Page 2 of 73 Report No.: Copy of marking plate:

Transcription

1

2

3

4 age 2 of 73 Report No.: Copy of marking plate: Note: The above labels are draft of artwork for marking plates pending approval by National Certification Bodies and it shall not be affixed to products prior to such approval.

5 age 3 of 73 Report No.: Copy of marking plate: Note: The above labels are draft of artwork for marking plates pending approval by National Certification Bodies and it shall not be affixed to products prior to such approval.

6 age 4 of 73 Report No.: Summary of testing: The equipment under test (EUT) has been evaluated at maximum ambient temperature of +35 C according to the manufacturer specified. The load conditions used during testing: - Highest load according to for this equipment is reading/writing between HDD and memory card, maximum brightness and contrast of LED back-light circuit, play a video CD, maximum valume of speakers, RJ45 transmission signal to other C or server, add dummy loads of 2.5W for each USB ports, charging an empty battery pack. - Equipment with the following configuration: a. CU: Intel enryn Core 2 Duo series processor, 2.4 GHz (provide for main board /N: MS-17311, MS and MS-17331) or Intel Arrandale Core i5 processor, type M520, 2.4 GHz (provide for main board /N: MS-17361) b. Memory: DDR2 SDRAM 4 GB x 2 The USB ports were complied with sub-clause 2.5 limited power source.

7 age 5 of 73 Report No.: articulars: test item vs. test requirements Equipment mobility...: Transportable equipment Operating condition...: Continuous Mains supply tolerance (%)...: No direct mains connection Tested for IT power systems...: No IT testing, phase-phase voltage (V)...: Class of equipment...: III Mass of equipment (kg)...: 2.5 rotection against ingress of water...: IX0 Test case verdicts Test case does not apply to the test object..: Test item does meet the requirement...: (ass) Test item does not meet the requirement...: F(ail) Testing Date of receipt of test item...: November, 2009 Date(s) of performance of test...: November, 2009 General remarks This report is not valid as a CB Test Report unless appended by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02. The test result presented in this report relate only to the object(s) tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(see Enclosure #)" refers to additional information appended to the report. "(see appended table)" refers to a table appended to the report. Throughout this report a point is used as the decimal separator. Comments: Summary of compliance with National Differences (for explanation of codes see below): EU Group Differences, EU Special National Conditions, EU A-Deviations, AR, AT, AU, BE, CA, CH, CN, CZ, DE, DK, FR, GB, GR, HU, IL, IN, IT, KE, KR, MY, NL, L, SG, SI, SK, US. AR=Argentina, AT=Austria, AU=Australia, BE=Belgium, CA=Canada, CH=Switzerland, CN=China, CZ=Czech Republic, DE=Germany, DK=Denmark, FI=Finland, FR=France, GB=United Kingdom, GR=Greece, HU=Hungary, IL=Israel, IN=India, IT=Italy, KE=Kenya, KR=Korea, MY=Malaysia, NL=The Netherlands, NO=Norway, L=oland, SE=Sweden, SG=Singapore, SI=Slovenia, SK=Slovakia, US=United States of America. For National Differences see end of this test report. Factory(ies): 1. MSI Computer (Shenzhen) Co., Ltd. Longma Information Technology, Industrial ark, Tangtou Village, Shiyan Town, Baoan District, Shenzhen, Guangdong ,.R. China 2. MSI ELECTRONICS (KUNSHAN) CO., LTD. 88E QIANJIN Rd., Kunshan City, Jiangsu ,.R. China

8 age 6 of 73 Report No.: Micro-Star Int l Co., Ltd. 69, Li-De St., Chung Ho City, Taipei Hsien 235 Taiwan The manufacturer's declaration, that the samples tested represent the products from each factory, is available. Definition of variables: Variable: Range of variable: Content: X 0-9, a-z, A-Z or blank Marketing purpose, no technical differences

9 age 7 of 73 Report No.: General product information: The equipment under test (EUT) is a Notebook ersonal Computer for general office use. The equipment has five alternative sources of main board, the construction difference as below list: Summary of construction: Model MS-173XXXX (X= 0-9, a-z, A-Z or blank) Construction A B C D Input rating: 19Vdc, 3.42A 19Vdc, 3.42A 19Vdc, 4.74A 19Vdc, 3.42A Enclosure type: CU: A (original) Intel enryn Core 2 Duo series processor, 2.4 GHz A (original) Intel enryn Core 2 Duo series processor, 2.4 GHz B (alternative) Intel enryn Core 2 Duo series processor, 2.4 GHz C (alternative) Intel Arrandale Core i5 processor, type M520, 2.4 GHz Main board /N: MS MS MS MS USB board /N MS-1731A MS-1734A MS-1733A MS-1736A - HDMI ports USB ports E-SATA ports RJ-11 ports Modem card TV tuner card H.D.D O.D.D Audio ports VGA ports RJ-45 ports Card reader Express card slot Note(s): 1. The enclosure type B and C are similar to enclosure type A except for the number of I/O prots. Engineering Considerations: The equipment is supplied from an approved power adaptor or battery pack that are provide SELV circuit and energy level below 240VA. The sources of LCD panel used in the equipment is supplied from LED backlight unit, the LCD panel supply voltage is less than 42.4 Vdc which is considered as SELV circuit, therefore, no further testing consideration in SELV circuit to be necessary.

