TEST REPORT IEC Audio, video and similar electronic apparatus - Safety requirements

Transcription

1 Test Report issued under the responsibility of TEST REORT IEC Audio, video and similar electronic apparatus - Safety requirements Report Reference o.... : Date of issue... : Total number of pages... : 40 page and refer page 5 CB/CCA Testing Laboratory ame: emko Taiwan hone: (+ 886) Address... : Applicant s name... : Address... : 5 Fl., o. 409, Sec.2, Tiding Blvd., eihu, Taipei 114, Taiwan Eastern Frontier Co., Ltd. 13TH FL, BLK B, CHUG MEI CETRE, 15 HIG YI ST., KWU TOG, KOWLOO, HOG KOG Test specification: Standard... : IEC 60065:2001(7 th edition) + Amd 1:2005 E 60065: A1: 2006 Test procedure... : on-standard test method..: Test Report Form o.... : Test Report Form(s) Originator...: CB /A IEC60065_I Intertek Semko AB Master TRF...: Copyright 2008 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. If this Test Report Form is used by non-iecee members, the IECEE/IEC logo and the reference to the CB scheme procedure shall be removed. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an CB in accordance with IECEE 02. This Test Report, when bearing the emko name and logo is only valid when issued by a emko laboratory, or by a laboratory having special agreement with emko.

2 Test Report issued under the responsibility of Test item description... : Trade Mark... : Manufacturer... : Model/Type reference... : Ratings... : Switching power supply (direct plug-in adapter with interchangeable or fixed plug) 1) ; 2) Same as applicant EFS The dots.. definition: CE (European plug and United Kingdom plug), AU (Australia plug), J (fixed Japan plug), and A (Korea plug, China plug, Taiwan plug and Hong Kong plug I/: 0.68A V~ 50/60Hz DC-output: 1.39A 12.9V ortable apparatus Dimension: Max x 63.5 x 34 mm Mass: 140g This Test Report, when bearing the emko name and logo is only valid when issued by a emko laboratory, or by a laboratory having special agreement with emko.

3 - age 3 of 40 - Report o Testing procedure and testing location: CB Testing Laboratory: Testing location/ address... : Associated CB Test Laboratory: Testing location/ address... : emko Taiwan 5 Fl., o. 409, Sec.2, Tiding Blvd., eihu, Taipei 114, Taiwan Tested by (name + signature)... : Eric Chen Approved by (+ signature)... : Andy Lee Testing procedure: TM Tested by (name + signature)... : Approved by (+ signature)... : Testing location/ address... : Testing procedure: WMT Tested by (name + signature)... : Witnessed by (+ signature)... : Approved by (+ signature)... : Testing location/ address... : Testing procedure: SMT Tested by (name + signature)... : Approved by (+ signature)... : Supervised by (+ signature)... : Testing location/ address..: Testing procedure: RMT Tested by (name + signature)... : Approved by (+ signature)... : Supervised by (+ signature)... : Testing location/ address... : TRF o. IEC60065_I

4 - age 4 of 40 - Report o Summary of testing: Flammability category according to IEC60707: FV 0 is considered to be equal to flammability class V-0. FV 1 is considered to be equal to flammability class V-1. FV 2 is considered to be equal to flammability class V-2. Tests performed (name of test and test clause): 5 Marking and instructions 7 Heating under normal operating conditions 8 Constructional requirements with regard to the protection against electric shock 9 Electric shock hazard under normal operating conditions 10 Insulation requirements 11 Fault conditions 12 Mechanical strength 13 Clearances and creepage distances 14 Components 15 Terminals 17 Electrical connections and mechanical fixings 19 Stability and mechanical hazards 20 Resistance to fire Testing location: Refer page 2 Summary of compliance with ational Differences: All CEELEC countries and countries listed except Canada (CA) and United States of America (US) in CB Bulletin o. 112A, dated December 2006 as follows: Argentina (AR), Austria (AT), Australia (AU), Belgium (BE), Brazil (BR), Switzerland (CH), China (C), Serbia and Montenegro (CS), Czech Republic (CZ), Germany (DE), Denmark (DK), Finland (FI), France (FR), Greece (GR), United Kingdom (GB), Hungary (HU), Italy (IT), Kenya (KE), Republic of Korea (KR), Malaysia (MY), The etherlands (L), orway (O), oland (L), ortugal (T), Russian Federation (RU), Sweden (SE), Singapore (SG), Slovenia (SI), Slovakia (SK) and Ukraine (UA). Copy of marking plate: TRF o. IEC60065_I

5 - age 5 of 40 - Report o ame and address of production-sites (Factories): 1. EASTER FROTIER(SHEZHE)CO., LTD. Factory Bldg #A Hua Fa Road, Ind. Area Da Lang Village Long Han Shenzhen, China 2. EASTER FROTIER(SHEZHE)CO., LTD. Factory Bldg#A Hua Fa Road, Ind. Area Da Lang ST., Bao An, Shenzhen, China List of attachments: CB layout (2 pages), hotos (9 pages), Transformer specification (2 pages), European group differences with others contries difference (16 pages), Europe plug report (12 pages) TRF o. IEC60065_I

6 - age 6 of 40 - Report o Test item particulars... : Classification of installation and use... : I20 Supply connection... : luggable equipment type A... :... : ossible test case verdicts: - test case does not apply to the test object...: (/A) - test object does meet the requirement...: (ass) - test object does not meet the requirement...: F (Fail) Testing... : Date of receipt of test items...: March, 2009 Date(s) of performance of tests...: March, 2009 General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(see Enclosure #)" refers to additional information appended to the report. "(see appended table)" refers to a table appended to the report. Throughout this report, a point (comma) is used as the decimal separator. List of test equipment must be kept on file and available for review. General product information: The sample(s) tested complies with the requirements of IEC 60065: 2001+Amd 1/E 60065:2002+A1. Compliance with European Special ational Conditions, Annex ZB, and A Deviations, Annex ZC, is recorded at the end of this report. Additional information: 1. The equipment under tests is Class II switching type power adapter with interchangeable or fixed plug. 2. The unit provide with Korea plug, China plug, Europe plug, United Kingdom plug, Hong Kong plug, Australia plug, fixed Japan plug and Taiwan plug. Only the Europe plug has been evaluated and complies with IEC and E 50075, others plugs should be checked when marketed in relevant country. The whole unit (include interchangeable plug) have been evaluated additional plug tests as follow and compliance with standard of IEC and E50075: times tumbiling barrel test. 2. Torgue test. 3. Ball pressure test. 3. The United Kingdom plug has been tested BS part 1, 12.1, 12..2, 12.3, 12.9, 12.11, 12.12, and Load condition: Loaded to rating. Maximum recommended ambient (Tmra): 45 C TRF o. IEC60065_I

7 - age 7 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict 3 General requirements Safety class of the apparatus : Class II 4 General test conditions Ventilation instructions require the use of the test box ositioned according to users manual. 5 Marking and instructions Comprehensible and easily discernible...: ermanent durability against water and petroleum spirit..: 5.1 a) Identification, maker..: b) Model number or type reference..: c) Class II symbol if applicable..: d) ature of supply...: e) Rated supply voltage and symbol : On the outside of the enclosure. Tested with water / spirit. 1) ; 2) EFS Class II symbol (IEC 60417, symbol o. 5172) is applied. AC symbol ( ~ ) used V f) Mains frequency if safety dependant....: 50/60Hz g) Rated current or power consumption for apparatus supplied by supply apparatus for general use : Measured current or power consumption...: Deviation % (max 10%)...: h) ower consumption marking for apparatus other than single phase...: The apparatus is connection to an a.c. mains supply The apparatus is connection to an single phase a.c. mains supply i) Rated current or power consumption for apparatus intended for connection to an a.c. mains supply : 0.68A Measured current or power consumption.....: Considered, refer to appended table 7.1. TRF o. IEC60065_I

8 - age 8 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict Deviation % (max 10%)...: 5.2 Earth terminal..: Hazardous live terminals : The steady state input current of the apparatus measured at RATED SULY VOLTAGE not exceed the marked value by more than 10 % under ORMAL LOAD. Class II apparatus. o live parts accessible. Supply output terminals (other than mains)...: o socket outlet for providing power to other apparatus. 5.3 Use of triangle with exclamation mark.: The mark is shown on the electrical diagram above every safety critical components. 5.4 Instructions for use.: Refer to below a) Mains powered equipment not exposed to dripping or splashing. Warning concerning objects filled with liquid, etc..: b) Hazardous live terminals, instructions for wiring...: c) Instructions for replacing lithium battery..: d) Class I earth connection warning.: Instructions and markings shall be in a language acceptable for the country where the equipment is to be used. o live terminal. o battery. Class II apparatus. e) Instructions for multimedia system connection..: o direct connected to multimedia system. f) Special stability warning for attachment of the apparatus to the floor/wall : Direct plug-in apparatus. g) Warning: battery exposure to heat..: ot such equipment. h) Warning: protective film on CRT face.: ot such equipment Disconnect device: plug/coupler or all-pole mains switch location, accessibility and markings.: Instructions for permanently connected equipment...: Marking, signal lamps or similar for completely disconnection from the mains... : The plug will be acting as disconnect device. The apparatus is not for permanent connection. ot such equipment. TRF o. IEC60065_I

