AA Portable Power Corp 825 S 19th Street, Richmond, CA
|
|
- Ashlee Dickerson
- 10 months ago
- Views:
Transcription
1 Specification Product name: Cylindrical lithium-ion Iron Phosphate battery Model No.: 38120L/S Specifications: 10000mAh/3.2V
2 1. Range of application: This specifications is applied to 38120L/38120S lifepo4 batteries 2. Product name and models: 2.1 Name: Cylindrical lifepo4 battery 2.2 Model: HW 38120L/S 3. Specifications: NO. ITEM Specifications 3-1 Nominal Capacity: 10000mAh 3-2 Rated voltage 3.2V 3-3 Energy density (Wh/kg) Internal Resistance 8mΩ 3-5 Charge (CC-CV) Charged with constant current to 3.65v and then charged with constant voltage to A 3-6 Charge (float) 3.6V 3-7 Max. charging current 3C(30A) 3-8 Standard. charging voltage 3.65±0.05V 3-9 Recommended charging current 0.5C, 5A 2hours 3-10 Max. continuous discharging current 3C (30A)-10C(100A) 3-11 Max.pulse discharging current(30seconds) 10C(100A) Recommended discharging current 1C(10A) 3-12 Max. End-off discharged voltage 2.0V 3-13 Self discharge rate (monthly) 2-3% 3-14 Dimensions (mm) Diameter 38±1 Height 38120L:122±1; 38120S:132± Weight (Approx.) 38120L:300g; 38120S: 330g 3-16 Working temperature Charging 0~45 Discharging -20~ Storage temperature In one month -20~45 In six months -20~35 *The battery shall be in the state of half fully charged or with the voltage of 3.2~3.3V during storage and transportations.
3 The cycle life testing curve and discharging and charging curve at 1C of Ah cell(x line means the cycles, the Y line means the capacity) X line means the time in minutes, Left Y line means Voltage, Right Y line means the capacity.
4 Discharging curve at 1C,2C and 3C Discharging curve at 5C
5 Discharging curve at 10C 4.Test conditions 4.1 The experiments and survey should be on the nominal temperature of 20±5, and the nominal humidity should be 65±20%. Standard charging: first charged by constant current of 0.5C, then by constant voltage up to 3.65v, and when the current falls down to 200mA, then stop the charging. Standard discharging: discharging at constant current of 5000mA until the voltage falls down to 2.0V. 4.2 The testing facilities: Voltmeter: Impedance >1000Ω /piece; Ammeter Total resistance <0.01Ω ; Vernier Caliper: Precision: 0.02mm;
6 5. Testing 5.1 Appearance The surface should be clean, no mechanical damage, adherent point should be no rust, and there should be necessary marks on the cells. 5.2 Characteristics Item Test program Standard Open-circuit voltage After standard charging,then measure the open-circuit voltage in one hour. 3.3V Nominal capacity Discharging by constant current of 0.5C in one hour Capacity 10Ah until the voltage falls down to 2.0V Cycle life At the temperature of 25±5, charged by constant 2000times current of 0.5C until the voltage comes up to 3.65V, then charged by constant voltage of 3.65v until the current falls down to 200mA, then kept aside for 0.5-1hour, then discharged of 0.5C until the voltage falls down to 2.0V, then kept aside for another 0.5-1hour, then stepped into the next cycle. If the capacity falls down 7000mAh for two continuous cycles, then it is considered as dead Reserve ability of the capacity After standard charging and storage at 25±5 for 28days, then discharging at 0.5C to the voltage of 2.0V, the reserved capacity is 90% nominal capacity. Capacity 9Ah High Temperature performances Low temperature performances After standard charging and storage at 60±2 for 4 hours, then discharging at 0.5C to voltage of 2.0V, the reserved capacity is 90% nominal capacity. After standard charging and storage at -10±2 for 4 hours, then discharging at 0.5C to the voltage of 2.0V, the reserved capacity 60% nominal capacity Extrusion Put the battery into the two planes of the extrusion equipment, boost pressure to 13KN, keep the pressure for 1 min. the vertical axis should parallels to the horizontal plane of the extrusion equipment, be vertical to the direction of extrusion, each battery only accept one test Thermal shock After putting the battery into the incubator, the temperature should be increased continuously at the rate of 5 ±2 /min to 130 and kept for 30 min, then take out the battery, resume to the room temperature. Capacity 9Ah Capacity 6Ah The battery must be no fire, no