10 age 8 of 73 Report No.: The following accessible locations are compliance with Limited ower Sources ( see subclause 2.5): USB port. For the EUT with construction C: The following terminals to be connected to a Cable Distribution System were investigated to Clause 7: TV-tuner antenna connector The equipment provides one TV tuner module as optional function that considered as a multimedia equipment under the IEC Guide 112. Therefore, the surge test, insulation resistance test and dielectric strength test were performed according to sub-clauses 10.1 and 10.3 of IEC 60065: 2001 as following test condition: - Surge test performed from AC mains supply terminal of external power adapter to antenna connector of TV tuner with 50 discharges at a maximum rate of 12 per minute, from a 1nF capacitor charged to 10kV. - After the test, the insulation resistance greater then 4 MΩ at 500Vdc and subjected to dielectric strength test at test voltage 4240 V d.c. Due to fulfilled the following considerations for the equipment, the separation requirements and tests according to clause 6.2 do not apply to the cable distribution system. - The circuit of cable distribution system is considered as TNV-1 circuit. - The common sides or earthed side of the circuit are connected to the screen of the coaxial cable through an antenna connector of tuner and to all accessible parts and circuits (SELV and accessible metal parts). - The screen of the coaxial cable is intended to be connected to earth in the building installation. (The statements for earthing connection during installation were provided in user s manual). The similar approach for CB-Scheme testing according to IEC :2005, covering Germany, USA and Canada. However, in compliance with above mention requirement for other CB countries has to be verified during national mark approval. Additional Information: This report contains national differences as the class III equipment itself and is subject of this CB report. Destination countries should investigate this matter for external adapter while the equipment is submitted for national approval. The Label in Copy of marking plate is a draft of an artwork pending approval by National Certification Bodies and it shall not be affixed to products prior to such an approval. Markings and Instructions: The user s manual provided the following information regarding: - Specification and operations - Maximum ambient temperature - The statement for the screen of the coaxial cable is intended to be connected to earth in the building installation during installation is provided in user s manual The following statement is provided in user s manual. (See subclause ) for the following replaceable batteries: a rechargable Lithium ion battery pcak and a non-rechargable lithium type RTC battery. CAUTION Danger of explosion if battery is replaced by an incorrect type. Replace only with the same or equivalent type recommended by the equipment manufacturer.

11 age 9 of 73 Report No.: Discard used batteries according to manufacturer s instructions The product also marked with: (IEC ) for the stand-by condition. (See subclause ): it is marked on stand-by type switch button.

12 age 10 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict 1 GENERAL 1.5 Components General See below. Comply with IEC or relevant component standard See appended table Evaluation and testing of components Components certified to IEC standards and/or their harmonized standards, are used within their ratings and are checked for correct application. Non-certified components are checked for correct application, used within their ratings, tested as part of the equipment and subjected to applicable tests of the component standard Thermal controls Transformers No insulation transformer Interconnecting cables Capacitors in primary circuits...: Double insulation or reinforced insulation bridged by components General Bridging capacitors Bridging resistors Accessible parts Components in equipment for IT power systems 1.6 ower interface AC power distribution systems Equipment is not directly connected to the AC mains supply Input current See summary of testing for load condition and appended table for test results Voltage limit of hand-held equipment Neutral conductor 1.7 Marking and instructions

13 age 11 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict ower rating All relevant markings are provided on a label that is glued on the bottom enclosure. Rated voltage(s) or voltage range(s) (V)...: See copy of marking plate. (No direct connection to mains supply) Symbol for nature of supply, for d.c. only...: d.c. symbol used. Rated frequency or rated frequency range (Hz)..: No direct connection to AC mains supply. Rated current (ma or A)...: See copy of marking plate. (No direct connection to mains supply) Manufacturer s name or trademark or identification mark...: See copy of marking plates. Type/model or type reference...: See copy of marking plates. Symbol for Class II equipment only...: Class III equipment. Other symbols...: Additional symbols or markings do not give rise to misunderstanding. Certification marks...: See copy of marking plates Safety instructions See General product information - Markings and Instructions Short duty cycles Supply voltage adjustment...: Methods and means of adjustment; reference to installation instructions...: ower outlets on the equipment...: Fuse identification (marking, special fusing characteristics, cross-reference)...: Wiring terminals rotective earthing and bonding terminals...: Terminal for a.c. mains supply conductors Terminals for d.c. mains supply conductors Controls and indicators See below Identification, location and marking...: The function of indicators and controls is clearly identified Colours...: Colors are used and safety is not involved.

