TEST REPORT IEC Luminaires Part 2: Particular requirements: Section Two Recessed luminaires

Transcription

1 Test Report issued under the responsibility of: TEST REORT Luminaires art 2: articular requirements: Section Two Recessed luminaires Report Reference No...: A Date of issue...: Total number of pages pages CB Testing Laboratory...: Address...: Applicant s name...: Address...: DEKRA Testing and Certification China Ltd. 10F, #250 Jiangchangsan Road, Building 16, Headquarter Economy ark Shibei Hi-Tech ark, Zhabei District, Shanghai, , China hilips Lighting Luminaires (Shanghai) Co., Ltd. No. 2688, Hu Yi Road, Jiading, Shanghai, ,.R.China Test specification: Standard...: Test procedure...: Non-standard test method..: :1996+A1:1997 used in conjunction with IEC :2008 CB Test Report Form No...: Test Report Form(s) Originator...: IEC60598_2_2A Master TRF...: Intertek Semko AB Copyright 2008 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. If this Test Report Form is used by non-iecee members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.

2 age 2 of 36 Report No.: A Test item description...: Trade Mark...: Ceiling Light HILIS Manufacturer...: Model/Type reference...: hilips Lighting Luminaires (Shanghai) Co., Ltd. No. 2688, Hu Yi Road, Jiading, Shanghai, ,.R.China RC600B/LED31S/W60L60; RC600B/LED40S/W60L60; RC600B/LED31S/W60L60/AIR; RC600B/LED40S/W60L60/AIR; RC600B/LED31S/W30L120; RC600B/LED40S/W30L120; RC600B/LED31S/W30L120/AIR; RC600B/LED40S/W30L120/AIR; RC600B/LED31S/ACL/W60L60; RC600B/LED40S/ACL/W60L60; RC600B/LED31S/ACL/W60L60/AIR;RC600B/LED40S/ACL/W60L6 0/AIR; RC600B/LED31S/ACL/W30L120; RC600B/LED40S/ACL/W30L120;RC600B/LED31S/ACL/W30L120/ AIR; RC600B/LED40S/ACL/W30L120/AIR Ratings...: V~; 50/60 Hz; I20; Class l; RC600B/LED31S/W60L60: 40 W RC600B/LED40S/W60L60: 55 W RC600B/LED31S/W60L60/AIR: 40 W RC600B/LED40S/W60L60/AIR: 55 W RC600B/LED31S/W30L120: 40 W RC600B/LED40S/W30L120: 55 W RC600B/LED31S/W30L120/AIR: 40 W RC600B/LED40S/W30L120/AIR: 55 W RC600B/LED31S/ACL/W60L60: 40 W RC600B/LED40S/ACL/W60L60: 55 W RC600B/LED31S/ACL/W60L60/AIR: 40 W RC600B/LED40S/ACL/W60L60/AIR: 55 W RC600B/LED31S/ACL/W30L120: 40 W RC600B/LED40S/ACL/W30L120: 55 W RC600B/LED31S/ACL/W30L120/AIR: 40 W RC600B/LED40S/ACL/W30L120/AIR: 55 W

3 age 3 of 36 Report No.: A Testing procedure and testing location: CB Testing Laboratory: Testing location/ address...: Associated CB Laboratory: Testing location/ address...: Tested by (name + signature)...: DEKRA Testing and Certification China Ltd. 10F, #250 Jiangchangsan Road, Building 16, Headquarter Economy ark Shibei Hi-Tech ark, Zhabei District, Shanghai, , China Vicky Zhang Approved by (+ signature)...: Lix Li Testing procedure: TM Tested by (name + signature)...: Approved by (+ signature)...: Testing location/ address...: Testing procedure: WMT Tested by (name + signature)...: Witnessed by (+ signature)...: Approved by (+ signature)...: Testing location/ address...: Testing procedure: SMT Tested by (name + signature)...: Approved by (+ signature)...: Supervised by (+ signature)...: Testing location/ address...: Testing procedure: RMT Tested by (name + signature)...: Approved by (+ signature)...: Supervised by (+ signature)...: Testing location/ address...:

