Shenzhen BST Technology Co., Ltd. LEDz Shine LVD REPORT. 98 Cormorant,Jakkalsfontein,Darling 7345,South Africa

Transcription

1 Report o.: BST Y-1SR-2 LEDz Shine LVD REORT repared For: LEDz Shine 98 Cormorant,Jakkalsfontein,Darling 7345,South Africa roduct ame: LED FLOOD LIGHT Trade: LEDz Shine 100W, LEDz Shine 10W, LEDz Shine 20W, Model : LEDz Shine 30W, LEDz Shine 40W, LEDz Shine 50W, LEDz Shine 60W, LEDz Shine 70W, LEDz Shine 80W, LEDz Shine 90W repared By : Shenzhen BST Technology Co., Ltd. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China Test Date: Aug. 12, 2013 Aug. 22, 2013 Date of Report : Aug. 22, 2013 Report o.: BST Y-1SR-2 Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 1 of 25

2 Report o.: BST Y-1SR-2 Testing Laboratory ame... : TEST REORT E Luminaires art 2: articular requirements Section Five Floodlight Shenzhen BST Technology Co., Ltd. Address... : Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China Testing location... : Applicant's ame... : Shenzhen BST Technology Co., Ltd. LEDz Shine Address... : 98 Cormorant,Jakkalsfontein,Darling 7345,South Africa Manufacturer.. : LEDz Shine Address... : 98 Cormorant,Jakkalsfontein,Darling 7345,South Africa Test specification Standard... : rocedure deviation... : on-standard test method... : Test item description... : LED FLOOD LIGHT Trademark... : E :1998 used in conjunction with E :2008+A11:2009 E 62493:2010 CE-LVD /A Model and/or type reference... : LEDz Shine 100W, LEDz Shine 10W, LEDz Shine 20W, LEDz Shine 30W, LEDz Shine 40W, LEDz Shine 50W, LEDz Shine 60W, LEDz Shine 70W, LEDz Shine 80W, LEDz Shine 90W Rating(s)... : 230V~, 50/60Hz, 100W Test case verdicts Test case does not apply to the test object.. : /A Test item does meet the requirement... : (ass) Test item does not meet the requirement... : F(ail) Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 2 of 25

3 Report o.: BST Y-1SR-2 General remarks This report shall not be reproduced except in full without the written approval of the testing laboratory. The test results presented in this report relate only to the item(s) tested. (see remark #)" refers to a remark appended to the report. "(see Annex #)" refers to an annex appended to the report. Clause numbers between brackets refer to clauses in E General product information: The series products have the same circuit diagram, CB layout and functionality. The differences are the model name, so, we select LEDz Shine 100W to test. Copy of marking plate: roduct : LED FLOOD LIGHT Rated: 230V~, 50/60Hz, 100W Model: LEDz Shine 100W LEDz Shine I65 repared by : Engineer Reviewer : Supervisor Approved & Authorized Signer : Christina / Manager Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 3 of 25

4 Report o.: BST Y-1SR-2 E & E (0) SCOE 5.1 (0.1) More sections applicable...: Yes ] o [ ] 5.4 (2) CLASSIFICATIO 5.4 (2.2) Type of protection...: Class I 5.4 (2.3) Degree of protection...: I (2.4) ortable or handheld luminaire...: o Fixed luminaire suitable for normally flammable surfaces...: Fixed luminaire suitable for non-combustible materials only...: 5.4 (2.5) Luminaire for normal use...: Yes Luminaire for rough service...: o Yes o 5.5 (3) MARKIG 5.5 (3.2) Mandatory markings osition of the marking Markings on the enclosure Format of symbols/text 5.5 (3.3) Additional information Language of instructions English 5.5 (3.3.1) Combination luminaires 5.5 (3.3.2) ominal frequency in Hz 50/60Hz 5.5 (3.3.3) Operating temperature (3.3.4) Symbol or warning notice 5.5 (3.3.5) Wiring diagram 5.5 (3.3.6) Special conditions 5.5 (3.3.7) Metal halid lamp luminaire warning 5.5 (3.3.8) Limitation for semi-luminaires ot semi-luminaires 5.5 (3.3.9) ower factor and supply current 5.5 (3.3.10) 5.5 (3.3.11) 5.5 (3.3.12) Suitability for use indoors Luminaires with remote control o remote control Clip-mounted luminaire - warning ot clip-mounted luminaire Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 4 of 25

