LOW VOLTAGE DIRECTIVE TEST REPORT IEC / EN , First Edition Information technology equipment Safety Part 1: General requirements

Transcription

1

2 page 1 of 39 Report No.: L7D1808L658 LOW VOLTAGE DIRECTIVE TEST REPORT IEC / EN , First Edition Information technology equipment Safety Part 1: General requirements Report Reference No.... : L7D1808L658 Compiled by (+ signature)... : Moly Chen Project Engineer Approved by (+ signature)... : Jason Chuang Director Date of Issue... : February 14, 2008 Testing laboratory... : Sporton International Inc. Address... : 14Fl.-2, No. 186, Jianyi Rd., Junghe City, Taipei Hsien, Testing location... : Taiwan Applicant... : Realtek Semiconductor Corp. Moly Chen Address... : No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Standard... : IEC : 2001 EN : A11: 2004 Test Report Form No.... : LVD Test procedure... : Sporton LVD type test approval Procedure deviation... : N/A Non-standard test method... : N/A Type of test object... : b/g RTL8187SE minicard Trademark... : Realtek Model/type reference... : RTL8187SE Manufacturer... : Realtek Semiconductor Corp. Rating... : +3.3 Vdc, 500 ma No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan

3 page 2 of 39 Report No.: L7D1808L658 Test item particulars: Equipment mobility...: for building-in Operating condition...: continuous Tested for IT power systems...: No IT testing, phase-phase voltage (V)...: Class of equipment...: Class III Mass of equipment (kg)...: approx. 6 g Protection against ingress of water...: IP X0 Possible test case verdicts: - test case does not apply to the test object...: - test object does meet the requirement...: Pass - test object does not meet the requirement...: Fail Testing: - Date of receipt of test item...: Feb. 4, Date(s) of performance of test...: Feb. 4 - Feb. 14, 2008 General remarks: "(see remark #)" refers to a remark appended to the report. "(see appended table)" refers to a table appended to the report. Throughout this report a point is used as the decimal separator. The test results presented in this report relate only to the object tested. This report shall not be reproduced except in full without the written approval of the testing laboratory. Comments: The test results are true for the test sample(s) only. A part of this test report or certificate should not be duplicated in any way; however, the duplication of the whole document is allowed. This test-report includes the following documents: Test report - (37 pages) Photo - (3 pages)

4 page 3 of 39 Report No.: L7D1808L658 Brief description of the test sample: The equipment is a b/g RTL8187SE minicard, intended for used with information technology equipment. Overall dimensions of the equipment were approximate 53 by 30 mm. The above models were evaluated for use in a maximum air ambient of 25ºC. The test sample is pre-production without serial number. Antenna type detail : Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 2.11 Connector IPEX Model No. DQ Connector IPEX Model No. DQ Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 2.11 Connector IPEX Model No. AR830WIPI02A Connector IPEX Model No. AR320WIPI02B Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 2.41 Connector IPEX Model No. ARW62WIP101G Connector IPEX Model No. ARUMPWIPI02 Ant. Type PIFA PK Gain(dBi) 2.32 Ant. Type PIFA PK Gain(dBi) Connector IPEX Model No. WDAN-GQMA6001-DF Connector IPEX Model No. WDAN-GQMA6002-DF Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 3.25 Connector IPEX Model No NC3587 Connector IPEX Model No NC3586 Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 0.64 Connector IPEX Model No. AAFQ LK0 Connector IPEX Model No. HFT40-IV17 Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 1.34 Connector IPEX Model No. 81.EE Connector IPEX Model No. ASAW001 Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 0.61 Connector IPEX Model No. B G0003 Connector IPEX Model No. ASAT001 Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 1.12 Connector IPEX Model No. ASAA001 Connector IPEX Model No. HFT40 Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 2.24 Connector IPEX Model No. HFT60 Connector IPEX Model No. HTL008 Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 3.45 Connector IPEX Model No. HTL017 Connector IPEX Model No. TBN001 Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 0.87 Connector IPEX Model No. TBN003 Connector IPEX Model No. TIAN01 Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 1.75 Connector IPEX Model No. WNC001 Connector IPEX Model No. WNC002

5 page 4 of 39 Report No.: L7D1808L658 Antenna type detail : Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Connector IPEX Model No. U40 Connector IPEX Model No. U40 Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 0.94 Connector IPEX Model No. U50 Connector IPEX Model No. U50 Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 2.04 Connector IPEX Model No. MA-8 ( ) Connector IPEX Model No. MA-8 ( ) Ant. Type PIFA PK Gain(dBi) 0.11 Ant. Type PIFA PK Gain(dBi) 2.75 Connector IPEX Model No. SA-1( ) 34 Connector IPEX Model No. WDAN-GQMA3004- F Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 0.95 Connector IPEX Model No. L45II-WLAN Connector IPEX Model No. L55II-ID1 & ID2 Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 2.14 Connector IPEX Model No. L55II-ID3 Connector IPEX Model No. L55II-ID4 Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 2.21 Connector IPEX Model No. L55 RI Connector IPEX Model No. UM700-L Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Connector IPEX Model No. W351 Connector IPEX Model No. W651 Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 0.7 Connector IPEX Model No. W815UI1 Connector IPEX Model No. NB0040-K Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) 1.68 Connector IPEX Model No. TFF-A011MPXX-361 Connector IPEX Model No. L45 Ant. Type PIFA PK Gain(dBi) 2.83 Connector IPEX Model No. MCA50