9 - age 9 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict 6 Hazardous radiations 6.1 Ionizing radiation < 36 pa/kg (0,5 mr/h).: Ionizing radiation under fault condition.: o radiation hazard. 6.2 Laser radiation, emission limits to IEC : Emission limits under fault conditions..: 7 Heating under normal operating conditions 7.1 Temperature rises not exceeding specified values; fuse links and other protective devices defeated...: o fuse links operate during normal operating operation. (see appended table 7.1) Temperature rise of accessible parts..: (see appended table 7.1) Temperature rise of parts providing electrical insulation.. : Temperature rise of parts acting as a support or as a mechanical barrier..: Temperature rise of windings : (see appended table 7.1) o such parts used. (see appended table 7.1) arts not subject to a limit under to (see appended table 7.1) 7.2 Softening temperature of insulating material supporting parts conductively connected to the mains carrying a current > 0,2 A at least 150 o C : 1. CB: Epoxy. 2. lug, see appended table For bobbin of transformer are phenolic. 8 Constructional requirements with regard to the protection against electric shock 8.1 Conductive parts covered by lacquer, paper, untreated textile oxide films and beads etc. considered to be bare : 8.2 o shock hazard when changing voltage setting device, fuse-links or handling drawers etc..: 8.3 Insulation of hazardous live parts not provided by hygroscopic material..: Considered. o voltage setting device is provided. o hygroscopic materials used. TRF o. IEC60065_I

10 - age 10 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict 8.4 o risk of electric shock from accessible parts or from parts rendered accessible following the removal of a cover which can be removed by hand..: 8.5 Class I equipment...: Basic insulation between hazardous live parts and earthed accessible parts : Resistors bridging basic insulation complying with 14.1 a)..: Capacitors bridging basic insulation complying with a)...: rotective earthing terminal...: 8.6 Class II equipment and Class II constructions within Class I equipment...: Double or reinforced insulation between hazardous live parts and accessible parts..: Components bridging double or reinforced insulation complying with 14.1 a) or : Basic insulation bridged by components complying with : Basic and supplementary insulation each being bridged by a capacitor complying with a) : Double or reinforced insulation being bridged with 2 capacitors in series complying with a).: Double or reinforced insulation being bridged with a single capacitor complying with b) : o risk of electric shock after enclosure removed. Class II apparatus. Refer to below. Double/Reinforced insulation complies with requirements specified in clause 10 and 13. 1) The apparatus have isolating transformer (T1) complies with clause ) Optocouplers (IC2) complies with o such capacitors. o such capacitors. o such capacitors. Y1 capacitor (CY1) is approved component which complied with IEC / This clause is void..: 8.8 Basic or supplementary insulation > 0,4 mm (mm)...: o such insulation used. TRF o. IEC60065_I

11 - age 11 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict TRF o. IEC60065_I Reinforced insulation > 0,4 mm (mm).: 1) Approved sources of optocouplers are used. All sources provided distance of at least 0.4mm. 2) Thickness of transformer bobbin is min. 0.5mm. Thin sheet insulation (excluding non-separable thin sheet insulation. See 8.22) : Basic or supplementary insulation, at least two layers, each meeting : Basic or supplementary insulation, three layers any two of which meet : Reinforced insulation, two layers each of which meet : Reinforced insulation, three layers any two which meet 10.3.: 8.9 Adequate insulation between internal hazardous live conductors and accessible parts..: 8.10 Adequate insulation between internal hazardous live parts and conductors connected to accessible parts : Double insulation between conductors connected to the mains and accessible parts....: Double insulation between internal hazardous live parts and conductors connected to accessible parts. : 8.11 Detaching of wires..: o undue reduction of creepages or clearance distances if wires become detached : Vibration test carried out : o used. o used. o used. o such insulation used. 3 layers tape on isolating transformer body (T1). Reinforced insulation. Single insulated but safely anchored. Refer below Double or reinforced insulation provided between conductors connected to the mains and accessible parts. Refer to below: o wire could be become detached This clause is void..: 8.13 Adequate fastening of windows, lenses, lamp covers etc. (pull test 20 for 10 s)...: o such parts used.

12 - age 12 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict 8.14 Adequate fastening of covers (push/pull test 50 for 10 s).. : 8.15 o risk of damage to the insulation of internal wiring due to hot parts or sharp edges : o such cover used. o risk of damage to insulation due to high temperature, sharp edges or pinches Only special supply equipment can be used...: o special supply apparatus used Insulated winding wire without additional interleaved insulation.. : Insulation on winding wires of T1 complies with IEC See list of critical components Endurance test as required by 8.17.: Test not required Disconnection from the mains See below Disconnect device...: The plug will be acting as disconnect device and compliance with All-pole switch or circuit breaker with >3mm contact separation : Mains switch O indication...: 8.20 Switch not fitted in the mains cord : 8.21 Bridging components comply with clause 14..: o such part used. o such device. o such device. o bridging components are used for bridging gaps of switch conductively connected to the mains on-separable thin sheet material...: o such part used. 9 Electric shock hazard under normal operating conditions 9.1 Testing on the outside See below: For voltages >1000 V ac or >1500 V dc complies with clause for basic insulation.: o such high voltage provided a) Open circuit voltages.: For output connector: Max. 13.2Vdc. b) Touch current measured from terminal devices using the network in annex D : c) Discharge not exceeding 45 μc...: Measured location: Main poles and output connector. (see appended table 9.1.1) The discharge didn t exceed 45μC. TRF o. IEC60065_I

13 - age 13 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict d) Energy of discharge not exceeding 350 mj...: Test with test finger and test probe...: o hazardous live shafts of knobs, handles or levers : Ventilation holes and other holes tested by means of 4 mm x 100 mm test pin : Terminal devices tested with 1 mm x 20 mm test pin (10 ); test probe D of IEC : Terminal devices tested with 1 mm x 100 mm straight wire (1 ); test probe D of IEC : re-set controls tested with 2.5 mm x 100 mm test pin (10 ); test probe C of IEC : o shock hazard due to stored charge on withdrawal of the mains plug; voltage (V) after 2 s : If C is not greater than 0,1 μf no test needed : o part with stored voltages exceeding 15kV. o access to hazardous live parts. o live shafts, handles or levers. o openings. o terminal. o pre-set controls used. o X capacitor provided. The normal capacitance across the mains poles does not exceed 0.1μF Resistance to external forces o damage to the enclosure. a) Test probe 11 of IEC for 10 s (50 )...: Test with test finger results in no hazard. b) Test hook of fig. 4 for 10 s (20 ) : Test with test hook results in no hazard. c) 30 mm diameter test tool for 5 s (100 or 250 ) : Test with 250 results in no damage. 9.2 o hazard after removing a cover by hand.: o cover removable by hand. 10 Insulation requirements 10.1 Insulation resistance (MΩ) at least 2 MΩ min. after surge test for basic and 4 MΩ min. for reinforced insulation.. : >20MΩ (Surge test is performed between primary circuits and secondary output circuits) 10.2 Humidity treatment 48 h or 120 h.: erformed for 120 h at temp. 40 o C and a relative humidity 95% TRF o. IEC60065_I

14 - age 14 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict 10.3 Insulation resistance and dielectric strength between mains terminals...: Insulation Resistance and dielectric strength across BASIC or SULEMETARY insulation (Class 1) : Insulation resistance and dielectric strength across REIFORCED insulation (Class II)..: See appended table See appended table Fault conditions 11.1 o shock hazard under fault condition : o electric shock hazard under fault conditions Heating under fault condition.: Flames extinguish within 10 seconds...: See below. either danger of fire to surroundings nor abnormal heat developed. o hazard from softening solder...: Considered. Soldered terminations not used as protective mechanism..: o soldered terminations used Measurement of temperature rises..: See appended table Temperature rise of accessible parts...: See appended table Temperature rise of parts, other than windings, providing electrical insulation : Temperature rise of printed circuit boards (CB) exceeding the limits of table 3 by max. 100 K for max. 5 min...: a) Temperature rise of printed circuit boards (CB) to , exceeding the limits of table 3 by not more than 100 K for an area not greater than 2 cm² : b) Temperature rise of printed circuit boards (CB) to up to 300 K for an area not greater than 2 cm² for a maximum of 5 min.: Meets all the special conditions if conductors on printed circuit boards are interrupted...: See appended table Temp. rise of CB do not exceed limits of table 3. Temp. rise of CB do not exceed limits of table 3. Temp. rise of CB do not exceed limits of table 3. o conductors are interrupted / peeled / loosened during fault conditions TRF o. IEC60065_I

