LVD TEST REPORT. For LED TUBE. Model: T10, T8, T5. Reference No.: CE10-LIE040101S

Transcription

1 Ref. o.: CE10-LIE040101S LVD TEST REORT For LED TUBE Model: T10, T8, T5 Reference o.: CE10-LIE040101S Issued by: Shenzhen EBO Testing Center Lab location: Yihua Building, Shennan Road, Futian District, Shenzhen, ,. R. China Tel: Fax: This test report consists of 30 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by EBO. The test results in the report only apply to the tested sample. The test report shall be invalid without all the signatures of testing engineers and approver. Any objections must be raised to EBO within 15 days since the date when the report is received. It will not be taken into consideration beyond this limit. age 1 of 30

2 Ref. o.: CE10- LIE040101S LVD REORT per E :2004+A1:2006 Luminaires art 1: General requirements and tests E :1989 Luminaires, art 2: particular requirements Section one Fixed general purpose luminaires Administrative Data: Report Reference o... Tested by (name+signature)... Approved by (name+signature)... CE10- LIE040101S Adang Lu Kevin Yu Date of issue Testing Laboratory... Shenzhen EBO Testing Center Address... Testing location/ procedure... Testing location/ address... Yihua Building, Shennan Road, Futian District, Shenzhen, ,. R. China The same as above The same as above Applicant s name... :Shenzhen Saiju Electronic Co., Ltd. Address... Test specification: Standard... Test procedure... CE-LVD on-standard test method.: Test Report Form o.... 2nd. Xianshun Industrial ark, Gushu, Xixiang, Bao an, Shenzhen, Guangdong, China. E :2004+A1:2006; E :1989 /A E Test item description... :LED TUBE Trade Mark... Manufacturer... Model/Type reference... Saiju Shenzhen Saiju Electronic Co., Ltd. T10, T8, T5 General product information: 85~265V ~ 50~60Hz age 2 of 30

3 Test case does not apply to the test object : Test item does meet the requirement... : Test item does not meet the requirement : Testing (.A.) (ass) F(ail) Date of receipt of test item... : Date(s) of performance of test... : to Ref. o.: CE10-LIE040101S General remarks This report shall not be reproduced except in full without the written approval of the testing laboratory. The test results presented in this report relate only to the item tested. "(see remark #)" refers to a remark appended to the report. "(see Annex #)" refers to an annex appended to the report. Throughout this report a comma is used as the decimal separator. age 3 of 30

4 IEC and/or E Ref. o.: CE10- LIE040101S 1.2 (0) GEERAL TEST REQUIREMETS 1.2 (0.1) Information for luminaire design considered 1.2 (0.3) More sections applicable... : 1.4 (2) CLASSIFICATIO 1.4 (2.2) Type of protection... : Class Ⅰ 1.4 (2.3) Degree of protection... : I (2.4) Luminaire only suitable for non-combustible surfaces... : Luminaire suitable for normally flammable surfaces... : Luminaire suitable to be covered by insulating material.: 1.4 (2.5) Luminaire for normal use... : Luminaire for rough service... : 1.5 (3) MARKIG 1.5 (3.2) Mandatory markings Refer to marking plate osition of the marking Format of symbols/text 1.5 (3.3) Additional information Refer to marking plate Language of instructions English 1.5 (3.3.1) Combination luminaires 1.5 (3.3.2) ominal frequency in Hz 50Hz 1.5 (3.3.3) Operating temperature (3.3.4) Symbol or warning notice 1.5 (3.3.5) Wiring diagram Refer to user manual 1.5 (3.3.6) Special conditions ot applicable 1.5 (3.3.7) Metal halide lamp luminaire warning o such lamp 1.5 (3.3.8) Limitation for semi-luminaires o semi-luminaire 1.5 (3.3.9) ower factor and supply current Refer to marking 1.5 (3.3.10) 1.5 (3.3.11) 1.5 (3.3.12) 1.5 (3.3.13) Suitability for use indoors Luminaires with remote control o such structure Clip-mounted luminaire warning Fixed luminaries Specifications of protective shields o this component age 4 of 30

