SMC guide to ATEX compliant products

Transcription

1 SMC guide to ATEX compliant products P-E13-23A A

2 ATEX Directive Directive 94/9/EC Equipment and Protective Systems intended for use in potentially Explosive Atmospheres Outline of ATEX directive Since 1st July 2003, equipment used in potentially explosive atmospheres within the EU is required to comply with the ATEX directive. CE Marking and ATEX All equipment within the scope of the Directive must bear the CE marking and comply with the directive's requirements. ATEX Directive incorporates conventional European standards for explosion-proof equipment. Objective of the ATEX Directive Major objective of the ATEX Directive is as follows: Preventing electrostatic discharge Preventing ignition likely to be caused by electrical sparks generated from friction, shock, and wear Preventing ignition under the influence of elevated temperatures due to friction, shock, and wear Concentrating on the duties of the manufacturers Certifying equipment to the ATEX directive by Zone/Category Zone/Category classification The ATEX directive defines the categories of equipment and protective systems, which can be used in the corresponding zones as per the following table: Zone Equipment category Presence of the explosive atmosphere Zone 0 Category 1 Zone 2 Category 3 Zone 1 Category Continuously or for long periods >1000 hours/year Occasionally 10 to 1000 hours/year Rarely or for short periods <10 hours/year SMC's Support SMC's products corresponding to ATEX Directive SMC's products which are within the scope of the ATEX Directive include electrical equipment and mechanical equipment such as pneumatic actuators (cylinders). SMC prepares pneumatic equipment for all industries compliant with the ATEX Directive to help our customers make a system corresponding to the Directive. Certification Procedure Our products are categorized as electrical and non-electrical products, and tested and certified as follows: ATEX Category Category 1 Category 2 ( Electrical products Solenoid valve, auto switch, serial transmission system, electro-pneumatic positioner, etc. ) Certification method 1. Technical file 2. Quality audit 3. Type approval test 1. Technical file 2. Quality audit 3. Type approval test Certified by Certification authority Certification authority Certification authority Certification authority Certification authority Certification authority Non-electrical products (Cylinder, rotary actuator, etc.) Certification method 1. Technical file 2. Quality audit 3. Type approval test 1. Technical file (to be stored in the certification authority) 2. Quality: In-house manufacturing control Certified by Certification authority Certification authority Certification authority SMC SMC Category 3 1. Technical file 2. In-house production control SMC SMC 1. Technical file 2. In-house production control SMC SMC 1

3 INDEX <Note for ordering ATEX compliant products> Some items may not be compliant with the ATEX Directive. For details, refer to. For Self Declaration of Conformity, refer to our sales representative. Pneumatic Solenoid Valve ist of ATEX compliant products 5 Port Solenoid Valve: 52-SY5000/7000/ Port Solenoid Valve: 56-VQC1000/2000/4000 Category Page no Serial Transmission System Integrated Type: For Input/Output: 56-EX250 Decentralized Serial Wiring (GW system, 4 branches): 56-EX Air Cylinder Air Cylinder: 55-C76 ISO Cylinder: 55-C85 ISO Cylinder: 55-C95 (s: 160, 200, 250) ISO Cylinder: 55-C96 (-C) ISO Cylinder: 55-CP96 (-C) IISO Cylinder: 55-C55 Air Cylinder: 55-CG1 Air Cylinder: 55-CS1 Compact Cylinder: 55-CQ2 Dual Rod Cylinder: 55-CXS Mechanically Jointed Rodless Cylinder/asic Type: 55-MY1 Mechanically Jointed Rodless Cylinder/Slide earing Guide Type: 55-MY1M Mechanically Jointed Rodless Cylinder/inear Guide Type: 55-MY1H Auto Switch Solid State Switch Reed Switch Rotary Actuator Rotary Actuator: 55-CR1 Rotary Actuator: 56-CR1 Rotary Actuator: 55-CR2-Z Rotary Actuator: 56-CR2-Z Rotary Actuator/Free Mount Type: 55-CRU2-Z Rotary Actuator/Free Mount Type: 56-CRU2-Z Compact Rotary Actuator: 55-CRQ2 Compact Rotary Actuator: 56-CRQ ooster Regulator ooster Regulator: 56-VA 96 Pressure Switch 2-Color Display Digital Pressure Switch: 56-ISE70/75 (H) 97 2 Port Valve for Fluid Control Steam Valve: 56-VND 99 Process Valve Valve for Water and Chemical ase Fluids (2/3 port air operated valve): VCC Air Operated Chemical Valve/Threaded Type: 55-VA Process Pumps/Automatically Operated Type (Internal switching type) Air Operated Type (External Switching Type): 55-PA3000/5000 Air Operated Type (External Switching Type): 56-PA3000/ Instrumentation Equipment Pneumatic-Pneumatic Positioner: 55-IP5000/5100 Pneumatic-Pneumatic Positioner: 56-IP5000/5100 Electro-Pneumatic Positioner: IP6000-X14/IP6100-X14 Electro-Pneumatic Positioner: IP8000-X14/IP8100-X14 Smart Positioner: 52-IP8001/52-IP8101 Cylinder Positioner: 56-IP a

4 5 Port Solenoid Valve Series 52-SY II 2G Ex ia IIC T4...T5 Gb Ta 10 C to50 C 0344 II 2G Ex ia IIC T6 Gb Ta 10 C to 45 C How to order 52 SY F ATEX category Series 52-SY SY SY9000 racket Without bracket F1 With foot bracket Note 1) F2 With side bracket Note 1) 2 position single solenoid valve only. Note 2) 52-SY9000 has no bracket Type of actuation 2-position single 2-position double 3-position closed centre 3-position exhaust centre 3-position pressure centre 2 4 Piping type ody ported type ase mounted type Pilot type Internal pilot R Note) External pilot Note) ase mounted type only. A F TT arrier Without barrier Z728.H KFD0-SD2-Ex Note) One barrier per solenoid supplied. Additionally, when the barrier is selected, the barriers equivalent to the number of solenoids are included with the product. Electrical entry Plug connector type Plug connector with cover type Cable type Note) TT-type is connected to the terminal block. Cables other than the connected one cannot be used ead wire length 300 mm 600 mm 1000 mm 1500 mm 2000 mm 3000 mm mm (Semi-standard) type has 300 mm and 600 mm only. Thread type F N T Rc G NPT NPTF A, port size (ody ported type) Symbol 01 C4 C6 C8 N3 N7 N9 02 C8 C10 N9 N C8 C10 C12 N9 N11 Port size 1/8 One-touch fitting for ø4 One-touch fitting for ø6 One-touch fitting for ø8 One-touch fitting for ø5/32" One-touch fitting for ø1/4" One-touch fitting for ø5/16" 1/4 One-touch fitting for ø8 One-touch fitting for ø10 One-touch fitting for ø5/16" One-touch fitting for ø3/8" 1/4 3/8 One-touch fitting for ø8 One-touch fitting for ø10 One-touch fitting for ø12 One-touch fitting for ø5/16" One-touch fitting for ø3/8" Applicable series 52-SY SY SY9000 Port size (ase mounted type) Symbol Port size Applicable series 02 1/4 Without sub-plate 52-SY /4 3/ /8 1/2 52-SY SY9000 Manual override D E Non-locking push type Push-turn locking slotted type Push-turn locking lever type 3 D

5 5 Port Solenoid Valve Series 52-SY Specifications Series Ambient and fluid temperature Coil temperature rise Temperature class T6 Temperature class T4, T5 arrier input voltage (non hazardous area) Coil rated voltage (hazardous area) Intrinsically safe Gas group Protection type Plug connector type rating TT type Cable type 52-SY SY SY to 45 C (No freezing) 10 to 50 C (No freezing) 40 C less (at rated) 24 VDC (system rated voltage) at 1.1 W 12 VDC at 0.52 W ia IIC IP30 ( type : IP40) IP65 Note) Impact resistance: No malfunction resulted from the impact test using a drop impact tester. The test were performed one time each in the axial and right angle directions of the main valve and armature, in both energized and de-energized states (Valve in the initial stage). Vibration resistance: No malfunction occurred in a one-sweep test between 8.3 and 2000Hz. The test was performed for both energized and de-energized states in the axial and right angle directions of the main valve and armature (valve in the initial stage). Standard SY manifolds Types 20, 41, 42 are used for 52-SY valves. Safety Instructions 1) This product is not suitable for Zone 0. The suitable zones are Zones 1 and 2. 2) SMC-TAS and TAV Series, antistatic tubing, are available if required. 3) The solenoid valve has polarity. Confirm the correct polarity by observing the color of the lead aires. if the polarity is reversed, the barrier may be damaged. 4) Confirm that the solenoid input voltage at the lead wires is 10.8 VDC (min). 5) This product must be connected to an appropriate barrier (ATEX compliant product), or a certified intrinsically safe circuit, with the following maximum values. Ui = 28 V li = 225 ma (resistively limited) Pi = 1 W Ci = 0 nf i = 0 mh Response time Type of actuation 2-position single 2-position double 3-position 52-SY or less 22 or less 38 or less Response time (ms) (0.5 MPa) 52-SY or less 30 or less 56 or less Note 1) According to dynamic performance test JIS Note 2) Response time when barriers were combined with a valve. System A: Valve + Z728.H F: Valve + KFD0-SD2-Ex SY or less 50 or less 70 or less Manifold Specifications for 20 Type Model Applicable valve Manifold style 1 (SUP) / 3/5 (EXH) Valve stations 4/2 (A/) ocation SS5Y SY520 Single base / mounting Common SUP / Common EXH 2 to 20 (1) Valve SS5Y SY720 1,3,5 (P,EA,E) Port 1/4 1/8 Port size C4 (One-touch fitting for ø4) 1/4 4,2 (A,) Port C8 (One-touch fitting for ø8) C6 (One-touch fitting for ø6) C10 (One-touch fitting for ø10) C8 (One-touch fitting for ø8) Manifold base weight W (g) n: Station W = 36n + 6 W = 43n + 64 Note 1) For more than 10 stations (more than 5 stations in case of SS5Y7), supply pressure to P port on both sides and exhaust from EA/E port on both side. Note 2) 52-SY920 valve are not available with manifold as standard. Manifold Specifications for 20 Type Port size Flow characteristics Model 1,5,3 4,2 1 4/2 (P A/) 4/2 5/3 (A/ EA/E) (P,EA,E) (A,) c[dm 3 /(s bar)] b Cv c[dm 3 /(s bar)] b Cv SS5Y5-20 SS5Y7-20 1/4 1/4 C8 C Note) Values for 5 stations manifold with a 2 position single type valve. Manifold Specifications for 41 and 42 Type Manifold Specifications for 41 and 42 Type Model SS5Y5-41 SS5Y5-42 SS5Y7-42 Applicable valve 52-SY SY740 Manifold style 1 (SUP) / 3/5 (EXH) Valve stations Single base / mounting Common SUP / Common EXH 2 to 20 (1) 4/2 (A/) Porting spec. ocation Direction ase Side 1,3,5 (P,EA,E) Port 1/4 1/4 Port size 1/8 1/4 1/4 4,2 (A,) Port C6 (One-touch fitting for ø6) C6 (One-touch fitting for ø6) C8 (One-touch fitting for ø8) C8 (One-touch fitting for ø8) C10 (One-touch fitting for ø10) Manifold base weight W (g) n: Station W = 61n W = 79n W = 100n Note 1) For more than 10 stations (more than 5 stations in case of SS5Y7), supply pressure to P port on both sides and exhaust from EA/E port on both side. Note 2) 52-SY940 valve are not available with manifold as standard. Note 3) 52-SY series are not available with resin type manifold (45 type). Model SS5Y5-41 SS5Y5-42 SS5Y7-42 Port size 1,5,3 (P,EA,E) 1/4 1/4 1/4 4,2 (A,) C8 C8 C10 Flow characteristics 1 4/2 (P A/) 4/2 5/3 (A/ EA/E) c[dm 3 /(s bar)] b Cv c[dm 3 /(s bar)] b Cv Note) Values for 5 stations manifold with a 2 position single type valve. 4 C

6 ody Ported Type Series 52-SY5000 Dimensions 2-position single plug connector () 52-SY (-F2) In case with foot bracket 52-SY F Insulation: lack ( ) Insulation: Red (+) Manual override (2 x ø3.2 Mounting holes) A (37) 2 x M3 x 0.5 Threads depth 3.5 (For bracket mounting) x ø3.2 (Mounting holes for manifold) 2 x 1/8" A (4), (2) port x ø3.2 (Mounting holes) (1.2) mm 2 ø (For E type) (32.3) (36.7) (40.2) (11.7) (ead wire length) x 1/8" {P (1), EA (5), E (3) port} x ø2.2 (Positioning for manifold gasket) EA P 27.2 (45) E 15 (20) plug connector with cover () 52-SY (-F2) Insulation: Red (+) Insulation: lack ( ) ø mm mm 2 Cable type (TT) 52-SY5120-TT-01 (-F2) ead wire marking No.1 (+), No.2 ( ) ø (ead wire length) (ead wire length) Max.10 5

7 ody Ported Type Series 52-SY5000 Dimensions 2-position double plug connector () 52-SY (-F2) x M3 x 0.5 Threads depth 3.5 (For bracket mounting) Insulation: lack ( ) 11.6 Insulation: Red (+) Manual override A x ø3.2 (Mounting holes for manifold) 2 x 1/8" {A (4), (2) port} 37 (2 x ø3.2 Mounting holes) mm 2 ø (For E type) (40.2) (36.7) (1.2) (11.7) (ead wire length) 3 x 1/8" {P (1), EA (5), E (3) port} (76.8) EA P E 15 (20) 2 x ø2.2 (Positioning for manifold gasket) 27.2 (45) plug connector with cover () 52-SY (-F2) (ead wire length) Insulation: Red (+) Insulation: lack ( ) ø (71.7) 177 ø mm 2 Cable type (TT) 52-SY5220-TT-01 (-F2) (ead wire length) Max.10 ead wire marking No.1 (+), No.2 ( ) 0.75 mm 2 12 (88.5) 6

8 ody Ported Type Series 52-SY5000 Dimensions 3-position closed centre/ exhaust centre/pressure centre plug connector () 3 52-SY (-F2) x M3 x 0.5 Threads depth 3.5 (For bracket mounting) (89.4) Insulation: lack ( ) 11.6 Insulation: Red (+) Manual override A (37) 2 x ø3.2 (Mounting holes for manifold) 2 x 1/8" {A (4), (2) port} (2 x ø3.2 Mounting holes) mm 2 ø (For E type) (40.2) (36.7) (1.2) (ead wire length) 3 x 1/8" {P (1), EA (5), E (3) port} EA P E 15 (20) 2 x ø2.2 (Positioning for manifold gasket) 27.2 (45) plug connector with cover () 3 52-SY (-F2) 5 (ead wire length) 156 Insulation: Red (+) Insulation: lack ( ) ø ø mm 2 Cable type (TT) 3 52-SY5420-TT-01 (-F2) 5 (ead wire length) Max.10 ead wire marking No.1 (+), No.2 ( ) 0.75 mm

9 ody Ported Type Series 52-SY7000 Dimensions 2-position single plug connector () 52-SY (-F2) In case with foot bracket 52-SY (F1) 1.2 Insulation: lack ( ) Insulation: Red (+) (14) mm 2 2 x M4 x 0.7 Threads depth 6.5 (For bracket mounting) Manual override 44 (For E type) A (52) 29.4 (39.4) x ø4.2 (Mounting holes for manifold) 2 x 1/4" {A (4), (2) port} (2 x ø4.2 Mounting holes) 40 (42.5) (49.5) (ead wire length) 2 x 1/8" {EA (5), E (3) port} 1/4" {P (1) port} EA P E 18 (23.9) x ø2.2 (Positioning for manifold gasket) 36 (66) plug connector with cover () 52-SY (-F2) Insulation: Red (+) Insulation: lack ( ) ø mm Cable type (TT) 52-SY7120-TT-02 (-F2) (ead wire length) ead wire marking No.1 (+), No.2 ( ) ø mm 2 12 (ead wire length) Max

10 ody Ported Type Series 52-SY7000 Dimensions 2-position double plug connector () 52-SY (-F2) 20 2 x M4 x 0.7 Threads depth 6.5 (For bracket mounting) Insulation: lack ( ) Insulation: Red (+) Manual override A (52) x ø4.2 (Mounting holes for manifold) 2 x 1/4" {A (4), (2) port} (2 x ø4.2 Mounting holes) (1.2) (14) mm 2 ø (For E type) 2 (49.5) (ead wire length) 1/4" {P (1) port} 2 x 1/8" {EA (5), E (3) port} (42.5) 0.9 (83.9) EA P E 18 2 x ø2.2 (Positioning for manifold gasket) 36 (66) (23.9) plug connector with cover () 52-SY (-F2) (ead wire length) Insulation: Red (+) Insulation: lack ( ) ø mm (78.8) Cable type (TT) 52-SY7220-TT-02 (-F2) Max (ead wire length) ead wire marking No.1 (+), No.2 ( ) ø mm 2 12 (95.6) 9

11 ody Ported Type Series 52-SY7000 Dimensions 3-position closed centre/exhaust centre/pressure centre plug connector () 3 52-SY (-F2) x M4 x 0.7 Threads depth 6.5 (For bracket mounting) Insulation: lack ( ) Insulation: Red (+) Manual override A (52) x ø4.2 (Mounting holes for manifold) 2 x 1/4" {A (4), (2) port} (2 x ø4.2 Mounting holes) (1.2) (14) mm 2 ø (For E type) 2 (49.5) (ead wire length) 1/4" {P (1) port} 2 x 1/8" {EA (5), E (3) port} (42.5) EA P E 18 2 x ø2.2 (Positioning for manifold gasket) 36 (66) (23.9) plug connector with cover () 3 52-SY (-F2) (ead wire length) Insulation: Red (+) Insulation: lack ( ) ø mm Cable type (TT) 3 52-SY7420-TT-02 (-F2) 5 Max (ead wire length) ead wire marking No.1 (+), No.2 ( ) ø mm

12 ody Ported Type Series 52-SY9000 Dimensions 2-position single plug connector () 52-SY Insulation: lack ( ) (56.3) 4A Insulation: Red (+) Manual override x ø3.2 (Mounting holes for manifold) 2 x 1/4", 3/8" {4 (A), 2 () port} (12) mm 2 ø1.55 (ead wire length) 46 (For E type) 2 x ø4.4 (Mounting holes) x 1/4" {1 (P), 3 (E), 5 (EA) port} 5EA P E plug connector with cover () 52-SY Insulation: Red (+) Insulation: lack ( ) ø mm (ead wire length) Cable type (TT) SY9120-TT- 03 ead wire marking No.1 (+), No.2 ( ) 0.75 mm (ead wire length) Max.10 11

13 ody Ported Type Series 52-SY9000 Dimensions 2-position double plug connector () 52-SY Insulation: lack ( ) A 2 Insulation: Red (+) Manual override x ø3.2 (Mounting holes for manifold) 2 x 1/4", 3/8" {4 (A), 2 () port} (12) mm 2 ø1.55 (ead wire length) 46 (For E type) P ø (ead wire length) x ø4.4 (Mounting holes) 3 x 1/4" {1 (P), 3 (E), 5 (EA) port} 5EA 10 3E plug connector with cover () 52-SY Insulation: Red (+) Insulation: lack ( ) 0.3 mm 2 Cable type (TT) 52-SY9220-TT ead wire marking No.1 (+), No.2 ( ) 0.75 mm 2 (ead wire length) Max

