SELF-PROPELLED WINDROWER

Transcription

1 SELF-PROPELLED WINDROWER MaeDan 9000 Series (Serial No and up) Westward 9000 Series (Serial No and up) Prairie Star 4900 Series (All Serial Nos.) Premier 2900 Series (All Serial Nos.)

2

3 MaeDon 9000 Series I Westward 9000 I Prairie Star 4900 I Premier 2900 Self-Propelled Windrower Parts Catalog SERIAL BREAKS The side of the serial number on which the dash (-) appears determines whether the part is used "up to" or "after" the serial number given. Example: Used on machines up to and including serial number Used on machines including and after serial number When ordering, be sure the complete and proper serial number is given. ABBREVIATIONS LlH - left hand RlH - right hand LefURight Hand is determined from Operator's position, facing forward inside diameter outside diameter NR - as required (quantity varies) - reference, part number called up elsewhere in catalog NC - national coarse thread NF - national fine thread HARDWARE Common hardware is not illustrated. Alphabetic references are used to designate position and description of these items.

4 ii ALPHABETICAL INDEX!'!. Air Cleaner & Pre-Cleaner, Engine.44 Air Conditioning, Cab 25 Air Conditioning, Engine Group 27 Air Intake Screen, (Ser.# ) 49 Air Intake Screen, wi Cleaner (Ser.#-82885) 47 Air Intake Screen, Std. (Ser.# 82885) 46 Alternator 40 A!! Belt, Fan/Alternator. 39 Belt, Header Drive Blower, Cab Brake Assembly 77!< Cab Seals, Grommets & Mounts Casters, 16.5 Forked.. 79 Casters, 9.5 Forked 81 Casters, Formed 83 Center Link, Tractor to Header 33 Compressor,. AlC 27 Condenser, AlC 27 Control Knobs & Switches 14 Conveyor Speed Control, Cab 15 Cooler, Hydraulic Oil 63 Cylinder, Header Clutch 51 Cylinder, Header Lift.., 63 Cylinder, Header Lift Seal Kits 63A,63B Q Decals, Information 87 Decals, Product Identification 89 Decals. Safety 85 Door,' Cab 5 Driveline: Engine to Bevel Gearbox 53 Driveline: Tractor to Header 55.E Fan, Engine.. 39 Filter, Fuel Line Filter, Hydraulic Oil ,63 Filters, Engine Oil & Fuel Footrest, Cab Frame, Cab Frame, Tractor.. 31 Fuel System !< Gauges Gearbox, Bevel Ground Speed Lever 17 Ground Speed Linkage (Ser.# ) 59 Ground Speed Linkage (Ser.# ) 91!! Header Drive.. 51 Header Drive Pulley Heater Hydraulics: Cylinder Control 63 Hydraulics: Double Gear Pump 65 C Hydraulics: Header Drive 61 Hydraulics: Traction Drive 65 Hydraulics: Triple Pump.. 65 A Hydraulics: Wheel Motor 65 E! Ignition Switch. 13 Instrument Panel , Ladder 31 Lift Linkage 33 ~ Electrical, Cab 21 Electrical, Ground Speed Lever Electrical, Roof Electrical, Tractor Engine Air Intake Engine Assembly 39 Engine Cooling.45 Engine Superstructure.41 Evaporator, AlC 25 Muffler. Neutral Interlock. Numerical List.... Oil Pressure Switch.. o

5 ALPHABETICAL INDEX iii E Paint 87 Panel, Cab Right Side Panel, Cab Side Console Panels & Supports, Engine/Rad 41 Pintle Arms, Traction Drive Power Wheel B Radiator Radiator Supports......,. 41 Reel Speed Control, Cab 15 Reflectors Roof, Cab (& Roof Electrical) W Walking Beam & Pivot. Weight Package, Rear. Wheel Motor Ass'y.: Single Speed Drive Wheel Motor Ass'y.: Two Speed Drive. Wheel Motor Components. Wheels & Tires, Drive. Windows. Windshield Wiper E Seat Sheet Metal Covers, Tractor Side Console, Cab Starter 39 Steering Column 11 Steering Linkage (Ser.# ) 59 Steering Linkage (Ser.# ) Stocking List, Suggested 98 Switch, Ale Pressure Switch, Engine Oil & Temperature 39 Switch, Header and Reel Lift 17 Switch, Header Drive Neutral Switch, Hydraulic Oil Pressure 63 Switch, Neutral 57 Switches, Side Console 14 I Tank, Hydraulic Oil.. 65 Temperature Sender & Switch 39 Throttle Control Tires, Caster 79,81,83 Tires, Drive Two-Speed Drive: Lever/Cable Assembly 66 Two-Speed Drive: Linkage Assembly 67 Two-Speed Drive: Wheel Motor Assembly 69 Upholstery A

6 iv

7 1 TABLE OF CONTENTS CAB Cab Frame. Seals, Gronvnets & Mounts 2,3 Upholstery A., 38 Cab COOf & cab Right Side Panel 4,5 Cab Roof (& Roof EIedricaI) 6,7 Ih'indows 8 Footrest & Side Console Panel 9 Steering Column 10,11 Instrument Panel 12,13 Side Console 14 Reel & Conveyor Speed Control 15 Ground Speed Lever ThrotueControl Cab Electrical & Wiper Seat 22,23 Cab Air Conditioning & Blower Group. 24,25 Air Conditioning. Engine Group ,27 Heater ,29 TRACTOR Main Frame & Covers 30,31 lift linkage 32,33 Walking Beam & Pivot 34 Rear weight Package 35 Tractor Electrical 36,37 Engine Assembly AltematOf" Mounting.40 A Engine Superstructure 41 Fuel System 42,43 Engine Air Intake 44 Engine Cooing 45 Standard Air Intake Screen (5er and below) 46 Air Intake Screen with Cleaner (Ser and below) 47 Air Intake Screen (Ser #82886 and above) 48,49 Header Drive 50,51 Bevel Gearbox 52 Driveline (Engine to Bevel Gearbox) 53 Header Drive Pulley 54 Driveline: Tractor to Header 55 Neutral Interlock & Pintle AnTIS 56,57 Steering & Ground Speed (5er #82886 and above) 58,59 Hydraulics: Header Drive 60,61 Hydraulics: Cylinder ControL... 62,63 Hydraulics: Header Lift. Cylinder Seal Kits 63 A. 63 B Hydraulics: Traction Drive 64,65 Hydraulics: Triple Pump 65 A Hydraulics: Double Gear Pump 65 C Hydraulics: Wheel Molor 65 E Two-Speed Drive: Lever/Cable Assembly 66 Two-Speecl Drive: Unkage Assembly 67 Two-Speecl Drive: Wheel Motor Assembly 68,69 Single Speed Drive: Wheel Motor Assembly 70,71 Power Wheel n,n Drive \I'oJhet1s & TIreS 74,75 Brake Assembly 76,n 16.5 Forited casters Forked Casters 80,81 Formed Casters 82,83 Safety Decals,, 64,65 lnfonnalion Decals, Reflectors & Paint Produd Identification Decals Steering & Ground Speed (Ser #82885 and below) 90,91 NUMERICAL LIST SUGGESTED STOCKING LIST 98.99

8 2 CAB FRAME, SEALS, GROMMETS & MOUNTS 12 " o ~~~o 3 0 '" top view side view 7 8 A~Ql ==. c-\t:li'l B ---""" I! I,, cab mounts

9 3 PART CAB FRAME, SEALS, GROMMETS & MOUNTS DESCRIPTION QTY SERIAL CAB FRAME - with decals CAB FRAME - with decals SEAL - foam, top front SEAL - foam, lop side SEAL - foam, top rear SEAL - foam, window SEAL - foam SEAL - foam, blower ports SEAL - foam... 2 SEAL - moulded, window MOULDING - protective 2 MOULDING - protective, right side CONDUIT - slit GROMMET INSULATOR - cab mount WASHER - flat A B c SOLT hex head, 112 NC x 3 inch (except front right) BOLT - hex head, 1/2 NC x inch (front right only) NUT - hex, 1/2 NC - double nutted (except front right) NUT - serrated flange, 1/2 NC - single nut (front right only) WASHER - lock, 1/2 inch (except front right)

10 3A CAB UPHOLSTERY & INSULATORS '~

11 3B PART CAB UPHOLSTERY & INSULATORS DESCRIPTION QTY SERIAL FLOOR MAT INSULATOR - upper front, UH & R/H 2 INSULATOR - upper side, UH & RlH INSULATOR - upper left, rear INSULATOR - upper right, rear 1 UPHOLSTERY - above front window UPHOLSTERY ~ above UH side window... 1 UPHOLSTERY - above R/H side window UPHOLSTERY above rear window UPHOLSTERY left post UPHOLSTERY - left post 1 UPHOLSTERY - right post, UPHOLSTERY ~ below rear window UPHOLSTERY - door UPHOLSTERY - door UPHOLSTERY - cab roof, see page

12 4 CAB DOOR & CAB RIGHT SIDE PANEL 8 \ A H~ /' G, 9 6 I I u~a J I, DE 1 F

13 5 CAB DOOR & CAB RIGHT SIDE PANEL PART DESCRIPTION QTY SERIAL A B C E F G H J K L M N P R ~f DOOR DOOR - frame, less lower panel. 1 SEAL - door, moulded _ 1 HANDLE - outer, with keys HANDLE - outer, with keys KEY -door 1 KEY - door LATCH - doof CATCH - door latch STOP - door ". ".., PANEL - right cab side SHIM - door catch,... 1 PANEL - lower door HANDLE - inside KNOB - plastic , , _... 1 BAR - outer handle link..., LATCH - door SPRING - door latch, ,. 1 PIN - door latch BOLT - flange head, 3/8 NC x 1/2 inch BOLT - flange head, 1/4 NC x 1/2 inch SCREW - flat socket head. #10 NC x 3/4 inch NUT - lock, smooth flange, 3/8 NC distorted thread BOLT - hex head, 3/8 NC x 1 1/2 inch NUT - lock, 1/2 NC distorted thread WASHER - lock. 3/8 internal tooth NUT - serrated flange, 3/8 NC SCREW - self-drilling, self-tapping, #12 x 1 inch NUT - hex, 3/8 NC NUT - hex, 1/4 NC BOLT - hex head, 1/4 NC x 1/2 inch BOLT - flange head, 3/8 NC x 1/2 inch WASHER - lock. 1/4 BOLT - hex head, 1/4 NC x 1 1/2 inch Indicates where hardware passes through cab or door frame

14 6 CAB ROOF A 8 4 _ '3.~ 1l I 5 11 :C--, RAIlIO RELATED PARTS

15 7 PART CAB ROOF DESCRIPTION QTY SERIAL A B D E F G H J ROOF - cab, includes roof, headliner and items 2-6 inclusive 1 UPHOLSTERY - roof 1 INSULATOR - fronl (shown) 3 INSULATOR - rear (similar) 3 NUT - tee, #10 NC (for wiper motor and amber light mounting) 12 NUT spong, #Ij NC (for field & head lamps) 32 SPACER - roof/headliner 6 WASHER - ftal 12 PAD 6 GROMMET - See Cab Frame 6 LIGHT - amber, replacement bulb # LAMP - wide flood, sealed beam #H LAMP ~ trapezoid (headlight), sealed beam #H GASKET - lamp 8 BEZEL - lamp 8 LIGHT - interior 1 LIGHT - interior 1 LIGHT - tum indicator. 2 NUT - spring 2 MIRROR. 1 SUPPORT - mirror 1 CONDUIT - sl" hose (was 25298) 1 HARNESS - electrical, roof 1 INSULATOR - harness 4 FASTENER - plastic tie 3 MOULDING - protective 2 PLUG - plastic, radio/speaker locating holes 3 SUPPORT - rear, radio 1 SPEAKER - radio 2 GRILLE - speaker 2 ANTENNA - radio 1 DECAL - covering, radio cut-out 1 SEAL - foam 2 BOLT - hex head, 1/2 NC x 7 inch NUT -lock, 1/2 NC distorted thread SCREW - machine, #10 NC x 2 inch SCREW - machine, #6 NC x 1 inch SCREW - self tapping, #8 x 314 inch BOLT - ftange head, 1/4 NC x 3/4 inch NUT - serrated flange, 1/4 NC SCREW - self tapping, #8 x 1 inch

16 8 WINDOWS 10 \ 12-4, "Ci9 \, ~~. ~ 7...'3 16 / \ 18~\ 4 PART "-l.--~ DESCRIPTION QTY SERIAL A B SEAL - top, front windows, '" " 1 SEAL - bottom, front windows 1 WINDOW - front 1 WINDOW - side 2 SEALANT - black, use neutral cure silicone (Silicone II or Silglaze) AR WINDOW - rear 1 SEAL - rear window 1 WINDOW - right, assembly (includes item 10) 1 SUPPORT - window 1 LATCH - rear 1 LATCH - front 1 FASTENER GROUP -latch (indudes screw, bushing and nut) 2 SEAL - door window 1 WiNDOW-door 1 RIVET - latch 2 KIT - window retaining, lower - indudes S shaped retainer plus item RETAINER -window retaining, lower ANGLE - window retaining, upper 1 INSULATOR - window, lower front. 1 BOLT - flange head, 1/4 NC x 1/2 inch SCREW - self drilling, self tapping #12 x 1 inch

17 WINDOW SPECIFICATIONS SA j f- 65 f FRONT (42093l front LEn front RIGHT (42094) 5.97 'r 19 II: (4) ~ C---'- 1' ,1 -'-----f ~ r-673 -, r i R[A.q (42095) /;) R '<il) ~"I~ 713 J 13 R (4) :,) ' OOIJR L J (42096) NOT::::;, I. MATERIAL' Ught ond hen1: reflective, tenpp,.f>d or 10'...;1'\O't"<I olo:te, : or sheet g1055, 70% light von5mittc.nci;', A.f,G. or worq'ion Green. Sholl Meet surety specification per StI( J Mo.nvl'o.cture to SA( J673b. 3. All d;l"ien5,on5 in niuine1:ers. 7<5r " r-665 i RIGHT SIDE 1 (42097> 560 ro{j;-s I 920 f j.-,j ~ I -'---- r 13 R (2) 5.97

18 88

19 9 FOOTREST & SIDE CONSOLE PANEL 5---,i. ~'~\ t-4, R, A B I A PART DESCRIPTION QTY SERIAL A B R ROD - footrest 2 PANEL - side console, includes items 3, 4, 5 and 6 1 S~L-~p 1 SEAL - vertical SEAL - front vertical SEAL - Ale compartment NUT - serrated flange, 3/8 NC NUT - lock:, smooth flange, 318 NC distorted thread Hardware passes through seat support panel.