5 Report o.: BST Y-1SR-2 E & E (3.3.13) 5.5 (3.3.14) 5.5 (3.3.15) 5.5 (3.3.16) 5.5 (3.3.17) 4.5 (3.3.18) Specifications of protective shields Symbol for nature of supply ~ Rated current of socket outlet o socket outlet Rough service luminaire Mounting instruction for type Y, type Z and some type X attachments on-ordinary luminaires with VC cable Type Y 5.5 (3.4) Test with water 15s with water Test with hexane 15s with hexane Legible after test Markings Legible Label attached (4) COSTRUCTIO.1 (-) At least IX3 I65.2 (-) Lampholder brackets.3 (-) Adjusting means.4 (-) Controlling components.5 (-) Fixing device Wind force test.6 (-) Locking system.7 (-) Vibration resistance.8 (-) Glass cover Visual inspection (4.2) Components replaceable without difficulty (4.3) Wireways smooth and free from sharp edges Wireways smooth and free from sharp edges (4.4) Lampholders (4.4.1) Integral lampholder (4.4.2) Wiring connection (4.4.3) Lampholder for end-to-end mounting (4.4.4) ositioning (4.4.5) eak pulse voltage (4.4.6) Centre contact (4.4.7) Rough service luminaires Ordinary luminaires Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 5 of 25

6 Report o.: BST Y-1SR-2 E & E (4.4.8) Lamp connectors (4.5) Starter holders- -- Starter holder in luminaires other than class II Starter holder class II construction (4.6) Terminal blocks Tails Unsecured blocks (4.7) Terminals and supply connections (4.7.1) Contact to metal parts (4.7.2) Test 8 mm live conductor Test 8 mm earth conductor (4.7.3) Terminals for supply conductors (4.7.4) Terminals other than supply connection (4.7.5) Heat-resistant wiring/sleeves Heat-resistant wiring (4.7.6) Multi-pole plug (4.8) Switches: - adequate rating - adequate fixing - polarized supply (4.9) Insulating lining and sleeves (4.9.1) Retainment Method of fixing...: (4.9.2) Insulated linings and sleeves a) & c) Insulation resistance and electric strength b) Ageing test. Temperature ( C)...: (4.10) Insulation of Class II luminaires (4.10.1) (4.10.2) o contact, mounting surface accessible metal parts wiring of basic insulation Safe installation fixed luminaires Capacitors Interference suppression capacitors according to IEC Assembly gaps: -- - not coincidental - no straight access with test probe Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 6 of 25

7 Report o.: BST Y-1SR-2 E & E (4.10.3) Retainment of insulation: - fixed - unable to be replaced; luminaire inoperative - sleeves retained in position - lining in lampholder (4.11) Electrical connections -- (4.11.1) (4.11.2) (4.11.3) (4.11.4) (4.11.5) (4.11.6) Contact pressure Screws: ot transmitted through insulating material - self-tapping screws Visual inspection - thread-cutting screws - at least two self-tapping screws Screw locking: - spring washer - rivets Material of current-carrying parts o contact to wood o wood material in the luminaires Electro-mechanical contact systems (4.12) Mechanical connections and glands -- (4.12.1) Screws not made of soft metal Visual inspection Screws of insulating material Torque test: torque (m); part...: 0.6m (4.12.2) (4.12.4) Torque test: torque (m); part...: Torque test: torque (m); part...: Screws with diameter < 3 mm screwed into metal Locked connections: - fixed arms; torque (m)...: - lampholder; torque (m)...: - push-button switches; torque 0,8 m...: Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 7 of 25

