Self-Propelled Windrower

Transcription

1 Self-Propelled Windrower MacDon 9250/9350/9352/9352i/9352c Westward 9250/9350/9352/9352i/9352c Prairie Star 4940/4950/4952/4952i/4952c Premier 2940/2950/2952/2952i/2952c Harvest Pro 8140/8150/8152/8152i/8152c PARTS CATALOG Part #46583 $15

2

3 MacDon 9250, 9350, 9352, 9352i & 9352c / Westward 9250, 9350, 9352, 9352i & 9352c Prairie Star 4940, 4950, 4952, 4952i & 4952c / Premier 2940, 2950, 2952, 2952i & 2952c Harvest Pro 8140, 8150, 8152, 8152i & 8152c Self-Propelled Windrower Parts Catalog ALPHABETICAL INDEX... ii, iii CAB Cab Frame, Seals, Grommets & Mounts... 2,3 Cab Upholstery & Insulators... 4,5 Cab Door & Cab Right Side Panel... 6,7 Cab Roof (& Roof Electrical)... 8,9 Windows Footrest & Side Console Panel Steering Column... 12,13 Instrument Panel... 14,15 Side Console Reel & Conveyor Speed Control Ground Speed Lever... 18,19 Throttle Control Cummins Engine... 20,21 Throttle Control Isuzu Engine... 22,23 Cab Electrical & Wiper... 24,25 Seat... 26,27 Cab Air Conditioning & Blower Group... 28,29 Air Conditioning - Engine Group... 30,31 Heater Cummins Engine... 32,33 Heater Isuzu Engine... 34,35 TRACTOR Main Frame & Covers... 36,37 Lift Linkage... 38,39 Walking Beam & Pivot Rear Weight Package Tractor Electrical Engine Assembly Cummins Engine Engine Assembly Isuzu Engine Alternator Mounting Cummins Engine... 54, 55 Engine Superstructure... 56, 57 Fuel System... 58, 59 Engine Air Intake Cummins except XX52c... 60, 61 Engine Air Intake XX52i & XX52c... 62, 63 Engine Cooling... 64, 65 Air Intake Screen... 66, 67 Header Drive... 68, 69 Bevel Gearbox Driveline (Engine to Bevel Gearbox)... 74, 75 TABLE OF CONTENTS SERIAL BREAKS TRACTOR (continued) Header Drive Pulley Driveline: Tractor to Header, S.N Driveline: Tractor to Header, S.N Neutral Interlock & Pintle Arms Steering & Ground Speed... 80, 81 Hydraulics: Header Drive... 82, 83 Hydraulics: Cylinder Control Hydraulics: Header Lift Cylinder Seal Kits... 88, 89 Hydraulics: Traction Drive... 90, 91 Hydraulics: Triple Pump... 92, 93 Hydraulics: Double Gear Pump... 94, 95 Hydraulics: Two Speed Wheel Motor... 96, 97 Two-Speed Drive: Wheel Motor Ass y B Hydraulics: Single Speed Wheel Motor Single Speed Drive: Wheel Motor Ass y Power Wheel: Model , 103 Power Wheel: Model , 105 Power Wheel: Model 8B , 107 Power Hub: Model RR , 109 Auburn Replacement For RR Power Hub109A, 109B Drive Wheels & Tires , 111 Brake Assembly Cummins except XX52c , 113 Brake Assembly XX52i & XX52c , Forked Casters XX50/XX40 Tractors , Forked Casters XX50/XX40 Tractors , 119 Formed Casters XX50/XX40 Tractors , 121 Forked Casters XX52/XX52i/XX52c Tractors. 122, 123 Formed Casters XX52/XX52i/ XX52c Tractors124, 125 Safety Decals , 127 Information Decals, Reflectors & Paint , 129 Product Identification Decals , 131 Optional Hydraulics: Header Angle Kit , 133 Optional Hydraulics: Fore/Aft Kit , 135 Optional Hydraulics: Header Express Down Manifolds , 137 NUMERICAL LIST SUGGESTED STOCKING LIST , 149 The side of the serial number on which the dash (-) appears determines whether the part is used "up to" or "after" the serial number given. Example: Used on machines up to and including serial number Used on machines including and after serial number When ordering, be sure the complete and proper serial number is given. L/H - left hand R/H - right hand Left/Right Hand is determined from Operator's position, facing I.D. - inside diameter forward. O.D. - outside diameter A/R - as required (quantity varies) ABBREVIATIONS REF - reference, part number called up elsewhere in catalog NC - national coarse thread NF - national fine thread NA refers to the naturally aspirated tractor Turbo refers to the turbo diesel tractor HARDWARE Common hardware is not illustrated. Alphabetic references are used to designate position and description of these items. BOLDED PART S INDICATE RECENT CHANGES i

4 ii ALPHABETICAL INDEX A Air Cleaner & Pre-Cleaner - Cummins except XX52c Air Cleaner & Pre-Cleaner XX52i & XX52c Air Conditioning, Cab Air Conditioning, Engine Group Air Intake Screen Alternator B Belt, Fan/Alternator Cummins Engine Belt, Fan/Alternator Isuzu Engine Belt, Header Drive Blower, Cab Brake Assembly Cummins except XX52c 113 Brake Assembly XX53i, XX52c C Cab Seals, Grommets & Mounts... 3 Casters, Forked 9352 etc Casters, 16.5 Forked 9250/9350 etc Casters, 9.5 Forked 9250/9350 etc Casters, Formed 9250/9350 etc Casters, Formed 9352/9352i/9352c etc Center Link, Tractor to Header Compressor, A/C Condenser, A/C Control Knobs & Switches Conveyor Speed Control, Cab Cooler, Hydraulic Oil Cylinder, Header Clutch Cylinder, Header Lift Cylinder, Header Lift: Seal Kits... 88, 89 D Decals, Information Decals, Product Identification ,131 Decals, Safety Door, Cab... 7 Driveline: Engine to Bevel Gearbox Driveline: Tractor to Header, Prior to S.N Driveline: Tractor to Header, S.N and above 78 E Electrical, Cab Electrical, Ground Speed Lever Electrical, Roof... 9 Electrical, Tractor Engine Air Intake Cummins except XX52c. 61 Engine Air Intake XX52i & XX52c Engine Assembly Cummins Engine Engine Assembly Isuzu Engine Engine Cooling Engine Superstructure Evaporator, A/C F Fan, Engine Cummins Engine Fan, Engine Isuzu Engine Filter, Fuel Line Filter, Hydraulic Oil... 83, 84 Filters, Engine Oil & Fuel Cummins Engine Filters, Engine Oil & Fuel Isuzu Engine Footrest, Cab Frame, Cab... 3 Frame, Tractor Fuel System G Gauges Gearbox, Bevel Ground Speed Lever Ground Speed Linkage H Header Drive Header Drive Pulley Heater Cummins Engine Heater Isuzu Engine Hydraulics: Cylinder Control Hydraulics: Double Gear Pump Hydraulics: Header Drive Hydraulics: Optional Header Angle Kit Hydraulics: Optional Header Express Down Hydraulics: Optional Reel Fore-Aft Kit Hydraulics: Traction Drive Hydraulics: Triple Pump Hydraulics: Two Speed Wheel Motor Hydraulics: Single Speed Wheel Motor I Ignition Switch Instrument Panel L Ladder Lift Linkage M Manifolds, Supercharge Muffler Cummins Engine Muffler Isuzu Engine N Neutral Interlock Numerical List O Oil Pressure Switch Cummins Engine Oil Pressure Switch Isuzu Engine... 54

5 ALPHABETICAL INDEX iii P Paint Panel, Cab Right Side... 7 Panel, Cab Side Console Panels & Supports, Engine/Rad Pintle Arms, Traction Drive Power Wheel Auburn Gear Model Model Model 8B B Replacement for RR Hub B Power Hub - Model RR W Walking Beam & Pivot Weight Package, Rear Wheel Motor Ass'y: Single Speed Drive Wheel Motor Ass'y: Two Speed Drive Wheel Motor Components Wheels & Tires, Drive Windows Windshield Wiper R Radiator Radiator Supports Reel Speed Control, Cab Reflectors Roof, Cab (& Roof Electrical)... 9 S Seat Side Console, Cab Starter Cummins Engine Starter Isuzu Engine Steering Column Steering Linkage Stocking List, Suggested , 148 Switch, A/C Pressure Switch, Engine Oil & Temperature Cummins Engine 47 Switch, Engine Oil & Temperature Isuzu Engine Switch, Header and Reel Lift Switch, Header Drive Neutral Switch, Hydraulic Oil Pressure Switch, Neutral Switches, Side Console T Tank, Hydraulic Oil Temperature Sender & Switch Cummins Engine.. 51 Temperature Sender & Switch Isuzu Engine. 53 Throttle Control Cummins Engine Throttle Control Isuzu Engine Tires, Caster ,119,121,123,125 Tires, Drive Tool Box Two-Speed Drive: Wheel Motor Assembly U Upholstery... 5

6 2 CAB FRAME, SEALS, GROMMETS & MOUNTS

7 CAB FRAME, SEALS, GROMMETS & MOUNTS 3 REF PART DESCRIPTION QTY SERIAL CAB FRAME - with decals INSULATOR cab SEAL - foam, top front SEAL - foam, top side SEAL - foam, top rear SEAL - foam, window SEAL - foam SEAL - foam, blower ports SEAL - foam SEAL - moulded, window MOULDING - protective MOULDING - protective, right side CONDUIT - slit GROMMET INSULATOR - cab mount WASHER flat, 1/2 inch ID... 4 A BOLT - hex head, 1/2 NC x 3 inch (except front right) BOLT - hex head, 1/2 NC x 2-1/2 inch (front right only) B NUT - hex, 1/2 NC - double nutted (except front right) NUT - serrated flange, 1/2 NC - single nut (front right only) C WASHER - lock, 1/2 inch ID (except front right)

8 4 CAB UPHOLSTERY & INSULATORS

9 CAB UPHOLSTERY & INSULATORS 5 REF PART DESCRIPTION QTY SERIAL INSULATOR upper side, L/H & R/H, front INSULATOR - upper front, L/H & R/H INSULATOR - upper side, L/H & R/H, rear INSULATOR - upper left, rear INSULATOR - upper right, rear UPHOLSTERY - above front window UPHOLSTERY - above L/H side window UPHOLSTERY - above R/H side window UPHOLSTERY - above rear window UPHOLSTERY - left post UPHOLSTERY - right post UPHOLSTERY - below rear window UPHOLSTERY - door REF UPHOLSTERY - cab roof, see page FLOOR MAT... 1

10 6 CAB DOOR & CAB RIGHT SIDE PANEL

11 CAB DOOR & CAB RIGHT SIDE PANEL 7 REF PART DESCRIPTION QTY SERIAL DOOR with decals (does not include striping or model name/number decals) SEAL - door, moulded HANDLE - outer, with keys PANEL handle backup KEY - door LATCH - door ROD door opener STOP - door PANEL - right cab side ANGLE R/H panel mount WASHER steel/rubber 3/8 inch ID WASHER steel/rubber 1/4 inch ID SEAL R/H cab front PANEL front cab trim PANEL L/H cab trim SEAL L/H cab front HANDLE inside, door opening GRIP inside handle PIN - door latch PANEL door storage PANEL door storage back HANDLE inside, door closing INSULATOR door... 1 A BOLT - flange head, 3/8 NC x 1/2 B BOLT - hex head, 5/16 NC x 3/4 C SCREW self tapping D NUT - lock, smooth flange, 3/8 NC distorted thread E BOLT - hex head, 3/8 NC x 1-1/2 F NUT - lock, 1/2 NC distorted thread G WASHER flat, 13/32 I.D. H NUT - serrated flange, 3/8 NC J SCREW - self-drilling, self-tapping, #12 x 1 inch K NUT - hex, 5/16 NC L NUT - hex, 1/4-20 UNC M BOLT - hex head, 1/4 NC x 1/2 inch N BOLT - hex head, 1/4 NC x 1-1/4 P WASHER - lock, 1/4 inch ID Q NUT lock, 5/16 NC R BOLT - hex head, 1/4 NC x 1 inch S NUT lock, 1/4 NC T BOLT flange head, 3/8 NC x 3/4 U WASHER lock, M6 V BOLT hex head, M6 1.0 x 20 W WASHER flat, 1/4 inch ID X BOLT flng head, 3/8 NC x 1-1/4 Y NUT retaining, sm 3/8 NC Z SCREW 1/4 NC x 1 inch a BOLT rd hd, sq nk, 3/8 NC x 3/4 b NUT hex, 1/2 NC d WASHER flat, 9/32 inch ID ~ f REF Indicates where hardware passes through cab or door frame.