20 10 STEERING COLUMN 11,~ """" \12 6 " l:?. /~(J" 18 / 19 /14 o ~J / ~, 13 / C 8

21 11 STEERING COLUMN PART DESCRIPTION QlY SERIAL C SHAFT - steering, with sprocket BUSHING - shaft WASHER - flat, 13/16 inch I.D _ 5 U-JOINT SHAFT - steering, upper PIN - spring, 1/4 x 1 inch TUBE - steering HANDLE - wheel adjustment BUSHING - lower 1 BUSHING - upper WHEEL - steering PIN - spring, 1/4 x 1 1/2 inch PIN - spring, 1/4 x 1 1/4 inch 1 WASHER - thrust.. 1 KNOB - ball 1 GUIDE rubber... _ INSULATOR - steering post, foam 1 INSULATOR - steering post, foam BOLT - socket head, 318 NC x 1/2 inch WASHER - flared WHEEl- steering, with cap (item 21) CAP steering wheel 1 INSTALLATION KIT - includes hub, snap plale & bolls BOLT - round head, square neck, 1/2 NC x 1 inch NOTE: For Related Parts, see "Steering & Ground Speed", page 58.

22 12 INSTRUMENT PANEL 3 4, : 2 ' ,' r_ --, '~' d:, _." ', CD!if'.'. I,\""v I,-I '---':1,- -I I~±' 1==1 1-' L-:- --l, ""'A '@ ""~.. ~. /' B 9 I ---"I 1 (~.- 'I I < y.;::_1 '. 7 6 I.(j>."'::'" '"..,.:;:. 0\o=- _._- ~ :p~ f\"

23 13 PART INSTRUMENT PANEL DESCRIPTION QTY SERIAL A PANEL - instrument, with decals GAUGE - hour meter GAUGE - fuel GAUGE - voltmeter,. 1 GAUGE ~ temperature, engine coolant LIGHT - indicator NUT - spring, for indicator light SWITCH - ignition, with keys 1 KEY - ignition. for switch INSULATOR - foam GAUGE - tachometer (optional) SENDER - tachometer NUT - jam, 314 NC, for tach sender VENTILATOR LIGHTER - cigarette SCREW - self tapping

24 14 SIDE CONSOLE o PART DESCRIPTION QTY SERIAL PANEL - console, with decal- includes items 2 & 15 and hardware 1 PANEL - console, with decal- includes items 2 & 15 and hardware 1 SEAL - right post 1 FLASHER CONTROL - with knob 1 SWITCH -light, with knob 1 SWITCH - wiper 1 KNOB - control.4 SWITCH - blower 1 THERMOSTAT ASSEMBLY 1 LIGHTER - cigarette 1 ASHTRAY 1 S\fIJ1TCH - toggle, header drive 1 S\fIJ1TCH - header drive 1 S\fIJ1TCH - toggle, header drive 1 GUARD - for toggle switch REEL & CONVEYOR CONTROL ASSEMBLY. see page 15 2 GAUGE - hour meter 1 SWITCH - deck shift, 960 & 972 Hydraulic Deck Shift Hdrs. (was 42257) 1 PANEL - access A B C SCREW - button head, rib neck #12 NC x 5/8 inch NUT -lock, #12 NC distorted thread SCREW - self tapping

25 15 REEL & CONVEYOR SPEED CONTROL PART DESCRIPTION QTY SERIAL A B KNOB - control. 2 WASHER - non metal PIN - roll, 1/4 x 1 3/4 inch... 2 STOP - knob travel. 2 SPACER HOSE CONTROL BLOCK - header drive, see "Header Drive Hydraulics" 1 BOLT - hex head, 1/4 NC x 1 inch BOLT - hex head, 1/4 NC x 5/8 inch

26 16 GROUND SPEED LEVER \ \ J 8 f~~ I,, 5 ~/ 18 A, A l &_,~2 r~-15 J'J '~I /;/ / ~-J' K14 17! "-.<\' / 16 ~ 13 Serial Number and below Serial Number and above

27 17 GROUND SPEED LEVER PART DESCRIPTION QTY SERIAL A B G D E F G H J K L M Nf LEVER - ground speed BUSHING - plastic (part consists of two halves) FLANGE bushing mounting PAD - friction BAR adjusting WASHER - non metal 1 ANGLE - mounting PAD - wear HANDLE - ground speed. 1 HARNESS - ground speed lever, inel. two switches (item 9) & decals.. 1 HARNESS - ground speed lever, inel. two switches (item 9) & decals.. 1 SWITCH rocker 2 TAPE - foam (between switches) 1 BOLT hook 1 CABLE - neutral interlock, see "Neutral Interlock & Pintle Arms"... 1 ROD - steering, see "Steering & Ground Speed" INSULATOR rubber 1 WASHER flat LEVER - ground speed PAD - friction BUSHING - plastic SPRING - compression WASHER - flat NUT - lock, smooth flange, 5/16 NC distorted thread NUT jam. 3/8 NG BOLT - round head, square neck, 3/8 NC x 3/4 inch NUT - lock, smooth flange, 3/8 NC distorted thread BOLT - hex head, 3/8 NC x 3/4 inch WASHER - lock, 3/8 inch WASHER - flat, 13/32 inch 1.0. SCREW - set, 5/16 NC x 1/4 inch NUT - hex, 3/8 NG BOLT - round head, square neck, 1/2 NC x 5 inch NUT - lock, 112 NC distorted thread NUT hex, 1/2 NG Indicates where hardware passes through frame member

28 18 THROTILE CONTROL " 7 -, - (p,,-,-,e,," 15./'/ ~,~ ":.. () ()....,., ;;o"-\~~l--<.. p ;'>~""' '~:;.~:.:.. D' B' ': ENGINE END 14 ~ H i l\r'.'" \ \ E I 3 CAB END A & I ~E

29 19 PART THROTILE CONTROL DESCRIPTION QTY SERIAL SUPPORT throttle, in-cab 1 LEVER - throttle 1 PAD - friction 2 SPRING - compression 1 WASHER - flat 1 KNOB - orange 1 CABLE - throttle 1 PIVOT - cable 1 HOLDER - cable 2 BAR - spacer 2 SPRING extension, to fuel pump lever 1 SUPPORT - cable to spring 1 SUPPORT - throttle cable, engine end : 1 INSULATOR - rubber, throttle cable (see note 3) 1 SPRING - extension 1 CLEVIS - throttle cable 1 LEVER - throttle 1 GROMMET - rubber. 1 CLIP - cable holder 1 see note 1 see note 1 see note 1 see note 2 see note 2 see note 2 see note NOTES 1. For Turbo Engine, these items are used for Serial No and below, except Tractor Serial No For Naturally Aspirated Engine, these items are used for. Serial No and below Serial No. blocks to and to Serial No and above 2. For Turbo Engine, these items are used for Serial No and above, plus Tractor serial No For Naturally Aspirated Engine. these items are used for Serial No to , except Serial No. blocks to and to Mounting position for Item 14 INSULATOR at slots in Ilem 13 SUPPORT varies as follows: For Turbo Engine with Serial No and below, use two rearward slots. For Naturally-Aspirated Engine with Serial No and below, use two forward slots. For Naturally-Aspirated Engine with Serial No and above, plus Serial No. blocks to and to , use two rearward slots. A B C o E F G H J K L M N p R S T U V W - f BOLT hex head, 3/8 NC x 1"4 inch BOLT round nead, square neck, 318 NC x 1 inch SCREW machine, #10 Ne x 1/2 inch NUT hex, '10 NC NUT -lock, smooth flange, 318 NC distorted thread SOLT hex head, 318 NC x 3/4 inch PIN - cotler, 3132 x 314 inch NUT hex, '10 NF SCREW machine, '10 NC x 314 inch BOLT - flange head, 318 NC)l 314 inch SOLT hex head, M6 )l 15 mm WASHER lock, M6 BOLT hex head, 318 NC x 1 1/2 inch NUT - hex. 318 NC BOLT round head, square neck, 5116 NC x 1 1/2 inch NUT -lock, smooth nange, 5116 NC distorted thread SCREW set, 318 NC x 1 inch NUT - jam. 318 NC NUT - hex, Yo NC BOlT-14NCx 1 inch Indicates where hardware passes through frame member.

30 20 5 ' CAB ELECTRICAL & WIPER ~ ~ - ~1~~~ijfJ TOP VIEW i, I',1, I I' Ii 'L I il I i~ ~ I '~,:;---' i,_!l.l I 8 16 \, () SIDE VIEW I, -) \ r' \ \ 12 ~~ c _.- _1_...1 H D JK ",I

31 21 PART CAB ELECTRICAL & WIPER DESCRIPTION QTY SERIAL A B C D E F G H J K HARNESS - cab wiring, with plug & rectifier (item 19) HARNESS - cab wiring, with plug & rectifier (item 19) SUPPORT - circuit breakers, BREAKER - 6 amp (Serial No and below, qty. = 3) 2 BREAKER 25 amp MOTOR wiper 1 WIRE - wiper motor ARM - wiper BLADE - wiper PLATE - wiper "..,,.,,.,.., 1 INSULATOR - foam 1 PANEL - access... 1 RELAY w electrical (Serial No and below, qty. = 3), 4 BUZZER 1 CLIP - harness FASTENER - plastic tie, push mount ,., 3 FASTENER - plastic tie..., 7 CABLE ~ ground SWITCH - park brake RECTIFIER - diode pack WASHER -lock, #10 NUT - hex, #10 NF NUT - serrated flange, 1/4 NC WASHER - lock, 3/8 inch, internal tooth WASHER -lock, #10, internal tooth NUT - hex, #10 NC SCREW - machine, #10 NC x 1/2 inch SCREW - hex washer head, #10 x 5/8 inch BOLT - flange head, 3/8 NC x 1 inch NUT - lock, smooth flange, 3/8 NC distorted thread

32 22 SEAT "/ 1 7 (, I I Q 0 ~4 / 25 Q 6 I ,/ '" "----! \?', /,~...,J \! A! j 0 26

33 23 PART SEAT DESCRIPTION QTY SERIAL SEAT - spring suspension, complete SEAT - spring suspension, complete 1 ADJUSTER ASSEMBLY - weight, spring suspension seat 1 ADJUSTER ASSEMBLY - weight, spring suspension seat 1 SPRING 2 SPRING - extension, set of two 1 SHOCK ABSORBER ASSEMBLY - spring suspension seat..... '. 1 SHOCK ABSORBER - spring suspension seat 1 SUSPENSION OVERHAUL KIT - spring suspension seat SLIDE RAILS KIT - spring suspension seat 1 SLIDE RAILS KIT - set of two, spring suspension seat 1 BACKREST & CUSHION - spring suspension seat SEAT CUSHION - spring suspension seat ARMREST KIT - set of two, spring suspension seat SEAT - air suspension, complete SEAT CUSHION - air suspension seat BACKREST & CUSHION air suspension seat ARMREST - left, air suspension seat 1 ARMREST - right, air suspension seat 1 SLIDE SERVICE KIT - air susp. seat, includes both sides & latch wire. 1 AIR CONTROL VALVE SERVICE KIT - includes valve, knob & hardware1 KNOB - air valve 1 COMPRESSORflNlRE HARNESS SERVICE KIT - ind compressor. hamess & nardware. 1 KNOB SERVICE KIT - includes back tilt, seat tilt, lumbar & slide knobs 1 VERTICAL SUSPENSION SHOCK SERVICE KIT - air suspension seat 1 FORE AFT ISOLATOR SHOCK SERVICE KIT - air suspension seal.. 1 BEARING SERVICE KIT - air suspension seat, includes all bearings.. 1 AIR LINE & FITTING SERVICE KIT air suspension seat 1 AIR SPRING - air suspension seat PANEL - seat, with seals SEAL foam... 2 PLUG - plastic, spring suspension seat PLUG plastic. for 5/16" hole PLUG - plastic, for 31S" hole A D E F K L NUT - lock, smooth flange. 318 NC distorted thread BOLT hex head, 5/16 NC x 314 inch WASHER - lock, 5/16 inch NUT hex, 5/16 NC BOLT hex head, MS x 20 mm WASHER - lock. M8

34 24 CAB AIR CONDITIONING & BLOWER GROUP ~14 15 A ~1, 20-6.' ~'I i... '7 13 / D ~f E

35 25 PART CAB AIR CONDITIONING & BLOWER GROUP DESCRIPTION QTY SERIAL A B C D E _I VALVE - expansion (R-12 system) VALVE - expansion (R134a system) 1 O-RING - evaporator to expansion valve (R-12 system) 2 O-RING - evaporator to expansion valve (R134a system) 2 HOSE - air conditioning, liquid - with O-rings (R-12 system) 1 HOSE - air conditioning, liquid (R134a system) HOSE - air conditioning, suction - with O-rings (R-12 system) HOSE - air conditioning, suction (R134a system) INSULATOR foam RETAINER - evaporator EVAPORATOR I HEATER CORE - (R-12 system). 1 EVAPORATOR I HEATER CORE - (R134a system) 1 BAFFLE - foam. 1 PAN - condensate, (includes foam pad bonded to underside of pan) 1 HOSE - drain CLIP - drain hose PAD - rubber BLOWER - complete VENTILATOR - circular VENTILATOR - rectangular FILTER - return air, (located on cab rear wall).. 2 GRILL - return air filter 2 KNOB plastic... 4 CLEANER air intake, (located under rear overhang of cab roof) 1 RETAINER - cleaner KNOB - plastic THERMOSTAT - with capillary tube & conduit SWITCH blower control KNOB - control SWITCH - low pressure (R134a system) O-RING - for hose (R-12 system) 2 O-RING - for hose (R134a system).. 2 O-RING - for hose (R-12 system). 2 a-ring for hose (R134a system). 2 NUT - lock, smooth flange, 3/8 NC distorted thread BOLT - flange head, 3/8 NC x 3/4 inch BOLT - round head, square neck, 3/8 NC x 3/4 inch NUT - serrated flange, 1/4 NC BOLT - hex head, 114 NC x 51S inch Indicates where hardware passes through frame member NOTE: For related parts, see "Air Conditioning - Engine Group", page 26.

