Information technology equipment Safety Part 1: General requirements

Transcription

1 Test Report issued under the responsibility of: Report umber....: TEST REPORT IEC Information technology equipment Safety Part 1: General requirements GTSS Date of issue...: July 23, 2013 Total number of pages pages Testing Laboratory...: Address...: Applicant s name...: Address...: Manufacturer s name.: Address...: Test specification: Global United Technology Services Co., Ltd. 2nd Floor, Block o.2, Laodong Industrial Zone, Xixiang Road Bao an District, Shenzhen, China Shenzhen Concox Information Technology Co., Ltd Floor 4th, Building B, Gaoxinqi Industrial Park, Liuxian 1st Road, District 67, Bao an, Shenzhen, Guangdong. Same as applicant Same as applicant Standard...: IEC :2005 (Second Edition), Am 1: 2009 Test procedure...: on-standard test method..: Test Report Form o...: Test Report Form(s) Originator...: E : A11: A1: A12:2011 Test Report /A IEC60950_1B SGS Fimko Ltd Master TRF...: Dated Test item description...: GPS Vehicle tracker Trade Mark...: -- Model/Type reference...: TR02, TR02, TR02A, GT02A, GT02B, GT02D Ratings...: Class III, IP X0 Jack Wu Project Engineer Michael Chan Technical Director Safety Laboratory

2 Page 2 of 47 Report o.: GTSS Summary of testing: Testing location: Global United Technology Services Co., Ltd. 2nd Floor, Block o.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China Tests performed (name of test and test clause): The sample(s) tested complies with the requirements of IEC/E These tests fulfil the requirements of standard ISO/IEC When determining the test conclusion, the Measurement Uncertainty of test has been considered. Heating test (4.5): Tma = 50 C (declared by manufacturer) Tamb = 25.2 C 25.7 C K-type thermocouple used for temperature measurement. This test report includes: Annex 1: Photos. Summary of compliance with ational Differences Compliance with the ational requirements of CEELEC common modification. Copy of marking plate Remark: 1. The above label is draft of the artwork for marking plate pending approval by ational Certification Bodies and they shall not be affixed to products prior to such approvals. 2. The marking plates of the other models are of the same pattern.

3 Page 3 of 47 Report o.: GTSS Test item particulars...: Equipment mobility...: [] movable [] hand-held [x] transportable [] stationary [] for building-in [] direct plug-in Connection to the mains...: [] pluggable equipment [] type A [] type B [] permanent connection [] detachable power supply cord [] non-detachable power supply cord [x] not directly connected to the mains Operating condition...: [x] continuous [] rated operating / resting time: Access location...: [x] operator accessible [] restricted access location Over voltage category (OVC)...: [] OVC I [] OVC II [] OVC III [] OVC IV [x] other: o direct connection with mains. Mains supply tolerance (%) or absolute mains supply o direct connection with mains values...: Tested for IT power systems...: [] Yes [x] o IT testing, phase-phase voltage (V)...: /A Class of equipment...: [] Class I [] Class II [x] Class III [] ot classified Considered current rating of protective device as -- part of the building installation (A)...: Pollution degree (PD)...: [] PD 1 [x] PD 2 [] PD 3 IP protection class...: IP X0 Altitude during operation (m)...: < 2000 m Altitude of test laboratory (m)...: Shenzhen of China < 2000 m Mass of equipment (kg)...: 94g Possible test case verdicts: - test case does not apply to the test object... : /A (or ) - test object does meet the requirement... : P (Pass) - test object does not meet the requirement... : F (Fail) Testing... : Date of receipt of test item... : July 18, 2013 Date(s) of performance of tests... : July 18, 2013 to July 22, 2013

4 Page 4 of 47 Report o.: GTSS General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(see Enclosure #)" refers to additional information appended to the report. "(see appended table)" refers to a table appended to the report. Throughout this report a point is used as the decimal separator. This document is issued by the company under its General Conditions of Service accessible at Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company s findings at the time of its intervention only and within the limits of Client s instructions, if any. The Company s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated: (a) the results shown in this document refer only to the sample(s) tested and (b) such sample(s) are retained for 1 month. This document cannot be reproduced except in full, without prior approval of the company. General product information: GPS Vehicle tracker, powered by external power source with LPS output or internal lithium battery package. For indoor use only. Model difference: All models are identical except for model o. After comparison, tests carried out on model TR02 were considered representative.

5 Page 5 of 47 Report o.: GTSS IEC /Am1 1 GEERAL P 1.5 Components P General P Comply with IEC or relevant component standard (see appended tables 1.5.1) Evaluation and testing of components P Thermal controls Transformers Interconnecting cables Capacitors bridging insulation Resistors bridging insulation Resistors bridging functional, basic or supplementary insulation Resistors bridging double or reinforced insulation between a.c. mains and other circuits Resistors bridging double or reinforced insulation between a.c. mains and antenna or coaxial cable Components in equipment for IT power systems Surge suppressors General Protection of VDRs Bridging of functional insulation by a VDR Bridging of basic insulation by a VDR Bridging of supplementary, double or reinforced insulation by a VDR P 1.6 Power interface P AC power distribution systems Input current P Voltage limit of hand-held equipment P eutral conductor 1.7 Marking and instructions P Power rating and identification markings P Power rating marking P Multiple mains supply connections...: Rated voltage(s) or voltage range(s) (V)...: 12 V P

6 Page 6 of 47 Report o.: GTSS IEC /Am1 Symbol for nature of supply, for d.c. only...: P Rated frequency or rated frequency range (Hz)...: Rated current (ma or A)...: 22m A P Identification markings P Manufacturer s name or trade-mark or identification mark...: See page 1 Model identification or type reference...: See page 1 P Symbol for Class II equipment only...: Other markings and symbols...: See marking plate P Safety instructions and marking P General P Disconnect devices Overcurrent protective device IT power distribution systems Operator access with a tool Ozone Short duty cycles Supply voltage adjustment...: Methods and means of adjustment; reference to installation instructions...: Power outlets on the equipment...: Fuse identification (marking, special fusing characteristics, cross-reference)...: Wiring terminals Protective earthing and bonding terminals...: Terminals for a.c. mains supply conductors Terminals for d.c. mains supply conductors Controls and indicators P Identification, location and marking...: P Colours...: Symbols according to IEC : Markings using figures... : Isolation of multiple power sources... : Thermostats and other regulating devices... : Durability P Removable parts Replaceable batteries... : P