14 age 12 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict Symbols according to IEC : See General product information - Markings and Instructions Markings using figures...: Isolation of multiple power sources...: IT power distribution systems Thermostats and other regulating devices Language(s)...: Marking plate and user s manual are in English. Versions in other languages will be provided when national certificate approval Durability Compliance. Marking is durable and legible Removable parts The required marking is not placed on removable parts Replaceable batteries See General product information - Markings and Instructions Language(s)...: English Operator access with a tool...: No operator access area with tool Equipment for restricted access locations...: Use of equipment not limited to restricted access locations. 2 ROTECTION FROM HAZARDS 2.1 rotection from electric shock and energy hazards rotection in operator access areas Unless otherwise indicated in , all parts are safe to access by operator Access to energized parts See below. Test by inspection...: The notebook C is supplied from an approved power adaptor or battery pack that provides only SELV. Test with test finger...: No access with test finger to any parts with only basic insulation to TNV-3. Test with test pin...: Only SELV and LCC circuit provided.

15 age 13 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict Test with test probe...: The test probe cannot touch pins of connector (RJ-11) of TNV-3 circuit through any seams within the appliance Battery compartments...: TNV circuits are not accessible when replacing battery pack and RTC battery Access to ELV wiring Working voltage (Vpeak or Vrms); minimum distance (mm) through insulation Access to hazardous voltage circuit wiring Energy hazards...: No energy hazard in operator access area. The connectors on the backside of the equipment below 240VA Manual controls Discharge of capacitors in equipment Time-constant (s); measured voltage (V)...: rotection in service access areas rotection in restricted access locations 2.2 SELV circuits General requirements See below Voltages under normal conditions (V)...: Equipment is supplied from SELV circuit and no generation of hazardous voltage is possible under normal operating conditions Voltages under fault conditions (V)...: No generation of hazardous voltage is possible under fault conditions Separation by double insulation or reinforced insulation (method 1) Separation by earthed screen (method 2) rotection by earthing of the SELV circuit (method 3) Connection of SELV circuits to other circuits...: See and SELV circuits are only connected to other SELV circuits.

16 age 14 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict 2.3 TNV circuits Limits The modem modules are approved component that generates only signals within the limits of SELV circuits. The telecommunication network is considered to be TNV-3 circuit. Type of TNV circuits...: See above Separation from other circuits and from accessible parts Insulation employed...: See above. Basic insulation between TNV-3 and SELV circuits provided Separation from hazardous voltages TNV-3 circuits separated to primary by reinforced or double insulation by the approved power adapter. TNV circuit only connected to SELV circuit. Insulation employed...: Connection of TNV circuits to other circuits TNV-3 circuits is separated to SELV circuits by basic insulation and separated to primary by reinforced or double insulation in the approved power adapter. Insulation employed...: See above Test for operating voltages generated externally 2.4 Limited current circuits General requirements Limit values Frequency (Hz)...: Measured current (ma)...: Measured voltage (V)...: Measured capacitance (µf)...: Connection of limited current circuits to other circuits 2.5 Limited power sources Inherently limited output Impedance limited output Overcurrent protective device limited output For USB ports: Complied with table 2B.

17 age 15 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict Regulating network limited output under normal operating and single fault condition Regulating network limited output under normal operating conditions and overcurrent protective device limited output under single fault condition Output voltage (V), output current (A), apparent power (VA)...: Current rating of overcurrent protective device (A) See appended table rovisions for earthing and bonding rotective earthing Class III equipment. The reliable earthing connection for coaxial cable of external TV tuner shall be evaluated in national mark approvaled Functional earthing rotective earthing and protective bonding conductors General Size of protective earthing conductors Rated current (A), cross-sectional area (mm 2 ), AWG...: Size of protective bonding conductors Rated current (A), cross-sectional area (mm 2 ), AWG...: Resistance (Ω) of earthing conductors and their terminations, test current (A)...: Colour of insulation...: Terminals General rotective earthing and bonding terminals Rated current (A), type and nominal thread diameter (mm)...: Separation of the protective earthing conductor from protective bonding conductors Integrity of protective earthing Interconnection of equipment Components in protective earthing conductors and protective bonding conductors

18 age 16 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict Disconnection of protective earth arts that can be removed by an operator arts removed during servicing Corrosion resistance Screws for protective bonding Reliance on telecommunication network or cable distribution system 2.7 Overcurrent and earth fault protection in primary circuits Basic requirements Instructions when protection relies on building installation Faults not covered in Short-circuit backup protection Number and location of protective devices...: rotection by several devices Warning to service personnel...: 2.8 Safety interlocks General principles rotection requirements Inadvertent reactivation Fail-safe operation Moving parts Overriding Switches and relays Contact gaps (mm)...: Overload test Endurance test Electric strength test Mechanical actuators 2.9 Electrical insulation