6 page 5 of 39 Report No.: L7D1808L658 Clause Requirement - Test Result - Remark Verdict 1 GENERAL Pass 1.5 Components Pass Comply with IEC or relevant component Safety involved components comply Pass standard with the requirements of this standard or within the safety aspects of the relevant IEC component standards (refer to appended table below) Evaluation and testing of components Components which are certified to IEC Pass and/or national standards are used correctly within their ratings. Components not covered by IEC standards are tested under the conditions present in the equipment Thermal controls Transformers Interconnecting cables Capacitors in primary circuits Double or reinforced insulation bridged by components General Bridging capacitors Bridging resistors Accessible parts Components in equipment for IT power systems 1.6 Power interface AC power distribution systems Input current Building in equipment, will be evaluated on the end product Voltage limit of hand-held equipment Neutral conductor 1.7 Marking and instructions Pass Power rating See below. Pass Rated voltage(s) or voltage range(s) (V) Vdc, optional Pass Symbol for nature of supply for d.c.... IEC 60417, No. 5031: Pass Rated frequency or frequency range (Hz)...

7 page 6 of 39 Report No.: L7D1808L658 Rated current (ma or A) mA, optional Manufacturer s name/trademark... See page 1. Type/model... See page 1. Symbol of Class II... Other symbols... Additional symbols or marking does not give rise to misunderstanding. Certification marks... CE mark Safety instructions Operation/installation instruction is provided with each unit Short duty cycles Supply voltage adjustment Power outlets on the equipment Fuse identification Wiring terminals Protective earthing and bonding terminals Terminal for a.c. mains supply conductors Controls and indicators Identification, location and marking Colours Symbols according to IEC Markings using figures Isolation of multiple power sources IT power distribution systems Thermostats and other regulating devices Language... Installation instruction and equipment markings are in English. Versions in other languages will be provided with national certificate approval Durability Building in equipment, will be evaluated on the end product Removable parts Replaceable batteries Language Operator access with a tool Equipment for restricted access locations... Pass Pass Pass Pass Pass Pass Pass 2 PROTECTION FROM HAZARDS Pass

8 page 7 of 39 Report No.: L7D1808L Protection from electric shock and energy hazards Class III equipment, the power supply from PC, no electrical insulation is required Protection in operator access areas Access to energized parts Test by inspection... Test with test finger... Test with test pin... Test with test probe Battery compartments Access to ELV wiring Working voltage (V); distance (mm) trough insulation Access to hazardous voltage circuit wiring No hazardous voltage wiring in operator accessible area Energy hazards... No energy hazard in operator access area. The connectors of the equipment below 240VA Manual controls Discharge of capacitors in the primary circuit Time-constant (s); measured voltage (V) Protection in service access areas Protection in restricted access locations Pass Pass 2.2 SELV circuits. Pass General requirements The secondary circuits were tested as SELV. See to Voltages under normal conditions (V) V peak or 60Vd.c. are not exceeded in SELV circuit under normal operation Voltages under fault conditions (V)... Single fault did not cause excessive voltage in accessible SELV circuits. Limits of 71V peak and 120Vd.c. were not exceeded within 0.2s and limits 42.4V peak and 60Vd.c. were not exceeded for longer than 0.2s Separation by double or reinforced insulation (method 1) Separation by earthed screen (method 2) Protection by earthing of the SELV circuit (method 3) Connection of SELV circuits to other circuits... See and Pass Pass Pass Pass

9 page 8 of 39 Report No.: L7D1808L TNV circuits Limits Type of TNV circuits Separation from other circuits and from accessible parts Insulation employed Separation from hazardous voltages Insulation employed Connection of TNV circuits to other circuits Insulation employed Test for operating voltages generated externally 2.4 Limited current circuits General requirements Limit values Circuit capacitance... Frequency (Hz)... : Measured current (ma)... : Measured voltage (V) : Measured capacitance (μf)... : Connection of limited current circuits to other circuits 2.5 Limited power sources Inherently limited output Impedance limited output Overcurrent protective device limited output Regulating network limited output under normal operating and single fault condition Regulating network limited output under normal operating conditions and overcurrent protective device limited output under single fault condition Output voltage (V), output current (A), apparent power (VA)... Current rating of overcurrent protective device (A)

10 page 9 of 39 Report No.: L7D1808L Provisions for earthing and bonding The unit is a Class III equipment Protective earthing Functional earthing Protective earthing and protective bonding conductors General Size of protective earthing conductors Rated current (A), cross-sectional area (mm 2 ), AWG Size of protective bonding conductors Rated current (A), cross-sectional area (mm 2 ), AWG Resistance (Ω) of earthing conductors and their terminations, test current (A) Colour of insulation Terminals General Protective earthing and bonding terminals Rated current (A), type and nominal thread diameter (mm) Separation of the protective earthing conductor from protective bonding conductors Integrity of protective earthing Interconnection of equipment Components in protective earthing conductors and protective bonding conductors Disconnection of protective earth Parts that can be removed by an operator Parts removed during servicing Corrosion resistance Screws for protective bonding Reliance on telecommunication network or cable distribution system 2.7 Overcurrent and earth fault protection in primary circuits The unit is a Class III equipment Basic requirements Instructions when protection relies on building installation.