12 8 CAB ROOF

13 CAB ROOF 9 REF PART DESCRIPTION QTY SERIAL ROOF - cab, includes roof, headliner and items 2-6 inclusive INSULATOR - roof NUT - tee, #10 NC (for wiper motor and amber light mounting) NUT - spring, #6 NC (for field & head lamps) SPACER - roof/headliner, front SPACER roof/headliner, rear WASHER - flat PAD REF GROMMET - See Cab Frame LIGHT - amber, replacement bulb # OPTICAL UNIT 3 x 5 inch BULB 12V, 55W LIGHT headlight SOCKET light bulb, for headlight BULB lamp, (SP 11), for headlight LIGHT headlight BULB lamp, designation: 9005, for headlight GASKET headlight, for item SUPPORT headlight SPRING compression, headlight GASKET lamp, for item BEZEL - lamp LIGHT - interior LIGHT pedestal work OPTICAL UNIT for item BULB 12V, 55W, for item BEZEL for item LIGHT - turn indicator NUT - spring MIRROR MOUNT mirror CONDUIT - slit hose HARNESS - electrical, roof (was 45828), incl plus (2) HARNESS electrical, roof HARNESS headlight adapter, Packard to female blade SUPPORT - rear, radio SPEAKER - radio GRILLE - speaker ANTENNA radio, includes cable BAR antenna backing GRIP cover, antenna DECAL - covering, radio cut-out SEAL - foam GROMMET harness PANEL radio support... 1 A BOLT - hex head, 1/2 NC x 7-1/2 B NUT - lock, 1/2 NC distorted thread C BOLT - hex head, 1/2 NC x 9 inch D BOLT - hex head, M x 50 E NUT lock, #10 32 NC F SCREW - self tap, #8 x 3/4 inch G SCREW - machine, #6 NC x 1 inch H NUT lock, smooth flange, 3/8 NC d.t. J WASHER flat, 13/32 ID K SCREW machine, #10 x 1/2 inch L NUT #10 NC M BOLT flange, lock N NUT flange, lock, M10 x 1.5 P WASHER flat, M10

14 10 WINDOWS REF PART DESCRIPTION QTY SERIAL SEAL - top, front windows SEAL - bottom, front windows WINDOW - front WINDOW - side REF SEALANT - black, use neutral cure silicone (Silicone II or Silglaze)... AR WINDOW - rear SEAL - rear window WINDOW - right, assembly (includes item 9) SUPPORT - window LATCH - rear LATCH - front FASTENER GROUP - latch (includes screw, bushing and nut) SEAL - door window WINDOW - door RIVET - latch RETAINER window retaining, lower INSULATOR window, lower front ANGLE window, upper HANDLE wiper... 1 A BOLT - flange head, 1/4 NC x 1/2 inch B SCREW - self drilling, self tapping, #12 x 1 inch C NUT jam, 1/2 NC

15 FOOTREST & SIDE CONSOLE PANEL 11 REF PART DESCRIPTION QTY SERIAL ROD - footrest PANEL - side console, includes items 3, 4, 5 and SEAL - top SEAL - vertical SEAL - front vertical SEAL - A/C compartment... 1 A NUT - serrated flange, 3/8 NC B NUT - lock, smooth flange, 3/8 NC distorted thread R REF Hardware passes through seat support panel.

16 12 STEERING COLUMN

17 STEERING COLUMN 13 REF PART DESCRIPTION QTY SERIAL SHAFT - steering, with sprocket BUSHING - shaft WASHER - flat, 13/16 inch I.D U-JOINT SHAFT - steering, upper PIN - spring, 1/4 x 1 inch TUBE - steering SPRING gas, adjuster YOKE for item BUSHING - lower BUSHING - upper PIN - spring, 1/4 x 1-1/4 inch SPACER - column KNOB GUIDE - rubber INSULATOR - steering post, foam PIN spring, 3/8 x 2 inch (was 21095) WHEEL - steering, with cap (item 19) CAP - steering wheel INSTALLATION KIT - includes hub, snap plate & bolts COVER upper steering column GASKET SPEEDOMETER SPEEDOMETER COVER lower steering column PIN spring, 3/8 x 1 inch... 1 NOTE: For Related Parts, see "Steering & Ground Speed", page 81. A NUT hex, 3/8 NC B BOLT hex head, 3/8 NC x 2-1/2 inch C BOLT round head, 3/8 NC x 1-1/4 inch D NUT hex head, jam nut, M10 1 E SCREW Phillips pan head, #6 x 1/2 inch

18 14 INSTRUMENT PANEL

19 INSTRUMENT PANEL 15 REF PART DESCRIPTION QTY SERIAL PANEL - instrument, with decal (was ) GAUGE - fuel GAUGE - voltmeter GAUGE - temperature, engine coolant, all except XX52i tractors GAUGE - temperature, engine coolant, XX52i tractors only SWITCH - ignition KEY - ignition, for switch KEY spare for switch VENTILATOR LIGHTER - cigarette MONITOR MONITOR, all except XX52i & XX52c tractors MONITOR, XX52i tractors only MONITOR, XX52c tractor only HOLDER cup SWITCH push button, cold start, XX52i & XX52c tractors only A SCREW hex washer head, #10 x 1/2 inch self tapping B WASHER flat, 7/8 inch ID C SCREW hex washer head, #10 x 5/8 inch self tapping

20 16 SIDE CONSOLE REF PART DESCRIPTION QTY SERIAL PANEL - console, with decal - includes items 2 & 15 and hardware SEAL - right post FLASHER CONTROL - with knob SWITCH - light, with knob SWITCH - wiper KNOB - control SWITCH - blower THERMOSTAT ASSEMBLY ASHTRAY SWITCH - toggle, header drive GUARD - for toggle switch REF SWITCH reel & conveyor speed control, see page SWITCH - deck shift, 960 & 972 Hydraulic Deck Shift Headers PANEL - access TERMINAL power outlet, 12 volt CAP power outlet ARMREST SUPPORT armrest BAR with weld nuts, for item KNOB armrest support SWITCH 2 speed, c/w decal (turbo only) SWITCH header express down, see page OPT KNOB access panel HOLDER cup A SCREW - button head, rib neck #12 NC x 5/8 inch B NUT - lock, #12 NC distorted thread C BOLT hex head, 1/4 NC x 5/8 inch D SCREW M6 x 15 mm E SCREW hex washer head, #10 x 5/8 inch, self tapping

21 REEL & CONVEYOR SPEED CONTROL 17 REF PART DESCRIPTION QTY SERIAL KNOB - control WASHER - non metal PIN - roll, 1/4 x 1-3/4 inch SPACER HOSE REF CONTROL BLOCK - header drive, see "Header Drive Hydraulics"... 1 B BOLT-hex head, 1/4 NC x 5/8 inch

22 18 GROUND SPEED LEVER

23 GROUND SPEED LEVER 19 REF PART DESCRIPTION QTY SERIAL LEVER - ground speed BUSHING - plastic (part consists of two halves) FLANGE - bushing mounting HANDLE - ground speed HARNESS - ground speed lever, includes items 6 (qty.2), 7, 18 & decals SWITCH rocker, reel lift, and header lift PLATE face, handle BOLT - hook REF CABLE - neutral interlock, see "Neutral Interlock & Pintle Arms" REF ROD - steering, see "Steering & Ground Speed" INSULATOR - rubber WASHER - flat PAD - friction BUSHING - plastic SPRING - compression WASHER - flat PLUG nylon, diameter hole SWITCH 4 way, header angle/fore aft, see page 133 & OPT A NUT - lock, smooth flange, 5/16 NC distorted thread B WASHER flat, 11/32 inch ID C SCREW set, 5/16 NC x 1/4 inch D NUT - hex, 3/8 NC E BOLT - round head, square neck, 1/2 NC x 5 inch F NUT - lock, 1/2 NC distorted thread G NUT - hex, 1/2 NC H SCREW self tapping, #8 NC x 1-1/2 inch ~ f REF Indicates where hardware passes through frame member.

24 20 THROTTLE CONTROL CUMMINS ENGINE TRACTORS Models XX52c have cab end throttle components only. Engine end is electronic, with harness.

25 THROTTLE CONTROL CUMMINS ENGINE TRACTORS 21 REF PART DESCRIPTION QTY SERIAL SUPPORT - throttle, in-cab LEVER - throttle PAD - friction SPRING - compression PLATE throttle arm KNOB - orange CABLE - throttle PIVOT - cable HOLDER - cable BAR - spacer SPRING - extension, to fuel pump lever (N.A. engine) SUPPORT - cable to spring (N.A. engine) SUPPORT cable to spring (N.A engine) SUPPORT - throttle cable, engine end (N.A. Engine) INSULATOR - rubber, throttle cable SPRING extension CLEVIS - throttle cable LEVER - throttle GROMMET - rubber CLIP cable holder LEVER - throttle SENSOR - rotary SUPPORT - throttle SPRING - compression BRACKET - throttle spring... 1 A BOLT - hex head, 3/8 NC x 1-1/4 inch B BOLT - round head, square neck, 3/8 NC x 1 inch C SCREW - machine, #10 NC x 1/2 inch D NUT - hex, #10 NC E NUT - lock, smooth flange, 3/8 NC distorted thread F BOLT round head, square neck, 3/8 NC x 1-1/4 inch G PIN - cotter, 3/32 x 3/4 inch H NUT - hex, #10 NF J SCREW - machine, #10 NC x 3/4 inch K BOLT - flange head, 3/8 NC x 3/4 inch L BOLT - hex head, M6 x 15 mm M WASHER - lock, M6 N BOLT - hex head, 3/8 NC x 1-1/2 inch P NUT - hex, 3/8 NC Q WASHER flat, 13/32 inch ID R BOLT - round head, square neck, 5/16 NC x 1-1/2 inch S NUT - lock, smooth flange, 5/16 NC distorted thread V NUT hex, 1/4 NC W BOLT 1/4 NC x 1 inch X NUT flange, # in, zn pl, gr 5, serrated face Y BOLT round head, square neck, #10-24 nc x1.5" long ~ f REF Indicates where hardware passes through frame member.

26 22 THROTTLE CONTROL ISUZU ENGINE TRACTORS

27 THROTTLE CONTROL ISUZU ENGINE TRACTORS 23 REF PART DESCRIPTION QTY SERIAL SUPPORT - throttle, in-cab LEVER - throttle PAD - friction SPRING - compression PLATE throttle arm KNOB - orange CABLE - throttle PIVOT - cable HOLDER - cable BAR - spacer INSULATOR - rubber, throttle cable CLIP cable holder INSULATOR throttle REF LEVER fuel pump REF SUPPORT throttle, see Fuel System YOKE throttle... 1 A BOLT - hex head, 3/8 NC x 1-1/4 inch C SCREW - machine, #10 NC x 1/2 inch D NUT - hex, #10 NC E NUT - lock, smooth flange, 3/8 NC distorted thread F BOLT round head, square neck, 3/8 NC x 1-1/4 inch G PIN - cotter, 3/32 x 3/4 inch H NUT - hex, #10 NF J SCREW - machine, #10 NC x 3/4 inch K BOLT - flange head, 3/8 NC x 3/4 inch Q WASHER flat, 13/32 inch ID W BOLT 1/4 NC x 1 inch X BOLT flange head, 3/8 NC x 3/4 inch Y WASHER flat, 9/32 inch ID Z NUT lock, 1/2 NC, distorted thread ~ f REF Indicates where hardware passes through frame member.