5 IEC and/or E (3.3.14) 1.5 (3.3.15) 1.5 (3.3.16) 1.5 (3.3.17) 1.5 (3.3.18) 1.5 ( ) Ref. o.: CE10- LIE040101S Symbol for nature of supply ~, Refer to marking Rated current of socket outlet o socket outlet Rough service luminaire o such luminaries Mounting instruction for type Y, type Z and some type X attachments Type Y on-ordinary luminaries with VC cable ot applicable Adequate warning on the package (E) 1.5 (3.4) Test with water See appended table 1.5 Test with hexane Legible after test Label attached (4) COSTRUCTIO (4.2) Components replaceable without difficulty (4.3) Wire ways smooth and free from sharp edges (4.4) Lampholders (4.4.1) Integral lampholder Approved lampholder used (4.4.2) Wiring connection (4.4.3) Lampholder for end-to-end mounting o such structure (4.4.4) ositioning - pressure test ()... o applicable - bending test (m) m (4.4.5) eak pulse voltage (4.4.6) Centre contact (4.4.7) arts in rough service luminaires resistance to tracking o rough service (4.4.8) Lamp connectors (4.4.9) Caps and bases correctly used (4.5) Starter holders Starter holder in luminaires other than class II o such component Starter holder class II construction (4.6) Terminal blocks Tails Approved terminals blocks used age 5 of 30

6 IEC and/or E Ref. o.: CE10- LIE040101S Unsecured blocks (4.7) Terminals and supply connections (4.7.1) Contact to metal parts (4.7.2) Test 8 mm live conductor Test 8 mm earth conductor (4.7.3) Terminals for supply conductors ( ) Welded connections: - stranded or solid conductor ot such connection mode - spot welding - welding between wires - Type Z attachment - mechanical test according to electrical test according to ageing test according to and (4.7.4) Terminals other than supply connection o such terminals (4.7.5) Heat-resistant wiring/sleeves o such structure (4.7.6) Multi-pole plug o plug used - test at 30 (4.8) Switches: - adequate rating o switch used - adequate fixing - polarized supply - compliance with for electronic switches (4.9) Insulating lining and sleeves (4.9.1) Retainment Used fiber-glass tube and thermal-shrinkable tube Method of fixing... : Suitably length and shrink fix (4.9.2) Insulated linings and sleeves UL approved fiber-glass tube and thermal-shrinkable tube used a) & c) Insulation resistance and electric strength b) Ageing test. Temperature ( C)... : (4.10) Insulation of Class II luminaires (4.10.1) o contact, mounting surface - accessible ClassⅠluminaire metal parts - wiring of basic insulation age 6 of 30

7 IEC and/or E (4.10.2) (4.10.3) Safe installation fixed luminaires Capacitors and switches Interference suppression capacitors according to IEC Assembly gaps: Ref. o.: CE10- LIE040101S - not coincidental - no straight access with test probe Retainment of insulation: - fixed - unable to be replaced; luminaire inoperative - sleeves retained in position - lining in lampholder (4.11) Electrical connections (4.11.1) (4.11.2) (4.11.3) (4.11.4) (4.11.5) (4.1) Contact pressure Screws: - self-tapping screws - thread-cutting screws - at least two self-tapping screws Screw locking: - spring washer - rivets Material of current-carrying parts Copper o contact to wood Electro-mechanical contact systems (4.12) Mechanical connections and glands (4.12.1) Screws not made of soft metal Screws of insulating material Torque test: torque (m); part... : Torque test: torque (m); part... : Torque test: torque (m); part... : age 7 of 30

8 IEC and/or E (4.12.2) (4.12.4) (4.12.5) Screws with diameter < 3 mm screwed into metal Locked connections: Ref. o.: CE10- LIE040101S All screws are both screwed into metal - fixed arms; torque (m)... : 5m - lampholder; torque (m) m - push-button switches; torque 0,8 m... Screwed glands; force ()... o such construction (4.13) Mechanical strength (4.13.1) (4.13.3) (4.13.4) (4.13.6) Impact tests: - fragile parts; energy (m)... - other parts; energy (m) m 1) live parts Cannot be touched 2) linings 3) protection 4) covers Straight test finger Rough service luminaires - I54 or higher ot such luminaire a) fixed b) hand-held c) delivered with a stand d) for temporary installations and suitable for mounting on a stand Tumbling barrel ot applicable (4.14) Suspensions and adjusting devices (4.14.1) Mechanical load: A) four times the weight B) torque 2,5 m... : C) bracket arm; bending moment (m)... : 1.0m, 1min D) load track-mounted luminaires E) clip-mounted luminaires, glass-shelve. Thickness (mm)... : age 8 of 30