15 - age 15 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict Class I protective earthing maintained.: Temperature rise of parts acting as a support or mechanical barrier..: Temperature rise of windings : Temperature rise of parts not subject to the limits of to : Class II apparatus. See appended table See appended table o excessive temperature observed/measured on other parts. (see appended table 11.2) 12 Mechanical strength Bump test where mass >7 kg...: Mass < 7 kg Vibration test : o applicable Impact hammer test...: o damage in the sense of this standard. Steel ball test...: Drop test for portable apparatus where mass 7 kg...: Thermoplastic enclosures stress relief test.: 12.2 Fixing of knobs, push buttons, keys and levers..: o damage in the sense of this standard. o damage in the sense of this standard. Test is carried out at 94 C / 7h. o risk of shrinkage or distortion on enclosures due to release of internal stresses. o knobs, push buttons, keys and levers Remote controls with hazardous live parts.: o remote control Drawers (pull test 50, 10 s) : 12.5 Antenna coaxial sockets providing isolation : 12.6 Telescoping or rod antennas construction..: o drawers. o antenna socket which isolated hazardous live parts from accessible parts. o telescoping or rod antenna Telescoping or rod antennas securement...: o telescoping or rod antenna. TRF o. IEC60065_I

16 - age 16 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict 13 Clearances and creepage distances 13.1 Clearances in accordance with 13.3 : TRF o. IEC60065_I Creepage distances in accordance with 13.4.: See 13.3 See Determination of operating voltage.. : The rms and peak voltage of the appliance is mains voltage 240V max. The unit was connected to a 240V T power system. The highest operating voltages are measured on transformers (T1). (appended table 13.2) 13.3 Clearances Refer to below General : Clearance distances are in compliance with table 8, 9. (see appended table 13.3 and 13.4) Circuits conductively connected to the mains comply with table 8 and, where applicable, table 9..: Circuits not conductively connected to the mains comply with table 10...: Measurement of transient voltages..: (see appended table 13) (see appended table 13) o used Creepage distances...: Creepage distances are in compliance with table 11. (see appended table 13). Creepage distances greater than table 11 minimum values... : one 13.5 rinted boards Clearances and creepage distances between conductors on printed circuit boards, one of which may be conductively connected to the mains, as in fig. 10 : Type B coated printed circuit boards complying with IEC (basic insulation only)..: (see appended table 13) o coated CB.

17 - age 17 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict 13.6 Conductive parts along uncemented joints clearances and creepage distances comply with 13.3 and : Conductive parts along reliably cemented joints comply with 8.8 : Temperature cycle test and dielectric strength test : 13.7 Enclosed, enveloped or hermetically sealed parts not conductively connected to the mains, clearances and creepage distances as in table 12 : 13.8 arts filled with insulating compound, meeting the requirements of 8.8 : o uncemented joints. o such part used. Optocoupler (IC2) is approval component, see list of critical components. 14 Components 14.1 Resistors See below: a) Resistors between hazardous live parts and accessible metal parts : b) Resistors, other than between hazardous live parts and accessible parts..: Resistors separately approved.: o such resistors used. o such resistors used Capacitors and RC units See below. Capacitors separately approved... : Y capacitors tested to IEC , 2 nd edition : X capacitors tested to IEC , 2 nd edition : Capacitors operating at mains frequency but not connected to the mains: tests for X2 : Capacitors with volume exceeding 1750 mm³, where short-circuit current exceeds 0,2 A: compliance with IEC , 4.38 category B or better : Yes, see below. Capacitor (CY1) is Y1 type, see list of critical components. o such capacitors used. o such capacitors used. Compliance due to high short circuit current not relevant because of fuse F1. TRF o. IEC60065_I

18 - age 18 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict TRF o. IEC60065_I Capacitors with volume exceeding 1750 mm³, mounted closer to a potential ignition source than table 5 permits: compliance with IEC , 4.38 category B or better : Shielded by a barrier acc. to / table 21 or metal. : C1, C2 with metal housing. o barrier required, see above Inductors and windings See below. Comply with IEC , IEC (as relevant) and clause : Transformers and inductors marked with manufacturer's name and type.: Transformers and inductors separately approved.: o Refer to cl See appended table General : Isolating transformers, ref. Transformers spec. Insulation material complies with clause Insulation material complies with table 21 on flammability class Constructional requirements See below Clearances and creepage distances comply with clause 13..: Transformers meet the constructional requirements.: Transformer complied with clause 13. Complied, refer to appended table Separation between windings Refer below Class II transformers have adequate separation between hazardous live parts and accessible parts (double or reinforced insulation)...: Coil formers and partition walls > 0,4 mm...: Class I transformers, with basic insulation and protective screening only if all 7 conditions of are met.: Separating transformers with at least basic insulation: Insulation between HAZARDOUS LIVE parts and ACCESSIBLE parts Transformer have adequate separation and construction. Min. 0.5mm. o such transformer used. Windings are of Class II construction. o such transformer used. Windings are of Class II construction. Refer below

19 - age 19 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict Class II transformers have adequate insulation between hazardous live parts and accessible parts (double or reinforced insulation)...: Coil formers and partition walls > 0,4 mm...: Class I transformers have adequate insulation between hazardous live parts and accessible conductive parts or those conductive parts or protective screens connected to a protective earth terminal : Winding wires connected to protective earth have adequate current-carrying capacity..: 14.4 High voltage components..: High-voltage components and assemblies: U > 4 kv (peak) separately approved...: Component meets category V-1 of IEC : High voltage transformers and multipliers tested as part of the submission : High voltage assemblies and other parts tested as part of the submission : Double or reinforced insulation between hazardous live windings and accessible conductive parts. Min. 0.5mm. Windings of Class II construction used. o high voltage components rotective devices See below rotective devices used within their ratings : F1 T2AH/250V External clearances and creepage distances meet requirement of clause 13 for the voltage across the device when opened...: a) Thermal cut-outs separately approved : Fuse is separately approved, between fuse pad 1 to pad 2. Min. 2.6 mm. o such thermal cut-out. b) Thermal cut-outs tested as part of the submission: a) Thermal links separately approved..: o thermal links. b) Thermal links tested as part of the submission.: Thermal devices re-settable by soldering : o such thermal device TRF o. IEC60065_I

20 - age 20 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict Fuse-links in the mains circuit according to IEC : Correct marking of fuse-links adjacent to holder : TRF o. IEC60065_I Fuse is approved according to IEC 60127, see list of critical components. Fuse marked on CB adjacent to component as: F1 T2AH/250V ot possible to connect fuses in parallel.: o fuse holder so designed that fuse-links can be connected in parallel ot possible to touch hazardous live parts when replacing fuse-links without the use of a tool..: o replacement of fuse possible by hand TC-S thermistors comply with IEC : o TC used. TC-S devices (15 W) category V-1 or better : Circuit protectors have adequate breaking capacity and their position is correctly marked...: Only standard fuse used Switches (see appended table) o switches a) Separate testing to IEC including: operations - ormal pollution suitability - Resistance to heat and fire level 3 - Make and break speed independent of speed of Actuation - V-0 compliance with annex G, G : b) Tested in the apparatus.: Switch controlling > 0.2A with open contact voltage > 35 V (peak)/24 V dc complying with , and V-0 in annex G, G.1.1.: Switch controlling > 0.2A with open contact voltage < 35 V (peak)/24 V dc complying with and V-0 in annex G, G.1.1 : Switch controlling < 0.2A with open contact voltage > 35 V (peak)/24 V dc complying with and V- 0 in annex G, G.1.1 : Switch tested to b) constructed to IEC subclause 13.1 and has making/breaking action independent of speed of actuation...:

21 - age 21 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict Switch tested to b) compliant with IEC subclause d) and m) not attaining excessive temperatures in use : Switch tested to b) has adequate dielectric strength....: Mains switch controlling mains socket outlets additional tests to IEC : TRF o. IEC60065_I Socket outlet current marking correct..: o mains socket outlet Safety interlocks o safety interlocks. Safety interlocks to 2.8 of IEC : 14.8 Voltage setting devices and the like.: Voltage setting device not likely to be changed accidentally... : o voltage selector Motors o motor Endurance test on motors.: Motor start test : Dielectric strength test : ot adversely affected by oil or grease etc....: rotection against moving parts...: Motors with phase-shifting capacitors, three-phase motors and series motors meet clause. B.8, B.9 and B.10 of IEC 60950, Annex B.: Batteries o batteries Batteries mounted with no risk of accumulation of flammable gases : o possibility of recharging non-rechargeable batteries : Recharging currents and times within manufacturers limits.: Lithium batteries discharge and reverse currents within the manufacturers limits.: o lithium batteries provided.

