3.3.10) Suitability for use indoors Not only for indoors use. 1.5 (3.3.11) Luminaires with remote control 1.5 (3.3.12) Clip-mounted luminaire warning 1.5 (3.3.13) Specifications of protective shields 1.5 (3.3.14) Symbol for nature of supply ~

7 age 7 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.5 (3.3.15) Rated current of socket outlet 1.5 (3.3.16) Rough service luminaire Normal use luminaire 1.5 (3.3.17) Mounting instruction for type Y, type Z and some type X attachments Type Y 1.5 (3.3.18) Non-ordinary luminaires with VC cable 1.5 (3.3.19) rotective conductor current in instruction if applicable 1.5 (3.3.20) rovided with information if not intended to be mounted within arm s reach 1.5 (3.4) Test with water 15s Test with hexane 15s Legible after test Label attached 1.6 (4) CONSTRUCTION 1.6 (4.2) Components replaceable without difficulty 1.6 (4.3) Wireways smooth and free from sharp edges 1.6 (4.4) Lampholders 1.6 (4.4.1) Integral lampholder Integral LED module used 1.6 (4.4.2) Wiring connection 1.6 (4.4.3) Lampholder for end-to-end mounting 1.6 (4.4.4) ositioning - pressure test (N)... : After test the lampholder comply with relevant standard sheets and show no damage After test on single-capped lampholder the lampholder have not moved from its position and show no permanent deformation - bending test (N)... : After test the lampholder have not moved from its position and show no permanent deformation 1.6 (4.4.5) eak pulse voltage 1.6 (4.4.6) Centre contact 1.6 (4.4.7) arts in rough service luminaires resistant to tracking 1.6 (4.4.8) Lamp connectors 1.6 (4.4.9) Caps and bases correctly used

8 age 8 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.6 (4.5) Starter holders Starter holder in luminaires other than class II Starter holder class II construction 1.6 (4.6) Terminal blocks Tails Unsecured blocks 1.6 (4.7) Terminals and supply connections 1.6 (4.7.1) Contact to metal parts 1.6 (4.7.2) Test 8 mm live conductor Test 8 mm earth conductor 1.6 (4.7.3) Terminals for supply conductors Soldered connection. 1.6 ( ) Welded connections: - stranded or solid conductor - spot welding - welding between wires - Type Z attachment - mechanical test according to electrical test according to heat test according to and (4.7.4) Terminals other than supply connection Soldered connection. 1.6 (4.7.5) Heat-resistant wiring/sleeves 1.6 (4.7.6) Multi-pole plug - test at 30 N 1.6 (4.8) Switches: - adequate rating - adequate fixing - polarized supply - compliance with for electronic switches 1.6 (4.9) Insulating lining and sleeves 1.6 (4.9.1) Retainement Method of fixing... : Form a part of luminaire 1.6 (4.9.2) Insulated linings and sleeves Resistant to a temperature > 20 C to the wire temperature or

9 age 9 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict a) & c) Insulation resistance and electric strength b) Ageing test. Temperature (C)... : 1.6 (4.10) Insulation of Class II luminaires 1.6 (4.10.1) No contact, mounting surface accessible metal parts wiring of basic insulation Safe installation fixed luminaires Capacitors and switches Interference suppression capacitors according to IEC (4.10.2) Assembly gaps: - not coincidental - no straight access with test probe 1.6 (4.10.3) Retainment of insulation: - fixed - unable to be replaced; luminaire inoperative - sleeves retained in position - lining in lampholder 1.6 (4.11) Electrical connections 1.6 (4.11.1) Contact pressure Approved Class I independent LED driver used. 1.6 (4.11.2) Screws: - self-tapping screws - thread-cutting screws 1.6 (4.11.3) Screw locking: - spring washer - rivets 1.6 (4.11.4) Material of current-carrying parts 1.6 (4.11.5) No contact to wood or mounting surface 1.6 (4.11.6) Electro-mechanical contact systems 1.6 (4.12) Mechanical connections and glands 1.6 (4.12.1) Screws not made of soft metal Screws of insulating material Torque test: torque (Nm); part... : Screw for fixing the enclosure of driver: Ф=5,8mm, 2,5Nm Torque test: torque (Nm); part... :

10 age 10 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Torque test: torque (Nm); part... : 1.6 (4.12.2) Screws with diameter < 3 mm screwed into metal 1.6 (4.12.4) Locked connections: - fixed arms; torque (Nm)... : 5 Nm - lampholder; torque (Nm)... : - push-button switches; torque 0,8 Nm... : 1.6 (4.12.5) Screwed glands; force (Nm)... : Ф=11,7mm, 3,25Nm 1.6 (4.13) Mechanical strength 1.6 (4.13.1) Impact tests: - fragile parts; energy (Nm)... : - other parts; energy (Nm)... : 0,35 Nm for accessible parts 1) live parts 2) linings 3) protection 4) covers 1.6 (4.13.3) Straight test finger 1.6 (4.13.4) Rough service luminaires - I54 or higher a) fixed b) hand-held c) delivered with a stand d) for temporary installations and suitable for mounting on a stand 1.6 (4.13.6) Tumbling barrel 1.6 (4.14) Suspensions and adjusting devices 1.6 (4.14.1) Mechanical load: A) four times the weight Max. 7,7 Kg x 4=30,8 Kg for 1 hour. B) torque 2,5 Nm C) bracket arm; bending moment (Nm)... : D) load track-mounted luminaires E) clip-mounted luminaires, glass-shelve. Thickness (mm)... : Metal rod. diameter (mm)... :

11 age 11 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Fixed luminaire or independent control gear without fixing devices 1.6 (4.14.2) Load to flexible cables Mass (kg)... : Stress in conductors (N/mm²)... : Mass (kg) of semi-luminaire... : Bending moment (Nm) of semi-luminaire... : 1.6 (4.14.3) Adjusting devices: - flexing test; number of cycles... : - strands broken - electric strength test afterwards 1.6 (4.14.4) Telescopic tubes: cords not fixed to tube; no strain on conductors 1.6 (4.14.5) Guide pulleys 1.6 (4.14.6) Strain on socket-outlets 1.6 (4.15) Flammable materials: - glow-wire test 650 C LED cover. - spacing 30 mm - screen withstanding test of screen dimensions - no fiercely burning material - thermal protection - electronic circuits exempted 1.6 (4.15.2) Luminaires made of thermoplastic material with lamp control gear a) construction b) temperature sensing control c) surface temperature 1.6 (4.16) Luminaires for mounting on normally flammable surfaces No lamp control gear (compliance with Section 12) 1.6 (4.16.1) Lamp control gear spacing: - spacing 35 mm - spacing 10 mm 1.6 (4.16.2) Thermal protection: - in lamp control gear