7 Page 7 of 47 Report o.: GTSS IEC /Am1 Language(s)... : Equipment for restricted access locations... : 2 PROTECTIO FROM HAZARDS P 2.1 Protection from electric shock and energy hazards P Protection in operator access areas P Access to energized parts Test by inspection... : Test with test finger (Figure 2A)... : Test with test pin (Figure 2B)... : Test with test probe (Figure 2C)... : Battery compartments Access to ELV wiring Working voltage (Vpeak or Vrms); minimum distance through insulation (mm) Access to hazardous voltage circuit wiring Energy hazards... : P Manual controls Discharge of capacitors in equipment Measured voltage (V); time-constant (s)... : Energy hazards d.c. mains supply a) Capacitor connected to the d.c. mains supply.. : b) Internal battery connected to the d.c. mains supply... : Audio amplifiers... : Protection in service access areas Protection in restricted access locations 2.2 SELV circuits P General requirements P Voltages under normal conditions (V)... : < 60 V d.c P Voltages under fault conditions (V)... : < 60 V d.c P Connection of SELV circuits to other circuits... : SELV circuits only P 2.3 TV circuits Limits Type of TV circuits... :

8 Page 8 of 47 Report o.: GTSS IEC /Am Separation from other circuits and from accessible parts General requirements Protection by basic insulation Protection by earthing Protection by other constructions... : Separation from hazardous voltages Insulation employed... : Connection of TV circuits to other circuits Insulation employed... : Test for operating voltages generated externally 2.4 Limited current circuits General requirements Limit values Frequency (Hz)... : Measured current (ma)... : Measured voltage (V)... : Measured circuit capacitance (nf or µf)... : Connection of limited current circuits to other circuits 2.5 Limited power sources a) Inherently limited output b) Impedance limited output c) Regulating network limited output under normal operating and single fault condition d) Overcurrent protective device limited output Max. output voltage (V), max. output current (A), max. apparent power (VA)... : Current rating of overcurrent protective device (A).: Use of integrated circuit (IC) current limiters 2.6 Provisions for earthing and bonding Protective earthing Functional earthing Protective earthing and protective bonding conductors

9 Page 9 of 47 Report o.: GTSS IEC /Am General Size of protective earthing conductors Rated current (A), cross-sectional area (mm 2 ), AWG... : Size of protective bonding conductors Rated current (A), cross-sectional area (mm 2 ), AWG... : Protective current rating (A), cross-sectional area (mm 2 ), AWG... : Resistance of earthing conductors and their terminations; resistance (Ω), voltage drop (V), test current (A), duration (min)... : Colour of insulation... : Terminals General Protective earthing and bonding terminals Rated current (A), type, nominal thread diameter (mm)... : Separation of the protective earthing conductor from protective bonding conductors Integrity of protective earthing Interconnection of equipment Components in protective earthing conductors and protective bonding conductors Disconnection of protective earth Parts that can be removed by an operator Parts removed during servicing Corrosion resistance Screws for protective bonding Reliance on telecommunication network or cable distribution system 2.7 Overcurrent and earth fault protection in primary circuits Basic requirements Instructions when protection relies on building installation Faults not simulated in Short-circuit backup protection umber and location of protective devices... : Protection by several devices

10 Page 10 of 47 Report o.: GTSS IEC /Am Warning to service personnel... : 2.8 Safety interlocks General principles Protection requirements Inadvertent reactivation Fail-safe operation Protection against extreme hazard Moving parts Overriding Switches, relays and their related circuits Separation distances for contact gaps and their related circuits (mm)... : Overload test Endurance test Electric strength test Mechanical actuators 2.9 Electrical insulation Properties of insulating materials Humidity conditioning Relative humidity (%), temperature ( C)... : Grade of insulation Separation from hazardous voltages Method(s) used... : 2.10 Clearances, creepage distances and distances through insulation General Frequency... : Pollution degrees... : Reduced values for functional insulation Intervening unconnected conductive parts Insulation with varying dimensions Special separation requirements Insulation in circuits generating starting pulses Determination of working voltage General

11 Page 11 of 47 Report o.: GTSS IEC /Am RMS working voltage Peak working voltage Clearances General Mains transient voltages a) AC mains supply... : b) Earthed d.c. mains supplies... : c) Unearthed d.c. mains supplies... : d) Battery operation... : Clearances in primary circuits Clearances in secondary circuits Clearances in circuits having starting pulses Transients from a.c. mains supply... : Transients from d.c. mains supply... : Transients from telecommunication networks and cable distribution systems... : Measurement of transient voltage levels a) Transients from a mains supply For an a.c. mains supply... : For a d.c. mains supply... : b) Transients from a telecommunication network : Creepage distances General Material group and comparative tracking index CTI tests... : Minimum creepage distances Solid insulation General Distances through insulation Insulating compound as solid insulation Semiconductor devices Cemented joints Thin sheet material General Separable thin sheet material umber of layers (pcs)... : on-separable thin sheet material Thin sheet material standard test procedure

12 Page 12 of 47 Report o.: GTSS IEC /Am1 Electric strength test Thin sheet material alternative test procedure Electric strength test Insulation in wound components Wire in wound components Working voltage... : a) Basic insulation not under stress... : b) Basic, supplementary, reinforced insulation... : c) Compliance with Annex U... : Two wires in contact inside wound component; angle between 45 and : Wire with solvent-based enamel in wound components Electric strength test Routine test Additional insulation in wound components Working voltage... : - Basic insulation not under stress... : - Supplementary, reinforced insulation... : Construction of printed boards Uncoated printed boards Coated printed boards Insulation between conductors on the same inner surface of a printed board Insulation between conductors on different layers of a printed board Distance through insulation umber of insulation layers (pcs)... : Component external terminations Tests on coated printed boards and coated components Sample preparation and preliminary inspection Thermal conditioning Electric strength test Abrasion resistance test Thermal cycling Test for Pollution Degree 1 environment and insulating compound

13 Page 13 of 47 Report o.: GTSS IEC /Am Tests for semiconductor devices and cemented joints Enclosed and sealed parts 3 WIRIG, COECTIOS AD SUPPLY P 3.1 General P Current rating and overcurrent protection P Protection against mechanical damage P Securing of internal wiring P Insulation of conductors Beads and ceramic insulators Screws for electrical contact pressure Insulating materials in electrical connections Self-tapping and spaced thread screws Termination of conductors 10 pull test Sleeving on wiring 3.2 Connection to a mains supply Means of connection Connection to an a.c. mains supply Connection to a d.c. mains supply Multiple supply connections Permanently connected equipment umber of conductors, diameter of cable and conduits (mm)... : Appliance inlets Power supply cords AC power supply cords Type... : Rated current (A), cross-sectional area (mm 2 ), AWG... : DC power supply cords Cord anchorages and strain relief Mass of equipment (kg), pull ()... : Longitudinal displacement (mm)... : Protection against mechanical damage Cord guards

14 Page 14 of 47 Report o.: GTSS IEC /Am1 Diameter or minor dimension D (mm); test mass (g)... : Radius of curvature of cord (mm)... : Supply wiring space 3.3 Wiring terminals for connection of external conductors Wiring terminals Connection of non-detachable power supply cords Screw terminals Conductor sizes to be connected Rated current (A), cord/cable type, cross-sectional area (mm 2 )... : Wiring terminal sizes Rated current (A), type, nominal thread diameter (mm)... : Wiring terminal design Grouping of wiring terminals Stranded wire 3.4 Disconnection from the mains supply General requirement Disconnect devices Permanently connected equipment Parts which remain energized Switches in flexible cords umber of poles - single-phase and d.c. equipment umber of poles - three-phase equipment Switches as disconnect devices Plugs as disconnect devices Interconnected equipment Multiple power sources 3.5 Interconnection of equipment P General requirements P Types of interconnection circuits... : P ELV circuits as interconnection circuits Data ports for additional equipment USB port is only used for data transfer.

