A-Series A30-S and A30-D Pull-Type Mower Conditioners / A30-S, A30-D, and A40-D Self-Propelled Windrower Headers

Transcription

1 A-Series A30-S and A30-D Pull-Type Mower Conditioners / A30-S, A30-D, and A40-D Self-Propelled Windrower Headers Parts Catalog Revision A Original Instruction The harvesting specialists.

2 MacDon A40-D Self-Propelled Auger Header and A30-D Pull-Type Mower Conditioner Published: May, 2016 NOTE: Keep your MacDon publications up-to-date. The most current version can be downloaded from our website ( or from our Dealer-only site ( (login required).

3 TABLE OF CONTENTS Introduction...iii Abbreviations...iv Serial Number Breaks...iv Summary of Changes A-Series ( Rev. A)... v 1 Header Frame, Deflectors, and Shields A30-S Drive Components Left Hand A30-D Drive Components Left Hand A30-S and A30-D Drive Components Right Hand A40-D Drive Components Knife Drive Box Gearbox Conditioner Drive Conditioner Roll Drivelines Driveshields Cutting Components Knife Stub Guards A30-S and A30-D Reel A40-D Reel (Center Tube) A40-D Reel (Tine Tube) A40-D Reel Gearbox and Motor A30-S and A30-D Auger and Mounts A40-D Auger, Drive Motor, and Mounts A40-D Hydraulic Hoses and Couplers Articulated Hitch Drive Front Half Drivelines Hitch Hydraulics and Electrical Hitch Assembly Non-Articulated Pull-Type Hitch Hydraulics and Electrical Non-Articulated Pull-Type Pump/Gearbox Assembly Pull-Type Steering and Lift Cylinder Hydraulics Pull-Type Carrier Frame and Float Components Pull-Type Wheels and Tires Conditioner Rolls Roll Stop Linkages (SP Header) Lift Links and Header Stand (SP Header) Center Crop Deflector (SP Header) Pull-Type Forming Shields SP Header Forming Shields Lean Bar, Unplug Wrench, and Side Shoes Electrical Group Decals and Reflectors Two-Panel (Non-Text) Decals Product Identification Decals and Paint (Option) Drawbar Hitch (Option) Gauge Rollers i Revision A

4 TABLE OF CONTENTS 41 (Option) Hydraulic Header Angle Kit Articulated Hitch (Option) Hydraulic Header Angle Kit Standard Hitch (Option) Skid Shoes (Option) Tall Crop Dividers (Option) Three-Point Hitch Adapter (Option) Three-Point Hitch Linkage Articulated Hitch (Option) Truck Transport Hitch Index ii Revision A

5 Introduction This Parts Catalog lists all the replacement parts that can be ordered for MacDon A30-S and A30-D Pull-Type Mower Conditioners and MacDon A30-S, A30-D, and A40-D Self-Propelled Windrower Headers. When ordering, be sure to use the complete and proper part number. Some parts vary with machine type; be sure you are ordering the correct part number for your unit. Bold text is used to indicate updates made at the current revision level. With each new revision of the catalog, previous revisions are returned to regular text. Common hardware is not always illustrated. In these cases alphabetical references (call-outs) are used to designate position and description of these items. In this catalog, right-hand (RH) and left-hand (LH) are determined from the operator s seated driving position in the tractor or windrower cab. An arrow is sometimes used in illustrations to indicate forward position as shown below iii Revision A

6 Abbreviations A/R as required (quantity varies) C/W complete with CCW counterclockwise CW clockwise CSK countersink DK double knife DT distorted thread FLG flange GS grass seed MFA manual fore-aft I.D. inside diameter LH left hand (determined from Operator's position, facing forward) HFA hydraulic fore-aft NC national coarse thread NF national fine thread NSS not serviced separately O.D. outside diameter OPT optional PT pull-type (mower conditioner) REF reference, part number called up elsewhere in catalog RH right hand (determined from Operator's position, facing forward) RHSN round head, square neck or square neck carriage bolt RHSSN round head, short, square neck SMV slow moving vehicle SK singleknife SP self-propelled (windrower) header SPI serrations per inch (knife sections) UDK untimed double knife Serial Number Breaks The side of the serial number on which the dash ( ) appears determines whether the part is used "up to" or "after" the serial number given. Example: Used on machines up to and including serial number Used on machines including and after serial number iv Revision A

7 Summary of Changes A-Series ( Rev. A) This list covers changes made since the last revision ( Rev. A). Section 1 Header Frame, Deflectors, and Shields, page 1 2A30-SDrive Components Left Hand, page5 3 A30-D Drive Components Left Hand, page 9 6 Knife Drive Box, page Conditioner Rolls, page 109 Summary of Change Added to footnote: When replacing a shield a new shield support (MD #170600) is also required. Added NOTE with reference: Right-hand side knife drive components same as left-hand side, except as noted. Refer to Section 4 A30-S and A30-D Drive Components Right Hand, page 15. Added reference to existing NOTE. Updated illustration to Changed NOTE from Apply Loctite 243 adhesive or equivalent to splines before assembly to Apply Loctite adhesive or equivalent to output yoke (MD #100706) and input shaft (MD #100710) before assembly, to better describe needed action. Extension spring MD # superseded by spring assembly MD # Added footnote to MD #124530: Includes extension spring and two spring inserts. Removed #8 spring insert (MD #130529) from list as it is no longer required. Renumbered list. Updated illustration to to reflect changes. 35 Electrical Group, page 127 Added NOTE: For specific electrical harness parts, refer to Electrical Connector Parts Catalog (MD #169641). 42 (Option) Hydraulic Header Angle Kit Standard Hitch, page 143 Adjusted and removed duplicates from list. Added to footnotes so they were more clear. Internal Use Only Support SCR Tech Pubs Tech Pubs Tech Pubs ECN Support Tech Pubs v Revision A

8 HEADER FRAME, DEFLECTORS, AND SHIELDS 1 Header Frame, Deflectors, and Shields Revision A

9 HEADER FRAME, DEFLECTORS, AND SHIELDS Ref Part Number Description Qty CHANNEL STRIPPER (14 FT) CHANNEL STRIPPER (16 FT) CHANNEL STRIPPER (18 FT) 1 4 Serial Number STRIPPER FRONT (14 FT) STRIPPER FRONT (16 FT) STRIPPER FRONT (18 FT) STRIPPER FRONT (14 FT, FT GS) STRIPPER FRONT (16 FT) STRIPPER FRONT (18 FT) PAN MOLDED (14 FT) PAN MOLDED (16 FT) PAN MOLDED (18 FT) SHIM STRIPPER A/R ANGLE FINGER DOUBLE SUPPORT DEFLECTOR SHIELD WELDT, LH SHIELD WELDT, LH SHIELD WELDT, RH LATCH SHIELD PIN LEFT HAND PIN RIGHT HAND SUPPORT SHIELD PLATE COVER, RH END FRAME (A40-D ONLY) ANGLE STRIPPER EXTENSION PAN EXTENSION, GRASS SEED HEADER CHANNEL STRIPPER EXTENSION, GRASS SEED HEADER PLATE STRIPPER BAR SUPPORT, GRASS SEED HEADER PAN 14 FT. GRASS SEED HEADER PAN 16 FT. GRASS SEED HEADER 2 1. For grass seed headers: quantity = Use until part is depleted. 3. Replacement part for left-hand shield (MD #143344) once part is depleted. MD # left-hand shield is required for A40-D Headers with MD # reel drive motors. When replacing a shield a new shield support (MD #170600) is also required. 4. Not required for grass seed headers Revision A

10 HEADER FRAME, DEFLECTORS, AND SHIELDS Revision A

11 HEADER FRAME, DEFLECTORS, AND SHIELDS Ref 19 Part Number Description Qty DEFLECTOR LH, GRASS SEED HEADER DEFLECTOR RH, GRASS SEED HEADER GUIDE ENDSHIELD LATCH SUPPORT KNIFE DRIVE BOX MOUNT, LH SUPPORT KNIFE DRIVE BOX MOUNT, RH CASE MANUALS FASTENER CABLE TIE 1 Serial Number A WASHER FLAT, 17/32 I.D. X 1-1/16 IN. O.D. B NUT SMOOTH FLANGE, 3/8 NC, DT C BOLT RHSN, 3/8 NC X 1-1/4 IN., GR. 5 D NUT SMOOTH FLANGE, 5/16 NC, GR. 5 E NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT, GR. 5 F BOLT RHSN, 1/2 NC X 1-1/4 IN., GR. 5 G BOLT RHSN, 5/16 NC X 1 IN., GR. 5 H SCREW MACH, CSK SKT HD, 5/16 NC X 1 IN. J BOLT RHSN, 3/8 NC X 3/4 IN., GR. 5 K BOLT HEX HEAD, 3/8 NC X 1-1/4 IN., TFL, GR. 5 L WASHER FLAT, 13/32 I.D. X 13/16 IN. O.D. M NUT HEX, 3/8 NC, GR. 5 N NUT HEX, 1/2 NC, GR. 5 P BOLT HEX HEAD, 1/2 NC X 3-1/2 IN., GR. 5 Q NUT SERRATED FLANGE, 1/2 NC R BOLT HEX HEAD, M12 X 1-3/4 IN. X 75 MM LG. S NUT HEX, M12 X 1-3/4 IN. CLASS 10, STYLE 1 T 4761 WASHER FLAT, 13.5 MM I.D. X 35 MM O.D. X 4.5 MM THICK U BOLT HEX HEAD, 1/2 NC X 1-1/4 IN. GR.5 V WASHER FLAT, 17/32 IN. I.D. W RIVET BLIND, 1/8 X.125 X BOLT HEX,1/4NCX.625LG,GR.5ZNPL Y WASHER FLAT9/32I.D.X5/8O.D.ZNPL Z WASHER REGULAR LOCK 1/4 IN. NOM. I.D. ZN PL 5. European units 6. Welded Revision A

12 A30-S DRIVE COMPONENTS LEFT HAND 2 A30-S Drive Components Left Hand Revision A

13 A30-S DRIVE COMPONENTS LEFT HAND Ref Part Number Description Qty DRIVE KNIFE DRIVE BOX PULLEY KNIFE DRIVE BOX, DRIVE ARM DRIVE, KNIFE DRIVE BOX PIN KNIFEHEAD FITTING LUBE, ELBOW 90º, 1/8 IN. NPT SHIELD KNIFE DRIVE BOX ACCESS COVER BUSHING TAPER KEY PULLEY 1 Serial Number PULLEY KNIFE DRIVE PULLEY KNIFE DRIVE BELT KNIFE DRIVE PULLEY IDLER BAR ADJUSTER PULLEY AUGER DRIVE SPROCKET 22 TEETH SPROCKET 20 TEETH SUPPORT ADJUSTER BELT DOUBLE, AUGER DRIVE SPROCKET 60 TEETH BUSHING SPLIT TAPER, 1-1/2 IN. BORE KEY SPROCKET CHAIN ROLLER, #60H CONNECTOR LINK FOR CHAIN (MD #124619) 1 21 REF SUPPORT LH, AUGER BRACKET GEARBOX SUPPORT BEARING ROLLER RING SNAP FITTING LUBE, STRAIGHT, 1/4 1 NOTE: Right-hand side knife drive components same as left-hand side, except as noted. Refer to Section 4 A30-S and A30-D Drive Components Right Hand, page For service parts refer to Section 6 Knife Drive Box, page Refer to Section 16 A30-S and A30-D Auger and Mounts, page Revision A

14 A30-S DRIVE COMPONENTS LEFT HAND Revision A

15 A30-S DRIVE COMPONENTS LEFT HAND Ref Part Number Description Qty A BOLT HEX HEAD, 5/8 NC X 3 IN., GR. 5 B NUT HEX, 5/8 NC, DT C BOLT HEX HEAD, 5/8 X 1-3/4 IN., L9 D WASHER FLAT, 5/8 IN. I.D., HARDENED, L9 E BOLT SERRATED FLANGE HEAD, 3/8 NC X 1/2 IN. F BOLT RHSN, 1/2 NC X 2-1/4 IN., GR. 5 G BOLT HEX HEAD, 1/2 NC X 6-1/2 IN., TFL, GR. 5 H WASHER FLAT, 17/32 I.D. X 1-1/16 IN. O.D. J WASHER LOCK, 1/2 IN. I.D. K NUT HEX, 1/2 NC, GR. 5 L BOLT HEX HEAD, 1/2 NC X 1-1/4 IN., GR. 5 M NUT LK, SMTH FLG, 1/2 NC, DT N BOLT RHSN,1/2NCX1IN.,GR.5 P BOLT HEX HEAD, 1/2 NC X 3-1/2 IN., TFL, GR. 5 Q WASHER FLAT Serial Number NOTE: Right-hand side knife drive components same as left-hand side, except as noted. Refer to Section 4 A30-S and A30-D Drive Components Right Hand, page Revision A