11 page 10 of 39 Report No.: L7D1808L Faults not covered in Short-circuit backup protection Number and location of protective devices Protection by several devices Warning to service personnel Safety interlocks No safety interlocks provided General principles Protection requirements Inadvertent reactivation Fail-safe operation Moving parts Overriding Switches and relays Contact gaps (mm) Overload test Endurance test Electric strength test (V) Mechanical actuators 2.9 Electrical insulation Properties of insulating materials Humidity conditioning Humidity (%) Temperature ( ) Grade of insulation 2.10 Clearances, creepage distances and distances through insulation General Determination of working voltage Clearances General Clearances in primary circuit Clearances in secondary circuits Measurement of transient voltage levels Creepage distances

12 page 11 of 39 Report No.: L7D1808L658 CTI tests Solid insulation Minimum distance through insulation Thin sheet material Number of layers (pcs)... Electric strength test Printed boards... Distance through insulation Electric strength test for thin sheet insulating material Number of layers (pcs) Wound components... Number of layers (pcs)... : Two wires in contact inside wound component; angle between 45 and 90...: Coated printed boards General Sample preparation and preliminary inspection...: Thermal cycling Thermal ageing Electric strength test Abrasion resistance test... Electric strength test Enclosed and sealed parts... Temperature T 1 =T 2 = T ma T amb +10K ( C) Spacings filled by insulating compound... Electric strength test Component external terminations Insulation with varying dimensions 3 WIRING, CONNECTIONS AND SUPPLY Pass 3.1 General Current rating and overcurrent protection Protection against mechanical damage Securing of internal wiring Insulation of conductors Beads and ceramic insulators

13 page 12 of 39 Report No.: L7D1808L Screws for electrical contact pressure Insulation materials in electrical connections Self-tapping and spaced thread screws Termination of conductors 10 N pull test Sleeving on wiring 3.2 Connection to a.c. mains supplies or d.c. mains supply The equipment is a Class III unit Means of connection Connection to an a.c. mains supply Connection to a d.c. mains supply Multiple supply connections Permanently connected equipment Number of conductors, diameter (mm) of cable and conduits Appliance inlets Power supply cords AC Power supply cords Type... Rated current (A), cross-sectional area (mm 2 ), AWG DC power supply cords Cord anchorages and strain relief Mass of equipment (kg), pull (N)... Longitudinal displacement (mm) Protection against mechanical damage Cord guards D (mm); test mass (g)... Radius of curvature of cord (mm) Supply wiring space 3.3 Wiring terminals for connection of external conductors The equipment is a Class III unit Wiring terminals Connection of non-detachable power supply cords Screw terminals

14 page 13 of 39 Report No.: L7D1808L Conductor sizes to be connected Rated current (A), cord/cable type, cross-sectional area (mm 2 ) Wiring terminal sizes Rated current (A), type and nominal thread diameter (mm) Wiring terminals design Grouping of wiring terminals Stranded wire 3.4 Disconnection from the a.c. mains supply The equipment is a Class III unit General requirement Disconnect devices Permanently connected equipment Parts which remain energized Switches in flexible cords Single-phase equipment and d.c. equipment Three-phase equipment Switches as disconnect devices Plugs as disconnect devices Interconnected equipment Multiple power sources 3.5 Interconnection of equipment Pass General requirements See below. Pass Types of interconnection circuits... Interconnection circuits of SELV through the connectors. No ELV interconnection circuits ELV circuits as interconnection circuits Pass 4 PHYSICAL REQUIREMENTS Pass 4.1 Stability Angle of 10 Test: force (N)... Building in equipment, will be evaluated on the end product.

15 page 14 of 39 Report No.: L7D1808L Mechanical strength General Steady force test, 10 N Steady force test, 30 N Steady force test, 250 N Impact test Fall test Swing test Drop test Stress relief test Cathode ray tubes Picture tube separately certified High pressure lamps Wall or ceiling mounted equipment; force (N)... : 4.3 Design and construction Pass Edges and corners All edges and corners of the exterior enclosure are properly rounded Handles and manual controls; force (N) Adjustable controls Securing of parts Mechanical fixings in such a way designed that they will withstand mechanical stress occurring in normal use Connection of plugs and sockets Direct plug-in equipment Dimensions (mm) of mains plug for direct plug-in Torque and pull test of mains plug for direct plug-in; Torque (Nm); pull (N) Heating elements in earthed equipment Batteries Oil and grease Dust, powders, liquids and gases Containers for liquids or gases Flammable liquids... Quantity of liquid (l)... Flash point ( C) Radiation; type of radiation General Pass Pass

16 page 15 of 39 Report No.: L7D1808L Ionizing radiation Measured radiation (pa/kg)... Measured high-voltage (kv)... Measured focus voltage (kv)... CRT markings Effect of ultraviolet (UV) radiation on materials Part, property, retention after test, flammability classification Human exposure to ultraviolet (UV) radiation Laser (including LEDs) Laser class Other types Protection against hazardous moving parts No moving parts used General Protection in operator access areas Protection in restricted access locations Protection in service access areas 4.5 Thermal requirements Maximum temperatures Building in equipment, will be evaluated on the end product. Normal load condition per Annex L Resistance to abnormal heat 4.6 Openings in enclosures Top and side openings Building in equipment, will be evaluated on the end product. Dimensions (mm) Bottoms of fire enclosures Construction of the bottom Doors or covers in fire enclosures Openings in transportable equipment Adhesives for constructional purposes Conditioning temperature ( )/time (weeks)

17 page 16 of 39 Report No.: L7D1808L Resistance to fire Pass Reducing the risk of ignition and spread of flame See below. Pass Method 1, selection and application of Use of materials with the required Pass components wiring and materials flammability classes. Method 2, application of all of simulated fault condition tests Conditions for a fire enclosure Building in equipment, will be evaluated on the end product Parts requiring a fire enclosure Parts not requiring a fire enclosure Materials See appended table for details. Pass General Pass Materials for fire enclosures Materials for components and other parts outside fire enclosures Materials for components and other parts inside fire enclosures Materials for air filter assemblies Materials used in high-voltage components 5 ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS 5.1 Touch current and protective conductor current General Equipment under test (EUT) Test circuit Application of measuring instrument Test procedure Test measurements Test voltage (V)... Measured touch current (ma)... Max. allowed touch current (ma)... Measured protective conductor current (ma)... : Max. allowed protective conductor current (ma).. : Equipment with touch current exceeding 3.5 ma Touch currents to and from telecommunication networks and cable distribution systems and from telecommunication networks