28 24 CAB ELECTRICAL & WIPER

29 25 CAB ELECTRICAL & WIPER REF PART DESCRIPTION QTY SERIAL HARNESS - cab wiring, with plug and boot (item 25) HARNESS - cab wiring, with plug and boot (item 25) (was 45969/111449/112965) SUPPORT - circuit breakers BREAKER - 6 amp, head lights and work lights BREAKER 10 amp, header functions BREAKER 12 amp, header functions, XX52i/XX52c brake and header functions BREAKER - 25 amp, air conditioning MOTOR wiper (was ) ARM - wiper BLADE - wiper PLATE - wiper RELAY - electrical FASTENER - plastic tie, push mount FASTENER - plastic tie CABLE - ground SWITCH - park brake SUPPORT wiper REF HANDLE wiper, see Windows HARNESS speedometer CLIP for harness, item BOOT rubber... 1 A WASHER - lock, #10 B NUT - hex, #10-24 NC C NUT - serrated flange, 1/4 NC D WASHER - flat, 13/32 inch ID E SCREW hex head, 1/4-28 UNF x 3/4 inch F WASHER lock, 1/4 inch ID G NUT 5/16 NC H SCREW - hex head, #12 NC x 1-1/2 inch J BOLT - flange head, 3/8 NC x 3/4 inch K NUT - lock, smooth flange, 3/8 NC distorted thread L BOLT round head, square neck, 1/4 NC x 1-3/4 inch M SCREW hex head, 1/4 NC x 1 inch N NUT 1/4 NC P NUT jam, 1/2 NC Q SCREW hex head, #10 NC x 3/8 inch R NUT hex, #10-32 NF S SCREW self tapping, #10 x 1/2 inch T NUT serrated flange, 3/8 NC

30 26 CAB SEATS

31 SEAT 27 REF PART DESCRIPTION QTY SERIAL SEAT - air suspension, complete (was ) SEAT CUSHION drivers seat SEAT CUSHION drivers seat BACKREST CUSHION drivers seat BACKREST CUSHION drivers seat ARMREST left, drivers seat (for R/H armrest, see Side Console, p. 16) ARMREST left, drivers seat (for R/H armrest, see Side Console, p. 16) PAD L/H armrest SLIDE SERVICE KIT - includes both sides & latch wire AIR CONTROL VALVE SERVICE KIT - includes valve, knob & hardware KNOB air valve with set screw COMPRESSOR / WIRE HARNESS SERVICE KIT includes:... 1 compressor, harness & hardware (was 42934) KNOB SERVICE KIT includes: back tilt knob (item 26) and recliner handle assembly lumbar support knob fore-aft knob KNOB fore-aft isolator SEAT BELT drivers seat SWITCH seat SWITCH seat HARNESS seat switch HARNESS seat switch VERTICAL SUSPENSION SHOCK SERVICE KIT FORE-AFT ISOLATOR SHOCK SERVICE KIT BEARING SERVICE KIT - includes all bearings AIR LINE & FITTING SERVICE KIT AIR LINE & FITTING SERVICE KIT AIR SPRING (air bag) PANEL - seat, with seals SEAL - foam CUSHION trainers seat ANGLE trainers seat mount ROD trainer seat SUPPORT trainers seat SEAT BELT trainers seat CLIP for cab harness KNOB seat back tilt RECLINER KIT knob, brackets, springs & hardware RECLINER KNOB KNOB lumbar with roll pin SEAT TOP assembly SEAT ADAPTER PLATE A NUT - lock, smooth flange, 3/8 NC distorted thread B BOLT flange, 3/8 NC x 5/8 inch C BOLT socket, button head, 3/8 NC x ½ inch D BOLT - hex head, M8 x 20 mm E WASHER - lock, M8

32 28 CAB AIR CONDITIONING & BLOWER GROUP

33 CAB AIR CONDITIONING & BLOWER GROUP 29 REF PART DESCRIPTION QTY SERIAL VALVE - expansion O-RING - evaporator to expansion valve HOSE - air conditioning, liquid HOSE - air conditioning, suction INSULATOR - foam RETAINER - evaporator EVAPORATOR / HEATER CORE BAFFLE - foam PAN - condensate, (includes foam pad bonded to underside of pan) HOSE - drain CLIP - drain hose PAD - rubber BLOWER - complete VENTILATOR - circular VENTILATOR - rectangular FILTER - return air, (located on cab rear wall) GRILL - return air filter KNOB - plastic CLEANER - air intake, (located under rear overhang of cab roof) RETAINER - cleaner KNOB - plastic THERMOSTAT - with capillary tube & conduit SWITCH - blower control KNOB - control SWITCH - low pressure O-RING - for hose O-RING - for hose HOLDER blower RESISTOR blower... 1 A NUT - lock, smooth flange, 3/8 NC distorted thread B BOLT - flange head, 3/8 NC x 3/4 inch C BOLT - round head, square neck, 3/8 NC x 3/4 inch F SCREW self tapping ~ f REF Indicates where hardware passes through frame member. NOTE: For related parts, see "Air Conditioning - Engine Group", page 31.

34 30 AIR CONDITIONING - ENGINE GROUP

35 AIR CONDITIONING - ENGINE GROUP 31 REF PART DESCRIPTION QTY SERIAL CONDENSER (includes item 20) O-RING - condenser to drier (2) & switch to drier DRIER/RECEIVER SWITCH - high pressure - with O-ring BAND - drier mount SUPPORT - drier HOSE - air conditioning, liquid HOSE - air conditioning, discharge GROMMET - hose protector COMPRESSOR - see Note BELT - compressor drive BAR - belt tightener, all except XX52i tractors MOUNT engine, with alternator belt tightener, XX52i tractors only HOSE - air conditioning, suction STRIP - hose protector HOLDER - hose O-RING - for hose O-RING - for hose O-RING - for hose HOSE - air conditioning, liquid FITTING - adapter (brazed on to condenser) GUARD coolers... 1 A NUT - lock, smooth flange, 3/8 NC distorted thread B BOLT round head, square neck, 3/8 NC x 3/4 inch C BOLT round head, square neck, 1/4 NC X 3/4 inch D NUT - hex, 3/8 NC E BOLT - hex head, 1/2 NC x 1-1/2 inch F BOLT round head, square neck, 3/8 NC x 1-1/4 inch G BOLT round head, square neck, 3/8 NC x 1 inch H BOLT - hex head, 3/8 NC x 1-1/4 inch L NUT lock, 1/4 NC distorted thread ~ f REF Indicates where hardware passes through frame or support member. NOTES: 1. For related parts, see "Cab Air Conditioning & Blower Group", page Compressor includes total system requirement of refrigerant oil: 240 cc (8.1 US fl.oz.) SP-16 PAG.

36 32 HEATER CUMMINS ENGINE TRACTOR

37 HEATER CUMMINS ENGINE TRACTOR 33 REF PART DESCRIPTION QTY SERIAL VALVE - heater SUPPORT - heater valve TUBE - heater control WASHER flat, sae 9/32 inch ID KNOB - control CLAMP hose, gear type HOSE - heater, valve to bottom of heater core HEATER CORE / EVAPORATOR HOSE - heater, engine water pump housing to top of heater core HOSE heater, engine shut-off valve to top of heater core HOSE - heater, valve to top of engine block (fan end) FITTING - heater, 1/2 NPT x 5/8 inch ID hose (was 6137), (qty = 1 up to SN ) CLIP - insulated VALVE - shut off CLAMP hose, constant tension type, (qty = 2 up to SN ) VALVE shut off HOSE heater, shut-off valve to engine water pump housing A SCREW - self tapping, #10 x 3/8 inch B NUT - serrated flange, #10 NC C SCREW - machine, #10 NC x 1/2 inch D BOLT - round head, square neck, 3/8 NC x 3/4 inch E NUT - lock, smooth flange, 3/8 NC distorted thread F BOLT hex head, 3/8 NC x 3/4 inch ~ f REF Indicates where hardware passes through frame or support member.

38 34 HEATER ISUZU ENGINE TRACTOR

39 35 HEATER ISUZU ENGINE TRACTOR REF PART DESCRIPTION QTY SERIAL VALVE - heater SUPPORT - heater valve TUBE - heater control WASHER flat, sae 9/32 inch ID KNOB - control CLAMP hose, gear type HOSE - heater, valve to bottom of heater core HEATER CORE / EVAPORATOR HOSE - heater, engine water pump housing to shut off valve HOSE - heater, valve to top of engine block (fan end) FITTING elbow, 1/2 NPT x 5/8 inch ID hose CLIP - insulated VALVE - shut off CLAMP hose, constant tension type HOSE heater, shut off valve to engine water pump housing ELBOW heater supply (Isuzu # )... 1 A SCREW - self tapping, #10 x 3/8 inch B NUT - serrated flange, #10 NC C SCREW - machine, #10 NC x 1/2 inch D BOLT - round head, square neck, 3/8 NC x 3/4 inch E NUT - lock, smooth flange, 3/8 NC distorted thread F BOLT hex head, 3/8 NC x 3/4 inch ~ f REF Indicates where hardware passes through frame or support member.

40 36 MAIN FRAME & COVERS REPLACEMENT TOOLBOX

41 MAIN FRAME & COVERS 37 REF PART DESCRIPTION QTY SERIAL 1 REF FRAME - main, not serviced COVER - left inner leg COVER - right inner leg LADDER step, left side (was 45860) REF COVER - engine, see "Engine Superstructure" TOOL BOX (see note 1) BRACKET toolbox mounting HOLDER grease gun BRACKET right ladder LADDER step, right side ARM right ladder KNOB toolbox bracket PLATE mount BRACKET toolbox holder BRACKET toolbox TOOLBOX A BOLT - hex head, 3/8 NC x 1 inch B NUT - lock, smooth flange, 3/8 NC distorted thread C BOLT - flange head, 1/2 NC x 1 inch D WASHER flat, 1/2 inch ID E NUT flange, 1/2 NC F WASHER flat G BOLT round head, square neck, 3/8 NC x 3/4 inch H BOLT hex head, 3/8 NC x 1-1/2 inch J NUT hex, 3/8 NC K WASHER flat, 13/32 inch ID L SCREW hew wash hd thd rolling 3/8 NC X 1.0 ~ f REF Indicates where hardware passes through frame member. NOTE: If prior production toolbox (item ) is not available, kit will be substituted. This Kit includes items and applicable hardware.

42 38 LIFT LINKAGE

43 LIFT LINKAGE REF PART DESCRIPTION QTY SERIAL SPRING - extension INSERT - spring SUPPORT - front spring mount BAR - front mount TUBE front mount CLEVIS - rear mount PIN - straight, rear spring DRAW BOLT - spring, hex head WASHER - flat, hardened PIN - "L" PIN - hair SUPPORT - linkage, with decals SUPPORT linkage, with decals BLOCK - wear (shown positioned for 920, 930 or 940 series headers) BAR - wear block PAD - rubber, lower leg PLATE - pad cover WASHER - flat ARM - top link, with lube fitting (item 19) FITTING - lube PIN - top link (rear) PIN - cylinder (rear) and top link (front) PLATE - header levelling PAD - rubber, top link REF CYLINDER - header lift, see "Hydraulics: Cylinder Control, page PIN - cylinder (front) BAR - cylinder mount STOP - cylinder HOOK - cylinder stop PIN - clevis, center link JOINT ASSEMBLY - center link, includes items 31 to JOINT - ball, R/H thread (header end) COLLAR - locking PIN - roll TUBE - center link JOINT - ball, L/H thread (tractor end) BAR - header height gauge, with indicator decal PLATE left, center link extension PLATE right, center link extension EXTENSION wear block, header only PLATE L/H, shallow angle kit PLATE R/H, shallow angle kit SPACER lower leg, shallow angle kit CHANNEL retainer, shallow angle kit TUBE spacer, shallow angle kit SUPPORT shallow angle kit B4482 KIT shallow angle, consists of items OPT (Kit available through WholeGoods only) WASHER flat, cropped B2773 KIT auxiliary float spring kit (includes one each of items 49 52)... OPT SPRING auxiliary spring... A/R INSERT auxiliary float spring... A/R INSERT auxiliary float spring... A/R INSERT auxiliary float spring... A/R A NUT - hex, 5/8 NC B BOLT - hex head, 3/8 NC x 1-1/2 inch C BOLT - hex head, 3/8 NC x 2 inch D NUT - lock, smooth flange, 3/8 NC dist. thd. E WASHER - flat, 13/32 inch ID F BOLT rnd hd, sq nk, 1/2 NC x 1 inch G BOLT - hex head, 3/8 NC x 3/4 inch H NUT - lock, 1/2 NC nylon insert J BOLT - round head, sq nk, 1/2 NC x 3 inch K NUT lock, 3/4 NC L BOLT - rnd hd, sq nk, 3/8 NC x 3/4 inch M BOLT - rnd hd, sq nk, 3/8 NC x 1-1/4 inch N WASHER - lock, 3/8 inch ID P NUT - hex, 3/8 NC Q BOLT hex head, 3/4 NC x 6-1/2 inch R BOLT - hex head, 1/2 NC x 1-1/2 inch S NUT lock, 1/2 NC distorted thread T BOLT - hh, 1/2 NC x 3-1/4, Multi-Crop Headers T BOLT hh, 1/2 NC x 5 inch: Draper Headers U NUT - lock, 3/8 NC distorted thread V BOLT - round head, sq nk, 3/8 NC x 1 inch W BOLT hex head, 3/4 NC x 1-1/2 inch X WASHER - flat, 13/16 inch ID Z BOLT hex head, 1/2 NC x 1 inch a NUT side lock, 3/4 NC dist. thd. b NUT lock, smth flg, 1/2 NC d BOLT rnd hd, sq nk, 1/2 NC x 3-1/2 inch e BOLT hex head, 1/2 NC x 1-3/4 inch g WASHER flat h BOLT hex head, 1/2 NC x 2-1/4 inch ~ f REF Indicates hardware passes thru frame... - MacDon 9250/9350, Westward 9250/9350, Prairie Star 4940/4950, Premier 2940/2950, Harvest Pro 8140/ MD 9352/9352i/9352c, WP 9352/9352i/9352c, PS 4952/4952i/4952c, PR 2952/2952i/2952c, HP8152/8152i/8152c 39

