Test report: 13/ Date January 20 th,2014 Page 1 of 52

Transcription

1 LGAI LGAI Technological Center, S.A. Campus de la UAB Apartado de Correos 18 E Bellaterra (Barcelona) T F TEST REORT Test report: 13/ Date January 20 th,2014 age 1 of 52 etitioner s reference Nº 9/LE/894 LGAI Technological Center, S.A. GONZÁLEZ SORIANO, S.A. arque Tecnológico de Asturias, arcela Llanera (ASTURIAS)) The received material Emergency luminaire supplied by central source and no permanent operation, trademark NORMALUX model EURORISMA EH-SFL8, with internal id. nr. 1765/1. Has been tested and found in conformity with the applied specifications of the standard/s UNE-EN :2009+A11:2009 UNE-EN :1999+A1:2003+Corr.2006+A2:2008 UNE-EN :2009+A1:2011* UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* UNE-EN 50102:1996+A1:1999+Corr:2002+A1/CORR: Standards marked with symbol * are not included within EC accreditation scope. Rated characteristics Rated voltage (V)... : Rated power (W)... : 230 AC 8W Frequency (Hz)... : 50/60 Lamp... : Classification... : Installation type... : Fluorescent T5 Class II Fixed rotection degree against ingress of water: I65 rotection degree against impact..: Rated luminous flux.....: IK lm Albert Marginet Technical Manager Electrical & Electronics LGAI Technological Center, S.A. The results reported in this document relate only to the sample, product or item submitted to the Laboratory and described above, having been tested under the conditions established in this document. The reproduction of this document, is only authorised if it s made in its totality. The document has 52 pages from which 6 are appendix. LGAI Technological Center,S.A. Inscrita en el Registro Mercantil de Barcelona, Tomo , Folio 1, Hoja Nº B Inscripción 1ª.C.I.F. A

2 UNE-EN :1999+A1:2003+Corr.2006+A2:2008 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* UNE-EN 50102:1996+A1:1999+CORR:2002+A1 CORR:2002 Test report: 13/ age 2 of 52 UNE-EN :1999+A1:2003+Corr.2006+A2:2008 LUMIIRES. ART 2-22: ARTICULAR REQUIREMENTS. LUMIIRES FOR EMERGENCY LIGHTING UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* LAM CONTROLGEAR -- ART 2-3: ARTICULAR REQUIREMENTS FOR A.C. SULIED ELECTRONIC BALLASTS FOR FLUORESCENT LAMS UNE-EN 50102:1996+A1:1999+CORR:2002+A1 CORR:2002 DEGREES OF ROTECTION ROVIDED BY ENCLOSURES FOR ELECTRICAL EQUIMENT AGAINST EXTERL MECHANICAL IMACTS (IK CODE) Test report... : 13/ Tests conducted by (name and signature)... : Oscar Martín Verified by (name and signature)... : Albert Marginet Date of receipt of test item... : December 04 th,2013 Date of performance of test (start). : December 04 th,2013 Date of performance of test ( end ) : January 17 th,2014 Applicant's Name... : GONZÁLEZ SORIANO, S.A. Address... : arque Tecnológico de Asturias, arcela Llanera (ASTURIAS) Testing Laboratory Name... : LGAI Technological Center, S.A. Address... : Campus de la UAB Apdo. Correos Bellaterra (Barcelona España) Test item description... : Emergency luminaire supplied by central source and no permanent operation Manufacturer... : Gonzálex Soriano, S.A. Brand... : Normalux Model... : EURORISMA EH-SFL8 Reference... : --- Internal identification number... : 1765/1

3 UNE-EN :1999+A1:2003+Corr.2006+A2:2008 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* UNE-EN 50102:1996+A1:1999+CORR:2002+A1 CORR:2002 Test report: 13/ age 3 of 52 Rated characteristics Rated voltage (V)... : Rated power (W)... : 8- Current (A)... : --- Frequency (Hz)... : 50/60- Class equipment... : Class II Luminaire type... : Fixed Lamp... : Fluorescent T5 Degree of protection... : I65 Degree of protection against impact : IK07 Rated luminous flux (lm)... : 340 Environmental conditions during tests Temperature (ºC)... : 20,0 22,9 Relative humidity (%)... : 32-43

4 UNE-EN :1999+A1:2003+Corr.2006+A2:2008 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* UNE-EN 50102:1996+A1:1999+CORR:2002+A1 CORR:2002 Test report: 13/ age 4 of 52 Uncertainty of measurement The reported uncertainty is an expanded uncertainty calculated using a coverage factor k of 2 which gives a level of confidence of approximately 95 %. The typical uncertainty of measurement has been determined according to EA4-02. Temperature = 1 ºC Current = 1,5 % Voltage = 0,7 % Temperature = 1 ºC Current = 1,5 % Voltage = 0,7 % Test case verdicts Test case does not apply to the test object... : Test item does meet the requirement... : Test item does not meet the requirement... : The test requirements had nt been checked... : Observation over the test results (Num)... : N(ot)A(pplied) (ass) F(ail) N(ot)T(ested) OBS(ervation) General remarks The results reported in this document relate only to the sample, product or item submitted to the Laboratory and described above, having been tested under the conditions stablished in this document. In case of discrepancies between the English and Spanish versions, the Spanish version prevails over the English one. Service Quality Assurance Applus+, guarantees that this work has been made in accordance with our Quality and Sustainability System, fulfilling the contractual conditions and legal norms. Within our improvement program we would be grateful if you would send us any commentary that you consider opportune, to the person in charge who signs this document, or to the Quality Manager of Applus+, in the following address: satisfaccion.cliente@applus.com

5 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 5 of (0) GENERAL TEST REQUIREMENTS (0.1) Information for luminaire design considered Standard Yes No 22.2 (0.3) More sections applicable... : Yes No 22.4 (2) CLASSIFICATION (2.2) Type of protection (Class 0 excluded)... : Class II 22.4 (2.3) Degree of protection (Requirement: Ordinary)... : I (2.4) Luminaire suitable for direct mounting on normally flammable surfaces... : Yes No Luminaire not suitable for direct mounting on normally flammable surfaces...: Yes No 22.4 (2.5) Luminaire for normal use... : Yes No Luminaire for rough service... : Yes No Annex B (-) Classification code Z 0 ***** (3) MARKING (3.2) Mandatory markings osition of the marking Format of symbols/text 22.5 (3.3) Additional information --- Language of instructions Spanish/English 22.5 (3.3.1) Combination luminaires 22.5 (3.3.2) Nominal frequency in Hz 50/ (3.3.3) Operating temperature 22.5 (3.3.4) Symbol or warning notice 22.5 (3.3.5) Wiring diagram 22.5 (3.3.6) Special conditions 22.5 (3.3.7) Metal halide lamp luminaire warning 22.5 (3.3.8) Limitation for semi-luminaires 22.5 (3.3.9) ower factor and supply current 22.5 (3.3.10) Suitability for use indoors 22.5 (3.3.11) Luminaires with remote control 22.5 (3.3.12) Clip-mounted luminaire warning