9 IEC and/or E Ref. o.: CE10- LIE040101S (4.14.2) metal rod. Diameter (mm)... : Fixed luminaire or independent control gear without fixing devices Load to flexible cables Mass (kg)... : 0.28kg Stress in conductors (/mm²)... : o tension will not applied to the conductors Semi-luminaires mass (kg)... : ot applicable (4.14.3) (4.14.4) (4.14.5) (4.14.6) Semi-luminaires bending moment (m)... : Adjusting devices: - flexing test; number of cycles... : ot applicable - strands broken - electric strength test afterwards Telescopic tubes: cords not fixed to tube; no strain on conductors Use fiber glass tube to prevent strain Guide pulleys ot applicable Strain on socket-outlets (4.15) Flammable materials: (4.15.2) - glow-wire test 650 C See appended table spacing 30 mm - screen withstanding test of screen dimensions - no fiercely burning material - thermal protection - electronic circuits exempted Luminaires made of thermoplastic material with lamp control gear a) construction o lamp control gear b) temperature sensing control c) surface temperature (4.16) Luminaires marked with F-symbol (4.16.1) o lamp control gear See clause 12 Lamp control gear spacing: - spacing 35 mm o lamp control gear age 9 of 30

10 IEC and/or E (4.16.2) (4.16.3) Ref. o.: CE10- LIE040101S - spacing 10 mm Thermal protection: - in lamp control gear o such component - external - fixed position - temperature marked lamp control gear "F" curve measured See appended table 12.5 (4.17) Drain holes Clearance at least 5 mm o drain holes (4.18) Resistance to corrosion: (4.18.1) (4.18.2) (4.18.3) - rust-resistance I65 - season cracking in copper - corrosion of aluminium o such material (4.19) Ignitors compatible with ballast o such component (4.20) Rough service vibration o this luminaires (4.21) rotective shield: (4.21.1) (4.21.2) (4.21.3) (4.21.4) Shield fitted o tungsten halogen lamps articles from a shattering lamp not impair safety o direct path Impact test on shield Glow-wire test on lamp compartment (4.22) Attachments to lamps (4.23) Semi-luminaires comply class II (4.24) UV radiation, metal halide lamps (4.25) o sharp point or edges (4.26) Short-circuit protection: (4.26.1) (4.26.2) Uninsulated accessible SELV parts Short-circuit test o uninsulated accessible SELV parts age 10 of 30

11 IEC and/or E Ref. o.: CE10- LIE040101S (4.26.3) Test chain according to Figure (11) CREEAGE DISTACES AD CLEARACES Working voltage (V) V Voltage form AC TI >600 Rated pulse voltage (kv)... 1) Current-carrying parts of different polarity: 12.2mm cr (mm); cl (mm)... 2) Current-carrying parts and accessible parts: Basic insulation and cr (mm); cl (mm)... grounding protective in structure 3) arts becoming live due to breakdown of basic insulation and metal parts: cr (mm); cl (mm)... 4) Outer surface of cable where it is clamped and metal parts: cr (mm); cl (mm)... 5) ot used 6) Current-carrying parts and supporting Double insulation in surface: structure cr (mm); cl (mm) (7) ROVISIO FOR EARTHIG 1.8 ( ) 1.8 ( ) Accessible metal parts Metal parts in contact with supporting surface Resistance < 0,5 Ω See appended table Two self-tapping screws used Thread-forming screws Thread-forming screw used in a groove Earth makes contact first o connecter used Earth continuity in joints etc. 1.8 (7.2.4) Locking of clamping means Compliance with (7.2.5) Earth terminal integral part of connector socket o connecter socket used 1.8 (7.2.6) Earth terminal adjacent to mains terminals 1.8 (7.2.7) Electrolytic corrosion of the earth terminal age 11 of 30