14 ody Ported Type Series 52-SY9000 Dimensions 3-position closed centre/exhaust centre/pressure centre plug connector () SY Insulation 5 lack ( ) 4A Insulation Red (+) Manual override x ø3.2 (Mounting holes for manifold) 2 x 1/4", 3/8" {4 (A), 2 () port} (12) (108.5) ø (ead wire length) 201 (125.3) mm 2 ø1.55 (ead wire length) 46 (For E type) 2 x ø4.4 (Mounting holes) x 1/4" {1 (P), 3 (E), 5 (EA) port} 5EA P 3E plug connector with cover () 3 52-SY Insulation: Red (+) Insulation: lack ( ) 0.3 mm 2 Cable type (TT) SY9420-TT ead wire marking No.1 (+), No.2 ( ) 0.75 mm 2 (ead wire length) Max

15 PE ATEX Compliant ase Mounted Type Series 52-SY5000 Dimensions 2-position single plug connector () 52-SY5140 (R) x ø (Mounting holes) M5 x Manual override (External pilot port) Insulation A lack ( ) A 17 M5 x 0.8 (Pilot EXH. port) <For external pilot type> Insulation Red (+) EA P E X mm 2 (ead wire length) ø (For E type) x 1/4" (Piping ports) plug connector with cover () 52-SY5140 (R) --02 Insulation: Red (+) Insulation: lack ( ) 104 (ead wire length) 0.75 mm mm 2 Cable type (TT) 52-SY5140 (R) -TT-02 ead wire marking No.1 (+), No.2 ( ) Max (ead wire length) ø5.9 ø4.1 14

16 ase Mounted Type Series 52-SY5000 Dimensions 2-position double plug connector () 52-SY5240 (R) x ø (Mounting holes) 48 4 M5 x Manual override (External pilot port) Insulation: lack ( ) A A Insulation: Red (+) EA P E X 17 PE M5 x 0.8 (Pilot EXH. port) <For external pilot type> mm 2 (ead wire length) ø (For E type) x 1/4" (Piping ports) plug connector with cover () 52-SY5240 (R) --02 Insulation: Red (+) Insulation: lack ( ) (ead wire length) mm 2 ø (71.7) Cable type (TT) 52-SY5240 (R) -TT-02 ead wire marking No.1 (+), No.2 ( ) (ead wire length) Max mm 2 ø (88.5) 15

17 PE ATEX Compliant ase Mounted Type Series 52-SY5000 Dimensions 3-position closed centre/exhaust centre/pressure centre plug connector () SY5440 (R) x ø (Mounting holes) 48 4 M5 x Insulation: lack ( ) Manual override (External pilot port) A A Insulation: Red (+) EA P E X 17 M5 x 0.8 (Pilot EXH. port) <For external pilot type> mm 2 (ead wire length) ø (For E type) 22 5 x 1/4" (Piping ports) plug connector with cover () 3 52-SY5440 (R) Insulation: Red (+) Insulation: lack ( ) (ead wire length) mm 2 ø Cable type (TT) 3 52-SY5440 (R) -TT-02 5 ead wire marking No.1 (+), No.2 ( ) (ead wire length) Max mm 2 ø

18 ase Mounted Type Series 52-SY7000 Dimensions 2-position single plug connector () 52-SY7140 (R) PE Insulation: lack ( ) Insulation: Red (+) x ø4.3 Manual override (Mounting holes) M5 x 0.8 A (External pilot port) A EA P E X M5 x 0.8 (Pilot EXH. port) <For external pilot type> mm 2 (ead wire length) 26.5 ø (For E type) 5 x 3/8", 1/4" (Piping ports) plug connector with cover () SY7140 (R) -- Insulation: Red (+) Insulation: lack ( ) (ead wire length) 0.3 mm 2 ø Cable type (TT) 02 Max SY7140 (R) -TT- ead wire marking No.1 (+), No.2 ( ) (ead wire length) 0.75 mm 2 39 ø5.9 17

19 PE ATEX Compliant ase Mounted Type Series 52-SY7000 Dimensions 2-position double plug connector () 52-SY7240 (R) Insulation: lack ( ) Insulation: Red (+) Manual override EA A A 61 P E 4 2 x ø4.3 (Mounting holes) M5 x 0.8 (External pilot port) X M5 x 0.8 (Pilot EXH. port) <For external pilot type> mm 2 (ead wire length) 26.5 ø (For E type) 5 x 3/8", 1/4" (Piping ports) plug connector with cover () SY7240 (R) -- Insulation: Red (+) Insulation: lack ( ) (ead wire length) 0.3 mm 2 ø (78.8) Cable type (TT) 52-SY7240 (R) -TT- ead wire marking No.1 (+), No.2 ( ) (ead wire length) Max mm 2 ø (95.6) 18

20 PE ATEX Compliant ase Mounted Type Series 52-SY7000 Dimensions 3-position closed centre/exhaust centre/pressure centre plug connector () SY7440 (R) Insulation lack ( ) Insulation Red (+) Manual override 61 A A EA P E 4 2 x ø4.3 (Mounting holes) M5 x 0.8 (External pilot port) X M5 x 0.8 (Pilot EXH. port) <For external pilot type> mm 2 (ead wire length) 26.5 ø (For E type) 5 x 3/8", 1/4" (Piping ports) plug connector with cover () SY7440 (R) Insulation: Red (+) Insulation: lack ( ) (ead wire length) 0.3 mm 2 ø Cable type (TT) 3 52-SY7440 (R) -TT ead wire marking No.1 (+), No.2 ( ) (ead wire length) Max mm 2 ø

21 ase Mounted Type Series 52-SY9000 Dimensions 2-position single plug connector 52-SY9140 (R) PE Insulation lack ( ) Insulation Red (+) x ø5.4 Manual override (Mounting holes) 1/8" A 5EA A4 1P 2 3E (External pilot port) X /8" (Pilot EXH. port) <For external pilot type> (ead wire length) 0.3 mm 2 ø (For E type) x 3/8", 1/2" (Piping ports) plug connector with cover () SY9140 (R) -- Insulation: Red Insulation: lack (ead wire length) 0.3 mm 2 ø Cable type (TT) 52-SY9140 (R) -TT- ead wire marking No.1 (+), No.2 ( ) Max (ead wire length) 0.75 mm ø5.9 20

22 ase Mounted Type Series 52-SY9000 Dimensions 2-position double plug connector () 52-SY9240 (R) PE Insulation lack ( ) Insulation Red (+) Manual override A 5EA x ø5.4 (Mounting holes) 1/8" (External pilot port) 4A 2 1P 3E X /8" (Pilot EXH. port) <For external pilot type> (ead wire length) plug connector with cover () SY9240 (R) mm 2 Cable type (TT) 52-SY9240 (R) -TT mm mm 2 Insulation: Red (+) Insulation: lack ( ) ead wire marking No.1 (+), No.2 ( ) ø5.9 ø1.55 ø4.1 (ead wire length) (ead wire length) 80.5 (For E type) 5 x 3/8", 1/2" (Piping ports) Max (92) (108.8) 21

23 ase Mounted Type Series 52-SY9000 Dimensions 3-position closed centre/exhaust centre/ pressure centre plug connector () SY9440 (R) PE Insulation lack ( ) Manual override A x ø5.4 (Mounting holes) 1/8" (External pilot port) A Insulation Red (+) 5EA 1P 3E X 27 1/8" (Pilot EXH. port) <For external pilot type> (ead wire length) mm 2 ø (For E type) x 3/8", 1/2" (Piping ports) plug connector with cover () SY9440 (R) Insulation: Red (+) Insulation: lack ( ) (ead wire length) mm 2 ø Cable type (TT) 3 52-SY9440 (R) -TT- 5 ead wire marking No.1 (+), No.2 ( ) (ead wire length) Max mm ø

24 5 Port Solenoid Valve Series 56-VQC1000 Manifold Manifold with M- or T- kit II 3G Ex na II T5 Gc X II 3D Ex tc III C T85 C Dc X IP67 10 C Ta +50 C Special condition X "Protect from Impact" Note) Refer to Serial transmission system on page 30 for the S kit. 56 VV5QC C3 TD0 N... MF / T / S Kit ATEX category 3 Series 56-VQC1000 ase mounted plug-in Stations 01 1 station The minimum or maximum number of stations differs Option None All stations with back pressure check valve D With DIN rail (Rail length: Standard) D With DIN rail (Rail length: Special) K Special wiring specifications (Except double wiring) N With name plate R External pilot depending on the electrical entry. (Refer to Electrical Entry/Cable ength ) C3 C4 C6 M5 CM M M Cylinder port size With ø3.2 One-touch fitting With ø4 One-touch fitting With ø6 One-touch fitting M5 thread Mixed sizes and with port plug Top ported elbow, with ø3.2 One-touch fitting Top ported elbow, with ø4 One-touch fitting Top ported elbow, with ø6 One-touch fitting M5 thread Elbow port, mixture sizes ottom ported elbow, with ø3.2 One-touch fitting ottom ported elbow, with ø4 One-touch fitting ottom ported elbow, with ø6 One-touch fitting M5 thread Elbow for bottom port, mixture sizes COM N COM. M Kit (Circular connector kit) T Kit (Terminal block box kit) Kit designation/electrical entry/cable length S Kit (Serial transmission kit: EX500 gateway type) MD0 MD1 MD2 MD3 26 pins Circular connector kit (26P) without cable 1 to 12 Circular connector kit (26P) with 1.5 m cable stations Circular connector kit (26P) with 3 m cable (Up to 24 TD0 Circular connector kit (26P) with 5 m cable solenoid coils) Terminal block box kit 1 to 10 stations (Up to 20 solenoid coils) The maximum number of stations displayed in parentheses is applied to the special wiring specifications. (Option -K ) The maximum number of stations is determined by the total number of solenoids. (Single solenoid type: 1 point, Double solenoid type: 2 points) Make sure that the total number of solenoids does not exceed the maximum number of stations. Additionally, when combining with option parts, make sure that the maximum number of stations is not exceeded. SI unit: 56-EX500 Note) A separate gateway unit and communication cable are required. SDA2 DeviceNet, PROFIUS DP 1 to 8 stations (Up to 16 solenoid coils) Contact SMC for 56-EX250 with Profibus DP All other specifications are the same as the standard products Series VQC. For details, refer to the WE catalog or est Pneumatics No

25 ase-mounted Type/Plug-in Unit Series 56-VQC1000 Valves ATEX category VQC Series 56-VQC1000 Type of actuation 2-position single 2-position double (Metal) 2-position double (Rubber) 3-position closed centre 3-position exhaust centre 3-position pressure centre 4-position dual 3 port valve (A) 4-position dual 3 port valve () 4-position dual 3 port valve (C) A Note) Note) C Note) Note) For rubber seal type only. Manual override : Non-locking push type (Tool required) : ocking type (Tool required) Manifold Option C: ocking type (Manual) Ground terminal lanking plate assembly Individual SUP spacer Individual EXH spacer SUP block plate EXH block plate EXH block base assembly ack pressure check valve assembly [-] Port plug 2 stations matching fitting assembly Elbow fitting assembly Port plug lanking plug DIN rail mounting bracket [-D] Name plate [-N] 56-VQC1000 VVQ A-1 VVQ1000-P-1-C6 VVQ1000-R-1-C6 VVQ A VVQC A-- VVQ A VVQ A VVQ A-C8 VVQ1000-F-- VVQ A KQ2P- VVQ A(-S) VVQ1000-N- Note) Please refer to standard catalogues for details. Do not use options other than specified in this table. Only these standard parts without "56-" prefix can be used. D: Slide locking type (Manual) Coil voltage 24 VDC 5 Function Standard type (1W) External pilot R Note) Note) Not available for dual 3 port. Seal type 0 Metal seal 1 Rubber seal Note) ''56-'' solenoid valve should be installed in ''56-VV5QC11'' manifold. Power consumption when starting is 1W, when maintaining 0.35W. ''56-VQC'' solenoid valve has no polarity" 24

26 5 Port Solenoid Valve Series 56-VQC2000 Manifolds Manifold with M- or T- kit II 3G Ex na II T5 Gc X II 3D Ex tc III C T85 C Dc X IP67 10 C Ta +50 C Special condition X "Protect from Impact" Note) Refer to Serial transmission system on page 30 for the S kit. 56 VV5QC C4 TD0 N MF / T / S Kit ATEX category 3 Series 56-VQC2000 ase-mounted Plug-in 01 1 station Stations... Options None All stations with back pressure check valve D With DIN rail (rail length: standard) D With DIN rail (rail length: special) K Special wiring specifications (except for double wiring) N With name plate R External pilot T ranched P and R ports on U side The minimum or maximum number of stations differs depending on the electrical entry (refer to Electrical entry/cable length ). C4 C6 C8 CM M M Cylinder port size Note) A separate gateway unit and communication cable are With ø4 One-touch fitting With ø6 One-touch fitting With ø8 One-touch fitting Mixed sizes and with port plug Top ported elbow With ø4 One-touch fitting Top ported elbow With ø6 One-touch fitting Top ported elbow With ø8 One-touch fitting Elbow port, mixture sizes ottom ported elbow With ø4 One-touch fitting ottom ported elbow With ø6 One-touch fitting ottom ported elbow With ø8 One-touch fitting Elbow for bottom port, mixture sizes COM. N COM. M Kit (Multiple connector kit) T Kit (Terminal block box kit) Kit designation/electrical entry/cable length S Kit (Serial transmission kit: EX500 gateway type) 26 pins SI unit: 56-EX500 MD0 MD1 MD2 MD3 Multiple connector kit (26P) without cable 1 to 12 Multiple connector kit (26P) with 1.5 m cable stations Multiple connector kit (26P) with 3 m cable (Up to 24 TD0 Multiple connector kit (26P) with 5 m cable solenoid coils) Terminal block box kit 1 to 10 stations (Up to 20 solenoid coils) The maximum number of stations displayed in parentheses is applied to the special wiring specifications. (Option -K ) The maximum number of stations is determined by the total number of solenoids. (Single solenoid type: 1 point, Double solenoid type: 2 points) Make sure that the total number of solenoids does not exceed the maximum number of stations. Additionally, when combining with option parts, make sure that the maximum number of stations is not exceeded. required. SDA2 DeviceNet, PROFIUS DP 1 to 8 stations (Up to 16 solenoid coils) Contact SMC for 56-EX250 with Profibus DP. All other specifications are the same as the standard products Series VQC. For details, refer to the WE catalog or est Pneumatics No

27 ase-mounted Type/Plug-in Unit Series 56-VQC2000 Valves ATEX category VQC Series 56-VQC2000 Type of actuation 2-position single 2-position double (Metal) 2-position double (Rubber) 3-position closed centre 3-position exhaust centre 3-position pressure centre 4-position dual 3-port valve (A) 4-position dual 3-port valve () 4-position dual 3-port valve (C) A Note) Note) C Note) Note) For rubber seal type only. Manual override : Non-locking push type (Tool required) ø4.2 : ocking type (Tool required) ø4.2 Manifold Options C: ocking type (Manual) 11 mm Name lanking plate assembly Individual SUP spacer Individual EXH spacer SUP block plate EXH block plate EXH block base assembly 56-VQC2000 VVQ A-1 VVQ2000-P-1-C8 VVQ2000-R-1-C8 VVQ A VVQ A ack pressure check valve assembly [-] VVQ A Port plug VVQ A Dual flow fitting assembly VVQ A-C10 Elbow fitting assembly VVQ2000-F-- Port plug VVQ A lanking plug KQ2P- DIN rail mounting bracket [-D] VVQ A (-S) Name plate [-N] VVQ2000-N- Notes) : Please refer to standard catalogues for details. Do not use options other than specified in this table. Only these standard parts without "56-" prefix can be used. Function Standard type (1W) External pilot D: Slide locking type (Manual) ø2 Coil voltage 5 24 VDC R Note) Note) Not available for dual 3 port. OFF ON Seal type 0 Metal seal 1 Rubber seal Note) ''56-'' solenoid valve should be installed in ''56-VV5QC21'' manifold. Power consumption when starting is 1 W, when maintaining 0.35 W. "56-VQC" solenoid valve has no polarity. 26

28 5 Port Solenoid Valve Series 56-VQC4000 Manifolds Manifold with M- or T- kit II 3G Ex na II T5 Gc X II 3D Ex tc III C T85 C Dc X IP67 10 C Ta +50 C Special condition X "Protect from Impact" Note) Refer to Serial transmission system on page 30 for the S kit. 56 VV5QC TD0 N MF / T / S Kit ATEX category 3 Series 56-VQC4000 ase-mounted Plug-in Options None Special wiring specifications K (except for double wiring) N With name plate (T kit only) 01 1 station Stations The maximum number of stations differs depending on the electrical entry (refer to Electrical entry/cable length ). C8 C10 C12 CM Cylinder port size With ø8 One-touch fitting With ø10 One-touch fitting With ø12 One-touch fitting Mixed sizes 1/4 thread 3/8 thread ottom port 1/4 COM. N COM. M Kit (Multiple connector kit) Thread type F N T Rc G NPT NPTF T Kit (Terminal block box kit) Kit designation/electrical entry/cable length S Kit (Serial transmission kit: EX500 gateway type) MD0 MD1 MD2 MD3 26 pins Multiple connector kit (26P) without cable 1 to 12 Multiple connector kit (26P) with 1.5 m cable stations Multiple connector kit (26P) with 3 m cable (Up to 24 Multiple connector kit (26P) with 5 m cable solenoid coils) TD0 Terminal block box kit 1 to 10 stations (Up to 20 solenoid coils) The maximum number of stations displayed in parentheses is applied to the special wiring specifications. (Option -K ) The maximum number of stations is determined by the total number of solenoids. (Single solenoid type: 1 point, Double solenoid type: 2 points) Make sure that the total number of solenoids does not exceed the maximum number of stations. Additionally, when combining with option parts, make sure that the maximum number of stations is not exceeded. SI unit: 56-EX500 Note) A separate gateway unit and communication cable are required. SDA2 DeviceNet, PROFIUS DP 1 to 8 stations (Up to 16 solenoid coils) Contact SMC for 56-EX250 with Profibus DP. All other specifications are the same as the standard products Series VQC. For details, refer to the WE catalog or est Pneumatics No

29 ase-mounted Type/Plug-in Unit Series 56-VQC Valves VQC ATEX category 3 Series 56-VQC4000 Manual override : Non-locking push type (Tool required) Type of actuation 2-position single 2-position double (Metal) 2-position double (Rubber) 3-position closed centre 3-position exhaust centre 3-position pressure centre 3-position perfect : ocking type (Tool required) Manifold Options Name lanking plate assembly Individual SUP spacer Individual EXH spacer SUP block plate EXH block plate EXH block base assembly ack pressure check valve assembly [-] Port plug Dual flow fitting assembly Elbow fitting assembly Port plug lanking plug DIN rail mounting bracket [-D] Name plate [-N] 56-VQC4000 VVQ A-1 VVQ4000-P-1- VVQ4000-R-1- VVQ A VVQ A KQ2P- Notes) : Please refer to standard catalogues for details. Do not use options other than specified in this table. Only these standard parts without "56-" prefix can be used. Coil voltage 5 24 VDC Function Standard type (1W) External pilot R Note) Note) Not available for dual 3 port. Seal type 0 Metal seal 1 Rubber seal Note) ''56-'' solenoid valve should be installed in ''56-VV5QC41'' manifold. Power consumption when starting is 1 W, when maintaining 0.35 W. "56-VQC" solenoid valve has no polarity. 28

