Test Report issued under the responsibility of:

Transcription

1 age 1 of 30 Test Report issued under the responsibility of: Intertek Testing Services Shenzhen Ltd. Guangzhou Branch TEST REORT Luminaires art 2: articular requirements: Section Six Luminaires with built-in transformers or convertors for filament lamps Report Reference No...: GZ Date of issue...: 13 Aug Total number of pages CB Testing Laboratory...: Address...: Applicant s name...: Address...: Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Block E, No.7-2 Guang Dong Software Science ark, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China Eaglerise Electronics (Foshan) Co., Ltd. No. 4, East Huanzhen Road, Beijiao, Shunde, Foshan, Guangdong, , China Test specification: Standard...: Test procedure...: Non-standard test method..: Test Report Form No...: Test Report Form(s) Originator...: :1994+A1:1996 used in conjunction with IEC :2008 EN :1994+A1:1997 used in conjunction with EN :2008+A11: 2009 Additional requirements of independent Electronic controlgear for LED IEC60598_2_6A Intertek Semko AB Master TRF...: Copyright 2008 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. If this Test Report Form is used by non-iecee members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.

2 age 2 of 30 Test item description... : Trade Mark...: Electronic controlgear for LED (Electronic LED driver) Manufacturer...: Model/Type reference...: Ratings...: Same as applicant EI016C****LS Remark: The 1 st to 4 th * indicate the output current of LED driver; can be replaced by 0350 to 1400 and increasing in multiplies of means 350 ma; 1400 means 1400 ma. Input: VAC; 50/60 Hz; 0,15 A; Class II; I 20; SELV; ta 50 C; tc 80 C; Independent type; 110 C thermal protection; Inherently short-circuit proof; Output: Constant current type for output; MM mark; Suitable for direct mounting on normally flammable surfaces; Other parameters refer to appendix for model list in test report.

3

4 age 4 of 30 Summary of testing: The tested samples fulfilled the requirements of specified standards. All models had the same mechanical structure, output load, CB layout; the only deference is the parameters for the components used in secondary circuit. Model EI016C1400LS was selected to do the full tests as its maximum secondary output current. Tests performed (name of test and test clause): 6.5 Marking 6.6 Construction 6.7 Creepage distances and clearance 6.9 Terminals 6.10 External and internal wiring 6.11 rotection against electric shock 6.12 Endurance tests and thermal tests 6.13 Resistance to dust and moisture 6.14 Insulation resistance and electric strength 6.15 Resistance to heat, fire and tracking Testing location: Block E, No.7-2 Guang Dong Software Science ark, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China Summary of compliance with National Differences: Not checked. Copy of marking plate lease refer to report: GZ

5 age 5 of 30 Test item particulars...: Classification of installation and use...: Supply Connection...: Independent; Class II; for use with LED Terminal blocks ossible test case verdicts: - test case does not apply to the test object...: - test object does meet the requirement...: (ass) - test object does not meet the requirement...: F (Fail) Testing...: Date of receipt of test item...: 21 Jul Date (s) of performance of tests...: 21 Jul to 13 Aug General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Throughout this report a comma is used as the decimal separator. Clause numbers between brackets refer to clauses in IEC When determining for test conclusion, measurement uncertainty of tests has been considered. This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. The test report only allows to be revised only within the report defined retention period unless standard or regulation was withdrawn or invalid. The clause which indicated with * is the subcontract test item. This report shall be used with GZ This report is totally 30 pages; age 1-28 is test report, page 29 is model list, and page 30 is product photos. Manufacturer site: Eaglerise Electronics (Foshan) Co., Ltd. Address: No. 4, East Huanzhen Road, Beijiao, Shunde, Foshan, Guangdong, , China. General product information: The products covered by this report are Class II; independent; SELV; LED drivers.