8 Report o.: BST Y-1SR-2 E & E (4.12.5) Screwed glands; force ()...: (4.13) Mechanical strength -- (4.13.1) (4.13.3) (4.13.4) (4.13.6) Impact tests: - fragile parts; energy (m)...: 0.5 m - other parts; energy (m)...: 0.75 m 1) live parts ot access 2) linings 3) protection Continue to afford the degree of protection against ingress of dust, solid objects and moisture 4) covers o break Straight test finger Rough service luminaires -- a) fixed b) hand-held c) delivered with a stand d) for temporary installations and suitable for mounting on a stand Tumbling barrel (4.14) Suspensions and adjusting devices -- (4.14.1) (4.14.2) Mechanical load: A) four times the weight B) torque 2,5 m C) bracket arm; bending moment (m)...: D) load track-mounted luminaires E) clip-mounted luminaires, glass-shelve. Thickness (mm)...: metal rod. Diameter (mm)...: Load to flexible cables -- Mass (kg)...: Stress in conductors (/mm²)...: Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 8 of 25

9 Report o.: BST Y-1SR-2 E & E (4.14.3) (4.14.4) (4.14.5) (4.14.6) Adjusting devices: - flexing test; number of cycles...: - strands broken - electric strength test afterwards ormal Telescopic tubes: cords not fixed to tube; no strain on conductors Guide pulleys Strain on socket-outlets o socket-outlet (4.15) Flammable materials: (4.15.2) - glow-wire test 650 C - spacing 30 mm - screen withstanding test of screen dimensions - no fiercely burning material - thermal protection - electronic circuits exempted Luminaires made of thermoplastic material with lamp control gear -- a) construction b) temperature sensing control c) surface temperature (4.16) Luminaires marked with F-symbol -- (4.16.1) (4.16.2) (4.16.3) o lamp control gear (compliance with Section 12) Lamp control gear spacing: - spacing 35 mm - spacing 10 mm Thermal protection: - in lamp control gear - external - fixed position - temperature marked lamp control gear The test of 12.6 Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 9 of 25

10 Report o.: BST Y-1SR-2 E & E (4.17) Drain holes Clearance at least 5 mm (4.18) Resistance to corrosion: -- (4.18.1) (4.18.2) (4.18.3) - rust-resistance - season cracking in copper - corrosion of aluminium (4.19) Ignitors compatible with ballast (4.20) Rough service vibration (4.21) rotective shield: (4.21.1) (4.21.2) (4.21.3) (4.21.4) Shield fitted articles from a shattering lamp not impair safety o direct path Impact test on shield Glow-wire test on lamp compartment (4.22) Attachments to lamps o attachments (4.23) Semi-luminaires comply class II (4.24) UV radiation, metal halide lamps (4.25) o sharp point or edges o sharp points or edges (4.26) Short-circuit protection: -- (4.26.1) (4.26.2) (4.26.3) Uninsulated accessible SELV parts Short-circuit test Test chain according to IEC (11) CREEAGE DISTACES AD CLEARACES Working voltage (V)...: 230V~ Voltage form Sinusoidal [ ] on-sinusoidal [ ] TI < 600 [ ] > 600 [ ] Rated pulse voltage (Kv)...: Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 10 of 25