30 For Input/Output Series 56-EX250 SI Units Input block SI unit ATEX category 3 56 EX250 S PR1 X42 Communication Protocol PR1 PROFIUS DP SI Unit Specifications II 3G Ex na II T4 X 5 C Ta 45 C II 3D Ex td A22 IP67 T66 C X Input lock Protocol Model Communication speed Number of outputs Output type Output Connected load specifications Input specifications Power supply Current supply Number of inputs Input block Power supply Current supply Internal current consumption (Unit) Operating temperature/humidity range Withstand voltage Insulation resistance Enclosure Weight 56-EX250-SPR1-X42 PROFIUS DP-V0 (9.6/19.2/45.45/93.75/187.5/500 kbps), (1.5/3/6/12 Mbps) Max. 32 points Source/PNP (Negative common) Solenoid valve with protection circuit for 24 VDC and 1.5 W or less surge voltage (made by SMC) 24 VDC + 10%/ 5% Max. 2.0 A Max. 32 points 56-EX250-IE2-X43 24 VDC ± 20% Max. 1.0 A 100 ma or less +5 to +45 C at 35% to 85% RH (without condensation) 500 VAC for 1 min. between external terminal and FG 10 MΩ or more (500 VDC) between external terminal and FG IP g ATEX category 3 56 EX250 IE 2 X43 lock type 2 M12 connector, 4 inputs Input lock Specifications II 3G Ex na II T4 X 5 C Ta 45 C II 3D Ex td A22 IP67 T77 C X Model Applicable sensor Number of inputs Rated voltage Rated input current Display Connector on the input device side Sensor supply current Operating temperature/humidity range Withstand voltage Insulation resistance Enclosure Weight 56-EX250-IE2-X43 Source type (PNP output) Sink type (NPN output)/(selected using a switch) 4 inputs 24 VDC Approx. 8 ma Green ED is ON (when SI unit power supply is ON). Yellow ED is ON (when input signal is ON). M12 connector (4 pins, plug or 5 pins, plug) Max. 30 ma/sensor 10 to +50 C at 35% to 85% RH (without condensation) 500 VAC for 1 min. between external terminal and FG 10 MΩ or more (500 VDC) between external terminal and FG IP67 90 g All other specifications are the same as the standard products Series EX250. For details, refer to the WE catalog or est Pneumatics No

31 Decentralized Serial Wiring (GW System, 4 ranches) Series 56-EX500 Gateway (GW) Unit Gateway (GW) Unit ATEX category 3 56 EX500 G PR1A Communication Protocol PR1A PROFIUS DP DN1-X8 DeviceNet TM II 3G Ex na II T4 X 5 C Ta 45 C II 3D Ex td A22 IP65 T57 C X (56-EX500-GPR1A) II 3G Ex na II T4 X 5 C Ta 45 C II 3D Ex td A22 IP65 T53 C X (56-EX500-GDN1-X8) Gateway (GW) Unit Specifications Model Applicable PC/Communication protocol Communication speed Rated voltage Power supply voltage range Current consumption Inputs/outputs points Input/output branches Input supply current Output supply current ranch cable length Operating temperature/humidity range Withstand voltage Insulation resistance Enclosure Weight 56-EX500-GDN1-X8 DeviceNet TM 125/250/500 Kbps (9.6/19.2/45.45/93.75/187.5/500 Kbps),(1.5/3/6/12 Mbps) 24 VDC Input and control unit power supply: 24 VDC ±10% Solenoid valve power supply: 24 VDC +10%/ 5% 200 ma or less (single GW unit) Maximum 64 inputs/64 outputs 4 branches (16 inputs/16 outputs per branch) Max. 2.8 A (Max. 0.7 A per branch) Max. 3.0 A (Max A per branch) 470 g 56-EX500-GPR1A PROFIUS DP-V0 Maximum 32 inputs/64 outputs 4 branches (8 inputs/16 outputs per branch) 5 m or less between connected devices (Total 10 m or less per branch) +5 to +45 C at 35% to 85% RH (without condensation) 1000 VAC for 1 minute between terminals and housing IP65 Max. 1.4 A (Max A per branch) 2 MΩ or more (500 VDC) between terminals and housing All other specifications are the same as the standard products Series EX500. For details, refer to the WE catalog or est Pneumatics No

32 Decentralized Serial Wiring (GW System, 4 ranches) Series 56-EX500 SI Units ATEX category 3 56 EX500 II 3G Ex na II T5 X 5 C Ta 45 C II 3D Ex td A22 IP67 T52 C X S001 Applicable solenoid valve: Series SV SI Unit Specifications (56-EX500-S001) Model Internal current consumption Number of outputs Output type Connection block Output Connection block stations Connection block supply current Enclosure Operating temperature range Environment Operating humidity range Withstand voltage Insulation resistance Standards Weight Accessory: Waterproof cap (for M12 connector socket) 56-EX500-S ma or less 16 outputs Sink/NPN (Positive common) Solenoid valve (Single, double) Relay output module (1 output, 2 outputs) Double solenoid valve, relay output module (2 outputs): Max. 8 stations Single solenoid valve, relay output module (1 output): Max. 16 stations Max A IP67 Operating: 5 to 45 C Stored: 25 to 70 C (with no freezing and condensation) Operating, Stored: 35 to 85%RH (with no condensation) 1000 VAC for 1 minute between terminals and housing 2 MΩ or more (500 VDC) between terminals and housing CE marking, U (CSA) 115 g EX500-AWTS (1 pc.) SI Units 56 EX500 Q ATEX category 3 Applicable solenoid valve: Series SY/VQC/S0700 II 3G Ex na II T5 X 5 C Ta 45 C II 3D Ex td A22 IP67 T54 C X SI unit COM. 0 Sink/NPN (Positive common) 1 Source/PNP (Negative common) SI unit type 1 For without EX9 output block 2 For EX9 output block mounting SI Unit Specifications (56-EX500-Q0) Model 56-EX500-Q EX500-Q101 Internal current consumption Number of outputs 100 ma or less 16 outputs Output type Sink/NPN (Positive common) Source/PNP (Negative common) Output Connection block Positive common compatible solenoid valve (single, double) Negative common compatible solenoid valve (single, double) Connection block stations Double solenoid valve: Max. 8 stations Single solenoid valve: Max. 16 stations Environment Connection block supply current Enclosure Operating temperature range Operating humidity range Withstand voltage Insulation resistance Max A IP67 Operating: 5 to 45 C Stored: 25 to 70 C (with no freezing and condensation) Operating, Stored: 35 to 85%RH (with no condensation) 1000 VAC for 1 minute between terminals and housing 2 MΩ or more (500 VDC) between terminals and housing Standards Weight CE marking, U (CSA) 105 g Accessory: Waterproof cap (for M12 connector socket) EX500-AWTS (1 pc.) 31

33 Decentralized Serial Wiring (GW System, 4 ranches) Series 56-EX500 How to order Input manifold EEX500 I1 E 4 Input unit specification Connector type E M8 connector T M12 connector Stations M M8 and M12 mixed 1 1 station 4 4 stations When ordering an input block manifold, enter the Input manifold part no. + Input block part no. together. The input block, end block and DIN rail are included in the input manifold. Refer to. Example) M8 and M12 on a single manifold Input block Input unit side 56-EX500-IE1 (2 sets) Input block 56-EX500-IE3 (2 sets) Input block II 3G Ex na II T5 X 5 C Ta 45 C II 3D Ex td A22 IP65 T60 C X ATEX category 3 56 EX500 IE 1 56-EX500-I1 lock type 1 M8 connector, 2 inputs, PNP specification 2 M8 connector, 2 inputs, NPN specification 3 M12 connector, 2 inputs, PNP specification 4 M12 connector, 2 inputs, NPN specification 5 8-point integrated type, M8 connector, PNP specifications 6 8-point integrated type, M8 connector, NPN specifications EEX500-I1-M4 1 set 56-EX500-IE1 2 sets 56-EX500-IE3 2 sets End block side II 3G Ex na II T5 X 5 C Ta 45 C II 3D Ex td A22 IP65 T60 C X II 3G Ex na II T5 X 5 C Ta 45 C II 3D Ex td A22 IP65 T66 C X (Input block 56-EX500-IE1 to 4) (Input block 56-EX500-IE5 to 6) Input unit specification Input block specifications Model 56-EX500-l1 Model 56-EX500-IE1,3,5 56-EX500-IE2,4,6 Connection block The EX500 series input block (mixed combination is possible) Max. 8 points (56-EX500-GPR1A) Number of inputs Max. 16 points(56-ex500-gdn1-x8) lock supply voltage 24 VDC Max A (56-EX500-GPR1A) lock supply current Max. 0.7 A (56-EX500-GDN1-X8) Current consumption 100 ma or less Operating temperature range Operating: 5 to 45 C Stored: 25 to 70 C (with no freezing and condensation) Operating humidity range Operating, Stored: 35 to 85%RH (with no condensation) Withstand voltage 1000 VAC for 1 minute between terminals and housing Insulation resistance 2 MΩ or more (500 VDC) between terminals and housing Enclosure IP65 Weight Note) 100 g (Input unit + end block) Note) Not including the DIN rail weight. Input type PNP sensor input NPN sensor input Sensor connector IE1/2/5/6: M8 connector (3 pins), IE3/4: M12 connector (4 pins) Number of inputs IE1/2/3/4: 2 inputs, IE5/6: 8 inputs Rated voltage 24 VDC Sensor supply current Max. 30 ma/sensor Operating temperature range Operating: 5 to 45 C Stored: 25 to 70 C (with no freezing and condensation) Operating humidity range Operating, Stored: 35 to 85%RH (with no condensation) Withstand voltage Insulation resistance 1000 VAC for 1 minute between terminals and housing 2 MΩ or more (500 VDC) between terminals and housing Enclosure IP65 Weight IE1/2: 20 g, IE3/4: 40 g, IE5/6: 55 g 32

34 Fieldbus System Series 56-EX600 SI Unit 56-EX600 S EN1 Protocol Symbol Description PR1A PROFIUS DP EN1 EtherNet/IP X10 II 3G Ex na IIC T4 Gc X -10 C Ta 50 C II 3D Ex tc IIIC T82 C Dc X IP67 II 3G Ex na IIC T4 Gc X -10 C Ta 50 C II 3D Ex tc IIIC T77 C Dc X IP67 (56-EX600-SPR1A-X10) (56-EX600-SEN1-X10) Digital Input Unit 56-EX600 Symbol P N DX Input type Description PNP NPN P D X10 Number of Inputs, Open circuit detection, and Connector Symbol Number of inputs Open circuit detection Connector C 8 inputs No M8 connector (3 pins) 8 pcs. D 16 inputs No M12 connector (5 pins) 8 pcs. II 3G Ex na IIC T4 Gc X -10 C Ta 50 C II 3D Ex tc IIIC T82 C Dc X IP67 II 3G Ex na IIC T4 Gc X -10 C Ta 50 C II 3D Ex tc IIIC T86 C Dc X IP67 (56-EX600-DXmC-X10) (56-EX600-DXmD-X10) End Plate 56-EX600 ED 2 Power connector Symbol Connector 2 M12 (5 pins) X10 Mounting method Symbol Description Without DIN rail mounting bracket 2 With DIN rail mounting bracket II 3G Ex na IIC T4 Gc X -10 C Ta 50 C II 3D Ex tc IIIC T72 C Dc X IP67 A 32-1

35 Fieldbus System Series EX600 SI Unit Specifications All Units Common Specifications Environmental resistance Operating temperature range 10 to 50 C Storage temperature range 20 to 60 C Operating humidity range 35 to 85% RH (No dew condensation) Withstand voltage 500 VAC for 1 minute between external terminals and FE Insulation resistance 500 VDC, 10 MW or more between external terminals and FE SI Unit Communication Model Protocol Device type Communication speed Configuration file Occupation area (Number of inputs/outputs) Terminating resistor Internal current consumption (Power supply for Control/Input) Output type Number of outputs oad Power supply Fail safe Protection Enclosure Weight Output 56-EX600-SPR1A-X10 PROFIUS DP (DP-V0) PROFIUS DP Slave 9.6/19.2/45.45/93.75/187.5/500 kbps 1.5/3/6/12 Mbps GSD file Max. (512 inputs/512 outputs) Internally implemented 80 ma or less Source/PNP (Negative common) 32 outputs (8/16/24/32 outputs selectable) Solenoid valve with surge voltage suppressor 24 VDC, 1.5 W or less (SMC) 24 VDC, 2 A HOD/CEAR/Forced power ON Short-circuit protection IP67 (Manifold assembly) 300 g SI Unit Model 56-EX600-SEN1-X10 Number of communication ports 1 port Protocol EtherNet/IP (Conformance version: Composite 6) Communication speed 10/100 Mbps Communication method Full duplex/half duplex Configuration file EDS file Occupation area (Number of inputs/outputs) Max. (512 inputs/512 outputs) Communication IP address setting range Device information Internal current consumption (Power supply for Control/Input) Output type Number of outputs Output oad Power supply Fail safe Protection Enclosure Weight SI Unit switch settings: or 1.1 to 254 Through DHCP server: Optional address Vendor ID: 7 (SMC Corporation) Device type: 12 (Communication Adapter) Product code: ma or less Source/PNP (Negative common) 32 outputs (8/16/24/32 outputs selectable) Solenoid valve with surge voltage suppressor 24 VDC, 1.5 W or less (SMC) 24 VDC, 2 A HOD/CEAR/Forced power ON Short-circuit protection IP67 (Manifold assembly) 300 g 32-2 A

36 Series EX600 Digital Unit Specifications 56-EX600-DXC-X10 56-EX600-DXD-X10 Digital Input Unit Model 56-EX600-DXPC-X10 56-EX600-DXNC-X10 56-EX600-DXPD-X10 56-EX600-DXND-X10 Input type PNP NPN PNP NPN Input Input connector M8 (3-pin) socket Note 2) M12 (5-pin) socket Note 1) Number of inputs 8 inputs (1 input/connector) 16 inputs (2 inputs/connector) Supplied voltage Max. supplied current Protection Input current (at 24 VDC) ON voltage OFF voltage 0.25 A/Connector 2 A/Unit 24 VDC Short-circuit protection 9 ma or less 0.5 A/Connector 2 A/Unit 17 V or more (At NPN input, between the pin for input terminal and supplied voltage of +24 V) (At PNP input, between the pin for input terminal and supplied voltage of 0 V) 5 V or less (At NPN input, between the pin for input terminal and supplied voltage of +24 V) (At PNP input, between the pin for input terminal and supplied voltage of 0 V) Current consumption 55 ma or less 70 ma or less Enclosure IP67 (Manifold assembly) Weight 275 g 340 g Note 1) M12 (4-pin) connector can be connected. Note 2) When connecting the M8 plug connector, the tightening torque must be 0.2 N m ±10%. If tightened with an excessive tightening torque, this may cause the connector thread of the Unit to break. A 32-3

37 Fieldbus System Series EX600 End Plate Specifications End Plate Power specifications Model Power connector Power supply (for Control/Input) Power supply (for Output) Enclosure Weight 56-EX600-ED2--X10 M12 (5-pin) plug 24 VDC ±10%, Class 2, 2 A 24 VDC +10/ 5%, Class 2, 2 A IP67 (Manifold assembly) 170 g 56-EX600-ED2--X A

38 Air cylinder Standard: Double Acting, Single Rod Series 55-C76 ø32, ø40 II 2GDc 90 C (T5) Ta 10 C to 40 C 110 C (T4) Ta 40 C to 60 C Without magnet With magnet 55 C76 E 55 CD76 E C XC6A C A XC6A ATEX category 2 uilt-in magnet for auto switch E F Y Mounting Double end Front nose Front nose in line port Except air cushion type. Made to Order XC6A Standard Stainless steel piston rod and rod-end nut Stainless steel piston rod, rod-end nut and mounting nut XC6 XC22 XC85 X2018 Only with rubber cushion type. Fluororubber seals Food grade grease ong stroke Mounting racket Part No. (mm) Mounting bracket Foot (1 pc.) Foot (2 pcs. with mounting nut 1 pc.) Trunnion Clevis Single knuckle joint Double knuckle joint Floating joint Mounting bracket Accessory C76F32A C76F32 C76T32 C76C32 KJ10DA GKM10-20A JA mm mm C76F40A C76F40 C76T40 C76C40 KJ12DA GKM12-24A JA (mm) Auto switch mounting A Rail mounting and mounting Cushion Rubber cushion (Standard) C Air cushion (only E execution) Cylinder stroke Standard stroke 10,25,40,50,80, ,160,200,250,300 X2018 (ong stroke) 301 to 1000 Refer to page 69 for applicable auto switches. Refer to page 36 for dimensions. Specifications (mm) ø32 ø40 Action Fluid Proof pressure Max. operating pressure Min. operating pressure Ambient and fluid temperature ubrication Piston speed Stroke tolerance Cushion Double Acting, Single rod Air 1.5 MPa 1.0 MPa 0.05 MPa 10 to 60 C (No freezing) Not required (Non-lube) 50 to 1000 mm/s mm Rubber cushion, Air cushion Port size G1/8 G1/4 Mounting Double end, Front nose, Front nose in line port 33

39 Air cylinder Standard: Double Acting, Double Rod Series 55-C76W ø32, ø40 II 2GDc 90 C (T5) Ta 10 C to 40 C 110 C (T4) Ta 40 C to 60 C Without magnet 55 C76 WE C XC6A With magnet 55 CD76WE C A XC6A ATEX category 2 uilt-in magnet for auto switch E Mounting Double end type Made to Order Standard Stainless steel piston rod and XC6A rod-end nut Stainless steel piston rod, XC6 rod-end nut and mounting nut XC22 Fluororubber seals XC85 Food grade lubricant X2018 ong stroke Only with rubber cushion type. Mounting racket Part No. Mounting (mm) bracket Foot (1 pc.) Foot (2 pcs. with mounting nut 1 pc.) Trunnion Clevis Single knuckle joint Double knuckle joint Floating joint C76F32A C76F32 C76T32 C76C32 KJ10DA GKM10-20A JA C76F40A C76F40 C76T40 C76C40 KJ12DA GKM12-24A JA Mounting bracket Accessory mm mm Auto switch mounting A Rail mounting and mounting Cushion Rubber cushion (Standard) C Air cushion Cylinder stroke (mm) Standard stroke 10,25,40,50,80,100, ,200,250,300 X2018 (ong stroke) 301 to 500 Refer to page 69 for applicable auto switches. Refer to pages 37 and 38 for dimensions. Specifications (mm) ø32 ø40 Action Fluid Proof pressure Max. operating pressure Min. operating pressure Ambient and fluid temperature ubrication Piston speed Stroke tolerance Cushion Port size Mounting Double Acting, Double Rod Air 1.5 MPa 1.0 MPa 0.05 MPa 10 to 60 C (no freezing) Not required (Non-lube) 50 to 1000 mm/s mm Rubber cushion, Air cushion G1/8 G1/4 Double end 34

40 Air cylinder Non-rotating Type: Double Acting, Single Rod Series 55-C76K ø32, ø40 II 2GDc 90 C (T5) Ta 10 C to 40 C 110 C (T4) Ta 40 C to 60 C Without magnet With magnet 55 C76K E XC6A 55 CD76K E A XC6A ATEX category 2 uilt-in magnet for auto switch E F Y Mounting Double end Front nose Front nose in line port Made to Order Standard Stainless steel piston rod and XC6A rod-end nut Stainless steel piston rod, XC6 rod-end nut and mounting nut X2018 ong stroke Mounting racket Part No. Mounting (mm) bracket Foot (1 pc.) Foot (2 pcs. with mounting nut 1 pc.) Trunnion Clevis Single knuckle joint Double knuckle joint Floating joint C76F32A C76F32 C76T32 C76C32 KJ10DA GKM10-20A JA C76F40A C76F40 C76T40 C76C40 KJ12DA GKM12-24A JA Mounting bracket Accessory mm mm Auto switch mounting A Rail mounting and mounting Cylinder stroke (mm) Standard stroke 32 10,25,40,50,80, ,160,200,250,300 X2018 (ong stroke) 301 to 1000 Refer to page 69 for applicable auto switches. Refer to page 36 for dimensions. Specifications (mm) ø32 ø40 Action Fluid Proof pressure Max. operating pressure Min. operating pressure Ambient and fluid temperature ubrication Piston speed Stroke tolerance Cushion Double Acting, Single Rod Air 1.5 MPa 1.0 MPa 0.05 MPa 10 to 60 C (No freezing) Not required (Non-lube) 50 to 1000 mm/s mm Rubber cushion Port size G1/8 G1/4 Non-rotating accuracy ±0.5 ±0.5 Mounting Double end, Front nose, Front nose in line port 35

