Testing Laboratory...: TÜV Rheinland Taiwan Ltd., Taichung Laboratory. Address...: 10F, No.219, Min Chuan Road, Taichung 403, Taiwan.

Transcription

1

2 age 1 of 11 TEST REORT Flat non-rewirable two-pole plugs, 2.5 A 250 V, with cord, for the connection of class II - equipment for household and similar purposes Report Reference No....: Tested by (+ signature)...: see cover sheet... Witnessed by (+ signature)...: see cover sheet... Supervised by (+ signature)...: see cover sheet... Approved by (+ signature)...: see cover sheet... Date of issue...: see cover sheet Testing Laboratory...: TÜV Rheinland Taiwan Ltd., Taichung Laboratory. Address...: 10F, No.219, Min Chuan Road, Taichung 403, Taiwan Testing location / procedure...: TL SMT WMT TM Address...: 10F, No.219, Min Chuan Road, Taichung 403, Taiwan Applicant s name...: Coming Data Co., Ltd Address...: 5F-1, No. 13, Wu Cheng 1st Rd. Hsin Chung City, Taipei Hsien, Test specification: Taiwan Standard...: :1990 Test procedure...: TÜV Rheinland Test approval Non-standard test method...: Test Report Form No....: EN50075B TRF originator...: OVE Master TRF...: dated Copyright 2004 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description...: EU lug Trade Mark...: Manufacturer...: Coming Data Co., Ltd Model and/or type reference...: C1220, C1215, C1210, C0920, C0915, C0540, C0530 Ratings...: I/: V~, 50/60Hz, 0.8A max.

3 age 2 of 11 Copy of marking plates

4 age 3 of 11 hotos for plug portion Soldering connection. in portion of the plug are fixed into the body by screw terminal. ossible test case verdicts: - test case does not apply to the test object...: - test object does meet the requirement...: (ass) - test object does not meet the requirement...: F(Fail)

5 age 4 of 11 Testing...: Date of receipt of test item...: Feb. 27, 2007 Date (s) of performance of tests...: Feb. 27, 2007 Apr. 23, 2007 General remarks: The present Test Report is not valid as a Test Report according to a Mutual Recognition Agreement (i.e. CCA, ENEC) unless signed by an approved Testing Laboratory and appended to a corresponding Certificate issued by a national Certification Body, signatory to the relevant Scheme. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(see Enclosure #)" refers to additional information appended to the report. "(see appended table)" refers to a table appended to the report. Throughout this report a point is used as the decimal separator. General product information: This EU plug portion is integrated with Direct lug-in Device, C12XY (C1220, C1215, C1210, C0920, C0915, C0540, C0530)

6 age 5 of 11 First testing set: Sample No. 1, 2 and 3 5 RATING 2.5 A AC 250 V V~, 0.8A max. 6 MARKING 6.1/.2 Rated current: 2.5 A 0.8A max. Rated voltage: 250 V V~ Nature of supply: ~ ~ Name of manufacturer or responsible vendor Type reference C1220, C1215, C1210, C0920, C0915, C0540, C Symbol for Class II construction not allowed Marked on Switch ower Supply. 6.4 Marking durable Marked on Switch ower Supply. Easily legible Test: 15 s water and 15 s petroleum spirit Marked on Switch ower Supply. Marked on Switch ower Supply. 7 DIMENSIONS Compliance with Standard Sheet 1 Complied. 1) Diagonal dimension of plug base 26.1 ± 0.5 mm C) 26.0 Top 26.4 Bottom mm Width of plug base 13.7 ± 0.7 mm D) 13.9 Top 14.1 Bottom mm Length of plug base 35.3 ± 0.7 mm E) 35.1 Top 35.3 Bottom mm These dimensions shall not be exceeded within a distance of 18mm from the engagement face of the plug along gripping surface. 18 mm min. F) 18.1 mm

7 age 6 of 11 The above dimensions shall be kept from the engagement face of the plug for min 4mm along gripping surface. 4mm min. G) 18.1 mm 2) 3) Between two pins (pin base) mm 18.5 mm Between two pins (pin top) mm 17.3 mm Diameter of pin (metallic part) 4 ± 0.06 mm H) 3.98 L 3.96 R mm The edges of the metal parts shall be chamfered or rounded off Complied. Diameter of pin (pin base) max. 4.0 mm 3.7 L 3.8 R mm Diameter of pin (middle part) max. 3.8 mm I) 3.4 L 3.4 R mm Length of pin except metal part mm J) 10.2 L 10.4 R mm in length 19 ± 0.5 mm K) 18.8 L 19.1 R mm Shape of pin end Rounded. Gauges of figures 1 and 2 Complied.