11 Report o.: BST Y-1SR-2 E & E (1) Current-carrying parts of different polarity: cr (mm); cl (mm)...: (2) Current-carrying parts and accessible parts: cr (mm); cl (mm)...: (3) arts becoming live due to breakdown of basic insulation and metal parts: cr (mm); cl (mm)...: (4) Outer surface of cable where it is clamped and metal parts: cr (mm); cl (mm)...: (5) Current-carrying parts of switches and metal parts, after removal of insulation: cr (mm); cl (mm)...: (6) Current-carrying parts and supporting surface: cr (mm); cl (mm)...: Cr >2.5mm, Cl>1.5mm Cr >2.5mm, Cl>1.5mm Cr >2.5mm, Cl>1.5mm 5.8 (7) ROVISIO FOR EARTHIG 5.8 ( ) 5.8 ( ) Accessible metal parts Metal parts in contact with supporting surface Resistance < 0,5 Ω 0.07< 0,5 Ω Two self-tapping screws used Thread-forming screws Connector earthing first Earth continuity in joints etc. 5.8 (7.2.4) Locking of clamping means Compliance with (7.2.5) Earth terminal integral part of connector socket 5.8 (7.2.6) Earth terminal adjacent to mains terminals 5.8 (7.2.7) Electrolytic corrosion of the earth terminal 5.8 (7.2.8) Material of earth terminal 5.8 (7.2.10) 5.8 (7.2.11) Contact surface bare metal Class II luminaire for looping-in Earthing core coloured green-yellow Length of earth conductor 5.9 (14) SCREW TERMIALS Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 11 of 25

12 Report o.: BST Y-1SR-2 E & E Separately approved; component list art of the luminaire 5.9 (15) SCREWLESS TERMIALS Separately approved; component list art of the luminaire (5) EXTERAL AD ITERAL WIRIG (5.2) Supply connection and external wiring -- (5.2.1) (5.2.2) (5.2.3) (5.2.5) (5.2.6) (5.2.7) (5.2.8) Means of connection...: ower cord Type of cable...: ominal cross-sectional area (mm²)...: Type of attachment, X, Y or Z Type Y Type Z not connected to screws Cable entries: - suitable for introduction - adequate degree of protection Cable entries through rigid material have rounded edges Insulating bushings: - suitably fixed - material in bushings (5.2.9) (5.2.10) - tubes or guards made of insulating material Locking of screwed bushings Cord anchorage: - covering protected from abrasion - clear how to be effective - no mechanical or thermal stress - no tying of cables into knots etc. - insulating material or lining Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 12 of 25

13 Report o.: BST Y-1SR-2 E & E ( ) Cord anchorage for type X attachment: ( ) ( ) (5.2.11) (5.2.12) (5.2.13) (5.2.14) (5.2.15) (5.2.16) a) at least one part fixed b) types of cable c) no damaging of the cable d) whole cable can be mounted e) no touching of clamping screws f) metal screw not directly on cable g) replacement without special tool Glands not used as anchorage Labyrinth type anchorages Adequate cord anchorage for type Y and type Z attachment Tests: - impossible to push cable; unsafe - pull test: 25 times; pull ()...: 60 - torque test: torque (m)...: 0.25m - displacement 2 mm 0.03mm 2 mm - no movement of conductors - no damage of cable or cord External wiring passing into luminaire Looping-in terminals Wire ends not tinned Wire ends tinned: no cold flow Mains plug same protection Class III luminaire plug Colour code low voltage Appliance inlets (IEC 60320) Appliance couplers of class II type (5.3) Internal wiring (5.3.1) Internal wiring of suitable size and type Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 13 of 25

14 Report o.: BST Y-1SR-2 E & E ( ) ( ) ( ) ( ) ( ) ( ) (5.3.2) Through wiring - not delivered/ mounting instruction - factory assembled - socket outlet loaded (A)...: - temperatures...: Green-yellow for earth only Internal wiring connected directly to fixed wiring Cross-sectional area (mm²)...: 0.5mm² Insulation thickness Extra insulation added where necessary Internal wiring connected to fixed wiring via internal current-limiting device -- Adequate cross-sectional area and insulation thickness Double or reinforced insulation for class II Conductors without insulation SELV current-carrying parts Insulation thickness other than VC or rubber Sharp edges etc. o moving parts of switches etc. Joints, raising/lowering devices Telescopic tubes etc. Telescopic tubes o twisting over 360 Twisting over 360 (5.3.3) Openings Bushings not removable Bushings in sharp openings Cables with protective sheath (5.3.4) Joints and junctions effectively insulated (5.3.5) Strain on internal wiring (5.3.6) Wire carriers (5.3.7) Wire ends not tinned Wire ends tinned: no cold flow Wire ends tinned: no cold flow Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 14 of 25