12 Ref. o.: CE10- LIE040101S IEC and/or E (7.2.8) Material of earth terminal Copper 1.8 (7.2.10) 1.8 (7.2.11) Contact surface bare metal Class II luminaire for looping-in Double or reinforced insulation to functional earth Earthing core coloured green-yellow Green-yellow wire used Length of earth conductor 1.9 (14) SCREW TERMIALS Separately approved; component list (see Annex 1) art of the luminaire (see Annex 2) 1.9 (15) SCREWLESS TERMIALS Separately approved; component list (see Annex 1) art of the luminaire (see Annex 3) (5) EXTERAL AD ITERAL WIRIG (5.2) Supply connection and external wiring (5.2.1) Means of connection... : Terminals (5.2.2) (5.2.3) (5.2.5) (5.2.6) Connecting leads (E) - without a means for connection to the supply o used connecter leads - terminal block specified - relevant information provided - compliance with 4.6, 4.7.1, 4.7.2, , 11.2, 12 and 13.2 of art 1 Type of cable... : Cables equal to HD21 S2 or HD22 S2 (E) ominal cross-sectional area (mm²)... : Type of attachment, X, Y or Z Type Z not connected to screws Cable entries: - suitable for introduction Wire bushing used age 12 of 30

13 IEC and/or E Ref. o.: CE10- LIE040101S (5.2.7) (5.2.8) (5.2.9) (5.2.10) ( ) ( ) ( ) - adequate degree of protection Cable entries through rigid material have rounded edges Insulating bushings: - suitably fixed ot Class Ⅱ equipment - material in bushings - material not likely to deteriorate - tubes or guards made of insulating material Locking of screwed bushings Cord anchorage: - covering protected from abrasion - clear how to be effective - no mechanical or thermal stress - no tying of cables into knots etc. - insulating material or lining Cord anchorage for type X attachment: a) at least one part fixed Type Y attachments b) types of cable c) no damaging of the cable d) whole cable can be mounted e) no touching of clamping screws f) metal screw not directly on cable g) replacement without special tool Glands not used as anchorage Labyrinth type anchorages Adequate cord anchorage for type Y and type Z attachment Tests: - impossible to push cable; unsafe See appended table pull test: 25 times; pull ()... : - torque test: torque (m)... : - displacement 2 mm - no movement of conductors age 13 of 30

14 IEC and/or E (5.2.11) (5.2.12) (5.2.13) (5.2.14) (5.2.15) (5.2.16) (5.2.17) (5.2.18) Ref. o.: CE10- LIE040101S - no damage of cable or cord External wiring passing into luminaire Looping-in terminals o such construct Wire ends not tinned Wire ends tinned: no cold flow Mains plug same protection o used plug Class III luminaire plug Colour code low voltage (E) o such equipment Appliance inlets (IEC 60320) o used inlet Appliance couplers of class II type o standardized interconnecting cables properly assembled Used plug in accordance with o such components - IEC o plug used - other standard (5.3) Internal wiring (5.3.1) ( ) ( ) Internal wiring of suitable size and type 0.75mm 2 Through wiring - not delivered/ mounting instruction o through wiring - factory assembled - socket outlet loaded (A)... : - temperatures... : Green-yellow for earth only Internal wiring connected directly to fixed wiring Cross-sectional area (mm²)... : 0.75mm 2 Insulation thickness 0.6mm Extra insulation added where necessary Internal wiring connected to fixed wiring via internal current-limiting device Adequate cross-sectional area and insulation thickness age 14 of 30

15 IEC and/or E Ref. o.: CE10- LIE040101S ( ) ( ) ( ) (5.3.) (5.3.2) (5.3.3) (5.3.4) (5.3.5) (5.3.6) (5.3.7) Double or reinforced insulation for class II Class I equipment Conductors without insulation SELV current-carrying parts o SELV parts Insulation thickness other than VC or rubber Sharp edges etc. o moving parts of switches etc. Joints, raising/lowering devices Telescopic tubes etc. o twisting over 360 Insulating bushings: - suitable fixed - material in bushings - material not likely to deteriorate - cables with protective sheath Joints and junctions effectively insulated o such structure Strain on internal wiring ot applicable Wire carriers o such luminaire Wire ends not tinned Wire ends tinned: no cold flow 1.11 (8) ROTECTIO AGAIST ELECTRIC SHOCK 1.11 (8.2.1) Live parts not accessible Basic insulated parts not used on the outer surface without appropriate protection rotection in any position Double-ended tungsten filament lamp o such lamp Insulation lacquer not reliable Double-ended high pressure discharge lamp o such lamp Relevant warning according to fitted to the luminaire age 15 of 30

