IEC , 1 Ed. ( ) TESTING AND MEASURING EQUIPMENT/ALLOWED SUBCONTRACTING

Transcription

1 IEC YTEM FOR CONFIRMITY TETING AND COMMITTEE OF TETING LABORATORIE IEC , 1 Ed. ( ) TETING AND MEAURING EQUIPMENT/ALLOWED UBCONTRACTING R = Required to be at Lab = May be subcontracted W = May be witnessed at MTL Measurement/testing Testing / measuring equipment / material needed ubcontracting teady- state voltage and Amp- and voltmeter suitable for the current and waveform, frequency meter current limits Measuring instruments in according IEC 60990: 1999 Figure 4 and ingle pulse limits Oscilloscope Accessibility to electrical Blunt probe of Figure V.3 energy sources and safeguards Thermoplastic parts on Vicat test B 50 of IO 306 which conductive metallic Ball pressure test apparatus according to IEC parts are directly mounted Oven at least 125ºC , Maximum operating Voltage supply ingle phase voltage supply systems/variability/adequacy temperatures for insulating Three phase voltage supply systems materials Temperature (rise) Temperature recorder (multi-channel) Thermocouples Winding resistance (normally > 1,0 W 2-wire, 4-wire <1,0 W ). Voltage Voltmeters (ac/dc) High voltage meter (probe) Current Currents (ac/dc) Loading Loads (resistive) 5.4.2, 5.4.3, Clearances, creepage distance, solid insulation Oscilloscope Dial gauge or caliper Micrometer Pins etc. With different diameters Microscope Impulse test generator circuit 1 of Table D.1. RT

2 IEC YTEM FOR CONFIRMITY TETING AND COMMITTEE OF TETING LABORATORIE Measurement/testing Testing / measuring equipment / material needed ubcontracting Impulse test generator circuit 2 of Table D.1. impulse test generator circuit 3 of Table D.1 RC Test equipment for tracking index per IEC Mandrel (figure 32 to 35), metal foil, equipment suitable for electrical strength test,oads Antenna terminal Insulation resistance meter (500V > 4 MΩ), Impulse test generator circuit 1 of Table D.1 RC insulation Thermal cycling test Full draught oven (± 2ºC) procedure Cooling facility (0º±2 C) Humidity conditioning Chamber RH 93% ± 3%, C Chamber RH 93% ± 3%, 40 C ± 2 C Electrical strength test Test Instrument/equipment according to Figure 36 for electric strength Protection against transient voltages from external circuits Blunt probe figure V eparation between external Non-inductive Resistor 5000Ω, Ampere meter circuits and earth Capacitor discharge Measuring instrument with input impedance 100MW or more in parallel with an input capacitance of 25pF or less Components and parts Force of 10 N ± 1 N that may bridge insulation Resistance of protective High current source with a voltage not exceeding 12 V, conductors and their terminations Determination of the ource with at least 1500A short circuit overcurrent protective device and circuit (Annex R) 5.7 Prospective touch voltage, touch current and proactive conductor current Power source circuit classification Networks in according IEC 60990:1999 figures 4 and 5, Non-inductive Resistor 5000Ω ± 10% Watt meter, variable resistor load, stop watch

3 IEC YTEM FOR CONFIRMITY TETING AND COMMITTEE OF TETING LABORATORIE Measurement/testing Testing / measuring equipment / material needed ubcontracting Top openings and top Cheesecloth bleached cotton cloth 40g/m 2 openings properties Equipment having an electromechanical device for destruction of media Test probe (jointed) of Annex V (figure V.1 and V.2) and wedge probe V.4 Force 45N and 90 N with wedge probe Mechanical enclosure requirements for rotating solid media cale, cylindrical probe / feeler gauge Vernier calliper High pressure lamps Dark sticky mat,, magnified glass with a resolution of 0,1 mm tatic stability for floor Inclined plane 15 standing equipment (Inclined plane 10 ) Force 250N/ Test tool 800Nwith a flat surface 12,5cm by 20cm Glass slide test Glass plate, Horizontal force test Inclined plane 15, force 100N 8.7 Equipment mounted to a wall or ceiling 8.8 Handle strength test method everal weights, timer 75mm width, several weights, scale, timer 8.9 Wheels or casters attachment requirement 8.10 Carts, stands and similar carriers Force 20N, stop watch Force up to 440 N with a circular plan surface Æ 30mm,, stop watch, 8.11 Mounting means for rack mounted equipment everal weights, timer 8.12 Telescoping or rod test tool for applying torque up to 0,6Nm, test tool for applying force 20N, stop watch antennas (Annex 10) 10 Radiations Laser (including laser diodes) everal special equipment for laser classification(iec ) Light emitting diodes (LEDs) everal special equipment for LED classification(iec 62471:2006) X-ray Radiation monitor, ionizing chamber type with an effective area of mm² RV