6 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 6 of (3.3.13) Specifications of protective shields 22.5 (3.3.14) Symbol for nature of supply 22.5 (3.3.15) Rated current of socket outlet 22.5 (3.3.16) Rough service luminaire 22.5 (3.3.17) Mounting instruction for type Y, type Z and some type X attachments 22.5 (3.3.18) Non-ordinary luminaires with VC cable 22.5 (3.3.19) rotective conductor current in instruction if applicable 22.5 (3.3.20) rovided with information if not intended to be mounted within arms reach 22.5 (3.4) Test with water Test with hexane Legible after test Label attached (-) Supply voltage 230V AC (-) Classification according to annex B Z 0 ***** (-) Correct replacement lamp F8T5 8W (-) Range of ambient temperatures 25ºC (-) Fuse ratings and/or indicator lamps No replaceable (-) Facilities to simulate normal supply failure (-) Marked with correct battery replacement incl. battery type and rated voltage If non-replaceable batteries a label according to 3.2.b) of IEC No battery No battery (-) Battery marked with date of manufacture No battery Space provided on battery label for installers marking (-) Correct lamp replacement for combined emergency luminaires No battery No combined luminaire Green dot with min 5 mm diameter See above Instruction leaflet and (-) Replacement of battery or luminaire No battery (-) Details of test facilities

7 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 7 of (-) Details of connection leads (-) Details of device which changes the mode of operation (-) hotometric data available (-) Any normal preparation procedure (-) osition of the marking in and (-) rovided with warning if intended for external plug and socket connections (-) Instruction leaflet specify if lamp and/or battery is/are non-replaceable No battery and lamp is replaceable 22.6 (4) CONSTRUCTION (4.2) Components replaceable without difficulty Lamp 22.6 (4.3) Wireways smooth and free from sharp edges 22.6 (4.4) Lampholders (LED, no lampholders) (4.4.1) Integral lampholder 22.6 (4.4.2) Wiring connection No wires 22.6 (4.4.3) Lampholder for end-to-end mounting 22.6 (4.4.4) ositioning pressure test (N) : 15N After test the lampholder comply with relevant standard sheets and show no damage After test on single-capped lampholder the lampholder have not moved from its position and show no permanent deformation Double capped lampholder - bending test (N) : ---, fluorescent lamp After test the lampholder have not moved from its position and show no permanent deformation See above 22.6 (4.4.5) eak pulse voltage Without starter 22.6 (4.4.6) Centre contact Fluorescent lamp 22.6 (4.4.7) arts in rough service luminaires resistant to tracking No for rough service 22.6 (4.4.8) Lamp connectors Not present 22.6 (4.4.9) Caps and bases correctly used Fluorescent lamp

8 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 8 of (4.5) Starter holders --- Starter holder in luminaires other than class II Not present Starter holder class II construction Not present 22.6 (4.6) Terminal blocks --- Tails rovided with luminaire Unsecured blocks See above 22.6 (4.7) Terminals and supply connections (See Annex 1) (4.7.1) Contact to metal parts Fixed and not adjustable luminaire 22.6 (4.7.2) Test 8 mm live conductor Test 8 mm earth conductor 22.6 (4.7.3) Terminals for supply conductors Screw connection 22.6 ( ) Welded connections: - stranded or solid conductor See above - spot welding See above - welding between wires See above - Type Z attachment See above - mechanical test according to See above - electrical test according to 15.9 See above - heat test according to and See above 22.6 (4.7.4) Terminals other than supply connection (See Annex 1) 22.6 (4.7.5) Heat-resistant wiring/sleeves No item 22.6 (4.7.6) Multi-pole plug No item - test at 30 N See above 22.6 (4.8) Switches: adequate rating No item - adequate fixing See above - polarized supply See above - compliance with for electronic switches See above 22.6 (4.9) Insulating lining and sleeves (4.9.1) Retainement No item Method of fixing... : See above

9 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 9 of (4.9.2) Insulated linings and sleeves --- Resistant to a temperature > 20 C to the wire temperature or No item a) & c) Insulation resistance and electric strength See above b) Ageing test. Temperature (C)... : See above 22.6 (4.10) Insulation of Class II luminaires (luminaire class III, electronic ballast class II) (4.10.1) No contact, mounting surface accessible metal parts wiring of basic insulation Safe installation fixed luminaires Capacitors and switches No item Interference suppression capacitors according to IEC No item 22.6 (4.10.2) Assembly gaps: not coincidental - no straight access with test probe 22.6 (4.10.3) Retainment of insulation: fixed Fixed with 2 screws - unable to be replaced; luminaire inoperative No possible incorrect replacement - sleeves retained in position No item - lining in lampholder No item 22.6 (4.11) Electrical connections (4.11.1) Contact pressure 22.6 (4.11.2) Screws: self-tapping screws No item - thread-cutting screws No item 22.6 (4.11.3) Screw locking: spring washer No item - rivets No item 22.6 (4.11.4) Material of current-carrying parts Brass > 50% copper 22.6 (4.11.5) No contact to wood or mounting surface 22.6 (4.11.6) Electro-mechanical contact systems

10 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 10 of (4.12) Mechanical connections and glands 22.6 (4.12.1) Screws not made of soft metal Screws of insulating material Metallic Torque test: torque (Nm); part qccess suplly wires connection... : Torque test: torque (Nm); screws for lamp change 3,9mm... : 0,5 Nm 1,2Nm Torque test: torque (Nm); part... : (4.12.2) Screws with diameter < 3 mm screwed into metal Screw diameter 2,9mm 22.6 (4.12.4) Locked connections: - fixed arms; torque (Nm)... : No item - lampholder; torque (Nm)... : No item - push-button switches; torque 0,8 Nm... : No item 22.6 (4.12.5) Screwed glands; force (Nm)... : Moulded 6, (4.13) Mechanical strength (4.13.1) Impact tests: - fragile parts; energy (Nm)... : other parts; energy (Nm)... : 0,35 1) live parts 2) linings 3) protection 4) covers 22.6 (4.13.3) Straight test finger 22.6 (4.13.4) Rough service luminaires I54 or higher No for rough service a) fixed See above b) hand-held See above c) delivered with a stand See above d) for temporary installations and suitable for mounting on a stand See above 22.6 (4.13.6) Tumbling barrel No plug-ballast/transformer

11 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 11 of (4.14) Suspensions and adjusting devices, no item (4.14.1) Mechanical load:, A) four times the weight See above B) torque 2,5 Nm See above C) bracket arm; bending moment (Nm)...: ---, see above D) load track-mounted luminaires See above E) clip-mounted luminaires, glass-shelve. Thickness (mm)... : ---, see above Metal rod. diameter (mm)... : ---, see above Fixed luminaire or independent control gear without fixing devices See above 22.6 (4.14.2) Load to flexible cables, no item Mass (kg)... : ---, see above Stress in conductors (N/mm²)... : ---, see above Mass (kg) of semi-luminaire... : ---, see above Bending moment (Nm) of semi-luminaire... : ---, see above 22.6 (4.14.3) Adjusting devices:, no item - flexing test; number of cycles... : ---, see above - strands broken See above - electric strength test afterwards See above 22.6 (4.14.4) Telescopic tubes: cords not fixed to tube; no strain on conductors No item 22.6 (4.14.5) Guide pulleys No item 22.6 (4.14.6) Strain on socket-outlets No item 22.6 (4.15) Flammable materials: - glow-wire test 650 C See clause spacing 30 mm See above - screen withstanding test of See above - screen dimensions See above - no fiercely burning material See above - thermal protection See above - electronic circuits exempted See above