7 5.2.9Overcharged The test is made at temperature of 20 ±5. The battery should be discharged at I 5 A until the voltage is 2.0V, put the battery into ventilation cabinet, connecting the anode and cathode to the DC power supply. Change the output current of power supply to 15I 5 A, The voltage should not be lower than 10V, charging for 7 h or and the voltage stays the same, until the current falls down to Forced discharge The test is made at temperature of 20 ±5. Discharged at I 5 A until the voltage falls down to 2.0V, then reverse charged at 5I 5 A current for 90 min Short circuit After standard charging fully, put a battery which is connected with thermocouple (The essential resistance of the circuit should be less than 50mΩ ), short circuit for the anode and cathode, monitoring the temperature of the battery, when the battery temperature falls with a range of 10, then stop the testing Acupuncture The test is required to operating at the temperature of 20 ±5. Standard charged to the voltage of 3.65V, Put the battery in which is connected with thermocouple into the ventilation cabinet, pricked with a diameter-3mm stainless steel picker throughout the centre of the of the battery at most surface in 20mm/s~40mm/s speed, and keep 1min Heavy Impact Put the battery on the floor, put a Φ 15.8mm Steel column into center of the battery, the vertical axis of the Steel column should be parallel to the floor, then let the 9.1kg s heavy object fall on to the steel column from a height of 610mm Vibration After standard charging fully, put the battery on the vibration table of vibrating frequency of 10Hz-30Hz, and continuously vibrated from X,Y,Z three directions with 10Hz-50Hz for 30mintues, and the speed is 1oct/min The battery must be no fire and no explosion There is no damage of the appearance and no smoking, no penetration, no explode, and the voltage is no less than 3.2V
8 5.2.15Collision After vibration test, fix the battery from X,Y,Z three perpendicularity and colliding pulse at 100m/s2, and 40~80times per min,and each pulse collisions keeps 16ms and 1000±10 times Free fall drop After standard charging fully, let the battery fall from a height of 1m from X,Y,Z six directions accordingly to the hard wood with thickness of 18-20mm on the cement floor, each for each direction, and then discharged at 1C until the voltage is 2V, then charging and discharging them no less than 3cycles StorageCharacteristics Battery shall be charged continuously at a constant current of 0.5C until the voltage is up to 3.65v, then charged at the constant voltage of 3.65v until the capacity falls down to 0.02c; and stored under the condition of normal temperature of 20 ±5 for 30days; After 30-days storage, discharge the battery continuously at the constant current of 0.5C to the end-off voltage of 2.0V There is no damage of the appearance and no smoking, no penetration, no explode, and the voltage is no less than 3.2V No fire, no explode, and the discharging time is no less than 51minutes Remaining capacity 9Ah
9 6. Matters need attention. 6.1 Don t put the battery near the origin of heat, such as fire, heater etc. 6.2 Please use the matched charger to charge the battery. 6.3 Don t convert the anode and cathode. 6.4 There are safety features in the battery, in order to keep safe, do not dissect or change the structure of the battery. 6.5 It is forbidden to connect the anode and cathode directly with metal. 6.6 It is forbidden to pound, throw, trample the batteries. 6.7 It is forbidden to put the battery into the water, or in the moisture place. 6.8 If the battery are stored without being used for 6 months, we recommend the batteries fully charged before using them. 7. Shelf life 7.1 The shelf life is 24 months since the production time. 7.2 Our company is not responsible for quality inferiority or accidents caused by abuse operating or using which are not compliant with the specifications and instructions. 8. Transportation During the transportation, preventing the strenuous vibration, impact, exposed to the sun and rain, and keep the battery on a state of half-charged. 9. Dimension
AA Portable Power Corp