15 Page 15 of 47 Report o.: GTSS IEC /Am1 4 PHYSICAL REQUIREMETS P 4.1 Stability Angle of 10 Test force ()... : 4.2 Mechanical strength General Rack-mounted equipment Steady force test, Steady force test, Steady force test, Impact test Fall test Swing test Drop test; height (mm)... : Stress relief test Cathode ray tubes Picture tube separately certified... : High pressure lamps Wall or ceiling mounted equipment; force ()... : Rotating solid media Test to cover on the door.: 4.3 Design and construction P Edges and corners Round and smooth P Handles and manual controls; force ()...: Adjustable controls Securing of parts P Connection by plugs and sockets Direct plug-in equipment Torque... : Compliance with the relevant mains plug standard... : Heating elements in earthed equipment Batteries - Overcharging of a rechargeable battery

16 Page 16 of 47 Report o.: GTSS IEC /Am1 - Unintentional charging of a non-rechargeable battery - Reverse charging of a rechargeable battery - Excessive discharging rate for any battery Oil and grease Dust, powders, liquids and gases Containers for liquids or gases Flammable liquids... : Quantity of liquid (l)... : Flash point ( C)... : Radiation P General P Ionizing radiation Measured radiation (pa/kg)... : Measured high-voltage (kv)... : Measured focus voltage (kv)... : CRT markings... : Effect of ultraviolet (UV) radiation on materials Part, property, retention after test, flammability classification... : Human exposure to ultraviolet (UV) radiation... : Lasers (including laser diodes) and LEDs P Lasers (including laser diodes) Laser class... : Light emitting diodes (LEDs) Class 1 P Other types... : 4.4 Protection against hazardous moving parts General Protection in operator access areas... : Household and home/office document/media shredders Protection in restricted access locations... : Protection in service access areas Protection against moving fan blades General ot considered to cause pain or injury. a).:

17 Page 17 of 47 Report o.: GTSS IEC /Am1 Is considered to cause pain, not injury. b) : Considered to cause injury. c) : Protection for users Use of symbol or warning : Protection for service persons Use of symbol or warning : 4.5 Thermal requirements P General P Temperature tests (see appended table 4.5) P ormal load condition per Annex L... : Temperature limits for materials (see appended table 4.5) P Touch temperature limits (see appended table 4.5) P Resistance to abnormal heat... : 4.6 Openings in enclosures Top and side openings Dimensions (mm)... : Bottoms of fire enclosures Construction of the bottomm, dimensions (mm).. : Doors or covers in fire enclosures Openings in transportable equipment Constructional design measures Dimensions (mm)... : Evaluation measures for larger openings Use of metallized parts Adhesives for constructional purposes Conditioning temperature ( C), time (weeks)... : 4.7 Resistance to fire P Reducing the risk of ignition and spread of flame P Method 1, selection and application of components wiring and materials Method 2, application of all of simulated fault condition tests See appended table Conditions for a fire enclosure P Parts requiring a fire enclosure P

18 Page 18 of 47 Report o.: GTSS IEC /Am Parts not requiring a fire enclosure P Materials P General P Materials for fire enclosures Materials for components and other parts outside fire enclosures Materials for components and other parts inside fire enclosures Materials for air filter assemblies Materials used in high-voltage components P 5 ELECTRICAL REQUIREMETS AD SIMULATED ABORMAL CODITIOS P 5.1 Touch current and protective conductor current General Configuration of equipment under test (EUT) Single connection to an a.c. mains supply Redundant multiple connections to an a.c. mains supply Simultaneous multiple connections to an a.c. mains supply Test circuit Application of measuring instrument Test procedure Test measurements Supply voltage (V)... : Measured touch current (ma)... : Max. allowed touch current (ma)... : Measured protective conductor current (ma)... : Max. allowed protective conductor current (ma).. : Equipment with touch current exceeding 3,5 ma General... : Simultaneous multiple connections to the supply Touch currents to telecommunication networks and cable distribution systems and from telecommunication networks Limitation of the touch current to a telecommunication network or to a cable distribution system Supply voltage (V)... :

19 Page 19 of 47 Report o.: GTSS IEC /Am1 Measured touch current (ma)... : Max. allowed touch current (ma)... : Summation of touch currents from telecommunication networks a) EUT with earthed telecommunication ports... : b) EUT whose telecommunication ports have no reference to protective earth 5.2 Electric strength General Test procedure 5.3 Abnormal operating and fault conditions P Protection against overload and abnormal operation Motors Transformers Functional insulation... : Electromechanical components o electromechanical component provided Audio amplifiers in ITE... : Simulation of faults P Unattended equipment Compliance criteria for abnormal operating and fault conditions During the tests P After the tests P P 6 COECTIO TO TELECOMMUICATIO ETWORKS 6.1 Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment Protection from hazardous voltages Separation of the telecommunication network from earth Requirements Supply voltage (V)... : Current in the test circuit (ma)... : Exclusions... :

20 Page 20 of 47 Report o.: GTSS IEC /Am1 6.2 Protection of equipment users from overvoltages on telecommunication networks Separation requirements Electric strength test procedure Impulse test Steady-state test Compliance criteria 6.3 Protection of the telecommunication wiring system from overheating Max. output current (A)... : Current limiting method... : 7 COECTIO TO CABLE DISTRIBUTIO SYSTEMS 7.1 General 7.2 Protection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment 7.3 Protection of equipment users from overvoltages on the cable distribution system 7.4 Insulation between primary circuits and cable distribution systems General Voltage surge test Impulse test A AEX A, TESTS FOR RESISTACE TO HEAT AD FIRE A.1 Flammability test for fire enclosures of movable equipment having a total mass exceeding 18 kg, and of stationary equipment (see ) A.1.1 Samples... : Wall thickness (mm)... : A.1.2 Conditioning of samples; temperature ( C)... : A.1.3 Mounting of samples... : A.1.4 Test flame (see IEC ) Flame A, B, C or D... : A.1.5 Test procedure A.1.6 Compliance criteria Sample 1 burning time (s)... : Sample 2 burning time (s)... :