4 Summary of testing: age 4 of 36 Report No.: A Tests performed (name of test and test clause): Testing location: All applicable tests have been done in CBTL. DEKRA Testing and Certification China Ltd. 10F, #250 Jiangchangsan Road, Building 16, Headquarter Economy ark Shibei Hi-Tech ark, Zhabei District, Shanghai, , China Summary of compliance with National Differences: ass Copy of marking plate

5 age 5 of 36 Report No.: A Test item particulars... : Classification of installation and use... : Ceiling Light Class I; normal use; I20 Supply Connection... : Screwless terminal block... : Type X attachment... : - ossible test case verdicts: - test case does not apply to the test object... : - test object does meet the requirement... : (ass) - test object does not meet the requirement... : F (Fail) Testing... : - Date of receipt of test item... : Date (s) of performance of tests... : to General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Throughout this report a comma is used as the decimal separator. Clause numbers between brackets refer to clauses in IEC Although the followings are not listed in test report, the following standards have also been taken into account: - EN :2008+A11: EN : IEC : EN : IEC/TR :2009 Factory: Shanghai FUFA Metals Co., LTD. No.2770 Bao An RD. Malu Town Jiading Disrict Shanghai China This report should be read in conjunction with the attached pages concerned with the European group differences and national differences of the standards EN :1997 with the reference number of B. (2 pages)

6 age 6 of 36 Report No.: A General product information: These are 16 models of ceiling Light with LED light in this report; these products can be distinguished as two series according to difference of with or without dali controller. For the model name, 31S means its lumen output is 3100 lm, 40S means its lumen output is 4000 lm; ACL means this model has actilume sensor; W60L60 means its dimension is 597 x 597 mm W30L120 means its dimension is 297 x 1197 mm AIR means this model have air-condition hole All the models have similar electrical construction and mechanical construction, just with difference listed above, therefore model RC600B/LED40S/W60L60 which has the highest lumen output and without aircondition hole were selected to perform the type test, other model RC600B/LED40S/ACL/W60L60/AIR, RC600B/LED31S/W60L60, RC600B/LED40S/W30L120/AIR and RC600B/LED31S/W30L120 were selected to perform endurance test and insulation resistance and electronic strength test, and additional construction test was performed on model RC600B/LED31S/W30L120 The product is classified as Exempt group according to IEC :2006 and IEC/TR :2009.The test result was laid in test report A and B.

7 age 7 of 36 Report No.: A 2.2 (0) GENERAL TEST REQUIREMENTS 2.2 (0.1) Information for luminaire design considered Yes No 2.2 (0.3) More sections applicable...: Yes No 2.4 (2) CLASSIFICATION 2.4 (2.2) Type of protection (Class 0 excluded)... : Class I 2.4 (2.3) Degree of protection (Requirement: Ordinary)... : I (2.4) Luminaire suitable for direct mounting on normally flammable surfaces... : Luminaire not suitable for direct mounting on normally flammable surfaces... : Luminaire suitable to be covered by insulating material... : Yes No Yes No Yes No 2.4 (2.5) Luminaire for normal use... : Yes No Luminaire for rough service... : Yes No 2.5 (3) MARKING 2.5 (3.2) Mandatory markings osition of the marking Format of symbols/text 2.5 (3.3) Additional information Language of instructions 2.5 (3.3.1) Combination luminaires 2.5 (3.3.2) Nominal frequency in Hz 2.5 (3.3.3) Operating temperature 2.5 (3.3.4) Symbol or warning notice 2.5 (3.3.5) Wiring diagram 2.5 (3.3.6) Special conditions 2.5 (3.3.7) Metal halide lamp luminaire warning 2.5 (3.3.8) Limitation for semi-luminaires 2.5 (3.3.9) ower factor and supply current 2.5 (3.3.10) Suitability for use indoors 2.5 (3.3.11) Luminaires with remote control 2.5 (3.3.12) Clip-mounted luminaire warning