12 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 12 of (4.15.2) Luminaires made of thermoplastic material with lamp control gear --- a) construction b) temperature sensing control See clause c) surface temperature 22.6 (4.16) Luminaires for mounting on normally flammable surfaces --- No lamp control gear Electronic control device 22.6 (4.16.1) Lamp control gear spacing: spacing 35 mm See above - spacing 10 mm See above 22.6 (4.16.2) Thermal protection: in lamp control gear See above - external See above - fixed position See above - temperature marked lamp control gear See above 22.6 (4.16.3) Design to satisfy the test of 12.6 See above 22.6 (4.17) Drain holes No drain hole Clearance at least 5 mm See above 22.6 (4.18) Resistance to corrosion:, Thermoplastic enclosure (4.18.1) - rust-resistance See above 22.6 (4.18.2) - season cracking in copper See above 22.6 (4.18.3) - corrosion of aluminium See above 22.6 (4.19) Ignitors compatible with ballast No ítem 22.6 (4.20) Rough service vibration No for rough service 22.6 (4.21) rotective shield:, no item 22.6 (4.21.1) Shield fitted See above Shield of glass if tungsten halogen lamps See above 22.6 (4.21.2) articles from a shattering lamp not impair safety See above 22.6 (4.21.3) No direct path See above 22.6 (4.21.4) Impact test on shield See above Glow-wire test on lamp compartment See above 22.6 (4.22) Attachments to lamps No ítem

13 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 13 of (4.23) Semi-luminaires comply Class II No semiluminaire 22.6 (4.24) UV radiation for tungsten halogen lamps and metal halide lamps (Annex ) Fluorescent 22.6 (4.25) No sharp point or edges 22.6 (4.26) Short-circuit protection:, no SELV parts 22.6 (4.26.1) Uninsulated accessible SELV parts See above 22.6 (4.26.2) Short-circuit test See above 22.6 (4.26.3) Test chain according to Figure 29 See above (-) No glow starters in circuit in start of or during the emergency mode (-) Lamp control gears According to IEC , see applicable requirements (-) Failure of one luminaire not affect other (-) Circuit separation (self-contained lum.) Centrally supplied luminaire (-) Circuit separation (centrally supplied lum.) No combined luminaire (-) Charging device Centrally supplied luminaire Indicator lamp and colour See above (-) Battery requirements Centrally supplied luminaire (-) Safety device Centrally supplied luminaire (-) No switch Centrally supplied luminaire (-) Failure of lamp(s) Centrally supplied luminaire (-) Current limiting device Centrally supplied luminaire (-) Influence in emergency mode Centrally supplied luminaire (-) Changing device Centrally supplied luminaire (-) Influence on luminaire with remote inhibiting facility Centrally supplied luminaire (-) Operation of remote control Centrally supplied luminaire (-) Influence on luminaire with rest mode facility Centrally supplied luminaire (-) Current drain Centrally supplied luminaire (-) Lamp voltage Centrally supplied luminaire

14 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 14 of (11) CREEAGE DISTANCES AND CLEARANCES --- Working voltage (V)... : 230VAC Voltage form Sinusoidal Non-sinusoidal TI < 600 > 600 Impulse withstand category (Normal category II) Category II (Category III Annex U) Rated pulse voltage (kv)...: --- (1) Current-carrying parts of different polarity: cr (mm); cl (mm)...: (2) Current-carrying parts and accessible parts: cr (mm); cl (mm)...: To earth terminal (class II luminaire) To accessible parts (class II luminaire) To accessible parts in lamp change (basic insul.) (3) arts becoming live due to breakdown of basic insulation and metal parts: Mea: cr >3,3; cl >3,3 Min: cr 2,5; cl 1,5 Category III cr(mea:5,5 / min.5) cl(mea:5,5 / min:3) cr(mea: :>6,5 / min:5) cl(mea:>6,5 / min:3) cr(mea:>3,3 / min:2,5) cl(mea:>3,3 / min:1,5) No metal parts cr (mm); cl (mm)...: (4) Outer surface of cable where it is clamped and No metal parts metal parts: cr (mm); cl (mm)...: (5) Not used (6) Current-carrying parts and supporting surface: cr (mm); cl (mm)... : cr(mea: :>6,5 / min:5) cl(mea:>6,5 / min:3) 22.8 (7) ROVISION FOR EARTHING ( ) Accessible metal parts Class II luminaire Metal parts in contact with supporting surface See above Resistance < 0,5 See above Self-tapping screws used See above Thread-forming screws See above Thread-forming screw used in a grove See above Earth makes contact first See above 22.8 ( ) Earth continuity in joints etc. Class II luminaire 22.8 (7.2.4) Locking of clamping means See above

15 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 15 of 52 Compliance with See above Terminal blocks with integrated screwless earthing contacts tested according Annex V See above 22.8 (7.2.5) Earth terminal integral part of connector socket Class II luminaire 22.8 (7.2.6) Earth terminal adjacent to mains terminals Class II luminaire 22.8 (7.2.7) Electrolytic corrosion of the earth terminal Class II luminaire 22.8 (7.2.8) Material of earth terminal Class II luminaire Contact surface bare metal See above 22.8 (7.2.10) Class II luminaire for looping-in Double or reinforced insulation to functional earth 22.8 (7.2.11) Earthing core coloured green-yellow Class II luminaire Length of earth conductor See above 22.9 (14) SCREW TERMILS --- Separately approved; component list (see Annex 1) art of the luminaire (see Annex 3) 22.9 (15) SCREWLESS TERMILS AND ELECTRICAL CONNECTIONS Separately approved; component list (see Annex 1) art of the luminaire (see Annex 4) (5) EXTERL AND INTERL WIRING (5.2) Supply connection and external wiring (5.2.1) Means of connection...: Terminals (5.2.2) Type of cable...: ---, not provided Nominal cross-sectional area (mm²)...: --- Cables equal to IEC or IEC (5.2.3) Type of attachment, X, Y or Z (5.2.5) Type Z not connected to screws (5.2.6) Cable entries: suitable for introduction Gland - adequate degree of protection See above

16 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 16 of (5.2.7) Cable entries through rigid material have rounded edges (5.2.8) Insulating bushings:, no metal parts suitably fixed See above - material in bushings See above - material not likely to deteriorate See above - tubes or guards made of insulating material See above (5.2.9) Locking of screwed bushings See above (5.2.10) Cord anchorage: Gland covering protected from abrasion - clear how to be effective - no mechanical or thermal stress - no tying of cables into knots etc. - insulating material or lining ( ) Cord anchorage for type X attachment: --- a) at least one part fixed b) types of cable c) no damaging of the cable d) whole cable can be mounted e) no touching of clamping screws f) metal screw not directly on cable No metal screw g) replacement without special tool Glands not used as anchorage Suitable for recommended type of cables Labyrinth type anchorages No item ( ) Adequate cord anchorage for type Y and type Z attachment ( ) Tests: impossible to push cable; unsafe - pull test: 25 times; pull (N)... : 60 - torque test: torque (Nm)... : 0,25 - displacement 2 mm <1,4mm

17 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 17 of 52 - no movement of conductors - no damage of cable or cord (5.2.11) External wiring passing into luminaire No other than supply (5.2.12) Looping-in terminals Ground terminal (5.2.13) Wire ends not tinned Wire ends tinned: no cold flow See above (5.2.14) Mains plug same protection No plug Class III luminaire plug See above (5.2.16) Appliance inlets (IEC 60320) No inlet Appliance couplers of class II type See above (5.2.17) No standardized interconnecting cables properly assembled No interconnecting cables (5.2.18) Used plug in accordance with - IEC No plug - other standard See above (5.3) Internal wiring (5.3.1) Internal wiring of suitable size and type No internal wiring used other than supply --- Through wiring not delivered/ mounting instruction See above - factory assembled See above - socket outlet loaded (A)... : See above - temperatures... : (see Annex 2), see above Green-yellow for earth only See above ( ) Internal wiring connected directly to fixed wiring --- Cross-sectional area (mm²)... : See above Insulation thickness See above Extra insulation added where necessary See above ( ) Internal wiring connected to fixed wiring via internal current-limiting device --- Adequate cross-sectional area and insulation thickness See above ( ) Double or reinforced insulation for class II See above ( ) Conductors without insulation See above