6 age 6 of (0) GENERAL TEST REQUIREMENTS 6.2 (0.1) Information for luminaire design considered Standard EN Yes No 64.2 (0.3) More sections applicable...: Yes No 6.4 (2) CLASSIFICATION 6.4 (2.2) Type of protection (Class 0 excluded)... : Class II 6.4 (2.3) Degree of protection (Requirement: Ordinary)... : I (2.4) Luminaire suitable for direct mounting on normally flammable surfaces... : Luminaire not suitable for direct mounting on normally flammable surfaces... : Yes No Yes No 6.4 (2.5) Luminaire for normal use... : Yes No Luminaire for rough service... : Yes No 6.5 (3) MARKING 6.5 (3.2) Mandatory markings osition of the marking Format of symbols/text 6.5 (3.3) Additional information Language of instructions 6.5 (3.3.1) Combination luminaires 6.5 (3.3.2) Nominal frequency in Hz 50/ (3.3.3) Operating temperature 6.5 (3.3.4) Symbol or warning notice 6.5 (3.3.5) Wiring diagram 6.5 (3.3.6) Special conditions 6.5 (3.3.7) Metal halide lamp luminaire warning 6.5 (3.3.8) Limitation for semi-luminaires 6.5 (3.3.9) ower factor and supply current 6.5 (3.3.10) Suitability for use indoors 6.5 (3.3.11) Luminaires with remote control 6.5 (3.3.12) Clip-mounted luminaire warning 6.5 (3.3.13) Specifications of protective shields

7 age 7 of (3.3.14) Symbol for nature of supply 6.5 (3.3.15) Rated current of socket outlet 6.5 (3.3.16) Rough service luminaire 6.5 (3.3.17) Mounting instruction for type Y, type Z and some type X attachments 6.5 (3.3.18) Non-ordinary luminaires with VC cable 6.5 (3.3.19) rotective conductor current in instruction if applicable 6.5 (3.3.20) rovided with information if not intended to be mounted within arms reach 6.5 (3.4) Test with water Test with hexane Legible after test Label attached (-) Rated voltage (-) Output voltage visible during lamp replacement (-) Warning notice (-) Marking on transformer or convertor (-) Fuse-link rating 6.6 (4) CONSTRUCTION 6.6 (4.2) Components replaceable without difficulty Input and output wire 6.6 (4.3) Wireways smooth and free from sharp edges 6.6 (4.4) Lampholders 6.6 (4.4.1) Integral lampholder 6.6 (4.4.2) Wiring connection 6.6 (4.4.3) Lampholder for end-to-end mounting 6.6 (4.4.4) ositioning - pressure test (N)...: After test the lampholder comply with relevant standard sheets and show no damage After test on single-capped lampholder the lampholder have not moved from its position and show no permanent deformation - bending test (N)...: After test the lampholder have not moved from its position and show no permanent deformation

8 age 8 of (4.4.5) eak pulse voltage 6.6 (4.4.6) Centre contact (4.4.7) arts in rough service luminaires resistant to tracking 6.6 (4.4.8) Lamp connectors 6.6 (4.4.9) Caps and bases correctly used 6.6 (4.5) Starter holders Starter holder in luminaires other than class II Starter holder class II construction 6.6 (4.6) Terminal blocks Tails Unsecured blocks 6.6 (4.7) Terminals and supply connections 6.6 (4.7.1) Contact to metal parts 6.6 (4.7.2) Test 8 mm live conductor Test 8 mm earth conductor 6.6 (4.7.3) Terminals for supply conductors 6.6 ( ) Welded connections: - stranded or solid conductor - spot welding - welding between wires - Type Z attachment - mechanical test according to electrical test according to heat test according to and (4.7.4) Terminals other than supply connection 6.6 (4.7.5) Heat-resistant wiring/sleeves 6.6 (4.7.6) Multi-pole plug - test at 30 N 6.6 (4.8) Switches: - adequate rating - adequate fixing - polarized supply - compliance with for electronic switches

