Information mm. 81 mm

Transcription

1 Compatible Communication Protocol eviceet POFIUS P Each -output/-output type available in the series Each negative common (PP) / positive common (P) type available in the series uilt-in terminator switch for communication (Only for units compatible with POFIUS P with M connector specification) Enclosure IP67 (IP0: For -sub connector specification units, or when connected with S0700 manifold) Applicable Valves Series SY000 SY000 SV000 SV000 SV000 VQC000 VQC000 VQC000 S0700 Information C [dm /(s bar)] Flow-rate characteristics / / b Q [l/min] (A) ) Series SY (Side ported) (ottom ported) (Top ported) Space saving Shorten the length of the manifold using a compact SI unit mm 8 mm Cylinder drive size (eference) ø80 ø ø0 ø6 ø80 ø0 ø6 ø00 ø Akihabara UX F, --, Sotokanda, Chiyoda-ku, Tokyo 0-00, JAPA UL 00 SMC Corporation All ights eserved 09-EU6-UK - Printing OT 0KS EX60 Integrated Type (For Output) Serial Transmission System Port Solenoid Valve Series SY/SV/VQC/S0700 ohs Conventional model EX0 Power consumption (W) 0. (standard) 0. (with power saving circuit) (standard).0 (standard) ) These valves have been calculated according to ISO68 and indicate the flow rate under standard conditions with an inlet pressure of 0.6 MPa (relative pressure) and a pressure drop of 0. MPa. 0. Series S0700 eviceet is a trademark of OVA.

2 Integrated Type/For Output SI Unit Series EX60 ohs Compact design Compact design for space saving umber of outputs Each / digital output type available in the series Output polarity Each negative common (PP) / positive common (P) type available in the series Enclosure IP67 specification (IP0: For -sub connector specification units, or when connected with S0700 manifold) O/OFF switching possible with a built-in terminating resistor for communication uilt-in terminating resistor (Only for units compatible with POFIUS P with M communication connector specification) SY000/000 VQC000/000/000 S0700 SV000/000/000 How to Order SI Unit EX60 S P Communication protocol P P P P P P6 P7 P8 EC EC EC EC Protocol umber of outputs eviceet POFIUS P SI unit output polarity egative common (PP) Positive common (P) egative common (PP) Positive common (P) egative common (PP) Positive common (P) egative common (PP) Positive common (P) egative common (PP) Positive common (P) egative common (PP) Positive common (P) egative common (PP) Positive common (P) egative common (PP) Positive common (P) Communication connector M M -sub ) ) Enclosure is IP0 when the communication connector is -sub. M Manifold symbol QA QA Q Q A A C C A A

3 Integrated Type/For Output Series EX60 SI Unit Specifications EX60-SP/ EX60-SP/ EX60-SP/7 EX60-SP6/8 EX60-S/ EX60-S/ EX60-SEC/ EX60-SEC/ Model Protocol Applicable system Version eviceet P-V0 Volume (Edition.) Volume (Edition.) Conformance Test ecord V.. Specified file ) Occupied area (umber of inputs/outputs) GS file SP: 0/ SP: 0/ SP: 0/ SP: 0/ ES file SP: 0/ SP7: 0/ SP6: 0/ SP8: 0/ SEC: 0/ SEC: 0/ SEC: 0/ SEC: 0/ 00 Mbps ) Power supply.6 to 6. VC.6 to 6. VC Internal current consumption 00 ma or less 00 ma or less.8 to 6. VC Power supply to VC Internal current consumption 00 ma or less Communication connector specifications Terminator switch Output type Output specifications XML file S: 0/ S: 0/ k/0 k/00 kbps Power supply for output Power supply for communication S: 0/ S: 0/ 9.6 k/9. k/. k/9.7 k/ 87. k/00 k/. M/ M/6 M/ Mbps Communication speed Power supply for control POFIUS P ) umber of outputs M -sub uilt-in egative common (PP) M one Positive common (P) egative common (PP) Positive common (P) egative common (PP) Positive common (P) egative common (PP) Positive common (P) SP: points SP: points SP: points SP6: points S: points S: points SEC: points SEC: points SP: points SP: points SP7: points SP8: points S: points S: points SEC: points SEC: points Connection load SMC: Solenoid valve with light/surge voltage suppressor ( VC,. W or less) Supply voltage VC Supply current SP: Max..0 A SP: Max..0 A SP: Max..0 A SP6: Max..0 A S: Max..0 A S: Max..0 A SEC: Max..0 A SEC: Max..0 A SP: Max..0 A SP: Max..0 A SP7: Max..0 A SP8: Max..0 A S: Max..0 A S: Max..0 A SEC: Max..0 A SEC: Max..0 A Enclosure IP67 IP67 IP0 Operating temperature range 0 to 0 C Operating humidity range Environmental Withstand voltage resistance Insulation resistance to 8%H (o condensation) 00 VAC for min. between whole charging part and case 0 MΩ or more (00 VC) between whole charging part and case Vibration resistance 0 to 7 Hz: constant amplitude 0.7 mmp-p 7 to 0 Hz: constant acceleration 9 m/s, in each X, Y, Z direction for hrs (e-energized) Impact resistance 7 m/s Standard CE marking, UL (CSA) compatible Weight 00 g or less Mounting screw Accessories Waterproof cap (For M connector socket) pcs. EX9-AWTS ( pc.) EX9-AWTS ( pc.) ) Please note that the version is subject to change. ) In the case of, please use the Ethernet cable which is higher than CAT. ) Each file can be downloaded from the SMC Web site.