8 age 8 of 36 Report No.: A 2.5 (3.3.13) Specifications of protective shields 2.5 (3.3.14) Symbol for nature of supply ac 2.5 (3.3.15) Rated current of socket outlet 2.5 (3.3.16) Rough service luminaire 2.5 (3.3.17) Mounting instruction for type Y, type Z and some type X attachments 2.5 (3.3.18) Non-ordinary luminaires with VC cable 2.5 (3.3.19) rotective conductor current in instruction if applicable 2.5 (3.3.20) rovided with information if not intended to be mounted within arms reach 2.5 (3.4) Test with water Test with hexane Legible after test Label attached (-) Warning notice, if not suitable for insulating ceiling 2.6 (4) CONSTRUCTION 2.6 (4.2) Components replaceable without difficulty 2.6 (4.3) Wireways smooth and free from sharp edges 2.6 (4.4) Lampholders 2.6 (4.4.1) Integral lampholder 2.6 (4.4.2) Wiring connection 2.6 (4.4.3) Lampholder for end-to-end mounting 2.6 (4.4.4) ositioning - pressure test (N)... : After test the lampholder comply with relevant standard sheets and show no damage After test on single-capped lampholder the lampholder have not moved from its position and show no permanent deformation - bending test (N)... : After test the lampholder have not moved from its position and show no permanent deformation 2.6 (4.4.5) eak pulse voltage 2.6 (4.4.6) Centre contact

9 age 9 of 36 Report No.: A 2.6 (4.4.7) arts in rough service luminaires resistant to tracking 2.6 (4.4.8) Lamp connectors 2.6 (4.4.9) Caps and bases correctly used 2.6 (4.5) Starter holders Starter holder in luminaires other than class II Starter holder class II construction 2.6 (4.6) Terminal blocks Tails Unsecured blocks 2.6 (4.7) Terminals and supply connections 2.6 (4.7.1) Contact to metal parts 2.6 (4.7.2) Test 8 mm live conductor Test 8 mm earth conductor 2.6 (4.7.3) Terminals for supply conductors 2.6 ( ) Welded connections: - stranded or solid conductor - spot welding - welding between wires - Type Z attachment - mechanical test according to electrical test according to heat test according to and (4.7.4) Terminals other than supply connection 2.6 (4.7.5) Heat-resistant wiring/sleeves 2.6 (4.7.6) Multi-pole plug - test at 30 N 2.6 (4.8) Switches: - adequate rating - adequate fixing - polarized supply - compliance with for electronic switches 2.6 (4.9) Insulating lining and sleeves 2.6 (4.9.1) Retainement Method of fixing... :

10 age 10 of 36 Report No.: A 2.6 (4.9.2) Insulated linings and sleeves Resistant to a temperature > 20 C to the wire temperature or a) & c) Insulation resistance and electric strength b) Ageing test. Temperature ( C)... : 2.6 (4.10) Insulation of Class II luminaires 2.6 (4.10.1) No contact, mounting surface accessible metal parts wiring of basic insulation Safe installation fixed luminaires Capacitors and switches Interference suppression capacitors according to IEC (4.10.2) Assembly gaps: - not coincidental - no straight access with test probe 2.6 (4.10.3) Retainment of insulation: - fixed - unable to be replaced; luminaire inoperative - sleeves retained in position - lining in lampholder 2.6 (4.11) Electrical connections 2.6 (4.11.1) Contact pressure 2.6 (4.11.2) Screws: - self-tapping screws - thread-cutting screws 2.6 (4.11.3) Screw locking: - spring washer - rivets 2.6 (4.11.4) Material of current-carrying parts 2.6 (4.11.5) No contact to wood or mounting surface 2.6 (4.11.6) Electro-mechanical contact systems 2.6 (4.12) Mechanical connections and glands 2.6 (4.12.1) Screws not made of soft metal Screws of insulating material Torque test: torque (Nm); part... : Screw fixing enclosure, driver and cord anchorage; 1,2 Nm

11 age 11 of 36 Report No.: A Torque test: torque (Nm); part... : Screw fixing reflector; 0,6 Nm Torque test: torque (Nm); part... : 2.6 (4.12.2) Screws with diameter < 3 mm screwed into metal 2.6 (4.12.4) Locked connections: - fixed arms; torque (Nm)... : - lampholder; torque (Nm)... : - push-button switches; torque 0,8 Nm... : 2.6 (4.12.5) Screwed glands; force (Nm)... : 2.6 (4.13) Mechanical strength 2.6 (4.13.1) Impact tests: - fragile parts; energy (Nm)... : - other parts; energy (Nm)... : 0,35 Nm for enclosure, lens and reflector 1) live parts 2) linings 3) protection 4) covers 2.6 (4.13.3) Straight test finger 2.6 (4.13.4) Rough service luminaires - I54 or higher a) fixed b) hand-held c) delivered with a stand d) for temporary installations and suitable for mounting on a stand 2.6 (4.13.6) Tumbling barrel 2.6 (4.14) Suspensions and adjusting devices 2.6 (4.14.1) Mechanical load: A) four times the weight B) torque 2,5 Nm C) bracket arm; bending moment (Nm)... : D) load track-mounted luminaires E) clip-mounted luminaires, glass-shelve. Thickness (mm)... : Metal rod. diameter (mm)... :