1. Range of application: This specification is applied to lifepo4 40152SE batteries. 2. Product name and models: 2.1 Name: Cylindrical lifepo4 battery 2.2 Model: LFP-40152SE 3. Specifications: NO. ITEM
Lithium-ion Battery DATA SHEET
Lithium-ion Battery DATA SHEET Battery Model: LIR17500 Prepared Authorized Approved Manufacturer: EEMB Co., Ltd. Website: http://eemb.com This Specification describes the requirements of the lithium ion
Product Specification
Specification No. Polymer Lithium-ion attery Model:PL-4545125-10C AA Portable Power Corp (http://www.batteryspace.com) Address: 860 S, 19 th St, Unit A, Richmond, CA, 94804 Tel: 510-525-2328 Fax: 510-439-2808
Product Specification Polymer Li-ion 7.4v 2100 mah
Polymer Lithium-ion attery Product Specification Polymer Li-ion 7.4v 2100 mah (For high discharge ratio battery) 2700 Rydin Road, Unit C Richmond, CA, 94804, USA Tel: 510-252-2328 Fax:510-439-2808 All
EEMB CO., LTD. Specification
ZJQM-RD-SPC-A0994 0.0 2015-8-6 1/8 EEMB CO., LTD Li-ion Battery Model: Capacity: 2200mAh Prepared Checked Approved Customer: Customer Approval(Customer confirmation): Signature Checked Approved Address:Room
Lithium-ion Battery DATA SHEET
Lithium-ion Battery DATA SHEET Battery Model: LIR18650 Prepared Authorized Approved UL Certified MH20555 Manufacturer: EEMB Co., Ltd. Website: http://eemb.com This Specification describes the requirements
Li-ion Cylindrical Battery Specification
Li-ion Cylindrical Battery Specification MODEL: EC- 265HC Nominal Capacity: 5200 mah page 1 of 10 Content 2.Scope... 3 3. Initial Dimension... 3 4.Specification... 4 5 General Performance... 5 6 Environment
PRODUCT DATASHEET. is brought to you by. SOS electronic distribution of electronic components
PRODUCT DATASHEET is brought to you by SOS electronic distribution of electronic components Click to view availability, pricing and lifecycle information. Visit https://www.soselectronic.com/ Datasheet
Lithium Ion Battery Specifications
1 Lithium Ion Battery Specifications Type: Normal Cylindrical Battery Model: LC-14500 AA Portable Power Corp Dba BatterySpace.com 825 S 19 th Street, Richmond, CA 94804 Tel: 510-525-2328 Email: sales@batteryspace.com
EEMB CO., LTD. Specification
ZJQM-RD-SPC-A0370 0.0 2014-11-5 1/7 EEMB CO., LTD Polymer Li-ion Battery Model: Capacity: 1450mAh Prepared Checked Approved Customer: Customer Approval(Customer confirmation): Signature Checked Approved
ENGLISH. Datasheet. Polymer Li-ion Rechargeable Battery Pack
ENGLISH Datasheet Polymer Li-ion Rechargeable Battery Pack 1. Scope This specification shall be applied to polymer Li-ion Rechargeable Battery manufactured by RS Component. 2. Basic Product Characteristics
Specification Approval Sheet. signed by client. signed by manufacturer
Specification Approval Sheet Customer : Mikroe Model : SR674361P Type : Li-polymer battery Specification: 3.7V/2000mAh signed by client Confirmed Checked Approved signed by manufacturer Prepared : He lu
EEMB CO., LTD. Specification
EEMB CO., LTD Lithium Thionyl Chloride Battery Specification Energy Type Model: Capacity: ER14250 1200mAh Prepared Checked Approved Customer: Customer Approval (Customer confirmation): Signature Checked
Lithium-ion Polymer Battery Specification
Version:A/0 Issuance date: 2012-03-12 Lithium-ion Polymer Battery Specification Model: JA-0545135P Draft Examine Approve J & A ELECTRONICS (CHINA) CO., LTD. Tel: +86(752)216 3772 Fax: +86(752)216 3772
LITHIUM / THIONYL CHLORIDE High Power Type ER18505M BRIEF SPECIFICATION
LITHIUM / THIONYL CHLORIDE High Power Type ER18505M BRIEF SPECIFICATION Model: ER18505M Spirally Wound Type Nominal Voltage: 3.6V Nominal Capacity: 3.2Ah Weight: 30g Stainless steel container with PVC
Rechargeable Lithium Ion Battery Model : ICR18650 A2
1 (7) Rechargeable Lithium Ion Battery Model : ICR18650 A2 Revision History REVISION DATE ORIGINATOR REASON FOR CHANGE 0 2003-06-11 Yun, In Taeg Original Release Prepared Reviewed Yun, In Taeg Jung, Jae
Specification Approval Sheet
Name: Lithium Polymer Battery Model: 505396 SPEC: Number: 3.7V/2300mAh YKZ0809050622Y Approved By Checkup Make Signature Date Customer Company Name: Confirmation Stamp: Add: YOKU Industrial Zone Nangjing
No Q/LX.S.E Edition A/0. Expocell Group, Inc. Cylindrical Li/MnO 2 Battery. Specification. Battery Type: CR123A(CR17345) Customer.