22 - age 22 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict Battery mould stress relief.: Battery drop test..: Optocouplers Optocuplers (IC2) is approval component, see list of critical components. Optocouplers comply with Cl. 8 : Internal and external dimensions to or alternatively 13.6 (jointed insulation) : Surge suppression varistors Certified varistor (MOV) is between Line and eutral (located after fuse). Approved component used, refer to table 14. Comply with IEC : ot connected between mains and accessible parts except for earthed parts of permanently connected apparatus. : Complies with the current pulse, fire hazard and thermal stress requirements of : Approved component used, refer to appended table 14. Approved component used, refer to appended table Terminals Mains plug, appliance inlet, interconnection couplers and mains socket-outlet meet the appropriate standard... : TRF o. IEC60065_I Overloading of plugs or appliance inlets prevented if the apparatus has mains socket outlets..: Overloading of internal wiring prevented if the apparatus has mains socket outlets.: Connectors for antenna, earth, audio, video or data... : o risk of insertion in mains socket-outlets.: The main plug complied with appropriate component standard. o mains supply of this unit to other equipment. o such parts. o such parts. o such parts.

23 - age 23 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict o risk of insertion into audio or video: outlets marked with the symbol of : Output terminals of a.c. adaptors or similar devices not compatible with household mains socket-outlets : o such devices used rovision for protective earthing Class II apparatus. Accessible conductive parts of Class I equipment reliably connected to earth terminal, within equipment rotective earth conductors correctly coloured..: Equipment with non-detachable mains cord provided with separate protective earth terminal near mains input...: rotective earth terminal resistant to corrosion..: Earth resistance test: < 0,1 Ω at 25 A.: 15.3 Terminals for external flexible cords and for permanent connection to the mains supply Adequate terminals for connection of permanent wiring.... : Reliable connection of non-detachable cords.: ot soldered to conductors of a printed circuit board : Adequate clearances and creepage distances between connections should a wire break away : Wire secured by additional means to the conductor : Screws and nuts clamping conductors have adequate threads: ISO 261, ISO 262 or similar.: Soldered conductors wrapped around terminal prior to soldering or held in place by additional means..: Clamping of conductor and insulation if not soldered or held by screws : Terminals allow connection of appropriate crosssectional area of conductors, for the rated current of the equipment.: See below: Apparatus is not for permanent connection. Direct plug-in apparatus. o external mains supply conductor used. o terminals used. o terminals used Terminals to have sizes required by table 16.: o terminals used. TRF o. IEC60065_I

24 - age 24 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict Terminals clamp conductors between metal and have adequate pressure : Terminals designed to avoid conductor slipping out when tightened or loosened..: Terminals adequately fixed to avoid loosening when the clamping is tightened or loosened and stress on internal wiring is avoided......: Terminals carrying a current more than 0,2 A: contact pressure not transmitted by insulating material except ceramic. : Termination of non-detachable cords: wires terminated near to each other...: Terminals located and shielded: test with 8 mm strand : o terminals used. o terminals used. o terminals used Devices forming a part of the mains plug See below o undue strain on mains socket-outlets : Max m<0.25m Device complies with standard for dimensions of mains plugs.: Device has adequate mechanical strength (tests a,b,c). : The EU plug complies with the relevant standard, others plug should be evaluated when marketing. Compliance. 16 External flexible cords 16.1 Mains cords sheathed type, complying with IEC for VC or IEC for synthetic rubber cords. : on-detachable cords for Class I have green/yellow core for protective earth.: ot provided. TRF o. IEC60065_I

25 - age 25 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict 16.2 Mains cords conductors have adequate crosssectional area for rated current consumption of the equipment : 16.3 a) Flexible cords not complying with 16.1, used for interconnections between separate units of equipment used in combination and carrying hazardous live voltages, have adequate dielectric strength : b) Flexible cords not complying with 16.1, withstand bending and mechanical stress (3.2 of IEC ): 16.4 Flexible cords used for connection between equipment have adequate cross-sectional areas to avoid temperature rise under normal and fault conditions. : 16.5 Adequate strain relief on external flexible cords.: ot possible to push cord back into equipment..: Strain relief device unlikely to damage flexible cord... : For mains cords of Class I equipment, hazardous live conductors become taut before earth conductor : 16.6 Apertures for external flexible cord: no risk of damage to the cord during assembly or movement in use : 16.7 Transportable musical instruments and amplifiers fitted with detachable cord set with appliance inlet to IEC : Transportable musical instruments and amplifiers fitted with detachable cord sets or with means of stowage to protect the cord...: ot provided. ot provided. ot provided. ot provided. ot provided. ot transportable musical instruments or associated amplifier. 17 Electrical connections and mechanical fixings 17.1 Torque test to table 20 o screw. - screws into metal: 5 times...: TRF o. IEC60065_I

26 - age 26 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict - screws into non-metallic material: 10 times..: 17.2 Correct introduction into female threads in nonmetallic material..: 17.3 Cover fixing screws: captive..: on-captive fixing screws: no hazard when replaced by a screw whose length is 10 times its diameter..: 17.4 o loosening of conductive parts carrying a current > 0,2 A.. : 17.5 Contact pressure not transmitted through plastic other than ceramic for connections carrying a current > 0,2 A.. : 17.6 Stranded conductors of flexible supply cords carrying a current > 0,2 A with screw terminals not consolidated by solder : 17.7 Cover fixing devices other than screws have adequate strength and their positioning is unambiguous... : 17.8 Fixing devices for detachable legs or stands 2.4 mm for fixing plactic enclosure and 0.4m at 10 times. Correct introduction of screws. on-captive screws used, see below on-captive fixing screws used, it will not cause a reduction of clearance and creepage distance. o such screw. o such screw. o screw terminal. Cover fixing by screw and snap fastener, after 10 times removed and replace, the apparatus compliance with a) and b) o such parts. provided : 17.9 Internal pluggable connections, affecting safety, unlikely to become disconnected..: Connections complies, checked by inspection 18 Mechanical strength of picture tubes and protection against the effects of implosion icture tube separately approved to IEC : icture tube separately approved to : o picture tube used. TRF o. IEC60065_I

27 - age 27 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict 18.1 icture tubes >16 cm intrinsically protected....: on-intrinsically protected tubes >16 cm used with protective screen.....: rotective film as part of implosion protection: edges covered by enclosure..... : 18.2 Intrinsically protected tubes: tests on 12 samples..: Samples subject to ageing: 6 samples : Samples subject to implosion test: 6 samples : Samples subject to mechanical strength test (steel ball): 6 samples...: 18.3 on-intrinsically protected tubes tested to : 19 Stability and mechanical hazards Mass of the equipment exceeding 7 kg...: Apparatus intended to be fastened in place suitable instructions..: 19.1 Test on a plane, inclined at 10 o to the horizontal...: force applied vertically downwards...: force, or 13% of weight, applied horizontally to point of least stability..: 19.4 Edges or corners not hazardous...: 19.5 Glass surfaces (exc. laminated) with an area exceeding 0,1 m² or maximum dimension > 450 mm, pass the test of : Mass < 7 kg. There is no hazardous edges or corners. o glass surface Wall or ceiling mountings adequate.: ot wall or ceiling mounting. TRF o. IEC60065_I

28 - age 28 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict 20 Resistance to fire 20.1 Electrical components and mechanical parts See below: TRF o. IEC60065_I a) Exemption for components contained in an enclosure of material V-0 to IEC with openings not exceeding 1 mm in width : b) Exemption for small components as defined in : Electrical components meet the requirements of Clause 14 or : Insulation of internal wiring working at voltages > 4 kv or leaving an internal fire enclosure, or located within the areas mentioned in Table 21, not contributing to the spread of fire...: Material of printed circuit boards on which the available power exceeds 15 W at a voltage between 50 V and 400 V (peak) a.c. or d.c. meets V-1 or better to IEC60707, unless used in a fire enclosure..: Material of printed circuit boards on which the available power exceeds 15 W at a voltage >400 V (peak) a.c. or d.c. meets V-0 to IEC : Components and parts not covered by , and (other than fire enclosures) mounted nearer to a potential ignition source than the distances in Table 21 comply with the relevant flammability category in Table 21.: Components and parts as above but shielded from a potential ignition source, with the barrier area in accordance with Table 21 and fig. 13..: Apparatus with voltages >4kV under normal operating conditions and distances to the enclosure exceed those specified Table 21, flammability classification HB40 or better is required for the enclosure.....: The apparatus enclosure is made of V-0 (UL approval). o flammability requirements for the internal components. o openings provided. CB is flammability class V-1, and except is made for metal enclosure. Electrical components comply with flammability requirements in clause 14. o wires wiring working at voltages > 4 kv. The CB is of base material with flammability category V-1 (UL approval). See List of Critical Components. The CB is of base material with flammability category V-1 (UL approval) and enclosure is made a V-0. See List of Critical Components. Transformer bobbin and large capacitor. See appended table 14. o shield required. o voltages >4kV Fire enclosure o voltage >4 KV.