19 age 17 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict roperties of insulating materials Natural rubber, asbestos or hygroscopic material is not used Humidity conditioning Test for 48hrs. Humidity (%)...: 93 Temperature ( C)...: Grade of insulation The adequate levels of safety insulation is provided and maintained to comply with the requirements of this standard Clearances, creepage distances and distances through insulation General See , , Determination of working voltage Working voltage is considered to be within the TNV-3 parameters with U dc 120V, U ac 71Vpk. Therefore the following values have been used for tables 2K and 2L: U dc 140V used in table 2K, U dc 125V used in table 2L Clearances See below and advantage of annex G is not considered General See below Clearances in primary circuits Clearances in secondary circuits See appended table and Measurement of transient voltage levels Creepage distances See appended table and CTI tests...: CTI rating for all materials of min Solid insulation See appended table Minimum distance through insulation Thin sheet material rovided by approval modem. Number of layers (pcs)...: Electric strength test rinted boards

20 age 18 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict Distance through insulation Electric strength test for thin sheet insulating material Number of layers (pcs)...: Wound components Number of layers (pcs)...: Two wires in contact inside wound component; angle between 45 and 90...: Coated printed boards General Sample preparation and preliminary inspection Thermal cycling Thermal ageing ( C)...: Electric strength test Abrasion resistance test Electric strength test Enclosed and sealed parts...: Temperature T1=T2 + Tma Tamb +10K ( C)...: Spacings filled by insulating compound...: Electric strength test Component external terminations Insulation with varying dimensions 3 WIRING, CONNECTIONS AND SULY 3.1 General Current rating and overcurrent protection The cross-sectional area of the wires is adequate and complied with the relevant requirements rotection against mechanical damage The wireways are smooth and free from sharp edges Securing of internal wiring No excessive strain on wire and on terminal connections, loosing of terminal connections and damage of conductor insulation.

21 age 19 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict Insulation of conductors The insulation of the individual conductors is suitable for the application and the working voltage Beads and ceramic insulators Not used Screws for electrical contact pressure No such screws Insulating materials in electrical connections Self-tapping and spaced thread screws No self- tapping or spaced thread screws used Termination of conductors 10 N pull test Sleeving on wiring 3.2 Connection to an a.c. mains supply or a d.c. mains supply Means of connection...: Connection to an a.c. mains supply Connection to a d.c. mains supply Multiple supply connections ermanently connected equipment Number of conductors, diameter (mm) of cable and conduits...: Appliance inlets ower supply cords AC power supply cords Type...: Rated current (A), cross-sectional area (mm 2 ), AWG...: DC power supply cords Cord anchorages and strain relief Mass of equipment (kg), pull (N)...: Longitudinal displacement (mm)...: rotection against mechanical damage Cord guards D (mm); test mass (g)...: Radius of curvature of cord (mm)...: Supply wiring space

22 age 20 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict 3.3 Wiring terminals for connection of external conductors Wiring terminals Connection of non-detachable power supply cords Screw terminals Conductor sizes to be connected Rated current (A), cord/cable type, cross-sectional area (mm 2 )...: Wiring terminal sizes Rated current (A), type and nominal thread diameter (mm)...: Wiring terminals design Grouping of wiring terminals Stranded wire 3.4 Disconnection from the mains supply General requirement Disconnect devices ermanently connected equipment arts which remain energized Switches in flexible cords Single-phase equipment and d.c. equipment Three-phase equipment Switches as disconnect devices lugs as disconnect devices Interconnected equipment Multiple power sources 3.5 Interconnection of equipment General requirements See below Types of interconnection circuits...: SELV and TNV ELV circuits as interconnection circuits 4 HYSICAL REQUIREMENTS

23 age 21 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict 4.1 Stability Angle of 10 Test: force (N)...: Compliance. This appliance is of a stable mechanical construction and does not overbalance when tilted to an angle of 10 from its normal upright position with and without LCD screen open conditions. 4.2 Mechanical strength General After following tests, the equipment continues to comply with 2.1.1, 2.10 and Steady force test, 10 N Compliance Steady force test, 30 N Steady force test, 250 N Compliance Impact test Fall test Swing test Drop test Compliance Stress relief test Compliance at 70 C Cathode ray tubes icture tube separately certified...: High pressure lamps Wall or ceiling mounted equipment; force (N)...: 4.3 Design and construction Edges and corners All edges or corners accessible to operator are rounded and smoothed Handles and manual controls; force (N)...: Adjustable controls Securing of parts Electrical and mechanical connections can be expected to withstand usual mechanical stress.

24 age 22 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict Connection of plugs and sockets Mismatch of connectors were prevented by incompatible form or location Direct plug-in equipment Dimensions (mm) of mains plug for direct plug-in : Torque and pull test of mains plug for direct plug-in; torque (Nm); pull (N)...: Heating elements in earthed equipment Batteries For non-rechargable lithium type RTC battery: Reverse polarity installation is prevented by connector / socket design. The battery is protected from reverse charging by diode and resistor. For rechargable lithium type battery packs: Approved component and used within it s specified rating. No reverse polarity installation is possible due to socket design of battery pack Results see appended table and Oil and grease Dust, powders, liquids and gases Containers for liquids or gases Flammable liquids...: Quantity of liquid (l)...: Flash point ( C)...: Radiation; type of radiation...: See below General See below Ionizing radiation Measured radiation (pa/kg)...: Measured high-voltage (kv)...: Measured focus voltage (kv)...: CRT markings...:

25 age 23 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict Effect of ultraviolet (UV) radiation on materials art, property, retention after test, flammability classification...: Human exposure to ultraviolet (UV) radiation...: Laser (including LEDs) For O.D.D, which was approved component and evaluated according to relevant standard for laser product. Laser class...: Class 1. Diffusive type LEDs are used as indicating lights which are condisdered complied without tests Other types...: 4.4 rotection against hazardous moving parts General The hazardous moving part (DC fan) has been adequately guarded by the plastic enclosure. Other motors used in the appliance are certified H.D.D and no accessible to the user rotection in operator access areas See above rotection in restricted access locations rotection in service access areas 4.5 Thermal requirements Maximum temperatures See appended table Normal load condition per Annex L...: See Annex L Resistance to abnormal heat 4.6 Openings in enclosures Top and side openings Dimensions (mm)...: Bottoms of fire enclosures Construction of the bottom...: Doors or covers in fire enclosures

26 age 24 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict Openings in transportable equipment See appended table 4.6.1, Adhesives for constructional purposes Conditioning temperature ( C)/time (weeks)...: 4.7 Resistance to fire Reducing the risk of ignition and spread of flame See below. Method 1, selection and application of components wiring and materials Method 2, application of all of simulated fault condition tests Use of materials with the required flammability classes Conditions for a fire enclosure See below arts requiring a fire enclosure The fire enclosure is required for the following parts: Components in secondary circuits supplied by power sources that exceed the limits of limited power source Insulating wiring arts not requiring a fire enclosure Materials General Components and materials have adequate flammability classification. See appended table Materials for fire enclosures See appended table for enclosure material Materials for components and other parts outside fire enclosures Materials for components and other parts inside fire enclosures Materials for other parts outside fire enclosures is HB min. Internal components except small parts are V-2 or better Materials for air filter assemblies Materials used in high-voltage components 5 ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS 5.1 Touch current and protective conductor current General Equipment with approved SS power adapter used Equipment under test (EUT)

27 age 25 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict Test circuit Equipment is tested using the test circuit in figure 5A Application of measuring instrument Measuring instrument D1 is used Test procedure Considered Test measurements See Test voltage (V)...: Measured touch current (ma)...: Max. allowed touch current (ma)...: Measured protective conductor current (ma)...: Max. allowed protective conductor current (ma).: Equipment with touch current exceeding 3.5 ma : Touch currents to and from telecommunication networks and cable distribution systems and from telecommunication networks Limitation of the touch current to a telecommunication network and a cable distribution system See below. Considered, see below. Test voltage (V)...: See appended table Measured touch current (ma)...: See appended table Max. allowed touch current (ma)...: Summation of touch currents from telecommunication networks...: Only one telecommunication network port. 5.2 Electric strength General See below Test procedure For sub-clause test procedure. 5.3 Abnormal operating and fault conditions rotection against overload and abnormal operation See appended table Motors Motors used in the equipment are approved components (DC fan, H.D.D and O.D.D). See also appended table for detail Transformers

28 age 26 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict Functional insulation...: Functional insulation complied with the requirements c). Results see appended table Electromechanical components Simulation of faults Complied. Results see appended table Unattended equipment Compliance criteria for abnormal operating and fault conditions During and after tests: No fire occurred. No molten metal was emitted. No deformation of enclosure during the tests. No reduction of clearance and creepage distances Electric strength tests are performed on basic insulation and were passed. 6 CONNECTION TO TELECOMMUNICATION NETWORKS 6.1 rotection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment rotection from hazardous voltages Separation of the telecommunication network from earth Requirements Basic insulation provided between TNV-3 circuit and SELV circuit. Test voltage (V)...: See appended table 5.2. Current in the test circuit (ma)...: Exclusions...: 6.2 rotection of equipment users from overvoltages on telecommunication networks Separation requirements Adequate electrical separation between TNV-3 to: - Keyboard or external enclosure - SELV circuits - User accessible connector Electric strength test procedure See below.

29 age 27 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict Impulse test See appended table Steady-state test See appended table Compliance criteria No isolation breakdown. 6.3 rotection of the telecommunication wiring system from overheating Max. output current (A)...: Current limiting method...: 7 CONNECTION TO CABLE DISTRIBUTION SYSTEMS 7.1 rotection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment 7.2 rotection of equipment users from overvoltages on the cable distribution system 7.3 Insulation between primary circuits and cable distribution systems Circuits in the equipment intended to be directly connect to a cable distribution system, which consider to comply with requirements of TNV-1 circuit. IEC , 2nd Edition, subclause 7.3 was used for evaluated. See General product information - Engineering Consideration for details. See below General Compliance is checked by the voltage surge test of and impulse test of Voltage surge test 10 kv of surge test voltage is applied between the AC mains and the antenna connection points of TV tuner (without earthed connection). After the test, the insulation in compliance with the electric strength test requirement of Impulse test 4 kv of impulse test voltage applied between the AC mains and the antenna connection points of TV tuner (without earthed connection). After the test, the insulation in compliance with the electric strength test requirement of