No Q/LX.S.E.08.005-2007 Cylindrical Li/MnO 2 Battery Specification Battery Type: Customer Date 1 9 1.Purpose 1.1 In order to avoid errors and deviations by different testing method or condition, we established
LITHIUM THIONYL CHLORIDE Computer Back-up Type ER14250-CB BRIEF SPECIFICATION
LITHIUM THIONYL CHLORIDE Computer Back-up Type ER14250-CB BRIEF SPECIFICATION Model: ER14250 (1/2AA Size) Bobbin Type Nominal Voltage: 3.6V Nominal Capacity: 1.2Ah Weight: About 13g ISO9001 Certified UL
Specification Approval Sheet
Page No. 1/11 Specification Approval Sheet Model:IFR18650EC-1.5Ah Prepared By/Date(RD) Reviewed by/date Checked By/Date (QA) Approved By/Date Bing Zeng/2012.4.26 Wu Chen/2012.4.26 SiBiao Jin/2012.4.26
Lithium-ion Rechargeable Battery Pack. Specification. Product Name: LiFePO4 Battery Pack. Product Specification: 48V 210Ah Dch 6 Kw (10080Wh)
Doc no 180 Rev: 01 of 09 Date: 28/09/2016_ Lithium-ion Rechargeable Battery Pack Specification Product Name: LiFePO4 Battery Pack Product Specification: 48V 210Ah Dch 6 Kw (10080Wh) Doc no _180 Rev: 02
EEMB CO., LTD. Lithium Thionyl Chloride Battery Specification. High Power Type. Prepared Checked Approved. Signature Checked Approved
EEMB CO., LTD Lithium Thionyl Chloride Battery Specification High Power Type Model: Capacity: ER26500M 6.5Ah Prepared Checked Approved Customer: Customer Approval (Customer confirmation): Signature Checked
Specification Approval Sheet
. Specification Approval Sheet FOR LIPO BATTERY Product Name Model SPEC Company Name Document Number Li-ion Polymer Battery 6567100/4000mAh/3.7V GMB POWER GMB1102150902 Sample Number Document Revision
Specification Approval Sheet
Specification Approval Sheet Name:Polymer Lithium-Ion Battery Model: CELLEVIA BATTERIES LP601730 SPEC:3.7V/ 250mAh Number: 601730 Specification Modification Records Modification Time Descriptions Issued
Lithium-ion Battery DATA SHEET
Lithium-ion Battery DATA SHEET Battery Model: LIR18650 Prepared Authorized Approved Manufacturer: EEMB Co., Ltd. Website: http://eemb.com This Specification describes the requirements of the lithium ion
Silver Oxide Button Cell 303F
Model No:303F Page 1 of 7 1 Scope The specification is applicable to the Vinnic brand (Mercury free) supplied by CHUNG PAK BATTERY WORKS LTD. 2 Kind of Products Specified Name (Designation): 303F IEC Designation:
Zinc Chloride Dry Battery SUM3/SUPER/G
Model No:SUM3/SUPER/G Page 1 of 8 1. Scope This specification is applicable to the VINNIC brand Zinc Chloride Mercury Free and No Lead Added Dry Batteries supplied by CHUNG PAK BATTERY WORKS, LTD. 2. Technical
Li-ion Rechargeable Button Cell. Specification
Customer: Specification Model: LIR2032 Prepared By/Date Checked By/Date Approved By/Date Note:1.Kindly please sign on the above and send it back to us if the sample is approved. 2.Kindly please contact
RED CHARGER FOR RED BRICK V-LOCK LITHIUM ION BATTERIES OPERATING MANUAL
RED CHARGER FOR RED BRICK V-LOCK LITHIUM ION BATTERIES OPERATING MANUAL Please read these instructions concerning your safety The RED CHARGER lithium-ion battery charger has been designed to manage relatively
CATALOG. <Japanese> <English>
CATALOG About delivery style, consult the sales representative. About the minimum order quantity, consult the sales representative. Product specification and appearance are subject to change for improvement.
Lithium-ion Polymer Battery Specification
Version:A/0 Issuance date: 2017-01-16 Lithium-ion Polymer Battery Specification Model: JA-602025P Draft Examine Approve J & A ELECTRONICS (CHINA) CO., LTD. Tel: +86(755)81678350 Fax: +86(755)27291362 Customer:
Data Sheet BP v 100Ah LiFePO 4 (Peli TM Case Kit)
Data Sheet BP2589-12v 100Ah LiFePO 4 (Peli TM Case Kit) Product Name Battery Model Spec File Revision LiFePO4 Battery in Peli TM Case LiFePO4-11198141 4S5P 12.8V 100Ah A2 Amendment Records Revision Description
GWL/ Power Group Technology Solutions Stay Powered for the Future
GWL/ Power Group Technology Solutions Stay Powered for the Future GWL/Power Specification Document LiFePO4 Batteries with PCM 6V and 12V models Technical Specifications April 2012 http://www.ev-power.eu
Title Specifications of Lithium Ion battery (Cylindrical Type) page 1/12
Title Specifications of Lithium Ion battery (Cylindrical Type) page 1/12 1. Extent of the application This specification is applied to the SANYO Lithium Ion Battery of the above mentioned type for a Notebook
Lithium-Ion CYCLIC BATTERIES. Applications. LITHIUM-ION BATTERIES. LiFePO4 BATTERY CELLS. Only benefits. Advantages. Li-Ion
CYCLIC BATTERIES Li-Ion LITHIUM-ION BATTERIES Lithium-Ion Only benefits Advantages. LiFePO4 BATTERY CELLS - Excellent low temperature performance - High safety performance - Longer lifespan - High energy