12 age 12 of 36 Report No.: A Fixed luminaire or independent control gear without fixing devices 2.6 (4.14.2) Load to flexible cables Mass (kg)... : Stress in conductors (N/mm²)... : Mass (kg) of semi-luminaire... : Bending moment (Nm) of semi-luminaire... : 2.6 (4.14.3) Adjusting devices: - flexing test; number of cycles... : - strands broken - electric strength test afterwards 2.6 (4.14.4) Telescopic tubes: cords not fixed to tube; no strain on conductors 2.6 (4.14.5) Guide pulleys 2.6 (4.14.6) Strain on socket-outlets 2.6 (4.15) Flammable materials: - glow-wire test 650 C - spacing 30 mm - screen withstanding test of screen dimensions - no fiercely burning material - thermal protection - electronic circuits exempted 2.6 (4.15.2) Luminaires made of thermoplastic material with lamp control gear a) construction b) temperature sensing control c) surface temperature 2.6 (4.16) Luminaires for mounting on normally flammable surfaces No lamp control gear (compliance with Section 12) 2.6 (4.16.1) Lamp control gear spacing: - spacing 35 mm - spacing 10 mm 2.6 (4.16.2) Thermal protection: - in lamp control gear - external

13 age 13 of 36 Report No.: A - fixed position - temperature marked lamp control gear 2.6 (4.16.3) Design to satisfy the test of 12.6 (see 12.6) 2.6 (4.17) Drain holes Clearance at least 5 mm 2.6 (4.18) Resistance to corrosion: 2.6 (4.18.1) - rust-resistance 2.6 (4.18.2) - season cracking in copper 2.6 (4.18.3) - corrosion of aluminium 2.6 (4.19) Ignitors compatible with ballast 2.6 (4.20) Rough service vibration 2.6 (4.21) rotective shield: 2.6 (4.21.1) Shield fitted Shield of glass if tungsten halogen lamps 2.6 (4.21.2) articles from a shattering lamp not impair safety 2.6 (4.21.3) No direct path 2.6 (4.21.4) Impact test on shield Glow-wire test on lamp compartment 2.6 (4.22) Attachments to lamps 2.6 (4.23) Semi-luminaires comply Class II 2.6 (4.24) UV radiation for tungsten halogen lamps and metal halide lamps (Annex ) 2.6 (4.25) No sharp point or edges 2.6 (4.26) Short-circuit protection: 2.6 (4.26.1) Uninsulated accessible SELV parts 2.6 (4.26.2) Short-circuit test 2.6 (4.26.3) Test chain according to Figure (11) CREEAGE DISTANCES AND CLEARANCES Working voltage (V)... : V~ for driver input 275 Vdc for driver output Voltage form Sinusoidal Non-sinusoidal TI < 600 > 600

14 age 14 of 36 Report No.: A Impulse withstand category (Normal category II) (Category III Annex U) Category II Category III Rated pulse voltage (kv)... : - (1) Current-carrying parts of different polarity: cr (mm); cl (mm)... : (2) Current-carrying parts and accessible parts: cr (mm); cl (mm)... : (3) arts becoming live due to breakdown of basic insulation and metal parts: cr (mm); cl (mm)... : (4) Outer surface of cable where it is clamped and metal parts: cr (mm); cl (mm)... : Driver separately approved For input of LED module. Cl = 3,0 mm > 1,68 mm Cr = 3,0 mm > 2,75 mm Cl = 3,1 mm > 1,68 mm Cr = 3,1 mm > 2,75 mm (5) Not used (6) Current-carrying parts and supporting surface: cr (mm); cl (mm)... : Cl = 3,1 mm > 1,68 mm Cr = 3,1 mm > 2,75 mm 2.8 (7) ROVISION FOR EARTHING 2.8 ( ) Accessible metal parts Metal parts in contact with supporting surface Resistance < 0,5 Ω 0,1 Ω 2.8 ( ) Self-tapping screws used Thread-forming screws Thread-forming screw used in a grove Earth makes contact first Earth continuity in joints etc. 2.8 (7.2.4) Locking of clamping means Compliance with Terminal blocks with integrated screwless earthing contacts tested according Annex V 2.8 (7.2.5) Earth terminal integral part of connector socket 2.8 (7.2.6) Earth terminal adjacent to mains terminals 2.8 (7.2.7) Electrolytic corrosion of the earth terminal 2.8 (7.2.8) Material of earth terminal Contact surface bare metal