4 Series EX60 SI Unit imensions M communication connector type -sub communication connector type Functions of SI Unit Parts <LE indication and setting switch> <Setting switch> Address switch Communication speed switch Terminator switch Others ) The setting switch varies depending on the model. efer to the operation manual for details. Please download it via the SMC Web site. <LE indication> Communication state Unit power supply state Valve power supply state <Connector> M communication connector type Part no. Communication protocol EX60-SP/-SP/-SP/-SP POFIUS P EX60-S eviceet EX60-SEC Communication connector (M) US OUT pins, socket, code pins, socket, A code pins, socket, code Communication connector (M) US I pins, plug, code pins, plug, A code pins, socket, code Ground terminal M Power source connector (M) pins, plug, A code pins, plug, A code pins, plug, A code -sub communication connector type Part no. Communication protocol Ground terminal Communication connector (-sub) US I/OUT Power source connector (M) EX60-SP/-SP6/-SP7/-SP8 POFIUS P M 9 pins, socket pins, plug, A code

5 The man hours can be decreased because no e clusive tools (such as solder, crimped terminal) are re uired Also, the wire length can be ad usted at the site UIC O O E P Piercecon P Spring cage Connection P M M8 The coloring and number indication to the electrical connection makes less wrong wiring. rown M8 M White lue lack lue ust insert the connector and make / rotation. nur l rown White Align here. Make / rotation. lack CAT.ES00-7 Integrated Type/For Output Series EX60 Accessories q Communication cable with connector For SI units compatible with POFIUS P and eviceet efer to the catalogue (CAT.ES00-7) for details. M /M Connector Fieldwireable Connectors eduction in wiring time Conforming to IEC 0 0 SPEECO eduction in wiring time For SI units compatible with EX9 AC 00 E Cable length (l) 000 [mm] 00 J- ø6.7 PSJ Connector specification PSJ M plug (straight) J- connector M IP (IEC 09 ) Conforming to IEC l Plug connector pin arrangement Terminal no. Terminal no. Shield Connections (Straight cable) Core wire colours White Orange Pair White Pair 6 Green Plug connector pin arrangement w Power cable with connector (for SI units) For SI units compatible with POFIUS P, eviceet and EX00 AP 00 Cable length (l) [mm] [mm] S Connector specifications S Straight A Angle Straight connector type Angle connector type ø.9 ø6 M 8. ø6 Socket connector pin arrangement 8 8 l 0 0 Socket connector pin arrangement M. l 0 0 Terminal no. Core wire colours Terminal no. Core wire colours rown: VC + 0%/ % (Solenoid valve power supply) White: 0 V (Solenoid valve power supply) lue: VC ±0% (Control power supply) lack: 0 V (Control power supply) Grey: ot connected rown: ot connected White: VC + 0%/ % (Solenoid valve power supply) lue: ot connected lack: 0 V (Solenoid valve power supply) Grey: ot connected Connections (POFIUS P/) Connections (eviceet ) e Waterproof cap: For M connector socket Use this on ports that are not being used for communication connector (M connector socket). Use of this waterproof cap maintains the integrity of the IP67 enclosure. ) Tighten the waterproof cap with the prescribed tightening torque. (For M: 0. m) EX9 AW TS Connector type TS For M connector socket (0 pcs.) 0. M x For M connector socket

6 Plug-in Connector Connecting ase: EX60 Integrated Type (For Output) Serial Transmission System Type 0 Side Ported Series SY000/000 Type ottom Ported ohs How to Order Manifold SSY 0 S A 0 U Series Valve stations SY000 SY000 Model Side ported ottom ported The SY000 manifold base is used for mixed mounting of SY000/000 and bottom ported of SY000. When ordering, please refer to How to Order Manifold (for plug-in mixed mounting) in the Series SY catalogue. SI unit specifications 0 QA Q A C A umber of Communication outputs connector Without SI unit eviceet M M POFIUS P -sub ) M Protocol ) IP0 for the -sub applicable communication connector specification. For SI unit part number, refer to page. I rail cannot be selected for the product without SI unit. SI unit output polarity il Positive common egative common In case of the Outputs SI unit Stations 0 stations ouble wiring ) 08 8 stations 0 stations Specified layout ) (Available up to solenoids) stations ) ouble wiring: -position single, double, position and -position valves can be used on all manifold stations. Use of a -position single solenoid will result in an unused control signal. If this is not desired, order with a specified layout. ) Specified layout: Indicate the wiring specifications with the manifold specification sheet. ( that -position double, -position and position valves cannot be used where single wiring has been specified.) ) This also includes the number of blanking plate assembly. ) For the model without the SI unit (S0), note the maximum number of solenoids of the SI unit that will be mounted. If the layout is specified, indicate it on the manifold specification sheet. A, port size (Metric size) A, port Straight Elbow L L6 L8 6 8 LM SY000 SY000 SY000 ø6 One-touch fitting ø8 One-touch fitting Straight port, mixed sizes ø6 One-touch fitting ø8 One-touch fitting ø One-touch fitting ø6 One-touch fitting ø8 One-touch fitting ø8 ø0 ø0 ø One-touch fitting ø. One-touch fitting ø One-touch fitting ownward Upward C C C C6 C8 CM ø One-touch fitting Elbow port, mixed sizes (Including upward and downward piping) P, E port size (One-touch fittings) U U side ( to 0 stations) side ( to 0 stations) oth sides ( to stations) SUP/EXH block assembly specifications S Internal pilot Internal pilot/uilt-in silencer External pilot /(E) port is plugged for the built-in silencer type. When the built-in silencer type is used, keep the air outlet from coming in direct contact with water or other liquids. Mounting 0 irect mounting I rail mounting (With I rail) I rail mounting (Without I rail) For stations Specify a longer rail than the standard length. For stations Only direct mounting for Type (ottom ported). When mounted on the I rail without the SI unit, please select 0 and contact SMC for the length of the I rail. A, port size (Inch size) Type Type 0/Side ported ottom ported A, port ø/8" One-touch fitting 7 9 CM L L7 L9 7 9 LM P, E port size (One-touch fittings) Straight 0 P, E port location In case of the Outputs SI unit Stations 0 stations ouble wiring ) stations 0 stations Specified layout ) (Available up to solenoids) stations ø/" One-touch fitting ø/" One-touch fitting Type Type 0/Side ported ottom ported SY000 SY000 SY000 ø/" One-touch fitting Straight port, mixed sizes ø/" One-touch fitting ø/" One-touch fitting ø/" One-touch fitting ø/" One-touch fitting ø/" One-touch fitting Elbow ownward Upward C6 ø/" One-touch fitting Elbow port, mixed sizes (Including upward and downward piping) ø/" ø/8" ø/8" Indicate the size by means of the manifold specification sheet in case of CM, LM. The direction of P, E port fittings is the same as for A, port. If selecting LM, please indicate it on the manifold specification sheet for the P, E port fitting direction. 6