41 Air cylinder Standard: Double Acting, Single Rod Series 55-C76 Dimensions Double Acting, Single Rod A Rod foot, Head foot (Flange): C76F32, C76F40 A W T NH TF UR XS AU S + Stroke TR 12-øA X + Stroke AO US Rod trunnion, Head trunnion: C76T32, C76T40 øtde8 øtde8 TZ TZ X Port N Port XC + Stroke Rod clevis, Head clevis: C76C32, C75C40 X CZ XC + Stroke CW T CH T CE CO CR 4-øA CT 4-øA CE CO CR CG CU CG ore size A 7 9 AO AU Rod foot, Head foot (Flange) S T 4 5 NH TF TR UR US W X Rod trunnion, Head trunnion XS N TDe8 TZ X XC A 7 9 CE CG CH Rod clevis, Head clevis CO 4 3 CR CT CU CW CZ T 4 5 X (mm) XC

42 Air cylinder Standard: Double Acting, Double Rod Series 55-C76 Dimensions Double Acting, Double Rod Rubber cushion: C76WE Stroke Without magnet, uilt-in magnet SW E K X WH G øc 2-øEh8 EE EE G X + Stroke WH + Stroke E K HR 8 45 økv ød øc N AM KW FA 1.5 N 4-TC 1.5 N FA AM KK TW øtd H9 H S + Stroke ZZ + 2 x Stroke H + Stroke Rail mounting (A) and mounting () Without magnet Air cushion: C76WE Stroke C uilt-in magnet Cushion valve WA WA W HR 8 45 N N Rail mounting (A) and mounting () Without magnet (mm) AM E M30 x 1.5 M38 x 1.5 C ( ): In the case of air cushion D Eh EE FA G G 1/8 30 G 1/ H HR K KK M10 x 1.5 M12 x 1.75 KV W KW 7 8 N N 17(19) (25) 42.5 S SW TC TDH9 M8 x M10 x TW WH X ZZ WA

43 Air cylinder Standard: Double Acting, Double Rod Series 55-C76 Dimensions Double Acting, Double Rod A Rod foot, Head foot (Flange): C76F32, C76F40 A W T NH TF UR XS AU S + Stroke X + Stroke AO XT + Stroke TR US 12-øA Rod trunnion, Head trunnion: C76T32, C76T40 ø TDe8 TZ Port X XC + Stroke N Clevis type: C76C32, C75C40 X XC + Stroke CZ CW T CH CE CO CR 4-øA CT CG CU ore size A 7 9 AO AU Rod foot, Head foot (Flange) S T 4 5 NH TF TR UR US W X XS Rod trunnion, Head trunnion TZ X XC XT N TDe A 7 9 CE CG CH CO 4 3 CR Clevis CT CU CW CZ T 4 5 (mm) X XC

44 Series 55-C76 Accessories Single knuckle joint (DIN648 compliant) Double knuckle joint (DIN7151 compliant) D 1 3 D øf α α D7 D345 3 G E øj C D6 2 H Model KJ10DA KJ12DA Thread D3 M10 x 1.5 M12 x 1.75 DH H D D (mm) α Model GKM10-20A GKM12-24A Thread E M10 x 1.5 M12 x D F G C J (mm) Floating joint/series JA JA25/40 M M U U ød F G E P H A (mm) Model JA JA M Nominal thread dia. Pitch A D E F G H Maximum screwed depth P 9 13 Allowable eccentricity U Max. operating tension and compression power (kn)

45 ISO Cylinder [ISO/6432] Standard: Double Acting, Single Rod Series 55-C85 ø8, ø10, ø12, ø16, ø20, ø25 II 2GDc 90 C (T5) Ta 10 C to 40 C 110 C (T4) Ta 40 C to 60 C Without magnet 55 C85 N C XC6A With magnet 55 CD85 N C A XC6A ATEX category 2 uilt-in magnet for auto switch N E F Y Mounting asic (integrated clevis) Double end Front nose Front nose in line port Air cushion type is available for N type only. Made to Order Standard Stainless steel piston XC6A rod and rod-end nut Stainless steel piston rod, XC6 rod-end nut and mounting nut XC22 Fluororubber seals X2018 ong stroke Specifications (mm) Action Fluid Proof pressure Max. operating pressure Double Acting, Single Rod Air 1.5 MPa 1.0 MPa Min. operating pressure 0.1 MPa 0.08 MPa 0.05 MPa Ambient and fluid temperature ubrication Piston speed 10 to 60 C (No freezing) Not required (Non-lube) Air cushion: 50 to 1000 mm/s, Rubber cushion: 50 to 750 mm/s Stroke tolerance mm mm Cushion Rubber cushion Rubber cushion, Air cushion Port size M5X0.8 G1/8 Mounting Integrated clevis, Double end, Front nose, Front nose in line port Mounting racket Part No. Mounting bracket Mounting bracket Accessory (mm) Foot (1 pc.) Foot (2 pcs. with mounting nut 1 pc.) Flange Trunnion Clevis Single knuckle joint Double knuckle joint Floating joint C8510A C8510 C85F10 C85T10 C85C10 KJ4D GKM4-8 JA C8516A C8516 C85F16 C85T16 C85C16 KJ6D GKM6-10 JA C8525A C8525 C85F25 C85T25 C85C25 KJ8D GKM8-16 JA KJ10D GKM10-20 JA (mm) Cushion Rubber cushion (Standard) Air cushion C (Only N execution, bores 10 to 25 mm) Cylinder stroke Standard stroke (mm) 10, 25, 40, 50, 80, , 25, 40, 50, 80, , 160, , 25, 40, 50, 80, , 160, 200, 250, 300 Not available with air cushion. Other strokes available on request. Auto switch mounting type A Rail mounting and mounting Please order auto switches and bands separately. X2018 (ong stroke) 101 to to to to 1000 All other specifications are the same as the standard products Series C85. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. 40

46 ISO Cylinder [ISO/6432] Standard: Double Acting, Double Rod Series 55-C85W ø8, ø10, ø12, ø16, ø20, ø25 II 2GDc 90 C (T5) Ta 10 C to 40 C 110 C (T4) Ta 40 C to 60 C Without magnet 55 C85W E C XC6A With magnet 55 CD85WE C XC6A ATEX category 2 uilt-in magnet for auto switch E Mounting Double end Made to Order Standard Stainless steel piston XC6A rod and rod-end nut Stainless steel piston rod, XC6 rod-end nut and mounting nut XC22 Fluororubber seals X2018 ong stroke Specifications Mounting racket Part No. Mounting bracket Mounting bracket Accessory (mm) Action Fluid Proof pressure Max. operating pressure Min. operating pressure Ambient and fluid temperature ubrication Piston speed Stroke tolerance Cushion Port size Mounting (mm) Foot (1 pc.) Foot (2 pcs. with mounting nut 1 pc.) Flange Trunnion Clevis Single knuckle joint Double knuckle joint Floating joint C8510A C8510 C85F10 C85T10 C85C10 KJ4D GKM4-8 JA Double Acting, Double Rod Air 1.5 MPa 1.0 MPa 0.1 MPa 0.08 MPa 0.05 MPa 10 to 60 C (No freezing) Not required (Non-lube) Air cushion: 50 to 1000 mm/s, Rubber cushion: 50 to 750 mm/s Rubber cushion mm C8516A C8516 C85F16 C85T16 C85C16 KJ6D GKM6-10 JA C8525A C8525 C85F25 C85T25 C85C25 KJ8D GKM8-16 JA mm Rubber cushion, Air cushion M5X0.8 G1/8 Double end KJ10D GKM10-20 JA (mm) Cushion Rubber cushion (Standard) Air cushion C (Only N execution, bores 10 to 25 mm) Cylinder stroke Standard stroke (mm) 10, 25, 40, 50, 80, , 25, 40, 50, 80, , 160, , 25, 40, 50, 80, , 160, 200, 250, 300 Not available with air cushion. Other strokes available on request. Auto switch mounting type A Rail mounting and mounting Please order auto switches and bands separately. X2018 (ong stroke) 301 to 500 All other specifications are the same as the standard products Series C85W. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. 41

47 ISO Cylinder [ISO/6432] Non-rotating Type: Double Acting, Single Rod Series 55-C85K ø8, ø10, ø12, ø16, ø20, ø25 II 2GDc 90 C (T5) Ta 10 C to 40 C 110 C (T4) Ta 40 C to 60 C Without magnet 55 With magnet 55 C85 K N CD85K N XC6A A XC6A ATEX category 2 uilt-in magnet for auto switch N E F Y Mounting asic (integrated clevis) Double end Front nose Front nose in line port Made to Order Standard Stainless steel piston rod XC6A and rod-end nut Stainless steel piston rod, XC6 rod-end nut and mounting nut X2018 ong stroke Specifications (mm) Action Fluid Proof pressure Max. operating pressure Min. operating pressure Ambient and fluid temperature ubrication Piston speed Stroke tolerance Cushion Port size Non-rotating accuracy Mounting Double Acting, Single Rod Air 1.5 MPa 1.0 MPa 0.1 MPa 0.08 MPa 0.05 MPa 10 to 60 C (No freezing) Not required (Non-lube) Rubber cushion: 50 to 750 mm/s mm mm Rubber cushion M5X0.8 G1/8 ±1.5 ±1 ±0.7 Integrated clevis, Double end, Front nose, Front nose in line port (mm) Cylinder stroke Standard stroke (mm) 10, 25, 40, 50, 80, , 25, 40, 50, 80, , 160, , 25, 40, 50, 80, , 160, 200, 250, 300 Other strokes available on request. Auto switch mounting type A Rail mounting and mounting Please order auto switches and bands separately. X2018 (ong stroke) 101 to to to to 1000 Mounting racket Part No. Mounting bracket Mounting bracket Accessory (mm) Foot (1 pc.) Foot (2 pcs. with mounting nut 1 pc.) Flange Trunnion Clevis Single knuckle joint Double knuckle joint Floating joint C8510A C8510 C85F10 C85T10 C85C10 KJ4D GKM4-8 JA C8516A C8516 C85F16 C85T16 C85C16 KJ6D GKM6-10 JA C8525A C8525 C85F25 C85T25 C85C25 KJ8D GKM8-16 JA KJ10D GKM10-20 JA All other specifications are the same as the standard products Series C85K. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. 42

48 Without magnet With magnet ATEX category 2 F G C D T Specifications 55 ø160, ø200, ø250 C95S 55 C95SD uilt-in magnet for auto switch Mounting asic/without bracket Axial foot Rod side flange Head side flange Single clevis Double clevis Centre trunnion ATEX Compliant ISO Cylinder Standard: Double Acting, Single Rod Series 55-C95 II 2GDc 95 C (T5) Ta 10 C to 40 C 115 C (T4) Ta 40 C to 60 C mm mm mm (mm) ø160 ø200 ø250 Action Fluid Proof pressure Max. operating pressure Min. operating pressure Ambient and fluid temperature ubrication Piston speed Double Acting, Single Rod Air 1.5 MPa 1.0 MPa 0.05 MPa 10 to 60 C (No freezing) Not required (Non-lube) 50 to 500 mm/s Stroke tolerance Cushion Up to 250: , 251 to 1000: , 1001 to 1500: to 2000: , 2001 to 2400: oth ends (Air cushion) Port size G3/4 G3/4 G1 Mounting asic, Axial foot, Rod side flange, Head side flange, Single clevis, Double clevis, Centre trunnion 100 XC6 100 XC6 Made to Order Standard XA Change of rod end shape Stainless steel XC6 piston rod and rod-end nut XC14 Change of trunnion bracket mounting position (Rod side) Simple specials part no. except for XC14A or. Cylinder stroke Maximum Stroke (mm) Standard XC Please consult with SMC for longer strokes. XC Class 2 Pressure Vessel Series C95 can not be used as the Class 2 Pressure Vessels. If the stroke exceeds the following values, the cylinder with such stroke can not be installed or used in Japan. (mm) Cylinder stroke (mm) All other specifications are the same as the standard products Series C95. Refer to page 69 for applicable auto switches. Mounting racket, Mounting Accessories Description ø160 ø200 ø250 F, G C D Foot Flange Single clevis Double clevis 5160 F5160 C5160 D F5200 C5200 D F5250 C5250 D5250 GKM KJ Rod clevis (2) Piston rod (3) ball joint GKM35-54 KJ36D GKM40-84 KJ42D Note 1) Accessories for each mounting bracket are as follows. Foot, Flange, Single clevis: Mounting bolts Double clevis: Mounting bolts, Clevis pin Note 2) GKM according to ISO 8140 (Except GKM35-54) Note 3) KJ according to ISO

49 ISO Cylinder Standard: Double Acting, Double Rod Series 55-C95W ø160, ø200, ø250 II 2GDc 95 C (T5) Ta 10 C to 40 C 115 C (T4) Ta 40 C to 60 C Without magnet With magnet ATEX category 2 Specifications C95S C95SD uilt-in magnet for auto switch F T Mounting asic/without bracket Axial foot Rod side flange Centre trunnion mm mm mm W XC6 100 W XC6 Made to Order Standard XA Change of rod end shape Stainless steel piston rod and XC6 rod-end nut (ø32 to ø100) XC14 Change of trunnion bracket mounting position Simple specials part no. except for XC14A or. Cylinder stroke Maximum Stroke (mm) Standard XC Please consult with SMC for longer strokes. XC (mm) ø160 ø200 ø250 Action Fluid Proof pressure Max. operating pressure Min. operating pressure Ambient and fluid temperature ubrication Piston speed Double Acting, Double Rod Air 1.5 MPa 1.0 MPa 0.05 MPa 10 to 60 C (No freezing) Not required (Non-lube) 50 to 500 mm/s Stroke tolerance Cushion Up to 250: , 251 to 1000: , 1001 to 1500: to 2000: , 2001 to 2400: oth ends (Air cushion) Port size G3/4 G3/4 G1 Mounting asic, Axial foot, Rod side flange, Centre trunnion Class 2 Pressure Vessel Series C95 can not be used as the Class 2 Pressure Vessels. If the stroke exceeds the following values, the cylinder with such stroke can not be installed or used in Japan. (mm) Cylinder stroke (mm) All other specifications are the same as the standard products Series C95W. Refer to page 69 for applicable auto switches. Mounting racket, Mounting Accessories Description ø160 ø200 ø250 F GKM Foot Flange Rod clevis (2) F5160 F5200 GKM35-54 Piston rod KJ (3) KJ36D ball joint Note 1) Mounting bolts are shipped together for foot style and flange style. Note 2) GKM according to ISO 8140 (Except GKM35-54) Note 3) KJ according to ISO F5250 GKM40-84 KJ42D 44

50 ISO Cylinder Standard: Double Acting, Single Rod Series 55-C96 ø32, ø40, ø50, ø63, ø80, ø100 Without magnet II 2GDc 85 C (T5) Ta 20 C to 40 C 105 C (T4) Ta 40 C to 60 C uilt-in magnet 85 C (T5) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C For the ø125, refer to page Without magnet 55 With magnet 55 C96S C C96SD C XC68 XC68 ATEX category 2 uilt-in magnet for auto switch F G C D T Mounting asic/without bracket Axial foot Rod side flange Head side flange Single clevis Double clevis Centre trunnion mm mm mm mm mm mm Made to Order Standard XA Change of rod end shape XC4 With heavy duty scraper (ø32 to ø100) Tie-rod, cushion valve, tie-rod nut, XC7 etc. made of stainless steel XC14 Change of trunnion bracket mounting position XC22 Fluororubber seals Made of Stainless Steel XC65 (Combination of XC7 and XC68) With chrome plated stainless steel XC68 piston rod and stainless steel nut Simple specials part no. except for XC14A or. Cylinder stroke (mm) (mm) Standard stroke (mm) 32 25, 50, 80, 100, 125, 160, , 320, 400, , 50, 80, 100, 125, 160, , 320, 400, , 50, 80, 100, 125, 160, , 320, 400, 500, , 50, 80, 100, 125, 160, , 320, 400, 500, , 50, 80, 100, 125, 160, , 320, 400, 500, 600, 700, , 50, 80, 100, 125, 160, , 320, 400, 500, 600, 700, 800 Intermediate strokes are available. Please consult with SMC for longer strokes. Standard max. stroke XC65, XC68 Max. stroke All other specifications are the same as the standard products Series C96. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. 45 a

51 ISO Cylinder Standard: Double Acting, Single Rod Series 55-C96 ø125 Without magnet II 2GDc 85 C (T5) Ta 20 C to 40 C 105 C (T4) Ta 40 C to 60 C uilt-in magnet 85 C (T5) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C For the ø32, ø40, ø50, ø63, ø80, and ø100, refer to page 45. Without magnet 55 C96S XC68 With magnet 55 C96SD XC68 ATEX category 2 uilt-in magnet for auto switch F G C D T Mounting asic/without bracket Axial foot Rod side flange Head side flange Single clevis Double clevis Centre trunnion mm Made to Order Standard XA Change of rod end shape Tie-rod, cushion valve, tie-rod nut, XC7 etc. made of stainless steel XC14 Change of trunnion bracket mounting position XC18 NPT ports XC22 Fluororubber seals With chrome plated stainless steel XC68 piston rod and stainless steel nut Simple specials part no. except for XC14A or. Cylinder stroke (mm) (mm) Standard max. stroke XC68 Max. stroke Intermediate strokes are available. Please consult with SMC for longer strokes. ø125 are produced upon receipt of order. All other specifications are the same as the standard products Series C96. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. a 45-1

52 ISO Cylinder Standard: Double Acting, Double Rod Series 55-C96W ø32, ø40, ø50, ø63, ø80, ø100 Without magnet II 2GDc 85 C (T5) Ta 20 C to 40 C 105 C (T4) Ta 40 C to 60 C uilt-in magnet 85 C (T5) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C For the ø125, refer to page Without magnet 55 With magnet 55 C96S CW C96SD CW XC68 XC68 ATEX category 2 uilt-in magnet for auto switch F T Mounting asic/without bracket Axial foot Rod side flange Centre trunnion Made to Order Standard XA Change of rod end shape XC4 With heavy duty scraper (ø32 to ø100) Tie-rod, cushion valve, tie-rod nut, XC7 etc. made of stainless steel XC14 Change of trunnion bracket mounting position XC22 Fluororubber seals Made of Stainless Steel XC65 (Combination of XC7 and XC68) With chrome plated stainless steel XC68 piston rod and stainless steel nut Simple specials part no. except for XC14A or mm mm mm mm mm mm Rod W Double rod Cylinder stroke (mm) Standard stroke (mm) (mm) 25, 50, 80, 100, 125, 160, , 320, 400, , 50, 80, 100, 125, 160, , 320, 400, , 50, 80, 100, 125, 160, , 320, 400, 500, , 50, 80, 100, 125, 160, , 320, 400, 500, , 50, 80, 100, 125, 160, , 320, 400, 500, 600, 700, , 50, 80, 100, 125, 160, , 320, 400, 500, 600, 700, 800 Intermediate strokes are available. Please consult with SMC for longer strokes. Max. stroke All other specifications are the same as the standard products Series C96W. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. 46 a