18 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 18 of ( ) SELV current-carrying parts See above ( ) Insulation thickness other than VC or rubber See above (5.3.2) Sharp edges etc. See above --- No moving parts of switches etc. See above Joints, raising/lowering devices See above Telescopic tubes etc. See above No twisting over 360 See above (5.3.3) Insulating bushings: suitable fixed See above - material in bushings See above - material not likely to deteriorate See above - cables with protective sheath See above (5.3.4) Joints and junctions effectively insulated See above (5.3.5) Strain on internal wiring See above (5.3.6) Wire carriers See above (5.3.7) Wire ends not tinned See above Wire ends tinned: no cold flow See above (-) ermanently connected See above (8) ROTECTION AGAINST ELECTRIC SHOCK (8.2.1) Live parts not accessible with standard test finger Basic insulated parts not used on the outer surface without appropriate protection Basic insulated parts not accessible with standard test finger on portable and adjustable luminaires Basic insulated parts not accessible with Ø 50 mm probe from outside, within arms reach, on wallmounted luminaires Lamp and starterholders in portable and adjustable luminaires comply with double or reinforced insulation requirements Basic insulation only accessible under lamp or starter replacement rotection in any position Double or reinforced insulation See above See above Fixed luminaire In Lamp replacement

19 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 19 of 52 Double-ended tungsten filament lamp Fluorescent lamp Insulation lacquer not reliable Not used Double-ended high pressure discharge lamp Fluorescent lamp Relevant warning according to fitted to the luminaire (8.2.2) ortable luminaire adjusted in most unfavourable position Fluorescent lamp Fixed (8.2.3.a) Class II luminaire: basic insulated metal parts not accessible during starter or lamp replacement - basic insulation not accessible other than during starter or lamp replacement - glass protective shields not used as supplementary insulation (8.2.3.b) BC lampholder of metal in class I luminaires shall be earthed No metal parts No glass (8.2.3.c) Class III luminaires with exposed SELV parts: class II luminaire --- Ordinary luminaire: touch current...: See above - no-load voltage...: See above Other than ordinary luminaire: nominal voltage...: See above (8.2.4) ortable luminaire: fixed luminaire protection independent of supporting surface See above - terminal block completely covered See above (8.2.5) Compliance with the standard test finger or relevant probe (8.2.6) Covers reliably secured (8.2.7) Discharging of capacitors 0,5 F <0,1 F --- ortable plug connected luminaire with capacitor See above Other plug connected luminaire with capacitor See above Discharge device on or within capacitor See above Discharge device mounted separately See above

20 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 20 of (12) ENDURANCE TEST AND THERMAL TEST (12.3) Endurance test: - mounting-position...: Under ceiling - test temperature (C)...: 35 - total duration (h)...: supply voltage: Un factor; calculated voltage (V) : 1,1 230=253 - lamp used...: F8T5 8W (12.3.2) After endurance test: no part unserviceable - luminaire not unsafe - no damage to track system No track system fixation - marking legible - no cracks, deformation etc (12.4) Thermal test (normal operation) (see Annex 2) (12.5) Thermal test (abnormal operation) (see Annex 2) (12.6) Thermal test (failed lamp control gear condition): (12.6.1) Through wiring or looping-in wiring loaded by a current of (A)... : - case of abnormal conditions... : electronic lamp control gear Yes - measured winding temperature (C): at 1,1 Un. : measured mounting surface temperature (C) at 1,1 Un... : electronic lamp control gear - calculated mounting surface temperature (C)...: See above - track-mounted luminaires See above (12.6.2) Temperature sensing control - case of abnormal conditions...: Electronic control gear - thermal link See above - manual reset cut-out See above - auto reset cut-out See above - measured mounting surface temperature (C)...: See above - track-mounted luminaires See above

21 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 21 of (12.7) Thermal test (failed lamp control gear in plastic luminaires): (12.7.1) Luminaire without temperature sensing control ( ) Luminaire with fluorescent lamp 70W (electronic control device, fluorescent 8W, not apply these requirements Test method or Annex V...: --- Test according to : - case of abnormal conditions - Ballast failure at supply voltage (V)...: Components retained in place after the test - Test with standard test finger after the test Test according to Annex V: case of abnormal conditions - measured winding temperature (C): at 1,1 Un..: - measured temperature of fixing point/exposed part (C): at 1,1 Un... : - calculated temperature of fixing point/exposed part (C)... : --- Ball-pressure test: - part tested; temperature (C)... : - part tested; temperature (C)... : ( ) Luminaire with discharge lamp, fluorescent lamp > 70W, transformer > 10 VA (fluorescent lamp 8W) - case of abnormal conditions - measured winding temperature (C): at 1,1 Un.. : measured temperature of fixing point/exposed part (C): at 1,1 Un... : - calculated temperature of fixing point/exposed part (C)... : Ball-pressure test: - part tested; temperature (C)...: part tested; temperature (C)...: ( ) Luminaire with short circuit proof transformers 10 VA (fluorescent lamp 8W) - case of abnormal conditions

22 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 22 of 52 - Components retained in place after the test - Test with standard test finger after the test (12.7.2) Luminaire with temperature sensing control - thermal link Yes No - manual reset cut-out Yes No - auto reset cut-out Yes No - case of abnormal conditions - highest measured temperature of fixing point/exposed part (C):... : --- Ball-pressure test: - part tested; temperature (C)...: part tested; temperature (C)...: (-) Emergency mode to (see Annex 2) (-) Additional thermal test (see Annex 2) (-) Rated lumen output (9) RESISTANCE TO DUST, SOLID OBJECTS AND MOISTURE (9.2) Tests for ingress of dust, solid objects and moisture: - classification according to I...: I65 - mounting position during test...: Fixed to wall - fixing screws tightened; torque (Nm)...: 0,8 - tests according to clauses...: and electric strength test afterwards a) no deposit in dust-proof luminaire I6X b) no talcum in dust-tight luminaire c) no trace of water on current-carrying parts or SELV parts or where it could become a hazard d) i) For luminaires without drain holes no water entry d) ii) For luminaires with drain holes no hazardous water entry No drain holes e) no water in watertight luminaire No watertight luminaire f) no contact with live parts (I 2X) I6X

23 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 23 of 52 f) no entry into enclosure (I 3X and I 4X) I6X f) no contact with live parts (I3X and I4X) I6X g) no trace of water on part of lamp requiring protection from splashing water h) no damage of protective shield or glass envelope No glass (9.3) Humidity test 48 h 25ºC 93% (10) INSULATION RESISTANCE AND ELECTRIC STRENGTH (10.2.1) Insulation resistance test Cable or cord covered by metal foil or replaced by a metal rod of mm Ø... : Insulation resistance (M) SELV: between current-carrying parts of different polarity... : - between current-carrying parts and mounting surface... : - between current-carrying parts and metal parts of the luminaire... : Other than SELV: No SELV parts See above See above - between live parts of different polarity... : L/N connected to rectifier bridge - between live parts and mounting surface... : >10 3 MΩ (min. 4 MΩ) - between live parts and metal parts... : Enclosure covered by metal foil, >10 3 MΩ (min. 4 MΩ) - between live parts of different polarity through action of a switch... : No switch (10.2.2) Electric strength test --- Dummy lamp No ignitor Luminaires with ignitors after 24 h test No ignitor Luminaires with manual ignitors No ignitor