12 age 12 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict - external - fixed position - temperature marked lamp control gear 1.6 (4.16.3) Design to satisfy the test of 12.6 (see 12.6) 1.6 (4.17) Drain holes Clearance at least 5 mm 1.6 (4.18) Resistance to corrosion: 1.6 (4.18.1) - rust-resistance 1.6 (4.18.2) - season cracking in copper 1.6 (4.18.3) - corrosion of aluminium 1.6 (4.19) Ignitors compatible with ballast 1.6 (4.20) Rough service vibration 1.6 (4.21) rotective shield: 1.6 (4.21.1) Shield fitted Shield of glass if tungsten halogen lamps 1.6 (4.21.2) articles from a shattering lamp not impair safety 1.6 (4.21.3) No direct path 1.6 (4.21.4) Impact test on shield Glow-wire test on lamp compartment 1.6 (4.22) Attachments to lamps 1.6 (4.23) Semi-luminaires comply Class II 1.6 (4.24) UV radiation for tungsten halogen lamps and metal halide lamps (Annex ) 1.6 (4.25) No sharp point or edges 1.6 (4.26) Short-circuit protection: 1.6 (4.26.1) Uninsulated accessible SELV parts 1.6 (4.26.2) Short-circuit test 1.6 (4.26.3) Test chain according to Figure (4.27) Terminal blocks with integrated screwless earthing contacts tested according Annex V ull test of terminal fixing (20 N) After test, resistance < 0,05 ull test of mechanical connection (50 N) After test, resistance < 0,05

13 age 13 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Voltage drop test, resistance < 0, (11) CREEAGE DISTANCES AND CLEARANCES Working voltage (V)... : V~ Voltage form Sinusoidal Non-sinusoidal TI < 600 > 600 Impulse withstand category (Normal category II) (Category III Annex U) Category II Category III Rated pulse voltage (kv)... : -- (1) Current-carrying parts of different polarity: cr (mm); cl (mm)... : (2) Current-carrying parts and accessible parts: cr (mm); cl (mm)... : For all models, use approved independent LED driver. For all models, use approved independent LED driver. Between output circuit and accessible parts: Cl.: 1,3>0,2mm Cl.: 1,3>1,2mm (3) arts becoming live due to breakdown of basic insulation and metal parts: cr (mm); cl (mm)... : (4) Outer surface of cable where it is clamped and metal parts: cr (mm); cl (mm)... : (6) Current-carrying parts and supporting surface: cr (mm); cl (mm)... : For all models, use approved independent LED driver. Between output circuit and accessible parts: Cl.: 1,3>0,2mm Cl.: 1,3>1,2mm 1.8 (7) ROVISION FOR EARTHING 1.8 ( ) Accessible metal parts Metal parts in contact with supporting surface Approved Class I independent LED driver used. Resistance < 0,5... : For model AGC-HB01-150: Max. 0,011 For model AGC-HB01-200: Max. 0,013 Self-tapping screws used Thread-forming screws

14 age 14 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.8 ( ) Thread-forming screw used in a grove Earth makes contact first Terminal blocks with integrated screwless earthing contacts tested according Annex V Earth continuity in joints etc. 1.8 (7.2.4) Locking of clamping means Compliance with Terminal blocks with integrated screwless earthing contacts tested according Annex V 1.8 (7.2.5) Earth terminal integral part of connector socket 1.8 (7.2.6) Earth terminal adjacent to mains terminals 1.8 (7.2.7) Electrolytic corrosion of the earth terminal Ordinary luminaire 1.8 (7.2.8) Material of earth terminal Contact surface bare metal 1.8 (7.2.10) Class II luminaire for looping-in Double or reinforced insulation to functional earth 1.8 (7.2.11) Earthing core coloured green-yellow Length of earth conductor 1.9 (14) SCREW TERMINALS Separately approved; component list art of the luminaire (see Annex 3) 1.9 (15) SCREWLESS TERMINALS AND ELECTRICAL CONNECTIONS Separately approved; component list (see Annex 1) art of the luminaire Soldered connection (5) EXTERNAL AND INTERNAL WIRING 1.10 (5.2) Supply connection and external wiring 1.10 (5.2.1) Means of connection... : Supply cord 1.10 (5.2.2) Type of cable... : H05RN-F Nominal cross-sectional area (mm²)... : 3 x 1,0 mm² Cables equal to IEC or IEC (5.2.3) Type of attachment, X, Y or Z Type Y

15 age 15 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.10 (5.2.5) Type Z not connected to screws 1.10 (5.2.6) Cable entries: - suitable for introduction - adequate degree of protection 1.10 (5.2.7) Cable entries through rigid material have rounded edges 1.10 (5.2.8) Insulating bushings: - suitably fixed - material in bushings - material not likely to deteriorate - tubes or guards made of insulating material 1.10 (5.2.9) Locking of screwed bushings 1.10 (5.2.10) Cord anchorage: 1.10 ( ) 1.10 ( ) 1.10 ( ) - covering protected from abrasion - clear how to be effective - no mechanical or thermal stress - no tying of cables into knots etc. - insulating material or lining Cord anchorage for type X attachment: a) at least one part fixed b) types of cable c) no damaging of the cable d) whole cable can be mounted e) no touching of clamping screws f) metal screw not directly on cable g) replacement without special tool Glands not used as anchorage Labyrinth type anchorages Adequate cord anchorage for type Y and type Z attachment Tests: Type Y - impossible to push cable; unsafe - pull test: 25 times; pull (N)... : 60N

16 age 16 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict - torque test: torque (Nm)... : 0,25 Nm - displacement 2 mm 0,39 mm - no movement of conductors - no damage of cable or cord 1.10 (5.2.11) External wiring passing into luminaire 1.10 (5.2.12) Looping-in terminals 1.10 (5.2.13) Wire ends not tinned Wire ends tinned: no cold flow 1.10 (5.2.14) Mains plug same protection Class III luminaire plug 1.10 (5.2.16) Appliance inlets (IEC 60320) Appliance couplers of class II type 1.10 (5.2.17) No standardized interconnecting cables properly assembled 1.10 (5.2.18) Used plug in accordance with - IEC other standard 1.10 (5.3) Internal wiring 1.10 (5.3.1) Internal wiring of suitable size and type Through wiring - not delivered/ mounting instruction - factory assembled - socket outlet loaded (A)... : - temperatures... : (see Annex 2) Green-yellow for earth only 1.10 ( ) Internal wiring connected directly to fixed wiring Cross-sectional area (mm²)... : Insulation thickness Extra insulation added where necessary 1.10 ( ) Internal wiring connected to fixed wiring via internal current-limiting device Adequate cross-sectional area and insulation thickness 1.10 ( ) Double or reinforced insulation for class II 1.10 ( ) Conductors without insulation