EV Power - Battery Control Unit Instructions. 8 Cell 24V
EV Power - Battery Control Unit Instructions. 8 Cell 24V PAGE 1 OF 12 BCU-EVPPAK Features - Simple to install and use, microprocessor control. - Low power requirement, just 15mA when switched on with relay
Duracell Battery Glossary
Duracell Battery Glossary 1 Duracell Battery Glossary AB Absorption Alloy Ambient Humidity Ambient Temperature Ampere-Hour Capacity Anode Battery or Pack Bobbin C-Rate (also see Hourly Rate) Capacity Capacity
DC Electronic Loads simulate NTC devices for temperature monitoring in battery test applications
DC Electronic Loads simulate NTC devices for temperature monitoring in battery test applications This application note discusses the use of programmable DC loads to simulate temperature sensors used in
Lithium Ion Batteries - for vehicles and other applications
Lithium Ion Batteries - for vehicles and other applications Tekes 2008-12-03 Kai Vuorilehto / European Batteries What do we need? High energy (Wh/kg) driving a car for 5 hours High power (W/kg) accelerating
RS Stock number
RS Stock number 617-0773 Description: For general purpose applications No memory effect Note: All batteries are supplied with only a residual charge and should be charged at the continuous charge rate
IEC 62133:2012 (2nd Edition) Understanding IEC Safety Requirements for Rechargeable Cells & Batteries used in Portable Devices
Battery Standards Whitepaper September 2015 IEC 62133:2012 (2nd Edition) Understanding IEC Safety Requirements for Rechargeable Cells & Batteries used in Portable Devices Guide to IEC 62133:2012 (2nd Edition)
Duo Battery Charge Controller
Duo Battery Charge Controller RENOGY 10A 20A Pulse Width Modulation Solar Charge Controller Manual 1 2775 E. Philadelphia St., Ontario CA 91761 1-800-330-8678 Version: 1.2 Important Safety Instructions
STANDARD SPECIFICATION. Medium Prismatic Lithium-Ion Rechargeable Battery. Model 1s1p MP Lithium Product Manager. Technical Director
STANDARD SPECIFICATION Medium Prismatic Lithium-Ion Rechargeable Battery Model 1s1p MP 144350 Name Position Date Signature Written by A. Kerouanton Lithium Product Manager 10/05 Checked by O. Girard Technical
GV-Boost Manual. 8A Input / W IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS. Solar Charge Controllers with Maximum Power Point Tracking
GV-Boost Manual Solar Charge Controllers with Maximum Power Point Tracking For models: GVB-8-Pb-12V: GVB-8-Pb-24V: GVB-8-Pb-36V: GVB-8-Pb-48V: GVB-8-Li-**.*V: 12V Lead-Acid/AGM/Gel/Sealed/Flooded 24V Lead-Acid/AGM/Gel/Sealed/Flooded
Research Progress of Advanced Lithium Ion Polymer Battery Technology
The 34 th Florida International Battery Seminar Research Progress of Advanced Lithium Ion Polymer Battery Technology Peter Cheng Highpower Research Institute ----------------------------------------------------March
(The information contained in this document is for reference only and should not be used as a basis for product guarantee or warranty.
Technical Specification for Professional Camcorder of Ni-MH Rechargeable Battery Pack Product Description Product No. Model No. : 12.0V Ni-MH, 4000mAh Camcorder Battery Pack : VMH9011 : Replace Sony NP-1B,
Cylindrical Primary Lithium Handbook and Application Manual
: Energizer lithium iron disulfide differs from alkaline batteries in chemistry and construction. They are built in a spiral construction featuring two long, thin electrodes rolled together to form a jellyroll
LFP(12-16 ( CE
User Manual of Universal Smart Charger (18A, 29.6V-58.4V Cut-Off) for 36V- 48V SLA, 29.6V-51.8V Li-Ion/LiMnNi (8-14 Cells),38.4V- 51.2V LFP(12-16 Cells) -- CE listed AA Portable Power Corp (http://www.batteryspace.com)
A Structure of Cylindrical Lithium-ion Batteries
Introduction A Structure of Cylindrical Lithium-ion Batteries A lithium-ion battery is an energy storage device providing electrical energy by using chemical reactions. A few types of lithium-ion battery
Development of a Smart High-power Battery for CubeSats
Development of a Smart High-power Battery for CubeSats David J. Wright & Andrew E. Kalman Pumpkin, Inc. Slide 1 Desirable Features Better estimate of battery capacity, to include aging effects Panasonic
HENAN NEW TAIHANG POWER SOURCE CO.,LTD (STATE-OWNED FACTORY NO.755)
Nickel-iron Storage Battery Operation & maintenance manual HENAN NEW TAIHANG POWER SOURCE CO.,LTD (STATE-OWNED FACTORY NO.755) 1 PREFACE The nickel-iron storage battery has a nickel oxide-hydroxide anode
Battery Box. Let Thunder power your weekend escape! Watch us on. Scan code to see Thunder in action. facebook.com/thunderaccessories