7 Plug-in Connector Connecting ase: EX60 Integrated Type (For Output) Serial Transmission System Series SY000/000 How to Order Manifold Assembly Example (SSY-0SA-) SSY-0SA-0-C6 set (Type 0 -station manifold base part no.) SY00-U sets (-position single part no.) SY00-U set (-position double part no.) SY00-U set (-position closed centre part no.) -position double ( VC) SY00-U ( set) -position single ( VC) SY00-U ( sets) -position closed centre ( VC) SY00-U ( set) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the valve, etc. U si de The valve arrangement is numbered as the st station from side. Indicate the valves to be attached below the manifold part number, in order starting from station as shown in the drawing. If the arrangement becomes complicated, then indicate on the manifold specification sheet. s on ati ) efer to page 9 for mixed mounting with top ported valves. Specify on a manifold specification sheet if plugs are required on the A and port on manifold side. St si de Manifold base ( stations) SSY-0SA-0-C6 How to Order Valves (With two mounting screws) SY 0 0 ase mounted SY000 SY000 H Type of actuation A C -position single -position double -position closed centre -position exhaust centre -position pressure centre -position dual -port valve (.C./.C.) -position dual -port valve (.O./.O.) -position dual -port valve (.C./.O.) -position dual -port valve has rubber seal type only. Seal type 0 ubber seal Metal seal Pilot specifications Internal pilot External pilot Manual override : on-locking push type ated voltage ack pressure check valve (Valve built-in type) Series one uilt-in ubber seal type only If a back pressure check valve for metal seal is required, a manifold installation type is available. Please refer to How to Order in the Series SY catalogue. However, it is not recommended to use the valve built-in type and the manifold installation type at the same time because it decreases the flow rate. -position type does not have a valve built-in type back pressure check valve. Pilot valve option Standard (0.7 MPa) Quick response type (0.7 MPa) High-pressure type (.0 MPa) Only metal seal type is available for high pressure type. K Standard T With power saving circuit (Continuous duty type) e sure to select the power saving circuit type when a valve is continuously energized for long periods of time. Quick response type does not have a power saving circuit. VC Light/surge voltage suppressor and common specifications U S Z S Z With surge voltage suppressor (on-polar) With light/surge voltage suppressor (on-polar) With surge voltage suppressor (Positive common) With light/surge voltage suppressor (Positive common) With surge voltage suppressor (egative common) With light/surge voltage suppressor (egative common) Only Z and Z types are available for the product with power saving circuit. When the SI unit specification is (positive common), select, U, S, or Z for the valve. When the SI unit specification is (negative common), select, U, S, or Z for the valve. Option for mounting Coil specifications : Push-turn locking slotted F: Slide locking type type K H With mounting screw (ound head combination screw) With mounting screw (Hexagon socket head cap screw) With mounting screw (ound head combination screw) (falling-out-prevention type) With mounting screw (Hexagon socket head cap screw) (falling-out-prevention type) For K and H, mounting screws do not fall out from the valve. (An apparatus to prevent fallingout is provided on the valve body cover.) ase gasket is not attached to manifold when a valve is ordered as a single unit. ase gasket is attached to the manifold. It needs to be ordered separately if it is needed for maintenance service. efer to the Series SY catalogue for part numbers of base gasket and mounting screw., H cannot be selected for the individual SUP., EXH. spacer assembly or double check spacer assembly with residual pressure release valve. efer to the Series SY catalogue (CAT.ES-0) for solenoid valve specifications and dimensions. efer to page for the dimensions of single SI unit. efer to the technical operation manual for details of SI unit. Protective class class (Mark: ) 7