44 40 WALKING BEAM & PIVOT REF PART DESCRIPTION QTY SERIAL BEAM - walking, with bushings, lube fitting & decals (not as illustrated) BEAM - walking, with bushings, lube fitting & decals (was ) BUSHING steel...(see note 1) FITTING - lube PIVOT - walking beam SIGN SMV, reflector KIT REWORK, caster pivot, incl. 2 of items 7, 8 & 9 + instructions DISC walking beam BUSHING channel weldment FITTING lube, 1/4 NF A BOLT - hex head, 3/4 NC x 2-1/2 inch C WASHER - lock, 3/4 inch ID D NUT - hex, 3/4 NC E WASHER - flat, 13/16 inch ID F SCREW self tapping, 1/4 NC x 1/2 inch NOTES: 1.) For all tractors and tractors serial # & below qty = 2, For tractors serial # & above qty = 6. - MacDon 9250/9350, Westward 9250/9350, Prairie Star 4940/4950, Premier 2940/2950, Harvest Pro 8140/ MD 9352/9352i/9352c, WP 9352/9352i/9352c, PS 4952/4952i/4952c, PR 2952/2952i/2952c, HP8152/8152i/8152c

45 REAR WEIGHT PACKAGE 41 REF PART DESCRIPTION QTY SERIAL 1 B2266 KIT rear weight (in frame pkg), includes 187 lbs (85KG) weight pack & hardware * 2 B2980 KIT standard (behind frame pkg), includes 400 lbs (181KG) weight pack & hardware 3 B2981 KIT Additional six plates = 300 lbs (136KG), requires item 2 for installation SUPPORT weight box (was ) CAP weight box, 4-bolt design (not shown) CAP weight box PLATE weight (qty. 12 with B2980 & B2981)... 6 * 1 or 2 kits B2266 may be installed, as required. Two of B2266 are factory installed for 9352/4952/2952/8152 Tractors Serial No and up. (Kits are available through Wholegoods only). A BOLT - hex head, 3/4 NC x 3 inch B NUT - hex jam, 3/4 C SCREW self tapping, 3/8 x 5/8 inch F BOLT hex head, 3/4 NF x 2-3/4 inch G NUT lock, 3/4 NF H WASHER flat, 3/4 inch ID I BOLT hex head, 5/8 NC x 6-1/2 inch J BOLT hex head, 5/8 NC x 2-1/2 K NUT hex head, 5/8 NC

46 42 TRACTOR ELECTRICAL

47 TRACTOR ELECTRICAL 43 REF PART DESCRIPTION QTY SERIAL HARNESS - wiring, tractor section, includes item 22 (was 45830) HARNESS - wiring, tractor section, includes item HARNESS - wiring, tractor section, includes item HARNESS - wiring, tractor section, includes item FUSE automatic ATO type, 7.5 amp, component of harness CAP fuse holder, component of harness HARNESS - wiring, tractor section, includes item HARNESS - wiring, engine control, Cummins tier 2 turbo CONNECTOR KIT 3 way (includes male and female plugs) CONNECTOR KIT 2 way (includes male and female plugs) FASTENER - cable tie 7 ½ inch... see note FASTENER - cable tie, push mount GROMMET GROMMET (was 42415) CLIP harness, 3/8 inch ID... see note HOLDER - battery CABLE - starter to battery CABLE starter to battery CABLE starter to battery, includes cap nut INSULATOR - starter COVER - battery cable CABLE - ground, battery and engine mount to frame (was 5903 & 24289) FASTENER - cable tie 14 inch LIGHT - red, replacement bulb # LIGHT pedestal work OPTICAL UNIT for item BULB for item BEZEL for item BREAKER - circuit, 50 amp SUPPORT relay/breaker SUPPORT relay/breaker SUPPORT relay/breaker RELAY - electrical HARNESS wiring, adapter (N.A. only) SUPPORT R/H tail light SUPPORT L/H tail light TERMINAL diode, compressor circuit RELAY electrical, (qty. = 3 for XX52i and XX52c) MOULDING edge HOSE slit, fuel line protector (50mm long) HOSE slit, hydraulic line protector (200mm long) CLIP wiring, 15/16 inch ID RESISTOR control CLIP harness CLIP harness, 5/8 inch ID COVER fuse block, with foam & decal FOAM 435 x 15 x 3 mm FOAM 78 x 19 x 19 mm CABLE ground, starter to alternator CABLE ground, starter to block MacDon 9250/9350/9352, Westward 9250/9350/9352, Prairie Star 4940/4950/4952, Premier 2940/2950/2952, Harvest Pro 8140/8150/ MacDon 9352i, Westward 9352i, Prairie Star 4952i, Premier 2952i, Harvest Pro 8152i - MacDon 9352c, Westward 9352c, Prairie Star 4952c, Premier 2952c, Harvest Pro 8152c NOTES: 1.) Item 3, for XX40/XX50 Tier 1 tractors qty. = 14, Tier 2 = 16, XX52 tractors qty. = 12, XX52i tractors qty. = 11, XX52c tractors qty = 16 2.) Item 7, for XX40/XX50 tractors up to SN qty. = 10, SN & up = 8, XX52 tractors qty. = 11, XX52i tractors qty. = 12, XX52c tractors qty = 8

48 44 TRACTOR ELECTRICAL (Continued)

49 TRACTOR ELECTRICAL (Continued) 45 REF PART DESCRIPTION QTY SERIAL A BOLT - rd hd, sq nk, 3/8 NC x 3/4 B NUT - lock, smth flg, 3/8 NC dist thd C BOLT - hex head, M8 x 16 mm D BOLT rd hd, sq nk, 3/8 NC x 1 E WASHER flat, 13/32 inch ID F BOLT - flg hd, 3/8 NC x 3/4 inch G BOLT - hex head, M10 x 25 mm H NUT - hex, M6 J WASHER - lock, M6 K BOLT - rnd hd, sq nk, 3/8 NC x 2 L BOLT - hex head, 3/8 NC x 1 inch M WASHER - lock, #10 N Bolt hex head, M12 x 25mm lg P NUT lock, flng, M10 x 1-1/2 inch Q BOLT rd hd, sq nk, 1/4 NC x 1/2 R NUT jam, 3/8 NC S SCREW self tapping, 5/16 x ½ T SCREW - machine, #10 NC x 1/2 U NUT - serrated flange, #10 NC V NUT - hex, #10 NF W WASHER - lock, 1/4 inch ID X WASHER flat, #10 ID Y NUT - serrated flange, 1/4 NC Z NUT - hex, 1/4 NC a BOLT hex head, 1/4 NC x 5/8 d BOLT hex hd, M10 x 16 mm e SCREW self tap, 1/4 NC x 1/2 inch f SCREW self tapping, #10 x 5/8 - MacDon 9250/9350/9352, Westward 9250/9350/9352, Prairie Star 4940/4950/4952, Premier 2940/2950/2952, Harvest Pro 8140/8150/ MacDon 9352i, Westward 9352i, Prairie Star 4952i, Premier 2952i, Harvest Pro 8152i - MacDon 9352c, Westward 9352c, Prairie Star 4952c, Premier 2952c, Harvest Pro 8152c NOTES: 1.) Item 3, for XX40/XX50 Tier 1 tractors qty. = 14, Tier 2 = 16, XX52 tractors qty. = 12, XX52i tractors qty. = 11, XX52c tractors qty = 16 2.) Item 7, for XX40/XX50 tractors up to SN qty. = 10, SN & up = 8, XX52 tractors qty. = 11, XX52i tractors qty. = 12, XX52c tractors qty = 8

50 46 ENGINE ASSEMBLY CUMMINS ENGINE TRACTOR UNITS

51 ENGINE ASSEMBLY CUMMINS ENGINE TRACTOR UNITS 47 REF PART DESCRIPTION QTY SERIAL 1 REF ENGINE Cummins diesel, 80 hp N.A (not serviced)... 1 REF ENGINE Cummins diesel, 108 hp Turbo (not serviced)... 1 REF ENGINE Cummins diesel, 110 hp Tier II Turbo (not serviced) SUPPORT - front right SUPPORT - front left, with decal MOUNT - support INSULATOR - front engine mounts SUPPORT - rear INSULATOR - rear engine mounts WASHER - flat, 17/32 ID x 1-3/8 OD x 3/16 inch thick (was 25900) WASHER - flat, 17/32 ID x 2-1/2 OD x 3/16 inch thick SENDER - temperature SWITCH - temperature FITTING - reducer bushing, 3/8 NPT x 1/2 NPT SWITCH - oil pressure FITTING - heater, 1/2 NPT x 5/8 hose (was 6137) VALVE FITTING heater, 1/2 NPT x 5/8 hose MUFFLER (N.A only) CLAMP - muffler TUBE - exhaust MUFFLER (Turbo only) CLAMP - muffler FAN - engine cooling (N.A only) FAN engine cooling (Turbo only) SPACER - fan WASHER - hardened BOLT - hex head, M10 x 90 mm BELT - fan / alternator BELT - fan / alternator FITTING - barbed, 1/4 NPT x 5/16 hose, fuel line (N.A only) FITTING barbed elbow, 1/4 NPT x 5/16 hose, fuel line (Turbo only) FITTING barbed elbow, both NA & turbo STARTER - with decal, (Cummins # NW plus MacDon decal 42130) FILTER ELEMENT - oil (Cummins # ) FILTER ELEMENT - oil (Cummins # ) FILTER ELEMENT - fuel, primary, with water trap (Cummins # ) FILTER ELEMENT - fuel, primary, with water trap (Cummins # ) FILTER ELEMENT - fuel, primary, with water trap (Cummins # ) turbo only FILTER ELEMENT - fuel, secondary (Cummins # ) REF ALTERNATOR - see "Alternator Mounting" SHIELD starter MOULDING edge SUPPORT harness, turbo

52 48 ENGINE ASSEMBLY CUMMINS ENGINE TRACTOR UNITS

53 ENGINE ASSEMBLY CUMMINS ENGINE TRACTOR UNITS 49 REF PART DESCRIPTION QTY SERIAL A BOLT - hex head, M12 x 30 mm B WASHER - lock, M12 C WASHER - flat, M12 D WASHER - lock, 1/2 inch ID E NUT - hex, 1/2 NC F BOLT - hex head, 1/2 NC x 1-1/2 inch G BOLT - hex head, 1/2 NC x 1-3/4 inch H WASHER - flat, 17/32 inch ID I BOLT round head, square neck, 3/8 NC x 3/4 inch J BOLT - hex head, 1/2 NC x 3 inch K BOLT - hex head, M10 x 35 mm L WASHER - lock, M10 M NUT - hex, M10 N BOLT hex head, M12 x 25 mm P NUT flange, 3/8 NC

54 50 ENGINE ASSEMBLY ISUZU ENGINE TRACTOR UNITS

55 ENGINE ASSEMBLY ISUZU ENGINE TRACTOR UNITS 51 REF PART DESCRIPTION QTY SERIAL 1 REF ENGINE Isuzu diesel, 110 hp Turbo, 4.3L, 4 cylinder, 4 stroke... 1 Isuzu model # 4BG1TRW02 (not serviced), service items below, see NOTE SWITCH temperature (Isuzu # ) SENDER temperature (Isuzu # ) SWITCH oil pressure (Isuzu # ) SOLENOID engine stop (Isuzu # ) MANUAL Isuzu engine owners manual (Isuzu # IDE-6081) PARTS BOOK Isuzu engine (Isuzu # )... A/R MANUAL workshop (Isuzu # IDE-2280)... A/R DECAL emissions (Isuzu # EPA ENGINE FAMILY NO. 5SZXL04.3FTA, EC TYPE APPROVAL NO.: e9*97/68fa*00/000xx*3043*00) GASKET SET engine (Isuzu # )... A/R STUD engine mount (Isuzu # )... A/R RESISTOR control (Isuzu # )... A/R THERMOSTAT engine (Isuzu # )... A/R GASKET thermostat housing to pipe (Isuzu # )... A/R GASKET thermostat housing to block (Isuzu # )... A/R INJECTOR fuel (Isuzu # )... A/R INJECTOR TIP fuel (Isuzu # )... A/R WASHER injector (Isuzu # )... A/R WASHER feed pump banjo fitting (Isuzu # )... A/R ASSEMBLY feed pump (Isuzu # )... A/R HAND PRIMER fuel (Isuzu # )... A/R O-RING hand primer (Isuzu # )... A/R WATER SEDIMENTER fuel (Isuzu # )... A/R BOLT banjo (Isuzu # )... A/R FILTER SCREEN banjo bolt (Isuzu # )... A/R WASHER fuel, banjo bolt (Isuzu # )... A/R WATER PUMP engine, c/w gasket (Isuzu # )... A/R GASKET oil line return to turbo (Isuzu # )... A/R GASKET oil line return, drain (Isuzu # )... A/R TURBOCHARGER engine (Isuzu # )... A/R GASKET turbo (Isuzu # )... A/R GASKET turbo to adapter (Isuzu # )... A/R INJECTION PUMP (Isuzu # )... A/R WASHER injection pipe leak off (Isuzu # )... A/R WASHER injection pump oil supply (Isuzu # )... A/R WASHER oil line injection pump (Isuzu # )... A/R WASHER oil line pressure (Isuzu # )... A/R PLATE engine mount spacer, R/H only SENDER - tachometer SUPPORT - mount INSULATOR - front engine mounts SUPPORT engine, R/H rear INSULATOR - rear engine mounts SUPPORT engine, R/H rear SUPPORT engine, L/H rear CLAMP - exhaust... 1 NOTES: 1. The Isuzu engine repair parts listed under item 1 are available from your local Isuzu dealer using the Isuzu part numbers shown. If parts are not available from Isuzu, they may be ordered from MacDon using MacDon part numbers; however, Isuzu parts purchased from MacDon will cost more than if sourced from an Isuzu dealer. Warranty issues related to these parts should be submitted to your nearest Isuzu dealer. MacDon will not be responsible for the difference between Isuzu warranty coverage and the cost of the item purchased through MacDon Parts.

56 52 ENGINE ASSEMBLY ISUZU ENGINE TRACTOR UNITS

57 ENGINE ASSEMBLY ISUZU ENGINE TRACTOR UNITS 53 REF PART DESCRIPTION QTY SERIAL TUBE exhaust MUFFLER SHIELD starter FAN FILTER ELEMENT oil (Isuzu # ) FILTER ELEMENT fuel (Isuzu # ) STARTER with WIRING SHIELD ALTERNATOR Isuzu engine (Isuzu # ) BELT alternator/fan (Isuzu # ) (matched pair) SPACER fan mounting (Isuzu # ) GASKET exhaust... 1 A NUT lock, flange, 1/2 NC distorted thread B BOLT round head, square neck, 1/2 NC x 1-1/4 inch C NUT hex, M10 x 1.25 pitch D BOLT hex head, 1/2 NC x 1-3/4 inch E BOLT hex head, 1/2 NC x 1-1/4 inch F 7674 NUT jam, 3/4 NC G WASHER flat H BOLT 1/2 NC x 2-1/2 inch J NUT hex, 1/2 NC K WASHER lock L BOLT hex head, M10 x 1.25 pitch, 25 mm long M WASHER lock, M10 N BOLT 1/2 NC x 2-3/4 inch P 1045 WASHER flat Q WASHER lock, M8 R BOLT socket head, M8 x 1-1/4 inch S BOLT fan mounting (Isuzu # ) T WASHER flat, fan mounting (Isuzu # ) U STUD engine mount (Isuzu # ) V BOLT hex head, M10 x 1.25 x 30 mm long

58 54 ALTERNATOR MOUNTING CUMMINS ENGINE TRACTOR UNITS

59 ALTERNATOR MOUNTING CUMMINS ENGINE TRACTOR UNITS 55 REF PART DESCRIPTION QTY SERIAL 1 REF SUPPORT - alternator, Cummins # REF BOLT - hex head, M8 x 35 mm Cummins # REF SPACER - mounting, Cummins # BOLT hex head, M10 x 95 mm BRACE alternator, Cummins # BOLT - hex head, M8 x 45 mm BOLT - hex head, M10 x 25 mm ALTERNATOR Delco-Remy # PULLEY - alternator, Cummins # A WASHER flat, 13/16 inch ID 10 REF ALTERNATOR Cummins # (new) Delco-Remy # (new) Cummins # (reconditioned) e Cummins # (new)

60 56 ENGINE SUPERSTRUCTURE

61 ENGINE SUPERSTRUCTURE REF PART DESCRIPTION QTY SERIAL SHIELD - heat SHIELD heat SUPPORT - radiator, left - with decal SUPPORT - radiator, right COVER - engine, turbocharged diesel COVER - engine, naturally aspirated diesel COVER engine, turbocharged diesel COVER - engine, turbocharged diesel HANDLE hood opening ANGLE hood rail, L/H ANGLE hood rail, R/H ANGLE hood rail, L/H closing ANGLE hood rail, R/H closing SEAL closing angles WASHER steel/rubber, 3/ CLAMP ANGLE upper hood, closing SEAL hood closing HOOD & SCREEN ASSEMBLY includes screens (items 14 & 15), (was ) SCREEN R/H grill SCREEN L/H grill SPRING gas, includes items SPRING compression BALL stud CLIP ball stud SUPPORT hinge HINGE CABLE hood release SUPPORT top radiator SUPPORT hood seal PAN hood bottom (was ) SEAL lower hood STRAP clamp, hood seal SHROUD - fan, with seals, item 30, (N.A. only) SHROUD - fan, with seals item 30, (Turbo only)(may be subbed to ) SHROUD fan, with seals item 30, turbo SHROUD fan, with seals item 30, turbo SEAL foam, fan shroud LATCH hood SUPPORT hinge ROPE nylon, XX52 & XX52i Models only RETAINER rope storage, XX52 & XX52i Models only HANDLE rubber, XX52 & XX52i Models only INSERT handle, XX52 & XX52i Models only SEAL foam, rad support, vertical SEAL foam, rad support, horizontal SEAL foam, rad support, corner... 2 ~ f REF Indicates where hardware passes through frame or support member. A BOLT - round hd, sq. nk, 3/8 NC x 3/4 B NUT - lock, smth flng, 3/8 NC dist. thd. C BOLT - flange head, 3/8 NC x 3/4 D BOLT round hd, sq nk, 3/8 NC x 1 E BOLT - round hd, sq. nk, 3/8 NC x 3/4 F NUT hex, 5/16 NC G NUT serrated flange, 1/4 NC H BOLT rnd hd, sq. nk, 1/4 NC x 1-1/2 I BOLT hex head, 1/2 NC x 3/4 inch J BOLT M6 x 3/4 inch K NUT nylon insert, M6 x 1 inch L BOLT round hd, sq. nk, 1/4 NC x 3/4 M BOLT hex head, 5/16 NC x 3/4 N BOLT hex head, 5/16 NC x 3-1/2 57 P NUT flange lock, 5/8 11 NC R WASHER flat, 5/8 inch ID S WASHER lock, 5/16 inch ID T WASHER flat, 11/32 inch ID U BOLT flange head, 3/8 NC x 1 V WASHER flat, 3/8 inch ID W WASHER flat, 9/32 inch ID X NUT lock, smth flng, 5/16 NC dist thd. Y BOLT hex hd, 3/8 NC x 1-1/4 Z BOLT flg hd, 5/16 NC x 1 inch a NUT flange, 5/16 NC - MacDon 9250, Westward 9250, Prairie Star 4940, Premier 2940, Harvest Pro MacDon 9350/9352, Westward 9350/9352, Prairie Star 4950/4952, Premier 2950/2952, Harvest Pro 8150/ MacDon 9352i, Westward 9352i, Prairie Star 4952i, Premier 2952i, Harvest Pro 8152i - MacDon 9352c, Westward 9352c, Prairie Star 4952c, Premier 2952c, Harvest Pro 8152c

62 58 FUEL SYSTEM

63 FUEL SYSTEM 59 REF PART DESCRIPTION QTY SERIAL TANK - fuel PAD rubber, R/H bottom mount PAD rubber, R/H top mount PLATE R/H mount SENDER - fuel, with gasket GASKET - fuel sender CAP - fuel tank FITTING barbed HOSE - tank vent HOSE - to filter CLAMP - hose FILTER - fuel vent line, incl. hose (item 9) and two clamps (item 10) FITTING - barbed, 1/4 NPT x 3/16 hose (N.A. only) FITTING - barbed, 1/4 NPT x 5/16 hose... 1 see note HOSE - from engine return line... 1 see note HOSE from engine return line (N.A. only) BOWL sediment, with screen FITTING - barbed, 1/8 NPT x 5/16 hose FITTING barbed, 1/8 NPT x 3/8 hose HOSE - to engine fuel pump HOSE to engine fuel pump REF PANEL - see "Engine Superstructure" HOLDER hose (was 39272) SUPPORT tank breather VALVE ball, fuel shut off (XX52i only) SUPPORT throttle (XX52i only) CLAMP hose (XX52i only) FITTING barbed, 1/4 NPT x 3/8 hose (XX52i only) FITTING barbed, 3/8 NPT x 3/8 hose (XX52i only) HOSE from engine return line (XX52i only) HOSE suction, to engine fuel pump (XX52i only), (was ) FITTING nipple, 3/8 NPT (XX52i only) FILTER fuel, in-line (install in suction line) CLAMP hose CLAMP hose A BOLT round head, square neck, 1/2 NC x 1-1/2 inch B SCREW - machine, #10 NC x 3/4 inch C WASHER - lock, #10, 3/16 inch ID D BOLT round head, short square neck, 3/8 NC x 3/4 inch E NUT lock, smooth flange, 3/8 NC distorted thread - naturally aspirated engine only F NUT lock, smooth flange, 1/2 NC distorted thread G BOLT round head, square neck, 1/2 NC x 2-1/4 inch H WASHER flat, 17/32 inch ID J NUT hex, 1/2 NC K BOLT hex head, flange, 3/8 NC x 3/4 inch L BOLT round head, square neck, 3/8 NC x 3/4 inch M SCREW self tapping, 3/8 NC x 5/8 inch NOTES: 1.) Item 12 & 13 used on all XX50/XX52i tractors serial numbers. - used on XX40 tractors serial number & up.

64 60 ENGINE AIR INTAKE CUMMINS ENGINE TRACTOR UNITS NOTE: FOR ENGINE AIR INTAKE FOR CUMMINS TURBO UNITS WITH SN AND ABOVE, SEE PAGE 62/63 SN & BELOW

65 ENGINE AIR INTAKE CUMMINS ENGINE TRACTOR UNITS 61 REF PART DESCRIPTION QTY SERIAL NA / TURBO AIR CLEANER ELEMENTS ELEMENT filter, primary (outer), Turbo Engine ELEMENT filter, safety (inner), Turbo Engine ELEMENT - filter, primary (outer), Nat. Asp. Engine ELEMENT - filter, safety (inner), Nat. Asp. Engine CLEANER engine air, with filter elements, includes item 2, Turbo Engine NUT - wing VALVE vacuator, Turbo Engine BAND - mounting, with hardware, Turbo Engine CONNECTOR - 1/8 NPT FITTING - barbed, 1/8 NPT x 5/16 ID hose HOSE - to service indicator INDICATOR - service TUBE pre-cleaner, Turbo Engine HOSE - air intake to engine, Turbo Engine CLAMP hose... 1 / PRE-CLEANER - with clamp CLAMP - hose... 3 / HOSE hump, Turbo Engine HOSE ELBOW - 90, reducer, engine air intake, Turbo Engine REF COVER engine, Nat. Asp., See Engine Superstructure, page CLEANER - engine air, with filter elements, includes item 19, Nat. Asp. Engine BAND - mounting, with hardware, Nat. Asp. Engine HOSE - air intake to engine, Nat. Asp. Engine VALVE vacuator, Nat. Asp. Engine... 1 A NUT - serrated flange, 3/8 NC B NUT - lock, smooth flange, 3/8 NC distorted thread C BOLT - flange head, 3/8 NC x 3/4 inch D WASHER flat, 3/8 inch ID E BOLT round head, square neck, 5/16 NC x 1 inch F NUT flange, 5/16 NC, distorted thread

66 62 ENGINE AIR INTAKE ISUZU ENGINE TRACTOR UNITS & CUMMINS TRACTOR UNITS SN and ABOVE

67 ENGINE AIR INTAKE ISUZU ENGINE TRACTOR UNITS & CUMMINS TRACTOR UNITS SN and ABOVE 63 REF PART DESCRIPTION QTY SERIAL AIR CLEANER ELEMENTS: ELEMENT filter, primary (outer) ELEMENT filter, safety (inner)... 1 TURBO 1 REF COVER engine, see Engine Superstructure ADAPTER straight hump, ISUZU ADAPTER reducer hump, CUMMINS CLEANER - pipe CLEANER engine air, includes filter elements and item TUBE air intake, ISUZU TUBE air intake, CUMMINS ELBOW air intake, ISUZU ELBOW air intake, CUMMINS BAND air intake support HOSE air intake, moulded CLAMP - hose CLAMP hose, ISUZU CLAMP hose, CUMMINS CLAMP - hose FITTING elbow, barbed, INDICATOR - service FITTING hydraulic, female union HOSE indicator, ISUZU HOSE indicator, CUMMINS VALVE vacuator HOSE air intake, CUMMINS CLAMP HOSE, CUMMINS... 1 A BOLT - round head, square neck, 5/16 NC x 1 inch B NUT flange, 5/16 NC C BOLT - flange head, 3/8 NC x 3/4 inch D NUT lock, smooth flange, 3/8 NC, distorted thread E BOLT - flange head, 3/8 NC x 1 inch F WASHER flat, 13/32 inch ID

68 64 ENGINE COOLING CUMMINS ENGINE TRACTOR UNITS ISUZU ENGINE TRACTOR UNITS

69 ENGINE COOLING 65 REF PART DESCRIPTION QTY SERIAL CUMMINS ENGINE TRACTOR UNITS: RADIATOR, all serial # s for NA + serial # & below for turbo RADIATOR- turbo only CAP - radiator HOSE - upper rad, all serial # s for NA + serial # & below for turbo HOSE upper rad turbo only VALVE - drain HOSE - lower rad HOSE lower rad CLAMP - hose, all serial # s for NA + serial # & below for turbo CLAMP turbo only CLAMP - hose CLAMP turbo only TANK - coolant recovery, with cap and hose CAP vented, for coolant recovery tank CLIP - hose... 2 A BOLT - flange head, 3/8 NC x 3/4 inch B NUT - lock, smooth flange, 3/8 NC distorted thread ISUZU ENGINE TRACTOR UNITS: RADIATOR CAP - radiator TANK - coolant recovery, with cap and hose CAP vented, for coolant recovery tank HOSE lower radiator HOSE radiator adapter HOSE top radiator FITTING drain cock CLAMP hose CLIP - hose... 1 C BOLT - flange head, 3/8 NC x 3/4 inch D NUT - lock, smooth flange, 3/8 NC distorted thread

70 66 AIR INTAKE SCREEN CLEANER

71 AIR INTAKE SCREEN CLEANER 67 REF PART DESCRIPTION QTY SERIAL CAP - plastic PLUG - plastic (for screen holes), Standard Air Intake Screen only PLATE cover, see note (1) HOUSING - duct, includes item SEAL - foam, housing to screen BAR - mounting DUCT plastic PIN duct BUSHING - plastic COUPLING CLEANER - seal SEAL cleaner MOTOR - electric CAP vinyl O-ring STOP - motor MOULDING - edge HOSE air, L/H CLAMP - hose SEAL - sponge HOSE elbow SUPPORT outer cleaner, R/H SUPPORT outer cleaner, L/H HARNESS screen cleaner GROMMET harness REF PAN hood bottom, See Engine Superstructure, page CLAMP hose HOSE air, R/H FASTENER plastic tie... 2 A BOLT flange, hex head, 3/8 NC B NUT - lock, smooth flange, 3/8 NC distorted thread C BOLT - round head, square neck, 3/8 NC x 3/4 inch D NUT - serrated flange, 3/8 NC E SCREW - hex washer head, 5/16 NC x 1/2 inch, thread cutting F SCREW - set, Allan socket head, 3/8 NC x 5/8 inch G WASHER - lock, #8 H SCREW - machine, round slotted head, #8 NC x 5/16 inch J NUT jam, 3/8 NC ~ f REF Indicates where hardware passes through frame member. NOTES: 1.) Used to plug hose routing holes

72 68 HEADER DRIVE

73 HEADER DRIVE 69 REF PART DESCRIPTION QTY SERIAL FITTING - reducer bushing, 3/8 NPT x 1/8 NPT CLAMP - hose VALVE - relief FASTENER - plastic tie WASHER - flat GUIDE - belt, lower FITTING elbow, 90 barbed elbow, 3/8 NPT x 5/8 I.D. hose BUSHING - plastic HOSE - hydraulic, bevel gear box to relief valve... 1 (see pg. 68, HOSE hydraulic, bevel gear box to relief valve... 1 for box desc.) BELT - header drive INSULATOR - rubber PULLEY - idler WASHER - flat GUARD - front pulley, with decals REF PULLEY ASSEMBLY - see "Header Drive Pulley", page REF BEVEL GEARBOX - see page REF DRIVELINE - see page GUIDE - belt, upper RETAINER - belt ARM - idler PIVOT - idler CYLINDER - header clutch, complete SHAFT - header clutch cylinder TUBE - header clutch cylinder SEAL - oil, outer (for header clutch cylinder) SEAL - oil, inner (for header clutch cylinder) RING - retaining, internal (for header clutch cylinder) RESTRICTOR - hydraulic O-RING - (for header clutch cylinder) SPRING - extension PIN - roll, 3/8 x 1 inch PULLEY - driver, Turbo Diesel (was 42153) PULLEY - driver, Naturally Aspirated Diesel Engine (was 45522) BUSHING - split taper, with outer key KEY - 5/16 square x 2 inch SUPPORT - switch SWITCH - header drive belt (was 45234) SPACER COVER - gearbox shaft access SHIM - header pulley alignment... A/R FITTING - lube REF SUPPORT - fan shield, see page BELT - header drive GUARD front pulley, with decals GUIDE belt, upper... 1 A NUT - hex, 5/8 NC B SCREW - hex washer head, 5/16 x 1/2 C NUT - lock, 5/8 NC dist. thread D NUT - lock, smth flange, 1/2 NC dist. Thd. E WASHER - flat, 21/32 inch I.D. F WASHER - lock, 3/8 inch ID G WASHER - lock, 1/2 inch ID H WASHER - lock, 5/8 inch ID I BOLT - rnd hd, sq. nk, 3/8 NC x 3/4 J BOLT - hex head, 3/8 NC x 1 inch K NUT - serrated flange, 1/2 NC L NUT - serrated flange, 3/8 NC M BOLT - hex hd, 5/16 NC x 1-1/4 in. N BOLT hex hd, 1/2 NC x 1-1/4 inch O BOLT - rnd hd, sq. nk, 1/2 NC x 1 in. P BOLT hex hd, 3/8 NC x 1-1/2 inch Q BOLT hex hd, 5/8 NC x 2-1/2 inch R BOLT - hex hd, 1/2 NC x 2 1/2 inch S BOLT- rnd hd, short sq. nk, 3/8 NC x 3/4 in T BOLT - hex head, 3/8 NC x 4-1/2 inch U NUT - lock, smooth flange, 3/8 NC dist.thd. V BOLT - hex head, 5/8 NC x 4-1/2 inch W NUT - hex, 3/8 NC X WASHER - flat, 13/32 inch I.D. Y BOLT - hex head, 1/2 NC x 4 inch Z BOLT - flange head, 3/8 NC x 3/4 inch a BOLT round hd, sq. neck, 3/8 NC x 1 ~ f REF Indicates where hdw passes through frame member. - MacDon 9250/9350, Westward 9250/9350, Prairie Star 4940/4950, Premier 2940/2950, Harvest Pro 8140/ MacDon 9352/9352i/9352c, Westward 9352/9352i/9352c, Prairie Star 4952/4952i/4952c, Premier 2952/2952i/2952c, Harvest Pro 8152/8152i/8152c

74 70 Header Drive - BEVEL GEARBOX Prior to 2002 Production * * NOTE: The change-over from this gearbox to the one shown on page 73 occurred in stages over a period extending from the end of 2001 Production through early 2002 Production. For machines built in this period, identify gearbox and order service parts for the appropriate unit. This unit has a bolt-on extension tube (item17) while the newer gearbox has a one-piece cast housing with cooling fins. The newer box (167299) plus pulley (item 27 on page 69) replaces the prior one (45877) as a complete unit only. See note regarding machining of existing pulley on next page.

75 Header Drive - BEVEL GEARBOX Prior to 2002 Production * 71 REF PART DESCRIPTION QTY SERIAL * DRIVE - bevel gearbox, complete - includes items 2 to see NOTE BUSHING - rubber GEAR - set SEAL - output, extension end SCREW - special, M14 x 45 mm SHAFT - output KEY SHAFT - input SEAL - input FLANGE - bearing BEARING - tapered roller, cup and cone WASHER - blank SHIM KIT SCREW - hex socket head, M12 x 30 mm BOLT - hex head, M12 x 25 mm TUBE - extension HOUSING O-RING - gearbox to tandem pump... 1

76 72 Header Drive - BEVEL GEARBOX: 2002 Production and up * NOTES: 1. For units with V2 gearbox, to upgrade input shaft bearing (engine end), order kit This kit consists of items marked ** on page Required for V2 & V3 boxes only, discard spacer if you have V4 box. 3. Version Identification: Version 2 (V2): Date code L05 or prior Version 3 (V3) :Comer Code Date code A06 Note: Earlier boxes (Date code L05 or prior) may have been upgraded to V3 box if the end cap housing for input shaft has the new marking. See MD Service Bulletin 0701_B. Version 4 (V4): Comer Code Date Code D 06 and higher. For more information on identifying gearbox versions up to V4 see MD Service Bulletin 0701_B. Version 5 (V5): Comer Code For units with V2 gearbox. Confirm number on cover casting (item 19), if order kit includes items ** on page Required on V2 & V3 gearboxes if kit has been installed. 6. Required on V2 & V3 gearboxes if shaft has been installed. * NOTE: The change-over to this gearbox from the one shown on page 71 occurred in stages over a period extending from the end of 2001 Production through early 2002 Production. For machines built in this period, identify gearbox and order service parts for the appropriate unit. This unit has a one-piece cast housing with cooling fins while the prior gearbox has a bolt-on extension tube for the output shaft. NOTE: The newer box (167299) plus pulley (item 27 on page 69) replaces the prior one (45877) as a complete unit only. An alternative to purchasing a new pulley (item 27 on page 69) is to machine your existing pulley to a larger bore. Note that a machine lathe is required to ensure concentricity and balance. Severe vibration problems could result if pulley is machined improperly. For more information see MD Service Bulletin 0302.

77 Header Drive - BEVEL GEARBOX: 2002 Production and up * 73 REF PART DESCRIPTION Version 2, 3, 4, 5 Qty s (See Note 3) V2 V3 V4 V DRIVE - bevel gearbox, complete see note DRIVE - bevel gearbox, complete - see note DRIVE - bevel gearbox, complete - see note DRIVE - bevel gearbox, complete - see note CAP housing SHIM KIT base size 72 mm O.D, input shaft (qty. 2 for V2 box) BEARING tapered roller, cup & cone (input shaft) BEARING tapered roller, cup & cone (input shaft) BEARING ball, cylindrical SHAFT input, includes item 30 ( see note 2) SHAFT INPUT RING retaining, external RING retaining, internal GEAR set, includes two matched bevel gears, includes shim kit GEAR SET, includes two matched bevel gears... 1 NOTE: Do not mix gears from different sets SHIM KIT base size 40 mm bore, output shaft SHIM KIT base size 40 mm bore, output shaft SPACER BEARING tapered roller, cup & cone (output shaft) HOUSING gearbox, cast HOUSING gearbox, cast PLUG magnetic, 3/8 GAS SHAFT output, repair kit includes shaft, gear set, shim kit & hardware SHAFT output NUT special, M SEAL double lip, output shaft BUSHING rubber SEAL double lip, input shaft... 1 ** SEAL double lip, input shaft SEAL double lip, input shaft BOLT hex socket head, M12 x 25 mm ** COVER input shaft bearing flange (for V2 box, order kit ) see note COVER inner RING retaining, external CAP dust RING retaining, internal O-RING - gearbox to tandem pump ** BEARING taper roller, cup & cone (input shaft, engine end) BEARING double row ball ** SHIM KIT input shaft, engine end REF ELBOW barbed, see Header Drive, page TOOL for output shaft nut (item 14)... A/R A/R A/R A/R WASHER blank, see note SCREW special, M14 x 45, see note SPACER input shaft, see note 2, SHIM cover NUT M35 x BOLT hex socket head, M8 x 20 mm O-RING cover COVER outer PIN DOWEL INPUT SHAFT ASSEMBLY to convert V4 gearbox to V NOTES: See facing page.

78 74 DRIVELINE (Engine to Bevel Gearbox)

79 DRIVELINE (Engine to Bevel Gearbox) 75 REF PART DESCRIPTION QTY SERIAL FAN - plastic SHIM - locking DRIVELINE - engine, complete with end yokes (see note 1) DRIVELINE - engine, complete with end yokes (see note 2) JOINT & SHAFT HALF, assembly (see notes 2, 3) TELESCOPING JOINT, assembly (see notes 2, 3) SEAL, telescoping joint (see notes 2, 3) PLATE - adapter, diesel engine DISC - fan mount SHIELD - fan, with decal CROSS & BEARING KIT YOKE - engine end YOKE - gearbox end, spline bore, with fan mounting plate YOKE - gearbox end, spline bore (see notes 2, 3) FITTING - lube, 45, 1/4 NF SUPPORT - fan shield SUPPORT - driveline U-BOLT WASHER - square... 2 A NUT - hex, 3/8 NF (phosphate coated) D BOLT - hex head, 3/8 NC x 3/4 inch E BOLT - hex head, 3/8 NF x 1 inch (phosphate coated) F WASHER - lock, 3/8 inch ID G NUT - serrated flange lock, 3/8 NC H BOLT - round head, square neck, 3/8 NC x 3/4 inch J NUT - lock, smooth flange, 3/8 NC distorted thread K BOLT - hex head, 3/8 NC x 1 inch L BOLT round head, square neck, 3/8 NC x 1 inch. Notes: 1. Use driveline to service units with a bevel gearbox with bolt-on extension tube (see page 70, 71) 2. Use driveline to service units with a bevel gearbox with a one-piece cast housing with cooling fins (see page 72, 73) 3. Used on driveline only.

80 76 HEADER DRIVE PULLEY REF PART DESCRIPTION QTY SERIAL PULLEY - with cups and rings (items 2 and 3) CUP - bearing RING - retaining, internal SUPPORT - with shaft CONE - bearing, with seal WASHER - flat, hardened NUT - slotted hex, 3/4 NF PIN - cotter, 1/8 x 1 inch FITTING - lube SUPPORT with shaft... 1 A BOLT - hex head, 3/8 NC x 1 inch C WASHER - lock, 3/8 inch ID - MacDon 9250/9350, Westward 9250/9350, Prairie Star 4940/4950, Premier 2940/2950, Harvest Pro 8140/ MD 9352/9352i/9352c, WP 9352/9352i/9352c, PS 4952/4952i/4952c, PR 2952/2952i/2952c, HP8152/8152i/8152c

81 9000 Series Tractor to 900 Series Headers DRIVELINE SERIAL and below 77 REF PART DESCRIPTION QTY SERIAL YOKE - flange CROSS & BEARING KIT NSS YOKE & SHAFT (order 44987) SHIELD - outer, with decal BEARING - shield, consists of two halves (Walterscheid) BEARING KIT - shield (Weasler) SHIELD - inner SUPPORT - shield (Walterscheid) NSS YOKE & TUBE - (order 43707) YOKE - spline bore, 1 3/8 x 21 teeth, with slide collar YOKE - spline bore, 1 3/8 x 21 teeth, clamp type... OPT JOINT ASSEMBLY - male half, includes items 1,2,3,4, JOINT ASSEMBLY - female half, includes items 2,5,6,8, DRIVELINE - complete, includes items 10 and NSS Not Serviced Separately

82 Series Tractor to 900 Series Headers DRIVELINE SERIAL and above REF PART DESCRIPTION QTY SERIAL YOKE spline bore, header end CROSS JOURNAL ASSEMBLY, includes cir-clips and grease fitting FITTING grease, for cross, M8 x GREASE SYSTEM COVER YOKE flange, tractor end CHAIN anti-rotation SHIELD HALF outer SHIELD HALF inner HALF SHAFT header end, includes yoke, shaft & shields HALF SHAFT tractor end, includes yoke, shaft & shields SCREW self tapping RETAINER plastic ring, outer shield RETAINER plastic ring, inner shield... 1 ** DRIVELINE - complete, includes all above items... 1

83 NEUTRAL INTERLOCK & PINTLE ARMS 79 REF PART DESCRIPTION QTY SERIAL LOCK - neutral ARM - pintle, with bushing (item 3) BUSHING - rubber, used with item REF PUMP - piston, see "Hydraulics: Triple Pump", page BUSHING - plastic SUPPORT gearbox, rear (was ) SUPPORT front lock SUPPORT c/w bushing, item BUSHING - rubber, used with item WASHER flat (was 25900) MOUNT - switch SWITCH - neutral SWITCH neutral SPRING - extension CABLE ASSEMBLY REF DRIVE - gear, see "Bevel Gearbox", page A BOLT - hex head, 13/8 NC x 1 inch B WASHER - lock, 1/2 inch ID C BOLT hex head, 1/2 NC x 1-1/2 inch D WASHER lock, 3/8 inch ID E SETSCREW - square head, flat point, 3/8 NC x 1-3/4 inch F WASHER flat, 13/32 inch ID G NUT - hex, 1/2 NC H NUT - lock, 1/2 NC distorted thread J WASHER - flat, 17/32 inch ID K BOLT - round head, square neck, 3/8 NC x 1 inch L BOLT - hex head, 1/2 NC x 3 inch, grade 8 M NUT - hex jam, 1/2 NC N BOLT - hex head, 3/8 NC x 1-1/2 inch P NUT - hex, 3/8 NC R NUT - lock, smooth flange, 3/8 NC distorted thread S BOLT hex head, 1/2 NC x 3-1/4 inch T WASHER flat, 21/32 inch ID ~ f REF Indicates where hardware passes through frame member

84 80 STEERING & GROUND SPEED

85 STEERING & GROUND SPEED 81 REF PART DESCRIPTION QTY SERIAL ARM - steering, with bushing (item 2) BUSHING - rubber PIVOT - steering CARRIER - steering, with bushing (item 2) BUSHING - plastic WASHER - flat SUPPORT - steering arm BAR - control, left, with bushing (item 2) (to front pintle arm) BAR - control, right, with bushing (item 2) (to rear pintle arm) CHAIN - steering INSULATOR - rubber WASHER - flat... see note (1) 14 REF LEVER - ground speed, see "Ground Speed Lever", page REF SHAFT - steering, see "Steering Column", page REF PINTLE ARM - see "Neutral Interlock & Pintle Arms", page BAR - control, ground speed PAD friction SPRING - compression... 1 A WASHER - flat, 17/32 inch ID B BOLT - round head, square neck, 1/2 NC x 1-1/2 inch C BOLT - hex head, 1/2 NC x 3-1/2 inch D NUT - hex, 1/2 NC E NUT - lock, 1/2 NC distorted thread F WASHER - lock, 1/2 inch ID G BOLT - hex head, 1/2 NC x 2-1/4 inch H BOLT - hex head, 1/2 NC x 4 inch J PIN - cotter, 3/16 x 1-1/4 inch K BOLT - round head, square neck, 1/2 NC x 5 inch ~ f REF Indicates where hardware passes through frame member. NOTES: (1) - Quantity of item 13 varies as required for shimming. Nominal quantity is 3 L/H, R/H).

86 82 HYDRAULICS: HEADER DRIVE

87 HYDRAULICS: HEADER DRIVE 83 REF PART DESCRIPTION QTY SERIAL VALVE - header drive block, includes items SEAL KIT repairs one cartridge in header drive valve block BLOCK only FITTING - adapter, 7/8 O-ring x 5/8 tube FITTING - tee, 1-1/16 O-ring x 3/4 tube x 3/4 tube HOSE - hydraulic, pressure to female coupler HOSE - hydraulic, return from male coupler FITTING - connector WASHER - dished COUPLER - quick disconnect, female, 1/2 NPT O-RING - for coupler COUPLER - quick disconnect, male, 1/2 NPT HOLDER - hose FITTING - connector HOSE - pressure to male coupler (was 47009) FITTING - elbow HOSE - hydraulic, pressure - pump to block HOSE - hydraulic, pressure - to male coupler HOSE - hydraulic, return - coupler to filter LINE - hydraulic, return - block to filter FITTING - tee OIL FILTER ELEMENT spin-on, see note 1 re: substitution OIL FILTER ASSEMBLY head & element HOSE - hydraulic, return - filter to tank FITTING - connector VALVE - check REF PUMP - hydraulic, see page VALVE - N.C., header drive block VALVE - P.D. relief, header drive block (stamped I.D. #2155) FLOW CONTROL, header drive block COLLAR flow control SETSCREW - for flow control PIN roll SEAL crush ring VALVE - shuttle, header drive block VALVE - regulator, header drive block COIL - DS, 12VDC, header drive block (was 45104) FASTENER - plastic tie CLAMP hose HOSE hydraulic suction HOSE hydraulic, case drain to tank FITTING connector (8-10) FITTING elbow, barbed insert, FASTENER hose clamp FASTENER plastic tie TOOL for disassembly of flow control, item FITTING hydraulic, elbow, 45 male VALVE reel conveyor drive block PLATE valve block mounting HOSE hydraulic HOSE hydraulic... 1 A BOLT - rnd hd, sq nk, 3/8 NC x 3-1/2 B BOLT - flange head, 1/4 NC x 3/4 inch C NUT - lock, smth flg, 3/8 NC dist thread D NUT - serrated flange, 3/8 NC E NUT - hex jam, 1/2 NF F BOLT rnd hd, sht sq nk, 3/8 NC x 3/4 G BOLT hex head, 3/8 NC x 1-1/2 inch H BOLT rnd hd, sq nk, 3/8 NC x 1 inch NOTES:1.) Pressure rating on MacDon filter element is not adequate for this application.

88 84 HYDRAULICS: CYLINDER CONTROL NOTE: For units with integral brakes which plumb into this valve block (item 1) see page 114 for details.

89 HYDRAULICS: CYLINDER CONTROL 85 REF PART DESCRIPTION QTY SERIAL VALVE - cylinder control block, with reel lift - includes items SEAL KIT repairs one cartridge in cylinder control valve block BLOCK only FITTING - connector FITTING - connector FITTING - elbow HOSE - pressure, pump to valve HOSE - valve to left header lift cylinder HOSE - left header lift cylinder to right header lift cylinder HOSE - valve to right header lift cylinder HOSE - valve to reel lift coupler FITTING - connector WASHER - dished COUPLER - quick disconnect, male (reel lift) CAP - coupler FITTING connector (10-10) GROMMET - hose protector HOSE - valve to tank HOLDER - hose HOSE - valve to oil cooler HOSE - valve to header clutch cylinder FASTENER - cable tie FITTING connector (4-6) GROMMET hose holder FITTING - connector OIL FILTER ELEMENT spin-on (1-1/2 thread) OIL FILTER ASSEMBLY head & element OIL FILTER ELEMENT spin-on (1-3/8 thread) OIL FILTER ASSEMBLY head & element SWITCH - oil pressure (40 psi), single-speed units SWITCH - oil pressure (150 psi), two-speed units HOSE - oil cooler to filter (150 psi) REF HOSE see Hydraulics: Header Drive, page HOSE - filter to tank HOSE - pump charge pressure FITTING adapter (12-12) CYLINDER - left, header lift - 3" bore SEAL KIT - for cylinder see page 88 for kit contents COOLER - oil - JIC fittings LATCH - cooler mount REF CONDENSER - see "Air Conditioning", page REF CYLINDER - header clutch, see "Header Drive", page REF PUMP - see page SHIELD - valve CYLINDER - right, header lift, 2-1/2" bore SEAL KIT - for cylinder see page 89 for kit contents

90 86 HYDRAULICS: CYLINDER CONTROL NOTE: For units with integral brakes which plumb into this valve block (item 1) see page 114 for details.