17 age 17 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.10 ( ) SELV current-carrying parts 1.10 ( ) Insulation thickness other than VC or rubber 1.10 (5.3.2) Sharp edges etc. There is no sharp edges can damage the internal wiring. No moving parts of switches etc. Joints, raising/lowering devices Telescopic tubes etc. No twisting over (5.3.3) Insulating bushings: - suitable fixed - material in bushings - material not likely to deteriorate - cables with protective sheath 1.10 (5.3.4) Joints and junctions effectively insulated 1.10 (5.3.5) Strain on internal wiring 1.10 (5.3.6) Wire carriers 1.10 (5.3.7) Wire ends not tinned Wire ends tinned: no cold flow 1.11 (8) ROTECTION AGAINST ELECTRIC SHOCK 1.11 (8.2.1) Live parts not accessible Basic insulated parts not used on the outer surface without appropriate protection Basic insulated parts not accessible with standard test finger on portable and adjustable luminaires Basic insulated parts not accessible with Ø 50 mm probe from outside, within arm s reach, on wall-mounted luminaires Lamp and starterholders in portable and adjustable luminaires comply with double or reinforced insulation requirements Basic insulation only accessible under lamp or starter replacement rotection in any position Double-ended tungsten filament lamp Insulation lacquer not reliable Double-ended high pressure discharge lamp

18 age 18 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Relevant warning according to fitted to the luminaire 1.11 (8.2.2) ortable luminaire adjusted in most unfavourable position 1.11 (8.2.3.a) Class II luminaire: - basic insulated metal parts not accessible during starter or lamp replacement - basic insulation not accessible other than during starter or lamp replacement - glass protective shields not used as supplementary insulation 1.11 (8.2.3.b) BC lampholder of metal in class I luminaires shall be earthed 1.11 (8.2.3.c) Class III luminaires with exposed SELV parts: Ordinary luminaire: - touch current... : - no-load voltage... : Other than ordinary luminaire: - nominal voltage... : 1.11 (8.2.4) ortable luminaire have protection independent of supporting surface 1.11 (8.2.5) Compliance with the standard test finger or relevant probe 1.11 (8.2.6) Covers reliably secured 1.11 (8.2.7) Discharging of capacitors 0,5 F Approved independent SELV LED driver used. ortable plug connected luminaire with capacitor Other plug connected luminaire with capacitor Discharge device on or within capacitor Discharge device mounted separately 1.12 (12) ENDURANCE TEST AND THERMAL TEST 1.12 (-) If I > I 20 relevant test of (12.4), (12.5) and (12.6) after (9.2) before (9.3) specified in (12.3) Endurance test: - mounting-position... : On the black testing ceiling - test temperature (C)... : 60C

19 age 19 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict - total duration (h)... : 240h - supply voltage: Un factor; calculated voltage (V) : 264 V - lamp used... : Integral LED 1.12 (12.3.2) After endurance test: - no part unserviceable - luminaire not unsafe - no damage to track system - marking legible - no cracks, deformation etc (12.4) Thermal test (normal operation) (see Annex 2) 1.12 (12.5) Thermal test (abnormal operation) (see Annex 2) 1.12 (12.6) Thermal test (failed lamp control gear condition): 1.12 (12.6.1) Through wiring or looping-in wiring loaded by a current of (A)... : -- - case of abnormal conditions... : -- - electronic lamp control gear - measured winding temperature (C): at 1,1 Un. : -- - measured mounting surface temperature (C) at 1,1 Un... : -- - calculated mounting surface temperature (C).. : -- - track-mounted luminaires 1.12 (12.6.2) Temperature sensing control - case of abnormal conditions... : -- - thermal link - manual reset cut-out - auto reset cut-out - measured mounting surface temperature (C)... : -- - track-mounted luminaires 1.12 (12.7) Thermal test (failed lamp control gear in plastic luminaires): 1.12 (12.7.1) Luminaire without temperature sensing control 1.12 ( ) Luminaire with fluorescent lamp 70W Test method or Annex W... : -- Test according to :

20 age 20 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict - case of abnormal conditions - Ballast failure at supply voltage (V)... : -- - Components retained in place after the test - Test with standard test finger after the test Test according to Annex V: - case of abnormal conditions - measured winding temperature (C): at 1,1 Un.. : ( ) - measured temperature of fixing point/exposed part (C): at 1,1 Un... : - calculated temperature of fixing point/exposed part (C)... : Ball-pressure test: part tested; temperature (C)... : -- - part tested; temperature (C)... : -- Luminaire with discharge lamp, fluorescent lamp > 70W, transformer > 10 VA - case of abnormal conditions 1.12 ( ) - measured winding temperature (C): at 1,1 Un.. : -- - measured temperature of fixing point/exposed part (C): at 1,1 Un... : - calculated temperature of fixing point/exposed part (C)... : Ball-pressure test: part tested; temperature (C)... : -- - part tested; temperature (C)... : -- Luminaire with short circuit proof transformers 10 VA - case of abnormal conditions - Components retained in place after the test - Test with standard test finger after the test 1.12 (12.7.2) Luminaire with temperature sensing control - thermal link Yes No - manual reset cut-out Yes No - auto reset cut-out Yes No - case of abnormal conditions

21 age 21 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict - highest measured temperature of fixing point/exposed part (C):... : Ball-pressure test: -- - part tested; temperature (C)... : -- - part tested; temperature (C)... : (9) RESISTANCE TO DUST, SOLID OBJECTS AND MOISTURE 1.13 (-) If I > I 20 the order of the test specified in clause (9.2) Tests for ingress of dust, solid objects and moisture: - classification according to I... : I65 - mounting position during test... : According to the user s manual. - fixing screws tightened; torque (Nm)... : -- - tests according to clauses... : Cl and Cl electric strength test afterwards a) no deposit in dust-proof luminaire b) no talcum in dust-tight luminaire c) no trace of water on current-carrying parts or SELV parts or where it could become a hazard d) i) For luminaires without drain holes no water entry d) ii) For luminaires with drain holes no hazardous water entry e) no water in watertight luminaire f) no contact with live parts (I 2X) f) no entry into enclosure (I 3X and I 4X) f) no contact with live parts (I3X and I4X) g) no trace of water on part of lamp requiring protection from splashing water h) no damage of protective shield or glass envelope 1.13 (9.3) Humidity test 48 h 25C, 93%R.H. for 48 h 1.14 (10) INSULATION RESISTANCE AND ELECTRIC STRENGTH 1.14 (10.2.1) Insulation resistance test Cable or cord covered by metal foil or replaced by a metal rod of mm Ø... : --