18 page 17 of 39 Report No.: L7D1808L Limitation of the touch current to a telecommunication network and a cable distribution system Test voltage (V)... Measured current (ma)... Max. allowed current (ma) Summation of touch currents from telecommunication networks Electric strength General Test procedure 5.3 Abnormal operating and fault conditions Protection against overload and abnormal operation Motors Transformers Functional insulation Electromechanical components Simulation of faults Unattended equipment Compliance criteria for abnormal operating and fault conditions 6 CONNECTION TO TELECOMMUNICATION NETWORKS 6.1 Protection of telecommunication network service personnel, and users of other equipment connected to the network, from hazards in the equipment Protection from hazardous voltages Separation of the telecommunication network from earth Requirements Test voltage (V)... Current in the test circuit (ma) Exclusions Protection of equipment users from overvoltages on telecommunication networks Separation requirements Electric strength test procedure

19 page 18 of 39 Report No.: L7D1808L Impulse test Steady-state test Compliance criteria 6.3 Protection of telecommunication wiring system from overheating Max. output current (A)... Current limiting method... 7 CONNECTION TO CABLE DISTRIBUTION SYSTEMS 7.1 Protection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment 7.2 Protection of equipment users from overvoltages on the cable distribution system 7.3 Insulation between primary circuits and cable distribution systems General Voltage surge test Impulse test

20 page 19 of 39 Report No.: L7D1808L658 A ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE A.1 Flammability test for fire enclosures of movable equipment having a total mass exceeding 18 kg, and of stationary equipment (see ) A.1.1 Samples Wall thickness (mm)... A.1.2 Conditioning of samples; temperature ( C)... A.1.3 Mounting of samples... A.1.4 Test flame A.1.5 Test procedure A.1.6 Compliance criteria Sample 1 burning time (s)... Sample 2 burning time (s)... Sample 3 burning time (s)... A.2 Flammability test for fire enclosures of movable equipment having a total mass not exceeding 18 kg, and for material and components located inside fire enclosures (see and ) A.2.1 Samples Wall thickness (mm)... A.2.2 Conditioning of samples... A.2.3 Mounting of samples... A.2.4 Test flame A.2.5 Test procedure A.2.6 Compliance criteria Sample 1 burning time (s)... Sample 2 burning time (s)... Sample 3 burning time (s)... A.2.7 Alternative test acc. to IEC , cl. 4, 8 Sample 1 burning time (s)... Sample 2 burning time (s)... Sample 3 burning time (s)... A.3 Hot flaming oil test (see 4.6.2) A.3.1 Mounting of samples... A.3.2 Test procedure A.3.3 Compliance criterion...

21 page 20 of 39 Report No.: L7D1808L658 B ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see and 5.3.2) B.1 General requirements Position... Manufacturer... Type... Rated values... B.2 Test conditions B.3 Maximum temperatures B.4 Running overload test B.5 Locked-rotor overload test Test duration (days)... Electric strength test: test voltage (V)... B.6 Running overload test for DC motors in secondary circuits B.7 Locked-rotor overload test for DC motors in secondary circuits B.7.1 Test procedure B.7.2 Alternative test procedure; test time (h)... B.7.3 Electric strength test B.8 Test for motors with capacitors B.9 Test for three-phase motors B.10 Test for series motors Operating voltage (V)... C ANNEX C, TRANSFORMERS (see and 5.3.3) Position... Manufacturer... Type... Rated values... Method of protection... C.1 Overload test C.2 Insulation Protection from displacement of windings

22 page 21 of 39 Report No.: L7D1808L658 D ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS D.1 Measuring instrument D.2 Alternative measuring instrument E ANNEX E, TEMPERATURE RISE OF A WINDING F ANNEX F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES (see 2.10) G ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM CLEARANCES G.1 Summary of the procedure for determining minimum clearances G.2 Determination of mains transient voltage (V)... G.2.1 AC mains supply G.2.2 DC mains supply G.3 Determination of telecommunication network transient voltage (V)... G.4 Determination of required withstand voltage (V)... G.5 Measurement of transient levels (V)... G.6 Determination of minimum clearances... H ANNEX H, IONIZING RADIATION (see ) J ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see ) Metal used... K ANNEX K, THERMAL CONTROLS (see and 5.3.7) K.1 Making and breaking capacity K.2 Thermostat reliability; operating voltage (V)... K.3 Thermostat endurance test; operating voltage (V)... K.4 Temperature limiter endurance; operating voltage (V)... K.5 Thermal cut-out reliability K.6 Stability of operation L ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL BUSINESS EQUIPMENT (see and 4.5.1) Pass

23 page 22 of 39 Report No.: L7D1808L658 L.1 Typewriters L.2 Adding machines and cash registers L.3 Erasers L.4 Pencil sharpeners L.5 Duplicators and copy machines L.6 Motor-operated files L.7 Other business equipment Considered. Pass M ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1) M.1 Introduction M.2 Method A M.3 Method B M.3.1 Ringing signal M Frequency (Hz)... M Voltage (V)... M Cadence; time (s), voltage (V)... M Single fault current (ma)... M.3.2 Tripping device and monitoring voltage... M Conditions for use of a tripping device or a monitoring voltage M Tripping device M Monitoring voltage (V)... N ANNEX N, IMPULSE TEST GENERATORS (see , , and clause G.5) N.1 ITU-T impulse test generators N.2 IEC impulse test generator P ANNEX P, NORMATIVE REFERENCES Q ANNEX Q, BIBLIOGRAPHY

