TEST REPORT EN Luminaires Part 2: Particular requirements: Section One Fixed general purpose luminaires

Transcription

1 TEST REORT EN Luminaires art 2: articular requirements: Section One Fixed general purpose luminaires Report Reference No...: QUA/LI Date of issue...: Total number of pages pages CB Testing Laboratory...: Address...: Applicant s name...: Address...: DEKRA Certification Hong Kong Limited Unit 1-14, 6/F., Fuk Shing Commercial Building, 28 On Lok Mun Street, On Lok Tsuen, Fanling, N.T., Hong Kong Matrix Lighting Limited Room , 2/F., East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong. Test specification: Standard...: Test procedure...: Non-standard test method..: EN :1989 used in conjunction with EN : A11:2009; AS/NZS :1998 used in conjunction with AS/NZS :2003 LVD Test Report Form No...: Test Report Form(s) Originator...: Master TRF...: IEC60598_2_1B Intertek Semko AB Copyright 2009 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. If this Test Report Form is used by non-iecee members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.

2 age 2 of 51 Report No.: QUA/LI Test item description...: Trade Mark...: Manufacturer...: Factory...: Model/Type reference...: Ratings...: 5 Feet LED tube VIRIBRIGHT Matrix Lighting Limited 1) Zhong Shan Ban Fu Micami Toys Factory Sha Guo Industrial Zone, Ban Fu Country, ZhongShan City, Guangdong rovince, China 2) ZhongShan Wei Heng lastic Industry Co.,Ltd. 172 North Banfu Road, Banfu town, Zhongshan, Guangdong, China T8-150EU Vac; 50 / 60 Hz; 150 ma; 25 W; G13

3 age 3 of 51 Report No.: QUA/LI Testing procedure and testing location: Testing Laboratory: DEKRA Certification Hong Kong Limited Testing location/ address...: Unit 1-14, 6/F., Fuk Shing Commercial Building, 28 On Lok Mun Street, On Lok Tsuen, Fanling, N.T., Hong Kong Associated CB Laboratory: Testing location/ address...: Tested by (name + signature)...: Roy Yip Approved by (+ signature)...: Jimmy Chu Testing procedure: TM Tested by (name + signature)...: Approved by (+ signature)...: Testing location/ address...: Testing procedure: WMT Tested by (name + signature)...: Witnessed by (+ signature)...: Approved by (+ signature)...: Testing location/ address...: Testing procedure: SMT Tested by (name + signature)...: Approved by (+ signature)...: Supervised by (+ signature)...: Testing location/ address...: Testing procedure: RMT Tested by (name + signature)...: Approved by (+ signature)...: Supervised by (+ signature)...: Testing location/ address...:

4 age 4 of 51 Report No.: QUA/LI Summary of testing: Tests performed (name of test and test clause): EN :1989 used in conjunction with EN : A11:2009 AS/NZS :1998 used in conjunction with AS/NZS :2003 Testing location: DEKRA Certification Hong Kong Limited Unit 1-14, 6/F., Fuk Shing Commercial Building, 28 on Lok Mun Street, On Lok Tsuen, Fanling, N.T. Hong Kong LED driver inside the tubes was additionally tested according with EN :2006 used in conjunction with EN :2008 The 5 Feet LED tube was tested according EN The model: T8-150EU (3000 K) and T8-150EU (5600 K) are selected for the test, which can represent all models. Model: T8-150EU (3000 K) and T8-150EU (5600 K) have been tested and classified as Exempt Group. Summary of compliance with National Differences: The samples tested comply with the requirements of EN standard. Australia national deviation of AS/NZS was applied. See details in page Copy of marking plate

5 age 5 of 51 Report No.: QUA/LI Test item particulars... : 5 Feet LED tube Classification of installation and use... : Class II semi-luminaire Supply Connection... : G13 lampholder... :... : ossible test case verdicts: - test case does not apply to the test object... : (Not applicable) - test object does meet the requirement... : (ass) - test object does not meet the requirement... : F (Fail) Testing... : Date of receipt of test item... : Date (s) of performance of tests... : to General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Throughout this report a comma (point) is used as the decimal separator. Clause numbers between brackets refer to clauses in EN General product information: 5 Feet LED tube with integral LED driver. Models Rating Total length Color of LED T8-150EU V; 50 / 60 Hz; 150 ma; 25 W; G13 1,5 m 3000 K; 4000 K; 5600 K NOTE: Clear installation instruction and warnings are provided with the products.

6 age 6 of 51 EN (0) GENERAL TEST REQUIREMENTS 1.2 (0.1) Information for luminaire design considered Standard Yes No 1.2 (0.3) More sections applicable...: Yes No 1.4 (2) CLASSIFICATION 1.4 (2.2) Type of protection (Class 0 excluded)... : Class II 1.4 (2.3) Degree of protection (Requirement: Ordinary)... : I (2.4) Luminaire suitable for direct mounting on normally flammable surfaces... : Luminaire not suitable for direct mounting on normally flammable surfaces... : Yes No Yes No 1.4 (2.5) Luminaire for normal use... : Yes No Luminaire for rough service... : Yes No 1.5 (3) MARKING 1.5 (3.2) Mandatory markings osition of the marking Format of symbols/text 1.5 (3.3) Additional information Language of instructions 1.5 (3.3.1) Combination luminaires 1.5 (3.3.2) Nominal frequency in Hz 50/60 Hz 1.5 (3.3.3) Operating temperature 1.5 (3.3.4) Symbol or warning notice 1.5 (3.3.5) Wiring diagram 1.5 (3.3.6) Special conditions 1.5 (3.3.7) Metal halide lamp luminaire warning 1.5 (3.3.8) Limitation for semi-luminaires 1.5 (3.3.9) ower factor and supply current 1.5 (3.3.10) Suitability for use indoors 1.5 (3.3.11) Luminaires with remote control 1.5 (3.3.12) Clip-mounted luminaire warning

