Universal Standard Service, Inc. Test Report No.:CERASL Test Report. : Micro-Star Int'l Co., Ltd. : Wireless 11g CardBus

Transcription

1 Test Report o.:cerasl Test Report Applicant Address Product ane : Micro-Star Int'l Co., Ltd. : o. 69, Li-De St., Jung-He City, Taipei Hsien 235, Taiwan : Wireless 11g CardBus Type Designation : CB54G, MS-6819, CB54G(MS-6819) Date of Receipt : July 10, 2003 Date of Test : July 12, 2003 The Test Results relate only to the sample tested. The test report shall not be reproduced except in full without the written approval of Universal Standard Service, Inc..

2 Test Report o.:cerasl E TEST REPORT E Safety of information technology equipment including electrical business equipment Report reference o.: Compiled by ( + signature ): Approved by ( + signature ): ASL Bryan Lin Edward Su Date of issue: July 15, 2003 Testing laboratory: Universal Standard Service, Inc. Address: 8F-1, o. 266, Sec. 1, WenHua 2 nd Road, Lin Kou Shiang 244, Taipei County, Taiwan Testing location: as above Applicant: Address: Standard: IEC 60950:1999, E 60950:2000 Test procedure: Standard Type of test object: Trademark: Model / type reference: Manufacturer: Factory: Rating: Micro-Star Int'l Co., Ltd. o. 69, Li-De St., Jung-He City, Taipei Hsien 235, Taiwan Wireless CardBus MSI CB54G, MS-6819, CB54G(MS-6819) Micro-Star Int'l Co., Ltd. o. 69, Li-De St., Jung-He City, Taipei Hsien 235, Taiwan See on page 2 -- Other Aspects: The completed test report includes the following documents: (total page 36) Test results given in this report only relate to the specimen(s) tested, calibrated or measured. This report shall not be reproduced other than in full without the written consent of USS. 1-36

3 Test Report o.:cerasl E Test item particulars: Equipment mobility.....: Operating condition....: moveable continuous Tested for IT power systems....: o mains connection IT testing, phase-phase voltage(v)...: Class of equipment..:.a. Class III Mass of equipment (kg)...: Approx. 40g Protection against ingress of water.. : IPXO Possible test case verdicts: - test case does not apply to the object.: (.A.) - test object does meet the requirement : P(ass) - test object does not meet the requirement..: F(ail ) General remarks: (see remark # ) refers to a remark appended to the report. (see appended table) refers to a table appended to the report. Throughout this report a point is used as the decimal separator. The test results presented in this report relate only to the object tested This report shall not be reproduced except in full without the written approval of the testing laboratory. Comments: Brief description of the test sample: The equipment is a Wireless 11g CardBus for general office use. Factory Data: 1. Micro-Star Int'l Co., Ltd. o. 69, Li-De St., Jung-He City, Taipei Hsien 235, Taiwan 2. MSI-Computer Co., Ltd. Longma Tech-Industial Zone, Tangtou Village, Shiyan Town, Baoan District, ShenZhen, P.R.C. 3. Star Electronics (Kunshan) Co., Ltd o.66, East QianJing Road, Kushan, Jiangsu, P.R.C. ote: 1. Models CB54G(MS-6819) and MS-6819 are identical to Model CB54G, except for Model designation. 2. Ambient temperature is 55 C 2-36

4 Test Report o.:cerasl E Copy of marking plate 3-36

5 Test Report o.:cerasl E GEERAL P 1.5 Components P Comply with IEC or relevant component standard Components, which were found to affect safety aspects, comply with the requirements of this standard or within the safety aspects of the relevant IEC component standards (see appended table 1.5.1) Evaluation and testing of components Components, which are certified to IEC and/or national standards, are used correctly within their ratings. Components not covered by IEC standards are tested under the conditions present in the equipment. Dimensions (mm) of mains plug for direct plug-in : Torque and pull test of mains plug for direct plug-in; torque (m); pull ()...: ot direct plug-in type Thermal controls o thermal control Transformers o transformer Interconnecting cables Capacitors in primary circuits...: Class III equipment Double or reinforced insulation bridged by components Bridging capacitors Bridging resistors Accessible parts Components in equipment for IT power systems dto. Class III equipment. P P 4-36