8 Type Top Ported Plug-in Connector Connecting ase: EX60 Integrated Type (For Output) Serial Transmission System Series SY000/000 ohs How to Order Manifold SSY S A 0 U Series For mixed mounting of SY000/000, refer to How to Order Manifold (for plug-in mixed mounting) in the Series SY catalogue. ) IP0 for the -sub applicable communication connector specification. For SI unit part number, refer to page. I rail cannot be selected for the product without SI unit. SY000 SY000 SI unit specifications Protocol umber of Communication outputs connector 0 Without SI unit QA eviceet Q M A POFIUS M C P -sub ) A M SI unit output polarity Positive common egative common Valve stations In case of the Outputs SI unit 0 Stations stations 0 stations In case of the Outputs SI unit Stations 0 stations 08 0 U ) ) stations stations 8 stations stations stations P, E port location ouble wiring ) Specified layout ) (Available up to solenoids) ouble wiring ) Specified layout ) (Available up to solenoids) ) ouble wiring: -position single, double, - position and -position valves can be used on all manifold stations. Use of a -position single solenoid will result in an unused control signal. If this is not desired, order with a specified layout. ) Specified layout: Indicate the wiring specifications with the manifold specification sheet. ( that -position double, -position and -position valves cannot be used where single wiring has been specified.) ) This also includes the number of blanking plate assembly. ) For the model without the SI unit (S0), note the maximum number of solenoids of the SI unit that will be mounted. If the layout is specified, indicate it on the manifold specification sheet. U side ( to 0 stations) side ( to 0 stations) oth sides ( to stations) ) SUP/EXH block assembly specification builtin silencer type has the P port on this side. SUP/EXH block assembly specifications S Internal pilot Internal pilot/uilt-in silencer External pilot For a built-in silencer type, P and E ports are available on U and sides. /(E) port is plugged. The silencer discharge port is located on the opposite side of P, E port mounting position. (e.g., When the P, E port mounting position is, the silencer discharge port is U.) When the built-in silencer type is used, keep the air outlet from coming in direct contact with water or other liquids. P, E port size (One-touch fittings) SY000 ø8 ø/" For, sizes are in inches. 0 Mounting SY000 ø0 ø/8" irect mounting I rail mounting (With I rail) I rail mounting (Without I rail) For stations Specify a longer rail than the standard length. For stations When mounted on the I rail without the SI unit, please select 0 and contact SMC for the length of the I rail. efer to the Series SY catalogue (CAT.ES-0) for solenoid valve specifications and dimensions. efer to page for the dimensions of single SI unit. efer to the technical operation manual for details of SI unit. 8

9 Plug-in Connector Connecting ase: EX60 Integrated Type (For Output) Serial Transmission System Series SY000/000 How to Order Manifold Assembly Example (SSY-SA-) -position single ( VC) SY0-U-C6 ( sets) -position double ( VC) SY0-U-C6 ( set) -position closed centre ( VC) SY0-U-C6 ( set) SSY-SA-0 set (Type -station manifold base part no.) SY0-U-C6 sets (-position single part no.) SY0-U-C6 set (-position double part no.) SY0-U-C6 set (-position closed centre part no.) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the valve, etc. Manifold base ( stations) SSY-SA-0 side Stations U side The valve arrangement is numbered as the st station from side. Indicate the valves to be attached below the manifold part number, in order starting from station as shown in the drawing. If the arrangement becomes complicated, then indicate on the manifold specification sheet. How to Order Valves (With two mounting screws) SY 0 C6 Series Seal type 0 H SY000 SY000 Type of actuation -position single -position double -position closed centre -position exhaust centre -position pressure centre A -position dual -port valve (.C./.C.) -position dual -port valve (.O./.O.) C -position dual -port valve (.C./.O.) -position dual -port valve has rubber seal type only. ubber seal Metal seal Pilot specifications Internal pilot External pilot ack pressure check valve (Valve built-in type) one uilt-in ubber seal type only If a back pressure check valve for metal seal is required, a manifold installation type is available. Please refer to How to Order in the Series SY catalog. However, it is not recommended to use the valve built-in type and the manifold installation type at the same time because it decreases the flow rate. -position type does not have a valve built-in type back pressure check valve. Manual override Top ported K : on-locking push type : Push-turn locking slotted type Standard (0.7 MPa) Quick response type (0.7 MPa) High pressure type (.0 MPa) Only metal seal type is available for high pressure type. Coil specifications Standard T With power saving circuit (Continuous duty type) e sure to select the power saving circuit type when a valve is continuously energized for long periods of time. Quick response type does not have a power saving circuit. ated voltage VC U S Z S Z Pilot valve option Light/surge voltage suppressor and common specifications With surge voltage suppressor (on-polar) With light/surge voltage suppressor (on-polar) With surge voltage suppressor (Positive common) With light/surge voltage suppressor (Positive common) With surge voltage suppressor (egative common) With light/surge voltage suppressor (egative common) Only Z and Z types are available for the product with power saving circuit. When the SI unit specification is (positive common), select, U, S, or Z for the valve. When the SI unit specification is (negative common), select, U, S, or Z for the valve. F: Slide locking type Thread piping M 0 C C C C6 C8 F T Port size M x 0.8 /8 A and port One-touch fitting for ø One-touch fitting for ø. One-touch fitting for ø One-touch fitting for ø6 One-touch fitting for ø8 c G PT PTF Applicable series SY000 SY000 One-touch fitting (Metric size) SY000 SY000 One-touch fitting (Inch size) SY000 SY A, port size A and port One-touch fitting for ø/8" One-touch fitting for ø/" One-touch fitting for ø/" One-touch fitting for ø/" Thread type Only il is available for M. K H Option for mounting With mounting screw (ound head combination screw) With mounting screw (Hexagon socket head cap screw) With mounting screw (ound head combination screw) (falling-out-prevention type) With mounting screw (Hexagon socket head cap screw) (falling-out-prevention type) For K and H, mounting screws do not fall out from the valve. (An apparatus to prevent falling-out is provided on the valve body cover.) ase gasket is not attached to manifold when a valve is ordered as a single unit. ase gasket is attached to the manifold. It needs to be ordered separately if it is needed for maintenance service. efer to the Series SY catalogue for part numbers of base gasket and mounting screw., H cannot be selected for the individual SUP., EXH. spacer assembly or double check spacer assembly with residual pressure release valve. Protective class class (Mark: ) 9