29 - age 29 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict otential ignition sources with open circuit voltage > 4 kv (peak) a.c. or d.c. contained in a fire enclosure to V- 1..: Internal fire enclosures with openings not exceeding 1 mm in width and with openings for wires completely filled..: Requirements of and met by an internal fire enclosure.: o internal fire enclosure. o internal fire enclosure. A Annex A, Additional requirements for apparatus with protection against splashing water A.5 Marking and instructions A.5.1 j) Marked with IX4 (IEC 60529), a) does not apply... : A.10.2 Insulation requirements A A Enclosure provides protection against splashing water...: Humidity treatment carried out for 7 days : B Annex B, Apparatus to be connected to the TELECOMMUICATIO ETWORKS TRF o. IEC60065_I Complies with IEC clause 1..: ot connected to telecommunication network. Complies with IEC clause 2..: Complies with IEC clause 3 but with modified to of this standard... : Complies with IEC clause 4 but with 4.1.2, and modified in accordance with annex B of this standard : Complies with IEC cause 5 but with modified in accordance with annex B of this standard... : Complies with IEC clause 6..: Complies with IEC clause 7...:

30 - age 30 of 40 - Report o IEC Clause Requirement Test Result - Remark Verdict Complies with IEC annex A, B and C...: L Annex L, Additional requirements for electronic flash apparatus for photographic purposes L. 5 Marking and instructions L. 5.4 Instructions for battery chargers and Supply apparatus indicating type or model number of flash apparatus with which it is to be used : Instructions for flash apparatus indicating type or model number of battery chargers or Supply apparatus with which it is to be used : L. 7 Heating under normal operating conditions L7.1.5 & L Lithium batteries meet permissible temp rise in Table 3, unless comply with or of IEC : L. 9 Electric shock hazard under normal operating conditions L Terminals to connection to synchroniser not HAZARDOUS LIVE : L.10 Insulation requirements L High frequency pulse ignition..: L. 12 Mechanical strength L Windows for flash tubes are excluded from steel ball impact test...: L. 14 Components L Mains switch characteristics appropriate to its function under normal conditions.: L. 20 Resistance to fire L c) Trigger coil for discharge purpose is not considered to be a OTETIAL IGITIO SOURCE..: TRF o. IEC60065_I

31 - age 31 of 40 - Report o TABLE: temperature rise measurements Operating conditions ower consumption in the OFF/Stand-by position of the functional switch (W) o Stand-by function. Un (V) In (A) n (W) out (W) 90V/50Hz V/60Hz V/50Hz V/60Hz V/50Hz V/60Hz V/50Hz V/60Hz V/50Hz V/60Hz Loudspeaker impedance (Ω)...: Several loudspeaker systems Marking of loudspeaker terminals TRF o. IEC60065_I

32 - age 32 of 40 - Report o Monitored point: dt (K) ermitted dt (K) Applied voltage and position of the unit 90V/50Hz 90V/50Hz 264V/50Hz 264V/50Hz -- horizontal vertical horizontal vertical lug holder rimary lead wire MOV body L1 coil CB under BD C1 body C2 body CB under Q T1 coil T1 core IC2 body CY1 body CB under D Output cord Enclosure (inside) near T Enclosure (outside) near T Ambient supplementary information: Max. Ambient is 45 C. Temperature limits include less 10K for thermocouple measurement method. If no limit is stated, temperature is for reference only. *) Limited dt (K) is considered (moderate climate is considered, corresponding to an ambient of 45 C). TRF o. IEC60065_I

33 - age 33 of 40 - Report o TABLE: softening temperature of thermoplastics Temperature T of part lug holder, type SE1X(GG)(f1) supplementary information: Bobbin of other transformer or choke are made of phenolic. T - normal conditions ( o C) 55.9 C at ambient= 45.3 C T - fault conditions ( o C) 39.0 C at ambient= 26.0 C Min T softening ( o C) TABLE: touch current expressed as voltages U1 and U2 in Annex D Location Measured U1 V (peak) Measured U1 V (DC) Measured U2 V (peak) Limits : U1 Max 35V (peak) U1 Max 1.0V (DC) U2 Max 0.35V (peak) Line phase and output connector eutral phase and output connector Line phase and plastic enclosure (with foil) eutral phase and plastic enclosure (with foil) ass ass ass ass supplementary information: Bridging capacitor is rated to max. according to list of critical components TABLE: insulation resistance measurements Insulation resistance R between: R (MΩ) Required R (MΩ) Between poles of the circuit directly connected to the mains (primary fuse disconnected) Between parts separated by double or reinforced insulation: Mains poles and sec. parts >20MΩ 2 >40MΩ 4 supplementary information: TRF o. IEC60065_I

34 - age 34 of 40 - Report o TABLE: electric strength measurements Test voltage applied between: Test voltage (V) Breakdown Between poles of the circuit directly connected to the mains (primary fuse disconnected) Between parts separated by double or reinforced insulation: Mains poles and secondary parts. Between parts separated by double or reinforced insulation: Mains poles and enclosure with foil. supplementary information: 2120Vdc 4240Vdc 4240Vdc o o o 11.2 TABLE: summary of fault condition tests Voltage (V) 0,9 or 1,1 times rated voltage...: 264V Ambient temperature ( o C)...: See below Monitored point: Under fault conditions specified below dt (K) ermitted dt (K) BD1 s-c 1) 1 sec Fuse opened immediately, no damaged, no hazards. C1 s-c 1) 1 sec Fuse opened immediately, no damaged, no hazards IC1 (2-3) s-c hrs ormal operation, no damaged, no hazards. T1 coil = 53.3K, ambient =25.9 C 130*) Q1 (G-S) s-c min. Unit shut down, no damage, no hazards. -- Q1 (G-D) s-c 1) 1 sec Fuse opened immediately, no damaged, no hazards. -- Q1 (D-S) s-c 1) 1 sec Fuse opened immediately, no damaged, no hazards. R4 s-c hrs ormal operation, no damaged, no hazards. -- T1 coil = 53.3K, ambient =25.9 C 130*) IC2 (1-2) IC2 (3-4) s-c min. Unit shut down, no damage, no hazards. s-c min. Unit shut down, no damage, no hazards TRF o. IEC60065_I

35 - age 35 of 40 - Monitored point: Under fault conditions specified below IC2 (1) IC2 (3) T1 (2-4) T1 (9-10) o-c min. Unit shut down, no damage, no hazards. o-c min. Unit shut down, no damage, no hazards. s-c min. Unit shut down, no damage, no hazards. s-c min. Unit shut down, no damage, no hazards. Output s-c min. Unit shut down, no damage, no hazards. Output o-l hrs Unit oscliiated. Output loaded at 1.6A. o damage, no hazards. Winding temperature rise measurements Report o dt (K) T1 coil = 70.7, ambient = 26.0 o C ermitted dt (K) Ambient temperature t1 ( o C)...: Ambient temperature t2 ( o C)...: supplementary information: S-c: short circuit, o-l: overload, o-c: open circuit. 1) Fuse current is more than fuse rating times 2.1. Electric shock hazards measurement as clause 9 on each fault condition, the value does not exceed the limite of clause *) Limited dt (K) is considered (moderate climate is considered, corresponding to an ambient of 45 C). 130 *) TRF o. IEC60065_I

36 - age 36 of 40 - Report o TABLE: clearances and creepage distances Rated supply voltage: 240V ollution degree: II Material Group: llla + IIIb 2 force on internal parts applied: Compliance 30 force on outside of conductive enclosure applied: Compliance Location Operating Voltage Clearance (mm) Creepage (mm) V peak V rms Min. Actual Min. Actual Circuits conductively connected to the mains (use Tables 8, 9 and 11): see note below. Basic: Line eutral before fuse Basic: F1, pad Reinforced: CY1(prim.) CY1 (sec.) Reinforced:T1 (prim.) T1 (sec.) Reinforced: IC2 (prim.) IC2 (sec.) Reinforced: Components (prim.) enclosure (sec.) otes: - Glue add Line/nertual wires and output wires, pass 2 force. "Min" = minimum required. "Actual = Actual dimensions measured. 1) Trace under transformer (T1) TABLE: Operating voltage measurement Location eak voltage (V) RMS voltage (V) Comments T1 in T1 in T1 in T1 in T1 in T1 in Max. Vpeak and rms Value T1 in T1 in IC2 in Max. Vpeak and rms Value IC2 in IC2 in IC2 in CY1 in TRF o. IEC60065_I

37 - age 37 of 40 - Report o supplementary information: TABLE: Transformers construction Loc. Tested insulation Operating voltage peak / V (13.2) Operating voltage rms / V (13.2) Min. electric strength / V (10.3) Min. clearance / mm Min. creepage distance / mm (13.4) Min. insu. / mm; number of layers (8.8) (13.3) T1 Core - Secondary pins V ac layers min. or 0.4 mm Loc. Tested insulation Test voltage/ V Actual clearance / mm Actual creepage dist./ mm T1 Core - Secondary pins 3000V ac *) Actual insu. / mm; number of layers Supplementary information: *) Secondary windings are triple insulated, ref. list of critical components. The creepage distance from prim. winding to core is 0mm. Core is considered as pri, part. TRF o. IEC60065_I