16 IEC and/or E (8.2.2) ortable luminaire adjusted in most unfavourable position Ref. o.: CE10- LIE040101S o portable luminaire 1.11 (8.2.3) Class II luminaire: - basic insulated metal parts not accessible during starter or lamp replacement - basic insulation not accessible other than during starter or lamp replacement - glass protective shields not used as supplementary insulation Class I luminaire with BC lampholder Class I luminaire 1.11 (8.2.4) ortable luminaire: 1.11 (8.2.5) 1.11 (8.2.6) 1.11 (8.2.7) - protection independent of supporting surface ot portable luminaire - terminal block completely covered Compliance with the standard test finger or relevant probe Covers reliably secured Discharging of capacitors 0,5 μf o capacitors used ortable plug connected luminaire with capacitor Other plug connected luminaire with capacitor Discharge device on or within capacitor Discharge device mounted separately 1.12 (12) EDURACE TEST AD THERMAL TEST 1.12 (12.3) 1.12 (12.3.2) Endurance test: - mounting-position... ormal using - test temperature ( C) total duration (h) H - supply voltage: Un factor; calculated voltage 237V (V)... - lamp used... Filament lamp After endurance test: - no part unserviceable See appended table luminaire not unsafe - no damage to track system - marking legible age 16 of 30

17 IEC and/or E Ref. o.: CE10- LIE040101S 1.12 (12.4) 1.12 (12.5) 1.12 (12.6) 1.12 (12.6.1) 1.12 (12.6.2) 1.12 (12.7) 1.12 (12.7.1) 1.12 (12.7.2) - no cracks, deformation etc. Thermal test (normal operation) See appended table 12.4 Thermal test (abnormal operation) Fixed non-adjustable filament lamp luminaires Thermal test (failed lamp control gear condition): Through wiring or looping-in wiring loaded by a o lamp control gear current of (A)... : - case of abnormal conditions... - electronic lamp control gear - measured winding temperature ( C) at 1,1 Un. - measured mounting surface temperature ( C) at 1,1 Un... - calculated mounting surface temperature ( C):... - track-mounted luminaires Temperature sensing control - case of abnormal conditions... - thermal link - manual reset cut-out - auto reset cut-out - measured mounting surface temperature ( C)... - track-mounted luminaires Thermal test (failed lamp control gear in plastic luminaires): Through wiring or lopping-in wiring loaded by a o lamp control gear current of (A)... - case of abnormal conditions... - measured winding temperature ( C) at 1,1 Un. - measured temperature of fixing point/ exposed part ( C) at 1,1 Un... - calculated temperature of fixing point/ exposed part ( C)... Temperature sensing control - thermal link - manual reset cut-out age 17 of 30

18 IEC and/or E Ref. o.: CE10- LIE040101S - auto reset cut-out - measured temperature of fixing point/ exposed part ( C) (9) RESISTACE TO DUST, SOLID OBJECTS AD MOISTURE 1.13 (9.2) Tests for ingress of dust, solid objects and moisture: - classification according to I... I 20 - mounting position during test... Up - fixing screws tightened; torque (m) m - tests according to clauses... - electric strength test afterwards a) no deposit in dust-proof luminaire b) no talcum in dust-tight luminaire c) no trace of water on current-carrying parts or where it could become a hazard d) i) For luminaires without drain holes no water entry d) ii) For luminaires with drain holes no hazardous water entry e) no water in watertight luminaire f) no contact with live parts (I 2X) f) no entry into enclosure (I 3X and I 4X) f) no contact with live parts (I3X and I4X) 1.13 (9.3) Humidity test 48 h 1.14 (10) ISULATIO RESISTACE AD ELECTRIC STREGTH 1.14 (10.2.1) Insulation resistance test Cable or cord covered by metal foil or replaced by a metal rod of mmø... Insulation resistance (MΩ): SELV: - between current-carrying parts of different polarity... - between current-carrying parts and mounting surface... - between current-carrying parts and metal parts of the luminaire... age 18 of 30