15 Report o.: BST Y-1SR-2 E & E (8) ROTECTIO AGAIST ELECTRIC SHOCK 5.11 (8.2.1) Live parts not accessible o access of live part in normal use rotection in any position Double-ended tungsten filament lamp Insulation lacquer not reliable Double-ended high pressure discharge lamp 5.11 (8.2.2) ortable luminaire adjusted in most unfavourable position o insulation lacquer and similar materials as protection against electric shock 5.11 (8.2.3) Class II luminaire: -- - basic insulated metal parts not accessible during starter or lamp replacement - basic insulation not accessible other than during starter or lamp replacement - glass protective shields not used as supplementary insulation Class I luminaire with BC lampholder 5.11 (8.2.4) ortable luminaire: -- - protection independent of supporting surface - terminal block completely covered 5.11 (8.2.6) Covers reliably secured 5.11 (8.2.7) Discharging of capacitors 0,5 µf ortable plug connected luminaire with capacitor Other plug connected luminaire with capacitor Discharge device on or within capacitor Discharge device mounted separately 5.12 (12) EDURACE TEST AD THERMAL TEST 5.12 (12.3) Endurance test: - mounting-position...: - test temperature ( C)...: 35 - total duration (h)...: 168h - supply voltage: Un factor; calculated voltage (V)...: 230X1.1=253V - lamp used...: Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 15 of 25

16 Report o.: BST Y-1SR-2 E & E (12.3.2) After endurance test: -- - no part unserviceable - luminaire not unsafe Visual inspection - no damage to track system - marking legible Marking legible - no cracks, deformation etc. o cracks, deformation etc (12.4) Thermal test (normal operation) (-) Temperature reduction 5.12 (12.5) Thermal test (abnormal operation) 5.12 (12.6) Thermal test (failed lamp control gear condition): 5.12 (12.6.1) 5.12 (12.6.2) - case of abnormal conditions...: - electronic lamp control gear - measured winding temperature ( C): at 1,1 Un : - measured mounting surface temperature ( C): at 1,1 Un...: - calculated mounting surface temperature ( C).: - track-mounted luminaires Temperature sensing control - case of abnormal conditions...: - thermal link - manual reset cut-out - auto reset cut-out - measured mounting surface temperature ( C):...: - track-mounted luminaires 5.12 (12.7) Thermal test (failed lamp control gear in plastic luminaires): 5.12 (12.7.1) 5.12 (12.7.2) - case of abnormal conditions...: - measured winding temperature ( C) at 1,1 Un.: - measured temperature of fixing point/ exposed part ( C) at 1,1 Un...: - calculated temperature of fixing point/ exposed part ( C)...: Temperature sensing control Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 16 of 25

17 Report o.: BST Y-1SR-2 E & E thermal link - manual reset cut-out - auto reset cut-out - measured temperature of fixing point/ exposed part ( C)...: 5.13 (9) RESISTACE TO DUST, SOLID OBJECTS AD MOISTURE 5.13 (9.2) Tests for ingress of dust, solid objects and moisture: - classification according to I...: I65 - mounting position during test...: - fixing screws tightened; torque (m)...: - tests according to clauses...: - electric strength test afterwards a) no deposit in dust-proof luminaire b) no talcum in dust-tight luminaire c) no trace of water on current-carrying parts or where it could become a hazard d) i) For luminaires without drain holes no water entry d) ii) For luminaires with drain holes no hazardous water entry e) no water in watertight luminaire f) no contact with live parts (I 2X) f) no entry into enclosure (I 3X and I 4X) 5.13 (9.3) Humidity test 48 h R.H.:93% T:25 48H 5.14 (10) ISULATIO RESISTACE AD ELECTRIC STREGTH 5.14 (10.2.1) Insulation resistance test -- Insulation resistance (MΩ): SELV: - between current-carrying parts of different polarity...: - between current-carrying parts and mounting surface...: - between current-carrying parts and metal parts of the luminaire...: Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 17 of 25

18 Report o.: BST Y-1SR-2 E & E (10.2.2) 5.14 (10.3.1) Other than SELV: - between live parts of different polarity...: >2MΩ - between live parts and mounting surface...: >2MΩ - between live parts and metal parts...: >2MΩ - between live parts of different polarity through action of a switch...: Electric strength test -- Dummy lamp Luminaires with ignitors after 24 h test Luminaires with manual ignitors Test voltage (V): SELV: - between current-carrying parts of different polarity...: - between current-carrying parts and mounting surface...: - between current-carrying parts and metal parts of the luminaire...: Other than SELV: - between live parts of different polarity...: 1460V, no broken - between live parts and mounting surface...: 1460V, no broken - between live parts and metal parts...: 1460V, no broken - between live parts of different polarity through action of a switch...: Leakage current (Ma)...: 0.08mA <limit:1.0ma 5.15 (13) RESISTACE TO HEAT, FIRE AD TRACKIG 5.15 (13.2.1) 5.15 (13.3.1) 5.15 (13.3.2) Ball-pressure test: - part tested; temperature ( C)...: - part tested; temperature ( C)...: eedle flame test (10 s): - part tested...: - part tested...: Glow-wire test (650 C): Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 18 of 25

19 Report o.: BST Y-1SR-2 E & E (13.4.1) ( ) - part tested...: - part tested...: Tracking test: part tested...: COMMO MODIFICATIOS For luminaires connected by tails, information about terminal block (5.2.2) Cables equal to HD 21 S2 or HD 22 S2 (5.2.15) Colour code low voltage ZB AEX ZB, SECIAL ATIOAL CODITIOS (2.2) Class 0 not accepted (3.3) DK: power supply cord with label IT: warning label on Class 0 luminaire (4.5.1) DK: socket-outlets (4.5.1) FR: socket-outlets (5.2.1) DK, FI, SE, GB: type of plug ZC AEX ZC, ATIOAL DEVIATIOS (13.3) DK: eedle flame test or glow-wire test 750 C for luminaires in access routes (13.3) GB: Requirements according to United Kingdom Building Regulation (13.3.2) FR: Glow-wire test 850 C alt. 750 C for luminaires in premises open to public and workers AEX 1 Components Object / part o. Manufacturer/ trademark Type / model Technical data Standard Mark(s) of conformity LED Driver MEA WELL CLG A Input: V~, 50/60Hz, 2.0A Output:36Vdc, 4.2A -- CE AEX 2: temperature measurements, thermal tests of Section 12 Type reference...: See page 2 Lamp used...: Lamp control gear used...: Mounting position of luminaire...: ormal position Supply wattage (W)...: 100W Supply voltage (V)...: -- Supply current (A)...: -- Calculated power factor...: -- Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 19 of 25