10 Tie-rod ase: EX60 Integrated Type (For Output) Serial Transmission System Series SV ohs How to Order Manifold SSV W0S A 0 U Enclosure IP67 efer to of the SI unit specifications. Series SV000 SV000 SV000 SI unit specifications Protocol umber of outputs QA eviceet Q A POFIUS C P A I rail cannot be selected for the product without SI unit. ) IP0 for the -sub applicable communication connector specification. (The manifold part number is SSV- 0SC/.) ) For SI unit part number, refer to page. SI unit output polarity Positive common egative common Communication connector M M -sub ) M Valve stations In case of the Outputs SI unit Stations 0 stations stations In case of the Outputs SI unit Stations 0 stations 08 0 stations stations 8 stations stations stations ouble wiring ) Specified layout ) (Available up to solenoids) ouble wiring ) Specified layout ) (Available up to solenoids) ) ouble wiring: single, double, -position and -position solenoid valves can be used on all manifold stations. Use of a single solenoid will result in an unused control signal. If this is not desired, order with a specified layout. ) Specified layout: Indicate the wiring specifications with the manifold specification sheet. ( that double, -position and - position valves cannot be used where single solenoid wiring has been specified.) U S ) S ) ) When the built-in silencer type is used, keep the air outlet from coming in direct contact with water or other liquids. 0 0 P, E port location U side ( to 0 stations) side ( to 0 stations) oth sides ( to 0 stations) SUP/EXH block assembly specifications Mounting Internal pilot Internal pilot/uilt-in silencer External pilot External pilot/uilt-in silencer irect mounting I rail mounting (With I rail) I rail mounting (Without I rail) For stations When a longer I rail is desired than the specified stations. (Specify a longer rail than the For 0 stations standard length.) A, port size (Metric size) A, port size (Inch size) A, port P, E port Applicable series A, port P, E port ø. One-touch fitting ø/8" One-touch fitting ø8 ø One-touch fitting SV000 ø/" One-touch fitting One-touch fitting ø6 One-touch fitting 7 ø/" One-touch fitting ø One-touch fitting ø/" One-touch fitting ø0 ø6 One-touch fitting SV000 7 ø/" One-touch fitting One-touch fitting ø8 One-touch fitting 9 ø/" One-touch fitting ø6 One-touch fitting 7 ø/" One-touch fitting ø ø8 One-touch fitting SV000 9 ø/" One-touch fitting One-touch fitting ø0 One-touch fitting ø/8" One-touch fitting A, ports mixed M A, ports mixed C C C6 C C6 C8 C6 C8 C0 M ø/" One-touch fitting ø/8" One-touch fitting ø/8" One-touch fitting Applicable series SV000 SV000 SV000 In the case of mixed specifications (M), indicate separately on the manifold specification sheet. The port sizes of X, PE ports for external pilot specifications (, s) are ø (millimeters) or ø/" (inches) for the Series SV000/000, and ø6 (millimeters) or ø/" (inches) for the Series SV000. 0

11 Tie-rod ase: EX60 Integrated Type (For Output) Serial Transmission System Series SV How to Order Manifold Assembly Example (SV000) Manifold SSV-W0SA-0-C6 ( set) ouble solenoid SV00-FU ( sets) Single solenoid SV00-FU ( sets) U side side SSV-W0SA-0-C6 set (Manifold part no.) SV00-FU sets (Single solenoid part no.) SV00-FU sets (ouble solenoid part no.) Stations How to Order Valves SV 0 0 F ) Series A C Type of actuation SV000 SV000 SV000 -position single -position double -position closed centre -position exhaust centre -position pressure centre -position dual -port valve:.c./.c. -position dual -port valve:.o./.o. -position dual -port valve:.c./.o. -position dual -port valves are applicable to the Series SV000 and SV000 only. K one uilt-in uilt-in back pressure check valve type is applicable to the Series SV000 only. ack pressure check valve is not available for -position valve. ) efer to Specific Product Precautions in est Pneumatics o.. ated voltage VC U ack pressure check valve Light/Surge voltage suppressor With light/surge voltage suppressor With surge voltage suppressor ) Available with manifold block for station additions. efer to est Pneumatics o.. Made to Order Main valve fluoro rubber X90 (efer to page 8 in est Pneumatics o..) Pilot type Internal pilot External pilot External pilot specifications is not available for -position dual -port valves. Manual override : on-locking push type : Push-turn locking slotted type efer to the Series SV in est Pneumatics o. for solenoid valve specifications and dimensions. efer to page for the dimensions of single SI unit. efer to the technical operation manual for details of SI unit.

12 ase Mounted Plug-in Unit: EX60 Integrated Type (For Output) Serial Transmission System Series VQC000 ohs How to Order Manifold VVQC 08 C6 SA S Kit Series VQC000 Manifold model Plug-in unit Stations In case of the Outputs SI unit Stations 0 stations 0 stations In case of the Outputs SI unit Stations 0 stations ) ouble wiring: single, double, -position and -position solenoid valves can be used on all manifold stations. Use of a single solenoid will result in an unused control signal. If this is not desired, order with a specified layout. ) Specified layout: Indicate the wiring specifications with the manifold specification sheet. ( that -position double, -position and -position valves cannot be used where single wiring has been specified.) ) This also includes the number of blanking plate assembly stations stations 8 stations stations stations Kit type S Kit (Serial transmission (for output)) SI unit ouble wiring ) Specified layout ) (Available up to solenoids) ouble wiring ) Specified layout ) (Available up to solenoids) SI unit: EX60 C C C6 M CM L L L6 L 6 LM Cylinder port size With ø. One-touch fitting With ø One-touch fitting With ø6 One-touch fitting M thread Mixed sizes and with port plug Top ported elbow with ø. One-touch fitting Top ported elbow with ø One-touch fitting Top ported elbow with ø6 One-touch fitting M thread ottom ported elbow with ø. One-touch fitting ottom ported elbow with ø One-touch fitting ottom ported elbow with ø6 One-touch fitting M thread Elbow port, mixed sizes ) Indicate the size by means of the manifold specification sheet in case of CM, LM. ) s for inch sizes are as follows: : ø/8" : ø/" 7: ø/" M: Mixed The top ported elbow is L and the bottom ported elbow is. IP0 specification IP67 specification S0 SQA SQ SA S SC S SA S Protocol eviceet POFIUS P Option one All stations with back pressure check valve With I rail (ail length: Standard) With I rail (ail length: Special) K Special wiring spec. (Except double wiring) With name plate External pilot ) S irect EXH outlet with built-in silencer umber of outputs Without SI unit SI unit output polarity Communication connector M M -sub ) M ) -sub S kit: IP0 specification (IP67 specification for all other S kits) ) For SI unit part number, refer to page. Positive common egative common ) ) ) 6) ) When two or more symbols are specified, indicate them alphabetically. Example: -S ) When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. ) For special I rail length, indicate. (Enter the number of stations inside.) Example: -08 In this case, stations will be mounted on a I rail for 8 stations regardless of the actual number of manifold stations. The specified number of stations must be larger than the number of stations on the manifold. Indicate -0 for the option without I rail. ) Specify wiring type of each station by means of the manifold specification sheet. ) For external pilot option, -, indicate the external pilot specification for the applicable valves as well. 6) uilt-in silencer type does not satisfy IP67. 7) When the S0 (Without SI unit) is specified, -, - cannot be selected.