53 ISO Cylinder Standard: Double Acting, Double Rod Series 55-C96W ø125 Without magnet II 2GDc 85 C (T5) Ta 20 C to 40 C 105 C (T4) Ta 40 C to 60 C uilt-in magnet 85 C (T5) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C For the ø32, ø40, ø50, ø63, ø80, and ø100, refer to page 46. Without magnet 55 C96S W XC68 With magnet 55 C96SD W XC68 ATEX category 2 uilt-in magnet for auto switch F T Mounting asic/without bracket Axial foot Rod side flange Centre trunnion Made to Order Standard XA Change of rod end shape Tie-rod, cushion valve, tie-rod nut, XC7 etc. made of stainless steel XC14 Change of trunnion bracket mounting position XC18 NPT ports XC22 Fluororubber seals With chrome plated stainless steel XC68 piston rod and stainless steel nut Simple specials part no. except for XC14A or mm Rod W Double rod Cylinder stroke (mm) (mm) 125 Max. stroke 1000 Intermediate strokes are available. Please consult with SMC for longer strokes. ø125 are produced upon receipt of order. All other specifications are the same as the standard products Series C96W. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. a 46-1

54 ISO Cylinder Non-rotating Type: Double Acting, Single Rod Series 55-C96K ø32, ø40, ø50, ø63, ø80, ø100 Without magnet II 2GDc 85 C (T5) Ta 20 C to 40 C 105 C (T4) Ta 40 C to 60 C uilt-in magnet 85 C (T5) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C Without magnet 55 With magnet 55 C96K C C96KD C ATEX category 2 uilt-in magnet for auto switch F G C D T Mounting asic/without bracket Axial foot Rod side flange Head side flange Single clevis Double clevis Centre trunnion Cylinder stroke (mm) (mm) Maximum stroke (mm) mm mm mm mm mm mm All other specifications are the same as the standard products Series C96. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. 47 a

55 ISO Cylinder Non-rotating Type: Double Acting, Double Rod Series 55-C96KW ø32, ø40, ø50, ø63, ø80, ø100 Without magnet II 2GDc 85 C (T5) Ta 20 C to 40 C 105 C (T4) Ta 40 C to 60 C uilt-in magnet 85 C (T5) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C Without magnet 55 With magnet ATEX category 2 55 C96K CW C96KD CW Rod W Double rod uilt-in magnet for auto switch F T Mounting asic/without bracket Axial foot Rod side flange Centre trunnion mm mm mm mm mm mm Cylinder stroke (mm) (mm) Maximum stroke (mm) All other specifications are the same as the standard products Series C96W. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. 48 a

56 ISO Cylinder Smooth cylinder: Double Acting, Single Rod Series 55-C96Y ø32, ø40, ø50, ø63, ø80, ø100, ø125 Without magnet II 2GDc 85 C (T5) Ta 20 C to 40 C 105 C (T4) Ta 40 C to 60 C uilt-in magnet 85 C (T5) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C Without magnet 55 With magnet 55 C96Y C96YD ATEX category 2 uilt-in magnet for auto switch F G C D T Mounting asic/without bracket Axial foot Rod side flange Head side flange Single clevis Double clevis Centre trunnion Cylinder stroke (mm) (mm) Maximum stroke (mm) mm mm mm mm mm mm mm All other specifications are the same as the standard products Series C96. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. 49

57 ISO Cylinder Standard: Double Acting, Single Rod Series 55-CP96 ø32, ø40, ø50, ø63, ø80, ø100 Without magnet II 2GDc 85 C (T5) Ta 20 C to 40 C 105 C (T4) Ta 40 C to 60 C uilt-in magnet 85 C (T5) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C For the ø125, refer to page Without magnet 55 With magnet 55 CP96S C XC68 CP96SD C XC68 ATEX category 2 uilt-in magnet for auto switch F G C D Mounting asic/without bracket Axial foot Rod side flange Head side flange Single clevis Double clevis Made to Order Standard XA Change of rod end shape XC4 With heavy duty scraper (ø32 to ø100) Tie-rod, cushion valve, tie-rod nut, XC7 etc. made of stainless steel XC22 Fluororubber seals Made of Stainless Steel XC65 (Combination of XC7 and XC68) With chrome plated stainless steel XC68 piston rod and stainless steel nut mm mm mm mm mm mm Standard stroke (mm) (mm) 25, 50, 80, 100, 125, 160, , 320, 400, , 50, 80, 100, 125, 160, , 320, 400, , 50, 80, 100, 125, 160, , 320, 400, 500, , 50, 80, 100, 125, 160, , 320, 400, 500, , 50, 80, 100, 125, 160, , 320, 400, 500, 600, 700, , 50, 80, 100, 125, 160, , 320, 400, 500, 600, 700, 800 Intermediate strokes are available. Please consult with SMC for longer strokes. Cylinder stroke (mm) Max. stroke XC65, XC68 Max. stroke All other specifications are the same as the standard products Series CP96. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. 50 a

58 ISO Cylinder Standard: Double Acting, Single Rod Series 55-CP96 ø125 Without magnet II 2GDc 85 C (T5) Ta 20 C to 40 C 105 C (T4) Ta 40 C to 60 C uilt-in magnet 85 C (T5) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C For the ø32, ø40, ø50, ø63, ø80, and ø100, refer to page 50. Without magnet 55 With magnet 55 CP96S CP96SD XC XC68 ATEX category 2 uilt-in magnet for auto switch F G C D Mounting asic/without bracket Axial foot Rod side flange Head side flange Single clevis Double clevis Made to Order Standard XA Change of rod end shape Tie-rod, cushion valve, tie-rod nut, XC7 etc. made of stainless steel XC18 NPT ports XC22 Fluororubber seals With chrome plated stainless steel XC68 piston rod and stainless steel nut mm Cylinder stroke (mm) Max. stroke (mm) XC68 Max. stroke Intermediate strokes are available. Please consult with SMC for longer strokes. ø125 are produced upon receipt of order. All other specifications are the same as the standard products Series CP96. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. a 50-1

59 ISO Cylinder Standard: Double Acting, Double Rod Series 55-CP96W ø32, ø40, ø50, ø63, ø80, ø100 Without magnet II 2GDc 85 C (T5) Ta 20 C to 40 C 105 C (T4) Ta 40 C to 60 C uilt-in magnet 85 C (T5) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C For the ø125, refer to page Without magnet 55 With magnet 55 CP96S CW CP96SD CW XC68 XC68 ATEX category 2 uilt-in magnet for auto switch F Mounting asic/without bracket Axial foot Rod side flange Made to Order Standard XA Change of rod end shape XC4 With heavy duty scraper (ø32 to ø100) Tie-rod, cushion valve, tie-rod nut, XC7 etc. made of stainless steel XC22 Fluororubber seals Made of Stainless Steel XC65 (Combination of XC7 and XC68) With chrome plated stainless steel XC68 piston rod and stainless steel nut mm mm mm mm mm mm Rod W Double rod Cylinder stroke (mm) (mm) Standard stroke (mm) 32 25, 50, 80, 100, 125, 160, , 320, 400, , 50, 80, 100, 125, 160, , 320, 400, , 50, 80, 100, 125, 160, , 320, 400, 500, , 50, 80, 100, 125, 160, , 320, 400, 500, , 50, 80, 100, 125, 160, , 320, 400, 500, 600, 700, , 50, 80, 100, 125, 160, , 320, 400, 500, 600, 700, 800 Intermediate strokes are available. Please consult with SMC for longer strokes Max. stroke All other specifications are the same as the standard products Series CP96W. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. 51 a

60 ISO Cylinder Standard: Double Acting, Double Rod Series 55-CP96W ø125 Without magnet II 2GDc 85 C (T5) Ta 20 C to 40 C 105 C (T4) Ta 40 C to 60 C uilt-in magnet 85 C (T5) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C For the ø32, ø40, ø50, ø63, ø80, and ø100, refer to page 51. Without magnet 55 With magnet 55 CP96S CP96SD W XC W XC68 ATEX category 2 uilt-in magnet for auto switch F Mounting asic/without bracket Axial foot Rod side flange Made to Order Standard XA Change of rod end shape Tie-rod, cushion valve, tie-rod nut, XC7 etc. made of stainless steel XC18 NPT ports XC22 Fluororubber seals With chrome plated stainless steel XC68 piston rod and stainless steel nut mm Rod W Double rod Cylinder stroke (mm) 125 (mm) Max. stroke 1000 Intermediate strokes are available. Please consult with SMC for longer strokes. ø125 are produced upon receipt of order. All other specifications are the same as the standard products Series CP96W. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. a 51-1

61 ISO Cylinder Non-rotating Type: Double Acting, Single Rod Series 55-CP96K ø32, ø40, ø50, ø63, ø80, ø100 Without magnet II 2GDc 85 C (T5) Ta 20 C to 40 C 105 C (T4) Ta 40 C to 60 C uilt-in magnet 85 C (T5) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C Without magnet 55 With magnet 55 CP96K CP96KD C C ATEX category 2 uilt-in magnet for auto switch F G C D Mounting asic/without bracket Axial foot Rod side flange Head side flange Single clevis Double clevis Cylinder stroke (mm) Maximum stroke (mm) (mm) mm mm mm mm mm mm All other specifications are the same as the standard products Series CP96. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. 52 a

62 ISO Cylinder Non-rotating Type: Double Acting, Double Rod Series 55-CP96KW ø32, ø40, ø50, ø63, ø80, ø100 Without magnet II 2GDc 85 C (T5) Ta 20 C to 40 C 105 C (T4) Ta 40 C to 60 C uilt-in magnet 85 C (T5) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C Without magnet 55 With magnet 55 CP96K CP96KD CW CW ATEX category 2 uilt-in magnet for auto switch Rod W Double rod F Mounting asic/without bracket Axial foot Rod side flange Cylinder stroke (mm) Maximum stroke (mm) (mm) mm mm mm mm mm mm All other specifications are the same as the standard products Series CP96W. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. 53 a

63 ISO Standards Compact Cylinder/Standard type: Double acting, Single rod Series 55-C55 ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 II 2GDc 85 C(T6) Ta -10 C to 40 C 105 C(T4) Ta 40 C to 60 C Without magnet 55 C With magnet 55 CD ATEX category 2 uilt-in magnet for auto switch F G C Mounting Through-hole/oth ends tapped common (Standard) Foot Rod side flange Head side flange Single clevis mm mm mm mm mm mm mm mm ody option Standard (Rod end female thread) M Rod end male thread Cylinder stroke (mm) (mm) Standard stroke (mm) 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, to , 125, , 15, 20, 25, 30, 35, 40, 45, 50, 60, 80 80, , 125 All other specifications are the same as the standard products Series C55. For details, refer to the WE catalog or ISO Cylinder (CAT.P-E10-2). Refer to page 69 for applicable auto switches. 54

64 Air Cylinder/Standard type: Double acting, Single rod Series 55-CG1 ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 II 2GDc 95 C (T5) Ta 10 C to 40 C 115 C (T4) Ta 40 C to 60 C Without magnet With magnet 55 CG1 N CDG1 N XC85 XC85 ATEX category 2 uilt-in magnet for auto switch F G U T D Mounting asic Axial foot Rod side flange Head side flange Rod side trunnion Head side trunnion Clevis Not available for ø80 or ø100. Note) Mounting brackets are shipped together, (but not assembled). N A Type Rubber cushion Air cushion 20 mm 25 mm 32 mm 40 mm mm mm mm mm Port thread type Rubber cushion TN TF Rc NPT M5 x 0.8 G Air cushion M5 x 0.8 Rc M5 x 0.8 TN NPT M5 x 0.8 TF G ø20 to ø100 ø20 to ø100 ø20, ø25 ø32 to ø100 ø20, ø25 ø32 to ø100 ø20, ø25 ø32 to ø100 ø20, ø25 ø32 to ø100 Made to Order Standard XC85 Food grade grease XC10 Note 1) Dual stroke cylinder/double rod XC11 Note 1) 2) Dual stroke cylinders/single rod Note 1) for XC10, and XC11 are different from the above. Refer to in est Pneumatics No. 2. Note 2) Not available for rubber cushion type. Note 3) XC10 and XC11 are not applicable to XC85. (mm) , Standard stroke Note 1) (mm) 25, 50, 75, 100, 125, 150, , 50, 75, 100, 125, 150, 200, 250, 300 Cylinder stroke (mm) ong stroke Note 2) (mm) 201 to to to to to to to 1500 Note 1) Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) ong stroke is compatible with the axial foot and rod side flange types. When other mounting brackets are used or the long stroke exceeds the limit, the allowable maximum stroke length is determined using the stroke selection table (est Pneumatics No. 2). All other specifications are the same as the standard products Series CG1. For details, refer to the WE catalog or est Pneumatics No. 2. Refer to page 69 for applicable auto switches. 55

65 Air Cylinder/Standard type: Double acting, Double rod Series 55-CG1W ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 II 2GDc 95 C (T5) Ta 10 C to 40 C 115 C (T4) Ta 40 C to 60 C Without magnet With magnet 55 CG1 W N CDG1W N XC85 XC85 ATEX category 2 uilt-in magnet for auto switch Made to Order Standard XC85 Food grade grease Double Acting/Double Rod F U Mounting asic Axial foot Flange Centre trunnion Not available for bore size ø80 and ø100. Note) Mounting brackets are shipped together, (but not assembled). N A Type Rubber cushion Air cushion 20 mm 25 mm 32 mm 40 mm mm mm mm mm Port thread type Rubber cushion TN TF Rc NPT M5 x 0.8 G Air cushion M5 x 0.8 Rc M5 x 0.8 TN NPT M5 x 0.8 TF G ø20 to ø100 ø20 to ø100 ø20, ø25 ø32 to ø100 ø20, ø25 ø32 to ø100 ø20, ø25 ø32 to ø100 ø20, ø25 ø32 to ø100 Cylinder stroke (mm) (mm) Standard stroke Note 1) (mm) ong stroke (mm) 20 25, 50, 75, 100, 125, 150, to to to , 50, 75, 100, 125, 150, to , , to to to 1500 Note 1) Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) ong stroke is compatible with the axial foot and rod side flange types. When other mounting brackets are used or the long stroke exceeds the limit, the allowable maximum stroke length is determined using the stroke selection table (est Pneumatics No. 2). All other specifications are the same as the standard products Series CG1W. For details, refer to the WE catalog or est Pneumatics No. 2. Refer to page 69 for applicable auto switches. 56

66 ATEX category 2 ATEX Compliant Air Cylinder/Standard type: Non-lube Series 55-CS1 Non-lube type: ø125, ø140, ø160, ø180, ø200, ø250, ø300 II 2GDc 95 C (T5) Ta 0 C to 40 C 115 C (T4) Ta 40 C to 60 C 55 CS1 N F G C D T Mounting asic Foot Rod side flange Head side flange Single clevis Double clevis Centre trunnion Cushion N R H Cushion Without cushion With cushion in rod side With cushion in head side With cushion in both sides If specifying more than one symbol, indicate them alphabetically. Tubing material Symbol F (mm) 125, , to , Tubing material Aluminum Steel Steel Stroke range (mm) 1000 or less 1200 or less 1001 or more 1201 or more All strokes 1000 or less 1200 or less Non-lube type mm mm mm mm mm mm mm N Type Non-lube type Cylinder stroke (mm) Tubing material Aluminum Steel Mounting asic, bracket asic, Head side flange, Head side flange, Single clevis, Double clevis, Single clevis, Foot Centre trunnion, Foot, ore Double clevis, Rod side flange Rod side flange size Centre trunnion or less 1000 or less 1600 or less or less 1200 or less 1600 or less or less 1200 or less 1600 or less or less 2000 or less or less 2000 or less or less 2400 or less or less 2400 or less Class 2 Pressure Vessel The cylinder with a stroke exceeding the level shown below that is applicable to the Class 2 Pressure Vessel Act cannot be installed or used in Japan. (mm) Cylinder stroke (mm) All other specifications are the same as the standard products Series CS1. For details, refer to the WE catalog or est Pneumatics No. 2. Refer to page 69 for applicable auto switches. 57

67 Air cylinder Series 55-CDS1 ø125, ø140, ø160, ø180, ø200 II 2GDc 95 C (T5) Ta 0 C to 40 C 115 C (T4) Ta 40 C to 60 C With magnet 55 CDS1 N ATEX category 2 uilt-in magnet for auto switch F G C D T Mounting asic Foot Rod side flange Head side flange Single clevis Double clevis Centre trunnion N Type Non-lube type Non-lube type mm mm mm mm mm Cushion N R Cushion H Without cushion With cushion in rod side With cushion in head side With cushion in both sides If specifying more than one symbol, indicate them alphabetically. (mm) 125, asic, Head side flange, Single clevis, Double clevis, Centre trunnion 1000 or less 1200 or less 1200 or less 1200 or less Cylinder stroke (mm) Maximum Stroke Foot, Rod side flange 1400 or less 1400 or less 1500 or less 1200 or less Class 2 Pressure Vessel The cylinder with a stroke exceeding the level shown below that is applicable to the Class 2 Pressure Vessel Act cannot be installed or used in Japan. (mm) Cylinder stroke (mm) All other specifications are the same as the standard products Series CS1. For details, refer to the WE catalog or est Pneumatics No. 2. Refer to page 69 for applicable auto switches. 58

68 Air Cylinder: Double Rod Type Series 55-CS1W Non-lube type: ø125, ø140, ø160, ø180, ø200, ø250, ø300 II 2GDc 95 C (T5) Ta 0 C to 40 C 115 C (T4) Ta 40 C to 60 C Without magnet 55 CS1 W N With magnet 55 CDS1W N ATEX category 2 uilt-in magnet for auto switch Double rod Cushion Cushion N R H Without cushion With cushion in rod side With cushion in head side With cushion in both sides If specifying more than one symbol, indicate them alphabetically. Symbol F F T Mounting asic Foot Rod side flange Centre trunnion (mm) 125, , , Tubing material Tubing material Aluminum Steel Steel Type N Non-lube type mm mm mm mm mm mm 300 mm It is not available with auto switch. Non-lube type Tubing material Mounting ore bracket size (mm) 125, , 300 Cylinder stroke (mm) Aluminum Steel Without magnet With magnet Without magnet asic, Foot, Rod side flange, Centre trunnion 1000 or less 1000 or less 1000 or less 1200 or less 1200 or less 1200 or less 1200 or less 1200 or less 1200 or less 1200 or less 1200 or less Class 2 Pressure Vessel The cylinder with a stroke exceeding the level shown below that is applicable to the Class 2 Pressure Vessel Act cannot be installed or used in Japan. (mm) Cylinder stroke (mm) All other specifications are the same as the standard products Series CS1W. For details, refer to the WE catalog or est Pneumatics No. 2. Refer to page 69 for applicable auto switches. 59

69 Compact Cylinder/Standard type: Double acting, Single rod Series 55-CQ2 ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 II 2GDc 85 C (T6) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C Without magnet ø12 to ø25 55 CQ D Without magnet ø32 to ø CQ D Z With magnet 55 CDQ D Z ATEX category 2 With magnet (uilt-in magnet) Made to Order Standard XC85 With food grade grease Mounting bracket A F G D Through-hole (Standard) oth ends tapped Foot Rod side flange Head side flange Double clevis Mounting brackets are shipped together, (but not assembled). Cylinder mounting bolts are not included mm mm mm mm mm mm mm mm mm mm ody option Standard (Rod end female thread) C With rubber bumper M Rod end male thread Combination of body options (CM) is available. Action D Double acting Cylinder stroke (mm) 12, 16 20, 25 32, to 100 Auto switch mounting groove Z ø12 to ø25 ø32 to ø100 2 surfaces 4 surfaces Standard stroke 5, 10, 15, 20, 25, 30 5, 10, 15, 20, 25, 30, 35, 40, 45, 50 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 75, , 15, 20, 25, 30, 35, 40, 45, 50, 75, 100 Note) For intermediate strokes, refer to the standard products Series CQ2. Port thread type M thread ø12 to ø25 Rc ø32 to ø100 TF G For cylinders without magnet, M threads are compatible only with ø32-5 mm stroke. All other specifications are the same as the standard products Series CQ2. For details, refer to the WE catalog or est Pneumatics No. 2. Refer to page 69 for applicable auto switches. 60