9 age 9 of (4.9) Insulating lining and sleeves 6.6 (4.9.1) Retainement Method of fixing...: Insulation tape; fixed by structure 6.6 (4.9.2) Insulated linings and sleeves Resistant to a temperature > 20 C to the wire temperature or a) & c) Insulation resistance and electric strength b) Ageing test. Temperature ( C)...: 6.6 (4.10) Insulation of Class II luminaires 6.6 (4.10.1) No contact, mounting surface accessible metal parts wiring of basic insulation Safe installation fixed luminaires Capacitors and switches Interference suppression capacitors according to IEC (4.10.2) Assembly gaps: - not coincidental - no straight access with test probe 6.6 (4.10.3) Retainment of insulation: - fixed - unable to be replaced; luminaire inoperative - sleeves retained in position - lining in lampholder 6.6 (4.11) Electrical connections 6.6 (4.11.1) Contact pressure 6.6 (4.11.2) Screws: - self-tapping screws - thread-cutting screws 6.6 (4.11.3) Screw locking: - spring washer - rivets 6.6 (4.11.4) Material of current-carrying parts 6.6 (4.11.5) No contact to wood or mounting surface 6.6 (4.11.6) Electro-mechanical contact systems

10 age 10 of (4.12) Mechanical connections and glands 6.6 (4.12.1) Screws not made of soft metal Screws of insulating material Torque test: torque (Nm); part...: Fixed enclosure screw: 0,5 Nm; Torque test: torque (Nm); part...: Torque test: torque (Nm); part...: 6.6 (4.12.2) Screws with diameter < 3 mm screwed into metal 6.6 (4.12.4) Locked connections: - fixed arms; torque (Nm)...: - lampholder; torque (Nm)...: - push-button switches; torque 0,8 Nm...: 6.6 (4.12.5) Screwed glands; force (Nm)...: 6.6 (4.13) Mechanical strength 6.6 (4.13.1) Impact tests: - fragile parts; energy (Nm)...: - other parts; energy (Nm)...: Enclosure: 0,5 Nm 1) live parts 2) linings 3) protection 4) covers 6.6 (4.13.3) Straight test finger 6.6 (4.13.4) Rough service luminaires - I54 or higher a) fixed b) hand-held c) delivered with a stand d) for temporary installations and suitable for mounting on a stand 6.6 (4.13.6) Tumbling barrel 6.6 (4.14) Suspensions and adjusting devices 6.6 (4.14.1) Mechanical load: A) four times the weight B) torque 2,5 Nm C) bracket arm; bending moment (Nm)...:

11 age 11 of 30 D) load track-mounted luminaires E) clip-mounted luminaires, glass-shelve. Thickness (mm)...: Metal rod. diameter (mm)...: Fixed luminaire or independent control gear without fixing devices 6.6 (4.14.2) Load to flexible cables Mass (kg)...: Stress in conductors (N/mm²)...: Mass (kg) of semi-luminaire...: Bending moment (Nm) of semi-luminaire...: 6.6 (4.14.3) Adjusting devices: - flexing test; number of cycles...: - strands broken - electric strength test afterwards 6.6 (4.14.4) Telescopic tubes: cords not fixed to tube; no strain on conductors 6.6 (4.14.5) Guide pulleys 6.6 (4.14.6) Strain on socket-outlets 6.6 (4.15) Flammable materials: - glow-wire test 650 C Enclosure - spacing 30 mm - screen withstanding test of screen dimensions - no fiercely burning material - thermal protection - electronic circuits exempted 6.6 (4.15.2) Luminaires made of thermoplastic material with lamp control gear a) construction b) temperature sensing control c) surface temperature 6.6 (4.16) Luminaires for mounting on normally flammable surfaces No lamp control gear (compliance with Section 12) 6.6 (4.16.1) Lamp control gear spacing: - spacing 35 mm

12 age 12 of 30 - spacing 10 mm 6.6 (4.16.2) Thermal protection: - in lamp control gear - external - fixed position - temperature marked lamp control gear 6.6 (4.16.3) Design to satisfy the test of 12.6 (see 12.6) 6.6 (4.17) Drain holes Clearance at least 5 mm 6.6 (4.18) Resistance to corrosion: 6.6 (4.18.1) - rust-resistance 6.6 (4.18.2) - season cracking in copper 6.6 (4.18.3) - corrosion of aluminium 6.6 (4.19) Ignitors compatible with ballast 6.6 (4.20) Rough service vibration 6.6 (4.21) rotective shield: 6.6 (4.21.1) Shield fitted Shield of glass if tungsten halogen lamps 6.6 (4.21.2) articles from a shattering lamp not impair safety 6.6 (4.21.3) No direct path 6.6 (4.21.4) Impact test on shield Glow-wire test on lamp compartment 6.6 (4.22) Attachments to lamps 6.6 (4.23) Semi-luminaires comply Class II 6.6 (4.24) UV radiation for tungsten halogen lamps and metal halide lamps (Annex ) 6.6 (4.25) No sharp point or edges 6.6 (4.26) Short-circuit protection: 6.6 (4.26.1) Uninsulated accessible SELV parts 6.6 (4.26.2) Short-circuit test 6.6 (4.26.3) Test chain according to Figure (-) Electrical safety output circuit

13 age 13 of (11) CREEAGE DISTANCES AND CLEARANCES Working voltage (V)...: Voltage form Sinusoidal Non-sinusoidal TI < 600 > 600 Impulse withstand category (Normal category II) (Category III Annex U) Category II Category III Rated pulse voltage (kv)...: Measured circuit...: rimary (1) Current-carrying parts of different polarity: cr (mm); cl (mm)...: (2) Current-carrying parts and accessible parts: cr (mm); cl (mm)...: Approval terminal block Currentcarrying parts of different polarity in CB: Cr. 5,8 mm (limit: 2,5 mm); Cl. 5,8 mm (limit: 1,5 mm) Live parts in CB and accessible parts: Cr. >=7,1 mm (limit: 5,0 mm); Cl. >=7,1 mm (limit: 3,0 mm) Secondary (Max. 52 VDC) Approval terminal block Live parts in CB and accessible parts: Cr. >=7,1 mm (limit: 3,2,mm); Cl. >=7,1 mm (limit: 1,6 mm) (3) arts becoming live due to breakdown of basic insulation and metal parts: cr (mm); cl (mm)...:

14 age 14 of 30 (4) Outer surface of cable where it is clamped and metal parts: cr (mm); cl (mm)...: Input wire clamped by cord anchorage to metal screw: Cr. >= 4,0 mm (limit: 2,5 mm); Cl. >= 4,0 mm (limit: 1,5 mm) (5) Not used (6) Current-carrying parts and supporting surface: cr (mm); cl (mm)...: Between transformer windings: cr (mm); cl (mm).: Live parts in CB and supporting surface: Cr. >=7,1 mm (limit: 5,0 mm); Cl. >=7,1 mm (limit: 3,0 mm); Output wire clamped by cord anchorage to metal screw: Cr. >= 4,0 mm (limit: 1,6 mm); Cl. >= 4,0 mm (limit: 0,8 mm) Live parts in CB and supporting surface: Cr. >=7,1 mm (limit: 3,2 mm); Cl. >=7,1 mm (limit: 1,6 mm); 6.8 (7) ROVISION FOR EARTHING 6.8 ( ) 6.8 ( ) Accessible metal parts Metal parts in contact with supporting surface Resistance < 0,5 Ω Self-tapping screws used Thread-forming screws Thread-forming screw used in a grove Earth makes contact first Earth continuity in joints etc. 6.8 (7.2.4) Locking of clamping means Compliance with Terminal blocks with integrated screwless earthing contacts tested according Annex V 6.8 (7.2.5) Earth terminal integral part of connector socket 6.8 (7.2.6) Earth terminal adjacent to mains terminals

15 age 15 of (7.2.7) Electrolytic corrosion of the earth terminal 6.8 (7.2.8) Material of earth terminal Contact surface bare metal 6.8 (7.2.10) Class II luminaire for looping-in Double or reinforced insulation to functional earth 6.8 (7.2.11) Earthing core coloured green-yellow Length of earth conductor (-) Metal shell of lampholders (-) Earthing of secondary circuit (-) Current path during operation 6.9 (14) SCREW TERMINALS Separately approved; component list Approval terminal block (see Annex 1) art of the luminaire (see Annex 3) 6.9 (15) SCREWLESS TERMINALS AND ELECTRICAL CONNECTIONS Separately approved; component list (see Annex 1) art of the luminaire (see Annex 4) 6.10 (5) EXTERNAL AND INTERNAL WIRING 6.10 (5.2) Supply connection and external wiring 6.10 (5.2.1) Means of connection...: Terminal blocks 6.10 (5.2.2) Type of cable...: Nominal cross-sectional area (mm²)...: Cables equal to IEC or IEC (5.2.3) Type of attachment, X, Y or Z 6.10 (5.2.5) Type Z not connected to screws 6.10 (5.2.6) Cable entries: - suitable for introduction - adequate degree of protection 6.10 (5.2.7) Cable entries through rigid material have rounded edges 6.10 (5.2.8) Insulating bushings: - suitably fixed

16 age 16 of 30 - material in bushings - material not likely to deteriorate - tubes or guards made of insulating material 6.10 (5.2.9) Locking of screwed bushings 6.10 (5.2.10) Cord anchorage: - covering protected from abrasion - clear how to be effective - no mechanical or thermal stress - no tying of cables into knots etc. - insulating material or lining 6.10 ( ) Cord anchorage for type X attachment: a) at least one part fixed b) types of cable c) no damaging of the cable d) whole cable can be mounted e) no touching of clamping screws f) metal screw not directly on cable g) replacement without special tool 6.10 ( ) 6.10 ( ) Glands not used as anchorage Labyrinth type anchorages Adequate cord anchorage for type Y and type Z attachment Tests: - impossible to push cable; unsafe - pull test: 25 times; pull (N)...: Input: H03VVH2-F; 2 X 0,5~0,75 mm 2 ; 60 N; Output: H03VVH2-F; 2 X 0,5~1,5 mm 2 ; 60 N - torque test: torque (Nm)...: Input: H03VVH2-F; 2 X 0,5~0,75 mm 2 ; 0,15 Nm; Output: H03VVH2-F; 2 X 0,5~1,5 mm 2 ; 0,25 Nm - displacement 2 mm - no movement of conductors - no damage of cable or cord

17 age 17 of (5.2.11) External wiring passing into luminaire 6.10 (5.2.12) Looping-in terminals 6.10 (5.2.13) Wire ends not tinned Wire ends tinned: no cold flow 6.10 (5.2.14) Mains plug same protection Class III luminaire plug 6.10 (5.2.16) Appliance inlets (IEC 60320) Appliance couplers of class II type 6.10 (5.2.17) No standardized interconnecting cables properly assembled 6.10 (5.2.18) Used plug in accordance with - IEC other standard 6.10 (5.3) Internal wiring 6.10 (5.3.1) Internal wiring of suitable size and type Through wiring - not delivered/ mounting instruction - factory assembled - socket outlet loaded (A)...: - temperatures...: (see Annex 2) Green-yellow for earth only 6.10 ( ) Internal wiring connected directly to fixed wiring Cross-sectional area (mm²)...: Insulation thickness Extra insulation added where necessary 6.10 ( ) Internal wiring connected to fixed wiring via internal current-limiting device Adequate cross-sectional area and insulation thickness 6.10 ( ) Double or reinforced insulation for class II 6.10 ( ) Conductors without insulation 6.10 ( ) SELV current-carrying parts 6.10 ( ) Insulation thickness other than VC or rubber 6.10 (5.3.2) Sharp edges etc. No moving parts of switches etc. Joints, raising/lowering devices

18 age 18 of 30 Telescopic tubes etc. No twisting over (5.3.3) Insulating bushings: - suitable fixed - material in bushings - material not likely to deteriorate - cables with protective sheath 6.10 (5.3.4) Joints and junctions effectively insulated 6.10 (5.3.5) Strain on internal wiring 6.10 (5.3.6) Wire carriers 6.10 (5.3.7) Wire ends not tinned Wire ends tinned: no cold flow 6.11 (8) ROTECTION AGAINST ELECTRIC SHOCK 6.11 (8.2.1) Live parts not accessible Basic insulated parts not used on the outer surface without appropriate protection Basic insulated parts not accessible with standard test finger on portable and adjustable luminaires Basic insulated parts not accessible with Ø 50 mm probe from outside, within arms reach, on wall-mounted luminaires Lampholder and starterholders in portable and adjustable luminaires comply with double or reinforced insulation requirements Basic insulation only accessible under lamp or starter replacement rotection in any position Double-ended tungsten filament lamp Insulation lacquer not reliable Double-ended high pressure discharge lamp Relevant warning according to fitted to the luminaire 6.11 (8.2.2) ortable luminaire adjusted in most unfavourable position 6.11 (8.2.3.a) Class II luminaire: - basic insulated metal parts not accessible during starter or lamp replacement

19 age 19 of 30 - basic insulation not accessible other than during starter or lamp replacement - glass protective shields not used as supplementary insulation 6.11 (8.2.3.b) BC lampholder of metal in class I luminaires shall be earthed 6.11 (8.2.3.c) Class III luminaires with exposed SELV parts: Ordinary luminaire: - touch current...: - no-load voltage...: Other than ordinary luminaire: - nominal voltage...: 6.11 (8.2.4) ortable luminaire: - protection independent of supporting surface - terminal block completely covered 6.11 (8.2.5) Compliance with the standard test finger or relevant probe 6.11 (8.2.6) Covers reliably secured 6.11 (8.2.7) Discharging of capacitors 0,5 μf Max. 0,225 μf Measured max. 18 V peak discharged voltage after 1 second. ortable plug connected luminaire with capacitor Other plug connected luminaire with capacitor Discharge device on or within capacitor Discharge device mounted separately 6.12 (12) ENDURANCE TEST AND THERMAL TEST 6.12 (12.3) Endurance test: 6.12a (-) - test voltage 1,1 Un (V)... : 264 V 6.12 (12.3) - mounting-position...: As normal use - test temperature ( C)...: 60 - total duration (h)...: supply voltage: Un factor; calculated voltage (V): 240 V x 1,1 = 264 V - lamp used...: Simulated diode 6.12 (12.3.2) After endurance test:

20 age 20 of 30 - no part unserviceable - luminaire not unsafe - no damage to track system - marking legible - no cracks, deformation etc (12.4) Thermal test (normal operation) (see Annex 2) 6.12b (-) - test voltage 1,06 Un (V)... : 1,06 x 240 V = 254,4 V 6.12 (12.5) Thermal test (abnormal operation) (see Annex 2) 6.12 (12.6) Thermal test (failed lamp control gear condition): 6.12 (12.6.1) Through wiring or looping-in wiring loaded by a current of (A)...: - case of abnormal conditions...: - electronic lamp control gear - measured winding temperature ( C): at 1,1 Un.: - measured mounting surface temperature ( C) at 1,1 Un...: - calculated mounting surface temperature ( C)..: - track-mounted luminaires 6.12 (12.6.2) Temperature sensing control - case of abnormal conditions...: - thermal link - manual reset cut-out - auto reset cut-out - measured mounting surface temperature ( C)...: - track-mounted luminaires 6.12 (12.7) Thermal test (failed lamp control gear in plastic luminaires): 6.12 (12.7.1) Luminaire without temperature sensing control 6.12 ( ) Luminaire with fluorescent lamp 70W Test method or Annex V...: Test according to : - case of abnormal conditions - Ballast failure at supply voltage (V)...: - Components retained in place after the test - Test with standard test finger after the test

21 age 21 of 30 Test according to Annex V: - case of abnormal conditions 6.12 ( ) - measured winding temperature ( C): at 1,1 Un..: - measured temperature of fixing point/exposed part ( C): at 1,1 Un...: - calculated temperature of fixing point/exposed part ( C)...: Ball-pressure test: - part tested; temperature ( C)...: - part tested; temperature ( C)...: Luminaire with discharge lamp, fluorescent lamp > 70W, transformer > 10 VA - case of abnormal conditions 6.12 ( ) - measured winding temperature ( C): at 1,1 Un..: - measured temperature of fixing point/exposed part ( C): at 1,1 Un...: - calculated temperature of fixing point/exposed part ( C)...: Ball-pressure test: - part tested; temperature ( C)...: - part tested; temperature ( C)...: Luminaire with short circuit proof transformers 10 VA - case of abnormal conditions - Components retained in place after the test - Test with standard test finger after the test 6.12 (12.7.2) Luminaire with temperature sensing control - thermal link Yes No - manual reset cut-out Yes No - auto reset cut-out Yes No - case of abnormal conditions - highest measured temperature of fixing point/exposed part ( C):...: Ball-pressure test: - part tested; temperature ( C)...: - part tested; temperature ( C)...:

22 age 22 of (9) RESISTANCE TO DUST, SOLID OBJECTS AND MOISTURE 6.13 (9.2) Tests for ingress of dust, solid objects and moisture: - classification according to I...: I20 - mounting position during test...: As normal use - fixing screws tightened; torque (Nm)...: 0,33 Nm - tests according to clauses...: Cl electric strength test afterwards a) no deposit in dust-proof luminaire b) no talcum in dust-tight luminaire c) no trace of water on current-carrying parts or SELV parts or where it could become a hazard d) i) For luminaires without drain holes no water entry d) ii) For luminaires with drain holes no hazardous water entry e) no water in watertight luminaire f) no contact with live parts (I 2X) f) no entry into enclosure (I 3X and I 4X) f) no contact with live parts (I3X and I4X) g) no trace of water on part of lamp requiring protection from splashing water h) no damage of protective shield or glass envelope 6.13 (9.3) Humidity test 48 h 25 C; 93% Rh 6.14 (10) INSULATION RESISTANCE AND ELECTRIC STRENGTH 6.14 (10.2.1) Insulation resistance test Cable or cord covered by metal foil or replaced by a metal rod of mm Ø...: Insulation resistance (MΩ) SELV: - between current-carrying parts of different polarity...: - between current-carrying parts and mounting surface...: > 100 MΩ

23 age 23 of 30 - between current-carrying parts and metal parts of the luminaire...: Other than SELV: > 100 MΩ - between live parts of different polarity...: > 100 MΩ - between live parts and mounting surface...: > 100 MΩ - between live parts and metal parts...: > 100 MΩ - between live parts of different polarity through action of a switch...: 6.14 (10.2.2) Electric strength test Dummy lamp Luminaires with ignitors after 24 h test Luminaires with manual ignitors Test voltage (V): SELV: - between current-carrying parts of different polarity...: - between current-carrying parts and mounting surface...: - between current-carrying parts and metal parts of the luminaire...: Other than SELV: 500 V 500 V - between live parts of different polarity...: 1480 V - between live parts and mounting surface...: 2960 V - between live parts and metal parts...: 2960 V - between live parts of different polarity through action of a switch...: 6.14 (10.3) Touch current (ma)...: 0,0061 ma peak (Limit: 0,7 ma peak) 6.15 (13) RESISTANCE TO HEAT, FIRE AND TRACKING 6.15 (13.2.1) Ball-pressure test: - part tested; temperature ( C)...: Refer to report GZ part tested; temperature ( C)...: 6.15 (13.3.1) Needle flame test (10 s): - part tested...: Refer to report GZ part tested...: 6.15 (13.3.2) Glow-wire test (650 C):

24 age 24 of 30 - part tested...: Refer to report GZ part tested...: 6.15 (13.4.1) Tracking test: part tested...: ANNEX 1: components (Refer to report GZ )

25 age 25 of 30 ANNEX 2: temperature measurements, thermal tests of Section 12 Type reference... : EI016C1400LS Lamp used... : Simulated diode Lamp control gear used... : EI016C1400LS Mounting position of luminaire... : Fixed as normal use in oven Supply wattage (W)... : 19,3 Supply current (A)... : 0,0885 Calculated power factor... : 0,85 Table: measured temperatures corrected for ta = 50 C: - abnormal operating mode... : Short circuited output - test 1: rated voltage... : 1) 1,0 x 240 = 240 V - test 2: 1,06 times rated voltage or 1,05 times rated wattage... : - test 3: Load on wiring to socket-outlet, 1,06 times voltage or 1,05 times wattage... : - test 4: 1,1 times rated voltage or 1,05 times rated wattage... : Through wiring or looping-in wiring loaded by a current of A during the test... : 2) 1,06 x 240 = 254,4 V 3) 1,1 x 240=264 V

26 age 26 of 30 temperature ( C) of part Clause 12.4 normal Clause 12.5 abnormal VC insulation of wiring (input) VC insulation of wiring (output) test 1 test 2 test 3 limit test 4^ limit Terminal block (output) 80 T110 External enclosure (side, near T1) External enclosure (near C12) T T80 tc point T80 Supports X2 capacitor (C1) 64 T Electrolyte capacitor (C3) 76 T Y1 capacitor (CY1) 106 T Electrolyte capacitor (C12) 88 T rimary winding of transformer (T1) Secondary winding of transformer (T1) Bobbin of transformer (T1) 113 Ref. Inner surface of enclosure (near T1 and D7) 90 Ref. ^ Remark: Temperature for all monitored positions in tested sample was dropped to ambient temperature sharply when abnormal operating mode (short circuited output) was conducted to the tested sample.

27 age 27 of 30 ANNEX 3: screw terminals (part of the luminaire) (14) SCREW TERMINALS ANNEX 4: screwless terminals (part of the luminaire) (15) SCREWLESS TERMINALS CENELEC COMMON MODIFICATIONS (EN) 6.5 (3) MARKING 6.5 ( ) Adequate warning on the package 6.10 (5) EXTERNAL AND INTERNAL WIRING 6.10 (5.2.1) Connecting leads - without a means for connection to the supply - terminal block specified - relevant information provided - compliance with 4.6, 4.7.1, 4.7.2, , 11.2, 12 and 13.2 of art (5.2.2) Cables equal to HD21 S2 or HD22 S2 ZB ANNEX ZB, SECIAL NATIONAL CONDITIONS (EN) Not checked (3.3) DK: power supply cord with label Not checked IT: warning label on Class 0 luminaire Not checked (4.5.1) DK: socket-outlets Not checked (5.2.1) CY, DK, FI, SE, GB: type of plug Not checked ZC ANNEX ZC, NATIONAL DEVIATIONS (EN) Not checked (4 & 5) FR: Shuttered socket-outlets 10/16A Not checked (13.3) GB: Requirements according to United Kingdom Building Regulation Not checked

28 age 28 of 30 (13.3.2) FR: Glow-wire test 850 C alt. 750 C for luminaires in premises open to public or 960 C for luminaires in emergency exits Not checked

29 Appendix I: model list age 29 of 30