7 age 7 of 51 EN (3.3.13) Specifications of protective shields 1.5 (3.3.14) Symbol for nature of supply 1.5 (3.3.15) Rated current of socket outlet 1.5 (3.3.16) Rough service luminaire 1.5 (3.3.17) Mounting instruction for type Y, type Z and some type X attachments 1.5 (3.3.18) Non-ordinary luminaires with VC cable 1.5 (3.3.19) rotective conductor current in instruction if applicable 1.5 (3.3.20) rovided with information if not intended to be mounted within arms reach 1.5 (3.4) Test with water Test with hexane Legible after test Label attached 1.6 (4) CONSTRUCTION 1.6 (4.2) Components replaceable without difficulty 1.6 (4.3) Wireways smooth and free from sharp edges 1.6 (4.4) Lampholders 1.6 (4.4.1) Integral lampholder 1.6 (4.4.2) Wiring connection 1.6 (4.4.3) Lampholder for end-to-end mounting 1.6 (4.4.4) ositioning - pressure test (N)... : After test the lampholder comply with relevant standard sheets and show no damage After test on single-capped lampholder the lampholder have not moved from its position and show no permanent deformation - bending test (N)... : After test the lampholder have not moved from its position and show no permanent deformation 1.6 (4.4.5) eak pulse voltage 1.6 (4.4.6) Centre contact

8 age 8 of 51 EN (4.4.7) arts in rough service luminaires resistant to tracking 1.6 (4.4.8) Lamp connectors 1.6 (4.4.9) Caps and bases correctly used 1.6 (4.5) Starter holders Starter holder in luminaires other than class II Starter holder class II construction 1.6 (4.6) Terminal blocks Tails Unsecured blocks 1.6 (4.7) Terminals and supply connections 1.6 (4.7.1) Contact to metal parts 1.6 (4.7.2) Test 8 mm live conductor Test 8 mm earth conductor 1.6 (4.7.3) Terminals for supply conductors 1.6 ( ) Welded connections: - stranded or solid conductor - spot welding - welding between wires - Type Z attachment - mechanical test according to electrical test according to heat test according to and (4.7.4) Terminals other than supply connection 1.6 (4.7.5) Heat-resistant wiring/sleeves 1.6 (4.7.6) Multi-pole plug - test at 30 N 1.6 (4.8) Switches: - adequate rating - adequate fixing - polarized supply - compliance with for electronic switches 1.6 (4.9) Insulating lining and sleeves

9 age 9 of 51 EN (4.9.1) Retainment Method of fixing... : Heat shrinkage 1.6 (4.9.2) Insulated linings and sleeves Resistant to a temperature > 20 C to the wire temperature or a) & c) Insulation resistance and electric strength b) Ageing test. Temperature ( C)... : 1.6 (4.10) Insulation of Class II luminaires 1.6 (4.10.1) No contact, mounting surface accessible metal parts wiring of basic insulation Safe installation fixed luminaires Capacitors and switches Interference suppression capacitors according to IEC (4.10.2) Assembly gaps: - not coincidental - no straight access with test probe 1.6 (4.10.3) Retainment of insulation: - fixed - unable to be replaced; luminaire inoperative - sleeves retained in position - lining in lampholder 1.6 (4.11) Electrical connections 1.6 (4.11.1) Contact pressure 1.6 (4.11.2) Screws: - self-tapping screws - thread-cutting screws 1.6 (4.11.3) Screw locking: - spring washer - rivets 1.6 (4.11.4) Material of current-carrying parts 1.6 (4.11.5) No contact to wood or mounting surface 1.6 (4.11.6) Electro-mechanical contact systems 1.6 (4.12) Mechanical connections and glands

10 age 10 of 51 EN (4.12.1) Screws not made of soft metal Screws of insulating material Torque test: torque (Nm); part... : Torque test: torque (Nm); part... : Torque test: torque (Nm); part... : 1.6 (4.12.2) Screws with diameter < 3 mm screwed into metal 1.6 (4.12.4) Locked connections: - fixed arms; torque (Nm)... : - lampholder; torque (Nm)... : - push-button switches; torque 0,8 Nm... : 1.6 (4.12.5) Screwed glands; force (Nm)... : 1.6 (4.13) Mechanical strength 1.6 (4.13.1) Impact tests: - fragile parts; energy (Nm)... : - other parts; energy (Nm)... : 0,35 Nm 1) live parts 2) linings 3) protection 4) covers 1.6 (4.13.3) Straight test finger 1.6 (4.13.4) Rough service luminaires - I54 or higher a) fixed b) hand-held c) delivered with a stand d) for temporary installations and suitable for mounting on a stand 1.6 (4.13.6) Tumbling barrel 1.6 (4.14) Suspensions and adjusting devices 1.6 (4.14.1) Mechanical load: A) four times the weight B) torque 2,5 Nm C) bracket arm; bending moment (Nm)... :

11 age 11 of 51 EN D) load track-mounted luminaires E) clip-mounted luminaires, glass-shelve. Thickness (mm)... : Metal rod. diameter (mm)... : Fixed luminaire or independent control gear without fixing devices 1.6 (4.14.2) Load to flexible cables Mass (kg)... : Stress in conductors (N/mm²)... : Mass (kg) of semi-luminaire... : Bending moment (Nm) of semi-luminaire... : 1.6 (4.14.3) Adjusting devices: - flexing test; number of cycles... : - strands broken - electric strength test afterwards 1.6 (4.14.4) Telescopic tubes: cords not fixed to tube; no strain on conductors 1.6 (4.14.5) Guide pulleys 1.6 (4.14.6) Strain on socket-outlets 1.6 (4.15) Flammable materials: - glow-wire test 650 C - spacing 30 mm - screen withstanding test of screen dimensions - no fiercely burning material - thermal protection - electronic circuits exempted 1.6 (4.15.2) Luminaires made of thermoplastic material with lamp control gear a) construction b) temperature sensing control c) surface temperature 1.6 (4.16) Luminaires for mounting on normally flammable surfaces No lamp control gear (compliance with Section 12) 1.6 (4.16.1) Lamp control gear spacing:

12 age 12 of 51 EN spacing 35 mm - spacing 10 mm 1.6 (4.16.2) Thermal protection: - in lamp control gear - external - fixed position - temperature marked lamp control gear 1.6 (4.16.3) Design to satisfy the test of 12.6 (see 12.6) 1.6 (4.17) Drain holes Clearance at least 5 mm 1.6 (4.18) Resistance to corrosion: 1.6 (4.18.1) - rust-resistance 1.6 (4.18.2) - season cracking in copper 1.6 (4.18.3) - corrosion of aluminium 1.6 (4.19) Ignitors compatible with ballast 1.6 (4.20) Rough service vibration 1.6 (4.21) rotective shield: 1.6 (4.21.1) Shield fitted Shield of glass if tungsten halogen lamps 1.6 (4.21.2) articles from a shattering lamp not impair safety 1.6 (4.21.3) No direct path 1.6 (4.21.4) Impact test on shield Glow-wire test on lamp compartment 1.6 (4.22) Attachments to lamps 470,1g 1.6 (4.23) Semi-luminaires comply Class II 1.6 (4.24) UV radiation for tungsten halogen lamps and metal halide lamps (Annex ) 1.6 (4.25) No sharp point or edges 1.6 (4.26) Short-circuit protection: 1.6 (4.26.1) Uninsulated accessible SELV parts 1.6 (4.26.2) Short-circuit test 1.6 (4.26.3) Test chain according to Figure 29