16 A30-D DRIVE COMPONENTS LEFT HAND 3 A30-D Drive Components Left Hand Revision A

17 A30-D DRIVE COMPONENTS LEFT HAND Ref Part Number Description Qty KNIFE DRIVE BOX PULLEY KNIFE DRIVE BOX, DRIVE ARM DRIVE, KNIFE DRIVE BOX PIN KNIFEHEAD FITTING LUBE, ELBOW 90º, 1/8 IN. NPT SHIELD KNIFE DRIVE BOX ACCESS COVER BUSHING TAPER LOCK KEY WOODRUFF SPROCKET 122 TEETH, TIMING BELT BELT TIMING PULLEY 2B GROOVE BELT DOUBLE B PULLEY DRIVER BUSHING TAPER LOCK KEY 5/16 IN. SQUARE X 48 MM LONG SUPPORT CROSS SHAFT LEFT SUPPORT CROSS SHAFT RIGHT BEARING BALL, WITH LOCKING COLLAR FLANGE BEARING FLANGE BEARING, WITH FITTING HOLE FITTING ELBOW TUBE PLASTIC FITTING CONNECTOR FITTING UNION FITTING LUBE, ANGLE ADJUSTER 1 26 REF SUPPORT AUGER, LEFT SHAFT CROSS, 16 FT SHAFT CROSS, 18 FT TUBE CROSS-SHAFT 1 Serial Number NOTE: Right-hand side knife drive components same as left-hand side, except as noted. Refer to Section 4 A30-S and A30-D Drive Components Right Hand, page For service parts refer to Section 6 Knife Drive Box, page Refer to Section 16 A30-S and A30-D Auger and Mounts, page Revision A

18 A30-D DRIVE COMPONENTS LEFT HAND Revision A

19 A30-D DRIVE COMPONENTS LEFT HAND Ref Part Number Description Qty FITTING LUBE 2 31 REF GEARBOX CONDITIONER DRIVE SPROCKET 60 TEETH BUSHING SPLIT TAPER, 1-1/2 IN. BORE KEY SPROCKET CHAIN ROLLER, #60H CONNECTOR LINK FOR CHAIN (MD #124625) SPROCKET 20 TEETH SPROCKET ASSEMBLY BEARING BALL RING RETAINING BRACKET ADJUSTING, IDLER SPROCKET HUB MACHINED GUIDE PLASTIC 1 Serial Number NOTE: Right-hand side knife drive components same as left-hand side, except as noted. Refer to Section 4 A30-S and A30-D Drive Components Right Hand, page Refer to Section 7 Gearbox Conditioner Drive, page Revision A

20 A30-D DRIVE COMPONENTS LEFT HAND Revision A

21 A30-D DRIVE COMPONENTS LEFT HAND Ref Part Number Description Qty A BOLT HEX HEAD, 5/8 NC X 3 IN., GR. 5 B NUT HEX, 5/8 NC, DT C BOLT HEX HEAD, 5/8 X 1-3/4 IN., L9 D WASHER FLAT, 5/8 IN. I.D., HRND, L9 E BOLT SERRATED FLANGE HEAD, 3/8 NC X 1/2 IN. F BOLT HEX HEAD, 1/2 NC X 4 IN., GR. 5 G WASHER FLAT, 17/32 I.D. X 1-1/16 IN. O.D. H NUT HEX, 1/2 NC, GR. 5 J BOLT HEX HEAD, 1/2 NC X 4 IN., THREAD FULL LG, GR. 5 K BOLT RHSN, 3/8 NC X 1 IN. L NUT SMOOTH FLANGE, 3/8 NC, DT M NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT N BOLT RHSN,1/2NCX1IN.,GR.5 P NUT SERRATED FLANGE, 3/8 NC Q NUT SMOOTH FLANGE, 5/8 NC, DT R BOLT HEX HEAD, 1/2 NC X 1-1/2 IN. S WASHER LOCK, 1/2 IN. I.D. T WASHER FLAT, 21/32 IN. I.D. U BOLT RHSN, 3/8 NC X 1-1/4 IN. V BOLT RHSN, 5/8 NC X 2 IN. W BOLT HEX HEAD, 1/2 NC X 1-1/4 IN., GR. 5 X NUT HEX JAM, 1/2 NC Y BOLT CSK SOCK 1/2 NC X 1.75 GR. 5 ZN PL Z BOLT HEX HEAD, 1/2 NC X 6.5 IN., THREAD FULL LG, GR. 5 AA BOLT RHSN,5/8NCX1.5IN.GR.5 AB WASHER FLAT 2 Serial Number NOTE: Right-hand side knife drive components same as left-hand side, except as noted. Refer to Section 4 A30-S and A30-D Drive Components Right Hand, page Revision A

22 A30-S AND A30-D DRIVE COMPONENTS RIGHT HAND 4 A30-S and A30-D Drive Components Right Hand Revision A

23 A30-S AND A30-D DRIVE COMPONENTS RIGHT HAND Ref Part Number Description Qty KEY SPROCKET PULLEY AUGER BELT DOUBLE SPROCKET 60 TEETH BUSHING SPLIT TAPER, 1-1/2 IN. BORE KEY PULLEY 1 7 Serial Number PULLEY AUGER DRIVE PULLEY AUGER DRIVE ARM REEL DRIVE SPROCKET 22 TEETH, AS SHIPPED SPROCKET 20 TEETH, AS SHIPPED SPROCKET 19 TEETH, STORED IN RH END SHIELD WELL SPROCKET 26 TEETH OPT RING RETAINING, EXTERNAL BEARING BALL, C/W SEALS BRACKET ADJUSTER CHAIN ROLLER, #60H CONNECTOR LINK FOR CHAIN (MD #124625) BUSHING SPLIT TAPER, 1-3/8 IN. BORE SUPPORT ANGLE SPROCKET ASSEMBLY RING RETAINING BEARING BALL SHIELD SPROCKET AND CHAIN A30-S 13. All A30-D and A30-S serial number and up Revision A

24 A30-S AND A30-D DRIVE COMPONENTS RIGHT HAND Revision A

25 A30-S AND A30-D DRIVE COMPONENTS RIGHT HAND Ref Part Number Description Qty A WASHER SAE FLAT, 17/32 IN. I.D. X 1-1/16 IN. O.D. ZN PL B WASHER LOCK, 1/2 IN. I.D. C NUT HEX, 1/2 NC, GR. 5 D BOLT HEX HEAD, 1/2 NC X 1-1/4 IN., GR. 5 E NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT F BOLT HEX HEAD, 1/2 NC X 3-1/2 IN., TFL, GR. 5 G BOLT HEX HEAD, 1/2 NC X 2-1/4 IN., GR. 5 H BOLT ROUND HEAD, SQUARE NECK, 1/2 NC X 1 IN., GR. 5 J BOLT HEX HEAD, 1/2 NC X 6-1/2 IN., TFL, GR. 5 K BOLT RHSN, 5/8 NC X 2 IN., GR. 5 L NUT SMOOTH FLANGE, 5/8 NC, DT M BOLT RHSN,3/8NCX3/4IN.,GR.5 N NUT SMOOTH FLANGE, 3/8 NC, DT P BOLT HEX HEAD, 1/2 NC X 1-1/4 IN., GR BOLT HEX HEAD, 1/2 NC X 1.5 LG, TFL, GR. 5, ZN PL 15 Q WASHER FLAT, HARDENED R WASHER FLAT Serial Number 14. A30-S 15. All A30-D and A30-S serial number and up Revision A

26 A40-D DRIVE COMPONENTS 5 A40-D Drive Components Revision A

27 A40-D DRIVE COMPONENTS Ref Part Number Description Qty KNIFE DRIVE BOX PULLEY KNIFE DRIVE BOX, DRIVE ARM DRIVE, KNIFE DRIVE BOX PIN KNIFEHEAD FITTING LUBE, ELBOW 90º, 1/8 IN. NPT SHIELD KNIFE DRIVE BOX ACCESS COVER BUSHING TAPER LOCK KEY WOODRUFF SPROCKET 122 TEETH, TIMING BELT BELT TIMING PULLEY 2B GROOVE BELT DOUBLE B PULLEY DRIVER BUSHING TAPER LOCK KEY 5/16IN.SQUAREX48MMLONG SUPPORT CROSS SHAFT, LEFT SUPPORT CROSS SHAFT, RIGHT BEARING BALL, WITH LOCKING COLLAR FLANGE BEARING FLANGE BEARING, WITH FITTING HOLE FITTING ELBOW TUBE PLASTIC FITTING CONNECTOR FITTING UNION FITTING LUBE, ANGLE ADJUSTER SENDER SPEED 1 Serial Number NOTE: Right-hand side knife drive components same as left-hand side, except as noted in list. 16. For service parts refer to Section 6 Knife Drive Box, page Quantities for A40 Grass Seed 14 and 16 ft.= Quantities for A40 Grass Seed 14 and 16 ft.= Revision A

28 A40-D DRIVE COMPONENTS Revision A

29 A40-D DRIVE COMPONENTS Ref 27 Part Number Description Qty SHAFT CROSS, 14 FT SHAFT CROSS, 16 FT SHAFT CROSS, 18 FT TUBE CROSS-SHAFT FITTING LUBE 2 31 REF GEARBOX CONDITIONER DRIVE KNIFE DRIVE MOTOR OMS 100, C/W NUT & KEY SEAL KIT FOR MOTOR (MD #145767) CHANNEL PULLEY DOUBLEB PIN COTTER, 1/8 X 2.0 IN PLATE 20 1 Serial Number A BOLT HEX HEAD, 5/8 NC X 3 IN., GR. 5 B NUT HEX, 5/8 NC, DT C BOLT HEX HEAD, 5/8 X 1-3/4 IN., L9 D WASHER FLAT, 5/8 IN. I.D., HRND, L9 E BOLT SER FLANGE HEAD, 3/8 NC X 1/2 IN. F BOLT HEXHEAD,1/2NCX4IN.,GR.5 G WASHER FLAT, 17/32 I.D. X 1-1/16 IN. O.D. H NUT HEX, 1/2 NC, GR. 5 J BOLT HEX HEAD, 1/2 NC X 4 IN., TFL, GR. 5 K BOLT RHSN, 3/8 NC X 1 IN. L NUT SMOOTH FLANGE, 3/8 NC, DT M NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT N BOLT RHSN,1/2NCX1IN.,GR.5 P NUT SMOOTH FLANGE, 5/8 NC, DT NOTE: Right-hand side knife drive components same as left-hand side, except as noted in list. 19. Refer to Section 7 Gearbox Conditioner Drive, page Grass seed headers only Revision A

30 A40-D DRIVE COMPONENTS Revision A

31 A40-D DRIVE COMPONENTS Ref Part Number Description Qty Q BOLT HEX HEAD, 1/2 NC X 1-1/2 IN. R WASHER LOCK, 1/2 IN. I.D. S BOLT HEX HEAD, 1/4 NF X 3/4 IN. T WASHER LOCK, 1/4 I.D. U WASHER FLAT, 17/32 IN. I.D. V NUT HEX JAM, 1/2 NC W NUT HEX LOCK DT UNC X WASHER FLAT, 1 11/16 X 2.0 IN. O.D Y WASHER FLAT Z BOLT RHSN 1/2-13 X 1.25 GR5 ZP Serial Number NOTE: Right-hand side knife drive components same as left-hand side, except as noted in list Revision A

32 KNIFE DRIVE BOX 6 Knife Drive Box Revision A

33 KNIFE DRIVE BOX Ref Part Number Description Qty DRIVE SICKLE, COMPLETE YOKE OUTPUT SEAL OIL, OUTPUT SHAFT BUSHING BRONZE PLUG HEX SOCKET BUSHING STEEL NUT SPECIAL SHAFT INPUT SPACER 60 MM O.D O-RING SEAL OIL, INPUT SHAFT, 60 MM I.D BEARING ASSEMBLY CUP AND CONE PLUG OILDRAIN NUT LOCK, M55 X 2 IN PLUG BREATHER, C/W DIPSTICK BEARING ASSEMBLY CUP AND CONE NUT LOCK, M30 X 1.5 IN CAP DUST SHIM INPUT SHAFT BEARING ASSEMBLY CUP AND CONE PIVOT RING RETAINING, INTERNAL BUSHING BRONZE BOLT SOCKET HEAD, M10 X 50 MM TOOL KIT SICKLE DRIVE BOX DISASSEMBLY/ASSEMBLY A/R Serial Number NOTE: Apply Loctite adhesive or equivalent to output yoke (MD #100706) and input shaft (MD #100710) before assembly. 21. For placement refer to Sections 2 A30-S Drive Components Left Hand, page 5 or 5 A40-D Drive Components, page Revision A

34 GEARBOX CONDITIONER DRIVE 7 Gearbox Conditioner Drive Revision A

35 GEARBOX CONDITIONER DRIVE Ref Part Number Description Qty ASSEMBLY GEARBOX HOUSING GEARBOX, MATCHED LH AND RH PAIR KEY SQUARE RING RETAINING, EXTERNAL, 1-1/2 IN. SHAFT DIAMETER SHAFT MACHINED GEAR DRIVE SHAFT MACHINED BEARING ROLLER BEARING BALL SEAL OIL RING RETAINING, INTERNAL RING RETAINING, EXTERNAL GASKET GEARBOX HOUSING PLUG PIPE, SQUARE HEAD FITTING HYDRAULIC, 90º ELBOW, STREET, 3/8 IN. NPT FITTING HYDRAULIC, REDUCER VALVE RELIEF HUB TAPERED GEAR PINION MOTOR HYDRAULIC, KNIFE DRIVE SEAL KIT FOR HYDRAULIC MOTOR KEY 1/4 SQUARE 1 Serial Number A BOLT HEX HEAD, 3/8 NC X 1 IN., GR. 5 B NUT LOCK, 3/8 NC, DT C WASHER FLAT, 17/32 IN X 1-1/16 IN. O.D. D WASHER LOCK, 1/2 IN. I.D. E BOLT HEX HEAD, 1/2 NC X 1-1/4 IN., GR. 5 F NUT LOCK, 3/4 NF, DT G NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT H WASHER FLAT,13.5MMI.D.X38MMO.D.X6.4MMTHICK 22. Includes items # Includes key (MD #135500) Revision A

36 CONDITIONER ROLL DRIVELINES 8 Conditioner Roll Drivelines Revision A

37 CONDITIONER ROLL DRIVELINES Ref 1 2 Part Number Description Qty DRIVELINE COMPLETE, UPPER (14 FT) DRIVELINE COMPLETE, UPPER (16 FT) DRIVELINE COMPLETE, UPPER (18 FT) DRIVELINE COMPLETE, LOWER (14 FT) DRIVELINE COMPLETE, LOWER (16 FT) DRIVELINE COMPLETE, LOWER (18 FT) KEY SQUARE KEY DRIVELINE TO CONDITIONER ROLL YOKE CLAMP, UPPER DRIVELINE CROSS JOURNAL ASSEMBLY YOKE TAPERED SHAFT 14 FT SHAFT 16FT YOKE CLAMP, LOWER DRIVELINE YOKE FLANGE UNIVERSAL JOINT CONDITIONER ROLL END UNIVERSAL JOINT GEARBOX END 27 1 Serial Number A BOLT HEX HEAD, 1/2 NF X 1-1/4 IN., GR. 5 B WASHER FLAT,13.5MMI.D.X38MMO.D.X6.4MMTHICK C WASHER LOCK, 1/2 IN. I.D. D BOLT HEX HEAD, 1/2 NC X 2-3/4 IN., GR. 5 E NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT F BOLT HEX HEAD, 1/2 NC X 1-1/2 IN., GR. 5 G WASHER FLAT, 17/32 IN. I.D. X 1-1/16 O.D. H NUT HEX, 1/2 NC, GR A40-D 25. A30-D / A40-D 26. Quantities: A30-S = 3, A30-D and A40-D = A30-S Revision A

38 DRIVESHIELDS 9 Driveshields Revision A

39 DRIVESHIELDS Ref Part Number Description Qty PIN RETAINER LATCH SHIELD, RUBBER SHIELD DRIVELINE, UPPER, C/W DECAL (14 FT) SHIELD DRIVELINE, UPPER, C/W DECAL (16 FT) SHIELD DRIVELINE, UPPER, C/W DECAL (18 FT) ROD SHIELD HINGE (14 FT) ROD SHIELD HINGE (16 FT) ROD SHIELD HINGE (18 FT) SHIELD DRIVELINE, LOWER (14 FT) SHIELD DRIVELINE, LOWER (16 FT) SHIELD DRIVELINE, LOWER (18 FT) BRACKET SHIELD (14 FT) BRACKET SHIELD (16 FT) BRACKET SHIELD (18 FT) CHANNEL SHIELD BRACKET SHIELD LATCH HOOK, WITH BUSHING (EXPORT ONLY) BUSHING RUBBER (EXPORT ONLY) SPACER TUBE (EXPORT ONLY) GUIDE TOOL OPERATED LATCH (EXPORT ONLY) 1 Serial Number 28. Includes decal (MD #184385) Revision A

40 DRIVESHIELDS Revision A

41 DRIVESHIELDS Ref Part Number Description Qty A BOLT HEX HEAD, 3/8 NC X 1 IN., GR. 5 B NUT SMOOTH FLANGE, 3/8 NC, DT C WASHER FLAT, 13/32 I.D. X 1 IN. O.D. X 1/8 THK. D BOLT HEX HEAD 3/8 NC X 2.0 LG GR. 5 ZN PL E NUT HEX, 3/8 NC, GR. 5 F BOLT RHSN,1/2NCX1IN.,GR.5 G NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT H BOLT HEX HEAD, 1/2 NC X 1 IN., GR. 5 J WASHER LOCK 1/2 IN. K WASHER SAE FLAT, 17/32 IN. I.D. X 1-1/16 IN. O.D. ZN PL L BOLT RHSN,3/8NCX2.25IN.,GR.5,ZNPL M WASHER FLAT, 13/32 IN. I.D. N BOLT HEX HEAD, 1/2 NC X 2.25 IN., GR. 5, BLACK P BOLT RHSSN, 3/8 NC X 3/4 IN. GR. 5 Q WASHER FLAT, ROUND O.D, SQUARE BORE Serial Number Revision A

42 CUTTING COMPONENTS 10 Cutting Components Revision A

43 CUTTING COMPONENTS Ref Part Number GUARD KNIFE, ALL 29 Description Qty SK/DK GUARD KNIFE, OUTER (LH) GUARD KNIFE, OUTER (RH) GUARD KNIFE, SPECIAL (2ND-4TH AT DRIVE END(S) 3/ CLIP HOLD DOWN (25 PACK) KNIFE ASSEMBLY 14 FT. SK HDRS, CMPLT, 9 SER/FT. OPT KNIFE ASSEMBLY 16FT.SKHDRS,CMPLT,9SER/FT. OPT KNIFE ASSEMBLY 14 FT. SK HDRS, CMPLT, 14 SER/FT. 1/ KNIFE ASSEMBLY 16 SK HDRS, CMPLT, 14 SER/FT. 1/ KNIFEHEAD ASSEMBLY 31 1/ DISC KNIFEHEAD 1/ BEARING NEEDLE, KNIFEHEAD 1/ SEAL KNIFEHEAD 1/ O-RING KNIFEHEAD 1/ BAR CONNECTOR 1/ SECTION KNIFE, END (10 PACK) 2/ COARSE KNIFE SECTION 9 SPI (10 PACK) COARSE KNIFE SECTION 9 SPI (100 PACK) COARSE KNIFE SECTION BUSATIS 9 SPI (25 PACK) FINE KNIFE SECTION 14 SPI (10 PACK)) FINE KNIFE SECTION 14 SPI (100 PACK) FINE KNIFE SECTION BUSATIS 14 SPI (25 PACK) BAR CONNECTOR, 25 PACK 33 10/20 Serial Number 29. Quantities: 14 ft. SK = 25, 16 ft. SK = 28, 14 ft. DK = 21, 16 ft. DK = 24, 18 ft. DK = Quantities (individual pieces per header): 14 ft. SK = 27, 16 ft. SK = 30, 14 ft. DK = 25, 16 ft. DK = 28, 18 ft. DK = Includes disc (MD #113937), bearing (MD #100500), seal (MD #113222), and O-ring (MD #115670). 32. Quantities (individual pieces per header): 14 ft. SK = 59, 16 ft. SK = 65, 14 ft. DK = 52, 16 ft. DK = 59, 18 ft. DK = Install first ten after knifehead Revision A

44 CUTTING COMPONENTS Revision A

45 CUTTING COMPONENTS Ref Part Number Description Qty SK/DK KNIFE ASSEMBLY LH, FT DK HDRS, 9 SER/FT OPT KNIFE ASSEMBLY LH, 18 FT DK HDRS, 9 SER/FT OPT KNIFE ASSEMBLY LH, FT DK HDRS, 14 SER/FT 0/ KNIFE ASSEMBLY LH, 18 FT DK HDRS, 14 SER/FT 0/ COARSE KNIFE SECTION BOTTOM CSK, 9 SPI (10 PK) 0/ COARSE KNIFE SECTION BOTTOM CSK, 9 SPI (100 PK) 0/ COARSE KNIFE SECTION BOTTOM CSK, 9 SPI (25 PK) 0/ FINE KNIFE SECTION BOTTOM CSK, 14 SPI (10 PK) 0/ FINE KNIFE SECTION BOTTOM CSK, 14 SPI (100 PK) 0/ FINE KNIFE SECTION BOTTOM CSK, 14 SPI (25 PK) 0/ COARSE KNIFE SECTION TOP CSK, 9 SPI (10 PK) 0/ COARSE KNIFE SECTION TOP CSK, 9 SPI (100 PK) 0/ COARSE KNIFE SECTION TOP CSK, 9 SPI (25 PK) 0/ FINE KNIFE SECTION TOP CSK, 14 SPI (10 PK) 0/ FINE KNIFE SECTION TOP CSK, 14 SPI (100 PK) 0/ FINE KNIFE SECTION TOP CSK, 14 SPI (25 PK) 0/ GUIDE TOP, LH KNIFE 0/ BAR WEAR, LH KNIFE 0/ KNIFE ASSEMBLY RH, 14 FT DK HDRS, 9 SER/FT OPT KNIFE ASSEMBLY RH, DK HDRS, 9 SER/FT OPT KNIFE ASSEMBLY RH, 14 FT. DK HDRS, 14 SER/FT 0/ KNIFE ASSEMBLY RH, DK HDRS, 14 SER/FT 0/ GUARD CENTER 0/ BAR ADJUSTER 0/ GUARD TOP CENTER 0/ SHOE SHORT SHOE LONG 35 Serial Number 34. Quantities: 14 ft. = 2, 16 ft. = 1, 18 ft. = Quantities: 14 ft. = 1, 16 ft. = 2, 18 ft. = Revision A

46 CUTTING COMPONENTS Revision A

47 CUTTING COMPONENTS Ref Part Number Description A BOLT HEX HEAD, 3/8 NC X 5/8, TFL, GR. 8 B NUT FLANGE HEX HEAD, 3/8 IN. C 8218 BOLT RHSN, 7/16 NC X 1-1/2 IN., GR. 5 D NUT HEX, 7/16 NC, GR. 5 E SCREW BT HD, RIB NK, #12-24 NC X 1.05 IN. (50 PACK) 36 F NUT CSK, CENTER LOCK, #12-24 NC (50 PACK) 37 G SCREW BT HD, RIB NK, #12-24 NC X IN. (50 PACK) 38 H SCREW BT HD, RIB NK, #12-24 NC X 0.67 IN. (50 PACK) 39 J BOLT RHSN,1/2NCX1IN.,GR.5 K NUT LOCK, SMOOTH FLANGE, 1/2 NC, GR. 5 L SCREW 90 CSK SKT HD, #12-24 NC X 0.5 IN. (50 PACK) 40 M BOLT RHSN, 7/16 NC X 2-3/4 IN., GR. 5 N BOLT HEX HEAD, 3/8 NC X 1, STAINLESS STEEL Qty SK/DK Serial Number 36. Package of 1000 (MD #135633) / individual piece (MD #30668) 37. Package of 2000 (MD #135627) / individual piece (MD #30669) 38. Package of 1000 (MD #135631) / individual piece (MD #49671) 39. Package of 1000 (MD #135629) / individual piece (MD #30696) 40. Individual piece (MD #145246) Revision A

48 KNIFE STUB GUARDS 11 Knife Stub Guards Revision A

49 KNIFE STUB GUARDS Ref Part Number Description Qty SK/DK Serial Number B4692 KIT STUB GUARD CONVERSION, 14 FT. SK HEADER 41 B4955 KIT STUB GUARD CONVERSION, 16 FT. SK HEADER 41 B4956 KIT STUB GUARD CONVERSION, 14 FT. DK HEADER 41 B4715 KIT STUB GUARD CONVERSION, 16 FT. DK HEADER 41 B4957 KIT STUB GUARD CONVERSION, 18 FT. DK HEADER SPECIAL END GUARD NO TRASH BAR 42 4/ GUARD STUB BAR ADJUSTER GUIDE KNIFE GUARD STUB, CENTER 0/1 6 NSS CENTER GUARD, DOUBLE-KNIFE HEADERS 46 7 NSS END GUARDS, RH AND LH 47 A BOLT RHSN, 7/16 NC X 2-1/2 IN. B BOLT HEX HEAD, 3/8 NC X 3/4 IN., STAINLESS STEEL C BOLT HEX HEAD, 3/8 NC X 1 IN., STAINLESS STEEL D NUT HEX 7/16 NC E BOLT RHSN, 7/16 NC X 2-3/4 IN. 41. Kits available through Whole Goods only. 42. First four at drive end(s). 43. Quantities: 14 ft. SK = 26, 16 ft. SK = 29, 14 ft. DK = 22, 16 ft. DK = 25, 18 ft. DK = Quantities: 14 ft. = 30, 16 ft. = 33, 18 ft. = Quantities: 14 ft. SK = 30, 16 ft. SK = 33, 14 ft. DK = 29, 16 ft. DK = 32, 18 ft. DK = Includes guards (MD #118346, ), bar (MD #24980), and hardware (MD #50120, 18654, 21665). 47. Includes guard (MD #118347), bar (MD #34980), guide (MD #34359), and hardware (MD #30862, 50120, 18654) Revision A

50 A30-S AND A30-D REEL 12 A30-S and A30-D Reel Revision A

51 A30-S AND A30-D REEL Ref Part Number Description Qty B4693 KIT REPLACEMENT REEL BAT ASSY (14 FT) 48 B4694 KIT REPLACEMENT REEL BAT ASSY (16 FT) 48 B4863 KIT REPLACEMENT REEL BAT ASSY (18 FT) 48 Serial Number TUBE REEL (14 FT) TUBE REEL (16 FT) TUBE REEL (18 FT) SHAFT LH REEL SHAFT RH REEL TUBE TINE BAR, NARROW, 113 MM (14 FT) TUBE TINE BAR, WIDE, 161 MM (14 FT) TUBE TINE BAR, NARROW, 113 MM (16 FT) TUBE TINE BAR, WIDE, 161 MM (16 FT) TUBE TINE BAR, NARROW, 113 MM (18 FT) TUBE TINE BAR, WIDE, 161 MM (18 FT) DISC BUSHING HOLDER ARM REEL SPACER TUBE BAT REEL (14 FT) BAT REEL (16 FT) BAT REEL (18 FT) FINGER DOUBLE, RH OUTBOARD END FINGER DOUBLE BEARING CAM FOLLOWER BUSHING PLASTIC CLIP SPRING TOOTH PLUG REEL BAT CAM REEL BEARING REEL SHAFT, BALL, 1-3/8 IN. BORE Kits available through Whole Goods only. 49. To determine narrow (113 mm) or wide (161 mm) stagger, measure on the right-hand side of tube from end to third hole. Shown in illustration. 50. Includes plug (MD #124357). 51. Quantities: 14 ft. = 110, 16 ft. = 120, 18 ft. = Quantities: 14 ft. = 115, 16 ft. = 125, 18 ft. = Revision A

52 A30-S AND A30-D REEL Revision A

53 A30-S AND A30-D REEL Ref Part Number Description Qty FLANGE BEARING FLANGE BEARING, C/W GREASE FITTING SUPPORT LOWER BAR SHIM, CAM ADJUSTER ANGLE ADJUSTER SHIELD UPPER, LH REEL COVER CAM BEARING ACCESS WASHER RECTANGULAR 20 Serial Number A BOLT HEX HEAD, 5/8 NC X 1-1/4 IN., GR. 5 B WASHER LOCK, 5/8 IN. I.D. C BOLT RHSN, 5/16 NC X 2 IN., GR. 5 D BOLT RHSN, 5/16 NC X 1-3/4 IN., GR. 5 E BOLT RHSN,5/16NCX5/8IN.,GR.5 F BOLT HEX HEAD, 5/16 NC X 2-1/2 IN., GR. 5 G NUT LOCK, SMOOTH FLANGE, 5/16 NC, GR. 5 H NUT LOCK, HEX HEAD, 5/16 NC, DT J WASHER FLAT, 8.7 MM I.D. X 28.6 MM O.D. X 2 MM THICK K BOLT HEX HEAD, 5/8 NC L NUT HEX LOCK JAM, 5/8 NC, END DT M BOLT HEX HEAD, 1/4 NC X 2 IN., GR. 5 N NUT LOCK, HEX HEAD, 1/4 NC, DT P BOLT HEX HEAD, SER FLG, 3/8 NC X 5/8 IN., GR. 5 Q NUT SERRATED FLANGE, 3/8 NC R BOLT RHSN,3/8NCX1IN.,GR.5 S WASHER FLAT, 13/32 I.D. X 13/16 IN. O.D. T WASHER LOCK, 3/8 IN. I.D. U NUT HEX, 3/8 NC, GR. 5 V BOLT HEX HEAD, 1/2 NC X 3 IN., TFL, GR. 5 W NUT HEX, 1/2 NC, GR. 5 X BOLT HEX HEAD, 1/2 NC X 4 IN., GR. 5 Y WASHER FLAT, 17/32 I.D. X 1-1/16 IN. O.D. Z BOLT RHSN,1/2NCX1IN.,GR Revision A

54 A30-S AND A30-D REEL Revision A

55 A30-S AND A30-D REEL Ref Part Number Description Qty AA BOLT RHSN, 1/2 NC X 1-1/4 IN., GR. 5 AB NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT, GR. 5 AC BOLT RHSN,3/8NCX3/4IN.,GR.5 AD NUT LOCK, SMOOTH FLANGE, 3/8 NC, DT AE WASHER LOCK, 1/2 IN. I.D. Serial Number Revision A

56 A40-D REEL (CENTER TUBE) 13 A40-D Reel (Center Tube) Revision A

57 A40-D REEL (CENTER TUBE) Ref 1 Part Number Description Qty TUBE REEL (14 FT) TUBE REEL (16 FT) TUBE REEL (18 FT) SHAFT STUB, RH REEL CAM REEL BEARING REEL SHAFT, BALL, 1-3/8 IN. BORE FLANGE BEARING FLANGE BEARING, C/W GREASE FITTING COVER CAM BEARING ACCESS BUSHING TAPER LOCK, C/W OUTER KEY AND BOLTS KEY REEL DRIVE SHAFT 1 10 REF REEL GEARBOX AND MOTOR SUPPORT REEL, LH BUSHING RUBBER BAR SHIM, CAM ADJUSTER ANGLE ADJUSTER SHIELD REEL DRIVE SHAFT SHIELD UPPER, LH REEL 1 Serial Number A BOLT HH, 5/8 NC X 1-1/4 IN., GR. 5 B WASHER LOCK, 5/8 IN. I.D. C BOLT RHSN, 1/2 NC X 1-1/4 IN., GR. 5 D NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT, GR. 5 E BOLT RHSN,3/8NCX1IN.,GR.5 F WASHER FLAT, 13/32 I.D. X 13/16 IN. O.D. G WASHER LOCK, 3/8 IN. I.D. H NUT HEX, 3/8 NC, GR. 5 J BOLT HH,1/2NCX3IN.,TFL,GR.5 K NUT HEX, 1/2 NC, GR. 5 L BOLT HH,1/2NCX4IN.,GR.5 M WASHER FLAT, 17/32 I.D. X 1-1/16 IN. O.D. 53. Refer to Section 15 A40-D Reel Gearbox and Motor, page Revision A

58 A40-D REEL (CENTER TUBE) Revision A

59 A40-D REEL (CENTER TUBE) Ref Part Number Description Qty N BOLT RHSN, 1/2 NCX1IN.,GR.5 P BOLT HH, 3/8 NC X 2-1/2 IN., TFL, GR. 5 Q BOLT RHSN,3/8NCX3/4IN.,GR.5 R NUT LOCK, SMOOTH FLANGE, 3/8 NC, DT S BOLT HH,1/2NCX3IN.,GR.5 T WASHER LOCK, 1/2 IN. I.D. U WASHER FLAT Serial Number Revision A

60 A40-D REEL (TINE TUBE) 14 A40-D Reel (Tine Tube) Revision A

61 A40-D REEL (TINE TUBE) Ref Part Number Description Qty B4716 KIT REPLACEMENT REEL BAT ASSY (14 FT) 54 B4717 KIT REPLACEMENT REEL BAT ASSY (16 FT) 54 B4718 KIT REPLACEMENT REEL BAT ASSY (18 FT) 54 Serial Number TINE TUBE LH (14 FT) TINE TUBE LH (16 FT) TINE TUBE LH (18 FT) TINE TUBE CENTER (14-16 FT) TINE TUBE CENTER (18 FT) TINE TUBE RH (14 FT) TINE TUBE RH (16-18 FT) SHAFT LEFT END, INBOARD STAGGER (205 MM) SHAFT LEFT END, OUTBOARD STAGGER (158 MM) SHAFT CONNECTOR SHAFT CAM ARM REEL, OUTBOARD ARMS ARM REEL, INBOARD ARMS FINGER DOUBLE, RH OUTBOARD END FINGER DOUBLE BAT REEL (14 FT) BAT REEL (16 FT) BAT REEL (18 FT) SPACER TUBE PLUG REEL BAT CLIP SPRING TOOTH BEARING CAM FOLLOWER 6 NOTE: Top illustration: A-Type Bat, Outboard Stagger / Bottom illustration: B-Type Bat, Inboard Stagger. Bolt locations and orientations differ; be sure you are ordering the correct part. 54. Kits available through Whole Goods only. 55. To determine inboard (205 mm) or outboard (158 mm) stagger, measure distance between holes in shaft, shown in illustration. 56. To determine inboard (205 mm) or outboard (158 mm) stagger, measure distance between holes in shaft, shown in illustration. Quantities shown are for standard header. Grass seed headers have 7 reel bats instead of 6. Quantities that are multiples of 6 will be multiples of 7 for grass seed headers. 57. Quantities: 14 ft. = 132, 16 ft. = 147, 18 ft. = Includes plug (MD #124357) Revision A

62 A40-D REEL (TINE TUBE) Revision A

63 A40-D REEL (TINE TUBE) Ref Part Number Description Qty BEARING BALL, C/W LOCK COLLAR FLANGE BEARING FLANGE BEARING, C/W GREASE FITTING SPACER 9.8 MMID,15.7MMOD,15.5MMLG 59 3 Serial Number A BOLT RHSN, 5/16 NC X 2 IN., GR. 5 B BOLT RHSN, 5/16 NC X 1-3/4 IN., GR. 5 C BOLT RHSN,5/16NCX5/8IN.,GR.5 D BOLT HH, 5/16 NC X 2-1/2 IN., GR. 5 E NUT LOCK, SMOOTH FLANGE, 5/16 NC, GR. 5 F NUT LOCK, HH, 5/16 NC, DT G WASHER FLAT, 8.7 MM I.D. X 28.6 MM O.D. X 2 MM THICK H BOLT HH, 5/8 NC J NUT HEX LOCK JAM, 5/8 NC, END DT K BOLT HH, SER FLG, 3/8 NC X 5/8 IN., GR. 5 L NUT SERRATED FLANGE, 3/8 NC M BOLT SPECIAL, HEX HEAD, SHOULDER 60 N WASHER RECTANGULAR P BOLT RHSN 5/16-18 X 2.5-GR 5 ZP 59 Q BOLT HH5/16NCX2.0LGGR5ZP 59 NOTE: Top illustration: A-Type Bat, Outboard Stagger / Bottom illustration: B-Type Bat, Inboard Stagger. Bolt locations and orientations differ; be sure you are ordering the correct part. 59. Spacer (MD #170622) and bolts (MD # or 21569) replace bolt (MD #170190) at the shaft end, due to shearing. Illustration indicates the location and orientation of these replacement parts. Refer to Service Bulletin SB1431 when replacing bolt (MD #170190). 60. Refer to Service Bulletin SB1431 when replacing bolt (MD #170190) due to shearing Revision A

64 A40-D REEL GEARBOX AND MOTOR 15 A40-D Reel Gearbox and Motor Revision A

65 A40-D REEL GEARBOX AND MOTOR Ref Part Number Description Qty DRIVE ASSEMBLY GEARBOX 61 Serial Number HOUSING MACHINED, MATCHING SET GASKET REEL GEARBOX RING RETAINING, INTERNAL SHAFT MACHINED, REEL GEARBOX GEAR REEL GEARBOX BEARING BALL MOTOR HYDRAULIC, REEL DRIVE (2014 AND PRIOR) SEAL KIT FOR ROUND MOTOR (MD #124096) MOTOR HYDRAULIC, REEL DRIVE (2015 AND LATER) SEAL KIT FOR RECTANGULAR MOTOR (MD #155148) GEAR PINION WASHER FLAT, 1-1/16 I.D SENDER SPEED NUT SLOTTED HEX, UNEF KIT DRIVE, A40 REEL MOTOR (2014 AND PRIOR) 64 A/R KIT DRIVE, A40 GS REEL MOTOR (2014 AND PRIOR) 65 A/R FITTING ELBOW 90 HYD HOSE HYD, REEL MOTOR TO AUGER, 520 MM LG HOSE HYD CASE DRAIN, 1750 MM LG SHIELD WELDT, MD RED (LH) SUPPORT DOOR, HOLDS UP SHIELDS ON A FASTENER CABLE TIE, BLACK FITTING HYD TEE COUPLING FEMALE HYD. 3/8 FLAT FACE (GS ONLY) SUPPORT (GS ONLY) Includes housing (MD #143077), gasket (MD #143755), ring (MD #30882), shaft (MD #143089), gear (MD #143658), bearing (MD #30881), and hardware (MD #21491, 18638, 20077, 18637, 30228, 21572, 18596). 62. For A40-D Headers on M205 Windrowers 2014 and prior use kit (MD #170602), for grass seed use kit (MD #170619). Includes slotted nut (MD #137375). 63. Includes slotted nut (MD #137375). 64. For A40-D Headers on M205 Windrowers only. Does not include coupling (MD #135213) and support (MD #170616) as it is not required for this set-up. 65. For Grass seed A40-D Headers on M205 Windrowers only. Does not include fitting (MD # ) as it is not required for this set-up Revision A

66 A40-D REEL GEARBOX AND MOTOR Revision A

67 A40-D REEL GEARBOX AND MOTOR Ref Part Number Description Qty A SCREW HEX SOC HD 1/2-13 X 1.25-GR8-ZP B WASHER LOCK, 1/2 IN. I.D. C BOLT HEX HEAD, 3/8 NC X 1 IN., GR. 5 D WASHER LOCK, 3/8 IN. I.D. E NUT LOCK, SMOOTH FLANGE, 3/8 NC DT F BOLT HEX HEAD, 1/4 NC X 5/8 IN., GR. 5 G WASHER FLAT, 9/32 IN. I.D. H PIN COTTER, 5/32 X 1-1/2 IN. Serial Number Revision A

68 A30-S AND A30-D AUGER AND MOUNTS 16 A30-S and A30-D Auger and Mounts Revision A

69 A30-S AND A30-D AUGER AND MOUNTS Ref 1 Part Number Description Qty AUGER BALANCED (14 FT) AUGER BALANCED (16 FT) AUGER BALANCED (18 FT) KIT REPAIR, AUGER FLIGHTING EDGE FLIGHTING LH HELIX, 5 IN. WIDE, 18 FT. AUGER REPAIR FLIGHTING RH HELIX, 5 IN. WIDE, 18 FT. AUGER REPAIR FINGER AUGER SHAFT AUGER MOUNT SUPPORT AUGER, LH, A30-S SUPPORT AUGER, LH, A30-D SUPPORT AUGER, RH BEARING AUGER, 1-1/2 IN. BORE FLANGE BEARING, C/W 45 GREASE FITTING FLANGE BEARING 2 Serial Number A BOLT HEX HEAD, 5/8 NC X 3-1/2 IN., GR. 5 B NUT SMOOTH FLANGE, 5/8 NC, DT C BOLT HEX HEAD, 1/2 NC X 1 IN., GR. 5 D WASHER LOCK, 1/2 IN. I.D. E BOLT RHSN,1/2NCX1IN.,GR.5 F NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT, GR. 5 G BOLT HEX HEAD, 1/2 NC X 3 IN., GR. 5 H WASHER FLAT, 17/32 I.D. X 1-1/16 IN. O.D. J NUT HEX, 1/2 NC, GR Three-inch wide strips 67. LH helix fits right-hand side of header, welding required. 68. RH helix fits left-hand side of header, welding required. 69. Not exactly as shown Revision A

70 A40-D AUGER, DRIVE MOTOR, AND MOUNTS 17 A40-D Auger, Drive Motor, and Mounts Revision A

71 A40-D AUGER, DRIVE MOTOR, AND MOUNTS Ref 1 Part Number Description Qty AUGER BALANCED (14 FT) AUGER BALANCED (16 FT) AUGER BALANCED (18 FT) AUGER BALANCED, GRASS SEED (14 FT) AUGER BALANCED, GRASS SEED (16 FT) KIT REPAIR, AUGER FLIGHTING EDGE FLIGHTING LH HELIX, 5 IN. WIDE, 18 FT. AUGER REPAIR FLIGHTING RH HELIX, 5 IN. WIDE, 18 FT. AUGER REPAIR FINGER AUGER HUB AUGER MOUNT MOTOR HYD., AUGER DRIVE SEAL KIT FOR HYDRAULIC MOTOR (MD #143088) PLATE MOUNTING, AUGER MOTOR SUPPORT AUGER, LH BUSHING RUBBER WASHER FLAT SHAFT STUB, RH AUGER 1 Serial Number SUPPORT AUGER, RH BEARING BALL, 1-3/8 IN. BORE FLANGE BEARING, C/W GREASE FITTING FLANGE BEARING SHIM AUGER MOUNT A/R NUT SLOTTED HEX, UNEF SUPPORT AUGER, RH Three-inch wide strips 71. LH helix fits right-hand side of header, welding required. 72. RH helix fits left-hand side of header, welding required. 73. Includes slotted hex nut (MD #137375) and key units only Revision A

72 A40-D AUGER, DRIVE MOTOR, AND MOUNTS Revision A

73 A40-D AUGER, DRIVE MOTOR, AND MOUNTS Ref Part Number Description Qty A BOLT HEX HEAD, 5/8 NC X 3-1/2 IN., GR. 5 B NUT SMOOTH FLANGE, 5/8 NC, DT C BOLT HEX HEAD, 1/2 NC X 1 IN., GR. 5 D WASHER LOCK, 1/2 IN. I.D. E BOLT RHSN,1/2NCX1IN.,GR.5 F NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT, GR. 5 G BOLT HEX HEAD, 1/2 NC X 3 IN., GR. 5 H WASHER FLAT, 17/32 I.D. X 1-1/16 IN. O.D. J NUT HEX, 1/2 NC, GR. 5 K PIN COTTER, 1/8 X 2 IN. L BOLT RHSN,1/2NCX3IN.,GR.5 M BOLT HEX HEAD, 1/2 NC X 1-1/2 IN., GR. 5 N BOLT RHSN,3/8NCX1IN.,GR.5 P NUT LOCK, SMOOTH FLANGE, 3/8 NC, DT, GR. 5 Serial Number Revision A

74 A40-D HYDRAULIC HOSES AND COUPLERS 18 A40-D Hydraulic Hoses and Couplers Revision A

75 A40-D HYDRAULIC HOSES AND COUPLERS Ref Part Number Description Qty FITTING MALE ELBOW 45 HYD, C/W O-RING FITTING HYD TEE HOSE HYD, 1180 MM LG (14-16 FT) HOSE HYD, 1410 MM LG (18 FT) 75 1 Serial Number HOSE HYD, 460 MM LG HOSE HYD, 520 MM LG HOSE HYD, 4300 MM LG (14 FT) HOSE HYD, 4530 MM LG (16 FT) HOSE HYD, 4760 MM LG (18 FT) HOSE HYD, 4400 MM LG (14 FT) HOSE HYD, 4630 MM LG (16 FT) HOSE HYD, 4860 MM LG (18 FT) MOULDING HOSE PROTECTOR FITTING CONNECTOR HYD, C/W O-RING FITTING ELBOW 45, C/W O-RING COUPLER MALE, 3/4 IN. FLAT FACE SEAL KIT FOR COUPLER (MD #135314) FITTING CONNECTOR HYD, C/W O-RING COUPLER FEMALE, 3/4 IN. FLAT FACE FITTING ADAPTER HYD, C/W O-RING COUPLER FEMALE, 3/8 IN. FLAT FACE FITTING ADAPTER HYD, C/W O-RING VALVE RELIEF FITTING CONNECTOR HYD, C/W O-RING LINE HYDRAULIC FITTING CONNECTOR HYD, C/W O-RING HOSE HYDRAULIC, CASE DRAIN EXTENSION (18 FT) Reel motor top port to coupler. 76. Reel motor lower port to auger motor lower port. Not for use with A40-D Headers on M205 Windrowers. Use until part is depleted. 77. Reel motor lower port to auger motor lower port. Replacement part for hose (MD #124048), once part is depleted. Hose (MD #170603) is required for A40-D Headers on M205 Windrowers. 78. Reel motor lower port to coupler. 79. Auger motor top port to coupler. 80. Seal kit is discontinued. Order coupling/coupler. 81. Seal kit is discontinued. Order coupling/coupler. Quantity of 1 for foot grass seed headers Revision A

76 A40-D HYDRAULIC HOSES AND COUPLERS Revision A

77 A40-D HYDRAULIC HOSES AND COUPLERS Ref 21 Part Number Description Qty SUPPORT HARNESS/COUPLER (14-18 FT) SUPPORT HARNESS/COUPLER (16 FT GS ONLY) SUPPORT HARNESS/COUPLER (14 FT GS ONLY) COUPLER FEMALE HYD 1/2 IN. FLAT FACE SLEEVE HOSE FITTING MALE ELBOW 90, C/W O-RING COUPLER MALE, 1/2 IN. FLAT FACE SEAL KIT FOR COUPLER (MD #135508) COUPLER HYDRAULIC, 1/2 IN FEMALE FF FITTING CONNECTOR HYD, C/W O-RING COUPLER MALE, 3/8 IN. FLAT FACE SEAL KIT FOR COUPLER (MD #135237) FITTING ADAPTER HYD, C/W O-RING HOLDER HOSE DEFLECTOR HOSE STRAP VELCRO, HANGING FITTING ELBOW LINE HYDRAULIC LINE HYDRAULIC FITTING ELBOW HYD FITTING CONNECTOR HYD HOSE HYD (16 FT GS ONLY) HOSE HYD (16 FT GS ONLY) COUPLING FEMALE HYD 3/4 IN. FLAT FACE BULKHEAD COUPLING MALE HYD 3/4 IN FLAT FACE BULKHEAD MOULDING FRAME (UNIGRIP) MOULDING HOSE PROTECTOR 1 Serial Number FITTING ELBOW 90 HYD HOSE HYD, CASE DRAIN FITTING HYD TEE Seal kit is discontinued. Order coupling/coupler. 83. Required for reel drive motor (MD #155148) Revision A

78 A40-D HYDRAULIC HOSES AND COUPLERS Revision A

79 A40-D HYDRAULIC HOSES AND COUPLERS Ref Part Number Description Qty A BOLT RHSSN, 3/8 NC X 3/4 IN. B NUT LOCK, SMOOTH FLANGE, 3/8 NC, DT, GR. 5 C BOLT RHSN, 3/8 NC X 1-3/4 IN. D BOLT RHSN, 1/2 NC X 1 IN., GR. 5 E NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT, GR. 5 Serial Number Revision A

80 ARTICULATED HITCH DRIVE 19 Articulated Hitch Drive Revision A

81 ARTICULATED HITCH DRIVE Ref Part Number Description Qty SUPPORT COVER HITCH CLIP HOOK GUARD PIVOT MACHINING BUSHING 102 I.D. X 111 O.D. X 38 LONG FITTING LUBE 1/4-28 UNF RING EXT RETAINING PIVOT MACHINING, AUGER DRIVELINE HITCH DRIVELINE HITCH (CE) CROSS DRIVELINE, 1000 RPM PUMP YOKE DRIVELINE, 1000 RPM PUMP DRIVELINE SHIELD DRIVELINE, 1000 RPM PUMP REPAIR KIT DRIVELINE SHIELD, 1000 RPM PUMP A/R PUMP 1000 RPM SEAL KIT FOR PUMP (MD #142944) PUMP 540 RPM SEAL KIT FOR PUMP (MD #142945) FITTING SUCTION LINE PRESSURE FITTING ELBOW HYD FITTING ELBOW IN JIC IN. ADJ ORB HOSE PT AUGER HOSE SUCTION, PT AUGER CLAMP T BOLT CLAMP T BOLT JACK WASHER THRUST 1 Serial Number 84. For 1000 rpm front half drivelines, refer to Section 20 Front Half Drivelines, page Order this clamp if hose (MD #142939) is manufactured by Gates. 86. Order this clamp if hose (MD #142939) is manufactured by Parker or Aeroquip Revision A

82 ARTICULATED HITCH DRIVE Revision A

83 ARTICULATED HITCH DRIVE Ref 27 Part Number Description Qty DRIVELINE MAIN 540 RPM (NORTH AMERICA) DRIVELINE MAIN 540 RPM (EXPORT) KIT CE CONVERSION (EXPORT) 89 A/R Serial Number A BOLT RHSN 1/2 NC X 1.25 GR. 5 ZN PL B BOLT HH 1/2 NC X 2.0 LG GR. 5 ZN PL C NUT FLGSMOOTHFACE7/16NCGR.5ZNPL D NUT FLANGE DT SMOOTH FACE UNC E BOLT HEXHD3/8NCX1.0LGGR.5ZNPL F BOLT HH FLG (SER FACE) 3/8 NC X 1.0 GR. 5 ZN PL G WASHER SAE FLAT 13/32 I.D. X 13/16 IN O.D. ZN PL H BOLT SHOULDER UNC J WASHER SAE FLAT 21/32 I.D. X 1 5/16 IN O.D. ZN PL K NUT FLANGE DT SMOOTH FACE UNC L BOLT HH 5/8 NC X 1.75 LG GR5 ZN PL M WASHER FLAT HARDENED 5/8 IN. NOMINAL (L9) N BOLT HH1/2NCX3.0LGGR.5ZNPL P NUT FLANGE LOCK SM FACE DT UNC GR5 Q BOLT HH M12 X 1.75 X 30 LG ZN PL R WASHER FLAT, 17/32 I.D. X 1-1/16 O.D. 87. Includes cross (MD #150886), auto-lok repair kit (MD #133632), yokes (MD #150887, ), guards , ), joints (MD #236831, ), safety signs (MD #30316, 36651), and decal (MD #194521). 88. For markets that require CE compliance. Includes cross (MD #150886), auto-lok repair kit (MD #133632), yoke (MD #150887), guard repair kit (MD #236804), guards (MD #236813, ), joints (MD #236802, ), safety signs (MD #30316, 36651), decal (MD #194521), safety chain, and manual. 89. Includes two safety chains, CE certification decal, CE warning decal, CE manual, and instruction sheet Revision A

84 FRONT HALF DRIVELINES 20 Front Half Drivelines Revision A

85 FRONT HALF DRIVELINES Ref Part Number Description Qty DRIVELINE 1.75 IN 20 T FRONT HALF (FOR 3PT HITCH) DRIVELINE C/W DECALS (NORTH AMERICA) DRIVELINE C/W DECALS & SHIELD CHAIN (EXPORT) YOKE YOKE REPAIR KIT SHIELD, C/W DECAL SHIELD REPAIR KIT CROSS KIT CE CONVERSION (EXPORT ONLY) 92 A/R Serial Number DRIVELINE IN 21 T FRONT HALF (FOR 3PT HITCH) DRIVELINE C/W DECALS (NORTH AMERICA) DRIVELINE C/W DECALS & SHIELD CHAIN (EXPORT) YOKE YOKE REPAIR KIT SHIELD, C/W DECAL SHIELD REPAIR KIT CROSS KIT CE CONVERSION (EXPORT ONLY) 92 A/R 90. Includes decal (MD #194521). 91. For markets that require CE compliance. Includes cross (MD #150886), yoke (MD #150890), yoke repair kit (MD #150891), guard repair kit (MD #236804), outer guard CE (MD #236815), safety sign (MD #30316), decal (MD #194521), safety chain, and manual. 92. Includes two safety chains, CE certification decal, CE warning decal, CE manual, and instruction sheet. 93. For markets that require CE compliance. Includes cross (MD #150886), yoke (MD #150893), yoke repair kit (MD #133632), guard repair kit (MD #236804), outer guard CE (MD #236816), safety sign (MD #30316), decal (MD #194521), safety chain, and manual Revision A

86 FRONT HALF DRIVELINES Revision A

87 FRONT HALF DRIVELINES Ref Part Number Description Qty DRIVELINE 1.75 IN 20 T FRONT HALF (STD DRAWBAR HITCH) DRIVELINE C/W DECALS (NORTH AMERICA) DRIVELINE C/W DECALS & SHIELD CHAIN (EXPORT) YOKE YOKE REPAIR KIT SHIELD, C/W DECAL SHIELD REPAIR KIT CROSS KIT CE CONVERSION (EXPORT ONLY) 96 A/R Serial Number DRIVELINE IN 21 T FRONT HALF (STD DRAWBAR HITCH) DRIVELINE C/W DECALS (NORTH AMERICA) DRIVELINE C/W DECALS & SHIELD CHAIN (EXPORT) YOKE YOKE REPAIR KIT SHIELD, C/W DECAL SHIELD REPAIR KIT CROSS KIT CE CONVERSION (EXPORT ONLY) 96 A/R 94. Includes decal (MD #194521). 95. For markets that require CE compliance. Includes cross (MD #150886), yoke (MD #150890), yoke repair kit (MD #150891), guard repair kit (MD #236804), outer guard CE (MD #236829), safety sign (MD #30316), decal (MD #194521), safety chain, and manual. 96. Includes two safety chains, CE certification decal, CE warning decal, CE manual, and instruction sheet. 97. For markets that require CE compliance. Includes cross (MD #150886), yoke (MD #150893), yoke repair kit (MD #133632), guard repair kit (MD #236804), outer guard CE (MD #236828), safety sign (MD #30316), decal (MD #194521), safety chain, and manual Revision A

88 HITCH HYDRAULICS AND ELECTRICAL 21 Hitch Hydraulics and Electrical Revision A

89 HITCH HYDRAULICS AND ELECTRICAL Ref Part Number Description Qty PIN LYNCH3/16X19/16IN FILTER HEAD 1 5/8 IN., 12 SAE (#20) FILTER ELEMENT 10 MICRON NOMINAL LINE HYDRAULIC LINE HYDRAULIC (14-16 FT) LINE HYDRAULIC (18 FT) LINE HYDRAULIC FITTING CONNECTOR HYD FITTING UNION HYD FITTING CONNECTOR HYD FITTING ADAPTER HYD, C/W O-RING VALVE RELIEF RELIEF CARTRIDGE FOR VALVE (MD #142832) SEAL KIT FOR VALVE (MD #142832) FITTING ADAPTER HYD PLUG HEX, C/W O-RING HOSE FITTING ELBOW, BULKHEAD UNION HYD LINE HYDRAULIC (14-16 FT) LINE HYDRAULIC (18 FT) LINE HYDRAULIC (18 FT) LINE HYDRAULIC (18 FT) FITTING UNION HYD FITTING COUPLING HYD HOSE FITTING ELBOW, BULKHEAD UNION HYD VALVE BALL FITTING CONNECTOR HYD FITTING ELBOW 45 HYD, C/W O-RING LINE HYDRAULIC (14-16 FT) LINE HYDRAULIC (18 FT) LINE HYDRAULIC (18 FT) 2 Serial Number NOTE: For cylinder hydraulics, refer to Section 25 Pull-Type Steering and Lift Cylinder Hydraulics, page Revision A

90 HITCH HYDRAULICS AND ELECTRICAL Revision A

91 HITCH HYDRAULICS AND ELECTRICAL Ref Part Number Description Qty LINE HYDRAULIC (18 FT) FITTING UNION HYD 2 32 REF HOSE HYDRAULIC RELAY TRANSPORT LIGHTING MODULE NUT SPECIAL HARNESS WIRING (14-16 FT) HARNESS WIRING (18 FT) FASTENER CABLE TIE BLACK PLATE PLATE CLAMP Serial Number HITCH PIN WELDMENT HITCH PIN WELDMENT PIN CLEVIS ARM WELDMENT HOSE HYDRAULIC (14-16 FT) HOSE HYDRAULIC (18 FT) HOSE HYDRAULIC (14-16 FT) HOSE HYDRAULIC (18 FT) HOSE HYDRAULIC (14-16 FT) HOSE HYDRAULIC (18 FT) FITTING CONNECTOR HYD, C/W O-RING FITTING CONNECTOR HYD, C/W O-RING A NUT FLANGE LOCK SM FACE DT UNC GR5 B NUT HEX LOCK DT UNC C SCREW MACHINE NOTE: For cylinder hydraulics, refer to Section 25 Pull-Type Steering and Lift Cylinder Hydraulics, page Quantities: ft. = 12, 18 ft. = Pressure to gearbox 100.Return from gearbox 101.Case drain from gearbox 102.To roll drive gearbox motor top port (return) and bottom port (pressure). 103.To roll drive gearbox motor case drain port Revision A

92 HITCH ASSEMBLY 22 Hitch Assembly Revision A

93 HITCH ASSEMBLY Ref 1 Part Number Description Qty HITCH C/W BUSHINGS (14-16 FT) HITCH C/W BUSHINGS (18 FT) BUSHING SLEEVE FITTING LUBE 90 1/4-28 TAPER THD GAUGE LEVEL CAP 1 IN. NPT O-RING FITTING CONNECTOR HYD CAP 3/8 IN. TUBE PLUG MAGNETIC, C/W O-RING O-RING FOR MAGNETIC PLUG (MD #44207) Serial Number 104.Includes two plugs (MD #44207), two bushings (MD #107201), fittings (MD #21010, 21804), O-ring (MD #50222), gauge (MD #156696), and cap (MD #30813) Revision A

94 NON-ARTICULATED PULL-TYPE HITCH HYDRAULICS AND ELECTRICAL 23 Non-Articulated Pull-Type Hitch Hydraulics and Electrical Revision A

95 NON-ARTICULATED PULL-TYPE HITCH HYDRAULICS AND ELECTRICAL Ref Part Number Description Qty HITCH C/W DECALS AND BUSHINGS BUSHING HITCH HEAD FILTER ELEMENT FILTER, 10 MICRON FITTING CONNECTOR HYDRAULIC FITTING ADAPTER HYD, C/W O-RING VALVE HYDRAULIC, RELIEF RELIEF CARTRIDGE FOR VALVE (MD #142832) SEAL KIT FOR VALVE (MD #142832) FITTING ADAPTER HYDRAULIC PLUG HEX, C/W O-RING LINE HYDRAULIC LINE HYDRAULIC FITTING UNION HYDRAULIC INDICATOR OIL LEVEL LINE HYDRAULIC FITTING UNION HYDRAULIC LINE HYDRAULIC FITTING UNION HYDRAULIC LINE HYDRAULIC LINE HYDRAULIC VALVE BALL CLAMP HYDRAULIC LINE PAD RUBBER FITTING CONNECTOR HYDRAULIC 2 24 REF MODULE LIGHT RELAY REF HARNESS WIRING, LIGHTS O-RING LINE HYDRAULIC 2 Serial Number NOTE: For cylinder hydraulics, refer to Section 25 Pull-Type Steering and Lift Cylinder Hydraulics, page Includes fitting (MD #21010), two bushings (MD #107201), decals (MD #142912, 44944, , , 41668), and two reflectors (MD #115146). 106.Refer to Section 35 Electrical Group, page Revision A

96 NON-ARTICULATED PULL-TYPE HITCH HYDRAULICS AND ELECTRICAL Revision A

97 NON-ARTICULATED PULL-TYPE HITCH HYDRAULICS AND ELECTRICAL Ref Part Number Description Qty LINE HYDRAULIC FITTING CONNECTOR HYDRAULIC PLUG HEX 3/4 ORB, C/W O-RING FITTING TEE, SWIVEL RUN, 3/8 TUBE HOSE CASE DRAIN, TEE TO TUBE (485 MM LG) HOSE CASE DRAIN, TUBE TO PUMP (1650 MM LG) FITTING ELBOW, 9/16 O-RING X 3/8 TUBE GUIDE HOSES HOLDER HYDRAULIC HOSES PIN HITCH HOSE HYDRAULIC, SUCTION (1270 MM LG) CLAMP HOSE, GEAR TYPE, HEAVY DUTY HOSE HYDRAULIC (1270 MM LG) 1 41 REF HOSE HYDRAULIC HOSE HYDRAULIC (2000 MM LG) HOSE HYDRAULIC (2000 MM LG) FITTING CONNECTOR HYDRAULIC TAG HYDRAULIC HOSE, HITCH LEFT" TAG HYDRAULIC HOSE, "HITCH RIGHT" TAG HYDRAULIC HOSE, "RAISE HEADER" JACK HITCH CHAIN SAFETY WASHER FLAT, RECTANGULAR HOSE HYDRAULIC, 2720 MM LG (14-16 FT) HOSE HYDRAULIC, 2950 MM LG (18 FT) HOSE HYDRAULIC, 2720 MM LG (14-16 FT) HOSE HYDRAULIC, 2950 MM LG (18 FT) HOSE HYDRAULIC, 2860 MM LG (14-16 FT) HOSE HYDRAULIC, 3090 MM LG (18 FT) Serial Number NOTE: For cylinder hydraulics, refer to Section 25 Pull-Type Steering and Lift Cylinder Hydraulics, page Refer to Section 25 Pull-Type Steering and Lift Cylinder Hydraulics, page Pressure to gearbox 109.Return from gearbox 110.Case drain from gearbox Revision A

98 NON-ARTICULATED PULL-TYPE HITCH HYDRAULICS AND ELECTRICAL Revision A

99 NON-ARTICULATED PULL-TYPE HITCH HYDRAULICS AND ELECTRICAL Ref Part Number Description Qty FITTING ADAPTER HYDRAULIC, C/W O-RING FITTING CONNECTOR HYDRAULIC, C/W O-RING SUPPORT HYDRAULIC HOSES CHANNEL HYDRAULIC HOSE SUPPORT FITTING LUBE, 90, HITCH PIN 1 59 REF PUMP/GEARBOX ASSEMBLY PLATE PUMP ARM TORQUE FITTING ADAPTER HYDRAULIC, C/W O-RING FITTING HYDRAULIC, STRAIGHT, C/W O-RING O-RING FOR FITTING (MD #30910) CHAIN SAFETY PLATE HITCH EXTENSION CLAMP CASTING, HITCH EXTENSION PIN CLEVIS PIN HAIR PIN HITCH, C/W HAIR PIN 1 Serial Number NOTE: For cylinder hydraulics, refer to Section 25 Pull-Type Steering and Lift Cylinder Hydraulics, page To roll drive gearbox motor top port (return) and bottom port (pressure). 112.To roll drive gearbox motor case drain port. 113.Refer to Section 24 Non-Articulated Pull-Type Pump/Gearbox Assembly, page Revision A

100 NON-ARTICULATED PULL-TYPE HITCH HYDRAULICS AND ELECTRICAL Revision A

101 NON-ARTICULATED PULL-TYPE HITCH HYDRAULICS AND ELECTRICAL Ref Part Number Description Qty A NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT B BOLT HEX HEAD, 1/2 NC X 1-3/4 IN., GR. 5 C WASHER LOCK, 1/2 IN. I.D. D NUT HEX, 1/2 NC, GR. 5 E BOLT RHSN,3/8NCX3IN.,GR.5 F NUT SMOOTH FLANGE, 3/8 NC, DT G WASHER FLAT, 16.7 MM I.D. X 70 MM O.D. X 6.4 MM THICK H WASHER LOCK, 5/8 IN. I.D. J BOLT HEX HEAD, 5/8 NC X 2-1/4 IN., GR. 5 K BOLT HEX HEAD, 5/8 NC X 1-3/4 IN., GR. 5 L NUT LOCK, SMOOTH FLANGE, 5/8 NC, DT M BOLT HEX HEAD, 3/4 NC X 2-1/2 IN., GR. 5 N NUT LOCK, HEX, 3/4 NC, DT P BOLT RHSN, 1/2 NC X 2-1/2 IN., GR. 5 Q BOLT RHSN,1/2NCX1IN.,GR.5 R BOLT HEX HEAD, 3/4 NC X 4 IN., GR. 5 S WASHER LOCK, 3/4 IN. I.D. T NUT HEX, 3/4 NC, GR. 5 U BOLT HEX HEAD, 1/2 NC X 1-1/4 IN., GR. 5 V BOLT HEX HEAD, 3/8 NC X 1-1/4 IN., GR. 5 W WASHER FLAT, 13/32 I.D. X 13/16 IN. O.D. X WASHER FLAT, 1-1/16 I.D. X 2 IN. O.D. Serial Number NOTE: For cylinder hydraulics, refer to Section 25 Pull-Type Steering and Lift Cylinder Hydraulics, page Revision A

102 NON-ARTICULATED PULL-TYPE PUMP/GEARBOX ASSEMBLY 24 Non-Articulated Pull-Type Pump/Gearbox Assembly Revision A

103 NON-ARTICULATED PULL-TYPE PUMP/GEARBOX ASSEMBLY Ref 1 2 Part Number Description Qty KIT 540 RPM PUMP KIT 1000 RPM PUMP PISTON PUMP COMPONENTS PUMP PISTON(540RPM) PUMP PISTON (1000 RPM) RING RETAINING, OUTER SEAL SHAFT (WAS 30046) RING RETAINING BEARING RACE THRUST BEARING THRUST BEARING NEEDLE, HOUSING O-RING HOUSING TO BACK PLATE SEALKIT PISTONPUMP 117 CONNECTING COMPONENTS SUN GEAR 540 RPM, PUMP TO GEAR BOX CONNECTION SUN GEAR 1000 RPM, PUMP TO GEAR BOX CONNECTION RING RETAINING, SUN GEAR O-RING PUMP TO GEAR BOX CONNECTION 1 Serial Number NOTE: Check that pump and gearbox are matched as follows: 540 rpm = pump la_, with box ; 1000 rpm = pump la_ with box Model numbers are stamped on the pump mounting flange and the gearbox front plate. 114.Includes pump (MD #36882), sun gear (MD #50099), retaining ring (MD #5924), O-ring (MD #30045), drive-step up box (MD #36883), carrier assy. (MD #36942), bearing (MD #50208), and seal kit (MD #36854). 115.Includes pump (MD #36891), sun gear (MD #50100), retaining ring (MD #5924), O-ring (MD #30045), drive-step up box (MD #36892), carrier assy. (MD #36943), bearing (MD #50208), and seal kit (MD #36854). 116.Includes rings (MD #18900, 30144), seal (MD #50217), bearings (MD #30140, 30141, 21420), O-ring (MD #30045), and seal kit (MD #30247). 117.Includes rings (MD #18900, 30144), seal (MD #50217), and O-ring (MD #30045) Revision A

104 NON-ARTICULATED PULL-TYPE PUMP/GEARBOX ASSEMBLY Revision A

105 NON-ARTICULATED PULL-TYPE PUMP/GEARBOX ASSEMBLY Ref 13 Part Number Description Qty GEARBOX COMPONENTS DRIVE-STEP UP BOX (540 RPM) DRIVE-STEP UP BOX (1000 RPM) NSS RING RETAINING, INTERNAL 3 IN NSS SEAL SHAFT 1 16 NSS O-RING HOUSING TO FRONT PLATE/ADAPTER PLATE 2 17 NSS RING RETAINING, EXTERNAL 2-5/32 IN BEARING CARRIER 1 19 NSS RING RETAINING, INTERNAL 3-9/16 IN NSS RING LOCK CARRIER ASSEMBLY (540 RPM) CARRIER ASSEMBLY (1000 RPM) SEAL KIT GEARBOX 120 Serial Number NOTE: Check that pump and gearbox are matched as follows: 540 rpm = pump la_, with box ; 1000 rpm = pump la_ with box Model numbers are stamped on the pump mounting flange and the gearbox front plate. 118.Includes carrier assy. (MD #36942), bearing (MD #50208), and seal kit (MD #36854). 119.Includes carrier assy. (MD #36943), bearing (MD #50208), and seal kit (MD #36854). 120.Includes not serviced separately items #14 17 and # Revision A

106 PULL-TYPE STEERING AND LIFT CYLINDER HYDRAULICS 25 Pull-Type Steering and Lift Cylinder Hydraulics Revision A

107 PULL-TYPE STEERING AND LIFT CYLINDER HYDRAULICS Ref 1 Part Number Description Qty CYLINDER HYDRAULIC, STEERING SEAL KIT NUT HEX, 1/2 NC, GR BOLT SOCKET HEAD, 1/2 NC X 2 IN., GR CLEVIS CONTROL STROKE FITTING HYDRAULIC, 90º ELBOW FITTING HYDRAULIC, ADAPTER FITTING HYDRAULIC, CONNECTOR VALVE PRESSURE BALANCE FITTING HYDRAULIC, CONNECTOR LINE HYDRAULIC PIN STEERING CYLINDER PIN COTTER, 1/4 X 2 IN CYLINDER SLAVE, LIFT (LH) SEAL KIT FOR CYLINDER (MD #149386) FITTING LUBE, 1/4 NF PIN LIFT CYLINDERS FITTING HYDRAULIC, 90º ELBOW VALVE BALL, CYLINDER STOP FITTING HYDRAULIC, ADAPTER HOSE HYDRAULIC, 4060 MM LG PIN RETAINER, LIFT CYLINDERS HOSE HYDRAULIC, 3890 MM LG HOSE HYDRAULIC, 850 MM LG HOLDER HOSE 6 Serial Number NOTE: For hydraulics not shown here, refer to Section 21 Hitch Hydraulics and Electrical, page 81 or 23 Non-Articulated Pull-Type Hitch Hydraulics and Electrical, page Includes seal kit (MD #142839), two nuts (MD #18591), two bolts (MD #135376), clevis (MD #142605), and stroke control (MD #142654). 122.Includes fitting (MD #18671). 123.Bottom of RH to top of LH lift cylinder. 124.Hitch to top of RH lift cylinder. 125.Hitch to steering cylinder Revision A

108 PULL-TYPE STEERING AND LIFT CYLINDER HYDRAULICS Revision A

109 PULL-TYPE STEERING AND LIFT CYLINDER HYDRAULICS Ref Part Number Description Qty FASTENER CABLE TIE MOULDING HOSE PROTECTOR 1 23 REF LIGHT RED, TAIL REF HARNESS WIRING, TAIL LIGHTS CYLINDER RH, MASTER, LIFT SEAL KIT FOR CYLINDER (MD #171197) Serial Number A BOLT RHSN, 3/8 NC X 1 IN., GR. 5 B NUT SMOOTH FLANGE, 3/8 NC, DT C BOLT RHSN, 3/8 NC X 1-1/2 IN., GR. 5 NOTE: For hydraulics not shown here, refer to Section 21 Hitch Hydraulics and Electrical, page 81 or 23 Non-Articulated Pull-Type Hitch Hydraulics and Electrical, page Refer to Section 35 Electrical Group, page Revision A

110 PULL-TYPE CARRIER FRAME AND FLOAT COMPONENTS 26 Pull-Type Carrier Frame and Float Components Revision A

111 PULL-TYPE CARRIER FRAME AND FLOAT COMPONENTS Ref Part Number Description Qty ARM C/W BUSHINGS (LH) BUSHINGS ARM, STEEL ARM C/W BUSHINGS (RH) PIN LEG ARM C/W BUSHINGS BUSHING RUBBER FITTING LUBE, 1/4 IN.-28 UNF PLATE BOLT RETAINER 4 Serial Number RETAINER PIN PIN LEG SPACER WASHER HARDENED BOLT HEX HEAD, 3/4 NC X 20-1/2 IN., TFL PIVOT SPRING ARM RH ARM LH, C/W DECAL PIN COTTER, 3/16 IN. DIAMETER X 1-1/2 IN ASSEMBLY DOUBLE SPRING ASSEMBLY SINGLE SPRING ARM RH, C/W DECAL LINK C/W DECAL ARM LH CHANNEL LINKAGE PAD RUBBER BAR SPACER ARM STOP ARM LINK STOP FLOAT Includes two fittings (MD #18671), two bushings (MD #25579), and decals (MD #23165, ). 128.Includes fitting (MD #18671), two bushings (MD #30019), and decal (MD #23165). 129.Left-hand assembly. 130.Right-hand assembly. 131.Includes decal (MD #142600) Revision A

112 PULL-TYPE CARRIER FRAME AND FLOAT COMPONENTS Revision A

113 PULL-TYPE CARRIER FRAME AND FLOAT COMPONENTS Ref Part Number Description Qty BUMPER RUBBER LINK C/W BUSHING BUSHING RUBBER BAR LINKAGE PIN CLEVIS JOINT ASSEMBLY PIN CLEVIS SPACER 2 Serial Number A BOLT RHSN, 3/8 NC X 1 IN., GR. 5 B NUT SMOOTH FLANGE, 3/8 NC, DT C NUT HEX, 3/4 NC, GR. 5 D NUT HEX, 3/4 IN., DT E BOLT HEX HEAD, 3/4 NC X 2-1/2 IN., GR. 5 F BOLT RHSN, 5/8 NC X 1-1/2 IN., GR. 5 G NUT SMOOTH FLANGE, 5/8 NC, DT H BOLT RHSN, 1/2 NC X 1-1/2 IN., GR. 5 J NUT SMOOTH FLANGE, 1/2 NC, DT K BOLT RHSN, 3/4 NC X 4-1/2 IN., GR. 5 L WASHER FLAT, 13/16 I.D. X 1-1/2 IN. O.D. M BOLT HEX HEAD, 5/8 NC X 2-1/4 IN., GR. 5 N NUT HEX, 5/8 NC, GR. 5 P WASHER FLAT Q WASHER LOCK, 3/8 IN. I.D. R NUT HEX, 3/8 NC, GR. 5 S BOLT RHSN,5/8NCX2IN.,GR.5 T BOLT RHSN, 5/8 NC X 1-1/2 IN., GR. 5 U BOLT HEX HEAD, 1 NC X 3 IN., GR. 5 V WASHER LOCK, 1 IN. I.D. W BOLT HEX HEAD, 1 NC X 7 IN. X WASHER FLAT, 1-1/16 I.D. X 2 IN. O.D. Y BOLT RHSN, 3/8 NC X 1-1/4 IN., GR. 5 Z NUT HEX, CENTER LOCK, 1 NC AA BOLT HH 5/8 NC X 2.0 LG GR. 5 ZN PL 132.Includes rubber bushing (MD #145480) Revision A

114 PULL-TYPE WHEELS AND TIRES 27 Pull-Type Wheels and Tires Revision A

115 PULL-TYPE WHEELS AND TIRES Ref Part Number Description Qty TIRE 31X NHS, 8 PLY, TERRA-RIB WHEEL 15 X 10 LB, WHITE STEM VALVE BOLT WHEEL, 9/16 IN. NF SPINDLE WHEEL SEAL GREASE BEARING CONE, INNER BEARING CUP, INNER FITTING LUBE BEARING CUP, OUTER HUB C/W CUPS AND LUBE FITTING BEARING CONE, OUTER WASHER FLAT, WHEEL PIN COTTER NUT HEX, SLOTTED, 1 IN. NF CAP DUST 2 Serial Number A BOLT HEX HEAD, 1/2 NC X 3-1/4 IN., GR. 5 B NUT LOCK,1/2IN.,DT 133.Includes seal (MD #140248), bearings (MD #140247, , 30701, 30702), lube fitting (MD #50174), and cap (MD #140250) Revision A

116 CONDITIONER ROLLS 28 Conditioner Rolls Revision A

117 CONDITIONER ROLLS Ref Part Number Description Qty ROLL CONDITIONER, BALANCED BRACKET CONDITIONER ROLL SUPPORT FLANGE BEARING FLANGE BEARING BEARING SPHERICAL, 1-1/2 IN. BORE COVER TOP ASSEMBLY SPRING STUD CONNECTOR CHAIN ROLLER, #60H LINK CHAIN, CONNECTOR, # 60H ARM C/W BUSHINGS BUSHING RUBBER PIVOT ASSY BUSHING FLANGED, 5/8 IN. X 7/8 IN. X 1 IN BEARING BALL, 17 MM O.D. BORE FITTING LUBE,1/4IN.NF ROD SUPPORT SHIM PIVOT DISC CONDITIONER ROLL PLATE CONDITIONER ROLL DEFLECTOR LH (PULL-TYPE HEADER) DEFLECTOR LH (SELF-PROPELLED HEADER) DEFLECTOR RH (PULL-TYPE HEADER) DEFLECTOR RH (SELF-PROPELLED HEADER) PLATE 2 Serial Number 134.Includes shafts (MD #170328, ). 135.Includes extension spring and two spring inserts. 136.If replacing previous design formed spring support bracket (serial number prior to ) with newer stud design (MD #102602), also order bolt (MD #180206) and nut (MD #18592). 137.Includes two rubber bushings (MD #13626). 138.Includes two bushings (MD #143687), two bearings (MD #50185), and fitting (MD #18671) Revision A

118 CONDITIONER ROLLS Revision A

119 CONDITIONER ROLLS Ref Part Number Description Qty PLATE RH PLATE LH SHAFT ROLL (LH) SHAFT ROLL (RH) 2 Serial Number A BOLT HEX HEAD, 1/2 NC X 1-1/4 IN., GR. 5 B WASHER FLAT, 17/32 I.D. X 1-1/16 IN. O.D. C WASHER LOCK, 1/2 IN. I.D. D NUT SMOOTH FLANGE, 1/2 NC, DT, GR. 5 E BOLT HEX HEAD, 1/2 NC X 1 IN., GR. 5 F WASHER FLAT, 21/32 I.D. X 1-5/16 IN. O.D. G NUT HEX, 5/8 NC, GR. 5 H WASHER LOCK, 5/8 IN. I.D. J BOLT HEX HEAD, 5/8 NC X 3-1/4 IN., GR. 5 K BOLT SHOULDER, 5/8 NC X 1-3/8 IN. L NUT HEX, JAM, CENTER LOCK, 5/8 NF M BOLT HEX HEAD, 1/2 NC X 1-3/4 IN. TFL, GR. 5 N BOLT RHSN,1/2NCX1IN.,GR.5 P WASHER HARDENED Q BOLT HEX HEAD, 5/8 NC X 12 IN., GR. 5, HEAVY Revision A

120 ROLL STOP LINKAGES (SP HEADER) 29 Roll Stop Linkages (SP Header) Revision A

121 ROLL STOP LINKAGES (SP HEADER) Ref Part Number Description Qty ROD ADJUSTER, C/WDECAL ADJUSTER ROLL GAP PAD PLASTIC PAD RUBBER PLATE ROLL STOP PIN CLEVIS, 23.8 MM, 30 MM, ZN PL WASHER FLAT, 13/16 IN. I.D PIN COTTER, 3/16 DIA. X 1-1/4 IN. 2 Serial Number A NUT HEX, 3/4 NC B BOLT HEX HEAD, 3/8 NC X 1 3/4 IN., GR. 5 C NUT SMOOTH FLANGE, 3/8 NC, DT D WASHER SAE FLAT, 13/32 I.D. X 1.75 LG GR. 5 ZN PL 139.Includes decal (MD #115287) Revision A

122 LIFT LINKS AND HEADER STAND (SP HEADER) 30 Lift Links and Header Stand (SP Header) Revision A

123 LIFT LINKS AND HEADER STAND (SP HEADER) Ref 1 2 Part Number Description Qty MEMBER BOOT, LH MEMBER BOOT, RH 1 Serial Number MEMBER FOOT, LH MEMBER FOOT, RH PIN CLEVIS, 19 MM DIA. X 180 MM PIN HAIR PAD RUBBER PAD RUBBER WASHER FLAT PLATE CENTER LINK, LH PLATE CENTER LINK, RH BOLT HEX HEAD, 1 NC X 5 IN., GR NUT CENTER LOCK, 1.0 NC WASHER FLAT, 1-1/16 IN. I.D SUPPORT HEADER STAND PIN CLEVIS, 16 MM DIA. X 95 MM PIN LYNCH PIN CLEVIS, 25 MM DIA. X 85 MM 1 A BOLT HEX HEAD, 3/4 NC X 3-1/2 IN., GR. 5 B NUT LOCK, 3/4 NC DT C BOLT HEX HEAD, 3/4 NC X 5 IN., GR. 5 D WASHER FLAT, 13/16 IN. I.D. E NUT SIDE LOCK, 3/4 NC DT F PIN COTTER, 1/4 X 2 IN Revision A

124 CENTER CROP DEFLECTOR (SP HEADER) 31 Center Crop Deflector (SP Header) Revision A

125 CENTER CROP DEFLECTOR (SP HEADER) Ref Part Number Description Qty DEFLECTOR CROP, CENTER BRACKET U, MOUNTING HANDLE ADJUSTMENT HANDLE GRIP VINYL KIT BAFFLE BRACE BRACKET MOUNTING SPRING TORSION DEFLECTOR PANEL (SP HEADER AUGER COVER) HINGE RH (SP HEADER AUGER COVER) HINGE LH (SP HEADER AUGER COVER) SUPPORT HINGE (SP HEADER AUGER COVER) PIN CLEVIS (SP HEADER AUGER COVER) PIN HAIR (SP HEADER AUGER COVER) DEFLECTOR PLASTIC (SP HEADER AUGER COVER) WASHER FLAT (SP HEADER AUGER COVER) 8 Serial Number A BOLT RHSN,3/8NCX3/4IN.,GR.5 B NUT SMOOTH FLANGE, 3/8 NC, DT C BOLT RHSN,3/8NCX3IN.,GR.5 D BOLT HEX HEAD, 5/8 NC X 5 1/2 IN., GR. 5 E WASHER FLAT, 21/32 IN. I.D. F NUT HEX, 5/8 NC G WASHER FLAT 17/32 I.D. X 1 1/16 IN. O.D. H WASHER REG. LOCK 1/2 IN. NOM. ID ZP J BOLT HEX HEAD, 1/2-13 UNC, 1.0 IN. LG, ZN PL, GR 5 K NUT FLANGE LOCK SM FACE DT UNC GR. 5 L BOLT RHSN,1/2NCX1.0GR.5ZNPL M BOLT RHSN, 3/8 NC X 0.75 GR. 5 ZN PL N BOLT RHSN, 5/16 NC X 1.0 GR. 5 ZN PL P NUT SMOOTH FLANGE, 5/16 NC, DT Q WASHER FLAT Revision A

126 PULL-TYPE FORMING SHIELDS 32 Pull-Type Forming Shields Revision A

127 PULL-TYPE FORMING SHIELDS Ref Part Number Description Qty SUPPORT LH, C/W REFLECTIVE DECAL Serial Number SUPPORT RH, C/W REFLECTIVE DECAL SUPPORT RH, C/W REFLECTIVE DECAL SUPPORT CENTER DEFLECTOR REAR PIN CLEVIS PIN HAIR COVER TOP DEFLECTOR SIDE, LH DEFLECTOR SIDE, LH DEFLECTOR SIDE, RH DEFLECTOR SIDE, RH BAR DEFLECTOR ADJUSTER DEFLECTOR INNER, LH DEFLECTOR INNER, RH 1 A BOLT RHSN,3/8NCX3/4IN.,GR.5 B NUT SMOOTH FLANGE, 3/8 NC, DT C BOLT RHSN, 1/2 NC X 1-1/4 IN., GR. 5 D NUT SMOOTH FLANGE, 1/2 NC, DT E BOLT HEX HEAD, 1/2 NC X 1 IN., GR. 5 F WASHER LOCK, 1/2 IN. I.D. G NUT HEX, 3/4 NC, GR. 5 H BOLT HEX HEAD, 5/8 NC X 1-1/4 IN., GR. 5 J NUT SMOOTH FLANGE, 5/8 NC, DT K WASHER FLAT, 21/32 IN. I.D. 140.Includes amber reflector (MD #115146) Revision A

128 SP HEADER FORMING SHIELDS 33 SP Header Forming Shields Revision A

129 SP HEADER FORMING SHIELDS Ref Part Number Description Qty B5225 KIT SELF-PROPELLD WINDROWER FORMING SHIELD 141 Serial Number COVER FORMING SHIELD KIT BRACKET WELDTS CHANNEL BAFFLE REAR ANGLE REAR DEFLECTOR SIDE, LH DEFLECTOR SIDE, RH DEFLECTOR INNER, LH DEFLECTOR INNER, RH ROD ADJUSTER PIN CLEVIS, 1/2 X 2 IN. LG PIN LYNCH STRAP RUBBER HANDLE BAFFLE ADJUSTMENT WASHER FLAT, 13.5 MM I.D., 47 MM O.D., 3 MM THICK WASHER RUBBER BOLT HEXHEAD,5/8NCX7IN.,GR PIN HAIR SPACER TUBE, TRACTOR MOUNTED WASHER FLAT HARDENED PLATE SPACER 2 A NUT SMOOTH FLANGE, 5/8 NC, DT B BOLT RHSN, 5/8 NC X 1-1/4 IN., GR. 5 C NUT SMOOTH FLANGE, 1/2 NC, DT D BOLT HEX HEAD, 1/2 NC X 1 IN., GR. 5 E BOLT RHSN, 1/2 NC X 1-1/2 IN., GR. 5 F BOLT RHSN,3/8NCX3/4IN.,GR.5 G NUT SMOOTH FLANGE, 3/8 NC, DT H WASHER FLAT, 21/32 IN. I.D. 141.Kits available through Whole Goods only. 142.Includes both left-hand and right-hand brackets Revision A

130 SP HEADER FORMING SHIELDS Revision A

131 SP HEADER FORMING SHIELDS Ref Part Number Description Qty J BOLT HEX HEAD, 1/2 NC X 8.0 IN., GR. 5 K PIN COTTER 5/32 X 1-1/2 IN. L NUT HEX JAM, 5/8 NC M WASHER FLAT, 13/16 IN. I.D. N NUT LOCK, 1/2 NC, DT P BOLT HH1/2NCX3.25LGGR.5ZNPL Q BOLT HH 1/2 X 4.0 LG GR. 5 ZN PL R NUT FLANGE LOCK SM FACE DT UNC GR. 5 Serial Number Revision A

132 LEAN BAR, UNPLUG WRENCH, AND SIDE SHOES 34 Lean Bar, Unplug Wrench, and Side Shoes Revision A

133 LEAN BAR, UNPLUG WRENCH, AND SIDE SHOES Ref 1 2 Part Number Description Qty TUBE LEAN BAR (A30-S) 14 FT TUBE LEAN BAR (A30-S) 16 FT TUBE LEAN BAR (A40-D) 14 FT TUBE LEAN BAR (A30-D AND A40-D) 16 FT TUBE LEAN BAR (A30-D AND A40-D) 18 FT COVER LEAN BAR TUBE (A30-D AND A40-D) TUBE KNIFE STORAGE (A40-D) 14 FT TUBE KNIFE STORAGE (A30-D AND A40-D) 16 FT TUBE KNIFE STORAGE (A30-D AND A40-D) 18 FT SHOE SIDE, LH SHOE SIDE, RH WRENCH UNPLUG (A30-S AND A40-D) PIN HAIR (A30-S AND A40-D) HOLDER WRENCH, SPRING-ACTION (A40-D ONLY) WRENCH UNPLUG (A30-D) 1 Serial Number A BOLT RHSN, 1/2 NC X 1 IN., GR. 5 B NUT SERRATED FLANGE, 1/2 NC, DT C BOLT RHSN,1/2NCX1IN.,GR.5 D NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT E BOLT HEX FLANGE HEAD, 3/8 NC X 5/8 IN., GR. 5 F BOLT RHSN,1/4NCX3/4IN.,GR.5 G NUT LOCK, 1/4 NC DT H BOLT HEX HEAD 1/2 NC X 1-1/4 IN., GR 5. J NUT HEX 1/2 NC Revision A

134 ELECTRICAL GROUP 35 Electrical Group Revision A

135 ELECTRICAL GROUP Ref Part Number Description Qty SP AND PT HEADERS (ITEMS #1-3) SUPPORT LIGHT, HEADER LIGHT AMBER 2 NSS REPLACEMENT BULB #1156, SEE RETAILER LENS AMBER, REPLACEMENT CLIP PLASTIC SP AND PT 2 4 SP HEADERS ONLY(ITEMS#4-7) KIT WIRING HARNESS, C/W INSTRUCTION AND TOOL PANEL NUT DEUTSCH CONNECTOR WASHER, LOCK SPRING DEUTSCH CONNECTOR CAP, RECEPTACLE C/W CHAIN DEUTSCH CONNECTOR SUPPORT HARNESS / COUPLER CLIP PLASTIC, A30-D SP HEADER ONLY CHANNEL C/W REFLECTORS PT HEADERS ONLY (ITEMS #8-12) HARNESS WIRING, LIGHTS, PT HEADER FRAME SECTION MODULE LIGHT RELAY, PULL-TYPE HITCH HARNESS MODULE TO FRONT OF PULL-TYPE HITCH Serial Number LIGHT TAIL, RED, PULL-TYPE CARRIER FRAME LIGHT TAIL, RED, PULL-TYPE CARRIER FRAME NSS REPLACEMENT BULB #1157, SEE RETAILER LENS RED, REPLACEMENT LENS BLACK, REPLACEMENT HARNESS TAIL LIGHT, PT CARRIER FRAME SECTION HARNESS TAIL LIGHT, PT CARRIER FRAME SECTION NOTE: For specific electrical harness parts, refer to Electrical Connector Parts Catalog (MD #169641). 143.Includes contact removal tool (MD #134013). 144.Includes reflectors (MD #115146, ) Revision A

136 ELECTRICAL GROUP Revision A

137 ELECTRICAL GROUP Ref Part Number Description Qty A BOLT HEX HEAD, 1/2 NC X 2 1/4 IN., GR. 5 B WASHER FLAT, 17/32 I.D. X 1-1/16 IN. O.D. C NUT LOCK, SMOOTH FLANGE, 1/2 NC, DT D SCREW TRUSSHEAD,#8X3/4IN. E NUT KEPS LOCK, #8 F BOLT RHSN, #10 NC X 1/2 IN. G NUT HEX LOCK, #10 NC H BOLT RHSN, 1/4 NC X 1-3/4 IN. J NUT LOCK, SMOOTH FLANGE, 3/8 NC, DT (SPACER) K NUT LOCK, 1/4 NC DT Serial Number NOTE: For specific electrical harness parts, refer to Electrical Connector Parts Catalog (MD #169641) Revision A

138 DECALS AND REFLECTORS 36 Decals and Reflectors Revision A

139 DECALS AND REFLECTORS Ref Part Number Description Qty DECAL 25HOURLUBE DECAL 50HOURLUBE DECAL 540 RPM DECAL 1000 RPM DECAL WARNING DECAL CAUTION DECAL PATENT NUMBER DECAL WARNING DECAL DANGER, GUARD MISSING, DO NOT OPERATE DECAL DRIVELINE GREASE, 50 HOUR DECAL WARNING DECAL ROLL GAP, PULL-TYPE HEADER DECAL ROLL GAP, SP HEADER DECAL CAUTION, GENERAL DECAL DANGER, LOCKOUT VALVES DECAL DANGER DECAL WARNING DECAL 540 RPM PTO DECAL 1000 RPM PTO DECAL IMPORTANT, SPECIAL GUARDS DECAL WARNING, HITCH SWING LOCK DECAL PUMP STORAGE DECAL DANGER, SHIELD MISSING DECAL NO LIFT OR TIE DECAL DANGER, ROTATING DRIVELINE DECAL IMPORTANT, WHEEL BOLT TORQUE DECAL WARNING DECAL HYDRAULIC OIL DECAL SMV REFLECTOR DAY-GLOW ORANGE REFLECTOR AMBER REFLECTOR RED STRIP ANTI SLIP (180 X 50 MM) Serial Number Revision A

140 TWO-PANEL (NON-TEXT) DECALS 37 Two-Panel (Non-Text) Decals Revision A

141 TWO-PANEL (NON-TEXT) DECALS Ref Part Number Description Qty DECAL KEEPSHIELDS IN PLACE DECAL GENERAL HAZARD DECAL SHUT DOWN FOR SERVICE, TWO-PANEL DECAL INSTALL LOCK, TWO-PANEL DECAL PINCH POINT EU DECAL HEADER CRUSHING HAZARD DECAL CEDRIVELINE DECAL HIGH PRESSURE FLUID (VERTICAL FORMAT) DECAL HIGH PRESSURE FLUID (HORIZONTAL FORMAT) DECAL STAND CLEAR DECAL HOT FLUID UNDER PRESSURE DECAL LOCK PT HYD FOR TRANSPORT DECAL WARNING MOVING PARTS DECAL READ MANUAL Serial Number Revision A

142 PRODUCT IDENTIFICATION DECALS AND PAINT 38 Product Identification Decals and Paint Revision A