4 IEC YTEM FOR CONFIRMITY TETING AND COMMITTEE OF TETING LABORATORIE Measurement/testing Testing / measuring equipment / material needed ubcontracting Effect of UV radiation on Test equipment according to IO 178, 179, 180, 527 and materials (Annex C) 8256 and according IO 4892 series. Human exposure to UV radiation (Annex C) Measuring equipment according to IEC Annex B.2.5 Input test Amp-meter suitable for the current and waveform, power meter, voltmeter, Variable loads ignal generator in acc. IEC :1997 RV Annex B.3.2 Covering of ventilation piece of card with 200 g/m² density openings Annex Annex Test conditions for Testing box RA E equipment contain audit ignal generator (sinus) 1kHz or alternative amplifiers Band-pass filter for wide-band noise measurement, pink noise signal generator RA Annex F Durability water/piece of cloth/ timer Annex F Durability Petroleum spirit (85% n-hexane), (CA# ) Annex Alternative test method Cheesecloth (bleached cotton cloth 40g/m 2 ), Wrapping Tissue (12g/ m 2 30g/m 2 ) G.7.3.3; G.8.5.3; G Annex G.9 Mains supply cord Test equipment according IEC Appropriate weights Torque meter or equivalent Annex G.13 IC current limiters resistor: 100 Ω capacitor: 425 μf inductance: 352 mh; 11 Ω dc resistance Oven with a range of -30 C up to 70 C Annex G.14 Test for resistor serving as safeguard Annex G Annex G Annex G.21 Impulse test generator circuit 1 of Table D.1. Impulse test generator circuit 2 of Table D.1. impulse test generator circuit 3 of Table D.1 Test according to IEC Thermal condition Full draught oven (± 2ºC) Abrasion resistance test cratch test device with steel pin Liquid filled components Hydrostatic pressure Hydrostatic pressure test device RT RC

5 IEC YTEM FOR CONFIRMITY TETING AND COMMITTEE OF TETING LABORATORIE Annex Annex J Measurement/testing Testing / measuring equipment / material needed ubcontracting Tubing and fittings Tensile strength test device in acc to IO 527 series compatibility test Vibration test Vibration generator (0,35mm/10Hz-55Hz-10Hz) IEC Insulated winding wires for Test equipment according to IEC ,IEC and IEC use without interleaved insulation Annex M Battery Test to simulate internal faults nail piercing test Wooden board thickness 10mm or more, nail diameter 3mm Annex M.6.2 Leakage current Insulation resistance meter Annex P.2 afeguards against entry uitable tool (or tools) to simulate a straight metal object, 1mm in diameter, length up to 13 of solid foreign objects mm Annex M.8 Protection against internal Equipment according to IEC :2005 ub cl. 6.4 ignition from external spark sources park Test Annex Annex Tests for resistance to Needle flame test apparatus acc. to IEC :2004 heat and fire Distillate fuel oil as described in Annex W flame test apparatus in acc. to IEC :1999 Cheesecloth (bleached cotton cloth 40g/m 2 ), Wrapping Tissue (12g/ m 2 30g/m 2 ) Annex Annex teady force test 10N ± 1N T.2 - T.4 Test finger (figure V1 or V2 unjointed, 30N± 3N) Test tool 100N± 10N with a circular plan surface Æ 30mm cale up 18 kg, top watch Annex T.5 teady force test, 250 N Test tool 250N± 10N with a circular plan surface Æ 30mm. Annex T.6 Enclosure impact test Æ 50mm/500g± 25g steel ball Annex T.7 Drop test Hard wood 13mm on 18mm ± 2mm plywood, two layers. ruler up to 1000 mm ± 10mm AnnexT.8 tress relief test Measuring equipment according to IEC or Oven 70K over normal temp. Annex T.9 Glass breakage steel ball 50mm, approx 500g., Fragmentation test Centre punch and a square of 50 mm side Annex U Mechanical strength of CRTs and protection against the effects of implosion Test equipment acc.iec cale, diamond stylus, cooling liquid, timer

6 IEC YTEM FOR CONFIRMITY TETING AND COMMITTEE OF TETING LABORATORIE AnnexV.1.6 Measurement/testing Testing / measuring equipment / material needed ubcontracting Test method 5 Terminals intended to be used by an ordinary person Force 1 N ± 0,1N Terminal probe IEC 61032:1997 figure 4 Note: The presence of equipment alone does not indicate a satisfactory situation. Assessors must evaluate the equipment design, calibration, uncertainty and documentation to ensure compliance with the directions of the standard. The requirements of IO/IEC regarding validation are applicable, as the tests of this standard are not standardised tests. IEC equipment has been sub-grouped into: -'RA' = 'Required for audio'; in addition to '', required for testing apparatus with audio amplifiers (audio power >0,5 W) - = Required Basic ; test and measurement equipment required for all equipment - RC = Required for antenna ; in addition to, required for testing equipment with connection(s) to a cable distribution system - RT = Required for telecom ; in addition to, required for testing apparatus with connection(s) to a telecommunication network. - RV = Required for CRT / Plasma/LCD in addition to required for testing CRT Cathode ray Tubes/ picture tubes or plasma/lcd