Parts Manual for 21" STEEL DECK WALK BEHIND MOWERS SERIES 18 MODELS

Size: px

Start display at page:

Download "Parts Manual for 21" STEEL DECK WALK BEHIND MOWERS SERIES 18 MODELS"

Tabitha Young
5 years ago
Views:

Parts Manual for 21" STEEL DECK WALK BEHIND MOWERS SERIES 18 PUSH MODELS 216518B PROPELLED MODELS EP217018BV ERP217018BV P216018KWV P216518B P217018BV P217018BVE

1 Parts Manual for 21" STEEL DECK WALK BEHIND MOWERS SERIES 18 PUSH MODELS B PROPELLED MODELS EP217018BV ERP217018BV P216018KWV P216518B P217018BV P217018BVE RP216018KWV RP217018BV RP217018BVE McDonough, GA, U.S.A. COPYRIGHT 2005 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision 1, 9/9/2005 Manual No

3 Table Of Contents PAGE GROUP 4 HANDLES & CONTROLS 8 CUTTING DECK, BLADES 12 FRONT WHEEL BRACKET 14 REAR WHEEL BRACKETS, LATCHES 16 FRONT WHEELS 18 REAR WHEELS 20 DRIVE SYSTEM SELF-PROPELLED 24 TRANSMISSION (DIFFERENTIAL) 26 THROTTLE CONTROLS/ENGINE SPECS 28 SIDE CHUTE ADAPTER 30 ACCESSORY GRASS BAG 32 ELECTRIC START COMPONENTS 34 DECALS 36 SNAPPERIZER ACCESSORY 38 THATCHERIZER ASSEMBLY 40 RECYCLING KITS ACCESSORY 21" STEEL DECK SERIES 18 3 Manual No

4 HANDLES & CONTROLS Manual No " STEEL DECK 4 SERIES 18

5 HANDLES & CONTROLS Item Part No Qty Description Note HANDLE, Upper All HANDLE, Middle All HANDLE, Lower LH (Adjustable) All HANDLE, Lower RH (Adjustable) All BAIL, OPC Control All CLIP, Zone Control All *CABLE, Zone Control (52-63/64 Long) CABLE, Zone Control (50-31/64 Long) P217018BVE & RP217018BVE CABLE, Zone Control (56-5/16 Long) P216018KWV & RP216018KWV HANDLE, Clutch Self-Propelled Models GRIP, International Symbol Self-Propelled Models CABLE, Clutch Control (41-1/4 Long) Self-Propelled Models COVER, Vinyl Self-Propelled Models SPRING, Clutch- 21S Self-Propelled Models BRACKET, Shift All TIE, Wire, 1.29 long, black Self-Propelled Models BRACKET, Bell Crank Self-Propelled Models SPACER,.33 x.63 x.156 Self-Propelled Models BELL CRANK Self-Propelled Models CONTROL PANEL (w/o Ground Drive Slot) B **CONTROL PANEL (w/o Electrical Switch Hole) CONTROL PANEL (w/electrical Switch Hole) P217018BVE & RP217018BVE SCREW, 1/4-20 x 1/2 Pan Head Self-Tap (Torx) All WASHER,.33 x.88 x.09 Flat Self-Propelled Models SCREW, 5/16-18 x 7/8 Hex Head Cap, GR 5 Self-Propelled Models TEENUT, 5/16-18 Self-Propelled Models BUSHING, Differential,.328 x.625 x.41 Self-Propelled Models BOLT, 5/16-18 x 3/4 Hex Flange Lock GR 5 All NUT, 5/16-18 Hex Flange Lock, GR 5 was (All) NUT, 5/16-18 Hex Center Lock was (S-P Models) LEVER, Shift Self-Propelled Models NUT, 5/16-24 Hex Center Lock GR 5 was (All) CLIP, Wiring Harness All SCREW, 5/16-18 x 1-7/8 Curved Head GR 2 was (All) KNOB, 5/16-18 Wing (Black) All SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR 5 All WASHER, 1/4 Internal Tooth Lock was (All) Footnotes: Note* used on B, P216518B, P217018BV, RP217018BV, EP217018BV & ERP217018BV Note** used on P217018BV, P216518B, P216018KWV, RP217018BV, RP216018KWV, EP217018BV & ERP217018BV Note* See also Throttle Control Page ref Decal Page 21" STEEL DECK SERIES 18 5 Manual No

6 HANDLES & CONTROLS Manual No " STEEL DECK 6 SERIES 18

7 HANDLES & CONTROLS Item Part No Qty Description Note NUT, 1/4-20 Hex was (All) SCREW, 1/4-20 x 2 Hex Head Cap, GR BUSHING,.27 x.35 x.4 Flange Self-Propelled Models PIN, 1/4 x 1-1/2 Self-Propelled Models PUSH-NUT, 1/4 Self-Propelled Models BALL JOINT, 1/4-28 Self-Propelled Models NUT, 1/4-28 Hex Self-Propelled Models FOAM GRIP, 15 long All SCREW, 3/8-16 x 2 Hex Head Cap, GR 5 Self-Propelled Models SCREW, 3/8-16 x 1-3/4 Hex Head Cap, GR 5 Push Models NUT, 3/8-16 Hex Center Lock All WASHER, 5/16 Internal Tooth Lock All WASHER, 7/16 Flat Self-Propelled Models WASHER, Nylon Self-Propelled Models ROD, Speed Control (1/4-28 thread) Self-Propelled Models GUIDE, Rope (1/4-20 thread) All NUT, 1/4-28 Hex GR 5 or B All CABLE-TIE, 7 Self-Propelled Models *THROTTLE CONTROL,.48 x.61 Briggs models *THROTTLE CONTROL, 6.0 KWV Kawasaki models THROTTLE KNOB All KNOB, Shift Self-Propelled Models CLAMP, 7/8 Double Cable Self-Propelled Models SCREW, #8-32 x 1/2 Cross Recess Filister Head Machine Self-Propelled Models NUT, #8-32 Hex Self-Propelled Models BELT GUIDE, Lower Self-Propelled Models WASHER, Belleville Self-Propelled Models WASHER, 1/4 Internal Tooth Lock Self-Propelled Models WASHER, 3/8 Flat Self-Propelled Models COTTER PIN, 5/16 Self Lock Self-Propelled Models DECAL, Easy Walk All CLAMP, Casing models with Briggs Engine SCREW,#10-32 x 5/8 Self-Tap models with Briggs Engine SCREW, 5/16-24 x 1 Hex Head Cap GR 5 All Footnotes: Note* used on B, P216518B, P217018BV, RP217018BV, EP217018BV & ERP217018BV Note** used on P217018BV, P216518B, P216018KWV, RP217018BV, RP216018KWV, EP217018BV & ERP217018BV Note* See also Throttle Control Page ref Decal Page 21" STEEL DECK SERIES 18 7 Manual No

8 CUTTING DECK, BLADES Manual No " STEEL DECK 8 SERIES 18

9 CUTTING DECK, BLADES Item Part No Qty Description Note DECK, Mower (incl. painted HV Deck with Decals) Non-Recycler models DECK, Mower, 21 Hi-Vac (HV) B DECK, Mower (Includes painted Euro M Deck with No Decals) RP217018BVE * DECK, Mower, 21 Non-Adj Air (was or ) Recycler models NUT, 5/16-18 Hex Flange Lock, GR 5 was BOLT, 5/16-18 x 1/2, Short Neck Carriage, GR BOLT, 5/16-18 x 1-1/8 Short Neck Carriage, GR SCREW, 3/8-16 x 1 Self-Tapping engine mount bolts PLUG, Hole, Polyethylene SCREW, 5/16-18 x 1/2 Hex Head Cap, GR BOLT, 5/16-18 x 2-1/4, Hex Flange Lock BUSHING,.388 x.625 x COVER, Belt European models WASHER, 7/16 Flat SCREW, 3/8-24 x 2 Hex Head Cap, GR WASHER, Cone 14A BLADE, Cutter, 21 Air Lift (European) EP217018BV 14B BLADE, Cutter (Standard Lift) Domestic Push & S.P.models 14C BLADE, 21 Ninja (Quad Edge) Recycler models HUB, Blade Drive 25mm I.D KEY, Woodruff #HP-506 Hi-Pro SET SCREW, 5/16-18 x 5/16 Hex Socket PULLEY, Engine (25mm I. D. x 2-1/8 O.D.) SCREW, 1/4-20 x 1/2 Hex Flange Self-Tap (was 90539) EP217018BV & ERP217018BV WELDMENT, Fender European models BOLT, 5/16-18 x 3/4 Short Neck Carriage GR 5 was RETAINER, 5/16 Bolt NUT, 5/16-18 Hex Flange Lock, GR 5 was KIT, Air Lift (Incl. items 24 thru 27) AIR LIFT WASHER, 5/16 Internal Tooth Lock NUT, 5/16-24 Hex, GR 5 was SCREW, 5/16-24 x 21/32 Machine SPACER,.06 Thick for blade hub COVER, Belt PLUG, 5/16 Square Hole Push Models PLUG, 5/16 Round Hole qty. 3 on Push Models Footnotes: Note* Same deck as except w/o battery bracket holes. Note* Purchase engine parts from engine manufacturer dealer. 21" STEEL DECK SERIES 18 9 Manual No

10 CUTTING DECK, BLADES Manual No " STEEL DECK 10 SERIES 18

11 CUTTING DECK, BLADES Item Part No Qty Description Note DECAL, Caution, International Symbols European models NUT, 5/16-18 Hex Large Flange Center Lock *ENGINE, 6.0 Kawasaki, Model FJ180V-AS13-R P216018KWV & RP216018KWV *ENGINE, 6.5 Briggs Intek, Model 123K E B & P216518B *ENGINE, 7.0 Briggs Intek E/S, Model E1 P217018BVE & RP217018BVE *ENGINE, 7.0 Briggs Intek, Model E1 EP217018BV & ERP217018BV *ENGINE, 7.0 Briggs Intek, Model E1 P217018BV & RP217018BV Footnotes: Note* Same deck as except w/o battery bracket holes. Note* Purchase engine parts from engine manufacturer dealer. 21" STEEL DECK SERIES Manual No

12 FRONT WHEEL BRACKET Manual No " STEEL DECK 12 SERIES 18

13 FRONT WHEEL BRACKET Item Part No Qty Description Note ASSEMBLY, Left Wheel Arm (Incl. items 2, 3, 4, 5B & 6) ASSEMBLY, Right Wheel Arm (Incl. items 2, 3, 4, 5A & 6) BOLT, 5/16-18 Hex washer Face Shoulder per wheel arm assembly LATCH, Height per wheel arm assembly GRIP, Height Latch per wheel arm assembly 5A WHEEL ARM, R.H. Front (Round Hole) 5B WHEEL ARM, L.H. Front (Square Hole) not shown RETAINER, 5/16 Bolt NUT, 5/16-18 Hex Flange Lock, GR 5 was WELDMENT, Front Wheel Bracket was or (all) AXLE, 21 Footnotes: 21" STEEL DECK SERIES Manual No

14 REAR WHEEL BRACKETS, LATCHES Manual No " STEEL DECK 14 SERIES 18

15 REAR WHEEL BRACKETS, LATCHES Item Part No Qty Description Note BEARING, 9/16 I.D. per Rear Wheel Arm SCREW, #10-32 x 3/8 Hex washer Self-Tap per Rear Wheel Arm LATCH, Height Adjusting (long) per Rear Wheel Arm NUT, 1/4-20 Hex was or NUT, 5/16-18 Hex Flange Lock, GR 5 was ASSY, Wheel Arm, Right Rear (Round hole) (Push) (Incl. items 3, 10, 14, 15 & 16) ASSY, Wheel Arm, Left Rear (Square hole) (Push) (Incl. items 3, 11, 14, 15 & 16) ASSY, Wheel Arm, Right Rear (S.P.) Incl. 1,2,3,12,14,15 & ASSY, Wheel Arm, Left Rear (S.P.) Incl. 1,2,3,13,14,15 & WHEEL ARM, R.H. Rear (round opening) used on Push models WHEEL ARM, L.H. Rear (square opening) used on Push models ARM, Wheel, Right Rear used on Self-Propelled models ARM, Wheel, Left Rear used on Self-Propelled models BOLT, 5/16-18 x 1 Shoulder per wheel arm assembly RETAINER, 5/16 Bolt per wheel arm assembly GRIP, Height Latch per wheel arm assembly BRACKET, Right Rear Wheel all BRACKET, Left Rear Wheel all AXLE, 21 qty. 2 on push ; 1 on s-p FOOT GUARD, Long, Rear Push Models only FOOT GUARD, Rear Domestic Self Propelled FOOT GUARD, Rear Euro Self-Propelled RING, Split (Black) used on Self-Propelled models SUPPORT, Foot Guard used on Self-Propelled models BOLT, 1/4-20 x 1/2 Short Neck Carriage GR 5 was (Self-Propelled) WASHER, 1/4 Internal Tooth Lock was BOLT, 5/16-18 x 1/2, Short Neck Carriage, GR 5 Footnotes: 21" STEEL DECK SERIES Manual No

16 FRONT WHEELS Manual No " STEEL DECK 16 SERIES 18

17 FRONT WHEELS Item Part No Qty Description Note WHEEL, 8 x 1.75 Plastic all NUT, 7/16-20 Hex Center Lock Jam BUSHING, Axle WASHER, 7/16 Flat PLUG, Wheel all Footnotes: 21" STEEL DECK SERIES Manual No

18 REAR WHEELS Manual No " STEEL DECK 18 SERIES 18

19 REAR WHEELS Item Part No Qty Description Note WHEEL, 10 x 1.75 Plastic Push Models only WHEEL, 10 x 1.75 Plastic used on Self-Propelled models NUT, 7/16-20 Hex Center Lock Jam all BUSHING, Axle Push Models only WASHER, 7/16 Flat PLUG, Wheel all Footnotes: 21" STEEL DECK SERIES Manual No

20 DRIVE SYSTEM SELF-PROPELLED Manual No " STEEL DECK 20 SERIES 18

21 DRIVE SYSTEM SELF-PROPELLED Item Part No Qty Description Note BELT, Poly-V LINK, Differential ASSEMBLY, Clutch Idler (Includes items 3 thru 7) ARM, Clutch Idler PULLEY, Idler SCREW, 1/4-28 x 1-3/8 Hex Head Cap, GR NUT, 1/4-28 Hex Top Lock BUSHING, 3/8 I.D. Nylon SHAFT, Hex Drive PULLEY, Poly-V (2 O.D.) for non-commercial models WASHER, 3/8 Flat SPRING, Idler- Torsion STUD, Idler (3/8-24 thread) HOLDER, Bearing (Inner Half) BALL BEARING, Spherical O.D.,.38 I.D O-RING NUT, 3/8-24 Hex Center Lock, GR HOLDER, Bearing (Outer Half) WASHER,.28 x.63 x.06 Flat COTTER PIN,.06 x.50 was BELT, Engine Drive (Stretch) THRUST PLATE, Short RETAINING RING,.625 External BALL BEARING- 3/4 Bore GUIDE, Thrust Plate (3/8-24 thread) SHIELD, Hex Shaft European models only BALL JOINT, 1/4-28 (not shown) see Handles & Controls page (39) NUT, 1/4-28 Hex (not shown) see Handles & Controls page (40) LINK, Transfer (1/4-28 thread) WASHER, 3/4 Shim WASHER, 3/8 Internal Tooth Lock WASHER, 3/8 Flat NUT, 3/8-24 Hex SPRING, Clutch- 21S NUT, 5/16-18 Hex Flange Lock, GR 5 was BOLT, 5/16-18 x 1/2, Short Neck Carriage, GR SCREW, 1/4-20 x 1/2 Hex Flange Self-Tap was Footnotes: Note* Includes Steel Drive Disc Assy ( ), Bushing ( ), 3/8-16 Hex Nut ( ) & item " STEEL DECK SERIES Manual No

22 DRIVE SYSTEM SELF-PROPELLED Manual No " STEEL DECK 22 SERIES 18

23 DRIVE SYSTEM SELF-PROPELLED Item Part No Qty Description Note COTTER PIN, 3/32 x 1/2 was BUSHING, Powdered Metal DISC, Driven (Cantilever) WASHER, 44 x.78 x.025 Curved RETAINER, 3/8 Bolt SPRING, Wheel Drive BOLT, 5/16-18 x 5/8 Short Neck Carriage GR 5 was ASSEMBLY, Deck Bracket (Incl. items 7 & 44A) RP216018KWV & RP217018BV ASSEMBLY, Deck Bracket (Incl. items 44B, 45 & 46) all S. P. models except for 2 shown above 44A BRACKET, Deck, V21 44B BRACKET, Deck, P21S BUSHING, Flange,.381 x.625 x SPACER,.500 x.65 x SCREW, 5/16-18 x 1/2 Hex Head Cap, GR WASHER, 5/16 Internal Tooth Lock *KIT, Drive Disc Assembly Footnotes: Note* Includes Steel Drive Disc Assy ( ), Bushing ( ), 3/8-16 Hex Nut ( ) & item " STEEL DECK SERIES Manual No

24 TRANSMISSION (DIFFERENTIAL) Manual No " STEEL DECK 24 SERIES 18

25 TRANSMISSION (DIFFERENTIAL) Item Part No Qty Description Note ASSEMBLY, Transmission (Incl. items 1 thru 30) Self-Propelled Models NUT, 5/16-18 Hex Lock was WASHER, Cone PULLEY, Poly-V Belt (3.5 O.D.) WASHER, 44 x.78 x.025 Curved ASSEMBLY, Right Housing (Incl. items 6, 7, 8, 9, 10 & 30) HOUSING, Right Side SCREW, 5/16-24 x 1-1/8 Rib Neck, GR SEAL, 5/8 Internal Diameter BEARING, Tapered- (Differential Housing) BALL BEARING, 7/16 I.D., 1/1/8 O.D. was PLUG, Transmission Housing GEAR, Input AXLE, Short GEAR, Differential (46 Tooth) PLATE, 46T Gear WASHER, Thrust, 3/4 I.D SCREW, #10-32 x 1-1/2 Hex Head Cap GR GASKET, Housing WASHER, 5/16 Internal/External Tooth Lock BRACKET, Differential SCREW, 1/4-20 x 1 Hex washer Self-Tap was SPACER, Axle Gear ASSEMBLY, Long Axle GEAR, Pinion (12 tooth) SPACER, Pinion Gear SHAFT, Pinion NUT, #10-32 Hex Nyloc ASSY, Left Housing (Phantom) HOUSING, Left GASKET, 5/8 O. D oz. 00 Grease not shown Footnotes: NOTE: Transmission Assemblies & (Euro) are available & include Foot Guards. NOTE: Maximum capacity of transmission case is 4 oz. DO NOT OVERFILL! 21" STEEL DECK SERIES Manual No

26 THROTTLE CONTROLS/ENGINE SPECS Manual No " STEEL DECK 26 SERIES 18

27 THROTTLE CONTROLS/ENGINE SPECS Item Part No Qty Description Note THROTTLE CONTROL,.48 x.61 Briggs models THROTTLE CONTROL, 6.0 KWV Kawasaki models Footnotes: conduit length: 48-1/2 conduit length: 53-1/4 21" STEEL DECK SERIES Manual No

28 SIDE CHUTE ADAPTER Manual No " STEEL DECK 28 SERIES 18

29 SIDE CHUTE ADAPTER Item Part No Qty Description Note ASSY, Bag Adapter & Cover (Euro only) (Incl items 2 thru 9) ADAPTER, Grass Bag COVER, Bag Adapter HINGE, Chute Cover BOLT, 1/4-20 x 1/2 Short Neck Carriage, GR WASHER, 1/4 Internal Tooth Lock was NUT, 1/4-20 Hex was STOP, Cover MOULDING, Trim 10A ADAPTER, Grass Bag 10B ASSY, Grass Bag Adapter see Grass Bag Accessory page SPACER,.316 I.D. x.375 O.D. x.310 thick NUT, 5/16-18 Hex Large Flange Center Lock RETAINER, 5/16 Bolt BOLT, 5/16-18 x 3/4 Short Neck Carriage GR 5 was CHUTE, 21 Side P216018KWV WASHER, 5/16 Flat was WING-NUT, 5/16-18 Nyloc COVER, 21 Deck Recycler models NUT, 5/16-18 Hex Large Flange Center Lock Footnotes: Note: For Grass Catcher components see Grass Bag Accessory page. 21" STEEL DECK SERIES Manual No

30 ACCESSORY GRASS BAG Manual No " STEEL DECK 30 SERIES 18

31 ACCESSORY GRASS BAG Item Part No Qty Description Note KIT, Grass Bag Catcher was (Incl. items 2 thru 5) ASSEMBLY, Grass Bag was (Incl. items 2 thru 4) GRASS BAG (Door w/gray Letters) all ASSEMBLY, Bag Wire (12 Wide) all CONNECTOR, Grass Bag (weldment) all ADAPTER, Grass Bag used on Euro S. P ASSEMBLY, Grass Bag Adapter Includes items 7 thru ADAPTER, Grass Bag used on Domestic S. P BRACKET, Rope Guide SCREW, 5/16-18 x 1-1/4 Pan Head Machine BUSHING, Flange,.381 x.625 x PULLEY, Nylon NUT, 5/16-18 Hex Flange Lock, GR 5 was WASHER, 15/32 Flat RIVET, 3/16 x *PLUG, Chute Adapter BRACE, Bag Adapter P216018KWV & RP216018KWV SCREW, M6 x 1.0 x 30MM Hex Head Cap P216018KWV & RP216018KWV SLEEVE,.237/.242 ID x.3135/.3185 x.748 (not shown) Kawasaki models only Footnotes: NOTE: Bag Assembly is composed of items 2, 3 and 4. Note* Used on P216018KWV, P217018BV, P217018BVE & EP217018BV 21" STEEL DECK SERIES Manual No

32 ELECTRIC START COMPONENTS Manual No " STEEL DECK 32 SERIES 18

33 ELECTRIC START COMPONENTS Item Part No Qty Description Note *KIT, Battery 12V P217018BVE & RP217018BVE BATTERY, 12 Volt, 35 CCA was HARNESS, Battery SCREW, #10-24 x 1/2 Pan Head Machine NUT, #10-24 Square **SWITCH ASSEMBLY (Incl. items 6 thru 11) KEY (Set of Two) BEZEL (Seal & Face Nut) COVER, Switch NUT, 5/8-32 Hex Lock SWITCH, Ignition (spring loaded ON/OFF 2 prong) SPACER WIRING HARNESS, B&S WBM similar to BRACKET, Battery COVER, Battery BOLT, 5/16-18 x 1/2 Short Neck Carriage GR NUT, 5/16-18 Hex Flange Lock, GR 5 was CLIP, Wiring CHARGER, Battery (120 Volt; 60 Hertz) CHARGER, Battery (230 Volt; 50 Hertz) BOLT, 5/16-18 x 5/8 Short Neck Carriage GR 5 was RETAINER, 5/16 Bolt Footnotes: Note* For battery and charger kit order Note** Not available as a part sale item, order individual parts. 21" STEEL DECK SERIES Manual No

34 DECALS Manual No " STEEL DECK 34 SERIES 18

35 DECALS Item Part No Qty Description Note DECAL, Easy Walk DECAL, Throttle Control, KWV DECAL, Throttle Control, B&S DECAL, Speed Shift DECAL, Chute/Deflector DECAL, Ignition Switch DECAL, Danger, Cut Finger DECAL, Hi Vac DECAL, Ninja DECAL, Snapper DECAL, Warning (Deck) DECAL, 2004 Year of Mfg DECAL,Euro Community (CE) DECAL, Spart Plug International Symbol DECAL, Caution, Symbols DECAL, Noise (European) DECAL, Warning (Euro) DECAL, OPEI Walk/Ride DECAL, Warning DECAL, Deck/Chute International Warning DECAL, OPC Bail (International Symbol) DECAL, Patent Numbers not shown Footnotes: 21" STEEL DECK SERIES Manual No

36 SNAPPERIZER ACCESSORY Manual No " STEEL DECK 36 SERIES 18

37 SNAPPERIZER ACCESSORY Item Part No Qty Description Note KIT, Snapperizer (Incl. items 1 & 2 thru 5) (for Hi-Vac Rolled Under Lip type decks) KIT, Snapperizer (Incl. items 1& 2A thru 5) (for FR type decks) SCREEN, Fastener Assembly RING, Bottom (21.77 Inside Diameter) 2A RING, Bottom (22.60 Inside Diameter) NUT, 5/16-24 Hex, GR 5 was (only 1 shown) WASHER, 5/16 Split Lock only 1 shown SPRING only 1 shown Footnotes: 21" STEEL DECK SERIES Manual No

38 THATCHERIZER ASSEMBLY Manual No " STEEL DECK 38 SERIES 18

39 THATCHERIZER ASSEMBLY Item Part No Qty Description Note KIT, Thatcherizer (Incl. items 1 thru 27) LATCH, Frame Attachment 2A BAR, Mount (Right Hand) 2B BAR, Mount (Left Hand) ROD, Tine SUPPORT, Wheel TRAY, Tine KIT, Tine Thatching Spring was BUSHING, Wheel Adjuster AXLE, Wheel WHEEL, 7.00 x 1.50 Gage NUT, 1/4-20 Hex Top Lock was (only 9 shown) WASHER, 1/4 Flat was SPRING, Compression BOLT, 1/4-20 x 1-1/4 Hex, GR NUT, 1/4-20 Hex, GR 5 was CAP, Vinyl BOLT, 1/4-20 x 2-1/2 Square Neck Carriage only 1 shown BOLT, 5/16-18 x 1 Square Neck Carriage, GR 5 was (only 1 shown) BOLT, 1/4-20 x 3/4 Square Neck Carriage, GR 5 was WASHER, Reinforcing only 1 shown WASHER, 5/16 Split Lock only 1 shown NUT, 5/16-18 Hex, GR 5 was (only 1 shown) NUT, 1/2 Push BEARING, Nyliner SCREW, 5/16-18 x 1/4 Set WASHER, 1/2 Flat DECAL, Adjustment DECAL, Thatcherizer Footnotes: 21" STEEL DECK SERIES Manual No

40 RECYCLING KITS ACCESSORY Manual No " STEEL DECK 40 SERIES 18

41 RECYCLING KITS ACCESSORY Item Part No Qty Description Note KIT, Recycling Cover (Includes the 2 items below) for 4HP & above engines KIT, Recycling Plug (Incl. items 1 & 2 below) for 4HP & above engines COVER, 21 Deck PLUG, Chute Adapter BLADE, 21 Quad Edge Ninja Footnotes: 21" STEEL DECK SERIES Manual No

Parts Manual for 21" STEEL DECK WALK BEHIND MOWERS SERIES 18 IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO.

44 Parts Manual for 21" STEEL DECK WALK BEHIND MOWERS SERIES 18 IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY. McDonough, GA, U.S.A. COPYRIGHT 2005 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision 1, 9/9/2005 Manual No

21" STEEL DECK WALK BEHIND MOWERS SERIES 19

21 STEEL DECK WALK BEHIND MOWERS SERIES 19 Parts Manual for SERIES 19 MODEL 2167519B (7800031) 2167519B (7800174) 2167519B (7800217) N2167519B (7800133) NP2167519B (7800134) NP2187519BV (7800131) P216019KWV (7800034) P216019KWV (7800193) P2167519B