21 Page 21 of 47 Report o.: GTSS IEC /Am1 Sample 3 burning time (s)... : A.2 Flammability test for fire enclosures of movable equipment having a total mass not exceeding 18 kg, and for material and components located inside fire enclosures (see and ) A.2.1 Samples, material... : Wall thickness (mm)... : A.2.2 Conditioning of samples; temperature ( C)... : A.2.3 Mounting of samples... : A.2.4 Test flame (see IEC ) Flame A, B or C... : A.2.5 Test procedure A.2.6 Compliance criteria Sample 1 burning time (s)... : Sample 2 burning time (s)... : Sample 3 burning time (s)... : A.2.7 Alternative test acc. to IEC , cl. 5 and 9 Sample 1 burning time (s)... : Sample 2 burning time (s)... : Sample 3 burning time (s)... : A.3 Hot flaming oil test (see 4.6.2) A.3.1 Mounting of samples A.3.2 Test procedure A.3.3 Compliance criterion B AEX B, MOTOR TESTS UDER ABORMAL CODITIOS (see and 5.3.2) B.1 General requirements Position... : Manufacturer... : Type... : Rated values... : B.2 Test conditions B.3 Maximum temperatures B.4 Running overload test B.5 Locked-rotor overload test Test duration (days)... : Electric strength test: test voltage (V)... :

22 Page 22 of 47 Report o.: GTSS IEC /Am1 B.6 Running overload test for d.c. motors in secondary circuits B.6.1 General B.6.2 Test procedure B.6.3 Alternative test procedure B.6.4 Electric strength test; test voltage (V)... : B.7 Locked-rotor overload test for d.c. motors in secondary circuits B.7.1 General B.7.2 Test procedure B.7.3 Alternative test procedure B.7.4 Electric strength test; test voltage (V)... : B.8 Test for motors with capacitors B.9 Test for three-phase motors B.10 Test for series motors Operating voltage (V)... : C AEX C, TRASFORMERS (see and 5.3.3) Position... : Manufacturer... : Type... : Rated values... : Method of protection... : C.1 Overload test C.2 Insulation Protection from displacement of windings...: D AEX D, MEASURIG ISTRUMETS FOR TOUCH-CURRET TESTS (see 5.1.4) D.1 Measuring instrument D.2 Alternative measuring instrument E AEX E, TEMPERATURE RISE OF A WIDIG (see ) F AEX F, MEASUREMET OF CLEARACES AD CREEPAGE DISTACES (see 2.10 and Annex G)

23 Page 23 of 47 Report o.: GTSS IEC /Am1 G AEX G, ALTERATIVE METHOD FOR DETERMIIG MIIMUM CLEARACES G.1 Clearances G.1.1 General G.1.2 Summary of the procedure for determining minimum clearances G.2 Determination of mains transient voltage (V) G.2.1 AC mains supply... : G.2.2 Earthed d.c. mains supplies... : G.2.3 Unearthed d.c. mains supplies... : G.2.4 Battery operation... : G.3 Determination of telecommunication network transient voltage (V)... : G.4 Determination of required withstand voltage (V) G.4.1 Mains transients and internal repetitive peaks... : G.4.2 Transients from telecommunication networks... : G.4.3 Combination of transients G.4.4 Transients from cable distribution systems G.5 Measurement of transient voltages (V) a) Transients from a mains supply For an a.c. mains supply For a d.c. mains supply b) Transients from a telecommunication network G.6 Determination of minimum clearances... : H AEX H, IOIZIG RADIATIO (see ) J AEX J, TABLE OF ELECTROCHEMICAL POTETIALS (see ) Metal(s) used... : K AEX K, THERMAL COTROLS (see and 5.3.8) K.1 Making and breaking capacity K.2 Thermostat reliability; operating voltage (V)... : K.3 Thermostat endurance test; operating voltage (V)... : K.4 Temperature limiter endurance; operating voltage (V)... : K.5 Thermal cut-out reliability

24 Page 24 of 47 Report o.: GTSS IEC /Am1 K.6 Stability of operation L AEX L, ORMAL LOAD CODITIOS FOR SOME TYPES OF ELECTRICAL BUSIESS EQUIPMET (see and 4.5.2) L.1 Typewriters L.2 Adding machines and cash registers L.3 Erasers L.4 Pencil sharpeners L.5 Duplicators and copy machines L.6 Motor-operated files L.7 Other business equipment P P M AEX M, CRITERIA FOR TELEPHOE RIGIG SIGALS (see 2.3.1) M.1 Introduction M.2 Method A M.3 Method B M.3.1 Ringing signal M Frequency (Hz)... : M Voltage (V)... : M Cadence; time (s), voltage (V)... : M Single fault current (ma)... : M.3.2 Tripping device and monitoring voltage... : M Conditions for use of a tripping device or a monitoring voltage M Tripping device M Monitoring voltage (V)... : AEX, IMPULSE TEST GEERATORS (see , , , , 7.3.2, and Clause G.5).1 ITU-T impulse test generators.2 IEC impulse test generator P AEX P, ORMATIVE REFERECES Q AEX Q, Voltage dependent resistors (VDRs) (see ) a) Preferred climatic categories... : b) Maximum continuous voltage... :

25 Page 25 of 47 Report o.: GTSS IEC /Am1 c) Pulse current... : R AEX R, EXAMPLES OF REQUIREMETS FOR QUALITY COTROL PROGRAMMES R.1 Minimum separation distances for unpopulated coated printed boards (see ) R.2 Reduced clearances (see ) S AEX S, PROCEDURE FOR IMPULSE TESTIG (see ) S.1 Test equipment S.2 Test procedure S.3 Examples of waveforms during impulse testing T AEX T, GUIDACE O PROTECTIO AGAIST IGRESS OF WATER (see 1.1.2) U AEX U, ISULATED WIDIG WIRES FOR USE WITHOUT ITERLEAVED ISULATIO (see ) V AEX V, AC POWER DISTRIBUTIO SYSTEMS (see 1.6.1) V.1 Introduction V.2 T power distribution systems W AEX W, SUMMATIO OF TOUCH CURRETS W.1 Touch current from electronic circuits W.1.1 Floating circuits W.1.2 Earthed circuits W.2 Interconnection of several equipments W.2.1 Isolation W.2.2 Common return, isolated from earth W.2.3 Common return, connected to protective earth X AEX X, MAXIMUM HEATIG EFFECT I TRASFORMER TESTS (see clause C.1) X.1 Determination of maximum input current X.2 Overload test procedure

26 Page 26 of 47 Report o.: GTSS IEC /Am1 Y AEX Y, ULTRAVIOLET LIGHT CODITIOIG TEST (see ) Y.1 Test apparatus... : Y.2 Mounting of test samples... : Y.3 Carbon-arc light-exposure apparatus... : Y.4 Xenon-arc light exposure apparatus... : Z AEX Z, OVERVOLTAGE CATEGORIES (see and Clause G.2) AA AEX AA, MADREL TEST (see ) BB AEX BB, CHAGES I THE SECOD EDITIO CC AEX CC, Evaluation of integrated circuit (IC) current limiters CC.1 General CC.2 Test program 1.: CC.3 Test program 2.: DD AEX DD, Requirements for the mounting means of rack-mounted equipment DD.1 General DD.2 Mechanical strength test, variable..: DD.3 Mechanical strength test, 250, including end stops : DD.4 Compliance : EE AEX EE, Household and home/office document/media shredders EE.1 General EE.2 Markings and instructions Use of markings or symbols : Information of user instructions, maintenance and/or servicing instructions : EE.3 Inadvertent reactivation test : EE.4 Disconnection of power to hazardous moving parts: Use of markings or symbols : EE.5 Protection against hazardous moving parts Test with test finger (Figure 2A) :