13 age 13 of 51 EN (11) CREEAGE DISTANCES AND CLEARANCES Working voltage (V)... : V Voltage form Sinusoidal Non-sinusoidal TI < 600 > 600 Impulse withstand category (Normal category II) (Category III Annex U) Rated pulse voltage (kv)... : Category II Category III (1) Current-carrying parts of different polarity: cr (mm); cl (mm)... : (2) Current-carrying parts and accessible parts: cr (mm); cl (mm)... : (3) arts becoming live due to breakdown of basic insulation and metal parts: cr (mm); cl (mm)... : (4) Outer surface of cable where it is clamped and metal parts: cr (mm); cl (mm)... : Cr => 2,5 mm Cl => 1,5 mm Cr => 5,0 mm Cl => 3 mm Cr => 2,5 mm Cl => 1,5 mm (5) Not used (6) Current-carrying parts and supporting surface: cr (mm); cl (mm)... : Cr => 5,0 mm Cl => 3 mm 1.8 (7) ROVISION FOR EARTHING 1.8 ( ) 1.8 ( ) Accessible metal parts Metal parts in contact with supporting surface Resistance < 0,5 Ω Self-tapping screws used Thread-forming screws Thread-forming screw used in a grove Earth makes contact first Earth continuity in joints etc. 1.8 (7.2.4) Locking of clamping means Compliance with Terminal blocks with integrated screwless earthing contacts tested according Annex V

14 age 14 of 51 EN (7.2.5) Earth terminal integral part of connector socket 1.8 (7.2.6) Earth terminal adjacent to mains terminals 1.8 (7.2.7) Electrolytic corrosion of the earth terminal 1.8 (7.2.8) Material of earth terminal Contact surface bare metal 1.8 (7.2.10) Class II luminaire for looping-in Double or reinforced insulation to functional earth 1.8 (7.2.11) Earthing core coloured green-yellow Length of earth conductor 1.9 (14) SCREW TERMINALS Separately approved; component list (see Annex 1) art of the luminaire (see Annex 3) 1.9 (15) SCREWLESS TERMINALS AND ELECTRICAL CONNECTIONS Separately approved; component list (see Annex 1) art of the luminaire (see Annex 4) 1.10 (5) EXTERNAL AND INTERNAL WIRING 1.10 (5.2) Supply connection and external wiring 1.10 (5.2.1) Means of connection... : G13 caps 1.10 (5.2.2) Type of cable... : Nominal cross-sectional area (mm²)... : Cables equal to IEC or IEC (5.2.3) Type of attachment, X, Y or Z 1.10 (5.2.5) Type Z not connected to screws 1.10 (5.2.6) Cable entries: - suitable for introduction - adequate degree of protection 1.10 (5.2.7) Cable entries through rigid material have rounded edges 1.10 (5.2.8) Insulating bushings: - suitably fixed

15 age 15 of 51 EN material in bushings - material not likely to deteriorate - tubes or guards made of insulating material 1.10 (5.2.9) Locking of screwed bushings 1.10 (5.2.10) Cord anchorage: 1.10 ( ) 1.10 ( ) 1.10 ( ) - covering protected from abrasion - clear how to be effective - no mechanical or thermal stress - no tying of cables into knots etc. - insulating material or lining Cord anchorage for type X attachment: a) at least one part fixed b) types of cable c) no damaging of the cable d) whole cable can be mounted e) no touching of clamping screws f) metal screw not directly on cable g) replacement without special tool Glands not used as anchorage Labyrinth type anchorages Adequate cord anchorage for type Y and type Z attachment Tests: - impossible to push cable; unsafe - pull test: 25 times; pull (N)... : - torque test: torque (Nm)... : - displacement 2 mm - no movement of conductors - no damage of cable or cord 1.10 (5.2.11) External wiring passing into luminaire 1.10 (5.2.12) Looping-in terminals 1.10 (5.2.13) Wire ends not tinned

16 age 16 of 51 EN Wire ends tinned: no cold flow 1.10 (5.2.14) Mains plug same protection Class III luminaire plug 1.10 (5.2.16) Appliance inlets (IEC 60320) Appliance couplers of class II type 1.10 (5.2.17) No standardized interconnecting cables properly assembled 1.10 (5.2.18) Used plug in accordance with - IEC other standard 1.10 (5.3) Internal wiring 1.10 (5.3.1) Internal wiring of suitable size and type Through wiring - not delivered/ mounting instruction - factory assembled - socket outlet loaded (A)... : - temperatures... : (see Annex 2) Green-yellow for earth only 1.10 ( ) Internal wiring connected directly to fixed wiring Cross-sectional area (mm²)... : Insulation thickness Extra insulation added where necessary 1.10 ( ) Internal wiring connected to fixed wiring via internal current-limiting device Adequate cross-sectional area and insulation thickness 0,34 mm² 1.10 ( ) Double or reinforced insulation for class II 1.10 ( ) Conductors without insulation 1.10 ( ) SELV current-carrying parts 1.10 ( ) Insulation thickness other than VC or rubber 1.10 (5.3.2) Sharp edges etc. No moving parts of switches etc. Joints, raising/lowering devices Telescopic tubes etc. No twisting over 360

17 age 17 of 51 EN (5.3.3) Insulating bushings: - suitable fixed - material in bushings - material not likely to deteriorate - cables with protective sheath 1.10 (5.3.4) Joints and junctions effectively insulated 1.10 (5.3.5) Strain on internal wiring 1.10 (5.3.6) Wire carriers 1.10 (5.3.7) Wire ends not tinned Wire ends tinned: no cold flow 1.11 (8) ROTECTION AGAINST ELECTRIC SHOCK 1.11 (8.2.1) Live parts not accessible with standard test finger Basic insulated parts not used on the outer surface without appropriate protection Basic insulated parts not accessible with standard test finger on portable and adjustable luminaires Basic insulated parts not accessible with Ø 50 mm probe from outside, within arms reach, on wall-mounted luminaires Lamp and starterholders in portable and adjustable luminaires comply with double or reinforced insulation requirements Basic insulation only accessible under lamp or starter replacement rotection in any position Double-ended tungsten filament lamp Insulation lacquer not reliable Double-ended high pressure discharge lamp Relevant warning according to fitted to the luminaire 1.11 (8.2.2) ortable luminaire adjusted in most unfavourable position 1.11 (8.2.3.a) Class II luminaire: - basic insulated metal parts not accessible during starter or lamp replacement