22 age 22 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Insulation resistance (M) SELV: - between current-carrying parts of different polarity... : - between current-carrying parts and mounting surface... : - between current-carrying parts and metal parts of the luminaire... : - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts... : For model AGC-HB01-150: 7, M > 1 M For model AGC-HB01-200: 3, M > 1 M For model AGC-HB01-150: 7, M > 1 M For model AGC-HB01-200: 3, M > 1 M - Insulation bushings as described in Section 5.. : Other than SELV: - between live parts of different polarity... : Approved independent SELV LED driver used. - between live parts and mounting surface... : For model AGC-HB01-150: 1, M > 2 M For model AGC-HB01-200: 8, M > 2 M - between live parts and metal parts... : For model AGC-HB01-150: 1, M > 2 M For model AGC-HB01-200: 3, M > 2 M - between live parts of different polarity through action of a switch... : - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts... : - Insulation bushings as described in Section 5.. : 1.14 (10.2.2) Electric strength test Dummy lamp Luminaires with ignitors after 24 h test Luminaires with manual ignitors Test voltage (V): SELV: - between current-carrying parts of different polarity... : -----

23 age 23 of 50 Report No.: IEC Clause Requirement + Test Result - Remark Verdict - between current-carrying parts and mounting surface... : - between current-carrying parts and metal parts of the luminaire... : - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts... : 500 V for 1 min. 500 V for 1 min. - Insulation bushings as described in Section 5.. : Other than SELV: - between live parts of different polarity... : Approved independent SELV LED driver used. - between live parts and mounting surface... : 1480 V for 1 min. - between live parts and metal parts... : 1480 V for 1 min. - between live parts of different polarity through action of a switch... : - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts... : Insulation bushings as described in Section 5.. : (10.3) Touch current or protective conductor current (ma)... : Touch current: max. 0,045mA (limit: 0,7mA) protective conductor current: Max 0,097mA (limit: 3,5mA) 1.15 (13) RESISTANCE TO HEAT, FIRE AND TRACKING 1.15 (13.2.1) Ball-pressure test: - part tested; temperature (C)... : - part tested; temperature (C)... : 1.15 (13.3.1) Needle flame test (10 s): - part tested... : - part tested... : 1.15 (13.3.2) Glow-wire test (650C): - part tested... : LED cover. - part tested... : 1.15 (13.4.1) Tracking test: - part tested... : - part tested... :

24 age 24 of 50 Report No.: ANNEX 1: components object/part No. ower cord for EU market code manufacturer/ trademark B Dong Guan Recheer Electric Wire & Cable Co., Ltd. (Alternative) D Zhejiang Jinniu Cable Co., Ltd ower cord for Australia market B Dong Guan Recheer Electric Wire & Cable Co Ltd LEDs C NICHIA CORORATION LED CB Rubber gasket for waterproof LED driver (AGC- HB01-100, AGC- HB01-120, AGC- HB01-150) LED driver (AGC-HB01-200) B, C XIANYANG HONGDA ELECTRONIC MATERIAL CO LTD B, C JIANGSU HONGDA NEW MATERIAL CO LTD B B Mean Well Enterprises Co., Ltd Mean Well Enterprises Co., Ltd type/model technical data standard mark(s) of conformity H05RN-F 3x1,0mm 2 300V/500V H05RN-F 3x1,0mm 2 300V/500V H05RN-F 3x1,0mm 2 NF2W757D RT-V1 HDMA HD-95 HBG A HBG A 300V/500V Vf: 6,4 V, If: 150 ma, White light 130 C, V-0, Thickness: 1,5mm Silicon rubber, 150 C Independent SELV, Input: AC V, 1,7A, 50/60Hz Output: 48Vdc, Max 3,3A, Ta: 50 C, Tc: 85 C Input: AC V, 2,5A, 50/60Hz Output: 49Vdc, Max 5,0A, SELV, Ta: 50 C, Tc: 75 C -- VDE VDE NSW VDE UL E UL E IEC A1 IEC EN A1 EN JTUV ENEC NO 3473 The codes above have the following meaning: A - The component is replaceable with another one, also certified, with equivalent characteristics B - The component is replaceable if authorised by the test house C - Integrated component tested together with the appliance D - Alternative component

25 age 25 of 50 Report No.: ANNEX 2: temperature measurements, thermal tests of Section Type reference... : AGC-HB Lamp used... : With integrated LED Lamp control gear used... : HBG A Mounting position of luminaire... : According to instruction from manufacturer Supply wattage (W)... : 150,6W Supply current (A)... : 0,614A Calculated power factor... : Table: measured temperatures corrected for ta = 50C: - abnormal operating mode... : -- - test 1: rated voltage... : - test 2: 1,06 times rated voltage or 1,05 times rated wattage... : - test 3: Load on wiring to socket-outlet, 1,06 times voltage or 1,05 times wattage... : - test 4: 1,1 times rated voltage or 1,05 times rated wattage... : Through wiring or looping-in wiring loaded by a current of A during the test... : 1,06 240=254,4V U=264 Vac Approved independent SELV LED driver use. Short circuit output: shut down temperature (C) of part Clause 12.4 normal Clause 12.5 abnormal test 1 test 2 test 3 limit test 4 limit ower cord -- 56, Tc of driver -- 65, Ambient temperature of LED driver -- 45, Output wire of driver -- 68, CB of LED module -- 68, Metal case -- 58,2 -- Ref LED cover (glass) -- 58,4 -- Ref Objects lighted (0,1m) -- 62, Mounting surface -- 61,

26 age 26 of 50 Report No.: ANNEX 2: temperature measurements, thermal tests of Section 12 Type reference... : AGC-HB Lamp used... : With integrated LED Lamp control gear used... : HBG A Mounting position of luminaire... : According to instruction from manufacturer Supply wattage (W)... : 194,7W Supply current (A)... : 0,799A Calculated power factor... : Table: measured temperatures corrected for ta = 50C: - abnormal operating mode... : -- - test 1: rated voltage... : - test 2: 1,06 times rated voltage or 1,05 times rated wattage... : - test 3: Load on wiring to socket-outlet, 1,06 times voltage or 1,05 times wattage... : - test 4: 1,1 times rated voltage or 1,05 times rated wattage... : Through wiring or looping-in wiring loaded by a current of A during the test... : 1,06 240=254,4V U=264 Vac Approved independent SELV LED driver use. Short circuit output: shut down temperature (C) of part Clause 12.4 normal Clause 12.5 abnormal test 1 test 2 test 3 limit test 4 limit ower cord -- 58, Tc of driver -- 68, Ambient temperature of LED driver -- 47, Output wire of driver -- 77, CB of LED module -- 77, Metal case -- 63,3 -- Ref LED cover (glass) -- 67,4 -- Ref Objects lighted (0,1m) -- 77, Mounting surface -- 64,

27 age 27 of 50 Report No.: ANNEX 3: screw terminals (part of the luminaire) (14) SCREW TERMINALS (14.2) Type of terminal...: Rated current (A)...: ( ) One or more conductors ( ) Special preparation ( ) Terminal size Cross-sectional area (mm²)...: (14.3.3) Conductor space (mm)...: (14.4) Mechanical tests (14.4.1) Minimum distance (14.4.2) Cannot slip out (14.4.3) Special preparation (14.4.4) Nominal diameter of thread (metric ISO thread)..: M External wiring No soft metal (14.4.5) Corrosion (14.4.6) Nominal diameter of thread (mm)...: Torque (Nm)...: (14.4.7) Between metal surfaces Lug terminal Mantle terminal ull test; pull (N)...: (14.4.8) Without undue damage