24 page 23 of 39 Report No.: L7D1808L658 R ANNEX R, EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL PROGRAMMES R.1 Minimum separation distances for unpopulated coated printed boards (see ) R.2 Reduced clearances (see ) S ANNEX S, PROCEDURE FOR IMPULSE TESTING (see ) S.1 Test equipment S.2 Test procedure S.3 Examples of waveforms during impulse testing T ANNEX T, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER See separate test report (reference to standard clause 1.1.2) U ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED INSULATION (see ). Separate test report V ANNEX V, AC POWER DISTRIBUTION SYSTEMAS (see 16.1) V.1 Introduction V.2 TN power distribution systems W ANNEX W, SUMMATION OF TOUCH CURRENTS W.1 Touch current from electronic circuits W.1.2 Earthed circuits W.2 Interconnection of several equipments W.2.1 Isolation W.2.2 Common return, isolated from earth W.2.3 Common return, connected to protective earth X ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS (see clause C.1) X.1 Determination of maximum input current X.2 Overload test procedure Y ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see ) Y.1 Test apparatus

25 page 24 of 39 Report No.: L7D1808L658 Y.2 Mounting of test samples Y.3 Carbon-arc light-exposure apparatus Y.4 Xenon-arc light-exposure apparatus

26 page 25 of 39 Report No.: L7D1808L TABLE: list of critical components Pass object/part No. manufacturer/ trademark type/model technical data standard mark(s) of conformity PCB Min. V-1, 105 C UL 94 UL * Additional testing and evaluation may be required based on auditing agency s discretion.

27 page 26 of 39 Report No.: L7D1808L TABLE: electrical data (in normal conditions) fuse # I rated (A) U (V) P (W) I (ma) I fuse (ma) condition/status Comments: TABLE: max. V, A, VA test Voltage (rated) (V) Current (rated) (A) Voltage (max.) (V) Current (max.) (A) VA (max.) (VA) Note(s): TABLE: discharge test Condition τcalculated (s) τmeasured (s) tu 0V (s) Comments Note(s): TABLE: Hazardous voltage measurement Transformer Location max. Voltage V peak V d.c. Voltage Limitation Componet Note(s): TABLE: SEL voltage measurement Location Voltage measured (V) Comments Note(s): TABLE: limited current circuit measurement Location Voltage (V) Current (Ma) Freq. (khz) Limit (ma) Comments

28 page 27 of 39 Report No.: L7D1808L658 Note(s): 2.5 TABLE: limited power source measurement Limits Measured Verdict Test for Battery Pack According to Table 2B ( normal condition) current (in A) 8 Apparent power (in VA) According to Table 2B (single fault condition current (in A) 8 Apparent power (in VA) Note(s): TABLE: ground continue test Location Resistance measured(mω) Comments Note(s): TABLE: working voltage measurement Location Resistance measured(mω) Comments Note(s): and TABLE: clearance and creepage distance measurements clearance cl and creepage distance dcr at/of: Up (V) U r.m.s. (V) required cl (mm) cl (mm) required dcr (mm) dcr (mm) Note(s) TABLE: distance through insulation measurements distance through insulation di at/of: U r.m.s. (V) test voltage (V) required di (mm) di (mm)

29 page 28 of 39 Report No.: L7D1808L658 Note(s): TABLE: maximum temperatures test voltage (V)... t amb1 (ºC)... t amb2 (ºC)... Maximum temperature T of part/at: T (ºC) allowed T max (ºC) Test for Unit Test voltage (A) (B) temperature T of winding: R1 (Ω) R2 (Ω) dt (ºK) allowed T max (ºC) insulation class Note(s): 1) All values for T ( ) are re-calculated from Tamb respectively. 2) The maximum ambient temperatures specified by manufacturer is 25 (Tma) TABLE: ball pressure test of thermoplastics parts allowed impression diameter (mm)...: 2 mm part: test temperature (ºC) impression diameter (mm) 4.6.1, TABLE: Enclosure openings Location Size(mm) Comments

30 page 29 of 39 Report No.: L7D1808L658 Top None -- Note(s): 4.7 TABLE: resistance to fire part: Manufacturer of material Type of material Thickness (mm) Flammability class Note(s): TABLE: touch current measurement Condition L terminal A (ma) N terminal A (ma) Limit Comments Note(s): 5.2 TABLE: electric strength tests and impulse tests Test voltage applied between: Test voltage (V) Breakdown 5.3 TABLE: fault condition tests No. ambient temperature (ºC)...: model/type of power supply...: manufacturer of power supply...: rated markings of power supply...: component No. fault test voltage (V) test time fuse No. fuse current (A) result