27 Page 27 of 47 Report o.: GTSS IEC /Am1 Test with wedge probe (Figure EE1 and EE2) :

28 Page 28 of 47 Report o.: GTSS TABLE: List of critical components P Object/part o. Manufacturer/ trademark Type/model Technical data Standard (Edition / year) PWB Various Various V-1 or better, min. 130 o C Enclosure SABIC IOVATIVE PLASTICS US L L C Supplementary information: 940(f1) V-0, 130 o C Thickness. Min.1.6 mm UL 796 UL94 Mark(s) of conformity 1 ) UL UL (E121562) TABLE: Electrical data (in normal conditions) P U (V ) I (A) Irated (A) P (W) Fuse # Ifuse (A) Condition/status ormal operation with max volume. Supplementary information: and Clearance (cl) and creepage distance (cr) at/of/between: Basic/supplementary: TABLE: Clearance and creepage distance measurements U peak (V) U r.m.s. (V) Required cl (mm) cl (mm) Required cr (mm) Reinforced: Supplementary information: cr (mm) TABLE: Distance through insulation measurements Distance through insulation (DTI) at/of: U peak (V) U rms (V) Test voltage Required DTI (mm) DTI (mm) (V) Supplementary information:

29 Page 29 of 47 Report o.: GTSS TABLE: Batteries The tests of are applicable only when appropriate battery data is not available Is it possible to install the battery in a reverse polarity position? o on-rechargeable batteries Rechargeable batteries Discharging Unintentional Charging Discharging Reversed charging charging Max. current during normal condition Max. current during fault condition Meas. current Manuf. Specs. Meas. current Manuf. Specs. Meas. current Manuf. Specs. Meas. current Manuf. Specs. Test results: Verdict - Chemical leaks - Explosion of the battery - Emission of flame or expulsion of molten metal - Electric strength tests of equipment after completion of tests Supplementary information: 4.5 TABLE: Thermal requirements P Supply voltage (V )...: Ambient T min ( C)...: 25.2 Shift to 50 Ambient T max ( C)...: 25.4 Shift to Maximum measured temperature T of part/at:: T ( C) Allowed T max ( C) PCB near IC PCB near D Button Enclosure outside Temperature T of winding: t 1 ( C) R 1 (Ω) t 2 ( C) R 2 (Ω) T ( C) Allowed T max ( C) Insulation class Supplementary information:

30 Page 30 of 47 Report o.: GTSS TABLE: Ball pressure test of thermoplastic parts Part Allowed impression diameter (mm)...: 2 mm Test temperature ( C) Impression diameter (mm) Supplementary information: 4.7 TABLE: Resistance to fire Part Manufacturer of material Type of material Thickness (mm) Flammability class Evidence Supplementary information: 5.2 TABLE: Electric strength tests, impulse tests and voltage surge tests Test voltage applied between: Basic/supplementary: Voltage shape (AC, DC, impulse, surge) Test voltage (V) Breakdo wn Yes / o Reinforced: Supplementary information: 5.3 TABLE: Fault condition tests P Component o. Ambient temperature ( C)...: Power source for EUT: Manufacturer, model/type, output rating...: Fault Supply voltage (V) Test time Fuse # -- current (A) Observation C54 s-c 5 < 1 s -- 0 Unit shut down immediately. o hazard. D1 s-c 5 < 1 s -- 0 Unit shut down immediately. o hazard. IC1 pin 5-7 s-c 5 < 1 s -- 0 Unit shut down immediately. o hazard. Supplementary information:

31 Page 31 of 47 Report o.: GTSS ATTACHMET ATTACHMET TO TEST REPORT IEC EUROPEA GROUP DIFFERECES AD ATIOAL DIFFERECES Information technology equipment Safety Differences according to...: PART 1: GEERAL REQUIREMETS E :2006/A11:2009/A1:2010 E :2006/A11:2009/A1:2010 CEELEC COMMO MODIFICATIOS IEC , GROUP DIFFERECES (CEELEC common modifications E) Contents Add the following annexes: Annex ZA (normative) ormative references to international publications with their corresponding European publications P Annex ZB (normative) Special national conditions General Delete all the country notes in the reference document (IEC :2005) according to the following list: P ote ote 2 & ote ote ote ote 4, 5 & ote ote ote ote ote ote 2 & ote ote ote ote ote ote ote 1 & ote ote ote ote 3 & ote 1 6 ote 2 & ote ote ote ote ote 7.1 ote ote 7.3 ote 1 & 2 G.2.1 ote 2 Annex H ote 2 General Delete all the country notes in the reference document (IEC P (A1:2010) 1:2005/A1:2010) according to the following list: ote ote ote 2 EE.3 ote

32 Page 32 of 47 Report o.: GTSS ATTACHMET 1.3.Z1 Add the following subclause: 1.3.Z1 Exposure to excessive sound pressure The apparatus shall be so designed and constructed as to present no danger when used for its intended purpose, either in normal operating conditions or under fault conditions, particularly providing protection against exposure to excessive sound pressures from headphones or earphones. OTE Z1 A new method of measurement is described in E , Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - Part 1: General method for one package equipment, and in E , Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - Part 2: Guidelines to associate sets with headphones coming from different manufacturers. Delete Add the following OTE: Added. OTE Z1 The use of certain substances in electrical and electronic equipment is restricted within the EU: see Directive 2002/95/EC In addition, for a PORTABLE SOUD SYSTEM, Added. (A1:2010) the instructions shall include a warning that excessive sound pressure from earphones and headphones can cause hearing loss Replace the subclause as follows: Basic requirements To protect against excessive current, shortcircuits and earth faults in PRIMARY CIRCUITS, protective devices shall be included either as integral parts of the equipment or as parts of the building installation, subject to the following, a), b) and c): a) except as detailed in b) and c), protective devices necessary to comply with the requirements of 5.3 shall be included as parts of the equipment; b) for components in series with the mains input to the equipment such as the supply cord, appliance coupler, r.f.i. filter and switch, shortcircuit and earth fault protection may be provided by protective devices in the building installation;

33 Page 33 of 47 Report o.: GTSS ATTACHMET c) it is permitted for PLUGGABLE EQUIPMET TYPE B or PERMAETLY COECTED EQUIPMET, to rely on dedicated overcurrent and short-circuit protection in the building installation, provided that the means of protection, e.g. fuses or circuit breakers, is fully specified in the installation instructions. If reliance is placed on protection in the building installation, the installation instructions shall so state, except that for PLUGGABLE EQUIPMET TYPE A the building installation shall be regarded as providing protection in accordance with the rating of the wall socket outlet This subclause has been declared void. Declared Delete the OTE in Table 3A, and delete also in this table the conduit sizes in parentheses Replace IEC 53 by H05 RR-F ; IEC 52 by H03 VV-F or H03 VVH2-F ; IEC 53 by H05 VV-F or H05 VVH2-F2. In Table 3B, replace the first four lines by the following: Up to and including 6 0,75 a) Over 6 up to and including 10 (0,75) b) 1,0 Over 10 up to and including 16 (1,0) c) 1,5 In the conditions applicable to Table 3B delete the words in some countries in condition a). In OTE 1, applicable to Table 3B, delete the second sentence In Table 3D, delete the fourth line: conductor sizes for 10 to 13 A, and replace with the following: Over 10 up to and including 16 1,5 to 2,5 1,5 to 4 Delete the fifth line: conductor sizes for 13 to 16 A Deleted. Replaced. Deleted.