24 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 24 of 52 Test voltage (V): 1460V (basic insulation) 2920V (reinforced or doublé insulation) SELV: between current-carrying parts of different polarity... : - between current-carrying parts and mounting surface... : - between current-carrying parts and metal parts of the luminaire... : Other than SELV: No SELV parts See above See above - between live parts of different polarity... : L/N connected to rectifier bridge - between live parts and mounting surface... : Double insulation - between live parts and metal parts... : Enclosure covered by metal Double insulation - between live parts of different polarity through action of a switch... : No switch (10.3) Touch current (ma)... : <0,1mA (max: 0,5mA) (13) RESISTANCE TO HEAT, FIRE AND TRACKING (13.2.1) Ball-pressure test: Enclosure, base and intermediate cover; 75 (C) : <1,4mm - Enclosure, difusser; 75 (C)...: <1,4mm - Enclosure CB support; 75 (C)...: <1,4mm (13.3.1) Needle flame test (10 s): part tested...: part tested...: (13.3.2) Glow-wire test (650C): Enclosure CB support...: No flame - Enclosure, intermediate cover...: ---

25 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 25 of (-) Glow-wire test (850C): (only for external parts) Enclosure, base... : Flame goes out immediately after removing heat source - Enclosure, difusser... : Flame goes out immediately after removing heat source - part tested... : (13.4.1) Tracking test: part tested... : CB, test at 175V (-) FUNCTIOL SAFETY (-) Rated lumen output Rated: 340 lm % of rated lumen output after 5 seconds of emergency mode 100% of rated lumen output after 60 seconds of emergency mode until end of rated time of emergency operation Emergency lighting for high risk area, 100% of rated lumen output after 0,5s of emergency mode until end of rated time of emergency operation Self contained luminaires, charge period of 24 hours at 0,9 UN MIN Emergency luminaire supplied by central source, supplied at 0,85 U N MIN, measurements after thermal stabilization Measured:---, no self contained luminaire Measured after stabilization, centrally supplied luminaire Measured:--- No for high risk area Vcharge=---V V=195,5 Vac Lumen output measurement Reference lamp measurement I COR (lx) I MEDIDA (lx) ASIGDO (lm) 161,7 550, Mode Measured Illuminance (lx) Luminous flux output (lm) MÍN rated. I COR (lm) AC supply 154, , , (-) hotometric data p (-) hotometric measurements See Annex 1 of this report p (-) Colour-rendering index Not for evacuation lighting (-) Iluminance and luminance requirements Not for safety signalling

26 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 26 of (-) CHANGEOVER OERATION (-) Changeover test No selfcontained luminaires (-) Rated lumen output See above (-) Changeover test See above Rated lumen output See above (-) HIGH TEMERATURE OERATION --- Operation at 70C Rated lumen output 50% measured value at ta after 1h 25ºC: 3950lx 70ºC(after 1h):2420lx 61,3% (-) BATTERY CHARGERS FOR SELF-CONTAINED EMERGENCY LUMIIRES (-) Charge performance No self-contained emergency luminaire (-) Compliance with IEC See above (-) TEST DEVICES FOR EMERGENCY OERATION (-) Device for simulation failure No self-contained emergency luminaire (-) Influence of remote testing device See above (-) Indication colour See above

27 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 27 of 52 ANNEX A: Batteries for emergency luminaires --- A.1 Type of batteries No battery, centrally supplied emergency luminaire --- A.2 Battery conform to relevant standard --- Luminaire operate within specific tolerances --- A.3 Battery capacity --- A.4 Sealed nickel cadmium batteries --- A.4.1 Battery conform to IEC See above A.4.2.a Ambient air temperature 50 C See above A.4.2.b Overcharge rate 0,08 C5A See above A.4.2.c Ambient temperature of the cells 5 C See above A.4.2.d Discharge rates 0,6 C5A for 1h and 0,25 C5A for 3h See above A.5 Valve regulated lead acid batteries --- A.5.1 Battery conform to relevant part of IEC or IEC See above A.5.2.a Ambient air temperature 30 C or 25 C See above A.5.2.b Recharge current 0,4 C20 See above A.5.2.c Discharge rates 0,4 C20 for 1h and 0,17 C20 for 3h See above A.5.2.d Ripple current 0,1 C20 See above A.5.2.e Ambient temperature of the cells 5 C See above A.6 Ambient temperature of the cells measured after 48 h A.7 Alternative operating parameters and evidence if operating outside limits in A.4 and A.5 See above See above A.8 Battery only replaced by a competent person See above ANNEX B: Luminaire classification --- Classified and marked according Annex B Z 0 ***** --- ANNEX C: Luminance measurements --- C.1 Contrast measurements No safety signalling C.2 On site photometric tests No safety signalling

28 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 28 of 52 ANNEX ZB DIVERGENCES A The installation of elements next to the luminaire is not allowed 22.4 Self-contained safety luminaires must be provided with a means of "sleep mode", which must be added into equipment or outside In public buildings electrical installations should only have fixed electrical accessories. Lamps for general purpose lighting and lamps for emergency lighting should be embedded in separate luminaires Minimum I degree of self-contained luminaires with fluorescent lamps should be I External parts of fixed or suspended luminaires must also withstand glow wire test at 850 C Autonomy of operation assigned to self-contained emergency luminaires used for emergency lighting must be at least one hour Minimum luminous flux output for self-contained emergency luminaires with incandescent lamps should be 30 lumen / The characteristics of the products are based only on the assigned luminous flux and, therefore, the photometric characteristics of luminaires could not be provided or verified Switching from the normal state to the state of emergency should occur when the normal power supply is less than 0.7 times the rated value France: Fire safety regulations in buildings open to the public. Clause EC 15 Spain: RD 842/2002: REBT ITC-BT-28 clause 3.4.1, no self contained luminaire Dinamarca: Regulation strong currents, sec 6 clause France: Safety regulation in public buildings. Clause EL 10, chapter 1 France: Fire safety regulations in buildings open to the public. Clause EC 5, chapter 3, only one lamp Spain: RD 842/2002: REBT ITC-BT-28 clause 3.4.1, No self-contained, I65 Francia: : Fire safety regulations in buildings open to the public Clause EC 5 chapter 2 Spain: RD 842/2002: REBT ITC-BT-28 clause and 3.1.2, No self-contained luminaire Spain: RD 842/2002: REBT ITC-BT-28 clause 3.4.1, No self-contained luminaire Francia: Fire safety regulations in buildings open to the public Clause EC9 and EC10, provided Spain:: RD 842/2002: REBT ITC-BT-28 cap. 3.1, No self-contained luminaire