18 age 18 of 51 EN basic insulation not accessible other than during starter or lamp replacement - glass protective shields not used as supplementary insulation 1.11 (8.2.3.b) BC lampholder of metal in class I luminaires shall be earthed 1.11 (8.2.3.c) Class III luminaires with exposed SELV parts: Ordinary luminaire: - touch current... : - no-load voltage... : Other than ordinary luminaire: - nominal voltage... : 1.11 (8.2.4) ortable luminaire: - protection independent of supporting surface - terminal block completely covered 1.11 (8.2.5) Compliance with the standard test finger or relevant probe 1.11 (8.2.6) Covers reliably secured 1.11 (8.2.7) Discharging of capacitors 0,5 µf ortable plug connected luminaire with capacitor Other plug connected luminaire with capacitor Discharge device on or within capacitor Discharge device mounted separately 1.12 (12) ENDURANCE TEST AND THERMAL TEST 1.12 (12.3) Endurance test: - mounting-position... : Normal - test temperature ( C)... : 35 C - total duration (h)... : 240 hours - supply voltage: Un factor; calculated voltage (V): 264 V - lamp used... : Enclosed LED 1.12 (12.3.2) After endurance test: - no part unserviceable - luminaire not unsafe

19 age 19 of 51 EN no damage to track system - marking legible - no cracks, deformation etc (12.4) Thermal test (normal operation) (see Annex 2) 1.12 (12.5) Thermal test (abnormal operation) (see Annex 2) 1.12 (12.6) Thermal test (failed lamp control gear condition): 1.12 (12.6.1) Through wiring or looping-in wiring loaded by a current of (A)... : - case of abnormal conditions... : - electronic lamp control gear - measured winding temperature ( C): at 1,1 Un. : - measured mounting surface temperature ( C) at 1,1 Un... : - calculated mounting surface temperature ( C).. : - track-mounted luminaires 1.12 (12.6.2) Temperature sensing control - case of abnormal conditions... : - thermal link - manual reset cut-out - auto reset cut-out - measured mounting surface temperature ( C)... : - track-mounted luminaires 1.12 (12.7) Thermal test (failed lamp control gear in plastic luminaires): 1.12 (12.7.1) Luminaire without temperature sensing control 1.12 ( ) Luminaire with fluorescent lamp 70W Test method or Annex V... : Test according to : - case of abnormal conditions - Ballast failure at supply voltage (V)... : - Components retained in place after the test - Test with standard test finger after the test Test according to Annex V: - case of abnormal conditions

20 age 20 of 51 EN measured winding temperature ( C): at 1,1 Un.. : - measured temperature of fixing point/exposed part ( C): at 1,1 Un... : 1.12 ( ) - calculated temperature of fixing point/exposed part ( C)... : Ball-pressure test: - part tested; temperature ( C)... : - part tested; temperature ( C)... : Luminaire with discharge lamp, fluorescent lamp > 70W, transformer > 10 VA - case of abnormal conditions 1.12 ( ) - measured winding temperature ( C): at 1,1 Un.. : - measured temperature of fixing point/exposed part ( C): at 1,1 Un... : - calculated temperature of fixing point/exposed part ( C)... : Ball-pressure test: - part tested; temperature ( C)... : - part tested; temperature ( C)... : Luminaire with short circuit proof transformers 10 VA - case of abnormal conditions - Components retained in place after the test - Test with standard test finger after the test 1.12 (12.7.2) Luminaire with temperature sensing control - thermal link Yes No - manual reset cut-out Yes No - auto reset cut-out Yes No - case of abnormal conditions - highest measured temperature of fixing point/exposed part ( C):... : Ball-pressure test: - part tested; temperature ( C)... : - part tested; temperature ( C)... :

21 age 21 of 51 EN (9) RESISTANCE TO DUST, SOLID OBJECTS AND MOISTURE 1.13 (9.2) Tests for ingress of dust, solid objects and moisture: - classification according to I... : I20 - mounting position during test... : Normal - fixing screws tightened; torque (Nm)... : - tests according to clauses... : electric strength test afterwards a) no deposit in dust-proof luminaire b) no talcum in dust-tight luminaire c) no trace of water on current-carrying parts or SELV parts or where it could become a hazard d) i) For luminaires without drain holes no water entry d) ii) For luminaires with drain holes no hazardous water entry e) no water in watertight luminaire f) no contact with live parts (I 2X) f) no entry into enclosure (I 3X and I 4X) f) no contact with live parts (I3X and I4X) g) no trace of water on part of lamp requiring protection from splashing water h) no damage of protective shield or glass envelope 1.13 (9.3) Humidity test 48 h 23 C 93 % 1.14 (10) INSULATION RESISTANCE AND ELECTRIC STRENGTH 1.14 (10.2.1) Insulation resistance test Cable or cord covered by metal foil or replaced by a metal rod of mm Ø... : Insulation resistance (MΩ) SELV: - between current-carrying parts of different polarity... : - between current-carrying parts and mounting surface... :

22 age 22 of 51 EN between current-carrying parts and metal parts of the luminaire... : Other than SELV: - between live parts of different polarity... : - between live parts and mounting surface... : 99 GΩ - between live parts and metal parts... : 99 GΩ - between live parts of different polarity through action of a switch... : 1.14 (10.2.2) Electric strength test Dummy lamp Luminaires with ignitors after 24 h test Luminaires with manual ignitors Test voltage (V): SELV: - between current-carrying parts of different polarity... : - between current-carrying parts and mounting surface... : - between current-carrying parts and metal parts of the luminaire... : Other than SELV: - between live parts of different polarity... : - between live parts and mounting surface... : 2960 V - between live parts and metal parts... : 2960 V - between live parts of different polarity through action of a switch... : 1.14 (10.3) Touch current (ma)... : 0,0068 ma 1.15 (13) RESISTANCE TO HEAT, FIRE AND TRACKING 1.15 (13.2.1) Ball-pressure test: - part tested; temperature ( C)... : Lamp cap; 125 C; 1,15 mm - part tested; temperature ( C)... : Lampholder terminal; 125 C; 1,29 mm - part tested; temperature ( C)... : LED CB; 125 C; 1,18 mm - part tested; temperature ( C)... : Main CB; 125 C; 0,77 mm