28 age 28 of 50 Report No.: ANNEX 4: screwless terminals (part of the luminaire) (15) SCREWLESS TERMINALS (15.2) Type of terminal... : Rated current (A)... : (15.3.1) Material (15.3.2) Clamping (15.3.3) Stop (15.3.4) Unprepared conductors (15.3.5) ressure on insulating material (15.3.6) Clear connection method (15.3.7) Clamping independently (15.3.8) Fixed in position ( ) Conductor size Type of conductor (15.5.1) Terminals internal wiring ( ) ull test spring-type terminals (4 N, 4 samples).: ( ) ull test pin or tab terminals (4 N, 4 samples) : Insertion force not exceeding 50 N (15.5.2) ermanent connections: pull-off test (20 N) (15.6) Electrical tests Voltage drop (mv) after 1 h (4 samples)... : Voltage drop of two inseparable joints Number of cycles... : Voltage drop (mv) after 10th alt. 25th cycle (4 samples)... : Voltage drop (mv) after 50th alt. 100th cycle (4 samples)... : After ageing, voltage drop (mv) after 10th alt. 25th cycle (4 samples)... : After ageing, voltage drop (mv) after 50th alt. 100th cycle (4 samples)... : (15.7) Terminals external wiring Terminal size and rating (15.8.1) ull test spring-type terminals or welded connections (4 samples); pull (N)... :

29 ull test pin or tab terminals (4 samples); pull (N)... : age 29 of 50 Report No.: (15.9) Contact resistance test Voltage drop (mv) after 1 h terminal voltage drop (mv) Voltage drop of two inseparable joints Voltage drop after 10th alt. 25th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Continued ageing: voltage drop after 10th alt. 25th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Continued ageing: voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv)

30 age 30 of 50 Report No.: Annex 5: EUROEAN GROU DIFFERENCES AND NATIONAL DIFFERENCES Luminaires art 2: articular requirements: Section One Fixed general purpose luminaires Differences according... : EN :1989 used in conjunction with EN : A11:2009 Annex Form No.... : EU_GD_IEC_60598_2_1B Annex Form Originator... : IMQ S.p.A. Master Annex Form... : Copyright 2009 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. CENELEC COMMON MODIFICATIONS (EN) 1.5 (3) MARKING 1.5 ( ) Adequate warning on the package 1.6 (4) CONSTRUCTION 1.6 (4.11.6) Electro-mechanical contact systems 1.10 (5) EXTERNAL AND INTERNAL WIRING 1.10 (5.2.1) Connecting leads - without a means for connection to the supply - terminal block specified - relevant information provided - compliance with 4.6, 4.7.1, 4.7.2, , 11.2, 12 and 13.2 of art (5.2.2) Cables equal to HD21 S2 or HD22 S (12) ENDURANCE TEST AND THERMAL TEST 1.12 (12.4.2c) Thermal test (normal operation) ZB ANNEX ZB, SECIAL NATIONAL CONDITIONS (EN) (3.3) DK: power supply cord with label IT: warning label on Class 0 luminaire (4.5.1) DK: socket-outlets (5.2.1) CY, DK, FI, SE, GB: type of plug

31 age 31 of 50 Report No.: Annex 5: EUROEAN GROU DIFFERENCES AND NATIONAL DIFFERENCES ZC ANNEX ZC, NATIONAL DEVIATIONS (EN) (4 & 5) FR: Shuttered socket-outlets 10/16A (13.3) (13.3) FR: Glow-wire test 850C alt. 750C for luminaires in premises open to public or 960 C for luminaires in emergency exits GB: Requirements according to United Kingdom Building Regulation

32 age 32 of 50 Report No.: Annex 6 LED modules for general lighting Safety specifications IEC/EN 62031:2008 Clause Requirement Test Result - Remark Verdict 13 Fault conditions 13.1 General The module shall not impair safety when operated under fault conditions that may occur during the intended use. The requirements of IEC , Clause 14, apply. Additionally, the following test shall be carried out. art Simulated fault 13.2 Overpower condition: 1. Adjusted until 150% of the rated voltage, current or power is reached. 2. The test continued until the module is thermally stable. Test result: the lamp operated as usual, no hazard.

33 age 33 of 50 Report No.: Annex 7 Variations to IEC :2008 for application in Australia and/or New Zealand (AS/NZS :2013) Verdict Clause Requirement Test Result - Remark Verdict ZZ1 Variations made to IEC :2008 are incorporated in the body of this Standard. They are listed in this Annex for easy reference. ZZ2 Variations In Australia the supply voltage is 230V/400V and for testing the rated voltage is 240V/415V. : Rated voltage: V; Rated test voltage: 240 V 2.2 Class 0 luminaires not allowed in Australia; type of protection. : 3.1 Move Item from the centre column to the right hand column In Australia and New Zealand, instructions and other texts required by this Standard shall be written in English. Compliance is checked by inspection Luminaires for use with metal halide lamps shall be provided with instructions that state the substance of the following: To avoid potential unsafe lamp failure, the luminaire shall be switched off for at least 30 minutes at least once a week. In addition, the luminaire shall be operated: complete with its protective shield; or with a double jacketed lamp. In English Delete Clause The instructions shall contain details related to components in the luminaire that require replacement as part of a maintenance program. 4.8 Add the following paragraph after the third paragraph: Switches that indicate an off position shall have contacts with an air break and comply with AS/NZS 3133 or AS/NZS

34 age 34 of 50 Report No.: Annex 7 Variations to IEC :2008 for application in Australia and/or New Zealand (AS/NZS :2013) Verdict Clause Requirement Test Result - Remark Verdict 4.2A 4.2A Capacitors shall be of a type to ensure that any capacitor failure results in a failsafe outcome (i.e. the capacitor type will fail in the open-circuit mode only and is protected against fire or shock hazard). Capacitors shall be not less than Type B capacitors with metal body and break action protection in accordance with IEC and IEC A capacitor complying with ANCI/EIA- 456-A shall comply with IEC and IEC 61048:2006 excluding the endurance test of NOTE Capacitors of Class S2 (formerly referred to as 2) of IEC (all parts) do not meet the safety requirements of a Type B capacitor. In addition, capacitors shall have a minimum voltage rating of 250 V at a temperature rating of 100 C or 280 V at a temperature rating of 85 C. Capacitors likely to be permanently subjected to the supply voltage, and used for radio interference suppression or for voltage dividing, shall comply with IEC Delete the first paragraph and replace with the following: Luminaires shall be provided with only one of the following means of connection and isolation to the supply. Fixed luminaires: device for the connection of luminaires; terminals; plug for engagement with socketoutlets; connecting lead (tails); supply cord and plug; adapter for engagement with supply tracks; appliance inlet; installation coupler; luminaire coupler; ortable luminaires: supply cord with plug; appliance inlet. Track-mounted luminaires: adaptor; connector. Delete the second and third paragraph.