70 Compact Cylinder/Standard type: Double Acting, Double Rod Series 55-CQ2W ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 II 2GDc 85 C (T6) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C Without magnet ø12 to ø25 Without magnet ø32 to ø100 With magnet ATEX category With magnet (uilt-in magnet) CQ2W CQ2W CDQ2W Mounting bracket A F Through-hole (Standard) oth ends tapped Foot Flange Mounting brackets are shipped together, (but not assembled). Cylinder mounting bolts are not included mm mm mm mm mm mm mm mm mm mm 30 D 30 D 30 D Z Z Action D Double acting Cylinder stroke (mm) 12, 16 20, 25 32, to 100 Auto switch mounting groove Z Made to Order Standard XC85 With food grade grease ø12 to ø25 ø32 to ø100 2 surfaces 4 surfaces ody option Standard (Rod end female thread) C With rubber bumper M Rod end male thread Combination of body options (CM) is available. Standard stroke 5, 10, 15, 20, 25, 30 5, 10, 15, 20, 25, 30, 35, 40, 45, 50 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 75, , 15, 20, 25, 30, 35, 40, 45, 50, 75, 100 Port thread type M thread ø12 to ø25 Rc ø32 to ø100 TF G For cylinders without magnet, M threads are compatible only with ø32-5 mm stroke. All other specifications are the same as the standard products Series CQ2. For details, refer to the WE catalog or est Pneumatics No. 2. Refer to page 69 for applicable auto switches. 61

71 Compact Cylinder: ong Stroke/Double Acting, Single Rod Series 55-CQ2 ø32, ø40, ø50, ø63, ø80, ø100 II 2GDc 85 C (T6) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C Without magnet 55 CQ2 A DC Z With magnet 55 CDQ2 A DC Z ATEX category 2 uilt-in magnet for auto switch Made to Order Standard XC85 With food grade grease A F G D Mounting bracket oth ends tapped Foot Rod side flange Head side flange Double clevis Mounting brackets are shipped together, (but not assembled). TF mm 40 mm 50 mm 63 mm 80 mm 100 mm Port thread type Rc G Action D Double acting ody option Standard (Rod end female thread) M Rod end male thread Cushion C Rubber cushion Auto switch mounting groove Z 4 surfaces Cylinder stroke (mm) Standard stroke 32, 40, 50 63, 80, , 150, 175, 200, 250, 300 All other specifications are the same as the standard products Series CQ2. For details, refer to the WE catalog or est Pneumatics No. 2. Refer to page 69 for applicable auto switches. 62

72 Compact Cylinder: arge ore Size/Double Acting, Single Rod Series 55-CQ2 ø125, ø140, ø160, ø180, ø200 II 2GDc 85 C (T6) Ta 10 C to 40 C 105 C (T4) Ta 40 C to 60 C Without magnet 55 CQ DC Z With magnet 55 CDQ DC Z ATEX category 2 uilt-in magnet for auto switch Made to Order Standard XC85 With food grade grease Mounting bracket Standard (Through-hole/oth ends tapped common) Cylinder mounting bolts are not included mm 140 mm 160 mm 180 mm 200 mm ody option Standard (Rod end female thread) M Rod end male thread Cushion C Rubber cushion Auto switch mounting groove Z 4 surfaces TF Port thread type Rc G Action D Double acting Cylinder stroke (mm) 125, 140, , 200 Standard stroke 10, 20, 30, 40, 50, 75, , 150, 175, 200, 250, 300 All other specifications are the same as the standard products Series CQ2. For details, refer to the WE catalog or est Pneumatics No. 2. Refer to page 69 for applicable auto switches. 63

73 Dual Rod Cylinder/asic Type Series 55-CXS ø6, ø10, ø15, ø20, ø25, ø32 II 2GDc 65 C (T6) Ta 10 C to 40 C 85 C (T6) Ta 40 C to 60 C Port thread type Symbol Type M thread Rc1/8 TF G1/8 55 CXS M ø6 to ø20 ø25, ø32 ATEX category 2 M earing Slide bearing all bushing bearing Made to Order Standard X11 ong stroke type /Standard stroke (mm) Standard stroke (mm) 6 10, 20, 30, 40, 50 10, 15, 20, 25, 30, 35, 40, 45, 10 50, 60, 70, 75 15, 20 25, 32 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 75, 80, 90, 100 All other specifications are the same as the standard products Series CXS. For details, refer to the WE catalog or est Pneumatics No. 3. Refer to page 69 for applicable auto switches. 64

74 Dual Rod Cylinder/Double Rod Type Series 55-CXSW ø6, ø10, ø15, ø20, ø25, ø32 II 2GDc 65 C (T6) Ta 10 C to 40 C 85 C (T6) Ta 40 C to 60 C Port thread type Symbol Type M thread ø6 to ø20 Rc1/8 ø25, ø32 TF G1/8 55 CXS W ATEX category 2 Double rod type Made to Order Standard X11 ong stroke type M earing Slide bearing all bushing bearing /Stroke (mm) Standard stroke 6 10, 20, 30, 40, 50 10, 15 10, 20, 30, 40, 50 10, 20, 30, 40, 50, 20, 25, 32 75, 100 All other specifications are the same as the standard products Series CXS. For details, refer to the WE catalog or est Pneumatics No. 3. Refer to page 69 for applicable auto switches. 65

75 asic 55 ATEX Compliant Mechanically Jointed Rodless Cylinder/asic Type Series 55-MY1 ø10, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 II 2Gc 75 C (T6) Ta 5 C to 40 C 95 C (T5) Ta 40 C to 60 C MY ATEX category 2 Symbol TN TF asic mm mm mm mm mm mm mm mm mm mm Port thread type ø10, ø16, ø20 Type M thread Rc NPT G ø25,ø32, ø40, ø50, ø63, ø80, ø100 Cylinder stroke (mm) (mm) 10, 16 20, 25, 32, 40 50, 63, 80, 100 Made to Order Standard type X11 ong stroke type Standard stroke (mm) 100, 200, 300, 400, 500, , 800, 900, 1000, , 1600, 1800, 2000 Maximum stroke (mm) Strokes are manufacturable in 1 mm increments, up to the maximum stroke. However, when exceeding a 2000 mm stroke, specify -X11 at the end of the model number. With strokes of 49 mm or less, the air cushion capacity may decrease and it may not be possible to mount multiple auto switches. Piping Standard G Centralized piping type Note) For ø10, only G is available. All other specifications are the same as the standard products Series MY1. For details, refer to the WE catalog or est Pneumatics No. 2. Refer to page 69 for applicable auto switches. 66

76 Mechanically Jointed Rodless Cylinder/Slide earing Guide Type Series 55-MY1M ø16, ø20, ø25, ø32, ø40, ø50, ø63 II 2Gc 75 C (T6) Ta 5 C to 40 C 95 C (T5) Ta 40 C to 60 C Slide bearing guide type 55 MY1M 20 G 300 ATEX category 2 Slide bearing guide type Made to Order Standard type X11 ong stroke type mm mm mm mm mm mm mm Symbol TN TF Port thread type Type M thread Rc NPT G ø16, ø20 ø25, ø32, ø40, ø50, ø63 G Piping Standard Centralized piping type (mm) 16 20, 25, 32 40, 50, 63 Standard stroke (mm) 100, 200, 300, 400, 500, 600, , 900, 1000, 1200, 1400, , 2000 Cylinder stroke (mm) Maximum stroke (mm) Strokes are manufacturable in 1 mm increments, up to the maximum stroke. However, when exceeding a 2000 mm stroke, specify -X11 at the end of the model number. With strokes of 49 mm or less, the air cushion capacity may decrease and it may not be possible to mount multiple auto switches. All other specifications are the same as the standard products Series MY1M. For details, refer to the WE catalog or est Pneumatics No. 2. Refer to page 69 for applicable auto switches. 67

77 Mechanically Jointed Rodless Cylinder/inear Guide Type Series 55-MY1H ø10, ø16, ø20, ø25, ø32, ø40 II 2Gc 75 C (T6) Ta 5 C to 40 C 95 C (T5) Ta 40 C to 60 C inear guide type 55 MY1H ATEX category 2 inear guide type mm mm mm mm mm mm Port thread type Symbol Type M thread ø10, ø16, ø20 Rc TN TF NPT G ø25, ø32, ø40 G Piping Standard Centralized piping type Note) For ø10, only G is available. Made to Order Standard type X10 Intermediate stroke (using exclusive body) X11 ong stroke type Cylinder stroke (mm) (mm) Standard stroke (mm) 10, 16, 20 50, 100, 150, 200, 250, , 32, , 400, 450, 500, 550, 600 Maximum stroke (mm) Strokes are manufacturable from 50 mm in 1 mm increments, up to the maximum stroke. However, add -X10 to the end of the part number for nonstandard strokes from 51 to 599. Also when exceeding a 600 mm stroke, specify -X11 at the end of the model number. (Except ø10) All other specifications are the same as the standard products Series MY1H. For details, refer to the WE catalog or est Pneumatics No. 2. Refer to page 69 for applicable auto switches. inear guide type 55 MY1H X1985 ATEX category 2 inear guide type Symbol TN TF mm mm mm Port thread type Type Rc NPT ø25 to ø40 G Piping Standard G Centralized piping type Rust proof guide Cylinder stroke (mm) (mm) Standard stroke (mm) 25 50, 100, 150, 200, 250, 300, 350, , 450, 500, 550, 600, X1985 type can only be manufactured with the strokes listed in table. 68

78 Switch type D-M9-588 Model 55- C76 Auto Switch Applicable Cylinder ist 55- C85 Note 1) 55- C C CP CQ2(Z) CXS/W 55- C CG1 55- CS1 (20 to 63) (125 to 200) 55- MY1 (Except 50) 55- MY1M 55- MY1H 56- CR1 56- CR2 56- CRU2 55- CRQ2 D-M9V-588 Note 2) (125 to 200) (Except 50) D-M9W-588 Note 1) (20 to 63) (125 to 200) (Except 50) D-M9WV-588 Note 2) (125 to 200) (Except 50) D-H7A2-588 Note 3) (20 to 63) D-F7P-588 Note 4) (12 to 160) D-F7PV-588 Note 4) (12 to 160) D-F5P-588 (160 to 250) (125 to 200) D-Y7P-588 (160 to 200) (125 to 200) (25 to 100) (25 to 63) (25 to 40) D-Y7PV-588 (160 to 200) (125 to 200) (25 to 100) (25 to 63) (25 to 40) D-S7P-588 (50 to 100) (20 to 40) (20 to 40) D-S9P-588 (10, 15) (10, 15) D-S9PV-588 (10, 15) (10, 15) D-F6P-588 D-C D-C Note 3) (20 to 63) D-A D-A Note 4) (12 to 160) D-A73H-588 D-A80H-588 Note 4) (12 to 160) D-A D-A (160 to 250) (125 to 200) D-A D-A (16 to 25) (20 to 63) (125 to 200) (10 to 20) (16, 20) D-A90V-588 D-A93V-588 Note 5) (125 to 200) (10 to 20) (16, 20) D-90A-588 D-93A-588 (125 to 200) (10, 15) (10, 15) D-Z D-Z (160 to 200) (125 to 200) (25 to 100) (25 to 63) (25 to 40) D-E73A-588 D-E80A-588 D-R D-R (50 to 100) (20 to 40) (20 to 40) ( ): Cylinder size Note 1) 55-C85 and mounting all sizes, and Rail mounting for 8 to 16 only. Note 2) 55-C85 and mounting only. Note 3) 55-C85 Rail mounting only. Note 4) 55-C85 Rail mounting only. Note 5) 55-C85 Rail mounting only, for 16 to 25 only. 69

79 Solid State Switch/Direct Mounting D-M9N(V) D-M9P(V) D-M9(V)-588 II 3G Ex na II T5 X 10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Auto Switch Specifications PC: Programmable ogic Controller D-M9/D-M9V (With indicator light) Auto switch part no. D-M9N D-M9NV D-M9P D-M9PV D-M9 D-M9V Electrical entry direction In-line Perpendicular In-line Perpendicular In-line Perpendicular Wiring type 3-wire 2-wire Output type NPN PNP Applicable load Power supply Current consumption IC circuit, Relay, PC 5/12/24 VDC (4.5 to 28 V) 10 ma or less 24 VDC relay, PC oad voltage 28 VDC or less 24 VDC (10 to 28V) oad current 40 ma or less 2.5 to 40 ma Internal voltage drop eakage current 0.8 V or less at 10 ma (2 V or less at 40 ma) 100 µa or less at 24 VDC 4 V or less 0.8 ma or less Indicator light Standard Red ED illuminates when turned ON. CE marking This category 3 type auto switch can only be used in zones 2 and 22. Oilproof Heavy-duty ead Wire Specifications Auto switch model D-M9N D-M9P D-M9 Sheath Outside diameter [mm] 2.7 x 3.2 (ellipse) Insulator Conductor Number of cores Cross section [mm 2 ] 3 cores (rown/lue/lack) cores (rown/lue) Outside diameter [mm] Strand diameter [mm] ø0.9 ø0.05 Minimum bending radius [mm] (Reference) 20 D M9 N V 588 Auto switch part no. ATEX category 3 Z SAPC MAPC SPC MPC SDPC MDPC Wiring and output N 3-wire NPN P 3-wire PNP 2-wire Electrical entry direction In-line V Perpendicular ead wire length 0.5 m 3 m 5 m 0.5 m + M8-3 pins pre-wired connector 1 m + M8-3 pins pre-wired connector 0.5 m + M8-4 pins pre-wired connector 1 m + M8-4 pins pre-wired connector 0.5 m + M12-4 pins pre-wired connector 1 m + M12-4 pins pre-wired connector Connector Specifications Connector type M8-3 pins M8-4 pins M12-4 pins Pin arrangement

80 2-Colour Solid State Switch/Direct Mounting D-M9NW(V) D-M9PW(V) D-M9W(V)-588 RoHS II 3G Ex na II T5 X 10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Auto Switch Specifications PC: Programmable ogic Controller D-M9W/D-M9WV (With 2 colour indicator light) Auto switch part no. D-M9NW D-M9NWV D-M9PW D-M9PWV D-M9W D-M9WV Electrical entry direction In-line Perpendicular In-line Perpendicular In-line Perpendicular Wiring type 3-wire 2-wire Output type NPN PNP Applicable load Power supply Current consumption IC circuit, Relay, PC 5/12/24 VDC (4.5 to 28 V) 10 ma or less 24 VDC relay, PC oad voltage 28 VDC or less 24 VDC (10 to 28V) oad current 40 ma or less 2.5 to 40 ma Internal voltage drop eakage current 0.8 V or less at 10 ma (2 V or less at 40 ma) 100 µa or less at 24 VDC 4 V or less 0.8 ma or less Indicator light Standard Operating position... Red ED illuminates. Optimum operating position... Green ED illuminates. CE marking This category 3 type auto switch can only be used in zones 2 and 22. Oilproof Flexible Heavy-duty ead Wire Specifications Auto switch model Sheath Outside diameter [mm] Number of cores Insulator Outside diameter [mm] Cross section [mm 2 ] Conductor Strand diameter [mm] Minimum bending radius [mm] (Reference) D M9 N W V 588 Auto switch part no. ATEX category 3 Wiring and output N 3-wire NPN P 3-wire PNP 2-wire M Z SAPC MAPC SPC MPC SDPC MDPC 2 colour display Electrical entry direction In-line V Perpendicular ead wire length 0.5 m 1 m 3 m 5 m 0.5 m + M8-3 pins pre-wired connector 1 m + M8-3 pins pre-wired connector 0.5 m + M8-4 pins pre-wired connector 1 m + M8-4 pins pre-wired connector 0.5 m + M12-4 pins pre-wired connector 1 m + M12-4 pins pre-wired connector D-M9NW D-M9PW D-M9W 2.7 x 3.2 (ellipse) 3 cores (rown/lue/lack) 2 cores (rown/lue) ø ø Connector Specifications Connector type M8-3 pins M8-4 pins M12-4 pins Pin arrangement

81 Solid State Switch/and Mounting D-H7A2-588 II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Auto Switch Specifications PC: Programmable ogic Controller D-H7 A2(With indicator light) Auto switch part no. D-H7A2 Wiring type 3-wire Output type PNP Applicable load IC circuit/relay/pc Power supply 5/12/24 VDC (4.5 to 28 VDC) Current consumption 10 ma or less oad current 80 ma or less Internal voltage drop 0.8 V or less eakage current 100 µa or less at 24 VDC Indicator light Red ED illuminates when turned ON. Standard CE marking This category 3 type auto switch can only be used in zones 2 and 22. Oilproof Heavy-duty ead Wire Specifications Auto switch model D-H7A2 Sheath Outside diameter [mm] ø3.4 Insulator Conductor Number of cores Cross section [mm 2 ] 3 cores (rown/lue/lack) 0.2 Outside diameter [mm] Strand diameter [mm] ø1.1 ø0.08 Minimum bending radius [mm] (Reference) 21 Z SAPC MAPC SPC MPC SDPC MDPC D H7A2 588 Auto switch part no. ATEX category 3 ead wire length 0.5 m 3 m 5 m 0.5 m + M8-3 pins pre-wired connector 1 m + M8-3 pins pre-wired connector 0.5 m + M8-4 pins pre-wired connector 1 m + M8-4 pins pre-wired connector 0.5 m + M12-4 pins pre-wired connector 1 m + M12-4 pins pre-wired connector Connector Specifications Connector type M8-3 pins M8-4 pins M12-4 pins Pin arrangement

82 Solid State Switch/Rail Mounting D-F7P(V)-588 II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Auto Switch Specifications PC: Programmable ogic Controller D-F7P, D-F7PV (With indicator light) Auto switch part no. D-F7P D-F7PV Wiring type Output type Applicable load Power supply Current consumption oad current Internal voltage drop eakage current Indicator light Standard 3-wire PNP IC circuit/relay/pc 5/12/24 VDC (4.5 to 28 VDC) 10 ma or less 80 ma or less 0.8 V or less 100 µa or less at 24 VDC Red ED illuminates when turned ON. CE marking This category 3 type auto switch can only be used in zones 2 and 22. Oilproof Heavy-duty ead Wire Specifications Auto switch model D-F7P Sheath Outside diameter [mm] ø3.4 Insulator Conductor Number of cores Cross section [mm 2 ] 3 cores (rown/lue/lack) 0.2 Outside diameter [mm] Strand diameter [mm] ø1.1 ø0.08 Minimum bending radius [mm] (Reference) 21 D F7P 588 Auto switch part no. ATEX category 3 Z SAPC MAPC SPC MPC SDPC MDPC Electrical entry direction In-line V Perpendicular ead wire length 0.5 m 3 m 5 m 0.5 m + M8-3 pins pre-wired connector 1 m + M8-3 pins pre-wired connector 0.5 m + M8-4 pins pre-wired connector 1 m + M8-4 pins pre-wired connector 0.5 m + M12-4 pins pre-wired connector 1 m + M12-4 pins pre-wired connector Connector Specifications Connector type M8-3 pins M8-4 pins M12-4 pins Pin arrangement