34 Page 34 of 47 Report o.: GTSS ATTACHMET (A1:2010) Annex H Replace the existing OTE by the following: OTE Z1 Attention is drawn to: 1999/519/EC: Council Recommendation on the limitation of exposure of the general public to electromagnetic fields 0 Hz to 300 GHz, and 2006/25/EC: Directive on the minimum health and safety requirements regarding the exposure of workers to risks arising from physical agents (artifical optical radiation). Standards taking into account mentioned Recommendation and Directive which demonstrate compliance with the applicable EU Directive are indicated in the OJEC. Replace the last paragraph of this annex by: At any point 10 cm from the surface of the OPERATOR ACCESS AREA, the dose rate shall not exceed 1 μsv/h (0,1 mr/h) (see OTE). Account is taken of the background level. Replace the notes as follows: OTE These values appear in Directive 96/29/Euratom. Delete OTE 2. Replaced. Replaced. Bibliography Additional E standards. Added. ZA ORMATIVE REFERECES TO ITERATIOAL PUBLICATIOS WITH THEIR CORRESPODIG EUROPEA PUBLICATIOS ZB AEX (normative) SPECIAL ATIOAL CODITIOS (E) In Denmark, certain types of Class I appliances (see ) may be provided with a plug not establishing earthing conditions when inserted into Danish socket-outlets In orway and Sweden, for requirements see and 7.3 of this annex In Finland, orway and Sweden, resistors o such resistors. bridging BASIC ISULATIO in CLASS I PLUGGABLE EQUIPMET TYPE A must comply with the requirements in In addition when a single resistor is used, the resistor must withstand the resistor test in In orway, due to the IT power system used (see annex V, Figure V.7), capacitors are required to be rated for the applicable line-to-line voltage (230 V) In Finland, orway and Sweden, the third dashed sentence is applicable only to equipment as defined in of this annex. o TV circuits within the equipment.

35 Page 35 of 47 Report o.: GTSS ATTACHMET In Finland, orway and Sweden, CLASS I PLUGGABLE EQUIPMET TYPE A intended for connection to other equipment or a network shall, if safety relies on connection to protective earth or if surge suppressors are connected between the network terminals and accessible parts, have a marking stating that the equipment must be connected to an earthed mains socket-outlet. The marking text in the applicable countries shall be as follows: In Finland: "Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan" In orway: Apparatet må tilkoples jordet stikkontakt In Sweden: Apparaten skall anslutas till jordat uttag In orway and Sweden, the screen of the cable distribution system is normally not earthed at the entrance of the building and there is normally no equipotential bonding system within the building. Therefore the protective earthing of the building installation need to be isolated from the screen of a cable distribution system. It is however accepted to provide the insulation external to the equipment by an adapter or an interconnection cable with galvanic isolator, which may be provided by e.g. a retailer. The user manual shall then have the following or similar information in orwegian and Swedish language respectively, depending on in what country the equipment is intended to be used in: Equipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing and to a cable distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see E ). The marking text must be provided when marketed in applicable countries.

36 Page 36 of 47 Report o.: GTSS ATTACHMET OTE In orway, due to regulation for installations of cable distribution systems, and in Sweden, a galvanic isolator shall provide electrical insulation below 5 MHz. The insulation shall withstand a dielectric strength of 1,5 kv r.m.s., 50 Hz or 60 Hz, for 1 min. Translation to orwegian (the Swedish text will also be accepted in orway): Utstyr som er koplet til beskyttelsesjord via nettplugg og/eller via annet jordtilkoplet utstyr og er tilkoplet et kabel-tv nett, kan forårsake brannfare. For å unngå dette skal det ved tilkopling av utstyret til kabel-tv nettet installeres en galvanisk isolator mellom utstyret og kabel- TV nettet. Translation to Swedish: Utrustning som är kopplad till skyddsjord via jordat vägguttag och/eller via annan utrustning och samtidigt är kopplad till kabel-tv nät kan i vissa fall medfőra risk főr brand. Főr att undvika detta skall vid anslutning av utrustningen till kabel-tv nät galvanisk isolator finnas mellan utrustningen och kabel-tv nätet In Denmark, socket-outlets for providing power to other equipment shall be in accordance with the Heavy Current Regulations, Section D1, Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a, when used on Class I equipment. For STATIOARY EQUIPMET the socket-outlet shall be in accordance with Standard Sheet DK 1-1b or DK 1-5a. For CLASS II EQUIPMET the socket outlet shall be in accordance with Standard Sheet DKA 1-4a In orway, for requirements see , and of this annex In Finland, orway and Sweden there are additional requirements for the insulation. See and of this annex In orway, for requirements see , and of this annex In the United Kingdom, the current rating of the circuit shall be taken as 13 A, not 16 A In the United Kingdom, to protect against excessive currents and short-circuits in the PRIMARY CIRCUIT of DIRECT PLUG-I EQUIPMET, tests according to 5.3 shall be conducted, using an external protective device rated 30 A or 32 A. If these tests fail, suitable protective devices shall be included as integral parts of the DIRECT PLUG-I EQUIPMET, so that the requirements of 5.3 are met In Finland, orway and Sweden, there are additional requirements for the insulation, see and of this annex. o socket-outlets provided. o TV circuits within the equipment. o TV circuits within the equipment. o TV circuits within the equipment. Considered. The equipment is not direct plug-in equipment. o TV circuits within the equipment.