35 Annex 7 age 35 of 50 Report No.: Variations to IEC :2008 for application in Australia and/or New Zealand (AS/NZS :2013) Verdict Clause Requirement Test Result - Remark Verdict Delete the first paragraph and replace with the following: Supply cords used as a means of connection to the supply, when supplied by the luminaire manufacturer, shall be at least equal in their mechanical and electrical properties to those specified in IEC and IEC 60245, as indicated in Table 5.1, or AS/NZS 3191, and shall be capable of withstanding, without deterioration, the highest temperature to which they may be exposed under normal conditions of use. 2 Table 5.1, delete rows 4 and 5 and replace with the following: Luminaires which are other than ordinary ortable rough service luminaires IEC IEC 53 ortable rough service luminaires IEC 66 VC insulated and sheathed heavy duty flexible cord 3. Delete the third paragraph and replace with the following: To provide adequate mechanical strength, the nominal cross-sectional area of the conductors shall be not less than: 0,75 mm 2 ; 1,0 mm 2 for portable rough service luminaires Add the following text at the end of Clause : Class II luminaires for fixed wiring incorporating an appliance coupler shall not have means to allow further luminaires to be connected, including looping in by cascading. Luminaire couplers incorporated with the luminaire shall comply with IEC Delete Clause and replace with the following:

36 age 36 of 50 Report No.: Annex 7 Variations to IEC :2008 for application in Australia and/or New Zealand (AS/NZS :2013) Verdict Clause Requirement Test Result - Remark Verdict All portable luminaires with a flexible supply cord shall be fitted with a plug complying with AS/NZS Other luminaires with flexible cords shall be fitted with a plug complying with AS/NZS 3112, unless they have the warning allowed by Clause Add the following new Clause: Installation couplers incorporated within luminaires shall comply with the requirements of AS/NZS Luminaires incorporating installation couplers may have means to allow further luminaires to be connected by cascading provided the through wiring is rated for the current rating of the installation coupler Delete the third paragraph and replace with the following: Internal wires coloured green, yellow or green/yellow combination shall be used for making protective earth connections only. Functional earth connections shall not be made by wires coloured green, yellow or green/yellow combination. Add the following new Note: NOTE 3 Internal wires of other colours are not precluded from making protective earthing connections Delete the third paragraph and replace with the following: All conductors, whether internal or external, coloured green, yellow or green/yellow combination, shall only be connected to an earthing terminal Delete the first paragraph and Note 1 and replace with the following:

37 age 37 of 50 Report No.: Annex 7 Variations to IEC :2008 for application in Australia and/or New Zealand (AS/NZS :2013) Verdict Clause Requirement Test Result - Remark Verdict Luminaires shall be so constructed that their live parts and basic insulation are not accessible when the luminaire has been installed and wired as in normal use. Live parts shall not be accessible when the luminaire is opened as necessary for replacing lamps, replaceable light sources or (replaceable) starters, even if the operation cannot be achieved by hand. NOTE Examples of parts with basic insulation are cables intended for internal wiring, controlgear for building-in etc. This does not apply to the non-current -carrying parts of caps which comply with the relevant IEC safety standard. Where a protective cover is used over a non-userreplaceable light source to provide protection against electric shock, and the cover is marked with the caution, electric shock risk symbol in accordance with IEC , the cover shall be left in place during the tests and inspections detailed by Section 8 of this Standard. The cover shall be held securely in position by fixings requiring the use of a tool for their removal, and at least two independent fixings shall be used. TABLE 12.1 Add the following new Note after Table 12.1: CLAUSE 13.3 NOTE Luminaire manufacturers should consider the maximum ambient air temperature in the vicinity of components such as starting devices and electronic ballasts or converters. Component performance specifications advise manufacturers to mark or supply life data as maximum ambient air temperature based on 50,000 hrs. This t-life is often marked as ta and is the temperature of the air in the vicinity of the component and is not related to the luminaire ta. As such, luminaire manufacturers should measure air temperature in the vicinity of such components, within the luminaire, as even those complying with their tc point measurements can still fail prematurely if t- life is exceeded. Delete Clause 13.3 and replace with the following: 13.3 Resistance to flame and ignition arts of non-metallic material shall be resistant to flame and ignition. For materials other than ceramic, compliance is Glow-wire test (750C): Bobbin of transformer and line chock, CB of driver: No flame, no drop. Glow-wire test (650C):

38 age 38 of 50 Report No.: Annex 7 Variations to IEC :2008 for application in Australia and/or New Zealand (AS/NZS :2013) Verdict Clause Requirement Test Result - Remark Verdict checked by the tests of and , and , as appropriate. This requirement does not apply to decorative trims, knobs, wiring insulation and other parts not likely to be ignited or to propagate flames from inside the luminaire. This Clause applies to all parts, including components, even if they have been tested to their own standard arts of non-metallic material supporting connections shall withstand the following test: arts are subject to a test using a nickel-chromium glow-wire. The test apparatus and test procedure shall be those described in AS/NZS The glow wire is heated to 750 C and applied to the test sample for 30 s. For all tests, any flame or glowing of the sample shall extinguish within 30 s of withdrawing the glow-wire, and any burning or molten drop shall not ignite a single layer of tissue paper specified in of ISO :2002, spread out horizontally 200 mm ± 5 mm below the sample All other parts of non-metallic material shall withstand the following test: arts are subject to a test using a nickel-chromium glow-wire. The test apparatus and test procedure shall be those described in AS/NZS The glow wire is heated to 650 C and applied to the test sample for 30 s. For all tests, any flame or glowing of the sample shall extinguish within 30 s of withdrawing the glow-wire, and any burning or molten drop shall not ignite a single layer of tissue paper specified in of ISO :2002, spread out horizontally 200 mm ± 5 mm below the sample During the application of the 750 C glow wire test of Clause , if a flame is produced that persists for longer than 2 s, the luminaire is further tested as follows: The needle-flame test of AS/NZS is applied to non-metallic parts that encroach within the envelope of a vertical cylinder having a diameter of 20 mm and a height of 50 mm above the point of application of the glow wire. The needle flame is applied to the test sample for 30 s. arts shielded by a barrier that meets the needle- lastic cover: no flame, no drop.