23 age 23 of 51 EN (13.3.1) Needle flame test (10 s): - part tested... : Lamp cap - part tested... : Lampholder terminal - part tested... : LED CB - part tested... : Main CB 1.15 (13.3.2) Glow-wire test (650 C): - part tested... : LED CB - part tested... : Main CB - part tested... : Lamp cover - part tested... : Tube enclosure 1.15 (13.4.1) Tracking test: part tested... :

24 age 24 of 51 EN ANNEX 1: components object/part No. code manufacturer/ trademark type/model technical data standard mark(s) of conformity Lamp cap C ZhongShan Wei Heng LED driver C ZhongShan Wei Heng G13 -- EN Tested in appliance EN Tested in appliance Internal wire C Zhongshan Ruihua AWG 300 V 80 C, double layer EN Tested in appliance Fuse B XC electronics (Shen Zhen) Varistor B Brightking (Shenzhen) / Jomnspge 3F-Series 250 V 1 A EN , EN D471K 2,5 A IEC , IEC VDE VDE LED C - ES-CEDBV10F InGaN Venus Blue LED Chip IEC Test with appliance The codes above have the following meaning: A - The component is replaceable with another one, also certified, with equivalent characteristics B - The component is replaceable if authorised by the test house C - Integrated component tested together with the appliance D - Alternative component

25 age 25 of 51 EN ANNEX 2: temperature measurements, thermal tests of Section 12 Type reference...: T8-150EU Lamp used...: Enclosed LED Lamp control gear used...: Integral Mounting position of luminaire...: Mounted in luminaire Supply wattage (W)...: 254,4 W Supply current (A)...: 128,5 ma Calculated power factor...: 0,748 Table: measured temperatures corrected for ta = 25 C: - abnormal operating mode...: -- - test 1: rated voltage...: -- - test 2: 1,06 times rated voltage or 1,05 times rated wattage...: - test 3: Load on wiring to socket-outlet, 1,06 times voltage or 1,05 times wattage...: - test 4: 1,1 times rated voltage or 1,05 times rated wattage...: Through wiring or looping-in wiring loaded by a current of A during the test...: 1,06 x 240 V temperature ( C) of part Clause 12.4 normal Clause 12.5 abnormal test 1 test 2 test 3 limit test 4 limit Capacitor C , Capacitor C , Varistor -- 52, Internal wire -- 44, Housing -- 62, Lamp cap -- 38, LED -- 57,1 -- Ref Lamp cap terminal -- 54, Mounting surface -- 28,

26 age 26 of 51 EN ANNEX 3: screw terminals (part of the luminaire) (14) SCREW TERMINALS ANNEX 4: screwless terminals (part of the luminaire) (15) SCREWLESS TERMINALS ANNEX 5: National Differences for (country name) or Group Differences CENELEC COMMON MODIFICATIONS (EN) 1.5 (3) MARKING 1.5 ( ) Adequate warning on the package 1.10 (5) EXTERNAL AND INTERNAL WIRING 1.10 (5.2.1) Connecting leads - without a means for connection to the supply - terminal block specified - relevant information provided - compliance with 4.6, 4.7.1, 4.7.2, , 11.2, 12 and 13.2 of art (5.2.2) Cables equal to HD21 S2 or HD22 S2 ZB ANNEX ZB, SECIAL NATIONAL CONDITIONS (EN) (3.3) DK: power supply cord with label IT: warning label on Class 0 luminaire (4.5.1) DK: socket-outlets (5.2.1) CY, DK, FI, SE, GB: type of plug ZC ANNEX ZC, NATIONAL DEVIATIONS (EN) (4 & 5) FR: Shuttered socket-outlets 10/16A (13.3) DK: Needle flame test during 30 s (13.3) GB: Requirements according to United Kingdom Building Regulation (13.3.2) FR: Glow-wire test 850 C alt. 750 C for luminaires in premises open to public or 960 C for luminaires in emergency exits

27 age 27 of 51 EN ZZ ANNEX ZZ AS/NZS ZZ1 Introduction ZZ2 Variations 1.1 (0) SCOE 1.1 (0.2) Normative references 1.1 (0.4.2) Rated voltage of 240V / 415V 240V 1.1 (1.2.41) Flammable material 1.1 (1.2.62) Mains socket-outlet-mounted luminaire 1.4 (2) CLASSIFICATION 1.4(2.2) Type of protection (restricted)... : Class II 1.5 (3) MARKING 1.5 (3.2) Mandatory markings 1.5 (3.3) Additional information Language of instruction English 1.5 (3.3.10) Indoor and outdoor use 1.6 (4) CONSTRUCTION 1.6 (4.4.1) G5 lampholder 1.6 (4.16) Luminaires for mounting on normally flammable surface No lamp control gear 1.7 (11) CREEAGE DISTANCES AND CLEARANCES 1.9 (14) SCREW TERMINALS 1.9 (15) SCREWLESS TERMINALS 1.10 (5) EXTERNAL AND INTERNAL WIRING 1.10 (5.2.1) Non-detachable cables or cords (5.2.2) 1.10 (5.2.16) Type of cable... : Nominal cross-sectional area (mm²)... : Installation couplers 1.11 (8) ROTECTION AGAINST ELECTRIC SHOCK 1.11 (8.2.1) G5 lampholder 1.11 (8.2.4) ortable luminaire: - Class I portable luminaires and luminaires for wall mounting within arm s reach and terminal block 1.12 (12) ENDURANCE TEST AND THERMAL TEST 1.13 (9) RESISTANCE TO DUST, SOLID OBJECTS AND MOISTURE 1.14 (10) INSULATION RESISTANCE AND ELECTRIC STRENGTH

28 age 28 of 51 EN (13) RESISTANCE TO HEAT, FIRE AND TRACKING 1.15 (13.3.1) 1.15 (13.3.2) 1.15 (13.3.3) Glow wire test (750 C): Glow wire test (650 C): Needle flame test (30 s): lamp cover; tube enclosure; CB

29 age 29 of 51 EN (4) GENERAL REQUIREMENTS Compliance of independent controlgear enclosure with EN Independent SELV controlgear comply with Annex I (see Annex I) 6 (6) CLASSIFICATION Independent controlgear... : Yes No Built-in controlgear... : Yes No Integral controlgear... : Yes No SELV-equivalent or isolating controlgear... : Yes No Auto-wound controlgear... : Yes No Independent SELV controlgear... : Yes No 7 MARKING 7.1 (7.1) Mandatory markings: - mark of origin - model number, type reference... : - symbol for independent controlgear, if applicable - correlation between interchangeable parts and controlgear marked - rated supply voltage (V)... : - earthing symbol - wiring diagram - value of t c - symbol for declared temperature Constant voltage type: Yes No - rated supply voltage (V)... : Constant current type: Yes No - rated output current (A)... : - rated maximum output voltage (V)... : - indication if for LED modules only 7.2 (7.1) - information to be provided, if applicable - declaration on protection against accidental contact