38 - age 38 of 40 - Report o TABLE: list of critical components and materials Component CE lug Enclosure lug holder Fuse (F1) Varistor (MOV) (Optional) *) Choke (L1) (Optional) o bobbin Bridge Diode (BD1) Bulk capacitor (C1) MOSFET (Q1) Bridge-Caps. (CY1) (Optional) Optocoupler (IC2) Transformer (T1) 1) Triple insul. wire Manufacturer/ trademark Eastern Frontier Co., Ltd. Bayer Materialscience AG Sabic Innovative lastics China Co., Ltd. XC Electronics (Shenzhen) Thinking Lien Shun Type/model Value / rating Standard Approval/ Reference EFS A, 250Vac IEC , Tested in the 30CE E50075 equip V-0 min., 1.5 UL94 UL mm thick min., 115ºC min. SE1X(GG)(f1) V-1 min., 1.5 mm thick min., 105ºC min. UL94 3T-Series T2AH, 250Vac IEC/E , IEC/E TVR D471K 350Vac UL1449, IEC , IEC UL VDE UL, VDE UL, VDE Eastern Frontier EFT C -- Tested in the equip. Various Various 0.8A, min. 600Vac Various Various Min 15μF, min. 400V, min. 105 C Various Various Min. 4A, min, 600V TDK CD Max.2200pF, Jyh Chung JD Min. 250Vac, Vishay VY1, WK 100 C, Y1 type Matsushita S-A Success SE, SB Murata KX Haohua CT 7 Cosmo Vishay Bright Led Fairchild Lite-On Eastern Frontier K1010, KC817 TCET110X series BC-817 H11A817X LTV-816., LTV817. EFT See appended opto electronic devices Min. 100 C Class B -- Tested in the equip. -- Tested in the equip. -- Tested in the equip. IEC VDE, UL 2 ed., UL1414 VDE, UL VDE, UL VDE, UL VDE, UL VDE, UL VDE, UL IEC , UL 1577 IEC60065 Clause 14.3 VDE, UL VDE, UL Furukawa TEX-E 130 C IEC/E VDE 2) CB Various Various V-0, min. 105 C UL 796 UL VDE, UL VDE, UL VDE, UL VDE, UL Tested in the equip. TRF o. IEC60065_I

39 - age 39 of 40 - Report o Component Manufacturer/ Type/model Value / rating Standard Approval/ trademark Reference 1 ) an asterisk indicates a mark which assures the agreed level of surveillance Supplementary information: *) Varistor complies with UL ed type 3 which cover the required 15 combination pulses 6kV (1.2/50s)/ 3kA (8/20s) test this is more strict than table I group 1 of IEC ) For bobbin and others material of transformers, refer to transformer specification. 2) o difference between IEC Annex U and IEC Annex H. TRF o. IEC60065_I

40 - age 40 of 40 - Report o Appended OTO ELECTROIC DEVICE Manufacturer Cosmo / Cosmo / Vishay / Bright Led / Fairchild / Lite-On Type K1010 / KC817 / TCET110X series / BC-817 / H11A817X / LTV-816. / LTV817. Separately tested Connected over insulation External creepage distance Internal creepage distance Distance through insulation Tested under the following Tested by FIMKO Reinforced insulation 8.0 / 8.0 / 8.4 / 7.6 / >7 / 7.8 mm 5.3 / 5.3 / 4.7 / 7.6 / -*) / 5.2 mm 0.5 / 0.5 / 0.6 / 0.5 / >1 / 0.8 mm R, S, B conditions Input Output Comments - *) There is not any internal distance. Test according to IEC , cl has been carried out ten times for components at 100 C / 25 C / 0 C / 25 C. Humidity treatment of 48 h as well as electric strength tests at 3000 V / 1 min. and 5000 V / 1 min. were carried out to the component after thermal cycling test. TRF o. IEC60065_I

41 IEC60065(ed.7); am.1 (2005) - age 1 of Report o IEC ATTACHMET Clause Requirement + Test Result - Remark Verdict ATTACHMET TO TEST REORT IEC EUROEA GROU DIFFERECES AD ATIOAL DIFFERECES Audio, video and similar electronic apparatus Safety requirements Differences according...: E 60065: A1:2006 Attachment Form o...: Attachment Form Originator... : Master Attachment Form... : EU_GD_IEC60065I Intertek Semko AB Copyright 2008 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. IEC 60065, GROU DIFFERECES (CEELEC common modifications (E)) Clause Requirement + Test Result - Remark Verdict Contents Add the following annexes: Annex ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications (See the CB Bulletin) Annex ZB (nominative) Special national conditions Annex ZC (informative) A-deviations 3.1 Add the following indent at the end of the list - Exposure to excessive sound pressures from headphones or earphones OTE A new method of measurement is described in E , Sound system equipment: Headphones and earphones associated with portable audio equipment Maximum sound pressure level measurement methodology and limit considerations art 1: General method for one package equipment, and in E , Sound system equipment: Headphones and earphones associated with portable audio equipment Maximum sound pressure level measurement methodology and limit considerations art 2: Guidelines to associate sets with headphones coming from different manufacturers Replace the text of the note by: 5.1.i) OTE For ROUTIE TEST reference is made to E Add the following note: OTE For RATED OWER COSUMTIO measurements of TVs reference is made to E Replace the entire subclause by: Apparatus including a potential source of ionizing radiation shall be so constructed that personal protection against ionizing radiation is provided under normal operating conditions and under fault conditions. o sound system. Considered. ot TV apparatus. o ionizing radiation in the equipment

42 IEC60065(ed.7); am.1 (2005) - age 2 of Report o IEC ATTACHMET Clause Requirement + Test Result - Remark Verdict Compliance is checked by measurement under the following conditions: In addition to the normal operating conditions, all controls adjustable from the outside BY HAD, by any object such as a tool or a coin, and those internal adjustments or pre-sets which are not locked in a reliable manner, are adjusted so as to give maximum radiation whilst maintaining an intelligible picture for 1 h, at the end of which the measurement is made. OTE Soldered joints and paint lockings are examples of adequate locking. The amount of ionizing radiation is regulated by European Council Directive 96/29/Euratom of 13 May This directive requires that at any point 10 cm from the outer surface of the apparatus, the dose-rate shall not exceed 1µSv/h (0.1 mr/h) taking account of the background level. Moreover, the measurement shall be made under fault conditions causing an increase of the highvoltage, provided an intelligible picture is maintained for 1 h, at the end of which the measurement is made. A picture is considered to be intelligible if the following conditions are met: - a scanning amplitude of at least 70% of the usable screen width; - a minimum luminance of 50 cd/m² with locked blank raster provided by a test generator; - a horizontal resolution corresponding to at least 1.5 MHz in the centre, with a similar vertical degradation; - not more than over flashover per 5 min Delete note 4. Deleted. 14 Delete note 4 and note 5. Deleted Delete notes 1 and 2. Deleted Delete note 2. Deleted Delete note 1. Deleted Delete the note. Deleted. 20 Delete note 2. Deleted. Annex B Replace note 1 by: In the CEELEC countries listed in IEC 62151, special national conditions apply. o TV circuits. Annex G Delete the note. Deleted. Annex J.2 Delete the notes of Table J.1. Deleted. Annex Add after the introduction: For ROUTIE TEST reference is made to E Considered.

43 IEC60065(ed.7); am.1 (2005) - age 3 of Report o IEC ATTACHMET Clause Requirement + Test Result - Remark Verdict Bibliograph y Annex ZA (normative) Add the following standards: E : 2000, Sound system equipment: Headphones and earphones associated with portable audio equipment Maximum sound pressure level measurement methodology and limit considerations art 1: General method for one package equipment. re (under consideration), Sound system equipment: Headphones and earphones associated with portable audio equipment Maximum sound pressure level measurement methodology and limit considerations art 2: Guidelines to associate sets with headphones coming from different manufacturers. Add the following notes for the standards indicated: IEC OTE arts 9 and 17: 1998 are harmonized as Ens (not modified). IEC OTE artly harmonized in the E 60169/HD 134 series (not modified). IEC OTE Harmonized as HD 27 S1: 1978 (not modified). IEC OTE Harmonized as E : 1997 (not modified). IEC OTE Harmonized as E : 2000 (not modified). IEC OTE Harmonized as E series (not modified). IEC OTE Harmonized as E 61040: 1992 (not modified). IEC OTE Harmonized as E : 1997 (not modified). IEC OTE Harmonized as E : 1997 (not modified). IEC OTE Harmonized as E : 1997 (not modified). Other international publications quoted in this standard with the references of the relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). OTE When an international standard has been modified by common modification, indicated by (mod), the relevant E/HD applies.

44 IEC60065(ed.7); am.1 (2005) - age 4 of Report o IEC ATTACHMET Clause Requirement + Test Result - Remark Verdict Annex ZA Cont.