Battery Box Let Thunder power your weekend escape! Watch us on facebook.com/thunderaccessories Scan code to see Thunder in action THE THUNDER DIFFERENCE Thunder helps take you places you ve never been
BlueSolar charge controller MPPT 100/30
Manual EN Handleiding NL Manuel FR Anleitung DE Manual ES Användarhandbok SE Appendix BlueSolar charge controller MPPT 100/30 1. General Description 1.1 Charge current up to 30 A and PV voltage up to 100
ME310B BATTERY POWERED CRIMP TOOL
Description The ME310B Battery Powered Crimp Tool is a hand held, self contained crimp tool intended to crimp machined contacts onto copper and aluminum cable. KEEP THIS MANUAL Important Safety Information
Lithium Battery UN38.3 Test Report
报告编号 (Report ID): 0907034-058-1 锂电池 UN38.3 测试报告 Lithium Battery UN38.3 Test Report 样品名称 (Sample Description) Lithium ion battery 委托单位 ( Applicant ) Shandong Real Force Enterprises Co.,Ltd 生产单位 ( Manufacturer
COMPACT BUT CUT OFF DC POWER CURRENT, POWER CAPSULE CONTACT RELAY
COMPACT BUT CUT OFF DC POWER CURRENT, POWER CAPSULE CONTACT RELAY EB RELAYS (AEB) (1A type) FEATURES Compact and high capacity using double contacts in series and permanent magnet installed. (1,A/3 times)
APPROVAL SHEET FOR TIDECTX2 BATTERY
Model No. : Specification: 3.7V/ 570mAh APPROVAL SHEET FOR BATTERY Total No. of Pages: Total 13 pages including this cover sheet Approved by Section written checked Issues Name Approve Presented by Section
All About Batteries. Created by lady ada. Last updated on :22:29 PM UTC
All About Batteries Created by lady ada Last updated on 2018-01-04 09:22:29 PM UTC Guide Contents Guide Contents Overview How Batteries Are Measured Power Capacity and Power Capability Lead Acid Batteries
HXE4B BATTERY POWERED CRIMP TOOL
Description The HXE4B Battery Powered Crimp Tool is a hand held, self contained crimp tool intended to crimp copper and aluminum cable with DMC Y dies. Safety Safety is essential in the use and maintenance
Batteries and more. Powered by (CE, UL & ISO9001 APPROVAL)
Batteries and more Powered by (CE, UL & ISO9001 APPROVAL) 1. Feature 1) Maintenance free-operation. There is no need to check the special gravity of the electrolyte or to add water during the service life.
Maximum output power with circulator Wo 6 kw. Maximum output power without circulator Wo 5 kw
Packaged, metal-ceramic, water cooled continuouswave magnetron with integral RF cathode filter intended for use in industrial microwave heating applications. The tube features a quick- heating cathode,
Document: PRODSPEC-140 Revision: G DCN No Date: October 1, 2014 Product: 10-amp EnerGenius NRG Battery Charger
Document: PRODSPEC-140 Revision: G DCN No. 106512 Date: October 1, 2014 Product: 10-amp EnerGenius NRG Battery Charger 1. GENERAL DESCRIPTION 1.1 General Description Fully regulated, constant voltage,
Lithium-Ion CYCLIC BATTERIES. Applications LITHIUM-ION BATTERIES. LiFePO4 BATTERY CELLS. Only benefits. Advantages BATTERY SUPPLIES.BE.
CYCLIC BATTERIES Li-Ion LITHIUM-ION BATTERIES Lithium-Ion Only benefits Advantages LiFePO4 BATTERY CELLS - Excellent low temperature performance - High safety performance - Longer lifespan - High energy
State-of-Charge (SOC) governed fast charging method for lithium based batteries. Fahmida Naznin M/s. TVS Motor Company Ltd.
State-of-Charge (SOC) governed fast charging method for lithium based batteries Fahmida Naznin M/s. TVS Motor Company Ltd. Hosur, Tamilnadu Hybrid technology & battery requirement References: 1. Battery
MODEL 6010A 6 12 VOLT BATTERY CHARGER ASSOCIATE
MODEL 600A 6 VOLT BATTERY CHARGER ASSOCIATE IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This manual contains important safety and operating instructions for the battery charger you have purchased.
Lithium Manganese Dioxide Battery (Li/MnO2)
LITHIUM MANGANESE DIOXIDE BATTEY Lithium Manganese Dioxide (Li/MnO2) Primary Safety Instructions This battery contains lithium, organic solvents, and other combustible materials. For this reason, improper
ABOT4001 REV1 BATTERY POWERED CRIMP TOOL
Figure 1 Description The ABOT4001 rev1 is a handheld Battery Powered Crimp tool. It uses dies engineered to meet the requirements of the AS22520/40-01 and is intended to crimp insulated terminals, splices,
Tadiran Lithium Batteries. Product Data Catalogue
Tadiran Lithium Batteries Product Data Catalogue Customized battery packs The design and assembly of battery packs require special skills, expertise and experience. Therefore it is not recommended that
EVS RP6020. Instruction Manual
Instruction Manual TDK Lambda BEFORE USING THE PRODUCT Be sure to read this instruction manual thoroughly before using this product. Pay attention to all cautions and warnings before using this product.