36 26 AIR CONDITIONING - ENGINE GROUP

37 27 AIR CONDITIONING - ENGINE GROUP PART DESCRIPTION QTY SERIAL CONDENSER 1 CONDENSER (includes item 21) 1 O-RING - condenser to drier connection (R-12 system) 1 O-RING - condenser to drier & switch to drier (R134a system)... 3 DRIER/RECEIVER (R-12 system). 1 DRIER/RECEIVER (R-12 system).. 1 DRIER/RECEIVER (R134a system). 1 DRIER/RECEIVER (R134a system). 1 DRIER/RECEIVER (R134a system). 1 SWITCH high/low pressure (R-12 system, not exactly as shown) 1 SWITCH - high pressure - with O-ring (R134a system) 1 BAND - drier mount SUPPORT - drier. 1 HOSE - air conditioning, liquid ~ with O-rings (R-12 system). 1 HOSE - air conditioning, liquid (R134a system) l HOSE - air conditioning, discharge - with O-rings (R-12 system) l HOSE - air conditioning, discharge (R134a system)..1 GROMMET - hose protector, COMPRESSOR - (R-12 system).. 1 COMPRESSOR - (R134a system), see NOTE COMPRESSOR - (R134a system), see NOTE BELT - compressor drive. 1 BAR - bell tightener BAR - belt tightener Order according to Serial Number breaks shown except Tractor Serial No This unit is equipped with the same components as those units with Serial No and up. HOSE - air conditioning, suction - with O-rings (R-12 system) HOSE - air conditioning, suction (R134a system) STRIP - hose protector. 2 HOLDER - hose. 2 O~RING - for hose (R-12 system). 2 O-RING - for hose (R134a system). 2 O-RING - for hose (R-12 system). 2 O-RING - for hose (R134a system). 2 O-RING - for hose (R-12 system). 2 O-RING - for hose (R134a system). 2 HOSE - air conditioning, liquid (R134a system) HOLDER - hose..1 FiniNG - adapter (brazed on to condenser) 1 HOSE - slit, hose protector DqO DOO " D A B D E F G NUT -lock., sm. fl., 3/8 NC dis\. thread BOLT md hd, sq nk. 3/8 NC x 3/4 inch NUT hex, 3/8 NC BOLT - hex head. 112 NC x 1 \14 inch BOLT - md hd. sq nk, 3/8 NC x 1 1/4 inch BOLT - md hd, sq nk, 3/8 NC x 1 inch H J K BOLT - hex head, 3/8 NC x 11/4 inch BOLT - md hd, sq nk. #10 NC x 112 inch NUT - hex, #10 NC - f Indicates where hardware passes through frame or support member. NOTES: 1. For related parts, see "Cab Air Conditioning & Blower Group", page Compressor includes total system requirement of refrigerant oil: 210 cc (7.1 US fl.oz.) SP-20 PAG. 3. Compressor includes total system requirement of refrigerant oil: 240 cc (8.1 US fl.oz.) SP-20 PAG.

38 28 HEATER ~-6 ~-12 7""" c, M f ~ II B '~~ ~ 2 '" l 14-~ 6-~,, "'" "

39 29 HEATER PART DESCRIPTION QTY SERIAL A B C D E ~f VALVE - heater SUPPORT heater valve TUBE - heater control WASHER flat KNOB - control CLAMP - hose HOSE - heater, valve to bottom of heater core 1 HEATER CORE I EVAPORATOR (R 12 Ale system) 1 HEATER CORE I EVAPORATOR (R134a AlC system) 1 HOSE - heater, engine water pump housing to top of heater core 1 ELBOW barbed, 1/2 NPT x 5/8 I.D. hose (see note 1) 1 HOSE - heater, valve to top of engine block (fan end) 1 FITTING - barbed, 1/2 NPT x 5/8 J.D. hose.. 1 CLIP - insulated VALVE ~ shut off.. 1 SCREW - self tapping, #10 x 3/8 inch NUT - serrated flange, #10 NC SCREW - machine, #10 NC x 1/2 inch BOLT - round head, square neck, 3/8 NC x 3/4 inch NUT - lock, smooth flange, 3/8 NC distorted thread Indicates where hardware passes through frame or support member NOTES; 1. For item 10: May sub item 14, shut off valve for maximum AlC function.

40 30 15 MAIN FRAME & COVERS 14 G "" ~.~. H \ \ \ \ \ \ ~ E/ 9 J , "I I c B \ / / 2 11 \ A /! I \ D

41 31 MAIN FRAME & COVERS PART DESCRIPTION QTY SERIAL A B C E G H J K L M Nf _s FRAME - main, not serviced COVER - left inner leg COVER - right inner leg SHIELD - left side. 1 SHIELD - right side SEAL - side shield, rear PAD - rubber, (see NOTE 1, below) 2 BRACKET - bumper mount BAR - shield to pivot BAR - pivot to frame SPRING - shield. 2 PANEL - left, with tool shelves BRACKET - panel mount LADDER - step COVER - engine, see "Engine Superstructure" HANDLE - shield ROD - shield... 2 BOLT - flange head, 3/8 NC x 3/4 inch NUT - lock, smooth flange, 3/8 NC distorted thread BOLT - flange head, 1/2 NC x 1 inch BOLT - round head, square neck, 3/8 NC x 3/4 inch BOLT - hex head, 3/8 NC x 1 1/4 inch WASHER - flat, 13/32 inch 10 PIN - cotter, 1/8 x 1 inch PIN - cotter, 1/4 x 2 inch NUT - hex, 3/8 NC BOLT - hex head, 3/8 NC x 1 lf2 inch BOLT - hex head, 3/8 NC x 1 inch Indicates where hardware passes through frame member. Indicates where hardware passes through side shield NOTES: 1. If rubber pad is supplied in place of rubber bumper, remove bumper mount bracket (item 6) and install pad as shown.

42 32 s, 42 ~ '\ ~ ~~ \,=, a "" 39 T~ J 32

43 33 PART LIFT LINKAGE DESCRIPTION QTY SERIAL B A B C D E G H J L M N P R S T U V SPRING - extension 4 INSERT - spring 8 CHANNEL - front mount ARM - front mount PIN - straight, front spring 2 BAR - gauge... 1 BAR - header height gauge, with decal CLEVIS - rear mount. 2 PIN - straight, rear spring.. 2 DRAW BOLT - spring, hex head. 2 WASHER - flat, hardened.. 2 PIN - "L" PIN - hair SUPPORT - linkage, with decals. 2 BLOCK - wear (shown positioned for 920, 930 or 940 headers).. 2 BAR - wear block. 2 PAD - rubber, lower leg PLATE - pad cover WASHER - fiat. 2 ARM - top link, with lube fitting (item 28).2 FITTING -lube 2 PIN - top link {rear) ~ 2 PIN - cylinder (rear) and top link (front) PLATE - header levelling (was 44989, qty. 2).4 PAD rubber, top link CYLINDER - header lift, see "Hydraulics: Cylinder Control, page 63 PIN - cylinder (front). 2 BAR - cylinder mount.. 2 STOP - cylinder HOOK - cylinder stop.. 2 PIN - clevis, center link JOINT ASSEMBLY - center link, includes items 33 to 37 1 JOINT - ball, RlH thread (header end) 1 COLLAR -locking 1 PIN - roll 2 TUBE - center link 1 JOINT - ball, UH thread (tractor end) 1 BAR - header height gauge, with indicator decal 1 AUXILIARY FLOAT SPRING KIT - for heavier headers: 36' ' 920 (Kit available through WholeGoods only) INSERT - spring, outer 1 INSERT - spring, intermediate 1 INSERT - spring, inner SPRING - extension, inner 1 NUT hex. 5/8 NC BOLT - hex head, 318 NC x inch BOLT - hex head, 3/8 NC x 2 inch NUT - lock, smooth flange, 3/8 NC distorted thread WASHE:R flat, inch 10 BOLT - hex head, 318 NC x 3/4 inch NUT -lock, 1/2 NC nylon insert BOLT round head, square neck, 1/2 NC x 3 inch BOLT - round head, square neck, 3f8 NC x 314 inch BOLT - round head, square neck, 3/8 NC x 1 3/4 WASHER lock, 3/8 inch NUT - hex, 318 NC BOLT - hex head. 318 NC x 1 inch PIN - coller, 3/16 x 1 1/4 inch BOLT round head, square neck, 112 NC x 3 inch: Auger & Multi-Crop Headers BOLT round head, square neck, 1/2 NC x 5 inch: Draper Headers NUT lock, 318 NC distorted thread BOLT - round head, square neck, 318 NC x 1 inch

44 34 WALKING BEAM & PIVOT o C EAI PART DESCRIPTION QTY SERIAL A C E BEAM - walking, with bushings & decals 1 BUSHING - bronze 2 FITTING - lube PIVOT - walking beam 1 BOLT - hex head, 3/4 NC x inch WASHER - lock, 3/4 inch NUT - hex, 3/4 NC WASHER - flat, 13/16 inch 1.0.

45 35 REAR WEIGHT PACKAGE rr==!!',-- --=--"" / / / \ \ \ ~~= INSTALlATION OF WEIGHTS (REAR VIEW) 1- J ra\ O~ "il ~ I- l,~,r +- direction of travel PART DESCRIPTION QTY SERIAL 1 A B B NOTE: KIT - rear weight, includes 187 lb. (65 kg) weight pack and hardware.. * (Kit available through WholeGoods only.) BOLT - hex head, 3/4 NC x 3 inch NUT - hex jam, 3/4 NC 1 or 2 kits may be installed, as required.

46 36 TRACTOR ELECTRICAL 21 ~3 4 5 ~1.~,. 20. W SR,,~\~~! ~ z, 1,.J I:»',M r!..u y 'p I. T I N,.\. I V, I'X U"~14 'L, " 11 F K 103m

47 37 PART TRACTOR ELECTRICAL DESCRIPTION QTY SERIAL 1 1A HARNESS - wiring, tractor section 1 HARNESS - Wiring, tractor section 1 HARNESS wiring, tractor section 1 - Order according to Serial Number breaks shown except Tractor Serial No This unit is equipped with the same components as those units with Serial No and up. CONNECTOR KIT - 3 way (includes male and female plugs) FASTENER - cable tie 10 FASTENER - cable tie, push mount.. 5 GROMMET GROMMET CLIP - harness. 10 HOLDER - battery.. 1 CABLE - starter to battery. 1 INSULATOR - starter 1 COVER - battery cable 1 CABLE - ground, battery to frame 1 CABLE.- ground, engine mount to frame 1 LIGHT - red, replacement bulb # LAMP - medium flood, sealed beam #H GASKET -lamp mounting 1 BEZEL -lamp 1 BREAKER circuit, 50 amp 2 RELAY - electrical 1 COVER - relay 1 HARNESS - wiring, adapter - naturally aspirated engine 1 - Plus Senal No. blocks to and to t 17409' " "" A B C D E F G H I J K L M N P R S T U V W X y Z BOLT - round head, square neck, 3/8 NC x 3/4 inch NUT -lock, smooth flange, 3/8 NC distorted thread BOLT - hex head, M8 x 16 mm BOLT - round head, square neck, 3/8 NC x 1 inch WASHER -lock, 3/8 internal tooth BOLT - flange head, 3/8 NC x 3/4 inch BOLT - hex head, M10 x 25 mm NUT - hex, M6 BOLT - hex head, 3/8 NC x 1 inch WASHER - lock, M6 BOLT - round head, square neck, 318 NC x 2 inch SCREW - machine, #10 NC x 2 inch WASHER -lock, #10 NUT - hex, #10 NC SCREW - machine, #6 NC x 1 inch WASHER -lock, #6 NUT - hex, #6 NC SCREW - machine, #10 NC x 1/2 inch NUT - serrated flange, #10 NC NUT - hex, #10 NF WASHER -lock, 1/4 inch BOLT - flange head, 1/4 NC x 112 inch NUT - serrated flange, 1/4 NC NUT - hex, 1/4 NC

48 38 ENGINE ASSEMSLY 19 e...-_'6 20 " ~ ~( I H DE "-., I ~,...

49 39 PART ENGINE ASSEMBLY DESCRIPTION QTY SERIAL NOTES ENGINE - diesel, 73 hp naturally aspirated {include.s starter} 1 ENGINE - diesel, 76 hp naturally aspirated (includes starter) 1 ENGINE - diesel, 80 hp naturally aspirated (includes starter) 1 ENGINE - diesel, 96 hp turbocharged (includes starter) 1 ENGINE - diesel, 108 hp turbocharged (includes starter) 1 SUPPORT - front right 1 SUPPORT - front right 1 - Order according to Serial Number breaks shown except Tractor Serial No This unit is equipped with the same components as those units with Serial No and up. SUPPORT - front left, with decal (was 44432) 1 MOUNT ~ support 2 INSULATOR ~ front engine mounts 2 SUPPORT ~ rear 1 INSULATOR ~ rear engine mounts 2 WASHER ~ flat, 17/32 10 x 1 3/800 x 3/16 inch thick 1 WASHER ~ flat, 17/3210 x x 3/16 inch thick.4 SENDER - temperature, 1 SWITCH ~ temperature 1 FIITlNG ~ reducer bushing, 3/8 NPT x 112 NPT 1 SWITCH oil pressure 1 FITTING barbed, 112 NPT x 5/8 hose (heater) 1 FITTING - barbed elbow, 1/2 NPT x 5/8 hose (heater) 1 MUFFLER ~ naturally aspirated engine 1 MUFFLER naturally aspirated engine 1 CLAMP muffler. 1 TUBE - exhaust 1 MUFFLER - turbocharged engine 1 MUFFLER ~ turbocharged engine 1 CLAMP muffler 1 CAP - rain 1 FAN engine cooling 1 SPACER - ran 1 WASHER ~ hardened 4 BOLT - hex head, M10 x 90 mm..4 BELT fan / alternator 1 FITTING - barbed, 1/4 NPT x 5/16 hose (fuel line) 1 FITTING - barbed elbow, 1/4 NPT x 5/16 hose (fuel line) 1 STARTER ~ with decal, (Cummins # plus MacDon deca142130) 1 FILTER ELEMENT - oil (Cummins # ) 1 FILTER ELEMENT - fuel, primary, with water trap (Cummihs # ) 1 FILTER ELEMENT ~ fuel, secondary (Cummins # ) 1 ALTERNATOR see ~A1temator Mounting" 1 SHIELD - starter " " " " see note 1 see note 2 1. ForTurbo Engine, these items are used for Serial No and below, excepttractor Serial No For Naturally Aspirated Engine, these items are used for: Serial No and below Serial No. blocks to and to Serial No and above 2. For Turbo Engine, these items are used for Serial No and above, plus Tractor Serial No For Naturally Aspirated Engine, these items are used for Serial No to , except Serial No. blocks to and to