31 page 30 of 39 Report No.: L7D1808L658 Note(s) CENELEC COMMON MODIFICATIONS [C], SPECIAL NATIONAL CONDITIONS [S] AND A-DEVIATIONS (NATIONAL DEVIATIONS) [A] (EN :2001, Annex ZB and Annex ZC) General C: Delete all the "country" notes in the reference Deleted. document according to the following list: Note Note Note Note Note Note Note Note Note 2,7, Note Note Note Note Note Note1, Note Note1, Note Note Note Note Note Note Note 7 Note4 7.1 Note G2.1 Note1,2 Annex H Note S (DK): Certain types of Class I appliances (see ) may be provided with a plug not establishing earthing conditions when inserted into Danish socket-outlets A (SE, Ordinance 1990:944 and CH, Ordinance on environmentally hazardous substances SR , Annex 3.2, Mercury): Add NOTE -Switches containing mercury such as thermostats, relays and level controllers are not allowed S (NO): Due to the IT power system used (see annex V, Fig. V.7), capacitors are required to be rated for the applicable line-to-line voltage (230 V) S (FI, NO, SE): CLASS I PLUGGABLE EQUIPMENT TYPE A intended for connection to other equipment or a network shall, if safety relies on connection to protective earth or if surge suppressors are connected between the network terminals and accessible parts, have a marking stating that the equipment must be connected to an earthed mains socket-outlet. No direct connection to the mains supply. No such switch. Class III equipment. Class III equipment. P P The marking text in the applicable countries shall be as follows: FI: "Laite on liitettava suojamaadoituskoskettimilla varustettuun pistorasiaan" Class III equipment. NO: "Apparatet ma tilkoples jordet stikkontakt" Class III equipment. SE: "Apparaten skall anslutas till jordat uttag" Class III equipment.

32 page 31 of 39 Report No.: L7D1808L658 A (DK, Heavy Current Regulations): Supply cords of class I equipment, which is delivered without a plug, must be provided with a visible tag with the following text: Vigtigt! Lederen med gron/gul isolation ma kun tilsluttes en klemme market Class III equipment. If essential for the safety of the equipment, the tag must in addition be provided with a diagram which shows the connection of the other conductors, or be provided with the following text: "For tilslutning af de ovrige ledere, se medfolgende instalationsvejledning." S (DK): Socket-outlets for providing power to other equipment shall be in accordance with the Heavy Current Regulations, Section D1, Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a, when used on Class I equipment. For stationary equipment the socket-outlet shall be in accordance with Standard Sheet DK 1-1b or DK 1-5a A (DK, Heavy Current Regulations): CLASS II EQUIPMENT shall not be fitted with socketoutlets for providing power to other equipment A (DE, Gesetz uber technische Arbeitsmittel (Geratesicherheitsgesetz) [Law on technical labour equipment {Equipment safety law}], of 23rd October 1992, Article 3, 3rd paragraph, 2nd sentence, together with the "Allgemeine Verwaltungsvorschrift zur Durchfuhrung des Zweiten Abschnitts des Geratesicherheitsgesetzes" [General administrative regulation on the execution of the Second Section of the Equipment safety law], of 10th January 1996, article 2, 4th paragraph item 2): Directions for use with rules to prevent certain hazards for (among others) maintenance of the technical labour equipment, also for imported technical labour equipment shall be written in the German language. NOTE: Of this requirement, rules for use even only by service personnel are not exempted A (CH, Ordinance on environmentally hazardous substances SR ): Annex 4.10 of SR applies for batteries. No socket-outlets. Class III equipment. Shall be evaluated during national approval.

33 page 32 of 39 Report No.: L7D1808L658 A (DE, Regulation on protection against hazards by X-ray, of 8th January 1987, Article 5 [Operation of X-ray emission source], clauses 1 to 4): a) A licence is required by those who operate an X-ray emission source. b) A licence in accordance with Cl. 1 is not required by those who operate an X-ray emission source on which the electron acceleration voltage does not exceed 20 kv if 1) the local dose rate at a distance of 0,1 m from the surface does not exceed 1 μsv/h and 2) it is adequately indicated on the X-ray emission source that i) X-rays are generated and ii) the electron acceleration voltage must not exceed the maximum value stipulated by the manufacturer or importer. c) A licence in accordance with Cl. 1 is also not required by persons who operate an X-ray emission source on which the electron acceleration voltage exceeds 20 kv if 1) the X-ray emission source has been granted a type approval and 2) it is adequately indicated on the X-ray emission source that i) X-rays are generated ii) the device stipulated by the manufacturer or importer guarantees that the maximum permissible local dose rate in accordance with the type approval is not exceeded and iii) the electron acceleration voltage must not exceed the maximum value stipulated by the manufacturer or importer. d) Furthermore, a licence in accordance with Cl. 1 is also not required by persons who operate X-ray emission sources on which the electron acceleration voltage does not exceed 30 kv if 1) the X-rays are generated only by intrinsically safe CRTs complying with Enclosure III, No. 6, 2) the values stipulated in accordance with Enclosure III, No. 6.2 are limited by technical measures and specified in the device and 3) it is adequately indicated on the X-ray emission source that the X-rays generated are adequately screened by the intrinsically safe CRT S (NO): Requirements according to this annex, and apply S (NO): Requirements according to this annex, apply and S (NO): Requirements according to this annex, and apply S (GB): The current rating of the circuit shall be taken as 13 A, not 16 A. This national difference was deleted by A11 of EN No TNV circuits. No TNV circuits. No TNV circuits. Class III equipment.

34 page 33 of 39 Report No.: L7D1808L C: Replace the subclause as follows: Basic requirements To protect against excessive current, shortcircuits and earth faults in PRIMARY CIRCUITS, protective devices shall be included either as integral parts of the equipment or as parts of the building installation, subject to the following, a), b) and c): a) except as detailed in b) and c), protective devices necessary to comply with the requirements of 5.3 shall be included as parts of the equipment; b) for components in series with the mains input to the equipment such as the supply cord, appliance coupler, r.f.i. filter and switch, shortcircuit and earth fault protection may be provided by protective devices in the building installation; c) it is permitted for PLUGGABLE EQUIPMENT TYPE B or PERMANENTLY CONNECTED EQUIPMENT, to rely on dedicated overcurrent and short-circuit protection in the building installation, provided that the means of protection, e.g. fuses or circuit breakers, is fully specified in the installation instructions. If reliance is placed on protection in the building installation, the installation instructions shall so state, except that for PLUGGABLE EQUIPMENT TYPE A the building installation shall be regarded as providing protection in accordance with the rating of the wall socket outlet. S (GB): To protect against excessive currents and short-circuits in the PRIMARY CIRCUIT OF DIRECT PLUG-IN EQUIPMENT, protective device shall be included as integral parts of the DIRECT PLUGIN EQUIPMENT. Replaced. Not direct plug-in equipment C: Void. Declared C: Replace in the first line "(see also 1.4.7)" by "(see also 1.4.8)". Replaced S (NO): Due to the IT power distribution system used (see annex V, Fig. V.7), the A.C. MAINS SUPPLY voltage is considered to be equal to the line-to-line voltage and will remain at 230 V in case of a single earth fault No direct connection to the mains supply.