II Technical Target. HF/PFC 1.5KW Lithium Battery Charger
HF/PFC 1.5KW Lithium Battery Charger Models Size(mm):348(L) 180(W) 140(H) N.W. (kg):6.33 HF/PFC On-board Charger (Lithium Battery Charger) I Product Summary & Application Scopes The charger is applicable
SPEC. NO. KL24H95x.XXX/ KL24HS95x.XXX Series ISSUE DATE
DESCRIPTION Lithium Ion Battery For E-bike EDITION B PAGE 1/10 1. Applicability The specification is applicable to Mondia Lithium Ion Rechargeable batteries 1.1 Product code KLxxHyyz.nnn E-bike Battery
Wireless Sensors in Buildings
Wireless Sensors in Buildings Energy Harvesting, London 12 th March 2014 An EPSRC Funded Network Gilles Chabanis Schneider Electric at a glance The global specialist in energy management Large company
Installation Guide The RSi brief overview:
Electronic Rust Protection Installation Guide The RSi brief overview: The RustStop RSi Industrial uses a 6 channel output system to drive up to 18 anodes (Rust Magnets ) Each channel has its own output
Turquoise Stroke Switches
Long Stroke and Sliding Contact Construction Sealed Switches Turquoise Stroke Switches 13.3 10.1 (Unit: mm) RoHS compliant FEATURES For pin plunger, it maintains a long stroke OT (Over Travel) with over
UBI-2590 HC SMBus (Part No. UBBL13) Battery Specification
UBI-2590 HC SMBus (Part No. UBBL13) Battery Specification Copyright Copyright 2012, Ultralife Corporation. All Rights Reserved. Trademark Information Ultralife, the Ultralife logo design, SmartCircuit
PowerSafe OPzV Operation Guide for Solar Applications
Sustainable solutions PowerSafe OPzV Operation Guide for Solar Applications Operation Guide > PowerSafe OPzV < 2 Safety precautions Batteries give off explosive gasses. They are filled with dilute sulphuric
SAFETY OF RELiON LITHIUM IRON PHOSPHATE (LiFePO 4 ) BATTERIES
SAFETY OF RELiON LITHIUM IRON PHOSPHATE ( ) BATTERIES I. Introduction The news media, internet and battery marketplace is filled with misinformation regarding the safety of lithium batteries. RELiON has
THINERGY MEC220. Solid-State, Flexible, Rechargeable Thin-Film Micro-Energy Cell
THINERGY MEC220 Solid-State, Flexible, Rechargeable Thin-Film Micro-Energy Cell DS1013 v1.1 Preliminary Product Data Sheet Features Thin Form Factor 170 µm Thick Capacity options up to 400 µah All Solid-State
1.5KW HF/PFC Lithium Battery Charger. 2KW HF/PFC Lithium Battery Charger
1.5KW HF/PFC Lithium Battery Charger Size (mm):348(l) 180(W) 140(H) TCCH-H35-40 34.6V 40A TCCH-H51-33 51.1V 33A TCCH-H65-25 65V 25A TCCH-H90-20 89.8V 20A TCCH-H104-16 104V 16A TCCH-H114-14 114V 14A TCCH-H130-12
I t n e t l e l l i l g i e g n e t n So S l o a l r a Ch C a h r a g r e g Co C n o t n r t o r l o l l e l r U e s r e s Man an al
1 Intelligent Solar Charge Controller User s Manual Please read this manual carefully before you use this product. 2 3 Catalogue 1. Product Introduction.4 2. Installation..5 3. Operation 6 4. Common Fault
CAM-7 /LTO Lithium-Ion Cells for Logistically Robust, Damage-Tolerant Batteries
CAM-7 /LTO Lithium-Ion Cells for Logistically Robust, Damage-Tolerant Batteries David Ofer, Daniel Kaplan, Mark Menard, Celine Yang, Sharon Dalton-Castor, Chris McCoy, Brian Barnett, and Suresh Sriramulu
Super PWRgate PG40S Spring City Drive Waukesha, WI
Super PWRgate PG40S www.westmountainradio.com 1020 Spring City Drive Waukesha, WI 53186 262-522-6503 sales@westmountainradio.com 2015, All rights reserved. All trademarks are the property of their respective
SDM320D / SDM320A. Single phase din rail meter SDM320D / SDM320A user manual
SDM320D / SDM320A DIN Rail Single Phase Two Wire Energy Meter with S0 Pulse Output (Four modular) User Manual ------------------- 1.1 Safety instruction 1.2 Introductions 1.3 Performance criteria 1.4 Specifications
Safe lithium ion high energy batteries. for electric propulsion. Chargers, on board supply EN LiFePO4
Safe lithium ion high energy batteries for electric propulsion Chargers, on board supply EN 3-2016 LiFePO4 LiFePO4 aquawatt lithium batteries are made with advanced lithium iron phosphate cells. These
Large Format Lithium Power Cells for Demanding Hybrid Applications
Large Format Lithium Power Cells for Demanding Hybrid Applications Adam J. Hunt Manager of Government Programs 2011 Joint Service Power Expo Power to Sustain Warfighter Dominance Myrtle Beach, SC May 4,
AC/DC LIPO CHARGER INSTRUCTION MANUAL
DTXP4195 AC/DC LIPO CHARGER INSTRUCTION MANUAL The Onyx 150 AC/DC LiPo balancing charger is the perfect entry-level LiPo charger for modelers using up to 3S LiPo batteries. Inexpensive and very easy to
Technical Manual. E-trek DM Series SHANDONG SACREDSUN POWER SOURCES CO.,LTD
Technical Manual E-trek DM Series Version:V3.0 SHANDONG SACREDSUN POWER SOURCES CO.,LTD Security Instruction Please read these instructions carefully in order to make correct, safe, and effective operation.