45 IEC60065(ed.7); am.1 (2005) - age 5 of Report o IEC ATTACHMET Clause Requirement + Test Result - Remark Verdict Annex ZA Cont. GROU DIFFERECES FOR AMEDMET 1 COMMO MODIFICATIOS 5.1 i) in E 60065:2002 Replace the note by: OTE For RATED OWER COSUMTIO measurements of TVs reference is made to E Measurements are done in the O (play) operating mode Add the following indent: za) A warning that excessive sound pressure from earphones and headphones can cause hearing loss in E 60065:2002 Replace the subclause by: Ionizing radiation Equipment that might produce ionizing radiation is checked by measuring the amount of radiation. The amount of radiation is determined by means of a radiation monitor of the ionizing chamber type with an effective area of mm2 or by measuring equipment of other types giving equivalent results. Measurements are made with the equipment on test operating at the most unfavourable supply voltage (see 4.2) and with operator controls and service controls adjusted so as to give maximum radiation whilst maintaining the equipment operative for normal use. Internal preset controls not intended to be adjusted during the lifetime of the equipment are not considered to be service controls. At any point 100 mm from the surface of the operator access area, the dose-rate shall not exceed 1 μsv/h (0,1 mr/h) (see ote). Account shall be taken of the background level. OTE These values appear in Directive 96/29/Euratom. Bibliograp hy in E 60065:2002 Replace the paragraph related to pre by: E :2003, Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - art 2: Matching of sets with headphones if either or both are offered

46 IEC60065(ed.7); am.1 (2005) - age 6 of Report o IEC ATTACHMET Clause Requirement + Test Result - Remark Verdict separately E 60065:2002/A1: Bibliograp hy in IEC 60065:2001 /A1:2005 Add the following notes for the standards indicated: IEC OTE Harmonized as E : A1:1994 (not modified). IEC OTE Harmonized as E : A2:1991 (not modified). ZB AEX ZB TO E 60065, SECIAL ATIOAL CODITIOS (E) DK: The following is added: Certain types of CLASS I apparatus, see , may be provided with a plug not establishing earthing continuity when inserted in Danish socketoutlets. Justification: Heavy Current Regulations, Section O: To the second paragraph the following is added: In orway, due to the IT power distribution system used, the a.c. MAIS supply voltage is considered to be equal to the line-to-line voltage, and will remain 230 V in case of a single earth fault. Justification: Based on a use in orway of an IT power distribution system where the neutral is not provided. Class II apparatus. Considered.

47 IEC60065(ed.7); am.1 (2005) - age 7 of Report o IEC ATTACHMET Clause Requirement + Test Result - Remark Verdict DK: To the first paragraph the following is added: In Denmark, supply cords of single phase appliances having a rated current not exceeding 13 A shall be provided with a plug according to the Heavy Current Regulations Section D1. Appliances of CLASS I provided with socket-outlets with earth contact or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with the Heavy Current Regulations Section D1 standard sheet DK 2-1a. To the second paragraph the following is added: Socket outlets intended for provided power to CLASS II apparatus with a rated current of 2.5 A shall have the following dimensions: Considered. See plug test report. Dimensions in mm Other dimensions shall be in compliance with the Heavy Current Regulations, Section D1, Standard Sheet DKA 1-3 for portable socketoutlets. Shutters are not required. To the third paragraph the following is added: Mains socket-outlets with earthing contact shall be in compliance with the Heavy Current Regulations, Section D1, Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a. Justification: Heavy Current Regulations, Section IE: Apparatus which is fitted with a flexible cable or cord shall be provided with a 13 A plug in accordance with Statutory Instrument 525:97, 13 A lugs and Conversion Adapters for Domestic Use Regulations:1997. Justification: SI 525: 1997 ot applicable.

48 IEC60065(ed.7); am.1 (2005) - age 8 of Report o IEC ATTACHMET Clause Requirement + Test Result - Remark Verdict Cont. O: Mains socket-outlets mounted on CLASS II apparatus shall comply with the specifications given in CEE ubl. 7 as far as a Applicable, with the following amendments: 8 Dimensions a 2.5 A 250 V two-pole socket-outlets for electronic apparatus shall comply with the enclosed Standard Sheet I. Considered. See plug test report. 24 Mechanical strength A 2,5 A 250 V socket-outlets for CLASS II electronic apparatus are tested as specified in of E Also the protecting rim shall be tested Justification: Act of 24 May 1929 relating to supervision of electrical installation (TEA 1929/FEL 1998) UK: Apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to BS 1363 by means of that flexible cable or cord and plug shall be fitted with a standard plug in accordance with Statutory Instrument 1768: 1994: The lugs and Sockets etc. (Safety) Regulations 1994, unless exempted by those Regulations. OTE Standard plug is defined in SI 1768:1994 and essentially means an approved plug conforming to BS 1363 or an approved conversion plug. Justification: SI 1768: 1994 ot applicable.

49 IEC60065(ed.7); am.1 (2005) - age 9 of Report o IEC ATTACHMET Clause Requirement + Test Result - Remark Verdict J.2 O: After Table J.1 the following is added: In orway, due to the IT power distribution system used, the a.c. MAIS supply voltage is considered to be equal to the line-to-line voltage, and will remain 230 V in case of a single earth fault. Justification: Based on a use in orway of an IT power distribution system where the neutral is not provided. Considered. ZC AEX ZC TO E 60065, A-DEVIATIOS (E) 5.1 IT: Additional markings on the outside of the TV ot TV set. receiver in Italian language IT: User instructions in Italian language including a ot TV set. conformity declaration IT: Certification number on the back cover ot TV set. 6.1 o CRT used in the DE: The following requirement applies: equipment. For the operation of any cathode ray tube intended for the display of visual images operating at an acceleration voltage exceeding 40 kv, authorization is required, or application of type approval (Bauartzulassung) and marking. Justification: German ministerial decree against ionizing radiation (Röntgenverordnung), in force since , implementing the European Directive 96/29/EURATOM. OTE Contact address: hysikalisch-technische Bundesanstalt, Bundesallee 100, D Braunschweig, Tel.: Int , Internet: 14 SE: Switches containing mercury such as thermostats, relays and level controllers are not allowed. Justification: Ordinance (1990:944) on rohibition in Connection with handling. Importation and exportation of Chemical roducts (Certain Cases) There are no components containing mercury in the equipment.

50 IEC ed. (2001) - age 1 of Report o ATTACHMET: AUSTRALIA / EW ZEALAD DIFFERECES to IEC th ed. (2001) Test results according to AS/ZS 60065:2003 Clause Requirement Test Result - Remark Verdict ZZ.1 Introduction This Annex sets out variations between this Standard and IEC 60065: These variations indicate national variations for purposes of the IECEE CB Scheme and will be published in the IECEE CB Bulletin. These variations are indicated within the body of the Standard by shading and strikethrough. ZZ.2 Variations The variations are as follows: and Table 3 As an alternative to the method described in footnote f), the following may be used. The ball-pressure test described in AS/ZS may be carried out. Testing is done per footnote f), see main test report. For external parts o external parts. For materials supporting parts conductively connected to the mains 7.2 As an alternative to the second paragraph, the following may be used. The alternative for the method described in footnote h) of Table 3 may be used After the second paragraph, add the following: lugs for the connection of apparatus to mains-powered socket-outlets shall comply with AS/ZS 3112 or AS/ZS Apparatus with a plug portion, suitable for insertion into a 10 A 3-pin flat-pin socket-outlet complying with AS/ZS 3112, shall comply with the requirements of AS/ZS 3112 for equipment with integral pins for insertion into socket-outlets In Table 15, in the second and third rows of the first column replace 6 with In Table 18, in the second and third rows of the first column replace 6 with After item (b) add the following: A flexible cord complying with AS/ZS 3191 need not to undergo this test. 20 Add the following after OTE 2: For alternative test refer to Clause In Table 21, in the third and fourth columns change both HB75 and o requirement to V-1. Testing is done per footnote f), see main test report. Should be considered when marketing in Australian. Should be considered when marketing in Australian. o power supply cord provided. o power supply cord provided. See cl Considered.

51 IEC ed. (2001) - age 2 of Report o After this Clause, add the following: See below Resistance to fire Alternative tests General arts of non-metallic material shall be resistant to ignition and the spread of fire. This requirement does not apply to decorative trims, knobs and other parts unlikely to be ignited or to propagate flames originating from inside the apparatus, or the following: a) Components that are contained in an enclosure having a flammability category of V-0 according to AS/ZS and having openings only for the connecting wires filling the openings completely, and for ventilation not exceeding 1 mm in width regardless of length. b) The following parts which would contribute negligible fuel to a fire: - small mechanical parts, the mass of which does not exceed 4 g, such as mounting parts, gears, cams, belts and bearings; - small electrical components, such as capacitors with a volume not exceeding mm 3, integrated circuits, transistors and optocoupler packages, if these components are mounted on material of flammability category V-1 or better according to AS/ZS The apparatus enclosure is regarded as fire enclosure, made of V-0 and metal. o flammability requirements for the internal components. The CB is of base material is of flammability category V-1. OTE In considering how to minimize propagation of fire and what small parts are, account should be taken of the cumulative effect of small parts adjacent to each other for the possible effect of propagating fire from one part to another. Compliance shall be checked by the tests of , and For the base material of RITED BOARDS, compliance shall be checked by the test of The tests shall be carried out on parts of nonmetallic material which have been removed from the apparatus. When the glow-wire test is carried out, they are placed in the same orientation as they would be in normal use. These tests are not carried out on internal wiring Tests Testing of non-metallic parts art of non-metallic material shall be subject to the glow-wire test of AS/ZS which shall be carried out at 550 C. arts for which the glow-wire test cannot be carried out, such as those made of soft or Refer to cl , not required.