29 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 29 of 52 ANNEX 1: components --- object/part No. Enclosure CB support manufacturer/ trademark LG CHEM type/model technical data standard mark(s) of conformity ABS LG AF C UL94V0 T ISO75A :81ºC Enclosure, base and middle cover Sabic C LEXAN 223R/WH 6D 257 UL94V0 T ISO75A :122ºC Enclosure, difusser Sabic C LEXAN VR1820 T ISO75A :122ºC Lampholder BJB V 2 A T130 EN VDE rinted board Nam Hing Industrial NHL-4806 UL94 V0 T max 110ºC UL94 UL E74035 Terminal block DEGSON DG V 20 A T ºC UL94V0 EN VDE Inductance Normalux IND5 2,4mH 2,6 Ω TC Vishay TCCL05H950HBE 265V 56Ω I max :600mA T140ºC Ta:-0 +70ºC Rectifier bridge Diodes HD06 600V 0,8 A T: ºC UL1434 UL E UL E95661 Gland Gaestopas M16x1,5 olyamide

30 UNE-EN :1999+A1:2003+Corr:2006+A2:2008 Test report: 13/ age 30 of 52 ANNEX 2: temperature measurements, thermal tests of Section 12 Type reference... : Lamp used... : Lamp control gear used... : Mounting position of luminaire... : Supply wattage (W)... : Supply current (A)... : Calculated power factor... : Table: measured temperatures corrected for ta = 25 C: - abnormal operating mode... : - test 1: rated voltage... : test 2: 1,06 times rated voltage or 1,05 times rated wattage... : - test 3: Load on wiring to socket-outlet, 1,06 times voltage or 1,05 times wattage... : - test 4: 1,1 times rated voltage or 1,05 times rated wattage... : Through wiring or looping-in wiring loaded by a current of A during the test... : 243,8V V, see abnormal test in clauses 14, 15 and 16 UNE-EN Any appreciable heating during abnormal condition of electronic control gear* temperature (C) of part Clause 12.4 normal Clause 12.5 abnormal test 1 test 2 test 3 limit test 4 limit Lampholder --- (39,3) 44, Inductance IND5 --- (51,7) 56, Supply terminals --- (40,1) 45, CB --- (50,7) 55, Enclosure CB --- (36,8) 41, Luminaire base --- (28,5) 33, Support surface --- (25,7) 30, <30* 130 Difusser --- (30,0) 35, Supply wire --- (35,5) 40, Ambient temperature --- (20,0) 25,

31 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 31 of 52 4 (4) GENERAL REQUIREMENTS Annex J applicable... Yes No Compliance of independent controlgear enclosure with EN Test with luminaire enclosure according EN (6) CLASSIFICATION Independent controlgear... Yes No Built-in starting controlgear... Yes No Integral starting controlgear... Yes No 7 MARKING 7.1 (7.1) Mandatory markings (other than integral ballasts): Integral ballast (10) ROTECTION AGAINST ACCIDENTAL CONTACT WITH LIVE ARTS (10.1) Starting device protected against accidental contact with live parts Device protected by luminaire enclosure, see tests according EN (8) TERMILS --- Separately approved, component list (see Annex ) Screw terminals: compliance with Section 14 of IEC Screwless terminals: compliance with Section 15 of IEC See above See above 10 (9) ROVISION FOR EARTHING --- Terminal complying with clause 8 in art 1 Locked against loosening and not possible to loosen by hand Not possible to loosen clamping means unintentionally on screwless terminals Only for interconnection, terminal certified Class II, see test in section EN See above Earthing via means of fixing See above Earthing terminal only used for the earthing of the control gear All parts of material minimizing the danger of electrolytic corrosion See above See above Made of brass or equivalent material See above

32 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 32 of 52 Contact surface bare metal See above Earth contact via the track on the printed board --- Test with a current of 25 A between earthing See above terminal and the accessible metal parts; measured resistance (): < 0, (11) MOISTURE RESISTANCE AND INSULATION (see tests in conjunction with clause 10.2 EN ) After storage 48 h at 91-95% relative humidity and C measuring of insulation resistance with d.c. 500 V (M): For basic insulation 2 M... For double or reinforced insulation 4 M... The leakage current shall not exceed the High frequency leakage current values shown in figure 2 when measured in Measured: 0,3mA accordance with annex I... (Max: 85mA for f>50khz) (12) ELECTRIC STRENGTH (see tests in conjunction with clause 10.2 EN ) --- Immediately after clause 11 electric strength test for 1 min Working voltage 42 V, test voltage 500 V Working voltage > 42 V 1000 V, test voltage (V): --- Basic insulation, 2U V Supplementary insulation, 2U V Double or reinforced insulation, 4U V No flashover or breakdown 14 (14) FAULT CONDITIONS --- When operated under fault conditions the controlgear: does not emit flames or molten material - does not produce flammable gases - protection against accidental contact not impaired Thermally protected ballasts does not exceed the marked temperature value Fault conditions: capacitors, resistors or inductors without proof of compliance with relevant specifications have been shortcircuited or disconnected (see appended table)

33 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 33 of 52 - (14.1) Short-circuit of creepage distances and clearances if less than specified in clause 16 in art 1 (except between live parts and accessible metal parts) Creepage distances on printed boards less than specified in clause 16 in art 1 provided with coating according to IEC (14.2) Short-circuit or interruption of semiconductor devices - (14.3) Short-circuit across insulation consisting of lacquer, enamel or textile (see appended table) (see appended table) (see appended table) - (14.4) Short-circuit across electrolytic capacitors (see appended table) - (14.5) After the tests has been carried out on three samples: --- The insulation resistance 1 M No flammable gases No accessible parts have become live During the tests, a five-layer tissue paper, where the test specimen is wrapped, does not ignite - (14.6) Relevant fault condition tests with high-power supply Tested inside luminaire enclosure 15 ROTECTION OF ASSOCIATED COMONENTS Voltage at the output terminals does at no time exceed the maximum permitted peak value specified in table Voltage at the output terminals does not exceed the maximum working voltage for which the ballast is declared 15.3 Voltage at the output terminals does not exceed the maximum value for which the ballast is designed: (see appended table) (see appended table) (see appended table) - for a period longer than 30 s after switch on - or at the beginning of the starting process - duration of working voltage does not exceed 30 s 15.4 Voltages measured in 15.1, 15.2 and 15.3 between any output terminal and earth

34 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 34 of 52 Voltages present across insulation barriers within associated components measured 15.5 For controllable ballasts: the control input isolated from the mains circuit by basic insulation, or - if SELV, double or reinforced insulation is provided No controllable See above 16 ABNORMAL CONDITIONS --- Safety not impaired when ballast is operated at any voltage between 90% and 110% of rated voltage (see appended table) The following condition(s) was/were applied for 1 h: a) one lamp not inserted b) broken cathodes c) deactivated lamp d) rectifying effect (figure 1); R () e) short-circuit of starter switch, if any No item No defect impairing safety Maximum measured current in any falult <1mA, no heating produced No smoke produced See above 17 BEHAVIOUR OF THE BALLAST AT END OF LAM LIFE End of lamp life effects --- At the end of lamp life the ballast shall behave in such a way that no overheating of lamp cap(s) occurs at any voltage between 90% and 110% of the rated supply voltage Method clause Asymmetric pulse test --- Adequate protection to prevent lamp cap overheating at the end of the lamp life cycle See clause for 13 mm (T4) lamps, max = 5,0 W for 16 mm (T5) lamps, max = 7,5 W