39 Annex 7 age 39 of 50 Report No.: Variations to IEC :2008 for application in Australia and/or New Zealand (AS/NZS :2013) Verdict Clause Requirement Test Result - Remark Verdict flame test of AS/NZS are not tested. NOTE This requires the needle flame to be applied to all parts likely to be impinged upon by the glow-wire flame within the hypothetical envelope of a vertical cylinder positioned above the point of application of the glow-wire. This applies to all parts unless there is a barrier that passes the needle-flame test and is within the cylinder and would protect the part from the glowwire flame. The duration of burning shall not exceed 30 s after removal of the test flame and any burning drop shall not ignite the underlying parts or tissue paper specified in of ISO :2002, spread out horizontally 200 mm ± 5 mm below the sample. The needle-flame test is not carried out on parts that are made of material classified as V-0 or V-1 according to AS/NZS The sample of material classified in accordance with AS/NZS shall be no thicker than the relevant part CBs in luminaires shall be subject to the needle-flame test of AS/NZS The needle flame shall be applied for 30 seconds to an edge of the CB at least 10 mm from a corner. The duration of burning shall not exceed 15 s after removal of the needle flame and any burning droplets shall not ignite the tissue paper placed underneath the CB. The needle-flame test is not carried out on CBs made of material that is V-0 rated according to AS/NZS Bibliography Add the following reference: AS/NZS , Household and similar electrical appliances Safety, art 1: General requirements (IEC Ed 5, MOD) IEC 60252, AC motor capacitors (all parts)

40 age 40 of 50 Report No.: Annex 8 Variations to AS/NZS :1998 for application in Australia and/or New Zealand (AS/NZS :2014) Clause Requirement + Test Result - Remark Verdict 6 MARKING LED luminaires with G5 or G13 lampholders shall be marked with the following warning: WARNING: NOT FOR USE WITH ANY FLUORESCENT LAM FOR USE ONLY WITH TYE A or TYE B LED LAMS The warning label shall be durable and the font size shall be a minimum of 5 mm for letters and numbers and 5 mm for symbols and shall be visible during lamp replacement. 7 CONSTRUCTION LED luminaires with G5 and G13 lampholders shall include a fuse to protect a fluorescent lamp that is inadvertently installed: Fuse shall a) be of the 250 V HRC type; b) have a 0.5 A max. quick-acting type rating; and c) be used to protect a maximum of two lamps. AENDIX A SAFETY REQUIREMENTS FOR DOUBLE-CAED LED LAMS A4 CLASSIFICATION A4.1 Type of protection:... : Class II Class III A4.1 A class III lamp shall have class II construction and comply with all of the requirements for protection against electric shock for a class II lamp at a nominal rating of 240 V a.c. A4.2 Type of lamps Type A Type B A4.2 Type B lamps will no longer be permitted after May 16, ermitted Not ermitted A5 MARKING A5.2 Mandatory markings - mark of origin - rated supply voltage (V)... : - rated wattage (W)... : - rated frequency (Hz)... : - value of tc... : - tc point... : - model number... : - I rating if greater than I20... :

41 age 41 of 50 Report No.: Annex 8 Variations to AS/NZS :1998 for application in Australia and/or New Zealand (AS/NZS :2014) Clause Requirement + Test Result - Remark Verdict - markings to identify the line and neutral supply connections of lampholder... : - The lamp type shall be marked with the text Type A or Type B, as per the appropriate subfigure of Figure A1 A5.3 Warning label shall be supplied with the lamp: WARNING: NOT FOR USE WITH ANY FLUORESCENT LAM FOR USE ONLY WITH TYE A or TYE B LED LAMS The warning label shall be durable and the font size shall be a minimum of 5 mm for letters and numbers and 5 mm for symbols and shall be visible during lamp replacement. A5.4 Marking of associated components The component to replace the starter shall be marked as shown in Figure A2... : osition of the marking Format of symbols/text Additional information Language of instructions A6 INSTRUCTIONS A6.1 Information to be supplied with the lamp -Special conditions or restrictions to be observed for lamp operation. - Not suitable for dimming; symbol used - wiring diagram for lamp installation - Information on the specification and compatibility of control gear with which the lamp can be used. - the ambient operation temperature range of the lamp if other than 10 to 30C - Information of the type of lamp it replace including lamp length, lamp cap configuration and I rating. A6.2 Information to be supplied for emergency luminaire A6.3 Information about additional components A6.4 Warnings: The instructions for lamps intended for use in an existing luminaire that requires modification other than replacement of the lamp or starter shall include the following warnings:

42 age 42 of 50 Report No.: Annex 8 Variations to AS/NZS :1998 for application in Australia and/or New Zealand (AS/NZS :2014) Clause Requirement + Test Result - Remark Verdict Warnings: The instructions for lamps intended for use in a new luminaire A6.5 Additional information The instructions shall give adequate guidance to Safely perform the retrofit or modification. If the lamp requires additional mechanical support then instructions for fitting shall be supplied. Eye protection, the appropriate warnings and instructions as indicated in AS/NZS IEC A7 CONSTRUCTION A7.1 a)for the replacement of lamps and replacement or general cleaning of optical components (such as diffusers or reflectors) without exposing live parts or unearthed exposed metal parts to personal contact. b) rotection against electric shock shall be maintained for all methods and positions of installation in normal use, having regard to the limitations indicated in the manufacturer s installation instructions. rotection shall be maintained after removal of all parts that can be removed by hand. c) Where necessary, to ensure continued safe use, metal parts shall be inherently non-corrosive, protected against corrosion or otherwise suitable for the purpose. A7.2 If lamps need to be used with a component that replaces the starter, the component shall have an internal 250 V HRC 0.5 A max. quick-acting fuse. A7.3 Lamps suitable for use in emergency luminaires shall comply with the requirements of AS in that specific luminaire. A7.4 Compatibility of electrical supply to the lamp, Lamps shall be constructed such that one end of the lamp has the lamp cap pins electrically bridged (Type A) or electrically isolated from each other (Type B) and the other end of the lamp has the line and neutral supply connected to the pins of that lamp cap. A8 INTERCHANGEABILITY lamp caps in accordance with IEC Gauges in accordance with IEC

43 age 43 of 50 Report No.: Annex 8 Variations to AS/NZS :1998 for application in Australia and/or New Zealand (AS/NZS :2014) Clause Requirement + Test Result - Remark Verdict If lamps need to operate in combination with a component which replaces the starter, this component shall be supplied together with the lamp. This component shall comply with the dimensions and electrical, mechanical and thermal tests required by Section 1 of AS/NZS A9 MASS The entire mass of a lamp shall not exceed 500 g for a G13-capped lamp The entire mass of a lamp shall not exceed 200 g for a G5-capped lamp These values may be exceeded where additional mechanical support is provided. Any additional mechanical support needed shall be provided with the lamp. Any additional mechanical support shall be double insulated and the fixing means shall not penetrate the enclosure of the luminaire. All tests shall be conducted with the additional mechanical support in place in accordance with the manufacturer s instructions. Compliance of any additional mechanical support shall be checked by the tests of Clause 4.14 of AS/NZS A10 DIMENSIONS Lamps shall have the dimensions of the corresponding lamps they are replacing in accordance with the relevant data sheets in IEC These dimensional requirements do not apply to any additional support mechanisms. A11 MECHANICAL REQUIREMENTS AND TESTS FOR CAS A11.1 Construction and assembly A11.2 Torque test, 1 N m then maintained for 30 s. Angular displacement After the test, the sample shall comply with protection against electric shock A11.3 Heat treatment test Where the lamp cap fixing uses cement or chemical bonding, the lamp cap fixing shall be subject to a treatment of 2000 ±50 h at a temperature of 85 ±5 C with the lamp not energized. After the treatment, the test specified in aragraph A11.2 shall be applied.