30 age 30 of 51 EN cross-section of conductors (mm²)... : - number, type and wattage of lamp(s) - directly mains-connected windings SELV-equivalent controlgear - (7.2) Marking durable and legible Rubbing 15 s water, 15 s petroleum; marking legible 8 (10) ROTECTION AGAINST ACCIDENTAL CONTACT WITH LIVE ARTS - (10.1) Controlgear protected against accidental contact with live parts - (A2) The current flowing between the part concerned and earth is measured and does not exceed 0,7 ma (peak) or 2 ma d.c.... : 0,1 ma - (A2) For frequencies above 1 khz, the current does not exceed 0,7 ma (peak) multiplied by the value of the frequency in kilohertz or 70 ma (peak)... : - (A3) The voltage between the part concerned and any accessible part is measured and does not exceed 34 V (peak)... : - (10.1) Lacquer or enamel not used for protection or insulation Adequate mechanical strength on parts providing protection - (10.2) Capacitors > 0,5 µf: voltage after 1 min (V): < 50 V: 0,04 V 8.1 (-) SELV-equivalent controlgear accessible parts are insulated from live parts by double or reinforced insulation according 8.6 and 13.1 in IEC (-) Exposed terminals of SELV or SELV-equivalent controlgear are allowed if: - the rated or maximum output voltage does not exceeding 25 V r.m.s. - the no-load output voltage does not exceed 30 V r.m.s. or 33 2 V peak Insulated terminals if rated output voltage >25 V

31 age 31 of 51 EN One capacitor Y1 or two capacitors Y2 of the same values used in series between SELV or SELVequivalent output and primary circuits - Capacitor complying with IEC Other components bridging the separating transformer complying with IEC 60065, clause 14 9 (8) TERMINALS Screw terminals: compliance with Section 14 of IEC Screwless terminals: compliance with Section 15 of IEC (9) ROVISION FOR EARTHING External metal parts connected to the earthterminal: - compliance with in IEC Test with a current of 10 A between earthing terminal and each of the accessible metal parts; measured resistance (Ω): < 0,5 Ω... : rotective earth, symbol Terminal complying with clause 8 in art 1 Locked against loosening and not possible to loosen by hand Not possible to loosen clamping means unintentionally on screwless terminals Earthing via means of fixing Earthing terminal only used for the earthing of the control gear All parts of material minimizing the danger of electrolytic corrosion Made of brass or equivalent material Contact surface bare metal Conductors by tracks on printed circuit boards: - a.c. current of 25 A for 1 min between earthing terminal and accessible metal parts - compliance with clause in IEC

32 age 32 of 51 EN (11) MOISTURE RESISTANCE AND INSULATION After storage 48 h at 91-95% relative humidity and C measuring of insulation resistance with d.c. 500 V (MΩ): 2 MΩ for basic insulation... : 4 MΩ for double or reinforced insulation... : 99 GΩ 11 (-) Adequate insulation between input and output terminals not bounded together in SELV-equivalent controlgear 12 (12) ELECTRIC STRENGTH Immediately after clause 11 electric strength test for 1 min Working voltage 42 V, test voltage 500 V Working voltage > 42 V 1000 V, test voltage (V): Basic insulation, 2U V Supplementary insulation, 2U V Double or reinforced insulation, 2U V No flashover or breakdown Windings in separating transformers in SELVequivalent control gear according to of EN (13) THERMAL ENDURANCE FOR WINDINGS (Not applicable) 14 (14) FAULT CONDITIONS When operated under fault conditions the controlgear: - does not emit flames or molten material - does not produce flammable gases - protection against accidental contact not impaired Thermally protected controlgear does not exceed the marked temperature value Fault conditions: capacitors, resistors or inductors without proof of compliance with relevant specifications have been short-circuited or disconnected - (14.1) Short-circuit of creepage distances and clearances if less than specified in clause 16 in art 1 (except between live parts and accessible metal parts) (see appended table) (see appended table)

33 age 33 of 51 EN Distances on printed boards provided with coating according to IEC (14.2) Short-circuit or interruption of semiconductor devices - (14.3) Short-circuit across insulation consisting of lacquer, enamel or textile (see appended table) (see appended table) - (14.4) Short-circuit across electrolytic capacitors (see appended table) - (14.5) After the tests the insulation resistance with d.c. 500 V (MΩ) are 1 MΩ...: After the tests the accessible parts has not become live During the tests, a five-layer tissue paper, where the test specimen is wrapped, does not ignite Temperature declared thermally protected controlgear fulfil the requirements in Annex C 15 TRANSFORMER HEATING Windings of separating transformer in a SELVequivalent controlgear fulfil the requirements according to 7.1 and 11.2 of IEC Temperatures do not exceed the changed values of the values in column 2 of Table 3 of IEC 60065, in respect to relevant ambient temperature at t c, under normal operation 15.2 Temperatures do not exceed the changed values of the values in column 3 of Table 3 of IEC 60065, in respect to relevant ambient temperature at t c, under abnormal conditions of Cl. 16 and fault conditions of Cl. 14 Ambient temperature at t c...: 16 ABNORMAL CONDITIONS Safety not impaired when the controlgear is operated at any voltage between 90% and 110% of rated voltage 16.1 Control gear which are of the constant voltage output type: a) No LED module inserted b) Double LED modules or equivalent load connected to the output terminals c) Output terminal short-circuited (20 cm and 200 cm or declared length)

34 age 34 of 51 EN During and at the end of the tests no defect impairing safety, nor any smoke or flammable gases produced 16.2 Control gear which are of the constant current output type: a) No LED module connected b) Double the LED modules or equivalent load connected in series to the output terminals c) Output terminal short-circuited (20 cm and 200 cm or declared length ) Maximum output voltage not exceeded During and at the end of the tests no defect impairing safety, nor any smoke or flammable gases produced 17 (15) CONSTRUCTION - (15.1) Wood, cotton, silk, paper and similar fibrous material not used as insulation - (15.2) rinted boards used as internal connections complies with clause 14 of IEC Socket-outlet in the output circuit does not accept plugs complying with IEC and IEC Not possible to engage plugs accepted by socketoutlet in the output circuit with socket-outlets complying with IEC and IEC (16) CREEAGE DISTANCES AND CLEARANCES Creepage distances and clearances according to Table 3 and 4, as appropriate rinted boards see clause 14 of IEC Insulating lining of metallic enclosures (see cl. 11 of EN ) 19 (17) SCREWS, CURRENT-CARRYING ARTS AND CONNECTIONS Screws, current-carrying parts and connections in compliance with IEC (clause numbers between parentheses refer to IEC ) (4.11) Electrical connections (4.11.1) Contact pressure (4.11.2) Screws: - self-tapping screws - thread-cutting screws