83 Solid State Switch/Tie-rod Mounting D-F5P-588 II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Auto Switch Specifications PC: Programmable ogic Controller D-F5P (With indicator light) Auto switch part no. D-F5P Wiring type 3-wire Output type PNP Applicable load IC circuit/relay/pc Power supply 5/12/24 VDC (4.5 to 28 VDC) Current consumption 10 ma or less oad current 80 ma or less Internal voltage drop 0.8 V or less eakage current 100 µa or less at 24 VDC Indicator light Red ED illuminates when turned ON. Standard CE marking This category 3 type auto switch can only be used in zones 2 and 22. Oilproof Heavy-duty ead Wire Specifications Auto switch model D-F5P Sheath Outside diameter [mm] ø4 Insulator Conductor Number of cores Cross section [mm 2 ] 3 cores (rown/lue/lack) 0.3 Outside diameter [mm] Strand diameter [mm] ø1.22 ø0.08 Minimum bending radius [mm] (Reference) 24 Z SAPC MAPC SPC MPC SDPC MDPC D F5P 588 Auto switch part no. ATEX category 3 ead wire length 0.5 m 3 m 5 m 0.5 m + M8-3 pins pre-wired connector 1 m + M8-3 pins pre-wired connector 0.5 m + M8-4 pins pre-wired connector 1 m + M8-4 pins pre-wired connector 0.5 m + M12-4 pins pre-wired connector 1 m + M12-4 pins pre-wired connector Connector Specifications Connector type M8-3 pins M8-4 pins M12-4 pins Pin arrangement

84 Solid State Switch/Direct Mounting D-Y7P(V)-588 II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Auto Switch Specifications PC: Programmable ogic Controller D-Y7P/D-Y7PV (With indicator light) Auto switch part no. Electrical entry direction D-Y7P In-line D-Y7PV Perpendicular Wiring type Output type Applicable load Power supply Current consumption oad current Internal voltage drop eakage current Indicator light Standard 3-wire PNP IC circuit/relay/pc 5/12/24 VDC (4.5 to 28 VDC) 10 ma or less 80 ma or less 0.8 V or less 100 µa or less at 24 VDC Red ED illuminates when turned ON. CE marking This category 3 type auto switch can only be used in zones 2 and 22. Oilproof Flexible Heavy-duty ead Wire Specifications Auto switch model D-Y7P Sheath Outside diameter [mm] ø3.4 Insulator Conductor Number of cores Cross section [mm 2 ] 3 cores (rown/lue/lack) 0.15 Outside diameter [mm] Strand diameter [mm] ø1.0 ø0.05 Minimum bending radius [mm] (Reference) 21 D Y7P 588 Auto switch part no. ATEX category 3 Z SAPC MAPC SPC MPC SDPC MDPC Electrical entry direction In-line V Perpendicular ead wire length 0.5 m 3 m 5 m 0.5 m + M8-3 pins pre-wired connector 1 m + M8-3 pins pre-wired connector 0.5 m + M8-4 pins pre-wired connector 1 m + M8-4 pins pre-wired connector 0.5m + M12-4 pins pre-wired connector 1m + M12-4 pins pre-wired connector Connector Specifications Connector type M8-3 pins M8-4 pins M12-4 pins Pin arrangement

85 Solid State Switch/Direct Mounting D-S7P-588 II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet/Connector Electrical entry: In-line Auto Switch Specifications PC: Programmable ogic Controller D-S7P1/D-S7P2 (With indicator light) Auto switch part no. D-S7P1 D-S7P2 Wiring type 3-wire Output type PNP Applicable load IC circuit/relay/pc Power supply 5/12/24 VDC (4.5 to 28 VDC) Current consumption 10 ma or less oad current 40 ma or less Internal voltage drop 0.8 V or less at 10 ma (2 V or less at 40 ma) eakage current 100 µa or less at 24 VDC Indicator light Red ED illuminates when turned ON. Standard CE marking This category 3 type auto switch can only be used in zones 2 and 22. D-S7P2 D-S7P1 Oilproof Heavy-duty ead Wire Specifications Auto switch model Sheath Outside diameter [mm] Number of cores Insulator Outside diameter [mm] Cross section [mm Conductor 2 ] Strand diameter [mm] Minimum bending radius [mm] (Reference) D-S7P ø3.4 3 cores (rown/lue/lack) ø ø eft hand mounting Right hand mounting D S7P 588 Auto switch part no. ATEX category Mounting Right hand mounting eft hand mounting Z SAPC MAPC SPC MPC SDPC MDPC ead wire length 0.5 m 3 m 5 m 0.5 m + M8-3 pins pre-wired connector 1 m + M8-3 pins pre-wired connector 0.5 m + M8-4 pins pre-wired connector 1m + M8-4 pins pre-wired connector 0.5 m + M12-4 pins pre-wired connector 1 m + M12-4 pins pre-wired connector Connector Specifications Connector type M8-3 pins M8-4 pins M12-4 pins Pin arrangement A

86 Solid State Switch/Direct Mounting D-S9P(V)-588 II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Auto Switch Specifications D-S9P/D-S9PV (With indicator light) Auto switch part no. D-S9P1 D-S9PV1 D-S9P2 D-S9PV2 Electrical entry direction In-line Perpendicular Wiring type 3-wire Output type PNP Applicable load IC circuit/relay/pc Power supply 5/12/24 VDC (4.5 to 28 VDC) Current consumption 10 ma or less oad current 40 ma or less Internal voltage drop 0.8 V or less at 10 ma (2 V or less at 40 ma) eakage current 100 µa or less at 24 VDC Indicator light Red ED illuminates when turned ON. Standard CE marking This category 3 type auto switch can only be used in zones 2 and 22. PC: Programmable ogic Controller D-S9P1 eft hand mounting D-S9PV1 eft hand mounting D-S9P2 Right hand mounting D-S9PV2 Right hand mounting Oilproof Heavy-duty ead Wire Specifications Auto switch model D-S9P Sheath Outside diameter [mm] Number of cores Insulator Outside diameter [mm] Cross section [mm Conductor 2 ] Strand diameter [mm] Minimum bending radius [mm] (Reference) D S9P 588 Auto switch part no. ATEX category 3 Electrical entry direction In-line V Perpendicular ø3.4 3 cores (rown/lue/lack) ø ø Mounting Right hand mounting eft hand mounting Z SAPC MAPC SPC MPC SDPC MDPC ead wire length 0.5 m 3 m 5 m 0.5 m + M8-3 pins pre-wired connector 1 m + M8-3 pins pre-wired connector 0.5 m + M8-4 pins pre-wired connector 1 m + M8-4 pins pre-wired connector 0.5 m + M12-4 pins pre-wired connector 1 m + M12-4 pins pre-wired connector Connector Specifications Connector type M8-3 pins M8-4 pins M12-4 pins Pin arrangement A

87 Solid State Switch for Hygienic Design Cylinder/Direct Mounting D-F6P-588 II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Auto Switch Specifications PC: Programmable ogic Controller D-F6P (With indicator light) Auto switch part no. D-F6P Electrical entry direction In-line Wiring type 3-wire Output type PNP Applicable load IC circuit, Relay, PC Power supply 5/12/24 VDC (4.5 to 28 V) Current consumption 10 ma or less oad current 40 ma or less Internal voltage drop 0.8 V or less eakage current 100 µa or less at 24 VDC Indicator light Red ED illuminates when turned ON. Standard CE marking This category 3 type auto switch can only be used in zones 2 and 22. Oilproof Flexible Heavy-duty ead Wire Specifications Auto switch model D-F6P Sheath Outside diameter [mm] 2.7 x 3.2 (ellipse) Insulator Conductor Number of cores Cross section [mm 2 ] 3 cores (rown/lue/lack) 0.15 Outside diameter [mm] Strand diameter [mm] ø0.9 ø0.05 Minimum bending radius [mm] (Reference) 20 Z SAPC MAPC SPC MPC SDPC MDPC D F6P 588 Auto switch part no. ATEX category 3 ead wire length 0.5 m 3 m 5 m 0.5 m + M8-3 pins pre-wired connector 1 m + M8-3 pins pre-wired connector 0.5 m + M8-4 pins pre-wired connector 1 m + M8-4 pins pre-wired connector 0.5 m+ M12-4 pins pre-wired connector 1 m+ M12-4 pins pre-wired connector Connector Specifications Connector type M8-3 pins M8-4 pins M12-4 pins Pin arrangement

88 Prior to Use Auto Switch/Internal Circuit Reed Auto Switch No. Internal Circuit 2-wire (Reed switch) 2-wire (Reed switch) 2-wire (Reed switch) 2-wire (Reed switch) rown rown rown rown Indicator circuit Contact protection circuit q lue oad Contact protection circuit w e r lue oad Indicator circuit lue Contact protection box oad lue Contact protection box oad No. Internal Circuit 3-wire (Reed switch, NPN) 2-wire (Reed switch) 2-wire (Reed switch) rown rown rown lack Indicator circuit t y u lue oad 2-color indicator circuit Contact protection circuit lue oad 2-color indicator circuit lue Contact protection box oad Contact Protection ox: CD-P12 <Applicable switch models> D-A73/A8, D-A73H/A80H, D-C73/C8, D-E73A/E80A, D-Z73/Z8, 9A, and D-A9/A9V type The auto switches above do not have a built-in contact protection circuit. A contact protection box is not required for solid state auto switches due to their construction. q Where the operation load is an inductive load. w Where the wiring length to load is greater than 5 m. Therefore, use a contact protection box with the switch for any of the above cases: The contact life may be shortened (due to permanent energizing conditions.) Even for the built-in contact protection circuit type (D-A54), use the contact protection box when the wiring length to load is very long (over 30 m) and PC (Programmable ogic Controller) with a large inrush current is used. Contact Protection ox Specifications Part no. CD-P12 oad voltage 24 VDC Max. load current 50 ma ead wire length Auto switch connection side 0.5 m oad connection side 0.5 m Contact Protection ox Internal Circuit CD-P12 rown Auto switch side lue Choke coil Zener diode rown(+) Contact Protection ox/dimensions oad side lue( ) Contact Protection ox Connection To connect a switch unit to a contact protection box, connect the lead wire from the side of the contact protection box marked SWITCH to the lead wire coming out of the switch unit. Keep the switch as close as possible to the contact protection box, with a lead wire length of no more than 1 meter. 79

89 Reed Switch/and Mounting D-C73/D-C II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Auto Switch Specifications D-C7 (With indicator light) Auto switch model number Applicable load oad voltage Max. load current and range Internal Circuit Contact protection circuit Internal voltage drop Indicator light Standards D-C8 (Without indicator light) Auto switch model number Applicable load oad voltage Max. load current Internal Circuit Contact protection circuit Internal resistance Standards PC: Programmable ogic Controller D-C73 Relay/PC 24 VDC 5 to 40 ma e None 2.4 V or less Red ED illuminates when turned ON AC 24 V or less DC 50 ma CE marking D-C80 Relay/PC/IC circuit r None AC 48 V DC 40 ma 1 Ω or less (Including 3 m lead wire) CE marking Oilproof Heavy-duty ead Wire Specifications Auto switch type D-C73/D-C80 Sheath Outside diameter [mm] ø3.4 Insulator Conductor [mm] Number of cores Cross section [mm 2 ] 2 cores (rown, lue) 0.2 Outside diameter [mm] Strand diameter [mm] ø1.1 ø0.08 Minimum bending radius of lead wire [mm] (Reference) 21 For internal circuit, refer to the Internal Circuit No. on page 79. This category 3 type auto switch can only be used in zones 2 and 22. D C 588 ATEX category 3 Auto switch model number 73 With indicator light 80 Without indicator light ead wire length 0.5 m 3 m Z 5 m (Except D-C80) 80

90 Reed Switch/Rail Mounting D-A73(H)/D-A80(H)-588 II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Electrical entry: Perpendicular Auto Switch Specifications PC: Programmable ogic Controller D-A73, D-A73H (With indicator light) Auto switch model number D-A73/D-A73H Applicable load Relay/PC oad voltage 24 VDC oad current range 5 to 40 ma Internal Circuit e Contact protection circuit None Internal voltage drop 2.4 V or less Indicator light Red ED illuminates when turned ON Standard CE marking D-A80, D-A80H (Without indicator light) Auto switch model number D-A80/D-A80H Applicable load Relay/IC circuit/pc oad voltage AC 24 V or less DC 48 V AC DC Max. load current Internal Circuit Contact protection circuit Internal resistance Standard 50 ma 40 ma r None 1 Ω or less (Including 3 m lead wire) CE marking Oilproof Heavy-duty ead Wire Specifications Auto switch type D-A73/D-A73H/D-A80/D-A80H Sheath Outside diameter [mm] ø3.4 Insulator Conductor Number of cores Cross section [mm 2 ] 2 cores (rown, lue) 0.2 Outside diameter [mm] Strand diameter [mm] ø1.1 ø0.08 Minimum bending radius of lead wire [mm] (Reference) 21 For internal circuit, refer to the Internal Circuit No. on page 79. This category 3 type auto switch can only be used in zones 2 and 22. D A 588 ATEX category 3 Auto switch model number 73 With indicator light 80 Without indicator light Electrical Entry Perpendicular H In-line ead wire length 0.5 m 3 m Z 5 m (Except A 80) 81

91 Reed Switch/Tie-rod Mounting D-A54/D-A II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Auto Switch Specifications D-A54 (With indicator light) Auto switch model number Applicable load oad voltage Max. load current and range Internal Circuit Contact protection circuit Internal voltage drop Indicator light Standard D-A67 (Without indicator light) Auto switch model number Applicable load oad voltage Max. load current and range Internal Circuit Contact protection circuit PC: Programmable ogic Controller D-A54 Relay/PC 24 VDC 5 to 50 ma q uilt-in 2.4 V or less (up to 20 ma) / 3.5 V or less (up to 50 ma) Red ED illuminates when turned ON CE marking D-A67 PC/IC circuit MAX. 24 VDC 30 ma r None Internal resistance Standard 1 Ω or less (Including 3 m lead wire) CE marking Oilproof Heavy-duty ead Wire Specifications Auto switch type D-A54/D-A67 Sheath Outside diameter [mm] ø4 Insulator Conductor Number of cores Cross section [mm 2 ] 2 cores (rown, lue) 0.3 Outside diameter [mm] Strand diameter [mm] ø1.22 ø0.08 Minimum bending radius of lead wire [mm] (Reference) 24 For internal circuit, refer to the Internal Circuit No. on page 79. This category 3 type auto switch can only be used in zones 2 and 22. D A 588 ATEX category 3 Auto switch model number 54 With indicator light 67 Without indicator light ead wire length 0.5 m 3 m Z 5 m (Except D-A67) 82

92 Reed Switch/Direct Mounting D-A90(V)/D-A93(V)-588 II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Auto Switch Specifications PC: Programmable ogic Controller D-A90, D-A90V (Without indicator light) Auto switch model number D-A90/D-A90V Applicable load IC circuit/relay/pc AC AC oad voltage 24 V or less 48 V or less DC DC Max. load current Internal Circuit Contact protection circuit Internal resistance 50 ma r None 1 Ω or less (Including 3 m lead wire) Standard CE marking D-A93, D-A93V (With indicator light) Auto switch model number D-A93/D-A93V Applicable load Relay/PC oad voltage 24 VDC Max. load current and load current range 5 to 40 ma Internal Circuit e Contact protection circuit None Internal voltage drop Indicator light Standard 40 ma D-A V or less (up to 20 ma)/3 V or less (up to 40 ma) D-A 93V 2.7 V or less Red ED illuminates when turned ON CE marking Oilproof Heavy-duty ead Wire Specifications Auto switch type D-A90 (V)/D-A93 (V) Sheath Outside diameter [mm] ø2.7 Insulator Conductor Number of cores Cross section [mm 2 ] 2 cores (rown, lue) 0.18 Outside diameter [mm] Strand diameter [mm] ø0.96 ø0.08 Minimum bending radius of lead wire [mm] (Reference) 17 For internal circuit, refer to the Internal Circuit No. on page 79. This category 3 type auto switch can only be used in zones 2 and 22. D A 588 ATEX category 3 Auto switch model number 93 With indicator light 90 Without indicator light Electrical Entry In-line V Perpendicular ead wire length 0.5 m 3 m Z 5 m (Except A90) 83

93 Reed Switch/Direct Mounting D-90A/D-93A-588 II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet ead wire: Heavy-duty cord Auto Switch Specifications D-90A (Without indicator light) Auto switch model number Applicable load oad voltage Max. load current Internal Circuit Internal resistance Standard D-93A (With indicator light) Auto switch model number Applicable load oad voltage oad current range Internal Circuit Internal voltage drop Indicator light Standard PC: Programmable ogic Controller D-90A Relay/IC circuit/pc AC 24 V DC 50 ma r 1 Ω or less (Including 3 m lead wire) CE marking D-93A Relay/PC 24 VDC 5 to 40 ma e 2.4V or less Red ED illuminates when turned ON CE marking Oilproof Heavy-duty ead Wire Specifications Auto switch type D-90A/D-93A Sheath Outside diameter [mm] ø3.4 Insulator Conductor Number of cores Cross section [mm 2] 2 cores (rown, lue) 0.2 Outside diameter [mm] Strand diameter [mm] ø1.1 ø0.08 Minimum bending radius of lead wire [mm] (Reference) 21 For internal circuit, refer to the Internal Circuit No. on page 79. This category 3 type auto switch can only be used in zones 2 and 22. D A 588 ATEX category 3 Auto switch model number 93 With indicator light 90 Without indicator light ead wire length 0.5 m 3 m Z 5 m 84

94 Reed Switch/Direct Mounting D-Z73/D-Z II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Auto Switch Specifications PC: Programmable ogic Controller D-Z73 (With indicator light) Auto switch model number D-Z73 Applicable load Relay/PC oad voltage 24 VDC Max. load current and range 5 to 40 ma Internal Circuit e Contact protection circuit None Internal voltage drop 2.4 V or less (up to 20 ma)/3 V or less (up to 40 ma) Indicator light Red ED illuminates when turned ON Standard CE marking D-Z80 (Without indicator light) Auto switch model number D-Z80 Applicable load Relay/PC/IC circuit oad voltage AC 24 V DC or less 48 V AC DC Max. load current Internal Circuit Contact protection circuit Internal resistance Standard 50 ma 40 ma r None 1 Ω or less (Including 3 m lead wire) CE marking Oilproof Heavy-duty ead Wire Specifications Auto switch type D-Z73/D-Z80 Sheath Outside diameter [mm] ø2.7 Insulator Conductor Number of cores Cross section [mm 2 ] 2 cores (rown, lue) 0.18 Outside diameter [mm] Strand diameter [mm] ø1.1 ø0.08 Minimum bending radius of lead wire [mm] (Reference) 17 For internal circuit, refer to the Internal Circuit No. on page 79. This category 3 type auto switch can only be used in zones 2 and 22. D Z 588 ATEX category 3 Auto switch model number 73 With indicator light 80 Without indicator light ead wire length 0.5 m 3 m Z 5 m (Except D-Z80) 85

95 Reed Switch/Direct Mounting D-E73A/D-E80A-588 II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Auto Switch Specifications D-E73A (With indicator light) Auto switch model number Applicable load oad voltage Max. load current and range Internal Circuit Contact protection circuit Internal voltage drop PC: Programmable ogic Controller D-E73A Relay/PC 24 VDC 5 to 40 ma e None 2.4 V or less Indicator light Standard D-E80A (Without indicator light) Auto switch model number Applicable load oad voltage Red ED illuminates when turned ON CE marking AC 24 V DC or less D-E80A Relay/PC/IC circuit 48 V AC DC Max. load current Internal Circuit Contact protection circuit Internal resistance Standard 50 ma 40 ma r None 1 Ω or less (Including 3 m lead wire) CE marking Oilproof Heavy-duty ead Wire Specifications Sheath Insulator Conductor Auto switch type Outside diameter [mm] Number of cores Outside diameter [mm] Cross section [mm 2 ] Strand diameter [mm] D-E73A/D-E80A ø3.4 2 cores (rown, lue) ø ø0.08 Minimum bending radius of lead wire [mm] (Reference) 21 For internal circuit, refer to the Internal Circuit No. on page 79. This category 3 type auto switch can only be used in zones 2 and 22. D E A 588 ATEX category 3 Auto switch model number 73 With indicator light 80 Without indicator light ead wire length 0.5 m 3 m 86