15 age 15 of 36 Report No.: A 2.8 (7.2.10) Class II luminaire for looping-in Double or reinforced insulation to functional earth 2.8 (7.2.11) Earthing core coloured green-yellow Length of earth conductor 2.9 (14) SCREW TERMINALS Separately approved; component list (see Annex 1) art of the luminaire (see Annex 3) 2.9 (15) SCREWLESS TERMINALS AND ELECTRICAL CONNECTIONS Separately approved; component list (see Annex 1) art of the luminaire (see Annex 4) 2.10 (5) EXTERNAL AND INTERNAL WIRING 2.10 (5.2) Supply connection and external wiring 2.10 (5.2.1) Means of connection... : Screwless terminal block 2.10 (5.2.2) Type of cable... : Nominal cross-sectional area (mm²)... : 3 x 1,0 1,5 mm 2 Cables equal to IEC or IEC (5.2.3) Type of attachment, X, Y or Z Type X 2.10 (5.2.5) Type Z not connected to screws 2.10 (5.2.6) Cable entries: - suitable for introduction - adequate degree of protection 2.10 (5.2.7) Cable entries through rigid material have rounded edges 2.10 (5.2.8) Insulating bushings: - suitably fixed - material in bushings - material not likely to deteriorate - tubes or guards made of insulating material 2.10 (5.2.9) Locking of screwed bushings 2.10 (5.2.10) Cord anchorage: - covering protected from abrasion - clear how to be effective

16 age 16 of 36 Report No.: A 2.10 ( ) 2.10 ( ) 2.10 ( ) - no mechanical or thermal stress - no tying of cables into knots etc. - insulating material or lining Cord anchorage for type X attachment: a) at least one part fixed b) types of cable c) no damaging of the cable d) whole cable can be mounted e) no touching of clamping screws f) metal screw not directly on cable g) replacement without special tool Glands not used as anchorage Labyrinth type anchorages Adequate cord anchorage for type Y and type Z attachment Tests: - impossible to push cable; unsafe - pull test: 25 times; pull (N)... : 60 N for 3 x 1,0 mm 2 80 N for 3 x 1,5 mm 2 - torque test: torque (Nm)... : 0,25 Nm for 3 x 1,0 mm 2 0,35 Nm for 3 x 1,5 mm 2 - displacement 2 mm - no movement of conductors - no damage of cable or cord 2.10 (5.2.11) External wiring passing into luminaire 2.10 (5.2.12) Looping-in terminals 2.10 (5.2.13) Wire ends not tinned Wire ends tinned: no cold flow 2.10 (5.2.14) Mains plug same protection Class III luminaire plug 2.10 (5.2.16) Appliance inlets (IEC 60320) Appliance couplers of class II type 2.10 (5.2.17) No standardized interconnecting cables properly assembled

17 age 17 of 36 Report No.: A 2.10 (5.2.18) Used plug in accordance with - IEC other standard 2.10 (5.3) Internal wiring 2.10 (5.3.1) Internal wiring of suitable size and type Through wiring - not delivered/ mounting instruction - factory assembled - socket outlet loaded (A)... : - temperatures... : (see Annex 2) Green-yellow for earth only 2.10 ( ) Internal wiring connected directly to fixed wiring Cross-sectional area (mm²)... : 0,5-1,0 mm 2 for other internal wiring Insulation thickness Extra insulation added where necessary 2.10 ( ) Internal wiring connected to fixed wiring via internal current-limiting device Adequate cross-sectional area and insulation thickness 24 AWG for wiring connecting to the connector in the CB 2.10 ( ) Double or reinforced insulation for class II 2.10 ( ) Conductors without insulation 2.10 ( ) SELV current-carrying parts 2.10 ( ) Insulation thickness other than VC or rubber 2.10 (5.3.2) Sharp edges etc. No moving parts of switches etc. Joints, raising/lowering devices Telescopic tubes etc. No twisting over (5.3.3) Insulating bushings: - suitable fixed - material in bushings - material not likely to deteriorate - cables with protective sheath 2.10 (5.3.4) Joints and junctions effectively insulated 2.10 (5.3.5) Strain on internal wiring