30 age 28 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict A ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE A.1 Flammability test for fire enclosures of movable equipment having a total mass exceeding 18 kg, and of stationary equipment (see ) A.1.1 Samples...: Wall thickness (mm)...: A.1.2 Conditioning of samples; temperature ( C)...: A.1.3 Mounting of samples...: A.1.4 Test flame (see IEC ) Flame A, B, C or D...: A.1.5 Test procedure A.1.6 Compliance criteria Sample 1 burning time (s)...: Sample 2 burning time (s)...: Sample 3 burning time (s)...: A.2 Flammability test for fire enclosures of movable equipment having a total mass not exceeding 18 kg, and for material and components located inside fire enclosures (see and ) A.2.1 Samples, material...: Wall thickness (mm)...: A.2.2 Conditioning of samples A.2.3 Mounting of samples...: A.2.4 Test flame (see IEC ) Flame A, B or C...: A.2.5 Test procedure A.2.6 Compliance criteria Sample 1 burning time (s)...: Sample 2 burning time (s)...: Sample 3 burning time (s)...: A.2.7 Alternative test acc. to IEC , cl. 4 and 8 Sample 1 burning time (s)...: Sample 2 burning time (s)...: Sample 3 burning time (s)...: A.3 Hot flaming oil test (see 4.6.2) A.3.1 Mounting of samples

31 age 29 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict A.3.2 Test procedure A.3.3 Compliance criterion B ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see and 5.3.2) B.1 General requirements Certified DC fan and H.D.D. used. osition...: Manufacturer...: Type...: Rated values...: B.2 Test conditions B.3 Maximum temperatures B.4 Running overload test B.5 Locked-rotor overload test Test duration (days)...: Electric strength test: test voltage (V)...: B.6 Running overload test for d.c. motors in secondary circuits B.7 Locked-rotor overload test for d.c. motors in secondary circuits B.7.1 Test procedure B.7.2 Alternative test procedure; test time (h)...: B.7.3 Electric strength test B.8 Test for motors with capacitors B.9 Test for three-phase motors B.10 Test for series motors Operating voltage (V)...: C ANNEX C, TRANSFORMERS (see and 5.3.3) osition...: Manufacturer...: Type...: Rated values...: Method of protection...: C.1 Overload test

32 age 30 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict C.2 Insulation rotection from displacement of windings...: D ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS (see 5.1.4) D.1 Measuring instrument Complied. D.2 Alternative measuring instrument E ANNEX E, TEMERATURE RISE OF A WINDING (see ) F ANNEX F, MEASUREMENT OF CLEARANCES AND CREEAGE DISTANCES (see 2.10) G ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM CLEARANCES G.1 Summary of the procedure for determining minimum clearances G.2 Determination of mains transient voltage (V)...: G.2.1 AC mains supply G.2.2 DC mains supply G.3 Determination of telecommunication network transient voltage (V)...: G.4 Determination of required withstand voltage (V)...: G.5 Measurement of transient levels (V)...: G.6 Determination of minimum clearances...: H ANNEX H, IONIZING RADIATION (see ) J ANNEX J, TABLE OF ELECTROCHEMICAL OTENTIALS (see ) Metal used...: K ANNEX K, THERMAL CONTROLS (see and 5.3.7) K.1 Making and breaking capacity K.2 Thermostat reliability; operating voltage (V)...: K.3 Thermostat endurance test; operating voltage (V)...:

33 age 31 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict K.4 Temperature limiter endurance; operating voltage (V)...: K.5 Thermal cut-out reliability K.6 Stability of operation L ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYES OF ELECTRICAL BUSINESS EQUIMENT (see and 4.5.1) L.1 Typewriters L.2 Adding machines and cash registers L.3 Erasers L.4 encil sharpeners L.5 Duplicators and copy machines L.6 Motor-operated files L.7 Other business equipment See summary of testing. M ANNEX M, CRITERIA FOR TELEHONE RINGING SIGNALS (see 2.3.1) M.1 Introduction M.2 Method A M.3 Method B M.3.1 Ringing signal M Frequency (Hz)...: M Voltage (V)...: M Cadence; time (s), voltage (V)...: M Single fault current (ma)...: M.3.2 Tripping device and monitoring voltage...: M Conditions for use of a tripping device or a monitoring voltage M Tripping device M Monitoring voltage (V)...: N ANNEX N, IMULSE TEST GENERATORS (see , , and clause G.5) N.1 ITU-T impulse test generators Circuit reference 1 used. N.2 IEC impulse test generator Circuit reference 3 used.

34 age 32 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict ANNEX, NORMATIVE REFERENCES Q ANNEX Q, BIBLIOGRAHY R ANNEX R, EXAMLES OF REQUIREMENTS FOR QUALITY CONTROL ROGRAMMES R.1 Minimum separation distances for unpopulated coated printed boards (see ) R.2 Reduced clearances (see ) S ANNEX S, ROCEDURE FOR IMULSE TESTING (see ) S.1 Test equipment S.2 Test procedure S.3 Examples of waveforms during impulse testing T ANNEX T, GUIDANCE ON ROTECTION AGAINST INGRESS OF WATER (see 1.1.2) U ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED INSULATION (see ) V ANNEX V, AC OWER DISTRIBUTION SYSTEMS (see 1.6.1) V.1 Introduction V.2 TN power distribution systems V.3 TT power systems V.4 IT power systems W ANNEX W, SUMMATION OF TOUCH CURRENTS W.1 Touch current from electronic circuits W.1.2 Earthed circuits W.2 Interconnection of several equipments W.2.1 Isolation W.2.2 Common return, isolated from earth

35 age 33 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict W.2.3 Common return, connected to protective earth X ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS (see clause C.1) X.1 Determination of maximum input current X.2 Overload test procedure Y ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see ) Y.1 Test apparatus...: Y.2 Mounting of test samples...: Y.3 Carbon-arc light-exposure apparatus...: Y.4 Xenon-arc light exposure apparatus...:

36 age 34 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict CENELEC COMMON MODIFICATIONS [C], SECIAL NATIONAL CONDITIONS [S] AND A-DEVIATIONS (NATIONAL DEVIATIONS) [A] (EN :2001, Annex ZB and Annex ZC) General C: Delete all the "country" notes in the reference document according to the following list: Note Note Note Note Note Note Note Note Note 2, 7, Note 1, Note 2, Note Note Note Note 1, Note Note 1, Note Note Note Note Note Note Note 7 Note Note G2.1 Note 1, 2 Annex H Note S (DK): Certain types of Class I appliances (see ) may be provided with a plug not establishing earthing conditions when inserted into Danish socket-outlets A (SE, Ordinance 1990:944 and CH, Ordinance on environmentally hazardous substances SR , Annex 3.2, Mercury): Add NOTE Switches containing mercury such as thermostats, relays and level controllers are not allowed S (NO): Due to the IT power system used (see annex V, Fig. V.7), capacitors are required to be rated for the applicable line-to-line voltage (230 V) S (FI, NO, SE): CLASS I LUGGABLE EQUIMENT TYE A intended for connection to other equipment or a network shall, if safety relies on connection to protective earth or if surge suppressors are connected between the network terminals and accessible parts, have a marking stating that the equipment must be connected to an earthed mains socket-outlet. The marking text in the applicable countries shall be as follows: FI: "Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan" Deleted. No direct connection to the mains supply. Not applied for. Not applied for. Not applied for. Not applied for. NO: "Apparatet må tilkoples jordet stikkontakt" Not applied for. SE: "Apparaten skall anslutas till jordat uttag" Not applied for. A (DK, Heavy Current Regulations): Supply cords of class I equipment, which is delivered without a plug, must be provided with a visible tag with the following text: Vigtigt! Lederen med grøn/gul isolation må kun tilsluttes en klemme mærket eller Class III equipment.

37 age 35 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict If essential for the safety of the equipment, the tag must in addition be provided with a diagram which shows the connection of the other conductors, or be provided with the following text: "For tilslutning af de øvrige ledere, se medfølgende instalationsvejledning." S (DK): Socket-outlets for providing power to other equipment shall be in accordance with the Heavy Current Regulations, Section D1, Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a, when used on Class I equipment. For stationary equipment the socket-outlet shall be in accordance with Standard Sheet DK 1-1b or DK 1-5a A (DK, Heavy Current Regulations): CLASS II EQUIMENT shall not be fitted with socketoutlets for providing power to other equipment A (DE, Gesetz über technische Arbeitsmittel (Gerätesicherheitsgesetz) [Law on technical labour equipment {Equipment safety law}], of 23 rd October 1992, Article 3, 3 rd paragraph, 2 nd sentence, together with the "Allgemeine Verwaltungsvorschrift zur Durchführung des Zweiten Abschnitts des Gerätesicherheitsgesetzes" [General administrative regulation on the execution of the Second Section of the Equipment safety law], of 10 th January 1996, article 2, 4 th paragraph item 2): Directions for use with rules to prevent certain hazards for (among others) maintenance of the technical labour equipment, also for imported technical labour equipment shall be written in the German language. NOTE: Of this requirement, rules for use even only by service personnel are not exempted A (CH, Ordinance on environmentally hazardous substances SR ): Annex 4.10 of SR applies for batteries. A (DE, Regulation on protection against hazards by X-ray, of 8 th January 1987, Article 5 [Operation of X-ray emission source], clauses 1 to 4): a) A licence is required by those who operate an X-ray emission source. b) A licence in accordance with Cl. 1 is not required by those who operate an X-ray emission source on which the electron acceleration voltage does not exceed 20 kv if 1) the local dose rate at a distance of 0,1 m from the surface does not exceed 1 µsv/h and No socket-outlets. Class III equipment. Equipment is not technical labour equipment. User s manual and marking label are in English. Battery pack and RTC battery are in compliance with requirements of IEC Overall compliance needs to be evaluated during the national approval process. This national difference was deleted by A11 of EN

38 age 36 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict 2) it is adequately indicated on the X-ray emission source that i) X-rays are generated and ii) the electron acceleration voltage must not exceed the maximum value stipulated by the manufacturer or importer. c) A licence in accordance with Cl. 1 is also not required by persons who operate an X-ray emission source on which the electron acceleration voltage exceeds 20 kv if 1) the X-ray emission source has been granted a type approval and 2) it is adequately indicated on the X-ray emission source that i) X-rays are generated ii) the device stipulated by the manufacturer or importer guarantees that the maximum permissible local dose rate in accordance with the type approval is not exceeded and iii) the electron acceleration voltage must not exceed the maximum value stipulated by the manufacturer or importer. d) Furthermore, a licence in accordance with Cl. 1 is also not required by persons who operate X-ray emission sources on which the electron acceleration voltage does not exceed 30 kv if 1) the X-rays are generated only by intrinsically safe CRTs complying with Enclosure III, No. 6, 2) the values stipulated in accordance with Enclosure III, No. 6.2 are limited by technical measures and specified in the device and 3) it is adequately indicated on the X-ray emission source that the X-rays generated are adequately screened by the intrinsically safe CRT S (NO): Requirements according to this annex, and apply S (NO): Requirements according to this annex, apply and S (NO): Requirements according to this annex, and apply S (GB): The current rating of the circuit shall be taken as 13 A, not 16 A C: Replace the subclause as follows: Basic requirements To protect against excessive current, shortcircuits and earth faults in RIMARY CIRCUITS, protective devices shall be included either as integral parts of the equipment or as parts of the building installation, subject to the following, a), b) Not applied for. Not applied for. Not applied for. Class III equipment. Replaced.

39 age 37 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict and c): a) except as detailed in b) and c), protective devices necessary to comply with the requirements of 5.3 shall be included as parts of the equipment; b) for components in series with the mains input to the equipment such as the supply cord, appliance coupler, r.f.i. filter and switch, shortcircuit and earth fault protection may be provided by protective devices in the building installation; c) it is permitted for LUGGABLE EQUIMENT TYE B or ERMANENTLY CONNECTED EQUIMENT, to rely on dedicated overcurrent and short-circuit protection in the building installation, provided that the means of protection, e.g. fuses or circuit breakers, is fully specified in the installation instructions. If reliance is placed on protection in the building installation, the installation instructions shall so state, except that for LUGGABLE EQUIMENT TYE A the building installation shall be regarded as providing protection in accordance with the rating of the wall socket outlet. S (GB): To protect against excessive currents and short-circuits in the RIMARY CIRCUIT OF DIRECT LUG-IN EQUIMENT, protective device shall be included as integral parts of the DIRECT LUG- IN EQUIMENT. Not direct plug-in equipment C: Void. Declared C: Replace in the first line "(see also 1.4.7)" by "(see also 1.4.8)" S (NO): Due to the IT power distribution system used (see annex V, Fig. V.7), the A.C. MAINS SULY voltage is considered to be equal to the line-to-line voltage and will remain at 230 V in case of a single earth fault Replaced. Not applied for.

40 age 38 of 73 Report No.: IEC / EN Clause Requirement Test Result Remark Verdict S (CH): Supply cords of equipment having a RATED CURRENT not exceeding 10 A shall be provided with a plug complying with SEV 1011 or IEC and one of the following dimension sheets: SEV , lug type 15, 3+N+E 250/400 V, 10 A SEV , lug type 11, L+N 250 V, 10 A SEV , lug type 12, L+N+E 250 V, 10 A In general, EN applies for plugs for currents exceeding 10 A. However, a 16 A plug and socket-outlet system is being introduced in Switzerland, the plugs of which are according to the following dimension sheets, published in February 1998: SEV , lug type 25, 3L+N+E 230/400 V, 16 A SEV , lug type 21, L+N 250 V, 16 A SEV , lug type 23, L+N+E 250 V, 16 A S (DK): Supply cords of single-phase equipment having a rated current not exceeding 13 A shall be provided with a plug according to the Heavy Current Regulations, Section D1. CLASS I EQUIMENT provided with socket-outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with standard sheet DK 2-1a or DK 2-5a. If ply-phase equipment and single-phase equipment having a RATED CURRENT exceeding 13 A is provided with a supply cord with a plug, this plug shall be in accordance with the Heavy Current Regulations, Section D1 or EN S (ES): Supply cords of single-phase equipment having a rated current not exceeding 10 A shall be provided with a plug according to UNE 20315:1994. Supply cords of single-phase equipment having a rated current not exceeding 2,5 A shall be provided with a plug according to UNE-EN 50075:1993. CLASS I EQUIMENT provided with socket-outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules, shall be provided with a plug in accordance with standard UNE 20315:1994. If poly-phase equipment is provided with a supply cord with a plug, this plug shall be in accordance with UNE-EN No power supply cord provided. No power supply cord provided. No power supply cord provided. S (GB): Apparatus which is fitted with a flexible No power supply cord provided.