52 IEC ed. (2001) - age 3 of Report o foamy material, shall meet the requirements specified in ISO 9772 for category FH-3 material. The glow-wire test shall not be carried out on parts of material classified at least FH-3 according to ISO 9772 provided that the sample tested was not thicker than the relevant part Testing of insulated parts art of insulating material supporting OTETIAL IGITIO SOURCES shall be subject to the glow-wire test of AS/ZS which shall be carried out at 750 C. The test shall be also carried out on other parts of insulating material which are within a distance of 3 mm of the connection. OTE Contacts in components such as switch contacts are considered to be connections. For parts which withstand the glow-wire test but produce a flame, other parts above the connection within the envelope of a vertical cylinder having a diameter of 20 mm and a height of 50 mm shall be subjected to the needle-flame test. However, parts shielded by a barrier which meets the needle-flame test need not be tested. The needle-flame test shall be made in accordance with AS/ZS with the following modifications: o such part. Clause of AS/ZS Severities Replace with: The duration of application of the test flame shall be 30 s ±1 s. 8.2 Test procedure Replace the first sentence with: The specimen shall be arranged so that the flame can be applied to a vertical or horizontal edge as shown in the examples of figure The first paragraph does not apply. Addition: If possible, the flame shall be applied at least 10 mm from a corner.

53 IEC ed. (2001) - age 4 of Report o Replace with: The test shall be made on one specimen. If the specimen does not withstand the test, the test may be repeated on two further specimens, both of which shall then withstand the test. 10 Evaluation of test results Replace with: The duration of burning (t b ) shall not exceed 30 s. However, for printed circuit boards, it shall not exceed 15 s. The needle-flame test shall not be carried out on parts of material classified as V-0 or V-1 according to AS/ZS provided that the sample tested was not thicker than the relevant part Testing by needle-flame test If parts, other than enclosures, do not withstand the glow wire tests of , by failure to extinguish within 30 s after the removal of the glow-wire tip, the needle-flame test detailed in shall be made on all parts of non-metallic material which are within a distance of 50 mm or which are likely to be impinged upon by flame during the tests of arts shielded by a separate barrier which meets the needle-flame test shall not be tested. OTE 1 If the enclosure does not withstand the glow-wire test the appliance is considered to have failed to meet the requirements of Clause without the need for consequential testing. OTE 2 If other parts do not withstand the glow-wire test due to ignition of the tissue paper and if this indicates that burning or glowing particles can fall onto an external surface underneath the apparatus, the apparatus is considered to have failed to meet the requirements of Clause without the need for consequential testing. OTE 3 arts likely to be impinged upon by the flame are considered to be those within the envelope of a vertical cylinder having a radius of 10 mm and a height equal to the height of the flame, positioned above the point of the material supporting, in contact with, or in close proximity to, connections Testing of printed boards The base material of RITED BOARDS shall be The CB is of base material is of flammability category V-1.

54 IEC ed. (2001) - age 5 of Report o subject to the needle-flame test of Clause The flame shall be applied to the edge of the board where the heatsink effect is lowest when the board is positioned as in normal use. The flame shall not be applied to an edge consisting of broken perforations, unless the edge is less than 3 mm from a OTETIAL IGITIO SOURCE. The test is not carried out if the - RITED BOARD does not carry any potential ignition source; - base material of RITED BOARDS, on which the available power at a connection exceeds 15 VA operating at a voltage exceeding 50 V and equal or less than 400 V (peak) a.c. or d.c. under normal operating conditions, is of flammability category V-1 or better according to AS/ZS , or the RITED BOARDS are protected by an enclosure meeting the flammability category V-0 according to AS/ZS , or made of metal, having openings only for connecting wires which fill the openings completely; or - base material of RITED BOARDS, on which the available power at a connection exceeds 15 VA operating at a voltage exceeding 400 V (peak) a.c. or d.c. under normal operating conditions, and base material of RITED BOARDS supporting spark gaps which provides protection against overvoltages, is of flammability category V-0 according to AS/ZS or the RITED BOARDS are contained in a metal enclosure, having openings only for connecting wires which fill the openings completely. Compliance shall be determined using the smallest thickness of the material. OTE Available power is the maximum power which can be drawn from the supplying circuit through a resistive load whose value is chosen to maximize the power for more than 2 min when the circuit supplied is disconnected For open circuit voltages greater than 4 kv. OTETIAL IGITIO SOURCES with open circuit voltages exceeding 4 kv (peak) a.c. or d.c. under normal operating conditions shall be contained in a FIRE ECLOSURE which shall comply with flammability category V-1 or better according to AS/ZS o voltage exceeds 4 kv.

55 IEC ed. (2001) - age 6 of Report o Annex B After the heading add: For Australia only, this Annex is replaced by the requirements of the Telecommunications Labelling otice issued under the Telecommunications Act. OTE The Telecommunications Act is administered by the Australian Communications Authority. Apparatus not connected to TV circuits. Issue emko

56 IEC ed. (2001) - age 1 of Report o ATTACHMET: MALAYSIA DIFFERECES Test results according to CB BULLETI o. 112A, December 2006 Clause Requirement - Test Result - Remark Verdict Energy Commission circular no.1 year 2003 (no.1/2003) States that a Certificate of Approval is required for manufacturing, selling, Advertising, displaying or importing into Malaysia, electrical/electronic products Listed in Annex A - The supply voltage in Malaysia is 240 Vac, at 50Hz. Rating voltage is V - Class 0 and 01 appliances are not allowed. Class II apparatus. - 13A fused plug-tops shall comply to Malaysian standard (MS 589:art1:1997), if applicable. - 2-pin plug tops shall comply to Malaysian standard (MS 1578:2003) if applicable. o such parts. Should be considered when marketing in Malaysia.

57 CB layout - age 1 of Report o

58 CB layout - age 2 of Report o

59 - age 1 of 9 - hotos Report o Australia plug

60 - age 2 of 9 - hotos Report o China plug

61 - age 3 of 9 - hotos Report o Korea plug

62 - age 4 of 9 - hotos Report o Taiwan plug

63 - age 5 of 9 - hotos Report o United Kingdom or Hong Kong plug

64 - age 6 of 9 - hotos Report o Europe plug

65 - age 7 of 9 - hotos Report o Fixed Japan plug

66 - age 8 of 9 - hotos Report o

67 - age 9 of 9 - hotos Report o

68 Transformer specification - age 1 of Report o Construction / Winding diagram / Component part no: T1

69 Transformer specification - age 2 of Report o Construction / Winding diagram / Component part no: T1

70 Order o age 1 of 12 TEST REORT IEC / E Especially for plug moulded on adaptors roduct ame and address of the applicant ame and address of the manufacturer lug for power adapter Standard sheet I Eastern Frontier Co., Ltd. 13/F., Chung Mei Centre, Block B, 15 Hing Yip Street, Kwun Tong, Kowloon, Hong Kong Same as applicant ame and address of the factories Rating and principal characteristics Trade mark (If any) Model/type Serial no Additional information EASTER FROTIER(SHEZHE)CO.,LTD Factory Bldg #A Hua Fa Road Ind Area Da Lang Village Long Han Shenzhen 2.5A 250VAC Logitech EFS CE Test sample without serial number ower adapter for IT equipment. Tested according to IEC : 3rd. Ed / E 50075:90 art 1: General requirements ame and address of the testing laboratory.o. BOX 73 BLIDER, OSLO, ORWAY Telephone (+47) Fax (+47) Test sample(s) received Tested in period to The test results relate only to the sample(s) tested. Tested by Signature Date Jason Chu ame in block letters Verified by Signature Date Wilson Wang ame in block letters The content of this TRF fully covers the original TRF published by IMQ, dated This form is only for use by EMKO, or by others according to special agreement with EMKO. The completed test report is not valid for external use, unless issued by EMKO or attached to a EMKO certification document. The report shall not be reproduced without written permission from EMKO and may then only be copied in full. EMKO dated 96-01

71 IEC / E Especially for plugs moulded on adapters age 2 of 12 Order o General remarks: Description of equipment under test: Type of accessory: lug moulded on power adapter Standard sheet: Standard Sheet I (E 50075) Copy of marking plate: Throughout this report a comma is used as the decimal separator. ossible test case verdicts: = ass, F = Fail, = ot applicable. laced in the column to the right (Verdict) Tested according to additional information: ational requirements: Other requirements: Additional information: 1) This test report always as an appended report of test report for direct plug in adapter which is made by Eastern Frontier Co., Ltd. 2) Material used refer to list of critical components for details. 3) This a component type plug (interchangeable) all tests were evaluated when installed to the end product. 4) This test report always as an appended report of IEC 60065: Amd 1:2005, report no ame and address production-sites (factories): See page 1 Information about other standards / documents considered: Tested according to national requirements for the following countries: