E5AN-H/E5EN-H(96 x 96 mm and 48 x 96 mm)

Transcription

1 Advaned Digital Temperature Controller E5AN-H/E5EN-H(96 x 96 mm and 48 x 96 mm) A New High-performane Controller: High Resolution, High Speed, and High Input Auray. With Logi Operations and preventive maintenane funtions. Plus Infrared Port on Front Panel. High-resolution display with 5 digits/. C display. High-speed sampling yle of 6 ms. High Auray Thermoouple/Pt : ±.% of PV Analog : ±.% FS Universal s on all models (thermoouple, PT, analog) to handle various sensors with one Controller. odels also available with Remote SP. A PV/SV-status display funtion an be set to displaying the PV or SV and the status of the Temperature Controller (auto/manual, RUN/STOP and alarms). Flexible ontat s with logi operations (AND, OR, and delays) set from the Support Software (C-Thermo Ver. 4.) Preventive maintenane for relays using a Control Output / Counter. odel available with position-proportional ontrol ain I/O Funtions mm E5AN-H mm E5EN-H Refer to Safety Preautions on page 22. Remote SP Input E5AN-H E5EN-H Event Inputs None Two Four 3-line Display Simultaneously displays set items, suh as the PV, SV, and V. 5-digit, segment display with high resolution of. C Universal Sensor Inputs Universal thermoouple/ Pt/analog (urrent/voltage) s. Indiation Auray Thermoouple/Pt : ±.% of PV Analog : ±.% FS Sampling Period and ontrol update 6 ms PF Key (Programmable key funtion) Infrared port USB Control Output 2 (built-in) SSR s Control Output (built-in) SSR s Auxiliary Outputs Two Three Computer Support Software C-Thermo Output Unit Relay Voltage (for driving SSR) Current Linear voltage Output Unit Relay Voltage (for driving SSR) Current Linear voltage Auto/manual swithing Temperature Controller status display Simple program funtion Logi operations Control / ount alarm PV hange rate alarm odels optional with RS-485 or RS-232C ommuniations Advaned Digital Temperature Controller E5AN-H/E5EN-H

2 Lineup E5AN-H/E5EN-H Advaned Type Terminal blok Universal ontrol 2 auxiliary s 2 ontrol s 2 auxiliary s Note: All ontrollers an be used for Heating, Cooling and Heating & Cooling ontrol. odel Number Struture odel Number Legend Controllers E5AN/E5EN-H@@@@@@@ Type H: Advaned Control mode, and 2 AA: 2 slots for ontrol module SS: 2 SSR s fitted PRR: position (valve) ontrol, 2 Relays fitted 5. Auxiliary Outputs 2: Two s 3: Three s 6. Option Blank: None H: Heater burnout/ssr failure/heater overurrent detetion (For -phase heater appliations, x CT) HH: Heater burnout/ssr failure/heater overurrent detetion (For 3-phase heater appliations, 2x CT) 7. Option 2 B: Two event s BF: Event + Transfer 8. Option 3 : Option Unit an be mounted. Option Units E53-@. Funtion EN: RS-232C ommuniations EN2: RS-422 ommuniations EN3: RS-485 ommuniations AKB: Event Output Units E53-@. Funtion RN: relay QN: pulse (PNP) 2 VDC Q3: pulse (NPN) 2 VDC Q4: pulse (PNP) 24 VDC C3N: linear 4 to 2 ma C3DN: linear to 2 ma V34N: linear to V V35N: linear to 5 V 9. Power Supply Voltage Blank: to 24 VAC D: 24 VAC/VDC. Terminal Cover -5: With Terminal Cover Note: Casing olor is blak. White/Silver available on request. This data sheet is provided as a guideline for seleting produts. Be sure to refer to the following user manuals for appliation preautions and other information required for operation before attempting to use the produt. E5CN-H/E5AN-H/E5EN-H Digital Controllers User's anual Advaned Type (Cat. No. H57) E5CN-H/E5AN-H/E5EN-H Digital Controllers Communiations anual Advaned Type (Cat. No. H59) 2 Advaned Digital Temperature Controller E5AN-H/E5EN-H

3 Ordering Information E5AN-H Size /4 DIN (W H D) Case olor Blak Power supply voltage to 24 VAC 24 VAC/ VDC Control method Basi Auxiliary 2 3 Valve 2 Basi 2 3 Valve 2 Control /2 Heater burnout none fitted, 2 slots -phase 2 2 SSR fitted -phase 2 none fitted, 2 slots 3-phase 2 2 SSR fitted 3-phase 2 none fitted, 2 slots 2 2 SSR fitted 2 2 relay fitted 2 2 relay fitted 2 none fitted, 2 slots -phase 2 2 SSR fitted -phase 2 none fitted, 2 slots 3-phase 2 2 SSR fitted 3-phase 2 none fitted, 2 slots 2 2 SSR fitted 2 2 relay fitted 2 2 relay fitted 2 Event s Optional funtions Transfer 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA Remote setpoint 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA odel E5AN-HAA2HB-5 E5AN-HSS2HB-5 E5AN-HAA2HHBF-5 E5AN-HSS2HHBF-5 E5AN-HAA3BF-5 E5AN-HSS3BF-5 E5AN-HPRR2B-5 E5AN-HPRR2BF-5 E5AN-HAA2HBD-5 E5AN-HSS2HBD-5 E5AN-HAA2HHBFD-5 E5AN-HSS2HHBFD-5 E5AN-HAA3BFD-5 E5AN-HSS3BFD-5 E5AN-HPRR2BD-5 E5AN-HPRR2BFD-5 Note: Add power supply voltage to model to omplete ordering ode (ie. E5AN-HAA2HB-5 AC-24 or E5AN-HAA2HBD-5 AC/DC24) Note: Heater alarm = heater burnout + SSR short detetion + SSR overurrent Note: For option modules (AA), see modules E53-_ N on page 2 Advaned Digital Temperature Controller E5AN-H/E5EN-H 3

4 E5EN-H Size Case olor Power supply voltage Control method Auxiliary Control /2 Heater burnout Event s Optional Funtions Transfer Remote setpoint odel none fitted, 2 slots -phase 2 4 to 2-mA E5EN-HAA2HB-5 to 24 VAC Basi SSR fitted -phase 2 none fitted, 2 slots 3-phase 2 2 SSR fitted 3-phase 2 none fitted, 2 slots 2 2 SSR fitted 2 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA E5EN-HSS2HB-5 E5EN-HAA2HHBF-5 E5EN-HSS2HHBF-5 E5EN-HAA3BF-5 E5EN-HSS3BF-5 /8 DIN (W H D) Blak Valve 2 2 relay fitted 2 2 relay fitted 2 none fitted, 2 slots -phase 2 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA E5EN-HPRR2B-5 E5EN-HPRR2BF-5 E5EN-HAA2HBD-5 24 VAC/ VDC Basi SSR fitted -phase 2 none fitted, 2 slots 3-phase 2 2 SSR fitted 3-phase 2 none fitted, 2 slots 2 2 SSR fitted 2 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA E5EN-HSS2HBD-5 E5EN-HAA2HHBFD-5 E5EN-HSS2HHBFD-5 E5EN-HAA3BFD-5 E5EN-HSS3BFD-5 Valve 2 2 relay fitted 2 2 relay fitted 2 4 to 2-mA 4 to 2-mA 4 to 2-mA E5EN-HPRR2BD-5 E5EN-HPRR2BFD-5 Note: Add power supply voltage to model to omplete ordering ode (ie. E5EN-HAA2HB-5 AC-24 or E5EN-HAA2HBD-5 AC/DC24 Note: Heater alarm = heater burnout + SSR short detetion + SSR overurrent Note: For option modules (AA), see " modules E53-_ N" on page 2 Aessories (Order Separately) USB-infrared Conversion Cable odel E58-CIFIR Waterproof Paking Connetable models E5AN-H E5EN-H odel Y92S-P4 Y92S-P5 USB-Serial Conversion Cable Note: The Waterproof Paking is inluded with the Controller. Terminal Cover odel E58-CIFQ Current Transformers (CTs) Hole diameter odel 5.8 dia. E54-CT 2. dia. E54-CT3 Connetable models odel E5AN-H E5EN-H E53-COV6 Note: The Terminal Cover omes with the E5CN-@@@-5 models. C-Thermo Support Software odel EST2-2C-V4 4 Advaned Digital Temperature Controller E5AN-H/E5EN-H