50 40 A B C D E F G H J K L M N PART ENGINE ASSEMBLY DESCRIPTION OTY SERIAL Hardware for illustration on page 38. BOLT - hex head, M12 x 30 mm WASHER -lock, M12 WASHER - flat M12 WASHER -lock, 1/2 inch NUT - hex, 1/2 NC BOLT - hex hd, 1/2 NC x 1 1/2' BOLT - hex hd, 112 NC x 1 % WASHER - flat, 17/32 inch 10 BOLT - hex head, 1/2 NC x 3 BOLT - hex head, M10 x 35 mm WASHER -lock, M10 NUT - hex, M10 BOLT -hex head, M12x 25 mm

51 ALTERNATOR MOUNTING 40 A 2 PART DESCRIPTION QTY SERIAL SUPPORT allernalor, Gummins # SUPPORT - alternator, Cummins # BOLT - hex head, M8 x 25 mm, Cummins # BOLT - hex head, MB x 35 mm Cummins # SPACER - mounting. Cummins # BOLT - hex head, M10x90 mm 1 BOLT - hex head, M10 x 95 mm 1 BRACE - alternator, Cummins # BRACE - alternator, Cummins # BOLT - hex head, MB x 45 mm 1 BOLT - hex head, M10 x 25 mm 1 AlTERNATOR - includes items 9 and 10 (Delco-Remy # ) 1 ALTERNATOR - Delco-Remy # NOTE: If a~ernator is not available order KIT which includes: Alternator plus items 4, 5 and 10 to fit this newer alternator. RETAINER - pulley. Cummins # PULLEY - alternator, Cummins # PULLEY - allemalor, Cummins # see note 1 see note 2 see note 1 see note 2 see note 1 see note 2 see note 1 see note Prod'n Prodn.- see note 1 see note 1 see note 2 NOTES: 1. Use these items with Delco-Remy altemator # Use these items with Delco-Remy alternator #

52 40B ENGINE SUPERSTRUCTURE 4 5 "'\. -.0 o o. r d 10, 3 1~ 9 2, 8 8 I I 8

53 41 PART ENGINE SUPERSTRUCTURE DESCRIPTION QTY SERIAL PANEL - front SUPPORT - radiator, left - with decal SUPPORT - radiator, right COVER - engine, turbocharged diesel (see Note 1) COVER - engine, naturally aspirated diesel (see Note 1) GROMMET - engine cover MOULDING - hand hold MOULDING - rad cap access SHROUD - fan, with seals (item 9) SHROUD - fan, with seals (item 9)... 1 SEAL - foam, fan shroud SEAL - foam, fan shroud MOULDING - aspirated pre-cleaner hose, turbo diesel only 1 MOULDING - fuel tank access A B C BOLT - round head, square neck, 3/8 NC x 3/4 inch NUT - lock, smooth flange, 3/8 NC distorted thread BOLT - flange head, 3/8 NC x 3/4 inch NOTES: (1) - Engine cover (item 4) includes items 5, 6, 7 and 10.

54 42 FUEL SYSTEM ~ _"

55 43 PART FUEL SYSTEM DESCRIPTION QTY SERIAL TANK fuel STRIP - tank bottom STRAP - tank SENDER -fuel, with gasket (was 21954).1 GASKET fuel sender CAp fuel tank HOSE-tank vent FASTENER - plastic tie HOSE - to filter. 1 CLAMp hose, '" """"'" """''''""'" "'" '" '" '" """"'" '" "'" '" """""."""" """,,7 FILTER - fuel vent line 1 FIniNG - barbed, 1/4 NPT x 3/16 hose....1 FIniNG - barbed, 1/4 NPT x 5/16 hose....1 HOSE - from engine return line....1 HOSE - from engine return line 1 HOSE - from engine return line, naturally aspirated engine only 1 CLIP - hose 2 BOWL - sediment.. 1 FlnlNG. barbed, 1/8 NPT x 5/16 hose ".. " """"".."""""""""""""" 1 HOSE - to engine fuel pump. 1 PANEL - see "Engine Superstructure" 1 HOLDER - hose see note 1 see note 2 see note 3 see note 4 see note 5 NOTES 1. For Turbo Engine, this item is used for Serial No and below, except Tractor Serial No For Naturally Aspirated Engine, this item is used for: Serial No and below Serial No. blocks and to Serial No and above 2. For Turbo Engine, this item is used for Serial No and above, plus Tractor Serial No For Naturally Aspirated Engine, this item is used for Serial No to , except Serial No. blocks to and to For Turbo Engine, this item is used for Serial No and below, except Tractor Serial No For Naturally Aspirated Engine, this item is used for Serial No and below. 4. For Turbo Engine, this item is used for Serial No and above, plus Tractor Serial No For Naturally Aspirated Engine, this item is used for Serial No to , except Serial No. blocks to and to For Naturally Aspirated Engine, this item is used for: Serial No. blocks to and to Serial No and above A B C D E NUT hex, 3/8 NC SCREW machine, #10 NC x 3/4 inch WASHER ~ lock, #10 BOLT - round head, short square neck, 3/8 NC x:y., inch - naturally aspirated engine only NUT -lock, smooth flange, 3/8 NC distorted thread - naturally aspirated engine only

56 44 ENGINE AIR INTAKrE _ " "'i':::"--1 c 27 E' o L- TRACTOR ~- TURBO DIE5~7'410 AND Up. I SERIAL NO. 2. D'

57 44A PART ENGINE AIR INTAKE DESCRIPTION QTY SERIAL CLEANER - engine air, with filter elements. 1 ELEMENT - filter, primary (outer) 1 ELEMENT - filler, safety (inner)... 1 NUT - wing. 2 VALVE - vacuator... 1 BAND - mounting, with hardware. 2 CONNECTOR 1/8 NPT FITTING - barbed, 1/8 NPT x 5/16 10 hose 2 HOSE - to service indicator INDICATOR - service PRE-CLEANER - with clamp. 1 TUBE - pre-cleaner. 1 HOSE air intake to engine, Turbocharged Diesel HOSE - air intake to engine, Naturally Aspirated Diesel CLAMP - hose (qty. 3 for Turbo Diesel Ser. No and up) 2 PRE-CLEANER - aspirated, with clamp... 1 HOSE - aspirated pre-cleaner. 1 CLAMP - hose ' ITEMS ARE FOR TURBO DIESEL, SER. NO AND UP' CLEANER - engine air, includes filter elements plus items 21 & 22 1 ELEMENT - filter, primary (outer) ELEMENT - filter, safety (inner). 1 VALVE - vacuator LATCH - cover CLAMP - plastic TUBE - reinforcement HOSE ELBOW - 45, inlet TUBE - pre-cleaner 1 HOSE ELBOW - 90, reducer, engine air intake SUPPORT - air cleaner HOSE - to service indicator ' * ' ' ' ' ' ' ' ' ' ' * ~ Order according to Serial Number breaks shown except Tractor Serial No ~98. This unit is equipped with the same components as those units with Serial No and up. A B C D E F NUT - serrated flange, 3/8 NC BOLT - round head. square neck, 3/8 NC x 3/4 inch NUT -lock, smooth flange, 3/8 NC distorted thread BOLT - flange head, 3/8 NC x 3/4 inch BOLT - round head, square neck, 5/16 NC x 1 inch NUT - lock, smooth flange, 5/16 NC distorted thread

58 446 ENGINE COOLING, '0 3 A <t--_'o Jt ~6

59 45 ENGINE COOLING PART DESCRIPTION QTY SERIAL A B RADIATOR. see NOTE 1 1 RADIATOR 1 RADIATOR 1 CAP. radiator 1 HOSE - upper rad 1 VALVE -drain 1 HOSE - lower rad 1 TUBE - connector. 1 CLAMP - hose 3 CLAMP - hose 1 TANK - coolant recovery, with cap and hose CLIP - hose 2 BOLT - flange head, 3/8 NC x 3/4 inch NUT -lock, smooth flange, 3/8 NC distorted thread NOTES: 1. Radiator (for machines with serial no and below): If unavailable, service with or Radiator PLUS Fan Shroud (page 41).

60 46 STANDARD AIR INTAKE SCREEN Serial No and below A "-8, I " ,-... ~ --,~~/ \ A B PART DESCRIPTION OTY SERIAL PAN lower, with seal (item 3) SCREEN - rear SEAL sponge BOLT - flange head, 3/8 NC x 3/4 inch NUT - lock, smooth flange, 3/8 NC distorted thread

61 47 B AIR INTAKE SCREEN WITH CLEANER Serial No and below c, s TOP VIEw,, J + B- -E VIEW Yo o PART DESCRIPTION QTY SERIAL A B C E J K L M N R PAN - lower, with seal SEAL - s~nge 1 SPROCKET - duct arm OUCT - main, with seals (item 10) CHAIN - roller, # MOTOR - electric.., PLATE - motor mount SPROCKET - motor SCREEN rear DUCT - arm SEAL - foam SHAFT - duct arm HOSE - to fan shroud HOSE - to main duct BUSHING - plastic LINK - connecting, #35 chain CLAMP - hose CLAMP - hose PLUG - plasuc BOLT - flange head, 3/6 NC x 3/4 inch NUT lock, smooth flange, 3/8 NC distorted thread PIN - cotter. 3/16 x 1 1/2 inch SCREW - pan head, #10 NC x 112 inch BOLT - round head, square neck. 3/6 NC x 3/4 inch SCREW round head, #8 NC x 5/16 inch BOLT - round head, square neck, 1/4 NC x 3/4 inch WASHER - flat, 9/32 inch ID NUT serrated flange, 1/4 NC WASHER flat, 7/32 inch ID SCREW - set, socket head. 5/16 NC x 3/8 inch

62 48 ESCREEN AIR INTA~86 and above Serial No "'-- 2 / ~.p"'. ~D... ~.~,"" D ~/" I " H G ~ ~~~/\ /~ \ A/ ':-..: / ';{~, I 17 0

63 PART AIR INTAKE SCREEN Serial No and above DESCRIPTION QTY SERIAL PAN -lower, with seal (nem 21) 1 SCREEN - rear 1 PLUG - plastic (for screen holes), Standard Air Intake Screen only 2 PLUG - plastic, lower pan see note (1) ITEMS 5-20: AIR INTAKE SCREEN CLEANER ATTACHMENT ONLY A B C E F G H J f HOUSING - duct, includes item 6 2 SEAL - foam, housing to screen 2 ROD - support 1 DUCT ASSEMBLY - includes items 9,10 and hardware E 2 DUCT ASSEMBLY - includes items 9,10 and hardware E 2 DUCT - arm 2 PIN - duct 2 PIN - duct 2 BUSHING - plastic 4 SPROCKET - duct drive 2 SPROCKET - duct drive 2 CHAIN - roller 1 LINK - connector 1 MOTOR - electric 1 STOP - motor 1 MOULDING - edge 4 HOSE - air 2 CLAMP - hose 2 SHIELD - plastic 1 SEAL - sponge 1 BOLT - flange head, 3/B NC x 3/4 inch NUT -lock, smooth flange, 3/B NC distorted thread BOLT - round head, square neck, 3/8 NC x 3/4 inch NUT - serrated flange, 3/8 NC RIVET - pop, 3/16 x inch grip range.. SCREW - hex washer head, 5/16 NC x 1/2 inch, thread cutting. SCREW - set, Allan socket head, 1/4 NC x 5/16 inch. SCREW - set, Allan socket head, 3/8 NC x 5/8 inch. WASHER -lock, ~ SCREW - machine, round slotted head, #8 NC x 5/16 inch NUT - jam, 318 NC.. Indicates where hardware passes through frame member NOTES: (1) Quantities for item 4: Air Intake Screen with Cleaner Attachment = 1 Standard Air Intake Screen = 5 (4 used to plug hose routing holes)

64 50 HEADER DRIVE M, 14 ~. I 22 I " /' ' "- 11~, _.', EH A ~ 37 GR I 10 17

65 51 PART HEADER DRIVE DESCRIPTION QTY SERIAL FITTING - reducer bushing, 3{8 NPT x 118 NPT CLAMP - hose VALVE - relief FASTENER plastic lie WASHER flat GUIDE - be~, lower FITTING elbow BUSHING - plastic HOSE - hydraulic, bevel gear box to relief valve BELT - header drive INSULATOR rubber PUl.LE;Y - idler WASHER - flat, (qty. 2 for serial no ) GUARD front pulley, with decals PUllEY ASSEMBLY see "Header Drive Pulley", page 54 1 BEVEL GEARBOX - see page DRIVWNE; - see page GUIDE - belt, upper _... 1 RETAINER - bett ARM - idler PIVOT - idler CYUNDER - header clutch, complete _ 1 SHAFT - header clutch cylinder TUBE - header clutch cylinder SEAL - oil, outer (for header clutch cylinder) _. _ 1 SEAL - oil, inner (for header clutch cylinder) RING - retaining, internal (for header clutch cylinder) O-RING - (for header clutch cylinder) 1 SPRING - extension PIN roll, 318 x 1 inch 1 PULLEY driver, 96 hp Turbo Diesel & 73 hp Naturaily Aspirated Diesel Engines 1 PULLEY driver, 76 hp Naturally Aspirated Diesel Engine BUSHING - split taper, with outer key KEY - 5/16 square x 2 inch SUPPORT - switch SUPPORT - switch 1 SWITCH - header drive belt SPACER COVER - gearbox shaft access PLUG - plastic SHIM - header pulley alignment AIR FITTING - lube SUPPORT - fan shield, see page QO A B c o E F G H I J K l M N P Q NUT hex, 5/8 NC SCREW - hex washer head, 5/16 x 112 thread cutting NUT lock, 518 NC dist. thread NUT -lock, smooth flange, 1/2 NC distorted thread WASHER - flat, 21/32 inch 1.0. WASHER - lock, 318 inch WASHER - lock, 1J2 inch WASHER - lock, 5/8 inch BOLT - hex hd, 5f16 NC x 1 1/4 in. BOLT - hex head, 318 NC x 1 inch NUT - serrated flange. 1/2 NC NUT serrated flange. 3/8 NC BOLT - round head, square neck, 318 NC x 3/4 inch BOLT - hex hd, 1/2 NC x 1114 inch BOLT - hex hd, 318 NC x 1 1/2 inch BOLT hex hd, 5/8 NC x 2 1/2 inch R S T U V W X Y Z f...v BOLT - hex hd, 1/2 NC x 2 1/2 inch BOlT- rnd hd, short sq. nk, 318 NC x 3f4 in BOLT - hex head, 318 NC x 4 1/2 inch NUT - lock, smooth flange, 318 NC dlst. thd. BOLT - hex head, 5/8 NC x 4 1/2 inch NUT - hex, 318 NC WASHER - flat, 13/32 inch 1.0. BOLT - hex head, 1/2 NC x 4 inch BOLT - flange head, 318 NC x 314 inch Indicates where hardware passes through frame member.

66 52 Header Drive BEVEL GEARBOX / ~i I., \. "-.!C)_.

67 52 A PART Header Drive BEVEL GEARBOX DESCRIPTION QTY SERIAL DRIVE - bevel gearbox, complete - includes items 2 to 19 1 BUSHING - rubber 1 GEAR - set. 1 SEAL - output, extension end SCREW - special, M14 x 45 mm SHAFT - output K~...4 SHAFT - input _. _.. _.. _..... _ SEAL - input FLANGE bearing 1 BEARING - tapered roller, cup and cone WASHER - blank SHIM KIT SCREW - hex socket head, M12 x 30 mm BOLT - hex head, M12 x 25 mm TUBE - extension..,.,.,..,.,,,, 1 HOUSING _ O-RING - gearbox to tandem pump 1

68 52 B DRIVELINE (Engine to Bevel H, ~17 ~frame 15 J, frame~,, J, G, E 3 \ 8 1 I 2 6 J SERIAL NO AND BELOW 14 c F

69 53 PART DRIVELINE (Engine to Bevel Gearbox) DESCRIPTION QTY SERIAL FAN - plastic SHIM - locking (Serial No and below, qty. = 4) 2 DRIVElINE - engine, complete with end yokes (see note 1) 1 DRIVELINE - engine, complete with end yokes PLATE - adapter, diesel engine HUB - spline DISC - fan mount FlnlNG - lube SHIELD - fan, with decals CROSS & BEARING KIT YOKE - end YOKE - engine end YOKE - gearbox end, spline bore, with lube fitting (no plate, see note 1) 1 YOKE - gearbox end, spline bore, with fan mounting plate.. 1 FITTING - lube, drive type FiniNG - lube, 45', 1/4 NF SUPPORT - fan shield,... 1 SUPPORT - driveline 1 U-BOLT WASHER - square , , , COO = A C D E F G H J K NUT - hex, 3/8 NF (phosphate coated) BOLT - hex head, 3/8 NF x 1 1/2 inch (phosphate coated) BOLT - hex head, 3/8 NC x 3/4 inch BOLT - hex head, 3/8 NF x 1 inch (phosphate coated) WASHER - lock, 3/8 inch NUT - serrated flange lock, 3/8 NC BOLT - round head, square neck, 3/8 NC x 3/4 inch NUT - lock, smooth flange, 3/8 NC distorted thread BOLT - hex head, 3/8 NC x 1 inch NOTES, (1) - May be subbed to newer component.

70 54 HEADER DRIVE PULLEY 4 9 t"f-+..!-/!l-j.~ /(7 ~@ti 'c A REf PART DESCRIP1lON QTY SERIAL A 200n C PUlLEY - with cups and rings (Items 2 and 3) CUP - bearing RING - retaining, internal SUPPORT - with shaft CONE - bearing, with seal WASHER - flat, hardened 1 NlfT - siolled hex, 3/4 NF 1 PIN - cotter. 1/8 x 1 inch ATT1NG -lube BOLT - hex head, 3/8 NC x 1 inch WASHER -lock, 3/8 inch

71 Tractor to 900 Series Headers DRIVELINE /" / PART DESCRIPTION QTY SERIAL NSS NSS YOKE - flange 1 CROSS & BEARING KIT YOKE & SHAFT (order 44987) 1 SHIELD - outer, with decal 1 BEARING - shield, consists of t\,'io halves (Walterscheid) 2 BEARING KIT - shield (Weasler) 2 'SHIELD. inner. 1 SUPPORT - shield (Watterscheid) YOKE & TUBE - (order 43707) 1 YOKE - spline bore, 1 3/8 x 21 teeth. with slide collar YOKE - spline bore, 1 3/8 x 21 teeth, clamp type OPT. JOINT ASSEMBLY - male half, includes items 1,2,3,4,5 1 JOINT ASSEMBLY - female ha~, includes items 2,5,6,8, NSS DRIVELlNE complete, includes items 10 and 11 Not Serviced Separately

72 56 NEUTRAL INTERLOCK & PINTLE ARMS./ 7 \ 6 \ ~./ 2 ~ 11 -:7) f Q ~,/ \ 5

73 57 NEUTRAL INTERLOCK & PINTLE ARMS PART DESCRIPTION aty SERIAL A B E G H J K L M N P R S T LOCK - neutral 1 ARM - pintle, with bushing (item 3) 2 ARM - pintle. with bushing (item 3) 2 BUSHING - rubber, used with item 2 2 BUSHING - rubber, used with item 2 2 PIN roll, 3/8 x 2 inch 2 PUMP - piston. see "Hydraulics: Triple Pump", page 65 A 1 BUSHING - plastic 2 SUPPORT - gearbox 1 SUPPORT with bushing (item 9),.".".",.,., """".. "",."",1 BUSHING - rubber, used with item 8 1 WASHER - flat..4 MOUNT - switch 1 SWITCH - neutral 1 SPRING - extension 1 CABLE ASSEMBLY 1 CABLE ASSEMBLY 1 DRIVE - gear, see "Bevel Gearbox", page 52 1 BOLT - hex head, 1/2 NC x 1 1/4 inch WASHER -lock, 1/2 inch SETSCREW - square head, flat point, 3/8 NC x inch NUT - hex, 1/2 NC NUT -lock, 112 NC distorted thread WASHER - flat, 17/32 inch 1.0. BOLT - hex head, 7/16 NC x 1 inch WASHER. lock, 7116 inch BOLT - hex head, 112 NC x 2 3(4 inch BOLT - hex head, 1/2 NC x 3 1(4 inch NUT - hex jam, 1/2 NC BOLT - hex head, 3/8 NC x inch NUT - hex, 3/6 NC NUT - lock, smooth flange, 3/8 NC distorted thread & 1245QO

74 58 STEERING & GROUND SPEED Serial No and above NOTE: For machines with serial number and below, see "Steering & Ground Speed", page 90. 9,,

75 59 STEERING & GROUND SPEED Serial No and above PART DESCRIPTIDN QTY SERIAL A B C D E F G H J K Nf ARM - steering, with bushing (item 2) BUSHING - rubber PIVOT - steering CARRIER - steering, with bushing (item 2) BUSHING - plastic WASHER - flat SUPPORT - steering arm 1 BAR - control, ground speed 1 BAR - control, left, with bushing (item 2) (to front pintle arm) 1 BAR - conlrol, right, with bushing (item 2) (to rear pintle arm)... 1 CHAIN - steering INSULATOR - rubber WASHER - flat see note (1) LEVER - ground speed, see "Ground Speed Lever" 1 SHAFT - steering, see "Steering Column" PINTLE ARM see "Neutral Interlock & Pintle Arms" BAR - control, ground speed 1 PAD - friction SPRING - compression WASHER - flat, 17/32 inch I.D. BOLT - round head, square neck, 1/2 NC x inch BOLT - hex head, 1/2 NC x 3 1f2 inch NUT - hex. 1/2 NC NUT - lock, 1/2 NC distorted thread WASHER - lock, 1/2 inch BOLT - hex head, 1/2 NC x 2 1f4 inch BOLT - hex head, 1/2 NC x 4 inch PIN - cotter, 3/16 x 1 1f4 inch BOLT - round head, square neck, 1/2 NC x 5 inch Indicates where hardware passes through frame member NOTES: (1) - Quantity of item 13 varies as required for shimming. Nominal quantity is 3 RlH).

76 60 HYDRAULICS: HEADER DRIVE )}--' " '0 / ~<l~~ 14 V

77 61 PART HYDRAULICS: HEADER DRIVE DESCRIPTION QTY SERIAL A B C D E VALVE - header drive block, includes items SEAL KIT - repairs ~ cartridge in header drive valve block BLOCK only FITTING - adapter, 718 O-ring x 5/8 tube 1 FITTING - tee, 1 1/16 O-ring x 3/4 tube x 3/4 tube 1 HOSE - hydraulic, pressure to female coupler 1 HOSE - hydraulic, pressure to female cqupler 1 HOSE _hydraulic. return from male coupler 1 HOSE hydraulic, return from male coupler 1 FITTING - connector 1 WASHER - dished 2 COUPLER - quick disconnect, female, 1/2 NPT 2 O-RING - for coupler PLUG - dust.2 COUPLER - quick disconnec~ male, 1/2 NPT 2 CAP - dust 2 HOLDER - hose 1 FITTING - connector 1 HOSE - pressure to male coupler 920, 930 and 940 Headers 1 HOSE - pressure to male couple~ - 9S0 Header only 1 FITTING - elbow 1 HOSE - hydraulic, pressure - pump to block 1 LINE - hydraulic, pressure - to male coupler 1 LINE - hydraulic, pressure - to male coupler.. 1 LINE - hydraulic, return - coupler to filter 1 LINE - hydraulic, return - block to filter (not exactly as shown) 1 LINE hydraulic, return - block to filter. 1 FITTING -tee 1 FILTER ASSEMBLY -with head 1 FILTER element only, see note 4 re: substitution 1 HOSE - hydraulic, return - filter to tank 1 FITTING - connector 1 VALVE check 1 PUMP - hydraulic, see page 65 A 1 VALVE - N.C., header drive block 1 VALVE _P.O. relief, header drive block (stamped 1.0. #2155) 1 FLOW CONTROL, header drive block 2 SETSCREW - for flow control VALVE - shuttle, header drive block 1 VALVE regulator, header drive block 1 COIL - OS, 12VDC, header drive block.. 1 FASTENER - plastic tie 2 BOLT - round head, square neck, 318 NC x inch BOLT flange head, 1/4 NC x 3/4 inch NUT -lock, smooth flange, 3/8 NC distorted thread NUT - serrated flange, 318 NC NUT - hex jam, 112 NF (see nole 1) (see note 2) (see note 3) (see note 2) (see note 3) NOTES: 1.For machines with serial number and below (plus serial numbers and 94757), when ordering Valve Block (Item 1), also order Hydraulic line (Item 19). 2.Serial number and below plus serial numbers and Serial number and above except serial numbers and Pressure rating on MacDon fitter element is not adequate for this application.

78 62 HYDRAULICS, CYLINDER CONTROL. / ~11,. I 19. \ 3. /?) A \ 3 23 ~'ftl,;_25 E o 31

79 HYDRAULICS: CYLINDER CONTROL 62 A PART DESCRIPTION QTY SERIAL VALVE - cylinder control block, with reel lift - includes items SEAL KIT - repairs one cartridge in cylinder control valve block 1 BLOCK only FITIING - connector 2 FITTING - connector 2 FITTING - elbow 2 HOSE - pressure, pump to valve 1 HOSE - valve to left header lift cylinder 1 HOSE -left header lift cylinder to right header lift cylinder 1 HOSE - valve to right header lift cylinder 1 HOSE - valve to reel lift coupler 1 HOSE ~ valve to reel lift coupler 1 FIniNG - connector 1 WASHER - dished 1 COUPLER - quick disconnect, male (reel lift) 1 CAP - coupler 1 GROMMET - hose protector 2 GROMMET - hose protector 2 HOSE - valve to tank 1 HOLDER - hose 2 HOSE - valve to oil cooler 1 HOSE - valve to header clutch cylinder 1 FASTENER - cable tie 5 LINE - hydraulic, tandem pump 1 FITTING - lee 1 FITIlNG - connector 1 FILTER - oil, with head 1 ELEMENT - filter 1 NOTE: Pressure rating on MacDon filter element is not adequate for this application. FILTER - oil, with head - high pressure OPT ELEMENT - filter - high pressure OPT FIniNG - tee, tapped 1 SWITCH - oil pressure 1 HOSE - oil cooler to filter. 1 FiniNG elbow, 3/4 NPT x 5/8 tube, 2 HOSE _ fi~er to lank 1 HOSE - pump charge pressure 1 VALVE - check, 90 psi 1 CYLINDER ~ left, header lift - 3" bore 1 CYLINDER -left, heeder lifl- 3" bore 1 SEAL KIT - for cylinder or see page 63 A for kit contents COOLER - oil - NPT ports 1 COOLER - oil - JIG fittings 1 SUPPORT - coolers, left 1 SUPPORT - coolers, right 1 LATCH - cooler mount 1 CONDENSER - see "Air Conditioning", page 26 1 CYLINDER - header Clutch, see "Header Drive", page 50 1 PUMP - see page 65 A 1 SHIELD - valve 1 CYLINDER - right, header lift ~ 2.5" bore 1 CYLINDER - right, header lift - 2.5" bore 1 SEAL KIT - for cylinder or see page 63 B for kit contents

80 62 B _53 -J :,; ~ E / C 32 E 8

81 63 PART HYDRAULICS: CYLINDER CONTROL DESCRIPTION QTY SERIAL A B C E F G VALVE - N.C. (ports 5-3 & 5-5) 2 VALVE - relief (stamped 1.0. #2126) 1 VALVE - 3W 2P (ports 5-2 & S-6) 2 VALVE - 4W 2P (port 5-4) 1 VALVE - N.O. (port 5-1) 1 COIL - OS, 12VDC 6 NUT - special, machined 1 RESTRICTOR ~ flow, header clutch cylinder 1 RESTRICTOR - flow, to slow rate of Headers lift and drop (install in bottom port of item 31) FiniNG - straight connector, two-speed units.4 FiniNG - 45 elbow, single speed units 4 SUPPORT - coolers, welded assembly 1 SUPPORT - coolers, welded assembly 1 SUPPORT - cooler mount stiffener 1 KIT - header drop module OPT BOLT - flange head, 3/8 NC x 3/4 inch BOLT - round head, square neck, 3/8 NC x 1 1/2 inch NUT -lock, smooth flange, 3/8 NC distorted thread BOLT - flange head, 1/4 NC x 3/4 inch BOLT round head. square neck, 3/8 NC x 314 inch NUT - hex jam, 1/2 NF NUT -wing

82 63 A Header Lift Cylinder 3.0" BORE SEAL KIT PART DESCRIPTION QTY SERIAL SEAL KIT - 3" bore, for header lift cylinders & Includes the following: O-RING BN - 3" OD x 2-5/8" ID O-RING BN -1-1/8 OD x 7/8" ID O-RING BN - 3" OD x 2-314" [D..... _ BU WASHER - 3" OD x 2-3/4" ID _ 1 U CUP. L B-2" OD x 1-5/8" ID x 3/8" long _ 1 WIPER MT - 1-5/8" ID x 2-1/8 00 X 5/16" long

83 Header Lift Cylinder 2.5" BORE SEAL KIT 63 B PART DESCRIPTION QTY SERIAL SEAL KIT - 2.5" bore, for header lift cylinders & Includes the following: BU WASHER - 2-1/2" 00 x 2-1/8" 10 ",.., 2 O-RING BN - 2-1/2" 00 x 2-1/8" 10 " " "... 1 O-RING BN - 1-1/8 00 x 7/8" 10, O-RING BN " 00 x 2-1/4" 10 " ".. "".. 1 BU WASHER - 2-1/2" 00 x 2-1/4" 10 _ U CUP. L 8-2" 00 x 1-5/8" ID x 3/8" long ".. "." ".. 1 WIPER MT - 1-5/8" 10 x 2-1/8 00 x 5/16" long,,., 1

84 64 HYDRAULICS: TRACTION DRIVE 29 " " \, 5 " =;:;\ " 21'--,V' " 1, o / 0 31 / " ", J fil I' tij:

85 65 PART HYDRAULICS: TRACTION DRIVE DESCRIPTION QTY SERIAL A B C FITTING elbow, 314 tube x 1 1/16 O-ring O-RING - for 1 1/16 fitting HOSE - hydraulic - to left wheel molor, rear port 1 HOSE - hydraulic - to left wheel molor, front port 1 PAD - foam 5 HOSE - hydraulic - to right wheel motor, rear port 1 HOSE - hydraulic - to right wheel motor, rear port 1 HOSE - hydraulic, case drain from motors. 2 FiniNG - tee HOSE - hydraulic, return FiniNG - lee.. 1 HOSE - hydraulic, return to tank.. 1 GROMMET HOSE - hydraulic - to right wheel molor, front port 1 HOSE - hydraulic - to right wheel motor, front port 1 TANK - hydraulic 1 FIITING - barbed insert, 45~, 1 5f8 O riog 1 HOSE - hydraulic, suction _ 1 CLAMP - hose HOSE - filler to tank CAP - dipstick 1 STRAINER 1 PLUG - magnetic, with O-ring 1 SUPPORT - left SUPPORT - right RETAINER - tank mount STRIP - lower, tank mount STRIP - upper, tank mount FiniNG - elbow. 1 HOSE - vent 1 CLAMP - hose BREATHER HOSE - breather intake 1 FASTENER - plastic tie, 7 1/2 inch PROTECTOR - hose PUMP - see page 65 A FASTENER - plastic tie, 14 1/2 inch NUT - lock, smooth flange, 3/8 NC distorted thread BOLT - round head, square neck, 318 NC x 1 inch BOLT - round head, square neck, 318 NC x inch (see note 1) (see note 2) (see note 1) (see note 2) NOTES, 1. Serial number and below plus serial numbers and Serial number and above except serial numbers and

86 65A HYDRAULICS'. TRIPLE PUMP 72 /~o 42./' t-. 43 /"i."-~_ 44 ~-.. /~ 45 ~ '-..., 22 \ 33 "\ 35 \

87 HYDRAULICS: TRIPLE PUMP 65 B PART DESCRIPTION CTY SERIAL NOTE: Piston pump component quantities are per pump assembly RING - retaining,, SEAL shaft, (outer piston pump only) WASHER - flat, X 2 x 5/64 inch 1 RING - retaining 2 BEARING RACE - thrust..2 BEARING thrust... 1 SPACER - shaft, (inner piston pump only) 1 SHAFT - drive, (outer piston pump only) 1 HOUSING ASSEMBLY 1 BEARING - needle 1 BEARING - needle, trunnion 2 BEARING RACE - trunnion bearing 1 + * O-RING D. x 3132 inch thick, (see NOTE 1) 1 WASHER - flat, 1 x 1 39/64 X 3/64 inch 1 SEAL shaft, trunnion 1 COVER seal 1 COVER O ring, (see NOTE 1) 1 * COVER trunnion 2 * SCREW - #10 x 3/8 inch, special,4 CAM PLATE - with cross-hole in trunnion 1 SHAFT - drive (inner piston pump only) 1 ROTATING KIT ASSEMBLy 1 PLATE - valve 1 PiN-roil GASKET-backplate PIN dowel 2 BACK PLATE ASSEMBLY 1 BEARING - needle 1 RELIEF VALVE KIT - includes items BOLT - hex head, 318 NC x 2 inch 2 BOLT - hex head, 318 NC x inch 2 PLUG ASSEMBLY 2 a-ring -7/81.D. x3/32 inch 2 SPRING - relief valve 2 VALVE ASSEMBLY - relief, 5025 psi. 2 O-RING D. X 1/16 inch, inner piston pump to gear pump 1 BOLT - hex head, 3/8 NC x 1 1/4 inch 2 WASHER fla~ 39 x 68 x 6 mm 2 COUPLER - outer pump to inner pump (includes lock ring, item 69) 1 RING - lock 1 BOLT - hex head, 1/2 NC x inch 2 O-RING x 1/16 inch, outer piston pump to inner piston pump 1 PUMP - triple, complete 1 PUMP - triple, complete 1 PUMP - triple, complete 1 PUMP - piston, outer 1 PUMP - piston, outer 1 PUMP - piston, inner 1 PUMP - piston, inner 1 PUMP - double gear, header drive - see page 65 C SEAL KIT - for piston pump, includes all items marked + (see NOTE 1) SEAl KIT - pintle assembly, for piston pump, includes all items marked * (see NOTE 1) NOTES: 1. To prevent mismatching of parts, tractors with serial number and below must be upgraded with seal kil42189 (0). Units with this seal kit already installed may be identi1ied by two covers (item 18) instead of one.

88 65 C HYDRAULICS: DOUBLE GEAR PUMP I I 8 10 I 0. I 12 j I. -- ~}) '10.. ' i I :» J, : :II g" J ' '::' i I. ~,I, ::11 I I j I j j qr l! Ie :» 0 8~,..- ~1]JO 5, 32, \ 32 \ 39 \ 38 37

89 65 D PART HYDRAULICS: DOUBLE GEAR PUMP DESCRIPTION QTY SERIAL PUMP - double gear (Eaton #25387-RAE), part of Triple Pump For other triple pump components, see page 65 A. BACK PLATE O-RING 4 BODY - rear 1 GEAR 1 GEAR ASSEMBLY - rear idler. 1 KEY - round " PLATE - wear SEAL - bearing O RING moulded GASKET back up 2 PLATE - adapter WASHER - flat 1 BODY - lronl 1 GEAR ASSEMBLY drive, spline 1 GEAR ASSEMBLY - front idler 1 PLATE ASSEMBLY - Iront SEAL - shaft 1 BOLT - 12 point flange head, 5/16 NC x 4 3/4 inch SEAL KIT incl. all items marked +, for pump (Eaton #25387 RAE} PUMP - doudie gear (Eaton #26511 RAB). part of Triple Pumps & For other triple pump components, see page 65 A. BACK PLATE ' a-ring 4 BODY - rear, 1 GEAR 1 GEAR ASSEMBLY - rear idler KEY - round 1 PLATE - wear 2 SEAL - balance 2 GASKET - back-up 2 PLATE - adapter 1 WASHER - flat 1 BODY - Iron!... 1 GEAR ASSEMBLY - drive, spline 1 GEAR ASSEMBLY front idler 1 PLATE ASSEMBLY -front 1 SEAL - shaft 1 BOLT -12 point flange head, 5/16 NC x 5 3/4 inch 8 PLUG 1 WASHER.4 SEAL KIT - incl. all items marked ", for pump (Eaton #26511 RAB)

90 65 E HYDRAULICS'. TWO-SPEED WHEEL MOTOR / -' / / 18...!...TI-' I,y!, pi 20 SEE NOTE ON J' \!./,O / 12 \ PAGE'"... I / 11 _/~... J 0nt~d5\Ii ~,,/" I'%J/ ~-, ',~ \ I 10 I~~~("'/\, ::;,;<~_~...,?1 \ \~\\:,oaf, I 11 I~ ~::,\! \ I :@f /... / 14 l~ ~, ~\' nt. / 15 _Y ~@ / 16 ~ ~rd/9 '"

91 65 F HYDRAULICS: TWO-SPEED WHEEL MOTOR PART DESCRIPTION QTY SERIAL MOTOR - wheel, hydraulic piston type, complete. MOTOR - wheel, hydraulic piston type, complete. MOTOR - wheel, hydraulic piston type, complete RING - retaining " SEAL-shaft 1 3 WASHER - flat, X2 x 5164 inch RING - retaining BEARING RACE -thrusl BEARING -thrust SHAFT - drive 1 9 HOUSING ASSEMBLY BEARING - needle BEARING - needle, trunnion BEARING RACE - trunnion bearing O-RING - 1 7/16I.D. x 3/32 inch thick (see NOTE 1) WASHER - flat, 1 x 1 39/64 X 3/64 inch SEAL-shaft, trunnion COVER - seal COVER - 0-rin9 (see NOTE 1) COVER - trunnion SCREW - #10 x 3/8 inch, special CAM PLATE - with cross-hole in trunnion 1 21 ROTATING ASSEMBLY (Eaton # ) 1 22 PISTON ASSEMBLY 1 23 SPiDER 1 24 PIVOT - spider 1 25 WASHER-wave 1 26 BLOCK - piston 1 27 KEEPER - pin 1 28 PINS 3 29 WASHER - flat 2 30 SPRING 1 31 RING - retaining PLATE - valve 1 33 PIN - roll GASKET _back plate PIN - dowel 2 36 BACK PLATE ASSEMBLY 1 37 BEARING - needle 1 38 BOLT - hex head, 318 NC x 1114 inch SEAL KIT - for motor, includes all items marked + (see NOTE 1) SEAL KIT - pintle assembly, for motor, includes all items marked * (see NOTE 1) NOTES: 1. To prevent mismatching of parts, tractors with serial number and below must be upgraded with seal kit (*). Units with this seal kit already installed may be identified by two covers (item 18) instead of one.

92 66 TWO-SPEED DRIVE: LEVER / CABLE ASSEMBLY 4 c( EE 2 G, D" /, I >' 5 "c A 1 EE EE " 6 " 3 'F 7

93 66 A A B C D E F G PART TWO-SPEED DRIVE: LEVER I CABLE ASSEMBLY DESCRIPTION QTY SERIAL LEVER speed control WASHER - flat WASHER - flat KNOB - ball CABLE - control BOLT-hook 1 SHAFT - cross, see "Linkage Assembly", page BOLT ~ hex head, 1/2 NC x 2 inch NUT - hex, 1/2 NC BOLT - round head, square neck, 3/8 NC x 1 inch NUT - lock, smooth flange, 3/8 NC distorted thread NUT - hex 3/8 NC BOLT - hex head, 3/8 NC x 1 1/2 inch NUT - hex jam, 1/2 NC

94 66 B TWO-SPEED DRIVE: LINKAGE ASSEMBLY G, 5!! c~ ~DD 1 / /,, G

95 67 PART TWO-SPEED DRIVE: LINKAGE ASSEMBLY DESCRIPTION QTY SERIAL SHAFT - cross SHAFT - cross ROD - shift. 2 ROD - shift 2 CLEVIS - shift arm 2 ARM - shift, see "Two-Speed Drive: Wheel Motor Assembly 2 BAR - mounting BAR - mounting PLATE - lock A C D E F G NUT - hex, 1/2 NC BOLT - hex head, 3/8 NC x 1 1/4 inch NUT - hex, 318 NC BOLT - hex head, 1/2 NC x 2 1/4 inch BOLT - hex head, 3/8 NC x 3/4 inch NUT - lock, smooth flange, 3/8 NC distorted thread

96 68 TWO SPEED DRIVE.. WHEEL MOTOR ASSEMBLY 1 2 / 3 C G ~.~ 6 - H / 4 \ 8 _7 5

97 69 PART DESCRIPTION TWO SPEED DRIVE: WHEEL MOTOR ASSEMBLY QTY SERIAL A C D E F G H DRIVE power wheel, see page O-RING power wheel to motor seal MOTOR hydraulic, see page 65 E ARM - shift. with bushing (item 5) BUSHING - rubber 2 PIN - stmight FiniNG - elbow. 1 5/16 O-ring x 1 inch tube D-RING - for fitting FiniNG - elbow, 9/16 O-ring x 3/8 inch tube - R/H motor 1 FITTING long elbow, 9/16 O ong x 3/8 inch tube - UH motor C-RING - for 9/16 fitting BOLT - hex head, 1/2 NC x 3 inch BOLT - hex head, 5/8 NC x 1 3/4 inch NUT - hex, 5/8 NC BOLT - hex head, 1/2 NC x 1 1/4 inch WASHER - lock, 1/2 inch WASHER - lock, 5/6 inch NUT - lock, 1/2 NC distorted thread

98 70 SINGLE SPEED DRIVE: WHEEL MOTOR ASSEMBLY 1

99 71 SINGLE SPEED DRIVE: WHEEL MOTOR ASSEMBLY PART DESCRIPTION QTY SERIAL DRIVE ~ power wheel, see page O-RING - power wheel to motor seal MOTOR - hydraulic MOTOR - hydraulic O-RING - motor, internal SEAL - motor shaft FITTING - elbow. 1 5/16 O-ring x 1 inch tube O-RING - for 1 5f15 fitting FITTING - adapter, 3/4 O-ring x 3/8 inch tube G-RING - for 3/4 fitting FITTING - 45" elbow, 3/8 inch tube C D E F G BOLT - hex head, 5/8 NC x 1 3/4 inch NUT - hex, 5/8 NC BOLT - hex head, 1/2 NC x inch WASHER -lock, 1/2 inch WASHER - lock, 5/8 inch

100 72 MODEL 6 POWER WHEEL NOTE: Some units with serial No and up will have Model 7 Power Wheels. Model 7 Power Wheels may be identified as follows: 1. Hub (similar to item 8) on Model 7 has no webs. Model 6 has webs as shown. 2. Cover (similar to item 27) is made of cast iron. Model 6 cover is aluminium. For parts breakdown of Model 7 Power Wheel, see page 73 A & 73 B

101 73 PART MODEL 6 POWER WHEEL DESCRIPTION QTY SERIAL DRIVE - power wheel, complete: Single-Speed Drive 2 DRIVE - power wheel, complete: Single-Speed Drive 2 DRIVE - power wheel, complete: Two-Speed Drive 2 NOTE: Quantities below are per drive assembly. COUPLING - 13 teeth 1 SHAFT - input 1 SPINDLE - drive 1 SEAL - oil, BEARING - cone 1 BEARING - cup 2 BOLT - wheel, 9/16 NF 9 HUB power wheel 1 BEARING cone 1 BOLT - hex head, 318 NF x 1 7/8 inch Grade B 6 WASHER - flat 6 KIT - retaining ring, includes the following ring thicknesses: inch - Orange inch - Grey inch Dark Green inch - Plain inch - Brown inch- Dark Blue inch - Pink 1 NOTE: Select appropriate ring to provide 0 to end play. RING - retaining : 2 WASHER 2 SPRING - disengage 1 GEAR - ring 1 CARRIER ASSEMBLY - secondary 1 CARRIER ASSEMBLY - primary, power wheel only 1 CARRIER ASSEMBLY - primary, power wheel only : 1 GEAR - sun, primary, power wheel only 1 GEAR - sun, primary, power wheel only.. 1 WASHER - thrust 1 WASHER - thrust 1 PLUNGER - disengage 1 O-RING 1 BOLT - hex head, 5/16 NC x 1 inch 8 PLUG - pipe, magnetic 1 COVER - large 1 COVER - disengage 1 BOLT - hex head, 5/16 NC x 314 inch 2 RING - retaining

102 73 A MODEL 7 POWER WHEEL NOTE: Some units with serial No and up will have Model 6 Power Wheels. Model 6 Power Wheels may be identified as follows: 1. Hub (similar to item 11) on Model 6 has 6 webs. Model 7 has no webs as shown. 2. Cover (similar to item 28) is made of aluminium. Model 7 cover is cast iron. For parts breakdown of Model 6 Power Wheel, see page 72 & / 2 Cj~ 3 / 5 J 11 / o 0 '2 13 o / / / 6 7 / / OtJ(() 20 ~/ 22 / 28 / ti / 30 L ()O,.J 2. \ \ 32 31,,,"',

103 MODEL 7 POWER WHEEL 73 B PART DESCRIPTION QTY SERIAL DRIVE - power wheel, complete: Two-Speed Drive 2 Also includes brake components & 45619, (items from pages 76,77) and 0 on , (item 2 from page 68). NOTE: Quantities below are per drive assembly ",094 ", COUPLING -131eelh 1 SHAFT - input 1 SPINDLE - drive 1 SEAL - oil 1 BEARING - cone 1 BEARING - cup BOLT -.wheel. 9/16 NF 9 BOLT - hex head, 3/8 NF x 17/8 inch Grade 8 18 WASHER - flat 18 HUB - power wheel 1 BEARING - cup 1 BEARING - cone 1 WASHER -Ihrusl 1 WASHER-lock 1 NUT - bearing 1 RING - retaining 2 WASHER 2 SPRING - disengage 1 GEAR M ring 1 CARRIER ASSEMBLY - secondary 1 CARRIER ASSEMBLY - primary, RING - retaining 1 GEAR M sun, primary, 1 WASHER M thrust, 1 PLUNGER M disengage 1 O-RING 1 COVER M large 1 BOLT - hex head, 5/16 NC x 1 % inch 8 PLUG M pipe, magnetic 1 COVER - disengage 1 BOLT M hex head, 5/16 NC x 112 inch '

104 74 DRIVE WHEELS & TIRES 2 part DESCRIPTION QTY SERIAL B C See "Power Wheel", page 73 2 WHEEL-16.1 xw16c WHEEL-16.1 xw16c STEM - valve 2 NUT -wheel, 9/16 NF 18 TIRE L-16.1, r3: Goodyear 10 ply "Sure Grip" traction (bar) tread 2 TIRE L-16.1, I3: Goodyear 12 ply "Sure Grip" traction (bar) tread 2 TIRE L-16.1, R3: Bridgestone/Firestone "Turf & Field" 2 TIRE L-16.1, R3: Goodyear "Softrac II" 2 TIRE L-16.1, R3: Galaxy "Super Soft" 2 TIRE L-16.1, R3: Galaxy "Super Soft" 2 BOLT - hex head, 5/6 NC x 1 3/4 inch WASHER - lock, 5/6 inch

105 75

106 76 BRAKE ASSEMBLY I ):; I ~) /T x7/ 5 X 15-- I 13

107 77 BRAKE ASSEMBLY PART DESCRIPTION QTY SERIAL A B E G H J K L M N P S T V X - f LEVER ASSEMBLY - brake, with spacers 1 GRIP - orange 1 SWITCH - electrical. ", 1 CABLE ASSEMBLy WASHER - flat 3 WASHER - flat 2 CABLE - wire 1 BAND ASSEMBLY - brake (was 44324) 2 SPRING - extension 2 SUPPORT - brake band, Model 6 Power Wheel 2 SUPPORT - brake band, Model 7 Power Wheel 2 BRACKET - brake band, Model 6 Power'Mleel 2 BRACKET - brake band, Model 7 Power Wheel 2 LEVER - upper, Model 6 Power Wheel 2 LEVER - upper, Model 7 Power Wheel 2 LEVER -lower 2 LINK - connector. 2 BAR - support 2 NUT - lock, smooth flange, 3/8 NC distorted thread BOLT - round head, square neck, 3/8 NC x 2 inch BOLT - round head, square neck, 5/16 NC x 1 3/4 inch WASHER - fla~ 11/32 incl1l.d. NUT - hex, 5/16 NC BOLT - hex head, 5/16 NC x 3/4 inch NUT -lock, 5/16 NC distorted thread BOLT round head, square neck, 3/8 NC x 11/4 inch BOLT - hex head, 5/6 NC x 1 3/4 inch WASHER lock, 5/6 inch NUT - hex, 5/8 NC NUT - spring, 1/4 inch NUT - lock, 1/2 NC distorted thread BOLT - flange head, 3/8 NC x 3/4 inch BOLT - welded to tractor leg Indicates where hardware passes through frame member NOTE: For items 10, 11 and 12, components for Model 7 Power wheel may be used to replace components for Model 6 Power Wheel, but not the reverse.

108 78 ['L:-:::::- ~ CASTERS ~---J, 7 ---e ---.!1~6.5 FORKED 18 SERIAL NO I I I I I, '" L" I "... I J ", \.~ 4 ~ ". I E.~... ~'.' B \, 2 I4

109 FORKED CASTERS PART DESCRIPTION QTY SERIAL BW B 1570 CASTER - forked, for 16.5 tires 2 SHAFT - spindle WHEEL x W14C, for 16.5 tire. 2 WHEEL x W11C, for 16.5 tire. 2 BEARING ASSEMBLY - flange with bearing..4 BEARING - insert for assembly PIVOT - caster, with bushings ",_,. "... 2 BUSHING SPACER - quantity 4 for Serial Number and below WASHER....2 BEARING - thrust TIRE -16.5L-16.1, eight ply r1 Rib Implement STEM - valve FiniNG -lube.2 PLATE - friction 2 SPACER - tube. 2 WASHER - flat, 13/16 inch SPRING - compression CAP - plastic..2 WASHER - flat 2 KIT - anti-shimmy, includes two each of items 13 to 18 and hardware A and C. (Kit available through WholeGoods only) A B C o E F H J K L M BOLT - hex head, 1/2 NC x 6 inch. BOLT - round head, square neck 1/2 NC x 1 1/4 inch WASHER -lock, 1/2 inch NUT -lock, smooth flange, 1/2 NC distorted thread BOLT - hex head, 3/8 NC x 1 3/4 inch NUT - lock, smooth flange, 3/8 NC distorted thread BOLT - hex head, 112 NC x 2 1/4 inch BOLT - hex head, 5/8 NC x 1 1/2 inch WASHER - lock, 5/8 inch BOLT - hex head, 1/2 NC x 1 3/4 inch.. NUT - hex, 1/2 NC

110 FORKED CASTERS ";jl <'0 12_(jI) t /~(b 26/7.. ' 2S '1 '/ / ~ t:t~/44 42 do/, o L 6,,_5 f / / ~ M ~~~';" 10 8I!i 3' U::;;K\"' ~~

111 PART FORKED CASTERS DESCRIPTION QTY SERIAL WHEEL - 14 X 8KB, for 9.5 tire TIRE 9.5L-14, six ply r1 Rib Implement 2 BOLT - hex head, 1/2 NC x 1 1/2 inch 4 WASHER - lock, 1/2 inch BOLT - hex head, 5/8 NC x 1 1/2 inch WASHER - lock, 5/8 inch 4 WASHER - flat. 2 SPACER WASHER NUT slotted hex, 3/4 NF PIN - cotler, 3/16 x 1 1/4. 2 STEM - valve NUT hex, 1/2 NC 6 BOLT - hex head, 1/2 NC x 21/4 inch thread full length.. 2 CASTER forked CASTER - forked SHAFT 2 SEAL, 4 BEARING - cone 4 HUB - with bearing cups and studs BEARING - cup STUD - press in, 1/2 NF x 1 7/8 inch NUT - wheel, 1/2 NF _ 10 TUBE - mounting FITTING -lube 2 PIVOT caster, with bushings BUSHING - steel 4 BEARING - thrust BOLT hex head, 1/2 NC x 1 3/4 inch.... 2

112 82 FORMED CASTERS 8-4 ' B '

113 83 PART FORMED CASTERS DESCRIPTION QTY SERIAL TIRE - 8.5L-14, six ply 11 Rib Implement 2 TIRE - 9.5L-14, six ply 11 Rib Implement 2 PIVOT - caster (no bushings) PIVOT - caster, includes bushings. item BUSHING - sleel WASHER - lock, 112 inch 2 WASHER - lock, 5/8 inch BOLT - hex head, 5/8 NC x 1 1/2 inch CASTER - formed SPACER WASHER BEARING - cone, with seal 2 HUB - with bearing cups BEARING - inner cup BEARING - outer cup BEARING - cone WASHER - flat, 13/16 inch NUT - slotted hex, 3/4 NF PIN - cotter, 3/16 x 1 1/ CAP - dust WHEEL - 14 x 6 KB, for 8.5 tire WHEEL - 14 x 8 KB, for 9.5 tire BOLT wheel 10 STEM - valve 2 NUT - hex, 1/2 NC BOLT - hex head, 1/2 NC x 2 1/4 inch thread full length FiniNG lube. 2 BEARING - thrust 2 BOLT - hex head, 1/2 NC x 1 3/4 inch

114 84 SAFETY DECALS 10"'-~""'-'II" stop ltc,we WI"", <><neuir..--' 00.",-"_ -..rot...,. to _ <all... 00_.,."'..."_......""" 00<ltr<U otic"'_i. ",nov""'"". _or Ie> 01>«''''''... ''''...'""'l... ""l...-~... I 1 A [Q)b\INJ@~Wil ~~..~ R... ho._ en ground (It "'li"iio meclulnlcalloeko to.l",o going undo, unll. s.. Opo<_' M.nuol A[g~@~~ ~<!>L --!-,.,._wciu.,."..'"...n.. _, ;eo Iola<NM II... I T._~ 00"" "." ""Q'" "., "'...,...,.... sw.""i"'<''''' oom _'10<"0...L 00 _.., 10,tMt wo,"""'_,-"' ~.."'"..,,"" _,oot -...,.,-,,,,,. """...,- 1-"'... u,.....!l.-0<nn0. I 3 1I0TAIlNG DII/VEL/Nf """"" <>0 "'""... au,.."way/ 00""'"......,..,...._,_.. '.."..._,...'. I4 I"WARNING1! I,, I,.':='~::':"'=" ;:::..:.-::':-.-- ' -..., ' ~.:---._~.:::.:--~-" :0,:;,.._-~- I 14 I 6 I HYCRAUUC 0" c..., _y. f" ~ fu ' man.. U 0''''''~'''''. ""~O-'I'("1lI <>o.eity:., 'u". '",,-' u.s. g.llo... JI I 1iI ~ ~ dl k ~I i ~~@ RIGERANT 134a COMPRESSOR OIL c.~'~.~""... $ANOEN sp,., pag; O'L s.meo VI"""""'" ta<iiniclan ""'y. U" or 011>0< "" >01...".nty. 7 I AI'Il7~OOI!II!I;i ~ ~~.- ~ I 10 I 8 I AWb\WilINJ~INJ~ I II( ~To.-.old I/'lJ"'Y. $1Op on~~. t>oi... O\>Oning po... drive..,.iom..- K_ all shields In pl.e. Cl-OSltD coo...o."" system,...(" "",...,.. KEf' TIGHT..CoGton,...<_ '1"'"...,"'",~ _... ~ -MOR"'l- "" """"-..'"' " M. "" Rt,~""l.I"'.."._..._......"... _ '<me... '...lor CJD ONLY to.-i," r>oi>"". -<"'---- _t..-..."'_--...l 'ongoo. A~' I1lI'iJU\1I~~ 11 I I 13 j ~ ~ II! ~@ 50B.=, 12 I _. To oyold r.futt Of _lit front Imp<o_ Of ~"u" m8clr1,... OSWllkln:,. RMd lire e>p.ot.,... ",."".r. ~d """"'" on...,.1)' 1n.1n>Ction. II you do not Ir... mon~.i. OlI!a1<'l... hom.,... "'.10'. ~. Co IItltt.-..cl p.",ons to _01. tho J. R_..,.,...1Jon ith.1i 0~,.1<n.nnuolly. o. E~... liiot.u..i., olgn I~.'.llod""" Iog;_ S. "'.k._... I. oloa. 01 mod>lr>o be""..-.t.riing engine on<! duri"9 _o~on. a. Keep rldofl elf IIro maoehino. 7. 1<_.. oirloid. In ploeo r>d.i.oy '" m<>yin~ a. OI-'9"l1O ""Ide< "..,... pullr.~smlulon In _01.pply pori< bl'ob"""..oii to<.11 "",...,.. o>op boloio tor<ing _'101". pooltion., ~. 0<> _ MMco. odjvst...tiric.,. olo.~.. ""plv~ ",,,,,,",,, willl...g;... ""'~ing 01 ~.y In Ignillo<t. 10. ~ moc:lron""'io<:~. bof...","'ing""._...,ml In IIro,.Iud po,,'lon. ". Vse.1ow """"'9 _",10...t>Iom.nd n."...~...9 IIgIrU _ ~.1"'9 on, d".y. ""... ptot>;bilod by,-- --.j J 9 I ~-_. _0ftIIh01o_ 2.-.nv_1o _"'_10 "'--" I>OeU"og wp. 11lm _.._ _....-.,..-"'... ""'.--..-~ ~ ""...-.._-- _"'_""ol 1Og <onih>i.

115 85 SAFETY DECALS PART DESCRIPTION QTY SERIAL DECAL - DANGER Steering/Neutral DECAL - DANGER: Header Lift Cylinder Stops DECAL ~ DANGER: Starting DECAL - DANGER Driveline DECAL - WARNING: Engine Compartment Hazards, UH DECAl- WARNING: Engine Compartment Hazards, R/H DECAL - WARNING: EnginefTransmission Driveline Hazards. DECAL - WARNING: Shields and Guards DECAL - WARNING: StartinglDriving Procedures DECAL CAUTION: Radiator Cap DECAL - CAUTION; General Safety Precautions DECAl- SAFETY: live With It DECAl- WARNING: Enginerrransmission Driveline Hazards. DECAL - WARNING: Hydraulic Oir Leaks ,1082QO

116 86 INFORMATION DECALS & LECTORS CIIlCUrf IIR AI(EFlS "'.-.0, -~o _...., ----' _._.. c,...". _.. c,_... c... "" "... ".~.-..' _", u._ 16-9 ENGINE OIl. ~ma'-_~ 10. au.. ot 11.0 U.s. <ill,.~..~~ INl'ERlO8 l.jgiit RADIO (MEMORY).~. INSTllUMENTI;."""" 25ANP "'RCON[). """" """""'"' - SQTSMrCH EMERGENCY EXIT RELEASE W.NO(lW l.<tches.a!,lo\le...~l"iig. PuSH.w<OOW OPEN [ ( SOD.~J 14 / """ '" f,t=f'--" ::0 I I3 10 ij I \ ~ ==.;.; ~ 8-[ITNTTJ / _.lack HERE 15 tnorauuc OIl cr laI1r. filla "FUlL" rra<k. I,U ciea' Q;I. ~imale 'e!ili _ U.s. gaiion$ --~ / /7 23 I BEVEL GEAR801: Fa'"In'II plug li_cf~!jill _SAE8SN-l4QgMlOII.~...-1 lin or \ U.s. quail 5 Dr. la1i'l!o9 P"HufI,-, HI psi (132 kp.) Rear. g.5 ~ PI' (70 kp') lu" pol (35 kp.) IMPORTANT ro m_ ~ano""' ~_. ~~ V * """'" '"""" e:f] V 18 Front: A..., / 24 TIre lnflml on PrefSUI" 19 pal (132 kpi) 10 pol (70 kpi)

117 87 PART INFORMATION DECALS & LECTORS DESCRIPTION QTY SERIAL DECAl- Warning Lights DECAL -Ignition Sw"ch DECAL - Console DECAL - Header Lift DECAL - Reel Lift DECAL - Cab Circuit Breakers DECAL - Emergency Exit DECAL - Header Height Gauge,. DECAL - Patents DECAL - 50 Hour Grease DECAL - Driveline Grease DECAL - Diesel Fuel Only DECAL - Jack Here DECAL - Engine Oil (Order 45420, page 85) DECAl- Hydraulic Oil (Order 45419, page 8S) DECAL - Bevel Gear Box (Order 45420, page 85) DECAL - Refrigerant R-12 (for R134A order decal 45420, page 85) DECAL - Anti-Sway Block Positions LECTOR - red (was 26694) LECTOR - Day-Glow orange LECTOR - amber LECTOR - Slow Moving Vehicle Sign DECAL Header Height Gauge. DECAL - mark, Header Height Gauge. DECAL - tire pressure. DECAL - tire pressure a a- A SCREW - self tapping, hex washer head, 1/4 NC x 1/2 inch PAINT PAINT - black, spray can (25-35 Gloss Level). PAINT - black, 1 litre (25-35 Gloss Level).. PAINT - black, spray can (55-65 Gloss Level). PAINT - black, 1 litre (55-65 Gloss Level). PAINT - red, spray can PAINT - red, 1 litre PAINT - white, spray can PAINT - while, 1 litre a-

118 88 PRODUCT IDENTIFICATION DECALS (FOR SERIAL NO and up SEE PAGE 89 A) NOTE: If part numbers shown on these pages (88 & 89) are no longer available, you may sub up to the decals shown on pages ega & 89B. Be aware that the UH side of the tractor is now made up of three sections, instead of the two shown here \ b '----{ \E~~~~:::::::!~~~~~~ --:l' ~oc!@. FP.o,Io:I, IIIEW 5 I PART DESCRIPTION QTY SERIAL DECAL M UH side panel (153 mm high): rainbow stripe with MacDon 1 DECAL - RlH side panel (153 mm high): rainbow stripe with MaeDan 1 DECAL - cab door & R/H cab side panel (153 mm high): rainbow stripe 2 DECAL - cab front (105 mm high): rainbow stripe with MacDon 1 DECAL - Turbo, (turbocharged diesel only) 2 PLAQUE - Cummins Diesel Power 1 DECAL 9000 model number 2 DECAL model number...2 DECAL model number DECAL - cab door (153 mm high): WP stripe 1 DECAL - cab R/H side panel (153 mm high): WP stripe 1 DECAL - UH side panel (153 mm high): Westward 9000 stripe 1 DECAL - RlH side panel (153 mm high): Westward 9000 stripe 1 DECAL - UH side panel (153 mm high): Westward 9200 stripe 1 DECAL - RlH side panel (153 mm high): Westward 9200 stripe 1 DECAL - UH side panel (153 mm high): Westward 9300 stripe....1 DECAL - RlH side panel (153 mm high): Westward 9300 stripe

119 89 PRODUCT IDENTIFICATION DECALS (FOR SERIAL NO and up SEE PAGE 89 B) NOTE: Ifpart numbers shown on these pages (88 & B9) are no longer available. you may sub up to the decals shown on pages S9A & 89B. Be aware that the UH side of the tractor is now made up of three sections, instead of the two shown here va$w$iL, ---f ?ol {PRA I'?fE STAR I \--_ I PART DESCRIPTION QTY SERIAL DECAL - Prairie Star, side panels (153 mm high) 2 DECAL DECAL DECAL DECAL - Prairie Star, cab front (105 mm high) d I 43 P1UfTIlEP. -h TURBO PREmiER 2920 " 5 I.I~=~I DECAL - UH Premier 2900 (153 mm high) 1 DECAL - RIH Premier 2900 (153 mm high) 1 DECAL - UH Premier 2920 (153 mm high) 1 DECAL - RIH Premier 2920 (153 mm htgh) 1 DECAL - UH Premier 2930 (153 mm hi9h) 1 DECAL - RIH Premier 2930 (153 mm high) 1 DECAL - UH upper section stripe 1 DECAl RlH upper section stripe 1 DECAL - cab door (153 mm hi9h): UH Turbo 1 DECAL - cab RlH side panel (153 mm high): R/H Turbo 1 DECAL cab door & RlH side panel: stripe, naturally aspirated units 2 DECAL - cab front (105 mm high): Premier

120 89 A PRODUCT IDENTIFICATION DECALS SERIAL NO and up, --'~ ~::.<-.;,--:'-~ -.-._----- _ ~.. - :.:r!-::::. s=;...,... <T-:::"::.;: :.:...:;u;~~ ' \ 3 5SBI PART DESCRIPTION QTY SERIAL DECAL - UH side panel (192 mm high): rainbow stripe with MaeDon.. 1 DECAL - RlH side panel (192 mm high): rainbow stripe with MaeDan.. 1 DECAL - cab door & RlH cab side panel (192 mm high): rainbow stripe 2 DECAL - cab front (127 mm high): rainbow stripe with MaeDan 1 PLAQUE - Cummins Diesel Power 1 DECAL model number 2 DECAL model number DECAL - UH side panel (192 mm high): center section _I]]_W..,...~S_TW_P._RD / 11 \,-mc_w_es_tw-;-tp._rd_ 12 II m:jwestward I DECAL - UH side panel (192 mm high): WP Westward DECAL - RlH side panel (192 mm high): WP Westward DECAL - cab door & RlH cab side panel (192 mm high)...,... 2 DECAL - cab front (127 mm high): WP Weslwarn DECAL model number DECAL model number 2 DECAL - UH side panel (192 mm high): center section

121 PRODUCT IDENTIFICATION DECALS SERIAL NO and up 89 B 23 iiiiiiiiii...iii~ 27 PRI\IRlE STAR PART DESCRIPTION OTY SERIAL DECAL - UH side panel (192 mm high): Prairie Star 1 DECAL - RJH side panel (192 mm high): Prairie Star,,,,, 1 DECAL - cab door & RlH cab side panel (192 mm high) 2 DECAL - cab front (127 mm high): Prairie Star 1 DECAL model number 2 DECAL model number 2 DECAL - UH side panel (192 mm high): center section ~1~ I IIIIIPR~'ER PREMIERIIIII _1I1111 ~ DECAL - UH side panel (192 mm high): Premier 1 DECAL - RlH side panel (192 mm high): Premier 1 DECAL - cab door (192 mm high) 1 DECAL - cab front (127 mm high): Premier 1 DECAL model number 2 DECAL model number 2 DECAL - UH side panel (192 mm high): center section 1 DECAL - RlH cab side panel (192 mm high)

122 90 STEERING & GROUND SPEED Serial No and below NOTE: For machines with serial number and above, see Steering & Ground Speed". page 58. o o :::.-= "

123 PART STEERING & GROUND SPEED Serial No and below DESCRIPTION QTY SERIAL NUT - lock, 1/2 NC distorted thread NUT - hex, 1/2 NC WASHER - flat..... _... _. 5 WASHER - lock, 1/2 inch BOLT ~ hex head, 1/2 NC x 2 1/2 inch ARM - steering WASHER - flat, 17/32 inch I.D BUSHING - plastic ROD - to ground speed lever PIVOT - ground speed BOLT - round head, square neck, 3/8 NC x 3/4 inch NUT - lock, smooth flange, 318 NC distorted thread NUT - hex, 3/8 NC SPRING ~ compression WASHER - flat, 13/32 inch PIN - cotter, 3/16 x 1 1/4 inch WASHER - flat AIR CHAIN - roller CARRIER - steering BAR - left BAR - right SPRING - compression BOLT - hex head, 1/2 NC x 3 inch BOLT - hex head, 1/2 NC x 2 1f4 inch 2 PIVOT - steering

124 92 NUMERICAL LIST PART NO. PAGE PART NO. PART NO. PART NO. PAGE B A A B F A B B F B A B03 62 A B A A B B B B B B B B B

125 NUMERICAL LIST 93 PART NO. PAGE PART NO. PART NO. PART NO. PAGE B B B D B B F B F B F B F B F B B F B F B F B F B F B B B B B B B B B A A A A A A A A D D D D D D D A

126 94 NUMERICAL LIST PART NO. PAGE PART NO. PART NO. PART NO. PAGE : A A A A A F D B F A B ' A A A

127 NUMERICAL LIST 95 PART NO. PAGE PART NO. PART NO. PART NO. PAGE B B A A A A A A

128 96 NUMERICAL LIST PART NO. PAGE PART NO. PART NO. PART NO. PAGE F A A A A B : A A A A A A A A A A A A A A A A A A B A A A A A A A A A A B B B B B

129 NUMERICAL LIST 97 PART NO. PAGE PART NO. PART NO. PART NO. PAGE D B F B B B B F B B A A B F F B F : B F B F A A A A A A A A A A A A B B B B B B B B A A A A A A A A A A A A A A B B B B B B B B B B B B B B F B A A A D A B B W

130 98 Model 9000/4900/2900 Windrower (Tractor Unit) SUGGESTED STOCKING LIST P.C. PART DESCRIPTION SUGGESTED QTY. ORDER UNIT EXT. 2 UNITS 5 UNITS QTY PRICE PRICE GROUND SPEED LEVER - Parts Calaloq Pg BUSHING - plastic 2 4 CAB MC & BLOWER - Parts Calalog Pg O-RING CLEANER - air intake SWITCH - low pressure O-RING O-RING 1 2 MC - ENGINE GROUP - Parts Calalog Pg DRIER/RECEIVER BELT compressor drive 1 1 ENGINE ASSEMBLY - Parts Catalog Pg BELT - fan I alternator FILTER ELEMENT - oil FILTER ELEMENT - fuel, primary FILTER ELEMENT - fuel, secondary 1 3 ENGINE AIR INTAKE - Parts Calalog Pg 44 A FILTER - primary (ouler), Nat Asp FILTER - safety (inner), Nat. Asp FILTER - primary (outer), Turbo FILTER - safety (inner), Turbo 1 2 Order to suit engine type HEADER DRIVE - Parts Catalog Pg BUSHING - plastic BELT - header drive SEAL - oil, outer, clutch cylinder SEAL - oil, inner, clutch cylinder 1 1 BEVEL GEARBOX - Parts Catalog Pg 52 A BUSHING - rubber 2 4 DRIVELlNE: ENGINE/GEARBOX - Parts Catalog Pg CROSS & BEARING KIT 0 1 HEADER DRIVE PULLEY - Parts Catalog Pg CUP - bearing CONE - bearing, with seal 0 2 DRIVElINE: TRACTOR/HEADER - Parts Catalog Pg CROSS & BEARING KIT 1 3 NEUTRAL INTERLOCK - Parts Catalog Pg BUSHING - rubber 0 2 HYDRAULICS: HEADER DRIVE - Parts Catalog Pg FILTER - element 4 10

131 99 Model 9000/4900/2900 Windrower (Tractor Unit) SUGGESTED STOCKING LIST P.C. PART DESCRIPTION SUGGESTED CTY. 2 UNITS 5 UNITS ORDER UNIT EXT. CTY PRICE PRICE HYDRAULICS: CYLINDER CONTROL - Parts Catalog Pg 62 A SEAL KIT - UH lift cylinder SEAL KIT - RlH lift cylinder 0 1 HYDRAULICS: TRIPLE PUMP - Parts Catalog Pg 65 B BEARING - needle SEAL KIT - for piston pump SEAL KIT - pintle assembly 0 1 HYDRAULICS: WHEEL MOTOR - Parts Catalog Pg 65 F SEAL - shaft 0 1 WHEEL MOTOR ASSEMBLY - Parts Catalog Pg O-RING - powerwheev motor seal 0 1 PAINT - Parts Catalog Pg PAl NT - black, 1 litre, PAINT - white, 1 litre 1, PAINT - red, 1 litre 1 1

132

133

134 ) MocDon Industries ltd. 680 Moray Street Winnipeg, Manitoba R3J 383 (204) , Fax MocDon.lnc N.W. Conant Avenue Kansas City, Missouri (816) , Fax Issue 03/99 Sugg. Retail: $15.00 Printed in Canada \ )