96 Reed Switch/Direct Mounting D-R73/D-R II 3G Ex na II T5 X -10 C Ta +60 C II 3D Ex td A22 IP67 T93 C X Grommet Electrical entry: In-line Auto Switch Specifications PC: Programmable ogic Controller D-R73 (With indicator light) Auto switch model number D-R731/D-R732 Applicable load Relay/PC oad voltage 24 VDC oad current range 5 to 40 ma Internal Circuit e Internal voltage drop 2.4 V or less Indicator light Red ED illuminates when turned ON Standard CE marking D-R80 (Without indicator light) Auto switch model number D-R801/D-R802 Applicable load Relay/IC circuit/pc oad voltage 24 V AC DC D-R2 D-R1 Max. load current Internal Circuit 50 ma r Internal resistance 1 Ω or less (Including 3 m lead wire) Standard CE marking eft hand mounting Right hand mounting Oilproof Heavy-duty ead Wire Specifications Auto switch type D-R73/D-R80 Sheath Outside diameter [mm] ø3.4 Insulator Conductor Number of cores Cross section [mm 2 ] 2 cores (rown, lue) 0.2 Outside diameter [mm] Strand diameter [mm] ø1.1 ø0.08 Minimum bending radius of lead wire [mm] (Reference) 21 For internal circuit, refer to the Internal Circuit No. on page 79. This category 3 type auto switch can only be used in zones 2 and 22. D R 588 ATEX category 3 Auto switch model number 73 With indicator light 80 Without indicator light 1 2 Mounting Right hand mounting eft hand mounting ead wire length 0.5 m 3 m Z 5 m 87

97 Rotary Actuator: Vane Type Series 55-CR1 Sizes: 50, 63, 80, 100 II 2Gc 90 C (T5) Ta 5 C to 40 C 110 C (T4) Ta 40 C to 60 C Standard 55 CR1 W S ATEX category 2 W Mounting asic Foot Shaft type Double shaft (long shaft with key and short shaft with four flats) Standard Semistandard Size Rotating angle Classification Symbol Single vane Double vane Thread Port -XF -XN Rc G NPT Connecting port position Side ports E Axial ports A port port Side ports olt A port port Axial ports ody end of the short-shaft side Vane type S D Single vane Double vane All other specifications are the same as the standard products Series CR1. For details, refer to the WE catalog or est Pneumatics No

98 Rotary Actuator: Vane Type Series 56-CR1 Sizes: 50, 63, 80, 100 II 3G 84 C (T6) Ta 5 C to 40 C 104 C (T4) Ta 40 C to 60 C Without magnet 56 CR1 W S With magnet 56 CDR1 W S ATEX category 3 With auto switch unit uilt-in magnet Mounting asic Foot Size Thread Port -XF -XN Rc G NPT Connecting port position Side ports E Axial ports olt W Shaft type Double shaft (long shaft key & four chamfers) Rotating angle Classification Symbol Single vane Double vane Standard Semistandard Vane type S D A port Side ports Single vane Double vane port A port port Axial ports ody end of the short-shaft side All other specifications are the same as the standard products Series CR1. For details, refer to the WE catalog or est Pneumatics No. 4. Refer to page 69 for applicable auto switches. 89

99 Rotary Actuator: Vane Type Series 55-CR2 Sizes: 10, 15, 20, 30, 40 II 2Gc 130 C (T4) Ta 5 C to 40 C 150 C (T3) Ta 40 C to 60 C Standard 55 CR2 W 180 S E Z W S ATEX category 2 Mounting asic type F Flange type F: Except size 40 Shaft type Double shaft with single flat (sizes 10 to 30) ong shaft key, Short shaft with single flat (size 40) Single shaft (ong shaft) with single flat (sizes 10 to 30) ong shaft with key (size 40) Size Connecting port position Side ports E Axial ports Vane type S D Single vane Double vane Single vane Double vane Rotation All other specifications are the same as the standard products Series CR2. For details, refer to the WE catalog or est Pneumatics No a

100 Rotary Actuator: Vane Type Series 56-CR2 Sizes: 10, 15, 20, 30, 40 II 3G 100 C (T5) Ta 5 C to 40 C 120 C (T4) Ta 40 C to 60 C Without magnet With magnet 56 CR2 56 CDR2 W W 180 S E 180 S Z Z Connecting port position Side ports E Axial ports ATEX category 3 With auto switch unit uilt-in magnet Mounting asic F Flange F: Except size 40 Size Vane type S D Single vane Double vane Shaft type Double shaft with single flat (sizes 10 to 30) W ong shaft with key, short shaft with single flat (size 40) S Single shaft (ong shaft) with single flat (sizes 10 to 30) ong shaft with key (size 40) Cannot be selected when mounting an auto switch Rotation Single vane Double vane All other specifications are the same as the standard products Series CR2. For details, refer to the WE catalog or est Pneumatics. Refer to page 69 for applicable auto switches. 91 b

101 Rotary Actuator: Free Mount Type Series 55-CRU2 Sizes: 10, 15, 20, 30, 40 II 2Gc 130 C (T4) Ta 5 C to 40 C 150 C (T3) Ta 40 C to 60 C Standard 55 CRU2 W 180 S E Z W S ATEX category 2 Free mount type Shaft type Double shaft with single flat (sizes 10 to 30) ong shaft with key, short shaft with single flat (size 40) Single shaft (ong shaft) with single flat (sizes 10 to 30) ong shaft with key (size 40) Size Rotation Single vane Double vane Connecting port position Side ports E Axial ports Vane type S Single vane D Double vane All other specifications are the same as the standard products Series CRU2. For details, refer to the WE catalog or est Pneumatics No a

102 Rotary Actuator: Free Mount Type Series 56-CRU2 Sizes: 10, 15, 20, 30, 40 II 3G 100 C (T5) Ta 5 C to 40 C 120 C (T4) Ta 40 C to 60 C Without magnet With magnet 56 CRU2 W 180 S 56 CDRU2 W 180 S E Z Z Connecting port position Side ports E Axial ports ATEX category 3 With auto switch unit uilt-in magnet Free mount type Shaft type Double shaft with single flat (sizes 10 to 30) W ong shaft with key, short shaft with single flat (size 40) S Single shaft (ong shaft) with single flat (sizes 10 to 30) ong shaft with key (size 40) Cannot be selected when mounting an auto switch Size Rotation Single vane Double vane Vane type S Single vane D Double vane All other specifications are the same as the standard products Series CRU2. For details, refer to the WE catalog or est Pneumatics. Refer to page 69 for applicable auto switches. 93 b

103 Compact Rotary Actuator Rack & Pinion Type Series 55-CRQ2 II 2Gc 70 C (T6) Ta 0 C to 40 C 90 C (T5) Ta 40 C to 60 C Without magnet 55 CRQ2 S With magnet 55 CDRQ2 S ATEX category 2 uilt-in magnet for auto switch Shaft type S Single shaft W Double shaft Size Cushion Symbol C Rotation to to 190 Cushion Without cushion Rubber cushion Air cushion Size Size 10, 15 20, 30, 40 Port thread Port thread TF TN TT M5 Rc 1/8 G 1/8 NPT 1/8 NPTF 1/8 All other specifications are the same as the standard products Series CRQ2. For details, refer to the WE catalog or est Pneumatics No. 4. Refer to page 69 for applicable auto switches. 94

104 Compact Rotary Actuator Rack & Pinion Type Series 56-CRQ2 II 3G 60 C (T6) Ta 0 C to 40 C 80 C (T6) Ta 40 C to 60 C Without magnet 56 CRQ2 S With magnet 56 CDRQ2 S ATEX category 3 uilt-in magnet for auto switch Shaft type S Single shaft W Double shaft Size Cushion Symbol C Rotation to to 190 Cushion Without cushion Rubber cushion Air cushion Size Size 10, 15 20, 30, 40 Port thread Port thread TF TN TT M5 Rc 1/8 G 1/8 NPT 1/8 NPTF 1/8 All other specifications are the same as the standard products Series CRQ2. For details, refer to the WE catalog or est Pneumatics No. 4. Refer to page 69 for applicable auto switches. 95

105 ooster Regulator Series 56-VA 10A to 43A II 3 GD c T6 Ta 2 C to 50 C RoHS 56-VA 40A 04 10A 11A 20A 40A 22A 42A 43A ATEX category 3 1/4, Handle-operated type 1/4, Handle-operated type 3/8, Handle-operated type 1/2, Handle-operated type 3/8, Air-operated type 1/2, Air-operated type 1/2, Max. operating pressure 1.6 Mpa ody size Pressure increase ratio: Twice Pressure increase ratio: 2 to 4 times Pressure increase ratio: Twice Thread type Note) Symbol Thread type Rc F G N NPT T NPTF Note) Thread types apply to the IN, OUT, and EXH ports of the VA1A and to the IN, OUT, EXH, and gauge ports of the VA2A and VA4A. The gauge ports of the VA1A are Rc thread type regardless of the thread type indication. Port size Symbol Port size 02 1/4" 03 3/8" 04 1/2" Semi-standard Symbol Specifications Standard product Pressure unit on the product name label Z Note) and pressure gauge: psi Note) Thread type: NPT, NPTF Under the new measurement law, the pressure unit of psi on the pressure gauges cannot be used in Japan. Options Symbol Options None G Pressure gauge N Silencer S High-noise reduction silencer Note) GN Pressure gauge, Silencer GS Pressure gauge, High-noise reduction silencer Note) N Elbow silencer Note) S Elbow high-noise reduction silencer Note) GN Pressure gauge, Elbow silencer Note) GS Pressure gauge, Elbow high-noise reduction silencer Note) Note) Refer to Combination of Thread Type and Options. Applicable series VA1A VA2A VA4A Combination of Thread Type and Options ody size 10A 11A 20A 22A 40A 42A 43A Thread type F N T F N T F N T G Options Semi-standard N S GN GS N S GN GS -Z All other specifications are the same as the standard products Series VA. For details, refer to the WE catalog or est Pneumatics No

106 Digital Pressure Switch for Air Series 56-ISE70 II 3G Ex na II T5 X 0 C Ta 50 C II 3D td A22 IP67 T53 C X 1MPa 56 ISE M ATEX category 3 Piping specifications 02 Rc1/4 N02 NPT1/4 F02 G1/4 (ISO1179) Option 2 None With bracket Output specifications 27 2 settings NPN open collector 2 outputs (Pin no.: 2, 4) A 43 Fixed setting: (The pressure set point for switching the output signal is common to NPN and PNP.) NPN open collector 1 output (Pin no.: 4) + PNP open collector 1 output (Pin no.: 2) Note) Mounting screws are not included Fixed setting PNP open collector 1 output (Pin no.: 4) 2 settings PNP open collector 2 outputs (Pin no.: 2, 4) M P Unit specifications With display unit switching function Note 1) Fixed SI unit Note 2) Pressure unit: psi (Initial value) With display unit switching function Note 1) Option 1 None ead wire with M12 connector (5 m), S straight ead wire with M12 connector (5 m), right-angled Note 1) Under the New Measurement aw, sales of switches with the unit switching function are not allowed for use in Japan. (Initial value: MPa) Note 2) Fixed unit: Mpa Specifications Model 56-ISE70 Rated pressure range 0 to 1 MPa Pressure display range/set pressure range 0.1 to 1 MPa Withstand pressure 1.5 MPa Pressure display resolution/minimum unit setting 0.01 MPa Applicable fluid Air, Non-corrosive gas, Non-flammable gas Power supply voltage 12 to 24 VDC±10%, Ripple (p-p) 10% or less (with power supply polarity protection) Current consumption 55 ma or less (at no load) Follow the instructions given below when handling the pressure switch. Operating temperature range is 0 to 50 C Do not expose the pressure switch to heat radiation from a heat source located nearby. It can cause malfunction. Do not expose the pressure switch/connector/cable to vibration and impact. Otherwise it can cause damage or malfunction. Protect the product from direct sunlight or UV light using a suitable protective cover. Do not disconnect the M12 connector while energized. Use only an ATEX approved M12 connector. For cleaning this product, use a clean and damp cloth, to prevent the buildup of an electrostatic charge. Ground properly to prevent the buildup of an electrostatic charge. All other specifications are the same as the standard products Series ISE70. For details, refer to the WE catalog or est Pneumatics No

107 Digital Pressure Switch for General Fluids Series 56-ISE75/75H II 3G Ex na II T4 X -5 C Ta 50 C II 3D td A22 IP67 T54 C X 10MPa 56 ISE M 15MPa 56 ISE75H M ATEX category 3 Piping specifications 02 N02 F02 Rc1/4 NPT1/4 G1/4 (ISO1179) Option 2 None With bracket Output specifications settings NPN open collector 2 outputs (Pin no.: 2, 4) Fixed setting: (The pressure set point for switching the output signal is common to NPN and PNP.) NPN open collector 1 output (Pin no.: 4) + PNP open collector 1 output (Pin no.: 2) Fixed setting PNP open collector 1 output (Pin no.: 4) 2 settings PNP open collector 2 outputs (Pin no.: 2, 4) M P Unit specifications With display unit switching function Note 1) Fixed SI unit Note 2) Pressure unit: psi (Initial value) With display unit switching function Note 1) Option 1 None ead wire with M12 connector (5 m), S straight A Note) Mounting screws are not included. ead wire with M12 connector (5 m), right-angled Note 1) Under the New Measurement aw, sales of switches with the unit switching function are not allowed for use in Japan. (Initial value: MPa) Note 2) Fixed unit: Mpa Specifications Model 56-ISE75 56-ISE75H Rated pressure range Pressure display range/set pressure range Withstand pressure 0 to 10 MPa 0.4 to 10 MPa 30 MPa 0 to 15 MPa 0.5 to 15 MPa 45 MPa Pressure display resolution/minimum unit setting Applicable fluid Power supply voltage Current consumption 0.1 MPa Fluid or gas that will not corrode SUS304, SUS430 and SUS to 24 VDC±10%, Ripple (p-p) 10% or less (with power supply polarity protection) 55 ma or less (at no load) Follow the instructions given below when handling the pressure switch. Operating temperature range is 5 to 50 C Do not expose the pressure switch to heat radiation from a heat source located nearby. It can cause malfunction. Do not expose the pressure switch/connector/cable to vibration and impact. Otherwise it can cause damage or malfunction. Protect the product from direct sunlight or UV light using a suitable protective cover. Do not disconnect the M12 connector while energized. Use only an ATEX approved M12 connector. For cleaning this product, use a clean and damp cloth, to prevent the buildup of an electrostatic charge. Ground properly to prevent the buildup of an electrostatic charge. All other specifications are the same as the standard products Series ISE75/ISE75H. For details, refer to the WE catalog or est Pneumatics No

108 2 Port Steam Valve Steam Valve Series 56-VND Note) S II 3G TX -5 C Ta 60 C ody option Standard (Copper alloy) Stainless steel body Note) Threaded type only Thread type Rc F G N NPT T NPTF Air operated 56 VND 2 0 D S 15A ATEX category 3 Valve size Symbol Orifice dia. (mm) ø7 ø15 ø20 ø25 ø32 ø40 ø50 Valve type Symbol N.C. N.O. N.C. Symbol 6A 8A 10A 10A 15A 20A 25A 32A 32F 40A 40F 50A 50F Options Note) Note) Port size Rc None With bracket With indicator light(visual verification of operation) With bracket and indicator light(visual verification of operation) Note) rackets (for valve size 1/2/3/4 only) will be assembled at the time of shipment. racket part no. Valve size 1: VN1-A16 (with thread) Valve size 2 to 4: VN-16 2 to 4 Port size Flange Flange 2 2 Flange All other specifications are the same as the standard products Series VND. For details, refer to the WE catalog or est Pneumatics No

109 Valve for Water and Chemical ase Fluids (2/3 Port Air Operated Valve) Series VCC II 2GD c 75 C T6 X +5 C Ta +50 C Valve 2 3 2D VCC Passage number 2 port valve 3 port valve Note) 2 port/diaphragm type (Applicable for 2 liquid paint) Note) Pressure cannot be applied from a 3 port valve RETURN port. Port size F For manifold mounting Rc1/4 (for single unit) Note) G1/4 (for single unit) Note) Note) Part number for sub-base 02 [Rc1/4] For 2 port: VCC12-S- 02F [G1/4] 02 [Rc1/4] For 3 port: VCC13-S- 02F [G1/4] VCC12(D)-00 VCC12(D)-02(F) VCC13-00 VCC13-02(F) Manifold Standard VV M CC C4 Type (Passage number) 2 2 port valve, Cleaning valve 3 3 port valve M 2/3 port valves mixed mounting Pilot port fitting size C4 C6 ø4 One-touch fitting (Antistatic) ø6 One-touch fitting (Antistatic) 2 port valve mountable number 00 No 2 port valves used 02 2 pcs. (colours) 04 4 pcs. (colours) 3 port valve mountable number No 3 port valves used 2 pcs. (colours) 4 pcs. (colours) Note) Maximum mountable valve number: 40 pcs. (total of 2 port and 3 port valves) Circuit example 2 port valve IN PA IN PA IN PA IN RETURN PA IN 3 port valve RETURN PA IN RETURN PA 2 port valve 1 pc. 3 pcs. 5 pcs. 3 port valve 1 pc. 3 pcs. 5 pcs. IN PA IN PA IN PA IN PA IN RETURN PA IN RETURN PA RETURN OUT 2 pcs. 4 pcs. 6 pcs. 2 pcs. 4 pcs. 6 pcs. All other specifications are the same as the standard products Series VCC. For details, refer to the WE catalog or est Pneumatics No

110 Valve for Water and Chemical ase Fluids Series VCC Manifold With gate valve VV M CC C4 G 04 2 M Passage number 2 port valve, Cleaning valve 2/3 port valves mixed mounting 2 port valve mountable number 00 No 2 port valves used 02 2 pcs. (colours) 04 4 pcs. (colours) Gate valve and cleaning valve mountable number Cleaning valve (2 port valve): 1 pc. + Gate valve: 1 pc. Cleaning valve (2 port valve): 3 pcs. + Gate valve: 1 pc. Cleaning valve (2 port valve): 5 pcs. + Gate valve: 1 pc. Pilot port fitting size C4 C6 ø4 One-touch fitting (Antistatic) ø6 One-touch fitting (Antistatic) 3 port valve mountable number 00 No 3 port valves used 02 2 pcs. (colours) 04 4 pcs. (colours) Circuit example Note) Maximum mountable valve number: 40 pcs. (total of 2 port, 3 port and gate valves) The gate valve and cleaning valve (2 port valve) are not included. They are ordered separately. (Gate valve is equivalent to 2 port valve.) When cleaning valve number is an even number, use the blanking plug for 2 port valve. Gate/Cleaning valve 2/3 port valve Cleaning valve IN PA IN PA IN PA IN RETURN PA IN RETURN PA IN RETURN PA Cleaning valve OUT Cleaning valve IN PA PA Gate valve IN PA IN PA IN RETURN PA IN RETURN PA RETURN Gate valve OUT All other specifications are the same as the standard products Series VCC. For details, refer to the WE catalog or est Pneumatics No