20 Report o.: BST Y-1SR-2 Table: measured temperatures corrected for ta = 25 C: - abnormal operating mode...: -- - test 1: rated voltage...: -- - test 2: 1,06 times rated voltage or 1,05 times 230X1.06=243.8V rated wattage... : - test 3: Load on wiring to socket-outlet, -- 1,06 times voltage or 1,05 times wattage... : - test 4: 1,1 times rated voltage or 1,05 times rated wattage... : -- temperature ( C) of part clause 12.4 normal clause 12.5 abnormal test 1 test 2 test 3 limits test 4 limit Enclosure surface Ref Enclosure Inside Internal wiring ower cord Ambient AEX 3: screw terminals (part of the luminaire) (14) SCREW TERMIALS (14.2) Type of terminal...: Rated current (A)...: ( ) One or more conductors ( ) Special preparation ( ) Terminal size Cross-sectional area (mm²)...: (14.3.3) Conductor space (mm)...: (14.4) Mechanical tests -- (14.4.1) Minimum distance (14.4.2) Cannot slip out (14.4.3) Special preparation (14.4.4) ominal diameter of thread (metric ISO thread)... : External wiring o soft metal (14.4.5) Corrosion (14.4.6) ominal diameter of thread (mm)...: Torque (m)...: (14.4.7) Between metal surfaces Lug terminal Mantle terminal ull test; pull ()...: (14.4.8) Without undue damage AEX 4: screwless terminals (part of the luminaire) (15) SCREWLESS TERMIALS (15.2) Type of terminal...: Rated current (A)...: (15.3.1) Material (15.3.2) Clamping (15.3.3) Stop (15.3.4) Unprepared conductors (15.3.5) ressure on insulating material (15.3.6) Clear connection method Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 20 of 25

21 Report o.: BST Y-1SR-2 (15.3.7) Clamping independently (15.3.8) Fixed in position ( ) Conductor size Type of conductor (15.5.1) Terminals internal wiring ( ) ull test spring-type terminals (4, 4 samples) ( ) ull test pin or tab terminals (4, 4 samples) Insertion force not exceeding 50 (15.5.2) ermanent connections: pull-off test (20 ) (1) Electrical tests Voltage drop (mv) after 1 h (4 samples)...: Voltage drop of two inseparable joints umber of cycles...: Voltage drop (mv) after 10 th alt. 25 th cycle (4 samples)...: Voltage drop (mv) after 50 th alt. 100 th cycle (4 samples)...: After ageing, voltage drop (mv) after 10 th alt. 25 th cycle (4 samples)...: After ageing, voltage drop (mv) after 50 th alt. 100 th cycle (4 samples)...: (15.7) Terminals external wiring Terminal size and rating (15.8.1) ull test spring-type terminals (4 samples); pull () ull test pin or tab terminals (4 samples); pull () (15.9) Contact resistance test Voltage drop (mv) after 1 h -- terminal voltage drop (mv) Voltage drop of two inseparable joints Voltage drop after 10th alt. 25th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Continued ageing: voltage drop after 10th alt. 25th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Continued ageing: voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 21 of 25

22 Report o.: BST Y-1SR-2 E 62493: ) Test Summary: The EMF (Electromagnetic Field) measurement at the highest level component for the LED FLOOD LIGHT, Model: LEDz Shine 100W was shown as below: Test Result Summary: Model Maximal test result Weighted result Maximum ass / Fail (ma/m²) Limit(mA/m²) LEDz Shine 100W /A 8 ass 2) Test condition: ower Source of EUT: 230V, 50/60Hz Background Level: 1.034% Operation Condition: EUT continuously Measuring Distance: 50cm on. Coupling Factor: 0.14 < 0.85 Ambient Condition: 25 Sensor Locations: Around 3) Test data: (unit: ma/m²) Measuring ositions Front Left Right Rear Top Bottom Test result ) otes: 1. In accordance to E 62493, The measurement frequency range considered is from 20 khz to 10 MHz. 2. Measure set-up 2. Test tine: 15mins. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 22 of 25

23 Report o.: BST Y-1SR-2 AEX A: hoto-documentation Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 23 of 25

24 Report o.: BST Y-1SR-2 hoto 1 Overview hoto 2 Bottom View Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 24 of 25

25 Report o.: BST Y-1SR-2 hoto 3 Internal View Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 25 of 25