18 age 18 of 36 Report No.: A 2.10 (5.3.6) Wire carriers 2.10 (5.3.7) Wire ends not tinned Wire ends tinned: no cold flow 2.11 (8) ROTECTION AGAINST ELECTRIC SHOCK 2.11 (8.2.1) Live parts not accessible with standard test finger Basic insulated parts not used on the outer surface without appropriate protection Basic insulated parts not accessible with standard test finger on portable and adjustable luminaires Basic insulated parts not accessible with Ø 50 mm probe from outside, within arms reach, on wall-mounted luminaires Lamp and starterholders in portable and adjustable luminaires comply with double or reinforced insulation requirements Basic insulation only accessible under lamp or starter replacement rotection in any position Double-ended tungsten filament lamp Insulation lacquer not reliable Double-ended high pressure discharge lamp Relevant warning according to fitted to the luminaire 2.11 (8.2.2) ortable luminaire adjusted in most unfavourable position 2.11 (8.2.3.a) Class II luminaire: - basic insulated metal parts not accessible during starter or lamp replacement - basic insulation not accessible other than during starter or lamp replacement - glass protective shields not used as supplementary insulation 2.11 (8.2.3.b) BC lampholder of metal in class I luminaires shall be earthed 2.11 (8.2.3.c) Class III luminaires with exposed SELV parts: Ordinary luminaire: - touch current... : - no-load voltage... :

19 age 19 of 36 Report No.: A Other than ordinary luminaire: - nominal voltage... : 2.11 (8.2.4) ortable luminaire: - protection independent of supporting surface - terminal block completely covered 2.11 (8.2.5) Compliance with the standard test finger or relevant probe 2.11 (8.2.6) Covers reliably secured 2.11 (8.2.7) Discharging of capacitors 0,5 μf ortable plug connected luminaire with capacitor Other plug connected luminaire with capacitor Discharge device on or within capacitor Discharge device mounted separately 2.12 (12) ENDURANCE TEST AND THERMAL TEST 2.12 (12.3) Endurance test: - mounting-position... : Normal position - test temperature ( C)... : 35 C - total duration (h)... : 240 h - supply voltage: Un factor; calculated voltage (V): 264 V~ - lamp used... : As delivered 2.12 (12.3.2) After endurance test: - no part unserviceable - luminaire not unsafe - no damage to track system - marking legible - no cracks, deformation etc (12.4) Thermal test (normal operation) (see Annex 2) 2.12 (12.5) Thermal test (abnormal operation) (see Annex 2) 2.12 (12.6) Thermal test (failed lamp control gear condition): 2.12 (12.6.1) Through wiring or looping-in wiring loaded by a current of (A)... : - case of abnormal conditions... : - electronic lamp control gear - measured winding temperature ( C): at 1,1 Un. :

20 age 20 of 36 Report No.: A - measured mounting surface temperature ( C) at 1,1 Un... : - calculated mounting surface temperature ( C).. : - track-mounted luminaires 2.12 (12.6.2) Temperature sensing control - case of abnormal conditions... : - thermal link - manual reset cut-out - auto reset cut-out - measured mounting surface temperature ( C)... : - track-mounted luminaires 2.12 (12.7) Thermal test (failed lamp control gear in plastic luminaires): 2.12 (12.7.1) Luminaire without temperature sensing control 2.12 ( ) Luminaire with fluorescent lamp 70W Test method or Annex V... : Test according to : - case of abnormal conditions - Ballast failure at supply voltage (V)... : - Components retained in place after the test - Test with standard test finger after the test Test according to Annex V: - case of abnormal conditions 2.12 ( ) - measured winding temperature ( C): at 1,1 Un.. : - measured temperature of fixing point/exposed part ( C): at 1,1 Un... : - calculated temperature of fixing point/exposed part ( C)... : Ball-pressure test: - part tested; temperature ( C)... : - part tested; temperature ( C)... : Luminaire with discharge lamp, fluorescent lamp > 70W, transformer > 10 VA - case of abnormal conditions - measured winding temperature ( C): at 1,1 Un.. :