8 age 7 of 11 8 ROTECTION AGAINST ELECTRIC SHOCK 8.1 Test finger of fig. 3 After subjected a force of 75N for 60s, no impair occurred. Ambient temperature 35 C Force: 75 N Complied. 8.2 Gauge of fig. 4 The gauge did not come into contact with the engagement face of the plug. Ambient temperature: 35 ± 2 C 35 C 8.3 External parts of insulating material Complied. Material used: see table CONSTRUCTION 9.1 Non-rewirable plug Non-rewirable. 9.2 Switches, fuses and lampholders not incorporated No such kind of device incorporated. 9.3 ins of plug solid Complied. Checked according to clause ins of plug locked against rotation Complied. Checked according to clause 13.1 and in portion of the plug are fixed into the body by screw terminal. See also photo of plug portion 9.5 Effective permanent connections: - soldered, welded, crimped Soldering connection - screwed and snap-on connections not used Complied. - presoldered flexible conductor for crimping not permitted Complied. 9.6 Gripping operation: - length 55 mm Integrated with Switch ower Supply. - ball test Integrated with Switch ower Supply.

9 age 8 of RESISTANCE TO HUMIDITY No damage after 48 h R.H.: 95%, T ambient: 25 C, for 48 h 11 INSULATION RESISTANCE AND ELECTRIC STRENGTH 11.1 Resistance 5 MΩ (500 V, 1 min) 1000MΩ 11.2 Electric strength test (2000 V, 1 min): no flashover or breakdown No flashover or breakdown. 12 FLEXIBLE CORDS AND THEIR CONNECTION 12.1 Cords in compliance with HD 21.5 or HD 22.4 Non-flexible cords. 13 MECHANICAL STRENGTH 13.1 Compression test (150 N, 5 min) No deformation or any undue change of dimensions Tumbling barrel test: number of falls...: According to EN 60950, this test considered not applicable. Torque test on pins (0.4 Nm, 1 min) The pins did not turn after torque test Abrasion test ( movements): no damage No damage. 14 RESISTANCE TO HEAT AND TO AGEING Heating test (100 C, 1 h): no damage No damage a) ressure test (80 C, 20 N, 1 h): no damage Considered ball pressures test is severer than the pressure test, so the enclosure was subjected to ball pressure test instead. (80 C, 1 h). See also table b) ressure test (125 C, 20 N, 1 h): no damage As considered for ensure the safety aspect, the insulation material retaining the current-carrying parts was subjected to the ball pressure test (125 C, 1 h).

10 age 9 of CURRENT-CARRYING ARTS AND CONNECTIONS 15.1 Connections withstand the mechanical stresses occurring in normal use Complied Contact pressure Complied Material of current-carrying parts C3602, %; C3603BD, % 16 CREEAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH INSULATION Creepage distances and clearances between live parts 3 mm Creepage distances and clearances between live parts and accessible external surfaces 3 mm Distance through insulation 1.5 mm Creepage: 17.8 mm Clearance: 14.1 mm Creepage: 14.8 mm Clearance: 12.1 mm Integrated with Switch ower Supply. 4.6 mm from the live parts to accessible engagement surface. 17 RESISTANCE OF INSULATING MATERIAL TO ABNORMAL HEAT AND TO FIRE Glow-wire test (750 C for parts necessary to retain current-carrying parts in position): no visible flame, no sustained glowing or flames and glowing extinguish within 30 s after removal of glow-wire Glow-wire test (650 C for other parts): no visible flame, no sustained glowing or flames and glowing extinguish within 30 s after removal of glow-wire 750 C of glow-wire test was subjected. Flames and glowing at the insulation material retaining the current-carrying part extinguish within 30 s after removal of glow-wire. No ignition of tissue paper. See table C of glow-wire test was subjected. Flames and glowing at the plug enclosure extinguish within 30 s after removal of glow-wire. No ignition of tissue paper. See table 8.3

11 age 10 of 11 Second testing set: Sample No. 4, 5 and Moulded-on plugs ull test (100 times, 50 N, 1 s) Torque test (1 min): cross-sectional area 0.5 mm², 0.1 Nm: displacement 2 mm; no break in electrical connections cross-sectional area 0.75 mm², 0.15 Nm: displacement 2 mm; no break in electrical connections Integrated with Switch ower Supply Mechanical strength ull test with steel plate on pin (40 N, 70 C, 1 min): displacement of pin 1 mm After the test, no pin displacement occurred. 14 Resistance to heat and to ageing 14.2 Heating test (70 C, 168 h): no damage, no cracks visible No cracks visible. ressure test (5 N): no traces No traces. Third testing set: Sample No. 7, 8 and Flexible cords and their connection Flexing test ( flexings, 2.5 A, AC 250 V) - 10 N (cross-sectional area 0.75 mm²) - 20 N (cross-sectional area > 0.75 mm²) no damage Voltage drop 10 mv test current: - 1 A with H03 VH-Y A with other cords No flexible cord used.

12 age 11 of TABLE: list of critical components Object/part No. Enclosure Material AC lug in Holding Material Manufacturer/ trademark GE lastics Global roducts GE lastics Global roducts Type/model Technical data Standard Mark(s) of conformity SE1X(f1) V-1, 105 C UL 94 E61759 SE1X(f1) V-1, 105 C UL 94 E TABLE: ball pressure test of Insulating material allowed impression diameter (mm) : 2mm art Type/model Test temperature ( C) Impression diameter (mm) Enclosure Material SE1X(f1), GE lastics Global roducts AC lug in Holding Material SE1X(f1), GE lastics Global roducts