35 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 35 of Asymmetric power test --- Adequate protection to prevent lamp cap overheating at the end of the lamp life cycle - for 13 mm (T4) lamps, max = 5,0 W... T5 cap - for 16 mm (T5) lamps, max = 7,5 W... max = 1,9W 17.4 Open filament test Adequate protection to prevent lamp cap overheating at the end of the lamp life cycle under filament conditions See clause for 13 mm (T4) lamps, I max = 1 ma for 16 mm (T5) lamps, I max = 1,5 ma Test procedure used (A or B) (16) CREEAGE DISTANCES AND CLEARANCES --- Creepage distances and clearances according to Table 3 and 4, as appropriate (see appended table) --- rinted boards see clause 14 of IEC See measurements in conjunction with clause 22.7 IEC Insulating lining of metallic enclosures No enclosure 20 (17) SCREWS, CURRENT-CARRYING ARTS AND CONNECTIONS --- Screws, current-carrying parts and connections in compliance with IEC (No screws present in ballast) 21 (18) RESISTANCE TO HEAT, FIRE AND TRACKING (18.1) arts of insulating material retaining live parts in position, ball-pressure test: - part; test temperature (C)... CB, see clause IEC part; test temperature (C) (18.2) rinted boards in accordance with 8.7 of IEC and relevant parts of IEC (18.3) External parts of insulating material preventing electric shock glow-wire test 650 C CB certified UL94 V0 (see component list) No enclosure, provided by luminaire

36 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 36 of 52 - (18.4) arts of insulating material retaining live parts in position, needle-flame test 10 s: flame extinguished within 30 s No other ítem than CB - no flaming drops igniting tissue paper No other ítem than CB - (18.5) Tracking test according section 13 of IEC if required See test in clause IEC (19) RESISTANCE TO CORROSION -- Applicable parts comply with of No metallic parts IEC Adequate varnish on the outer surface See above - (20) NO-LOAD OUTUT VOLTAGE --- No load output voltage not differ more than 10 % from rated voltage Integral ballast, output voltage not marked 14 TABLE: tests of fault conditions art Simulated fault Hazard Capacitor C16 Shortcircuit, I<10mA NO Capacitor C16 Open circuit, I<10mA NO Capacitor C13 Shortcircuit, I=60mA NO Capacitor C13 Open circuit, I<10mA NO Mosfet M1 Shortcircuit G-D, I<10mA NO Mosfet M1 Shortcircuit D-S, I<10mA NO Mosfet M2 Shortcircuit G-D, I<10mA NO Mosfet M2 Shortcircuit D-S, I<10mA NO R1 Shortcircuit (rotection RF1 t<1s, I>3A) NO Lamp Not inserted, I<10mA NO Lamp Broken cathodes, I<10mA NO Lamp Deactivated lamp, I<10mA NO Lamp Rectifying effect, I<10mA NO

37 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 37 of TABLE: protection of associated components Ballast type... Electronic hig frequency Declared working voltage V (V max: 2200V) 15.1 Dummy cathode resistor () terminal with dummy cathode test voltage (V) 253V 50Hz output voltage (V ) A 693V output voltage (V ) B 90V output voltage (V ) C 239V 16.a The lamp or one of the lamps is not inserted terminal Open-circuit test voltage (V) 253V 50Hz output voltage (V ) A 164V output voltage (V ) B 132V output voltage (V ) C 212V 16.b The lamp does not start because one of the cathode is broken terminal broken cathode broken cathode broken cathode terminal / rectifier A B C test voltage (V) 253V 50Hz 253V 50Hz 253V 50Hz output voltage (V ) A output voltage (V ) B output voltage (V ) C c The lamp does not start although the cathode circuits are intact (resistor 36) terminal de-activated lamp test voltage (V) 253V 50Hz output voltage (V ) A 568V output voltage (V ) B 228V output voltage (V ) C 252V

38 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 38 of d The lamp operates, but one of the cathodes is de-activated or broken Cathode resistor ()... : 80 terminal rectifying effect rectifying effect terminal / rectifier resistor to lamp lamp to resistor test voltage (V) 253V 50Hz 253V 50Hz output voltage (V ) A output voltage (V ) B output voltage (V ) C Declared working voltage (V) V 16.a The lamp or one of the lamps is not inserted Test periode (s)... >0,1 terminal open-circuit test voltage (V) 253V 50Hz output voltage (V rms ) A 164 output voltage (V rms ) B 132 output voltage (V rms ) C b The lamp does not start because one of the cathode is broken Test periode (s)... >0,1 terminal / rectifier A B C test voltage (V) 253V 50Hz 253V 50Hz 253V 50Hz output voltage (V ) A output voltage (V ) B output voltage (V ) C c The lamp does not start although the cathode circuits are intact Test periode (s)... >0,1 terminal de-activated lamp test voltage (V) 253V 50Hz output voltage (V rms ) A 172 output voltage (V rms ) B 204 output voltage (V rms ) C 204

39 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 39 of Declared working voltage (V) V Test periode (s)... >0,1 Cathode resistor () d The lamp operates, but one of the cathodes is de-activated or broken terminal rectifying effect rectifying effect terminal / rectifier resistor to lamp lamp to resistor test voltage (V) 253V 50Hz 253V 50Hz output voltage (V rms ) A output voltage (V rms ) B output voltage (V rms ) C (16) TABLE: creepage distances and clearances (see measurements in clause 22.7 UNE EN ) Minimum distances for a.c. (50/60 Hz) sinusoidal voltages RMS working voltage (V) not exceeding ) minimum distances between live parts of different polarity. Specify the value measured. 2) minimum distances between live parts and accessible parts which are permanently fixed to the ballast, including screws or devices for fixing covers or fixing the ballast to its support. Specify the value measured. - required creepage distances (mm), insulation TI required creepage distances (mm), insulation TI < ,6 1,4 1, ,5 1,2 1,6 2, required clearances (mm) 0,2 1,4 1, ,5 3) minimum distances between live parts and a flat supporting surface or a loose metal cover, if any, if the construction does not ensure that the values under 2 above are maintained under the most unfavourable circumstances required clearances (mm) 2 3,2 3,6 4,8 6 8

40 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 40 of 52 Minimum distances for non-sinusoidal pulse voltages (no pulse voltages) --- rated pulse voltage (peak kv) 2,0 2,5 3,0 4,0 5,0 6,0 8,0 required minimum distances, clearances (mm) 1,0 1, ,5 8 Specify the value measured rated pulse voltage (peak kv) required minimum distances, clearances (mm) Specify the value measured rated pulse voltage (peak kv) required minimum distances, clearances (mm) Specify the value measured C ANNEX C ARTICULAR REQUIREMENTS FOR ELECTRONIC LAM CONTROLGEAR WITH MEANS OF ROTECTION AGAINST OVERHEATING ----

41 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 41 of 52 J (-) J.3 MARKING ANNEX J IN THIS ART 2 ARTICULAR REQUIREMENTS FOR A.C., A.C./D.C. or D.C. SULIED BALLASTS FOR EMERGENCY LIGHTING J.3.1 Mandatory markings: ballast is integral part of the luminaire J.4 GENERAL Satisfactory starting of lamps at 90% and 110% rated emergency power supply voltage The lamps starts and operates across the widest rated voltage range 230Vac J.5 STARTING CONDITIONS (see also tables) --- The provision of clause 7 of IEC applies at 90% and 110% of the rated emergency power supply voltage. If declared for lower temperatures than 10 C at lowest declared temperature and 90% of rated voltage. (Declared luminaire ta:25ºc) - (7.1) Conditions for ballasts with preheating (ballast without preheating) - (7.2) Conditions for ballasts without preheating: : (HF ballast, applied in conjunction with Annex D EN 60929) Glow discharge period 100 ms Glow discharge period finished when lamp current is 80 % of rated lamp current - (7.2.1) Open-circuit voltage Not defined in IEC for F8T5 8W without preheating - (7.2.2) Ballasts impedance test Not defined in IEC for F8T5 8W without preheating - (7.2.3) Cathode current Not defined in IEC for F8T5 8W without preheating - (7.3) Starting aid and distances: --- open circuit voltage during preheat and starting Without preheating voltage to starting aid See above