19 IEC and/or E Ref. o.: CE10- LIE040101S 1.14 (10.2.2) 1.14 (10.3.1) Other than SELV: - between live parts of different polarity... See appended table between live parts and mounting surface... - between live parts and metal parts... - between live parts of different polarity through action of a switch... Electric strength test Dummy lamp Luminaires with ignitors after 24 h test Luminaires with manual ignitors Test voltage (V): SELV: - between current-carrying parts of different polarity... - between current-carrying parts and mounting surface... - between current-carrying parts and metal parts of the luminaire... Other than SELV: - between live parts of different polarity... See appended table between live parts and mounting surface... - between live parts and metal parts... - between live parts of different polarity through action of a switch... Leakage current (ma)... See appended table (13) RESISTACE TO HEAT, FIRE AD TRACKIG 1.15 Ball-pressure test: (13.2.1) 1.15 (13.3.1) 1.15 (13.3.2) - part tested; temperature ( C)... See appended table part tested; temperature ( C)... eedle flame test (10 s): - part tested... See appended table part tested... Glow wire test (650 C): age 19 of 30

20 IEC and/or E Ref. o.: CE10- LIE040101S 1.15 (13.4.1) - part tested... See appended table part tested... Tracking test: part tested... age 20 of 30

21 IEC and/or E Ref. o.: CE10- LIE040101S ZB AEX ZB, SECIAL ATIOAL CODITIOS (E) (2.2) Class 0 not accepted EUT not Class 0 (3.3) DK: power supply cord with label IT: warning label on Class 0 luminaire (4.5.1) DK: socket-outlets (4.5.1) FR: socket-outlets (5.2.1) CY, DK, FI, SE, GB: type of plug ZC AEX ZC, ATIOAL DEVIATIOS (E) (13.3) DK: eedle flame test during 30 s (13.3) GB: Requirements according to United Kingdom Building Regulation (13.3.2) FR: Glow-wire test 850 C alt. 750 C for luminaires in premises open to public or 960 C for luminaires in emergency exits age 21 of 30

22 Ref. o.: CE10- LIE040101S Critical component list object/part o. manufacturer/trademark type/model technical data standard mark(s) of conformity age 22 of 30

23 Ref. o.: CE10- LIE040101S AEX 2: screw terminals (part of the luminaire) (14) SCREW TERMIALS (14.2) Type of terminal... : illar terminal Rated current (A)... : Max 4A ( ) One or more conductors One conductors ( ) Special preparation ( ) Terminal size 0 Cross-sectional area (mm²)... : 0.75mm 2 (14.3.3) Conductor space (mm)... : 1.5mm (14.4) Mechanical tests (14.4.1) Minimum distance (14.4.2) Cannot slip out (14.4.3) Special preparation (14.4.4) ominal diameter of thread (metric ISO thread) : External wiring o soft metal (14.4.5) Corrosion (14.4.6) ominal diameter of thread (mm)... : 2.88mm Torque (m)... : 0.5m (14.4.7) Between metal surfaces Lug terminal Mantle terminal ull test; pull ()... : 30 (14.4.8) Without undue damage age 23 of 30

24 Ref. o.: CE10- LIE040101S AEX 3: screwless terminals (part of the luminaire) (15) SCREWLESS TERMIALS (15.2) Type of terminal... : Rated current (A)... : (15.3.1) Material (15.3.2) Clamping (15.3.3) Stop (15.3.4) Unprepared conductors (15.3.5) ressure on insulating material (15.3.6) Clear connection method (15.3.7) Clamping independently (15.3.8) Fixed in position ( ) Conductor size Type of conductor (15.5.1) Terminals internal wiring ( ) ull test spring-type terminals (4, 4 samples) ( ) ull test pin or tab terminals (4, 4 samples) Insertion force not exceeding 50 (15.5.2) ermanent connections: pull-off test (20 ) (15.6) Electrical tests Voltage drop (mv) after 1 h (4 samples)... : Voltage drop of two inseparable joints umber of cycles... : Voltage drop (mv) after 10th alt. 25th cycle (4 samples)... : Voltage drop (mv) after 50th alt. 100th cycle (4 samples)... : After ageing, voltage drop (mv) after 10th alt. 25th cycle (4 samples)... : After ageing, voltage drop (mv) after 50th alt. 100th cycle (4 samples)... : (15.7) Terminals external wiring Terminal size and rating age 24 of 30

25 Ref. o.: CE10- LIE040101S (15.8.1) ull test spring-type terminals or welded connections (4 samples); pull ()... : ull test pin or tab terminals or welded connections (4 samples); pull ()... : (15.9) Contact resistance test Voltage drop (mv) after 1 h terminal voltage drop (mv) Voltage drop of two inseparable joints --- Voltage drop after 10th alt. 25th cycle --- Max. allowed voltage drop (mv)...: terminal voltage drop (mv) Voltage drop after 50th alt. 100th cycle --- Max. allowed voltage drop (mv)...: terminal voltage drop (mv) Continued ageing: voltage drop after 10th alt. 25th cycle --- Max. allowed voltage drop (mv)...: terminal voltage drop (mv) Continued ageing: voltage drop after 50th alt. 100th cycle --- Max. allowed voltage drop (mv)...: terminal voltage drop (mv) age 25 of 30

26 Ref. o.: CE10- LIE040101S 3.4 Table: marking Requirement Comment Legible? Yes / o Marking removable? easily Yes / o Curling? Yes / o 5.2 TABLE: rotection of supply cords(strain, twisting, abrasion) ull force () Torque (m) Displacement (mm) Max displacement (mm) Table : protective earthing resistance Test current 10 A Between Result (mω) Limited (mω) ower supply grounding wire to grounding pin TABLE: Endurance test Test Test status Test Test Test status Test Test time Result cycles voltage time voltage 1 ormal mode 2 ormal mode 3 ormal mode 237V 21Hr Disconnect supply 237V 21Hr Disconnect supply 237V 21Hr Disconnect supply 0V 3Hr Work normally, not any damage 0V 3Hr Work normally, not any damage 0V 3Hr Work normally, not any damage age 26 of 30

27 Ref. o.: CE10- LIE040101S 4 ormal mode 5 ormal mode 6 ormal mode 7 ormal mode 8 ormal mode 9 ormal mode 10 ormal mode 237V 21Hr Disconnect supply 237V 21Hr Disconnect supply 237V 21Hr Disconnect supply 237V 21Hr Disconnect supply 237V 21Hr Disconnect supply 237V 21Hr Disconnect supply 237V 21Hr Disconnect supply 0V 3Hr Work normally, not any damage 0V 3Hr Work normally, not any damage 0V 3Hr Work normally, not any damage 0V 3Hr Work normally, not any damage 0V 3Hr Work normally, not any damage 0V 3Hr Work normally, not any damage 0V 3Hr Work normally, not any damage 12 TABLE: Heating test under normal/abnormal operation conditions, thermocouples Condition (12.4) 1.05 times rated power Remark test voltage (V) V --- t1 ( C) t2 ( C) temperature rise dt of part/at: DT ( C) Limited T ( C) Enclosure Enclosure (near lamp) age 27 of 30

28 Ref. o.: CE10- LIE040101S Internal wire near Terminals Internal wire near connector Mounting surface Mounting surface (lamp irradiation) Terminals Remark: Test points Between TABLE: Insulation strength test To Measured insulation Limited insulation resistance Live Enclosure >2 2MΩ eutral Enclosure >2 2MΩ Live eutral >2 2MΩ TABLE: Electric strength after leakage test voltage applied between: Test voltage (V) Breakdown (Yes/o) L/ and enclosure(wrapped foil) 1480 o breakdown Live and eutral 1480 o breakdown Grounding and L/ 1480 o breakdown 10.3 TABLE: leakage current Testing voltage: Rated voltage -- leakage current between: Leakage (ma) (measured) Max Leakage(mA) Live and enclosure age 28 of 30

29 Ref. o.: CE10- LIE040101S eutral and enclosure (13.2.1) TABLE: Ball pressure test temperature test impression Limited Test specimen from 11. temperature diameter diameter ( C) ( C) ( mm) ( mm) Terminals (13.3.2) TABLE: Ignition of non metallic material specimen Test temperature Test time (min) Result Terminals o burning age 29 of 30

30 Ref. o.: CE10- LIE040101S hoto document (EBO authenticate the photo on original report only) *** End of Report *** age 30 of 30