35 age 35 of 51 EN at least two self-tapping screws (4.11.3) Screw locking: - spring washer - rivets (4.11.4) Material of current-carrying parts (4.11.5) No contact to wood (4.12) Mechanical connections and glands (4.12.1) Mechanical stress Screws not made of soft metal Screws of insulating material Torque test: part; torque (Nm)... : Torque test: part; torque (Nm)... : Torque test: part; torque (Nm)... : (4.12.2) Screw diameter < 3 mm screwed into metal (4.12.3) Void (4.12.4) Locked connections (4.12.5) Screwed glands: force (N)... : 20 (18) RESISTANCE TO HEAT, FIRE AND TRACKING 20 (18.1) arts of insulating material retaining live parts in position, ball-pressure test: - part; test temperature ( C)... : CB; 125 C - part; test temperature ( C)... : 20 (18.2) rinted boards in accordance with IEC , (18.3) External parts of insulating material preventing electric shock glow-wire test 650 C 20 (18.4) arts of insulating material retaining live parts in position, needle-flame test 10 s: - flame extinguished within 30 s - no flaming drops igniting tissue paper 20 (18.5) Tracking test 21 (19) RESISTANCE TO CORROSION Rust protection: - test according of IEC

36 age 36 of 51 EN adequate varnish on the outer surface - (20) NO-LOAD OUTUT VOLTAGE No load output voltage not differ more than 10 % from rated voltage

37 age 37 of 51 EN TABLE: tests of fault conditions art Simulated fault Hazard C10 Short-circuited LED switched off, can be resumed to normal NO C9 Short-circuited Fuse operated NO C8 Short-circuited Fuse operated NO C3 Short-circuited Normal operation NO C4 Short-circuited Fuse operated NO RV1 Short-circuited Fuse operated NO

38 age 38 of 51 EN (16) TABLE: creepage distances and clearances Minimum distances for a.c. (50/60 Hz) sinusoidal voltages RMS working voltage (V) not exceeding minimum distances between live parts of different polarity. Specify the value measured. 2 minimum distances between live parts and accessible parts which are permanently fixed to the ballast, including screws or devices for fixing covers or fixing the ballast to its support. Specify the value measured. - required creepage distances (mm), insulation TI required creepage distances (mm), insulation TI < ,6 1,4 1, ,5 1,2 1,6 2, required clearances (mm) 0,2 1,4 1, ,5 3 minimum distances between live parts and a flat supporting surface or a loose metal cover, if any, if the construction does not ensure that the values under 2 above are maintained under the most unfavourable circumstances required clearances (mm) 2 3,2 3,6 4,8 6 8 Minimum distances for non-sinusoidal pulse voltages rated pulse voltage (peak kv) 2,0 2,5 3,0 4,0 5,0 6,0 8,0 required minimum distances, clearances (mm) 1,0 1, ,5 8 Specify the value measured rated pulse voltage (peak kv) required minimum distances, clearances (mm) Specify the value measured rated pulse voltage (peak kv) required minimum distances, clearances (mm) Specify the value measured

39 age 39 of 51 EN A ANNEX A (NORMATIVE), TEST TO ESTABLISH WHETHER A CONDUCTIVE ART IS A LIVE ART WHICH MAY CAUSE AN ELECTRIC SHOCK A.2 See clause 8 A.2 in this Test Report A.3 See clause 8 A.3 in this Test Report C ANNEX C ARTICULAR REQUIREMENTS FOR ELECTRONIC LAM CONTROLGEAR WITH MEANS OF ROTECTION AGAINST OVERHEATING C3 GENERAL REQUIREMENTS C3.1 Thermal protection means integral with the controlgear, protected against mechanical damage Renewable only by means of a tool If function depending on polarity, for cordconnected equipment protection means in both leads Thermal links comply with IEC Electrical controls comply with IEC C3.2 No risk of fire by breaking (clause C7) C5 CLASSIFICATION a) automatic resetting type b) manual resetting type c) non-renewable, non-resetting type d) renewable, non-resetting type e) other type of thermal protection; description... : C6 MARKING C6.1 Symbol for temperature declared thermally protected ballasts C6.2 Declaration of the type of protection provided C7 LIMITATION OF HEATING C7.1 reselection test Test sample placed for at least 12 h in an oven having temperature (tc - 5) K No operation of the protection device

40 age 40 of 51 EN C7.2 Functioning of protection means Normal operation of the sample in a test enclosure according to Annex D at an ambient temperature such that (t c +0; -5) C is obtained No operation of the protection device Introducing of the most onerous test condition determined during test of clause 14 Output of windings connected to the mains supply short-circuited, and other part of the controlgear operated under normal conditions Increasing of the current through the windings continuously until operation of the protection means Continuous measuring of the highest surface temperature Controlgear according to C5 a) or C5 e) operated until stable conditions are achieved Automatic-resetting thermal protectors working 3 times Controlgear according to C5 b) working 6 times Controlgear according to C5 c) and C5) d) working once Highest temperature does not exceed the marked value Any overshoot of 10% over the marked value within 15 min D ANNEX D REQUIREMENTS FOR CARRY OUT THE HEATING TESTS OF THERMALLY ROTECTED LAM CONTROLGEAR Tests in C7 performed in accordance with Annex D, if applicable E ANNEX E USE OF CONSTANT S OTHER THAN 4500 IN t w TESTS E1 Constant S claimed Claimed test method E2 rocedure A Adequate data provided by the manufacturer The inverse of the slope is greater than or equal to the claimed value of S

41 age 41 of 51 EN Compliance with the failure criteria for procedure B E3 rocedure B Claimed value of T 1 Claimed value of T 2 Endurance test carried out at: T 1 (7 samples) T 2 (7 samples) Duration of test calculated from equation (2) T 1 T 2 During the test: - No open circuit - No breakdown insulation The claimed constant S is deemed to be verified F ANNEX F - DRAUGHT-ROOF ENCLOSURE Draught-proof enclosure in accordance with the description Dimensions of the enclosure Other design; description H ANNEX H - TESTS All tests performed in accordance with the advise given in Annex H, if applicable I ANNEX I - ARTICULAR ADDITIONAL REQUIREMENTS FOR INDEENDENT SELV D.C. OR A.C. SULIED ELECTRONIC CONTROLGEAR FOR LED MODULES I.3 Classification I.3.1 Class I Yes No Class II Yes No I.3.2 a) non-inherently short circuit proof controlgear Yes No b) non-inherently open circuit proof controlgear Yes No c) inherently short circuit proof controlgear Yes No