35 page 34 of 39 Report No.: L7D1808L S (CH): Supply cords of equipment having a RATED CURRENT not exceeding 10 A shall be provided with a plug complying with SEV 1011 or IEC and one of the following dimension sheets: SEV , Plug type 15, 3P+N+PE 250/400 V, 10 A SEV , Plug type 11, L+N 250 V, 10 A SEV , Plug type 12, L+N+PE 250 V, 10 A In general, EN applies for plugs for currents exceeding 10 A. However, a 16 A plug and socket-outlet system is being introduced in Switzerland, the plugs of which are according to the following dimension sheets, published in February 1998: SEV , Plug type 25, 3L+N+PE 230/400 V, 16 A SEV , Plug type 21, L+N 250 V, 16 A SEV , Plug type 23, L+N+PE 250 V, 16 A No power supply cord provided. S (DK): Supply cords of single-phase equipment having a rated current not exceeding 13 A shall be provided with a plug according to the Heavy Current Regulations, Section D1. CLASS I EQUIPMENT provided with socket-outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with standard sheet DK 2-1a or DK 2-5a. If ply-phase equipment and single-phase equipment having a RATED CURRENT exceeding 13 A is provided with a supply cord with a plug, this plug shall be in accordance with the Heavy Current Regulations, Section D1 or EN S (ES): Supply cords of single-phase equipment having a rated current not exceeding 10 A shall be provided with a plug according to UNE 20315:1994. Supply cords of single-phase equipment having a rated current not exceeding 2,5 A shall be provided with a plug according to UNE-EN 50075:1993. CLASS I EQUIPMENT provided with socket-outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules, shall be provided with a plug in accordance with standard UNE 20315:1994. If poly-phase equipment is provided with a supply cord with a plug, this plug shall be in accordance with UNE-EN No power supply cord provided. No power supply cord provided.

36 page 35 of 39 Report No.: L7D1808L658 S (GB): Apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to BS 1363 by means of that flexible cable or cord and plug, shall be fitted with a 'standard plug' in accordance with Statutory Instrument 1768:1994 The Plugs and Socket etc. (Safety) Regulations 1994, unless exempted by those regulations. NOTE 'Standard plug' is defined in SI 1768:1994 and essentially means an approved plug conforming to BS 1363 or an approved conversion plug. S (IE): Apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to I.S. 411 by means of that flexible cable or cord and plug, shall be fitted with a 13 A plug in accordance with Statutory Instrument 525:1997 National Standards Authority of Ireland (section 28) (13 A Plugs and Conversion Adaptors for Domestic Use) Regulations C: Delete Note 1 and in Table 3A, delete the conduit sizes in parentheses C: Replace "60245 IEC 53" by "H05 RR-F"; "60227 IEC 52" by "H03 VV-F or H03 VVH2-F"; "60227 IEC 53" by "H05 VV-F or H05 VVH2-F2". In Table 3B, replace the first four lines by the following: Up to and including 6 0,751) Over 6 up to and including 10 (0,75)2) 1,0 Over 10 up to and including 16 (1,0)3) 1,5 In the Conditions applicable to Table 3B delete the words "in some countries" in condition 1). In Note 1, applicable to Table 3B, delete the second sentence S (GB): A power supply cord with conductor of 1,25 mm2 is allowed for equipment with a rated current over 10 A and up to and including 13 A C: In table 3D, delete the fourth line: conductor sizes for 10 to 13 A, and replace with the following: Deleted. N/A "Over 10 up to and including 16 1,5 to 2,5 1,5 to 4" Delete the fifth line: conductor sizes for 13 to 16 A. No power supply cord provided. No power supply cord provided. Deleted. Replaced. No power cord provided. Deleted.

37 page 36 of 39 Report No.: L7D1808L S (GB): The range of conductor sizes of flexible cords to be accepted by terminals for equipment with a RATED CURRENT of over 10 A up to and including 13 A is: - 1,25 mm2 to 1,5 mm2 nominal cross-sectional area S (GB): The torque test is performed using a socket outlet complying with BS 1363 and the plug part of DIRECT PLUG-IN EQUIPMENT shall be assessed to BS 1363: Part 1, 12.1, 12.2, 12.3, 12.9, 12.11, 12.12, and 12.17, except that the test of is performed at not less than 125 C. S (IE): DIRECT PLUG-IN EQUIPMENT is known as plug similar devices. Such devices shall comply with Statutory Instrument 526:1997 National Standards Authority of Ireland (Section 28) (Electrical plugs, plug similar devices and sockets for domestic use) Regulations, C: Add the following note: NOTE Attention is drawn to 1999/519/EC: Council Recommendation on the limitation of exposure of the general public to electromagnetic fields 0 Hz to 300 GHz. Standards taking into account this recommendation are currently under development. No power supply cord provided. Not direct plug-in equipment. Not direct plug-in equipment. Added.