Models: SP3, SPSS3 Automatic Battery Charger
OWNERS MANUAL Models: SP3, SPSS3 Automatic Battery Charger PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE. This manual will explain how to use the charger safely and effectively. Please read and
PB-600 Instruction Manual
PB600 Instruction Manual PB600 Instruction Manual Index 0.Product description... 1 1.Notes on operation... 1 2.Front and back panel... 1 3.Derating curve... 2 3.1 Charging current VS temperature... 2 3.2
ISSUED 10/31/2011 Energy Company Panasonic Corporation E-013 SPECIFICATION VANADIUM LITHIUM RECHARGEABLE BATTERY VL-2020/VCN VL2020.
Control number 2011-10E-013 To FARNELL Ordering Code Model Code SPECIFICATION VANADIUM LITHIUM RECHARGEABLE BATTERY : : VL-2020/VCN VL2020 Approved by Division/Department Name Title Signature/date ISSUED
USER MANUAL 12V 4.3A 5 YEAR WARRANTY. FOR ALL 12V TYPES OF LiFePO 4 BATTERIES FULLY AUTOMATIC
USER MANUAL CTEK BATTERY CHARGER LITHIUM US 5 YEAR WARRANTY FOR ALL 12V TYPES OF LiFePO 4 BATTERIES FULLY AUTOMATIC 12V 4.3A 1. Connect the charger to the battery! 1. Brancher le chargeur à la batterie!
NI-MH LOW-SELF DISCHARGE READY TO USE
Product Datasheet NI-MH LOW-SELF DISCHARGE READY TO USE RS Article No.: 9053781 1. Scope of Application: Type Nominal Voltage 1.2V/cell Capacity Typical 2000 mah/0.2 CmA@20 Minimum 1900 mah/0.2 CmA@20
EECS 473 Advanced Embedded Systems. Lecture 10: Batteries and linear converters
EECS 473 Advanced Embedded Systems Lecture 10: Batteries and linear converters Order Stuffs Recall: Only can use petty cash for orders under $200. We can do reimbursements for amounts over $200. Slightly
Status & Future Perspectives of Li-Ion Batteries and PEM Fuel Cell Systems in the Automotive Industry
German-Japanese Energy Symposium 2011 Munich, 10 th February Dr.-Ing. Arnold Lamm, Senior Manager Daimler AG Group Research / 7th February 2011 Contents 1. Battery Requirements HEV/EV 2. Battery Development
CORDLESS TACKER MODEL NO: CCT48 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0414
CORDLESS TACKER MODEL NO: CCT48 PART NO: 6485070 OPERATION & MAINTENANCE INSTRUCTIONS LS0414 INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product, please read
AC/DC Compact Charger. for Digital Camera and Camcorder Batteries. Owner's Manual. Please read before using this equipment.
AC/DC Compact Charger for Digital Camera and Camcorder Batteries Owner's Manual Please read before using this equipment. Thank you for purchasing the Watson AC/DC Compact Charger. Browse through this
Discharge Capacity 1 (mah) Average Minimum Diameter Height
New Product H Type Nickel Metal Hydride Battery HHRAAAH, HHR1AH, HHR37AH, HHR5SCH, HHR3CH NiMH H Type Batteries September 4 Matsushita Battery Industrial Co., Ltd. Improved Characteristics at Higher s
Table of contents. Safety instructions...2. Diagram with e-bike specific components...3. Control panel...4
E-RIDE User s Guide Table of contents Safety instructions... Diagram with e-bike specific components...... Control panel... Important safety notes regarding battery charger...5 Charger function...6 Battery
ATD-5921 RECHARGEABLE 12 VOLT 18 AMP/HOUR JUMP START OWNERS MANUAL
ATD-5921 RECHARGEABLE 12 VOLT 18 AMP/HOUR JUMP START OWNERS MANUAL 900 PEAK AMPS/400 CRANKING AMPS OF STARTING POWER. STARTS CARS, TRUCKS, RV s AND BOATS WITHOUT THE NEED OF ANOTHER VEHICLE OR AC POWER
+91-8043048784 Accurate Ampere http://www.accurateampere.co.in/ We manufacture, wholesale, supply and distribute best quality Industrial Batteries and Chargers. Owing to their sturdy construction, compact