42 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 42 of 52 J.5 TABLES - (7.2) Conditions for ballasts without preheating U (Vac) Glow discharge period Lamp current when glow discharge period finished ,4 ms 86% ,4 ms 87% - (7.2.1) Open circuit voltage; a.c. / d.c. --- fr (Hz) Ur (V) Uoc (V) ûoc (V) R () Remarks ,3 692,5 80 f signal (Hz) 94,9 khz. Not defined in IEC for F8T5 8W without preheating ,9 478,0 80 f signal (Hz) 93,5 khz. Not defined in IEC for F8T5 8W without preheating - (7.2.2) Ballast impedance test; a.c. / d.c., (Not defined in IEC for F8T5 8W without preheating) Ta ( C) fr (Hz) Ur (V) IL (A) RL () Remarks (7.2.3) Cathode current; a.c. / d.c. (Not defined in IEC for F8T5 8W without preheating) Ta ( C) fr (Hz) Ur1 (V) I M1 (A) I M2 (A) R () Remarks J.6 OERATION CONDITIONS (see also table) --- Measured at a.c. / d.c. (Lamp control gear integral part of emergency luminaire) - (8.1) Ballast lumen factor; not less than 95 % of the value declared by the manufacturer or not less than 0,95 - (8.2) Total circuit power; not more than 110 % of the value declared by the manufacturer See above See above - (8.3) Requirements for dimming: (No dimming) -- - (8.3.1) Lamp cathode heating: The ballast provides cathode heating continuously to the lamp(s) at any dimming position See above - (8.3.2) Lamp power control: (see Annex E), See above

43 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 43 of 52 - (8.4) Ballast limiting the lamp current to a value not exceeding 115 % of that delivered to the same lamp when operated with a reference ballast I lamp max: 0,180 A According to IEC for F8T5 8W at high frecuency, not defined without preheating Supply Measured I lamp (ma) Limit (ma) 253 V AC 132, V AC 118,4 207 J.7 CURRENT --- At the rated operating voltage, the supply current not differ by more than +/-15% from the declared value. Lamp control gear integral part of emergency luminaire J.6 ANNEX E of IEC (normative) - Control interface for controllable ballasts J.8 MAXIMUM CURRENT IN ANY LEAD TO A CATHODE --- The provision of clause 11 of IEC apply at 90% and 110% of the rated emergency power supply voltage. (See table) J.8 TABLE --- Maximum current in any lead to a cathode; a.c. / d.c. Un (V) I CAT A (ma) I CAT B (ma) I CAT C (ma) --- (ma) --- (ma) --- (ma) --- (ma) --- (ma) 253 (ac) 132,4 35,9 141, (ac) 118,4 36,9 129,

44 UNE-EN :2002+Corr:2003+A1:2006+A2:2006+Corr:2011* Test report: 13/ age 44 of 52 J.9 LAM OERATING CURRENT WAVEFORM (12.2) Lamp operating current waveform --- a) for a.c. supplied control gear the enveloping wave of the lamp current does not differ by more than 4 % b) the maximum ratio of peak value to r.m.s value does not exceed 1,7 Supply I RMS (ma) I EAK (ma) RATIO EAK/RMS F (khz) ENVELOING WAVE DIFFER 253 V AC 132,4 188,1 1,42 70,3 <3% 207 V AC 118,4 164,6 1,39 66,4 <3% J.10 MAINS TRANSIENT OVERVOLTAGES --- Not applicable (test deleted in IEC 60929:2006) --- J.11 ULSE VOLTAGE FROM CENTRAL BATTERY SYSTEMS --- Test performed with three pulses according to Table J.1 AC supply J.12 TEST FOR ABNORMAL CONDITIONS --- The test of clause 16 made with ± 20% rated d.c. supply voltage J.13 TEMERATURE CYCLING TEST AND ENDURANCE TEST --- Temperature cycling test and endurance test according to IEC Cl. 26 Ballast integral part of luminaire without enclosure, thermal test according to IEC temperature cycle test, 5 cycles See above - ballast operated at tc for h... See above The lamps start and operate correctly at the end of the test See above

45 UNE-EN 50102:1996+A1:1999+Corr:2002+A1 CORR:2002 Test report: 13/ age 45 of 52 4 DESIGTIONS Code disposed IK code applied IK IK 00 Not protected IK 01 Energy 0.14 J IK 02 Energy 0.2 J IK 03 Energy 0.35 J IK 04 Energy 0.5 J IK 05 Energy 0.7 J IK 06 Energy 1 J IK 07 Energy 2 J IK 08 Energy 5 J IK 09 Energy 10 J IK 10 Energy 20 J 5 GENERAL CONDITIONS Environmental conditions according to standard New and clean enclosure articular standard requirements: Acc. To UNE EN clause Number of tested sample Mounting conditions Fixed to surface reconditioning applied None Supplied test No Mobile parts Not present Number of impacts 3 impact in weakest point ---

46 UNE-EN 50102:1996+A1:1999+Corr:2002+A1 CORR:2002 Test report: 13/ age 46 of 52 6 TEST TO VERIFY ROTECTION AGAINST IMACT DEGREE Test specified in this standard is a type test Verification by applying impacts to the tested enclosure Tests devices in clause Mounting according to manufacturer instructions Tests with rigid support 6.4 The number of impacts should be 5 in each exposed face unless the relevant product standard does not specify differently The impacts should be evenly distributed on the sides of the enclosure under test. In no case should more than 3 shocks applied in the vicinity of the same point of the envelope The particular product standard must specify the points of application of the impacts 6.5 The particular product standard should specify the criteria on which the acceptance or rejection of the shell is based As normal use --- Displacement 1 mm under IK test impacts The particular standard specifies a number of impacts 3 The particular standard specifies three hits on the point that seems weaker The particular standard specifies three hits on the point that seems weaker, difusser central point See description of the acceptance criteria of the particular standard (clause 4.13 UNE EN I Acceptance criteria: After IK There are no unacceptable damage - Safety is not affected - The reliability is not affected TEST DEVICE endular hammer acc to UNEEN : Spring hammer acc. to UNE-EN :99 Used pendular hammer Vertical hammer acc. to UNE-EN :99 Used pendular hammer ---

47 ANNEX 1 HOTOMETRIC TEST Test report: 13/ age 47 of 52 The measurements has been performed for = 5 and C= 90 (planes C0, C90, C180 and C270), with a goniophotometer of movable head operating according to recommendation of publication CIE r.º 121:1996. The measurements has been performed supplying luminaire at the voltage 0,85 U RATED,195,5V 50Hz. Initial position of fluorescent paralel to the plane plano C90-C270 DISTRIBUTION TABLE

48 ANNEX 1 HOTOMETRIC TEST Test report: 13/ age 48 of 52 OLAR DIAGRAM

49 ANNEX 2 COMONENT LIST Test report: 13/ age 49 of 52

50 ANNEX 3 ELÉCTRIC DIAGRAM Test report: 13/ age 50 of 52

51 ANNEX 4 HOTOGRAHS Test report: 13/ age 51 of 52

52 ANNEX 4 HOTOGRAHS Test report: 13/ age 52 of 52