21 age 21 of 36 Report No.: A 2.12 ( ) - measured temperature of fixing point/exposed part ( C): at 1,1 Un... : - calculated temperature of fixing point/exposed part ( C)... : Ball-pressure test: - part tested; temperature ( C)... : - part tested; temperature ( C)... : Luminaire with short circuit proof transformers 10 VA - case of abnormal conditions - Components retained in place after the test - Test with standard test finger after the test 2.12 (12.7.2) Luminaire with temperature sensing control - thermal link Yes No - manual reset cut-out Yes No - auto reset cut-out Yes No - case of abnormal conditions - highest measured temperature of fixing point/exposed part ( C):... : Ball-pressure test: - part tested; temperature ( C)... : - part tested; temperature ( C)... : 2.13 (9) RESISTANCE TO DUST, SOLID OBJECTS AND MOISTURE 2.13 (9.2) Tests for ingress of dust, solid objects and moisture: - classification according to I... : I 20 - mounting position during test... : Recessed - fixing screws tightened; torque (Nm)... : - - tests according to clauses... : electric strength test afterwards a) no deposit in dust-proof luminaire b) no talcum in dust-tight luminaire c) no trace of water on current-carrying parts or SELV parts or where it could become a hazard d) i) For luminaires without drain holes no water entry

22 age 22 of 36 Report No.: A d) ii) For luminaires with drain holes no hazardous water entry e) no water in watertight luminaire f) no contact with live parts (I 2X) f) no entry into enclosure (I 3X and I 4X) f) no contact with live parts (I3X and I4X) g) no trace of water on part of lamp requiring protection from splashing water h) no damage of protective shield or glass envelope 2.13 (9.3) Humidity test 48 h 25 C; 93% 2.14 (10) INSULATION RESISTANCE AND ELECTRIC STRENGTH 2.14 (10.2.1) Insulation resistance test Cable or cord covered by metal foil or replaced by a metal rod of mm Ø... : Insulation resistance (MΩ) SELV: - between current-carrying parts of different polarity... : - between current-carrying parts and mounting surface... : - between current-carrying parts and metal parts of the luminaire... : Other than SELV: -- - between live parts of different polarity... : - between live parts and mounting surface... : 1000 MΩ - between live parts and metal parts... : 1000 MΩ - between live parts of different polarity through action of a switch... : 2.14 (10.2.2) Electric strength test Dummy lamp Luminaires with ignitors after 24 h test Luminaires with manual ignitors Test voltage (V): SELV:

23 age 23 of 36 Report No.: A - between current-carrying parts of different polarity... : - between current-carrying parts and mounting surface... : - between current-carrying parts and metal parts of the luminaire... : Other than SELV: - between live parts of different polarity... : - between live parts and mounting surface... : 1550 V - between live parts and metal parts... : 1550 V - between live parts of different polarity through action of a switch... : 2.14 (10.3) Touch current (ma)... : 0,2 ma <0,7 ma 2.15 (13) RESISTANCE TO HEAT, FIRE AND TRACKING 2.15 (13.2.1) Ball-pressure test: - part tested; temperature ( C)... : CB; 125 C - part tested; temperature ( C)... : 2.15 (13.3.1) Needle flame test (10 s): - part tested... : CB - part tested... : 2.15 (13.3.2) Glow-wire test (650 C): - part tested... : Lens - part tested... : Reflector - part tested... : CB - part tested... : Connector 2.15 (13.4.1) Tracking test: part tested... :