91 HYDRAULICS: CYLINDER CONTROL 87 REF PART DESCRIPTION QTY SERIAL VALVE - N.C. (ports S-3 & S-5) VALVE - relief VALVE - 3W 2P (port S-2) VALVE - 4W 2P (port S-4) VALVE - N.O. (port S-1) VALVE check valve COIL - DS, 12VDC (was 45104) NUT - special, machined RESTRICTOR - flow, header clutch cylinder RESTRICTOR - flow, to slow rate of 960/962/972 Headers lift and drop (install in bottom port of item 31) SUPPORT coolers REF GUARD coolers, see Air Conditioning Engine Group, page FITTING run tee CAP 1/2 tube x 1/8 NPT SWITCH header/brake MacDon 9352i/9352c, Westward 9352i/9352ic, Prairie Star 4952i/4952c, Premier 2952i/2952c Harvest Pro 8152i/8152c A BOLT - flange head, 3/8 NC x 3/4 inch B BOLT - round head, square neck, 3/8 NC x 1-1/2 inch C NUT - lock, smooth flange, 3/8 NC distorted thread D BOLT - flange head, 5/16 NC x 3/4 inch BOLT flange head, 3/8 NC x ¾ inch E BOLT - round head, square neck, 3/8 NC x 3/4 inch F NUT - hex jam, 1/2 NF G NUT wing, 3/8 NC H BOLT round head, square neck, 3/8 NC x 1 inch

92 88 Header Lift Cylinder 3.0" BORE SEAL KIT REF PART DESCRIPTION QTY SERIAL SEAL KIT - 3" bore, for header lift cylinder Includes the following: 3 O-RING BN - 3" OD x 2-5/8" ID O-RING BN - 1-1/8 OD x 7/8" ID O-RING BN - 3" OD x 2-3/4" ID BU WASHER - 3" OD x 2-3/4" ID U CUP, L B - 2" OD x 1-5/8" ID x 3/8" long WIPER MT - 1-5/8" ID x 2-1/8 OD x 5/16" long... 1

93 Header Lift Cylinder 2.5" BORE SEAL KIT 89 REF PART DESCRIPTION QTY SERIAL SEAL KIT - 2.5" bore, for header lift cylinder Includes the following: 3 BU WASHER - 2-1/2" OD x 2-1/8" ID O-RING BN - 2-1/2" OD x 2-1/8" ID O-RING BN - 1-1/8 OD x 7/8" ID O-RING BN - 2-1/2" OD x 2-1/4" ID BU WASHER - 2-1/2" OD x 2-1/4" ID U CUP, L B - 2" OD x 1-5/8" ID x 3/8" long WIPER MT 1-5/8 ID x 2-1/8 OD x 5/16 long... 1

94 90 HYDRAULICS: TRACTION DRIVE

95 HYDRAULICS: TRACTION DRIVE 91 REF PART DESCRIPTION QTY SERIAL NA / TURBO FITTING - elbow, 3/4 tube x 1-1/16 O-ring O-RING - for 1-1/16 fitting HOSE - hydraulic - to left wheel motor, rear port (single speed units) HOSE - hydraulic - to left wheel motor, rear port (2 speed units) HOSE - hydraulic - to left wheel motor, front port (single speed units) HOSE - hydraulic - to left wheel motor, front port (2 speed units) FITTING elbow, PAD - foam HOSE - hydraulic - to right wheel motor, rear port (single speed units) HOSE hydraulic to right wheel motor, rear port (2 speed units) HOSE - hydraulic, case drain from motors (L/H motor) FITTING - tee REF FITTING motor pressure, see Wheel Motor Assembly FITTING - tee FITTING elbow, #4 JIC fitting SWITCH supercharge oil pressure, 2 speed units SWITCH supercharge oil pressure, single speed units HOSE - hydraulic - to right wheel motor, front port (single speed units) HOSE hydraulic to right wheel motor, front port (2 speed units) TANK hydraulic, with decal FITTING - barbed insert, 45, 1-5/8 O-ring HOSE - hydraulic, suction CLAMP - hose HOSE - filler to tank CAP - dipstick STRAINER PLUG - magnetic, with O-ring (44209) SUPPORT - left SUPPORT - right RETAINER - tank mount STRIP - lower, tank mount STRIP - upper, tank mount FITTING - elbow HOSE - vent CLAMP - hose BREATHER HOSE - breather intake FASTENER - plastic tie, 7-1/2 inch REF PUMP - see page FASTENER - plastic tie, 14-1/2 inch HOSE hyd, pump case drain to tank FITTING connector (8-10) MOUNT hose BAR hose mount MANIFOLD supercharge, 2 speed MANIFOLD supercharge, single speed HOSE control valve, tee (2 speed units) HOSE servometer, tee (2 speed units) FITTING connector (2 speed units) FITTING adapter (2 speed units) FITTING connector FITTING elbow, #6 JIC fitting FITTING connector (8-12)... 2 A NUT - lock, smooth flange, 3/8 NC distorted thread B BOLT - round head, square neck, 3/8 NC x 1 inch C BOLT - round head, square neck, 3/8 NC x 1-1/2 inch

96 92 HYDRAULICS: TRIPLE PUMP

97 HYDRAULICS: TRIPLE PUMP 93 REF PART DESCRIPTION QTY SERIAL NOTE: Piston pump component quantities are per pump assembly. * PUMP triple, complete (Eaton #78364-RBU-02)... 1 (was , Eaton #78364-RBH-02) 1 HOUSING sub assembly PLATE cover, sub assembly SCREW - cap WASHER CUP - bearing CAMPLATE sub assembly (front) CAMPLATE sub assembly (rear) KIT - shim... A/R PLATE cover, sub assembly with seal... A/R SEAL for cover plate SHAFT drive, front SHAFT drive, rear (for pump ) ** SHAFT drive, rear (for pump ) ** RING - retaining RACE - thrust BEARING - thrust WASHER SEAL shaft, viton RING - retaining INSERT cam plate KIT rotating sub assembly MANIFOLD center sub assembly VALVE relief sub assembly PLATE - valve (R/H front) PLATE valve (R/H rear) PIN - dowel GASKET housing, front & rear O-RING SCREW - cap HOUSING sub assembly, (rear) REF DOUBLE GEAR PUMP SUB ASSEMBLY see page PLUG LABEL identification PLUG sub assembly... 1 * SEAL KIT incl. all items marked +, for pump & ** For units with serial numbers in the range not specified above, ie to , identify your pump using the Eaton number listed at the top of this page and order the corresponding shaft.

98 94 HYDRAULICS: DOUBLE GEAR PUMP

99 HYDRAULICS: DOUBLE GEAR PUMP 95 REF PART DESCRIPTION QTY SERIAL * PUMP - double gear, part of Triple Pump ** Eaton Production #26513-R01 / Eaton Service # PUMP - double gear, part of Triple Pump ** Eaton Production #26513-R02 / Eaton Service # For other triple pump components, see page BACKPLATE BODY - rear BODY - front DRIVE GEAR - front IDLER GEAR - front IDLER GEAR - rear GASKET pressure balance PLATE wear SEAL pressure balance SCREW cap O-RING ADAPTOR PLATE KEY PLUG DRIVE GEAR slip fit, rear WASHER O-RING... 1 * SEAL KIT incl. all items marked +, for pump & ** For units with serial numbers in the range not specified above, ie to , identify your pump using the Eaton numbers listed at the top of this page. The Eaton production number, service number, or both will be stamped into the pump housing.

100 96 HYDRAULICS: TWO-SPEED WHEEL MOTOR

101 HYDRAULICS: TWO-SPEED WHEEL MOTOR 97 REF PART DESCRIPTION QTY SERIAL MOTOR - wheel, hydraulic piston type, complete VALVE PLATE motor SWASHPLATE ASSEMBLY - variable BEARING - journal PIN - spring SCREW BEARING - ball RING RING internal retaining PIN - spring PIN BEARING - sleeve GASKET front cover PIN - straight BEARING - needle PLUG O-RING (was 49744) SPRING - servo GASKET - servo SCREW RING - bearing PIN - slotted WASHER - support SEAL - lip SHAFT 13 tooth, splined STOP PISTON ASSEMBLY - servo COVER - servo PLUG O-RING PLUG O-RING PLUG PLUG SPRING - compression SPRING GUIDE SHUTTLE SPOOL PLUG SHIM KIT O-RING SPRING - compression POPPET CYLINDER BLOCK ASSEMBLY, includes items CYLINDER BLOCK PISTON ASSEMBLY SPRING cylinder block WASHER SLIPPER GUIDE RING retaining WASHER HOLD DOWN slipper retainer GUIDE retainer PIN slipper hold down PISTON RING KIT servo... 1

102 98 TWO SPEED DRIVE: WHEEL MOTOR ASSEMBLY SEE NOTE 2, NEXT PAGE

103 TWO SPEED DRIVE: WHEEL MOTOR ASSEMBLY 99 REF PART DESCRIPTION QTY SERIAL 1 REF DRIVE - power wheel, see page 105 or REF DRIVE power hub, see Model RR Power Hub, page see Note O-RING - power wheel to motor seal REF MOTOR - hydraulic, see page FITTING - elbow, 1-1/16 O-ring x 3/4 inch tube O-RING - for item FITTING elbow O-RING for item SPACER final drive BRACKET speed sensor KIT speedometer sender, includes hardware A & C (see Note 1) MAGNET PLATE cap FITTING adapter FITTING elbow O-RING for item REF SUPPORT brake band, see Brakes, page BRACKET speed sensor GUARD speed sensor SPACER final drive BRACKET speed sensor... 1 A NUT nylon, jam, 1/2 NC B BOLT hex head, 5/8 NC x 2-1/4 inch BOLT hex head, 5/8 NF x 2-1/4 inch, Grade C WASHER flat, 17/32 inch ID (see Note 1) D BOLT hex head, 5/8 NC x 1-3/4 inch E NUT lock, 5/8 NC F WASHER lock, 5/8 inch ID WASHER hardened, 5/8 inch ID G WASHER - lock, 1/2 inch ID J BOLT flange head, 5/16 NC x 1/2 inch K BOLT hex socket head, 1/2 NC x 1-3/4 inch L BOLT hex head, 5/8 NC x 2 inch M SCREW hex head, self tapping, 3/8 NC x 5/8 inch N BOLT hex head, 5/8 NF x 2-1/2 inch, grade 8 NOTES: 1. For & tractors, flat washers included with speedometer sender kit are NOT used. 2. For tractors, parts orders for the Model RR Power Hub shown here may have been substituted with kit consisting of Auburn Power Wheel and related bracketry. For repair parts specific to this kit, see pages 99A & 99B. For internal repair parts for Auburn Power Wheel see pages 109A & 109B. - MacDon 9250/9350, Westward 9250/9350, Prairie Star 4940/4950, Premier 2940/2950, Harvest Pro 8140/ MacDon 9352, Westward 9352, Prairie Star 4952, Premier 2952, Harvest Pro MacDon 9352i/9352c, Westward 9352i/9352ic, Prairie Star 4952i/4952c, Premier 2952i/2952c Harvest Pro 8152i/8152c

104 99 A TWO SPEED DRIVE: WHEEL MOTOR ASSEMBLY AUBURN REPLACEMENT WHEEL FOR RR POWER HUB

105 TWO SPEED DRIVE: WHEEL MOTOR ASSEMBLY AUBURN REPLACEMENT WHEEL FOR RR POWER HUB 99 B REF PART DESCRIPTION QTY SERIAL KIT - AUBURN REPLACEMENT WHEEL FOR RR POWER HUB Includes all items marked 1 REF DRIVE Auburn Power Wheel, see pages 109A & 109B for repair parts O-RING - power wheel to motor seal REF MOTOR - hydraulic, see page FITTING - elbow, 1-1/16 O-ring x 1 inch tube O-RING - for item FITTING elbow O-RING for item SPACER final drive (qty 1 included in kit; 2 req d per wheel use existing) BRACKET speed sensor KIT speedometer sender, includes hardware A MAGNET PLATE cap FITTING adapter FITTING elbow O-RING for item GUARD speed sensor... 1 A NUT nylon, jam, 1/2 NC B BOLT hex head, 5/8 NC x 2-1/2 inch... 2 C NUT lock, 5/8 NC... 2 D BOLT hex socket head, 1/2 NC x 2 inch... 2 E WASHER - lock, 1/2 inch ID... 2 F BOLT hex head, 5/8 NC x 3 inch... 6 G WASHER hardened, 5/8 inch ID... 6 J BOLT flange head, 5/16 NC x 1/2 inch M SCREW hex head, self tapping, 3/8 NC x 5/8 inch

106 100 HYDRAULICS: SINGLE SPEED WHEEL MOTOR REF PART DESCRIPTION QTY SERIAL MOTOR hydraulic, single speed SEAL KIT hydraulic motor, includes items marked RING retaining SEAL motor shaft RING retaining SHAFT drive, 13 tooth spline,.875 inch shaft BEARING needle O-RING - motor, internal BACKPLATE ASSEMBLY BEARING needle... 1

107 SINGLE SPEED DRIVE: WHEEL MOTOR ASSEMBLY 101 REF PART DESCRIPTION QTY SERIAL 1 REF DRIVE - power wheel, see page O-RING - power wheel to motor seal REF MOTOR hydraulic, single speed, see page FITTING - elbow, 1-5/16 O-ring x 1 inch tube O-RING - for 1-5/16 fitting FITTING - adapter, 3/4 O-ring x 3/8 inch tube O-RING - for 3/4 fitting FITTING - 45 elbow, 3/8 inch tube SPACER final drive BRACKET speed sensor KIT speedometer sender (was ) MAGNET PLATE cap... 4 A BOLT - hex head, 5/16 NC x 3/4 inch B WASHER lock, 5/16 inch ID C WASHER flat, 17/32 inch ID D BOLT hex head, 5/8 NC x 1-1/2 inch E BOLT - hex head, 1/2 NC x 1-1/4 inch F NUT lock, 5/8 NC G WASHER - lock, 1/2 inch ID H BOLT hex head, 5/8 NC x 2 inch BOLT hex head, 5/8 NF x 2 inch, Grade J NUT nylon, jam, 1/2 NC K WASHER - lock, 5/8 inch ID WASHER hardened, 5/8 inch ID

108 102 MODEL 6 POWER WHEEL SINGLE SPEED UNITS When servicing individual components, a decal on the power wheel as shown indicates the original wheel has been replaced with Auburn Gear # If so, order the part numbers prefaced with the symbol in the parts listing next page. See Note 1, next page.