37 Page 37 of 47 Report o.: GTSS ATTACHMET In Switzerland, supply cords of equipment having a RATED CURRET not exceeding 10 A shall be provided with a plug complying with SEV 1011 or IEC and one of the following dimension sheets: SEV Plug Type 15 3P++PE 250/400 V, 10 A SEV Plug Type 11 L+ 250 V, 10 A SEV Plug Type 12 L++PE 250 V, 10 A In general, E applies for plugs for currents exceeding 10 A. However, a 16 A plug and socket-outlet system is being introduced in Switzerland, the plugs of which are according to the following dimension sheets, published in February 1998: SEV : Plug Type 25, 3L++PE 230/400 V, 16 A SEV :Plug Type 21, L+, 250 V, 16A SEV : Plug Type 23, L++PE 250 V, 16 A In Denmark, supply cords of single-phase equipment having a rated current not exceeding13 A shall be provided with a plug according to the Heavy Current Regulations, Section D1. CLASS I EQUIPMET provided with socketoutlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with standard sheet DK 2-1a or DK 2-5a. If poly-phase equipment and single-phase equipment having a RATED CURRET exceeding 13 A is provided with a supply cord with a plug, this plug shall be in accordance with the Heavy Current Regulations, Section D1 or E

38 Page 38 of 47 Report o.: GTSS ATTACHMET In Spain, supply cords of single-phase equipment having a rated current not exceeding 10 A shall be provided with a plug according to UE 20315:1994. Supply cords of single-phase equipment having a rated current not exceeding 2,5 A shall be provided with a plug according to UE-E 50075:1993. CLASS I EQUIPMET provided with socketoutlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules, shall be provided with a plug in accordance with standard UE 20315:1994. If poly-phase equipment is provided with a supply cord with a plug, this plug shall be in accordance with UE-E In the United Kingdom, apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to BS 1363 by means of that flexible cable or cord and plug, shall be fitted with a standard plug in accordance with Statutory Instrument 1768: The Plugs and Sockets etc. (Safety) Regulations 1994, unless exempted by those regulations. OTE Standard plug is defined in SI 1768:1994 and essentially means an approved plug conforming to BS 1363 or an approved conversion plug In Ireland, apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to I.S. 411 by means of that flexible cable or cord and plug, shall be fitted with a 13 A plug in accordance with Statutory Instrument 525: ational Standards Authority of Ireland (section 28) (13 A Plugs and Conversion Adaptors for Domestic Use) Regulations In Switzerland, for requirements see of this annex In the United Kingdom, a power supply cord with conductor of 1,25 mm2 is allowed for equipment with a rated current over 10 A and up to and including 13 A In the United Kingdom, the range of conductor sizes of flexible cords to be accepted by terminals for equipment with a RATED CURRET of over 10 A up to and including 13 A is: 1,25 mm 2 to 1,5 mm 2 nominal cross-sectional area.

39 Page 39 of 47 Report o.: GTSS ATTACHMET In the United Kingdom, the torque test is performed using a socket outlet complying with BS 1363 part 1:1995, including Amendment 1:1997 and Amendment 2:2003 and the plug part of DIRECT PLUG-I EQUIPMET shall be assessed to BS 1363: Part 1, 12.1, 12.2, 12.3, 12.9, 12.11, 12.12, 12.13, and 12.17, except that the test of is performed at not less than 125 C. Where the metal earth pin is replaced by an Insulated Shutter Opening Device (ISOD), the requirements of clauses 22.2 and 23 also apply In Ireland, DIRECT PLUG-I EQUIPMET is known as plug similar devices. Such devices shall comply with Statutory Instrument 526: ational Standards Authority of Ireland (Section 28) (Electrical plugs, plug similar devices and sockets for domestic use) Regulations, In Finland, orway and Sweden TOUCH CURRET measurement results exceeding 3,5 ma r.m.s. are permitted only for the following equipment: STATIOARY PLUGGABLE EQUIPMET TYPE A that is intended to be used in a RESTRICTED ACCESS LOCATIO where equipotential bonding has been applied, for example, in a telecommunication centre; and has provision for a permanently connected PROTECTIVE EARTHIG CODUCTOR; and is provided with instructions for the installation of that conductor by a SERVICE PERSO; STATIOARY PLUGGABLE EQUIPMET TYPE B; STATIOARY PERMAETLY COECTED EQUIPMET. The equipment is not direct plug-in equipment. The equipment is not direct plug-in equipment. The equipment is not such equipment.

40 Page 40 of 47 Report o.: GTSS ATTACHMET (A1:2010) In Finland, orway and Sweden, add the following text between the first and second paragraph of the compliance clause: If this insulation is solid, including insulation forming part of a component, it shall at least consist of either - two layers of thin sheet material, each of which shall pass the electric strength test below, or - one layer having a distance through insulation of at least 0,4 mm, which shall pass the electric strength test below. Alternatively for components, there is no distance through insulation requirements for the insulation consisting of an insulating compound completely filling the casing, so that CLEARACES and CREEPAGE DISTACES do not exist, if the component passes the electric strength test in accordance with the compliance clause below and in addition - passes the tests and inspection criteria of with an electric strength test of 1,5 kv multiplied by 1,6 (the electric strength test of shall be performed using 1,5 kv), and - is subject to ROUTIE TESTIG for electric strength during manufacturing, using a test voltage of 1,5 kv. It is permitted to bridge this insulation with an optocoupler complying with b). It is permitted to bridge this insulation with a capacitor complying with E :2005, subclass Y2. A capacitor classified Y3 according to E :2005, may bridge this insulation under the following conditions: - the insulation requirements are satisfied by having a capacitor classified Y3 as defined by E , which in addition to the Y3 testing, is tested with an impulse test of 2,5 kv defined in E :2006, ; - the additional testing shall be performed on all the test specimens as described in E ; - the impulse test of 2,5 kv is to be performed before the endurance test in E , in the sequence of tests as described in E o TV circuits within the equipment.

41 Page 41 of 47 Report o.: GTSS ATTACHMET In Finland, orway and Sweden, the exclusions are applicable for PERMAETLY COECTED EQUIPMET, PLUGGABLE EQUIPMET TYPE B and equipment intended to be used in a RESTRICTED ACCESS LOCATIO where equipotential bonding has been applied, e.g. in a telecommunication centre, and which has provision for a permanently connected PROTECTIVE EARTHIG CODUCTOR and is provided with instructions for the installation of that conductor by a SERVICE PERSO. 7.2 In Finland, orway and Sweden, for requirements see and of this annex. The term TELECOMMUICATIO ETWORK in being replaced by the term CABLE DISTRIBUTIO SYSTEM. 7.3 In orway and Sweden, for requirements see and of this annex. 7.3 In orway, for installation conditions see E :2005. o TV circuits within the equipment. The equipment is not connected to the distribution systems.