24 age 24 of 36 Report No.: A ANNEX 1: components object/part No. code manufacturer/ trademark type/model technical data standard mark(s) of conformity Supply terminal block B BJB A; 450 V; 1 2,5 IEC mm 2 1 VDE Terminal block B Yuyao City Lixun Electronics Co., Ltd. A-LX V; 16 A 0,75-2,5 mm 2 ; T110 IEC VDE Terminal block B Yuyao City Lixun Electronics Co., Ltd. A V; T110; 2,5 IEC mm 2 1 VDE LED Driver B hilips electronical Co.,Ltd Xitanium 75W A 200V TD 230V Vac; tc=75 ;Uout=275 Vdc EN ENEC05 LED C LG Innotek LEMWS59T80JZ00 2,9-3,4 V; ma IEC Tested in appliance CB C LG Innotek LARWT270RAAAA V-0 IEC Tested in appliance Internal wiring connecting to connector in CB C LTK Technologies Co., Ltd AWG (7/32AWG)TS*1C IEC Tested in appliance Internal wire C SHANGHAI ANDA WIRE & CABLE CO.,LTD IEC07(BV- 90) 300/500 V; 0,5-2,5 mm² IEC Tested in appliance Internal wire C Shanghai Sunqiao Electric Wire & Cable (Group) Co., Ltd IEC06 (RV) 300/500 V; 0,5-1,0 mm² IEC Tested in appliance Actilume sensor B hilips LRI 1653/01 Ta=0 55 EN ENEC05 Actilume controller B hilips LCC 1653/ V~ 50/60 Hz EN ENEC05 Connector C JST A-07V-S A66; UL94V-0 IEC Connector C MOLEX BT; UL94V-0 IEC Tested in appliance Tested in appliance The codes above have the following meaning: A - The component is replaceable with another one, also certified, with equivalent characteristics B - The component is replaceable if authorised by the test house C - Integrated component tested together with the appliance D - Alternative component

25 age 25 of 36 Report No.: A ANNEX 2: temperature measurements, thermal tests of Section 12 Type reference...: RC600B/LED40S/W60L60 Lamp used...: As delivered Lamp control gear used...: Xitanium 75W A 200V TD 230V Mounting position of luminaire...: Recessed Supply wattage (W)...: 54,8 W at 240 V Supply current (A)...: 0,235 A Calculated power factor...: 0,972 Table: measured temperatures corrected for ta = 25 C: - abnormal operating mode...: Short-circuit the output of LED driver, and the product was protected - test 1: rated voltage...: 240 V - test 2: 1,06 times rated voltage or 1,05 times rated wattage...: - test 3: Load on wiring to socket-outlet, 1,06 times voltage or 1,05 times wattage...: - test 4: 1,1 times rated voltage or 1,05 times rated wattage...: Through wiring or looping-in wiring loaded by a current of A during the test...: 254,4 V V - temperature ( C) of part Clause 12.4 normal Clause 12.5 abnormal test 1 test 2 test 3 limit test 4 limit Lens - 36, Reflector - 30, Internal wire connecting to driver Internal wire connecting to LED module - 33, , CB - 50, Connector - 35, Screwless terminal block - 30, Earthing wire - 31,

26 age 26 of 36 Report No.: A Cord anchorage - 29, Mounting surface - 38, tc 48, Enclosure of Actilumen controller - 34,

27 age 27 of 36 Report No.: A ANNEX 3: screw terminals (part of the luminaire) ANNEX 4: screwless terminals (part of the luminaire)

28 Annex user manual: age 28 of 36 Report No.: A

29 Annex user manual: age 29 of 36 Report No.: A

30 Annex pictures: age 30 of 36 Report No.: A Top view without air-condition hole for series RC600B/LEDXXS/(ACL)/W60L60 Top view with air-condition hole for series RC600B/LEDXXS/(ACL)/W60L60/AIR

31 Annex pictures (continued): age 31 of 36 Report No.: A Bottom view for series RC600B/LEDXXS/(ACL)/W60L60/(AIR) Side view for RC600B/LEDXXS/(ACL)/W60L60/(AIR)

32 Annex pictures (continued): age 32 of 36 Report No.: A Top view for series RC600B/LEDXXS/(ACL)/W30L120/(AIR) Bottom view for series RC600B/LEDXXS/(ACL)/W30L120/(AIR)

33 Annex pictures (continued): age 33 of 36 Report No.: A Sensor Back of the sensor

34 Annex pictures (continued): age 34 of 36 Report No.: A Earthing terminal Fixing rivets

35 Annex pictures (continued): age 35 of 36 Report No.: A Internal view for RC600B/LEDXXS/(ACL)/W60L60/(AIR) Internal view for RC600B/LEDXXS/(ACL)/W30L120/(AIR)

36 S Annex pictures (continued): age 36 of 36 Report No.: A Internal view for RC600B/LEDXXS/(ACL)/W30L120/(AIR) Sensor