42 age 42 of 51 EN d) inherently open circuit proof controlgear Yes No e) fail safe controlgear Yes No f) non-short-circuit proof controlgear Yes No g) non-open-circuit proof controlgear Yes No I.4 Marking Adequate symbols are used I.5 rotection against electric shock I.5.1 No connection between output winding and body I.5.2 I I No connection between output winding and protective earthing circuit Input and output circuits electrically separated from each other Insulation between input and output winding of the HF-transformer consists of double or reinforced insulation Class II: insulation between input/output and body consists of double or reinforced insulation Class I: insulation between input and body consists of basic and between output and body supplementary insulation Insulation between input and output winding via the core consists of double or reinforced insulation Insulation between cord and windings of the HFtransformer consists of basic insulation I Serrated tape, additional layer I Class I controlgear for fixed connection provided with basic insulation plus protective screening comply with the following conditions: a) Insulation between the input winding and the protective screen complies with the requirements for basic insulation b) Insulation between the protective screen and the output winding complies with the requirements for basic insulation c) Metal screen consists of a metal foil or of a wire wound screen d) Metal screen so arranged that both edges cannot simultaneously touch a magnetic core

43 age 43 of 51 EN I I.5.3 e) Metal screen and its lead-out wire have a crosssection sufficient to ensure that an overload device will open the circuit before the screen is destroyed f) Lead-out wire sufficiently fixed to the metal screen Last turn of each winding of the transformer retained by positive means Impregnated winding Winding held together by means of insulating material Components bridging between input and output circuit I Used capacitors and resistors comply with 8.2 I Used opto-couplers I.6 Heating I.6.1 No excessive temperatures in normal use Used material classified as Class Stated value of t a I.6.2 Upri: 1.06 time supply rated voltage Determined temperature rises in windings: - rimary: K - Limit max: K - Secondary: K - Limit max: K After the test: - no connections have worked loose - no reduction of creepage distances and clearances - no flow of sealing compound - no operation of protecting devices - electric strength test between input and output windings I.6.3 Cycling test (10 cycles): I heat run at K I moisture treatment 48 h I vibration test 1 h; 1,5 g I After the tests:

44 age 44 of 51 EN insulation resistance - dielectric strength test at 35 % of specified value; test voltage V - Current or the ohmic component does not deviates by more than 30 % I.7 Short-circuit and overload protection I.7.1 Upri: 1.06 times rated voltage or 0.94 and 1.06 times rated supply voltage - used voltage V I.7.2 I.7.3 I.7.4 Determined temperature rise in windings and on other parts: - test according to Clause - rimary winding K - Limit max K - Secondary winding K - Limit max K - External enclosure K - Limit max 80 K - Rubber insulation of wiring K - Limit max 60 K - VC insulation of wiring K - Limit max 60 K - Supports K - Limit max 80 K I.7.5 Fail-safe convertors I Upri: 1.06 times rated supply voltage...v: - Isec: 1.5 times rated output current...a: - time until steady-state conditions t1 (h)... : - time until failure t2 (h): < t1; < 5 h... : I During the test: - no flames, molten material, etc. - temperature rise of enclosure < 150 K - temperature rise of plywood support < 100 K After the test:

45 age 45 of 51 EN electric strength (test voltage; 35 % of specified value); no flashover or breakdown for primary-tosecondary and for primary-to-body - live parts not accessible by test finger through holes of enclosure I.8 Insulation resistance and electric strength I.8.1 Conditioned 48 h between 91 % and 95 % I.8.2 Adequate insulation (500 V d.c. for 1 min) between: Live parts and the body -for basic insulation not less than 2 MΩ...: Live parts and the body -for reinforced insulation not less than 4 MΩ...: Input- and output circuits not less than 5 MΩ...: Metal parts of class II controlgear which are separated from live parts by basic insulation only and the body not less than 5 MΩ...: Metal foil in contact with the inner and outer surfaces of enclosures of insulating material not less than 2 MΩ...: I.8.3 Electric strength test: 1) Between live parts of input circuits and live parts of output circuits...: 2) Over basic or supplementary insulation between: a) live parts which are or may become of different polarity...: b) live parts and body if intended to be connected to protective earth...: c) accessible metal parts and a metal rod of the same diameter as the flexible cable or cord...: d) live parts and an intermediate metal part...: e) intermediate metal parts and the body...: 3) Over reinforced insulation between the body and live parts...: No flashover or breakdown occurred I.9 Construction I.9.1 Comply with all requirements I.9.2 The distance between input and output terminals shall not be less than 25 mm...: I.10 Components I.10.1 I.10.2 Socket-outlets in the output circuit does not accept plugs complying with IEC and IEC Self-resetting protective devices shall not be used unless it is certain that there will be no hazards

46 age 46 of 51 EN Compliance is checked by connecting the controlgear for 48 h at 1.06 times the rated voltage with the output short-circuited I.11 Creepage distances and clearances 1. Insulation between input and output circuits: a) measured values > specified values (mm)...: b) measured values > specified values (mm)...: c) measured values > specified values (mm)...: 2. Insulation between adjacent input circuits: measured values > specified values (mm)...: 2. Insulation between adjacent output circuits: measured values > specified values (mm)...: 3. Insulation between terminals for external connection: a) measured values > specified values (mm)...: b) measured values > specified values (mm)...: c) measured values > specified values (mm)...: 4. Basic or supplementary insulation: a) measured values > specified values (mm)...: b) measured values > specified values (mm)...: c) measured values > specified values (mm)...: 5. Reinforced insulation: measured values > specified values (mm)...: 6. Distande through insulation: a) measured values > specified values (mm)...: b) measured values > specified values (mm)...: c) measured values > specified values (mm)...: d) measured values > specified values (mm)...:

47 age 47 of 51 Sample hoto Outlook - T8-150EU Lamp cap

48 age 48 of 51 Sample hoto Construction Construction

49 age 49 of 51 Sample hoto Construction Construction

50 age 50 of 51 Sample hoto Construction LED

51 age 51 of 51 Sample hoto LED LED