42 Page 42 of 47 Report o.: GTSS ATTACHMET ATTACHMET TO TEST REPORT IEC EUROPEA GROUP DIFFERECES AD ATIOAL DIFFERECES Information technology equipment Safety Differences according to...: PART 1: GEERAL REQUIREMETS E :2006/A12:2011 Zx. Protection against excessive sound pressure from personal music players Zx.2 For equipment provided as package: Acoustic output L Aeq,T while playing the fixed "programme simulation noise" of E (dba)... : For personal music player with analogue electrical output for a listening device: Electrical output as described in E while playing the fixed "programme simulation noise" of E (mv)... : Equipment exempted from safety provisions a) to e) below a) Protection of user provided against unintentional acoustic outputs exceeding stated levels b) Equipment has a standard acoustic output level not exceeding stated levels, and automatically returns to an output level not exceeding stated levels when the power is switched off c) Means for actively informing user of increased sound pressure when operated with an acoustic output exceeding stated levels d) Warning of subclause Zx.3 provided e) 1) For equipment provided as package: Acoustic output L Aeq,T while playing the fixed "programme simulation noise" of E (dba)... : e) 2) For personal music player with analogue electrical output for a listening device: Electrical output as described in E while playing the fixed "programme simulation noise" of E (mv)... : Zx.3 Warning Symbol of IEC provided Height of symbol (mm)... : Wording "To prevent possible heraing damage, do not listen at high volume levels for long periods.", or similar, provided

43 Page 43 of 47 Report o.: GTSS ATTACHMET Alternative warning method used Zx.4 Requirements for listening devices (headphones and earphones) Zx.4.1 Wired listening devices with analogue input Input voltage with 94 dba sound pressure output L Aeq,T while playing the fixed "programme simulation noise" of E (mv)... : Zx.4.2 Wired listening devices with digital input Acoustic output L Aeq,T of listening device with any playing device playing the fixed "programme simulation noise" of E (and respecting the digital interface standards, where a digital interface standard exists that specifies the equivalent acoustic level) (dba)... : Digital interface standards used for testing... : Equipment modes considered during testing... : Zx.4.3 Wireless listening devices Acoustic output L Aeq,T of listening device (in wireless mode) (dba)... : Any playing and transmitting device playing the fixed "programme simulation noise" of E Wireless transmission standard used for testing : Setting of volume and sound settings in the listening device... : Zx.5 Measurement methods Time interval T according to E or E , as applicable (s)... :

44 Page 44 of 47 Report o.: GTSS ATTACHMET Differences according to...: ATTACHMET TO TEST REPORT IEC FILAD ATIOAL DIFFERECES Information technology equipment Safety PART 1: GEERAL REQUIREMETS E :2006/A11:2009/A1:2010 ational Differences General See also Group Differences (E :2006/A11/A1) In Finland resistors bridging BASIC ISULATIO in CLASS I PLUGGABLE EQUIPMET TYPE A must comply with the requirements in In addition when a single resistor is used, the resistor must withstand the resistor test in o such resistors In Finland, the third dashed sentence is applicable only to equipment as defined in of this annex In Finland,CLASS I PLUGGABLE EQUIPMET TYPE A intended for connection to other equipment or a network shall, if safety relies on connection to protective earth or if surge suppressors are connected between the network terminals and accessible parts, have a marking stating that the equipment must be connected to an earthed mains socket-outlet. The marking text in in Finland shall be as follows: "Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan" In Finland, there are additional requirements for the insulation. See and of this annex In Finland, there are additional requirements for the insulation, see and of this annex. o TV circuits within the equipment. The marking text must be provided when marketed in Finland. o TV circuits within the equipment. o TV circuits within the equipment.

45 Page 45 of 47 Report o.: GTSS ATTACHMET In Finland, TOUCH CURRET measurement results exceeding 3,5 ma r.m.s. are permitted only for the following equipment: STATIOARY PLUGGABLE EQUIPMET TYPE A that - is intended to be used in a RESTRICTED ACCESS LOCATIO where equipotential bonding has been applied, for example, in a telecommunication centre; and - has provision for a permanently connected PROTECTIVE EARTHIG CODUCTOR; and - is provided with instructions for the installation of that conductor by a SERVICE PERSO; STATIOARY PLUGGABLE EQUIPMET TYPE B; STATIOARY PERMAETLY COECTED EQUIPMET (A1:2010) In Finland, add the following text between the first and second paragraph of the compliance clause: If this insulation is solid, including insulation forming part of a component, it shall at least consist of either - two layers of thin sheet material, each of which shall pass the electric strength test below, or - one layer having a distance through insulation of at least 0,4 mm, which shall pass the electric strength test below. Alternatively for components, there is no distance through insulation requirement for the insulation consisting of an insulating compound completely filling the casing, so that CLEARACES and CREEPAGE DISTACES do not exist, if the component passes the electric strength test in accordance with the compliance clause below and in addition - passes the tests and inspection criteria of with an electric strength test of 1,5 kv multiplied by 1,6 (the electric strength test of shall be performed using 1,5 kv), and - is subject to ROUTIE TESTIG for electric strength during manufacturing, using a test voltage of 1,5 kv. The equipment is not such equipment. o TV circuits within the equipment.

46 Page 46 of 47 Report o.: GTSS ATTACHMET It is permitted to bridge this insulation with an optocoupler complying with b). It is permitted to bridge this insulation with a capacitor complying with E :2005, subclass Y2. A capacitor classified Y3 according to E :2005, may bridge this insulation under the following conditions: - the insulation requirements are satisfied by having a capacitor classified Y3 as defined by E :2005 which in addition to the Y3 testing, is tested with an impulse test of 2,5 kv defined in E :2006, ; - the additional testing shall be performed on all the test specimens as described in E :2005; - the impulse test of 2,5 kv is to be performed before the endurance test in E :2005, in the sequence of tests as described in E : In Finland, the exclusions are applicable for PERMAETLY COECTED EQUIPMET, PLUGGABLE EQUIPMET TYPE B and equipment intended to be used in a RESTRICTED ACCESS LOCATIO where equipotential bonding has been applied, e.g. in a telecommunication centre, and which has provision for a permanently connected PROTECTIVE EARTHIG CODUCTOR and is provided with instructions for the installation of that conductor by a SERVICE PERSO. 7.2 In Finland, for requirements see and of this annex. The term TELECOMMUICATIO ETWORK in being replaced by the term CABLE DISTRIBUTIO SYSTEM. o TV circuits within the equipment. The equipment is not connected to the distribution systems.

47 Page 47 of 47 Report o.: GTSS ATTACHMET ATTACHMET TO TEST REPORT IEC GERMAY ATIOAL DIFFERECES Information technology equipment Safety PART 1: GEERAL REQUIREMETS Differences according to...: VDE : Annex ZC, According to GPSG, section 2, clause 4: If certain rules on the use, supplementation or maintenance of an item of technical work equipment or ready-to-use commodity must be observed in order to guarantee safety and health, instructions for use in German must be supplied when it is brought into circulation. Shall be evaluated during the national approval.

48 Annex o. 1 Report o.: GTSS Page 1 of 6 Photo documentation Type of equipment, model: GPS Vehicle tracker, TR02

49 Annex o. 1 Report o.: GTSS Page 2 of 6

50 Annex o. 1 Report o.: GTSS Page 3 of 6

51 Annex o. 1 Report o.: GTSS Page 4 of 6

52 Annex o. 1 Report o.: GTSS Page 5 of 6

53 Annex o. 1 Report o.: GTSS Page 6 of 6 **********End of Annex 1**********