44 age 44 of 50 Report No.: Annex 8 Variations to AS/NZS :1998 for application in Australia and/or New Zealand (AS/NZS :2014) Clause Requirement + Test Result - Remark Verdict Screws and their fixings shall comply with the requirements of the torque test on screws of Section 4 of AS/NZS If two screws or a similar mechanical connection is used for fixing the cap to the tube, the test in this Clause (A11.3) is not applicable. A12 CREEAGE DISTANCES AND CLEARANCES The provisions of Section 11 of AS/NZS apply. A13 ROVISION FOR EARTHING The provisions of Section 7 of AS/NZS are not applicable. A14 TERMINALS The provisions of Section 14 and 15 of AS/NZS apply to supply terminals only; they are not applicable to lamp caps. A15 EXTERNAL AND INTERNAL WIRING The provisions of Section 5 of AS/NZS apply. A16 ROTECTION AGAINST ELECTRIC SHOCK A16.1 The provisions of Section 8 of AS/NZS apply. A16.2 The lamp shall be so constructed that, without any additional enclosure in the form of a luminaire, no internal metal parts, basic insulated external metal parts (other than caps), or live metal parts of the lamp cap or of the lamp itself are accessible when the lamp is installed in a lampholder in accordance with the relevant IEC lampholder data sheet. Metal parts of class II lamps which are insulated from live parts by basic insulation only are live parts for the purpose of this aragraph (A16). External metal parts other than the current-carrying metal parts of the cap shall not be or become live. Compliance: The accessibility shall be checked with test probe B of IEC 61032, applied with a force of 10 N. Any movable conductive material shall be placed in the most onerous position without using a tool. A16.3 Lamps incorporating a capacitor of capacitance exceeding 0.1 μf shall be provided with an internal discharge device, so that 1 s after disconnection the voltage between the pins of the lamp does not exceed 34 V. A16.4 There shall be no electrical continuity between the two ends of the lamp during the insertion.

45 age 45 of 50 Report No.: Annex 8 Variations to AS/NZS :1998 for application in Australia and/or New Zealand (AS/NZS :2014) Clause Requirement + Test Result - Remark Verdict Compliance shall be checked by the insulation resistance test and electric strength test of Section 10 of AS/NZS A17 ENDURANCE TEST AND THERMAL TESTS A17.1 The provisions of Section 12 of AS/NZS apply, together with the requirements of aragraphs A17.2 to A17.5. A17.2 The duration of the endurance test of Clause 12.3 of AS/NZS shall be 240 h (i.e cycles at normal operation) in free air. A17.3 During the thermal test of Clause 12.4 of AS/NZS , no accessible surface of the lamp shall exceed 70 C for metallic surfaces or 85 C for nonmetallic surfaces. A17.4 The surface temperature of inaccessible parts of the lamp cap shall not exceed 120 C. A17.5 Class III lamps shall, in addition, be subject to the abnormal operation test of Clause 12.5 of AS/NZS for a 240 V a.c. rating. The lamp shall not become unsafe during this test. A18 OWER REQUIREMENT The measured power of the lamp and any associated circuitry shall not be greater than 1.1 times the rated power. The measured power of the lamp and any associated circuitry shall not be greater than 1.1 times the rated power. A19 RESISTANCE TO DUST, SOLID OBJECTS AND MOISTURE Where the lamp is marked with an I rating in accordance with aragraph A5.2(g), the tests of Section 9 of AS/NZS shall be conducted on the lamp at its marked rating. A20 INSULATION RESISTANCE AND ELECTRIC STRENGTH The provisions of Section 10 of AS/NZS apply. A21 RESISTANCE TO HEAT, FIRE AND TRACKING The provisions of Section 13 of AS/NZS apply. A22 HOTOBIOLOGICAL HAZARD This Clause becomes applicable after May 16, The lamp shall not exceed the photobiological hazard ratings for Risk Group 1 (low risk), in accordance with Clause of AS/NZS IEC 62471:2011.

46 Annex 9 Variations to IEC :2000 for application in Australia and/or New Zealand (AS/NZS :2002 and AS/NZS IEC ) age 46 of 50 Report No.: Verdict Clause Requirement + Test Result - Remark Verdict 5 For Australia, rated supply voltage 230V/400V : Rated voltage: V; Rated test voltage:240 V. For Australia, rated test voltage 240V/415V : 8 TERMINALS, CABLES AND CORDS - Cables and cords: compliance with the relevant requirements of section 5 of AS/NZS arts of insulating material are resistant to flame and ignition Glow-wire test (750C): - part tested... : Bobbin of transformer and line chock, CB of driver, LED CB: No flame, no drop. - part not tested... : Glow-wire test (650C): - part tested... : Lamp cover: No flame, no drop. - part not tested... : Needle flame test (duration of flame or 30 s): - part tested... : part not tested... : -----

47 age 47 of 50 Report No.: Annex 10 hotobiological safety of lamps and lamp systems were according to standard IEC 62471:2006 and EN 62471:2008 and EU Directive 2006/25/EC. Exempt Group (This classification applied for all models) Exempt Group for model AGC-HB Optical hazard Test result Used hazard exposure limit Ref. 1. E s 5,399 x 10-6 W/m 2 0,001 W/m nm 2. E UVA 2,945 x 10-3 W/m 2 0,33 W/m nm 3. L B 4,105 x 10 W/m 2 sr 100 W/m 2 sr nm 4. E B (small source) nm 5. L R 5,361 x 10 3 W/m 2 sr 1,052 x 10 6 W/m 2 sr nm 6. E IR 0,000 W/m W/m nm 7. L IR 0,000 W/m 2 sr 2,555 x 10 5 W/m 2 sr nm 8. E H 1,510 W/m ,56 W/m nm

48 age 48 of 50 Report No.: icture 1: Overview 1 view of AGC-HB icture 2: Overview 2 of AGC-HB01-200

49 age 49 of 50 Report No.: icture 3: Internal view of AGC-HB (All models have the same internal construction) icture 4: Overview 1 view of AGC-HB (AGC-HB01-150, AGC-HB01-120, AGC-HB have the similar consturction except LED module)

50 age 50 of 50 Report No.: icture 5: Overview 2 view of AGC-HB icture 6: Mounting device