38 page 37 of 39 Report No.: L7D1808L S (FI, NO, SE): Add the following text between the first and second paragraph: If this insulation is solid, including insulation forming part of a component, it shall at least consist of either - two layers of thin sheet material, each of which shall pass the electric strength test below, or - one layer having a distance through insulation of at least 0,4 mm, which shall pass the electric strength test below. If this insulation forms part of a semiconductor component (e.g. an optocoupler), there is no distance through insulation requirement for the insulation consisting of an insulating compound completely filling the casing, so that CLEARANCES AND CREEPAGE DISTANCES do not exist, if the component passes the electric strength test in accordance with the compliance clause below and in addition - passes the tests and inspection criteria of with an electric strength test of 1,5 kv multiplied by 1,6 (the electric strength test of shall be performed using 1,5 kv), and - is subject to ROUTINGE TESTING for electric strength during manufacturing, using a test voltage of 1,5 kv. It is permitted to bridge this insulation with a capacitor complying with EN :1994, subclass Y2. A capacitor classified Y3 according to EN :1994, may bridge this insulation under the following conditions: - the insulation requirements are satisfied by having a capacitor classified Y3 as defined by EN , which in addition to the Y3 testing, is tested with an impulse test of 2,5 kv defined in EN 60950:2000, ; - the additional testing shall be performed on all the test specimens as described in EN ; - the impulse test of 2,5 kv is to be performed before the endurance test in EN , in the sequence of tests as described in EN S (FI, NO, SE): The exclusions are applicable for PERMANENTLY CONNECTED EQUIPMENT and PLUGGABLE EQUIPMENT TYPE B and equipment intended to be used in a RESTRICTED ACCESS LOCATION where equipotential bonding has been applied, e.g. in a telecommunication centre, and which has provision for a permanently connected PROTECTIVE EARTHING CONDUCTOR and is provided with instructions for the installation of that conductor by a service person. No TNV circuits. No TNV circuits.

39 page 38 of 39 Report No.: L7D1808L S (FI, NO, SE): Requirements according to this annex, and apply with the term TELECOMMUNICATION NETWORK in being replaced by the term CABLE DISTRIBUTION SYSTEM. Not connect to cable distribution system. G.2.1 S (NO): Due to the IT power distribution system used (see annex V, Fig. V.7), the A.C. MAINS SUPPLY voltage is considered to be equal to the line-to-line voltage, and will remain at 230 V in case of a single earth fault. No direct connection to the mains supply. Annex H C: Replace the last paragraph of this annex by: At any point 10 cm from the surface of the operator access area, the dose rate shall not exceed 1 μsv/h (0,1 mr/h) (see note). Account is taken of the background level. Replace the notes as follows: NOTE These values appear in Directive 96/29/Euratom. Delete Note 2. No CRT. Annex P C: Replace the text of this annex by: See annex ZA. Replaced. P Annex Q Annex ZA C: Replace the title of IEC by "Protection of persons and equipment by enclosures Probes for verification". Add the following notes for the standards indicated: IEC NOTE Harmonized as EN (Series) (not modified) IEC NOTE Harmonized as HD S4:2000 (modified) IEC NOTE Harmonized as EN 60529:1991 (not modified) IEC NOTE Harmonized as EN 61032:1998 (not modified) IEC NOTE Harmonized as EN 61140:2001 (not modified) ITU-T Recommendation K.31 NOTE in Europe, the suggested document is EN C: NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH THEIR RELEVANT EUROPEAN PUBLICATIONS This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies (including amendments). NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. IEC IEC EN 60065: corr. June 1999 IEC (mod):1998 EN 60073:1996 IEC 60073:1996 HD 566 S1:1990 IEC 60085:1984 HD 214 S2:1980 IEC 60112:1979 HD S1:1992 IEC :1990 HD 21 1) Series IEC (mod) Series HD 22 2) Series IEC (mod) Series P

40 page 39 of 39 Report No.: L7D1808L658 EN Series IEC Series EN :1997 IEC :1997 EN Series IEC (mod) Series HD S2:199 IEC (mod):1993 HD S2:1996 IEC (mod):1992 3) EN :1994 4) IEC : A2: A3: A4:2001 EN IEC HD S1: corr. Nov IEC (mod):1992 EN :1994 IEC :1991 EN :2001 IEC :2000 IEC :1995 IEC :1995 IEC :2000 IEC :2000 EN :1999 IEC :1999 EN :1999 IEC :1999 EN :2000 IEC :1999 (mod) EN : corr. Febr IEC :1993 A11: corr. July 1997 EN :2000 IEC :2000 IEC :1999 EN :1996 IEC :1996 EN :1996 IEC :1996 EN :1996 IEC :1996 IEC :1987 EN 60990:1999 IEC 60990:1999 _ IEC :2000 EN 61965:2001 IEC 61965:2000 EN ISO 178:1996 ISO 178:1993 EN ISO 179 Series ISO 179 Series EN ISO 180:2000 ISO 180:1993 ISO 261:1998 ISO 262:1998 EN ISO 527 Series ISO 527 Series ISO 386:1984 EN ISO 4892 Series ISO 4892 Series ISO 7000:1989 EN ISO 8256:1996 ISO 8256:1990 ISO 9772:1994 EN ISO 9773:1998 ISO 9773:1998 ITU-T:1988 Recommendation K.17 ITU-T:2000 Recommendation K.21

41 Page 1 Report No.: L7D1808L658 Appendix - Photo

42 Page 2 Report No.: L7D1808L658 Appendix - Photo

43 Page 3 Report No.: L7D1808L658 Appendix - Photo