13 Plug-in Unit: EX60 Integrated Type (For Output) Serial Transmission System Series VQC000 How to Order Valves VQC 0 0 Series VQC000 () A Type of actuation -position single ()(P) () -position double (Metal) () ()(P) () -position double (ubber) () ()(P) () -position closed centre () () (P) () -position exhaust centre () ) ) ) C -position dual -port valve ().C. ().O. ().C. (P) (P) (P) ) ubber seal only () ().C. -position dual -port valve () () ().O. -position dual -port valve (C) () ().O. Seal 0 Function K ) ) ) Metal seal ubber seal Standard (0. W) High-speed response type (0.9 W) High-pressure type (.0 MPa, 0.9 W) egative common External pilot ) When two or more symbols are specified, indicate them alphabetically. However, combination of and K is not possible. ) Metal seal only ) When -COM. is specified for the SI unit, select and mount the valve of negative common. ) ual -port is not applicable. Coil voltage VC Light/surge voltage suppressor Yes Manual override : on-locking push type (Tool required) A A A : Locking type (Tool required) C: Locking type (Manual) : Slide locking type (Manual) () (P)() -position pressure centre () () (P)() efer to the Series VQC catalogue (CAT.ES-0) for solenoid valve specifications and dimensions. efer to page for the dimensions of single SI unit. efer to the technical operation manual for details of SI unit.

14 ase Mounted Plug-in Unit: EX60 Integrated Type (For Output) Serial Transmission System Series VQC000 ohs How to Order Manifold VVQC 08 C6 SA S Kit Series VQC000 Manifold model Plug-in unit Stations In case of the Outputs SI unit Stations 0 stations 0 stations In case of the Outputs SI unit Stations 0 stations 08 0 stations stations 8 stations stations stations Kit type S Kit (Serial transmission (for output)) SI unit ouble wiring ) Specified layout ) (Available up to solenoids) ouble wiring ) Specified layout ) (Available up to solenoids) ) ouble wiring: single, double, -position and -position solenoid valves can be used on all manifold stations. Use of a single solenoid will result in an unused control signal. If this is not desired, order with a specified layout. ) Specified layout: Indicate the wiring specifications with the manifold specification sheet. ( that -position double, -position and -position valves cannot be used where single wiring has been specified.) ) This also includes the number of blanking plate assembly. C C6 C8 CM L L6 L8 6 8 LM ø One-touch fitting ø6 One-touch fitting ø8 One-touch fitting Mixed sizes and with port plug Top ported elbow with ø One-touch fitting Top ported elbow with ø6 One-touch fitting Top ported elbow with ø8 One-touch fitting ottom ported elbow with ø One-touch fitting ottom ported elbow with ø6 One-touch fitting ottom ported elbow with ø8 One-touch fitting Elbow port, mixed sizes ) Indicate the size by means of the manifold specification sheet in case of CM, LM. ) s for inch sizes are as follows: : ø/" 7: ø/" 9: ø/" M: Mixed The top ported elbow is L and the bottom ported elbow is. Cylinder port size SI unit specifications Positive common egative common S0 SQA SQ SA S SC S SA S Protocol eviceet POFIUS P Option one All stations with back pressure check valve With I rail (ail length: Standard) With I rail (ail length: Special) K Special wiring spec. (Except double wiring) With name plate External pilot ) S irect EXH outlet with built-in silencer T ranched P and ports on U-side umber of outputs Without SI unit Communication connector M M -sub ) M ) -sub S kit: IP0 specification (IP67 specification for all other S kits) ) For SI unit part number, refer to page. ) ) ) 6) 7) ) When two or more symbols are specified, indicate them alphabetically. Example: -S ) When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. ) For special I rail length, indicate. (Enter the number of stations inside.) Example: -08 In this case, stations will be mounted on a I rail for 8 stations regardless of the actual number of manifold stations. The specified number of stations must be larger than the number of stations on the manifold. Indicate -0 for the option without I rail. ) Specify wiring type of each station by means of the manifold specification sheet. ) For external pilot option, -, indicate the external pilot specification for the applicable valves as well. 6) uilt-in silencer type does not satisfy IP67. 7) SUP and EXH ports on the U-side (on cylinder port side and coil side is branched.) Port is equipped with Onetouch fitting for ø. 8) When the S0 (Without SI unit) is specified, -, - cannot be selected. SI unit: EX60 IP0 specification IP67 specification