6 Test Report o.:cerasl E Power interface AC power distribution systems...: Class III equipment Input current Voltage limit of hand-held equipment Class III equipment eutral conductor Class III equipment. 1.7 Marking and instructions Power rating -- Rated voltage(s) or voltage range(s) (V)... : ot shown Symbol for nature of supply for d.c.... : -- Rated frequency or frequency range (Hz)... : o direct connection to the AC mains supply. Rated current (ma or A)... : ot shown Manufacturer s name/trademark... : MSI Type/model... : CB54G, MS-6819, CB54G(MS-6819) Symbol of Class II... : Class III equipment. Other symbols... : Certification marks... : Safety instructions Short duty cycles Equipment is designed for continuous operation Supply voltage adjustment... : o voltage/frequency setting Power outlets on the equipment... : o outlet Fuse identification... : o fuse Wiring terminals See below Protective earthing and bonding terminals Class III equipment Terminal for a.c. mains supply conductors Class III equipment Controls and indicators o safety relevant switch or control. P P 5-36

7 Test Report o.:cerasl E Identification, location and marking... : Colours... : Symbols according to IEC : Markings using figures... : o indicators Isolation of multiple power sources... : Class III equipment IT power system Class III equipment Thermostats and other regulating devices o thermostat or other regulating device Language... : Marking and user s manual in English. Version of other language will be provided when national approval Durability The label was subjected to the permanence of marking test. The label was rubbed with cloth soaked with water for 15s and then again for 15s with the cloth soaked with petroleum spirit. After this test there was no damage to the label. The marking on the label did not fade. There was no curling nor lifting of the label edge Removable parts o required markings placed on removable parts Replaceable batteries Language... : Operator access with a tool... : Only SELV inside Equipment for restricted access locations... : o restricted access location. P P 2 PROTECTIO FROM HAZARDS 6-36

8 Test Report o.:cerasl E Protection from electric shock and energy hazards Protection in operator access areas Access to energised parts Test by inspection...: Test with test finger...: Test with test pin...: Test with test probe...: Battery compartments...: Access to ELV wiring Working voltage (V); distance (mm) trough insulation Access to hazardous voltage circuit wiring Energy hazards...: o energy hazard in operator access area. The connectors on the backside of the equipment below 240VA Manual controls o manual controls Discharge of capacitor s in the primary circuit Time-constant (s); measured voltage (V)...: Protection in service access areas o maintenance work in operation mode necessary Protection in restricted access locations It is not intended to be used in restricted locations 2.2 SELV circuits General requirements The secondary circuits were tested as SELV. See to Voltages under normal conditions (V)...: 42.4V peak or 60Vd.c. are not exceeded in SELV circuit under normal operation, see appended table

9 Test Report o.:cerasl E Voltages under fault conditions (V)...: Single fault did not cause excessive voltage in accessible SELV circuits. Limits of 71V peak and 120Vd.c. did not exceeded within 0.2s and limits 42.4V peak and 60Vd.c. did not exceeded for longer than 0.2 s, see appended tables and Separation by double or reinforced insulation (method 1) Class III equipment Separation by earthed screen (method 2) dto Protection by earthing of the SELV circuit (method 3) Connection of SELV circuits to other circuits...: dto Only SELV circuit provided. 2.3 TV circuits o TV circuit Limits Type of TV circuits...: Separation from other circuits and from accessible parts Used insulation...: Separation from hazardous voltages Used insulation...: Connection of TV circuits to other circuits Used insulation...: Test for operating voltages generated externally 2.4 Limited current circuits General requirements Limit values 8-36

10 Test Report o.:cerasl E Frequency (Hz)... : Measured current (ma)... : Measured voltage (V)... : Measured capacitance (µf)... : Connection of limited current circuits to other circuits 2.5 Limited power sources Inherently limited output Impedance limited output Overcurrent protective device limited output Regulating network limited output under normal operating and single fault condition Regulating network limited output under normal operating conditions and overcurrent protective device limited output under single fault condition Output voltage (V), output current (A), apparent power (VA)...: Current rating of overcurrent protective device (A) 2.6 Provisions for earthing and bonding Class III equipment Protective earthing Functional earthing Protective earthing and protective bonding conductors Size of protective earthing conductors Rated current (A), cross-sectional area (mm 2 ), AWG...: Size of protective bonding conductors 9-36

11 Test Report o.:cerasl E Rated current (A), cross-sectional area (mm 2 ), AWG... : Rated current (A), type and nominal thread diameter (mm)... : Resistance (Ω) of earthing conductors and their terminations, test current (A)... : Colour of insulation... : Terminals Protective earthing and bonding terminals Rated current (A), type and nominal thread diameter (mm)... : Separation of the protective earthing conductor from protective bonding conductors Integrity of protective earthing Interconnection of equipment Components in protective earthing conductors and protective bonding conductors Disconnection of protective earth Parts that can be removed by an operator Parts removed during servicing Corrosion resistance Screws for protective bonding Reliance on telecommunication network 2.7 Overcurrent and earth fault protection in primary circuits Basic requirements Faults not covered in Short-circuit backup protection umber and location of protective devices.. : Protection by several devices Warning to service personnel...: 10-36

12 Test Report o.:cerasl E Safety interlocks o safety interlock General principles Protection requirements Inadvertent reactivation Fail-safe operation Interlocks with moving parts Overriding an interlock Switches and relays in interlock systems Contact gaps (mm)...: Overload test Endurance test Electric strength test (V) Mechanical actuators 2.9 Electrical insulation Properties of insulating materials Humidity conditioning Requirements for insulation Insulation parameters Categories of insulation 2.10 Clearances, creepage distances and distances through insulation See also sub clause General Determination of working voltage Clearances General Clearances in primary circuit 11-36

13 Test Report o.:cerasl E Clearances in secondary circuits Measurement of transient levels Creepage distances CTI tests...: Solid insulation Minimum distance through insulation Thin sheet material umber of layers (pcs)... : Electric strength test Printed boards... : Wound components... : Coated printed boards o coated printed boards General Sample preparation and preliminary inspection... : Thermal cycling... : Thermal ageing... : Electric strength test Abrasion resistance test... : Electric strength test Enclosed and sealed parts... : o hermetically sealed components Spacings filled by insulating compound... : Electric strength test Component external terminations Insulation with varying dimensions Insulation kept homogenous. 3 WIRIG, COECTIOS AD SUPPLY 3.1 General 12-36

14 Test Report o.:cerasl E Current rating and overcurrent protection All internal wires are UL recognized wiring which is PVC insulated, rated VW-1, minimum 80 o C, 300V. Internal wiring gauge is suitable for current intended to be carried. o internal wire for primary power distribution Protection against mechanical damage Securing of internal wiring Insulation of conductors Beads and ceramic insulators Screws for electrical contact pressure on-metallic materials in electrical connections Self-tapping and spaced thread screws Termination of conductors Sleeving on wiring 3.2 Connection to a.c. mains supplies Class III equipment Means of connection Multiple supply connections Permanently connected equipment umber of conductors, diameter (mm) of cable and conduits...: Appliance inlets Power supply cords Type...: Rated current (A), cross-sectional area (mm 2 ), AWG...: Cord anchorages and strain relief 13-36

15 Test Report o.:cerasl E Mass of equipment (kg), pull ()...: Longitudinal displacement (mm)...: Protection against mechanical damage Cord guards D (mm); test mass (g)...: Radius of curvature of cord (mm)...: Supply wiring space 3.3 Wiring terminals for connection of external conductors Class III equipment Wiring terminals Connection of non-detachable power supply cords Screw terminals Rated current (A), cord/cable type, cross-sectional area (mm 2 )...: Rated current (A), type and nominal thread diameter (mm)...: Wiring terminals design Grouping of wiring terminals Standard wire 3.4 Disconnection from the a.c. mains supply Class III equipment General requirement Disconnect devices Permanently connected equipment Parts which remain energized Switches in flexible cords Single-phase equipment Three-phase equipment 14-36

16 Test Report o.:cerasl E Switches as disconnect devices Plugs as disconnect devices Interconnected equipment Multiple power sources 3.5 Interconnection of equipment General requirements See below Types of interconnection circuits... : Interconnection circuits of SELV through the connectors. o ELV interconnection circuits ELV circuits as interconnection circuits o ELV interconnection 4 PHYSICAL REQUIREMETS P 4.1 Stability Angle of 10 Test: force ()... : Equipment is not a floorstanding unit. 4.2 Mechanical strength General Steady force test, Steady force test, Steady force test, Impact test Drop test Stress relief Cathode ray tubes Picture tube separately certified... : Picture tubes > 16 cm intrinsically protected on-intrinsically protected tubes > 16cm used with protective screen 15-36

17 Test Report o.:cerasl E Intrinsically protected tubes: tests on 12 samples Samples subject to ageing: 6 Samples subject to implosion test: 6 Samples subject to mechanical strength test (steel ball): 6 on-intrinsically protected tubes tested High pressure lamps Wall or ceiling mounted equipment; force ()... : 4.3 Design and construction P Edges and corners Edges and corners of the enclosure are rounded Handles and manual controls; force ()... : Adjustable controls one that would cause hazard Securing of parts Connection of plugs and sockets Direct plug-in equipment ot direct plug-in type. Torque (m)... : Heating elements in earthed equipment Class III equipment Batteries Oil and grease o oil or grease Dust, powders, liquids and gases Containers for liquids or gases o container for liquid or gas Flammable liquids... : o flammable liquid. Quantity of liquid (l)... : Flash point ( C)... : Radiation; type of radiation... : P 16-36

18 Test Report o.:cerasl E Equipment using lasers, see separate test report of IEC Protection against hazardous moving parts o hazardous moving part General Protection in operator access areas Protection in restricted access locations Protection in service access areas 4.5 Thermal requirements Temperature rises Resistance to abnormal heat 4.6 Openings in enclosures P Top and side openings o electrical enclosure required. Dimensions (mm)... : Bottoms of fire enclosures P Construction of the bottom... : Doors or covers in fire enclosures P Openings in transportable equipment Equipment is not transportable equipment Adhesives for constructional purposes 4.7 Resistance to fire P Reducing the risk of ignition and spread of flame Conditions for a fire enclosure See P 17-36

19 Test Report o.:cerasl E Parts requiring a fire enclosure With having the following components: components in secondary (not supplied by LPS) insulated wiring the fire enclosure is required. However, according to decisions by operating staff meeting (documents OSM/EE (Chairman)9/99, the enclosure of keyboard or similar devices can be accepted to be made of material class HB min. based on abnormal test. There is no fire hazard after 5.3. Enclosure material rated flammability class HB material is acceptable here Parts not requiring a fire enclosure See Materials See below. P General PCB rated V-1 or better. P Materials for fire enclosures See Materials for components and other parts outside fire enclosures Materials for components and other parts inside fire enclosures dto Internal components except small parts are V-2, HF-2 or better Materials for air filter assemblies o air filter assemblies Materials used in high-voltage components o high voltage component. P P 5 ELECTRICAL REQUIREMETS AD SIMULATED ABORMAL CODITIOS P 18-36

20 Test Report o.:cerasl E Touch current and protective conductor current Class III equipment without TV circuit General Equipment under test (EUT) Test circuit Application of measuring instrument Test procedure Test measurements Test voltage (V)... : Measured current (ma)... : Max. allowed current (ma)... : Equipment with touch current exceeding 3.5 A... : Touch currents to and from telecommunication networks Limitation of the touch current to a telecommunication network Test voltage (V)... : Measured current (ma)... : Max. allowed current (ma)... : Summation of touch currents from telecommunication networks... : 5.2 Electric strength Class III equipment General Test procedure 5.3 Abnormal operating and fault conditions Protection against overload and abnormal operation Motors o motor

21 Test Report o.:cerasl E Transformers o isolating transformer used Functional insulation... : Electromechanical components o electromechanical component Simulation of faults o other abnormal tests necessary Unattended equipment Equipment was not intended for unattended use Compliance criteria for abnormal operating and fault conditions During the tests After the tests Considered. 6 COECTIO TO TELECOMMUICATIO ETWORKS o TV. 6.1 Protection of telecommunication network service personnel, and users of other equipment connected to the network, from hazards in the equipment Protection from hazardous voltages Separation of the telecommunication network from earth Requirements Test voltage (V)...: Current in the test circuit (ma)...: Exclusions...: 6.2 Protection of equipment users from overvoltages on telecommunication networks Separation requirements Electric strength test procedure Impulse test Steady-state test Compliance criteria 20-36

22 Test Report o.:cerasl E Protection of telecommunication wiring system from overheating Max. output current (A)... : Current limiting method... : A AEX, TESTS FOR RESISTACE TO HEAT AD FIRE A.1 Flammability test for fire enclosures of movable equipment having a total mass exceeding 18 g, and of stationary equipment (see ) A.1.1 Samples Wall thickness (mm)... : A.1.2 Conditioning of samples; temperature ( C). : A.1.3 Mounting of samples... : A.1.4 Test flame A.1.5 Test procedure A.1.6 Compliance criteria Sample 1 burning time (s)... : Sample 2 burning time (s)... : Sample 3 burning time (s)... : A.2 Flammability test for fire enclosures of movable equipment having a total mass not exceeding 18 kg, and for material and components located inside fire enclosures (see and ) A.2.1 Samples Wall thickness (mm)... : A.2.2 Conditioning of samples; temperature ( C). : A.2.3 Mounting of samples... : A.2.4 Test flame A.2.5 Test procedure A.2.6 Compliance criteria Sample 1 burning time (s)... : Sample 2 burning time (s)... : Sample 3 burning time (s)... : 21-36

23 Test Report o.:cerasl E A.2.7 Alternative test acc. to IEC , cl. 4, 8 Sample 1 burning time (s)... : Sample 2 burning time (s)... : Sample 3 burning time (s)... : A.3 High current arcing ignition test (see ) A.3.1 Samples Wall thickness (mm)... : A.3.2 Test circuit A.3.3 Test electrodes A.3.4 Test procedure A.3.5 Compliance criteria Sample 1 number of arcs to ignition (pcs)... : Sample 2 number of arcs to ignition (pcs)... : Sample 3 number of arcs to ignition (pcs) : Sample 4 number of arcs to ignition (pcs) : Sample 5 number of arcs to ignition (pcs)... : A.4 Hot wire ignition test (see ) A.4.1 Samples Wall thickness (mm)... : A.4.2 Test circuit A.4.3 Mounting of samples... : A.4.4 Test procedure A.4.5 Compliance criteria Sample 1 ignition time (s)... : Sample 2 ignition time (s)... : Sample 3 ignition time (s)... : Sample 4 ignition time (s)... : Sample 5 ignition time (s)... : A.5 Hot flaming oil test (see 4.6.2) 22-36

24 Test Report o.:cerasl E A.5.1 Mounting of samples... : A.5.2 Test procedure A.5.3 Compliance criterion... : A.6 Flammability tests for classifying materials V-0, V-1 or V-2 A.6.1 Samples Wall thickness (mm)... : A.6.2 Conditioning of samples temperature ( C)... : A.6.3 Mounting of samples... : A.6.4 Test procedure A.6.5 Compliance criteria A.6.6 Permitted retest A.7 Flammability test for classifying foamed materials HF-1, HF-2 or HFB A.7.1 Sample Wall thickness (mm)... : A.7.2 Conditioning of samples; temperature ( C). : A.7.3 Test procedure A.7.4 Compliance criteria A.7.5 Compliance criteria, HF-2 A.7.6 Compliance criteria, HF-1 A.7.7 Compliance criteria, HBF A.7.8 Permitted retest, HF-1 or HF-2 A.7.9 Permitted retest, HBF A.8 Flammability test for classifying materials HB A.8.1 Samples Sample thickness (mm)... : A.8.2 Conditioning of samples; temperature ( C). : A.8.3 Mounting of samples... : A.8.4 Test procedure A.8.5 Compliance criteria A.8.6 Permitted retest 23-36

25 Test Report o.:cerasl E A.9 Flammability test for classifying materials 5V A.9.1 Samples Sample thickness (mm)... : A.9.2 Conditioning of samples temperature ( C)... : A.9.3 Test flame A.9.4 Test procedure, test bars A.9.5 Test procedure, test plaques A.9.6 Compliance criteria... : A.9.7 Permitted retest A.10 Stress relief conditioning (see 4.2.7) Temperature ( C)... : B AEX, MOTOR TESTS UDER ABORMAL CODITIOS B.1 General requirements Position...: Manufacturer...: Type...: Rated values...: B.2 Test conditions B.3 Maximum temperatures B.4 Running overload test B.5 Locked-rotor overload test Test duration (days)...: Electric strength test: test voltage (V)...: B.6 Running overload test for DC motors in secondary circuits B.7 Locked-rotor overload test for DC motors in secondary circuits B.7.1 Test procedure B.7.2 Alternative test procedure; test time (h)...: B.7.3 Electric strength test 24-36

26 Test Report o.:cerasl E B.8 Test for motors with capacitors B.9 Test for three-phase motors B.10 Test for series motors Operating voltage (V)...: C AEX, TRASFORMERS Position...: Manufacturer...: Type...: Rated values...: C.1 Overload test C.2 Insulation D AEX, MEASURIG ISTRUMETS FOR TOUCH-CURRET TESTS (see 5.1.4) D.1 Measuring instrument D.2 Alternative measuring instrument E AEX, TEMPERATURE RISE OF A WIDIG (see and 4.5.1) F AEX, MEASUREMET OF CLEARACES AD CREEPAGE DISTACES G AEX, ALTERATIVE METHOD FOR DETERMIIG MIIMUM CLEARACES G.1 Summary of the procedure for determining minimum clearances G.2 Determination of mains transient voltage (V)... : G.3 Determination of telecommunication network transient voltage (V)... : 25-36

27 Test Report o.:cerasl E G.4 Determination of required withstand voltage (V)... : G.5 Measurement of transient levels (V)... : G.6 Determination of minimum clearances... : H AEX, IOIZIG RADIATIO (see ) Ionizing radiation Measured radiation (mr/h)... : Measured high-voltage (kv)... : Measured focus voltage (kv)... : CRT markings... : J AEX, TABLE OF ELECTROCHEMICAL POTETIALS (see ) Metal used...: K AEX, THERMAL COTROLS (see and 5.3.7) K.1 Making and breaking capacity K.2 Thermostat reliability; operating voltage (V): K.3 Thermostat endurance test; operating voltage (V)... : K.4 Temperature limiter endurance; operating voltage (V)... : K.5 Thermal cut-out reliability K.6 Stability of operation L AEX, ORMAL LOAD CODITIOS FOR SOME TYPES OF ELECTRICAL BUSIESS EQUIPMET (see and 4.5.1) L.1 Typewriters o typewriter. L.2 Adding machines and cash registers o adding machine or cash registers. L.3 Erasers o eraser P

28 Test Report o.:cerasl E L.4 Pencil sharpeners o pencil sharpener. L.5 Duplicators and copy machines o duplicator or copy machine. L.6 Motor-operated files o motor-operated file. L.7 Other business equipment See P M AEX, CRITERIA FOR TELEPHOE RIGIG SIGALS (see 2.3.1) M.1 Introduction M.2 Method A M.3 Method B M.3.1 Ringing signal M Frequency (f)... : M Voltage (V)... : M Cadence; time (s), voltage (V)... : M Single fault current (ma)... : M.3.2 Tripping device and monitoring voltage... : M Conditions for use of a tripping device or a monitoring voltage M Tripping device M Monitoring voltage (V)... : U AEX, ISULATED WIDIG WIRES FOR USE WITHOUT ITERLEAVED ISULATIO (see ). Separate test report V AEX, AC POWER DISTRIBUTIO SYSTEMS (see 1.6.1) Class III equipment. V.1 Introduction V.2 T power systems V.3 TT power systems 27-36

29 Test Report o.:cerasl E V.4 IT power systems TABLE: list of critical components P Object/part no. Manufacturer/ trademark Type/model Technical data Standard Mark(s) of conformity 1 ) Enclosure V-HBmin. -- UL PCB V-1 min. -- UL 1 ) an asterisk indicates a mark which assures the agreed level of surveillance TABLE: electrical data (in normal conditions) Fuse # Irated (ma) U (V) P (mw) I (ma) Ifuse (A) Condition/status TABLE: max. V, A, VA test Voltage (rated) (V) Current (rated) (A) Voltage (max.) (V) Current (max.) (A) VA (max.) (VA) 28-36

30 Test Report o.:cerasl E TABLE: discharge test Condition τ calculated (s) τ measured (s) t u 0V (s) Comments TABLE: Hazardous voltage measurement Transformer Location max. Voltage Voltage Limitation Component V peak V d.c TABLE: SEL voltage measurement Location Voltage measured (V) Comments TABLE: limited current circuit measurement Location Voltage (V) Current (ma) Freq. (khz) Limit (ma) Comments TABLE: ground continue test Location Resistant measured (mω) Comments Table: working voltage measurement 29-36

31 Test Report o.:cerasl E Location RMS voltage (V) Peak voltage (V) Comments and TABLE: clearance and creepage distance measurements Clearance cl and creepage distance dcr at/of: Up (V) U r.m.s. (V) Required cl (mm) cl (mm) Required dcr (mm) dcr (mm) TABLE: distance through insulation measurements Distance through insulation di at/of: U r.m.s. (V) Test voltage (V) Required di (mm) di (mm) 4.5 TABLE: temperature rise measurements test voltage (V)... : -- t1 ( C)... : -- t2 ( C)... : -- Rise dt of part/at: dt (K) Allowed dt (K) Temperature rise dt of winding: R 1 (Ω) R 2 (Ω) dt (K) allowed dt (K) insulation class 30-36

32 Test Report o.:cerasl E TABLE: ball pressure test of thermoplastic parts Part allowed impression diameter (mm)...: 2 mm Test temperature ( C) Impression diameter (mm) 4.6.1, Table: enclosure openings Location Size (mm) Comments TABLE: touch current measurement Condition L terminal A (ma) terminal A (ma) Limit (ma) Comments 5.2 TABLE: electric strength tests and impulse tests Test voltage applied between: Test voltage (V) Breakdown Supplementary information 5.3 TABLE: fault condition tests ambient temperature ( C)... : model/type of power supply... : manufacturer of power supply... : rated markings of power supply... : 31-36

33 Test Report o.:cerasl E o. Component no. Fault Test voltage (V) Test time Fuse no. Fuse current (A) Result Supplementary information ote: In fault column, s-c=short-circuited, o-l=over-loaded. A.6.5 TABLE: flammable test for classifying materials V-0, V-1 or V-2 Sample no./ref. 1/A 2/A 3/A 4/A 5/A 6/B 7/B 8/B 9/B 10/B Supplementary information: Afterflame time (s) t 1 or t 2 Total afterflame time (s) for any condition set t 1 + t 2 Afterflame + afterglow (s) after 2nd flame application t for five (5) specimens: A.6.6 TABLE: flammable test for classifying materials V-0, V-1 or V-2 Sample no Afterflame time (s) t 1 or t Afterflame + afterglow (s) after 2nd flame application t 2 +t 3

34 Test Report o.:cerasl E Supplementary information: Total afterflame time (s) for any condition set t 1 + t 2 for five (5) specimens: A.7.4, A.7.5, A.7.6 and A.7.7 Sample no./ref. 1/A 2/A 3/A 4/A 5/A 6/B 7/B 8/B 9/B 10/B TABLE: flammability test for classifying foam materials HF-1, HF-2 or HBF Flame time (s) Glow time (s) Flaming/glowing distance from he end (mm) Supplementary information: Comment (for A.7.7 Burning rate mm/min) 33-36

35 Test Report o.:cerasl E A.7.8 TABLE: flammability test for classifying foam materials HF-1 or HF-2 Sample no Flame time (s) Glow time (s) Flaming/glowing distance from the end (mm) supplementary information: Comment A.7.9 TABLE: flammability test for classifying foam materials HBF Sample no Flame time (s) Glow time (s) Flaming/glowing distance from the end (mm) Supplementary information: Comment (for A.7.7 Burning rate mm/min) A.8.5 TABLE: flammable test for classifying materials HB Sample no Flaming/glowing rate (mm/min) Flaming/glowing distance from reference mark (mm)

36 Test Report o.:cerasl E Supplementary information: A.8.6 TABLE: flammable test for classifying materials HB Sample no Supplementary information: Flaming/glowing rate (mm/min) Flaming/glowing distance from reference mark (mm) A.9.6 TABLE: flammability test for classifying materials 5V Sample no./ ref. 1/A 2/A 3/A 4/A Flaming + glowing time (s) Test bars Burning distance (mm) Flaming + glowing time (s) Test plaques Burning distance (mm) 5/A 6/B 7/B 8/B 9/B 10/B Supplementary information: 35-36

37 Test Report o.:cerasl E A.9.7 TABLE: flammability test for classifying materials 5V Sample no Flaming + glowing time (s) Test bars Burning distance (mm) Flaming + glowing time (s) Test plaques Burning distance (mm) 15 Supplementary information: 36-36