15 Plug-in Unit: EX60 Integrated Type (For Output) Serial Transmission System Series VQC000 How to Order Valves VQC 0 0 Series VQC000 () A Type of actuation -position single () (P)() -position double (Metal) () () (P)() -position double (ubber) () () (P)() -position closed centre () ()(P) () -position exhaust centre () ()(P) () ) ) ) C -position dual -port valve ().C. ().O. ().C. (P) (P) (P) ) ubber seal only () ().C. -position dual -port valve () () ().O. -position dual -port valve (C) () ().O. 0 Seal Function K ) ) ) Metal seal ubber seal Standard (0. W) High-speed response type (0.9 W) High-pressure type (.0 MPa, 0.9 W) egative common External pilot ) When two or more symbols are specified, indicate them alphabetically. However, combination of and K is not possible. ) Metal seal only ) When -COM. is specified for the SI unit, select and mount the valve of negative common. ) ual -port is not applicable. Coil voltage VC Light/surge voltage suppressor Yes Manual override : on-locking push type (Tool required) : Locking type (Tool required) C: Locking type (Manual) : Slide locking type (Manual) -position pressure centre () ()(P) () efer to the Series VQC catalogue (CAT.ES-0) for solenoid valve specifications and dimensions. efer to page for the dimensions of single SI unit. efer to the technical operation manual for details of SI unit.

16 ase Mounted Plug-in Unit: EX60 Integrated Type (For Output) Serial Transmission System Series VQC000 ohs How to Order Manifold VVQC 0 SA S Kit Series Stations SI unit specifications VQC000 In case of the Outputs SI unit Stations Manifold model 0 station Plug-in unit ouble wiring ) stations 0 station C8 C0 C 0 0 CM Cylinder port size With ø8 One-touch fitting With ø0 One-touch fitting With ø One-touch fitting c/ c/8 ottom ported c/ Mixed ) Indicate the size by means of the manifold specification sheet in case of CM. ) s for inch sizes are as follows: <In case of One-touch fittings> 7: ø/" 9: ø/" : ø/8" M: Mixed Thread type F T c G PT/PTF stations In case of the Outputs SI unit Stations 0 station stations station stations Specified layout ) (Available up to solenoids) ouble wiring ) Specified layout ) (Available up to solenoids) ) ouble wiring: single, double, -position and -position solenoid valves can be used on all manifold stations. Use of a single solenoid will result in an unused control signal. If this is not desired, order with a specified layout. ) Specified layout: Indicate the wiring specifications with the manifold specification sheet. ( that -position double, -position and -position valves cannot be used where single wiring has been specified.) ) This also includes the number of blanking plate assembly. Positive common egative common Option one S irect EXH outlet with built-in silencer ) K Special wiring spec. (Except double wiring) ) ) uilt-in silencer type does not satisfy IP67. ) Specify wiring type of each station by means of the manifold specification sheet. Kit type S Kit (Serial transmission (for output)) SI unit S0 SQA SQ SA S SC S SA S Protocol eviceet POFIUS P umber of outputs Without SI unit Communication connector M M -sub ) M ) -sub S kit: IP0 specification (IP67 specification for all other S kits) ) For SI unit part number, refer to page. SI unit: EX60 IP0 specification IP67 specification

17 Plug-in Unit: EX60 Integrated Type (For Output) Serial Transmission System Series VQC000 How to Order Valves VQC 0 0 Series VQC000 () Type of actuation -position single ()(P)() -position double (Metal) () ()(P)() -position double (ubber) -position exhaust centre () () (P)() -position pressure centre () () (P)() -position double check Seal 0 Y ) Function Metal seal ubber seal Standard ( W) External pilot Low wattage type (0. W) ) When two or more symbols are specified, indicate them alphabetically. ) Select Y when a valve is continuously energized Manual override : on-locking push type (Tool required) : Locking type (Tool required) () ()(P)() -position closed centre () 6 () () (P)() Coil voltage VC Light/surge voltage suppressor Yes ()(P)() efer to the Series VQC in est Pneumatics o. for solenoid valve specifications and dimensions. efer to page for the dimensions of single SI unit. efer to the technical operation manual for details of SI unit. 7

18 Plug-in Manifold Stacking ase S Kit (Serial Transmission): EX60 Integrated Type (For Output) Serial Transmission System Series S0700 ohs How to Order Manifold SS C C8 SA C C C CM M Stations In case of the Outputs SI unit 0 Stations station 0 stations station stations Cylinder port size ouble wiring ) Specified layout ) (Available up to solenoids) In case of the Outputs SI unit 0 Stations station stations station stations ouble wiring ) Specified layout ) (Available up to solenoids) ) ouble wiring: single, double, -position and -position solenoid valves can be used on all manifold stations. Use of a single solenoid will result in an unused control signal. If this is not desired, order with a specified layout. ) Specified layout: Indicate the wiring specifications with the manifold specification sheet. ( that -position double, -position and -position valves cannot be used where single wiring has been specified.) ) This also includes the number of blanking plate assembly. Port size With ø One-touch fitting With ø. One-touch fitting With ø One-touch fitting Mixed sizes and with port plug ) With ø/8" One-touch fitting With ø/" One-touch fitting Mixed sizes and with port plug ) Metric Inch ) Specify Mixed sizes and with port plug by means of the manifold specification sheet. C6 C8 7 9 ) The cylinder port is ø/" when measured in inches. Type of actuation umber of solenoids P, port size Port size With ø8 One-touch fitting ) With ø6 One-touch fitting With ø8 One-touch fitting With ø/" One-touch fitting With ø/" One-touch fitting Single Positive common egative common Metric Inch Kit type Protocol umber of Communication outputs connector S0 Without SI unit SQA eviceet SQ SA S SA SC P S S POFIUS M M -sub M ) The maximum number of stations is determined by the total number of solenoids. For mixed single and double wirings, enter -K to the order code options. ) For SI unit part number, refer to page. SI unit specifications ouble, ual -port ) 0 ) K ) S Option ) Option one With back pressure check valve (All stations) With I rail (ail length: Standard) Without I rail (With bracket) With I rail esignated length (: Station) Special wiring specifications (Except double wiring) With name plate External pilot uilt-in silencer ) When two or more options are specified, indicate them alphabetically. Example) -K ) When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. ) The available number of stations is larger than the number of manifold stations. ) Indicate the wiring specifications for mixed single and double wirings. ) For details, refer to page 6 in the Series S0700 catalogue. For manifold optional parts, refer to pages 6 to 69 in the Series S0700 catalogue. For exploded view of manifold, refer to page 7 in the Series S0700 catalogue. When the S0 (Without SI unit) is specified, -, - cannot be selected. 8

19 Plut-in Manifold Stacking ase S Kit (Serial Transmission): EX60 Integrated Type (For Output) Serial Transmission System Series S0700 How to Order Manifold Assembly Example (Serial transmission kit) Stations side U side SS070-0CSA set Manifold base part no. S070- sets Valve part no. (Stations to ) Prefix the asterisk to the part nos. of the solenoid valve, etc. Write sequentially from the st station on the side. When part nos. written collectively are complicated, specified by means of the manifold specification sheet. Specify the part numbers for valves and options together beneath the manifold base part number. How to Order Valves S07 0 A C Type of actuation Port size -position single -position double -position dual -port (.C. +.C.) [Exhaust centre] -position dual -port (.O. +.O.) [Pressure centre] -position dual -port (.C. +.O.) ) For symbol, refer to page 7 in the Series S0700 catalogue. Voltage: VC Function Specifications Standard External pilot ) ) ot compatible with dual -port valves. ase mounted plug-in efer to the Series S0700 catalogue (CAT.ES-88) for solenoid valve specifications and dimensions. efer to page for the dimensions of single SI unit. efer to the technical operation manual for details of SI unit. 9

20 Safety Instructions Caution: Warning: anger : Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. anger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or anger. They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC) ), and other safety regulations. ) ISO : Pneumatic fluid power General rules relating to systems. ISO : Hydraulic fluid power General rules relating to systems. IEC 600-: Safety of machinery Electrical equipment of machines. (Part : General requirements) ISO 08-: Manipulating industrial robots - Safety. etc. Warning. The compatibility of the product is the responsibility of the person who designs the equipment or decides its specifications. Since the product specified here is used under various operating conditions, its compatibility with specific equipment must be decided by the person who designs the equipment or decides its specifications based on necessary analysis and test results. The expected performance and safety assurance of the equipment will be the responsibility of the person who has determined its compatibility with the product. This person should also continuously review all specifications of the product referring to its latest catalogue information, with a view to giving due consideration to any possibility of equipment failure when configuring the equipment.. Only personnel with appropriate training should operate machinery and equipment. The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced.. o not service or attempt to remove product and machinery/equipment until safety is confirmed.. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.. When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any appropriate source is cut, and read and understand the specific product precautions of all relevant products carefully.. efore machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.. Contact SMC beforehand and take special consideration of safety measures if the product is to be used in any of the following conditions.. Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight.. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping, vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or other applications unsuitable for the standard specifications described in the product catalogue.. An application which could have negative effects on people, property, or animals requiring special safety analysis.. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. Caution. The product is provided for use in manufacturing industries. The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult SMC beforehand and exchange specifications or a contract if necessary. If anything is unclear, contact your nearest sales branch. Limited warranty and isclaimer/ Compliance equirements The product used is subject to the following Limited warranty and isclaimer and Compliance equirements. ead and accept them before using the product. Limited warranty and isclaimer. The warranty period of the product is year in service or. years after the product is delivered. ) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch.. For any failure or damage reported within the warranty period which is clearly our responsibility, a replacement product or necessary parts will be provided. This limited warranty applies only to our product independently, and not to any other damage incurred due to the failure of the product.. Prior to using SMC products, please read and understand the warranty terms and disclaimers noted in the specified catalogue for the particular products. ) Vacuum pads are excluded from this year warranty. A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty. Compliance equirements. The use of SMC products with production equipment for the manufacture of weapons of mass destruction (WM) or any other weapon is strictly prohibited.. The exports of SMC products or technology from one country to another are governed by the relevant security laws and regulations of the countries involved in the transaction. Prior to the shipment of a SMC product to another country, assure that all local rules governing that export are known and followed. Safety Instructions e sure to read Handling Precautions for SMC Products (M-E0-) before using. SMC Corporation (Europe) Austria office@smc.at elgium + (0)6 info@smcpneumatics.be ulgaria office@smc.bg Croatia office@smc.hr Czech epublic office@smc.cz enmark smc@smcdk.com Estonia smc@smcpneumatics.ee Finland smcfi@smc.fi France + (0) contact@smc-france.fr Germany +9 (0) info@smc-pneumatik.de Greece sales@smchellas.gr Hungary office@smc.hu Ireland + (0) sales@smcpneumatics.ie Italy +9 (0)97 mailbox@smcitalia.it Latvia info@smclv.lv Lithuania info@smclt.lt etherlands + (0) info@smcpneumatics.nl orway post@smc-norge.no Poland office@smc.pl Portugal postpt@smc.smces.es omania smcromania@smcromania.ro ussia info@smc-pneumatik.ru Slovakia + office@smc.sk Slovenia office@smc.si Spain post@smc.smces.es Sweden +6 (0) post@smcpneumatics.se Switzerland + (0)96 info@smc.ch Turkey +90 (0)076 smc@entek.com.tr UK + (0)8 sales@smcpneumatics.co.uk SMC COPOATIO Akihabara UX F, --, Sotokanda, Chiyoda-ku, Tokyo 0-00, JAPA Phone: FAX: st printing OZ printing OZ 00 Printed in Spain Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.