5 Speifiations Ratings Power supply voltage Operating voltage range Power onsumption Sensor Input impedane Control method Relay Voltage (for driving SSR) Current Control Linear voltage Built-in SSR Auxiliary Event Logi operations Transfer s RSP Relay for position-proportional ontrol Number of s Output speifiations Number of s External ontat speifiations Number of operations Operations Output Setting method Work bit assignment Number of s No D in model number: to 24 VAC, 5/6 Hz D in model number: 24 VAC, 5/6 Hz; 24 VDC 85% to % of rated supply voltage to 24 VAC: 2 VA 24 VAC/VDC: 8.5 VA (24 VAC)/5.5 W (24 VDC) Any of the following an be seleted. Thermoouple: K, J, T, E, L, U, N, R, S, B, W, or PL II Platinum resistane thermometer: Pt or JPt Current : 4 to 2 ma or to 2 ma Voltage : to 5 V, to 5 V, or to V Current : 5 Ω max., Voltage : Ω min. (Use a : onnetion when onneting the ES2-HB.) / ontrol or 2-PID ontrol (with auto-tuning) Output Unit (Install the Output Unit (sold separately).) 75 to 25 VAC, A (resistive load) Relay : Open and lose: SPST-NO, 25 VAC, A (inluding in-rush urrent), eletrial life:, operations min. Potentiometer : ust be between Ω and 2.5 kω for maximum open position. 2 or 3 max. Relay : SPST-NO, 25 VAC, 3 A (resistive load), eletrial life:, operations, minimum appliable load: 5 V, ma 2 (standard) or 4 (with an E53-AKB) Contat : : kω max., : kω min. Non-ontat : : Residual voltage:.5 V max., : Leakage urrent:. ma max. Current flow: Approx. 7 ma per ontat 8 max. Logi operation: Any of the following four patterns an be seleted. The status may be inverted. (A and B) or (C and D), (A or C) and (B or D), A or B or C or D, A and B and C and D (A, B, C, and D are four s.) Delay: delay or delay for the results of the logi operation given above. Setting time: to 9999 s or to 9999 min Output inversion: Possible One work bit per operation Any of The following an be assigned to up to eight work bits (logi operation results): Event operations, auxiliary s, or ontrol s. max. (Depends on model. odels with transfer (F in model number) Output speifiations Current : 4 to 2 ma DC, Load: 6 Ω max., Resolution at 4 to 2 ma: Approx., Number of s Signal type Current : 4 to 2 ma ( impedane: 5 Ω ±%) Analog saling Auray Indiation method Bank swithing Input sampling period Saling of signal to engineering units (EU) 9,999 to 3, (display: 3, max.) (±.2% of FS) ± digit max. 6 ms Set digitally using keys on the front panel or by using the RSP. -segment digital display and individual indiators (7-segments display emulation also possible) Charater height: E5AN-H: PV: 5.8 mm, SV: 9.5 mm, V: 6.8 mm; E5EN-H: PV:.8 mm, SV: 8. mm, V: 5.8 mm Content of 3-level display: PV/SV/V, PV/SV/Bank No., or soak time remain Number of digits: 5 for PV and SV, 4 for V Supported (number of banks: 8) Loal SP, alarm settings, PID sets (PID onstants, V upper limit, V lower limit, et.) anual, heating/ooling ontrol, loop burnout alarm, SP ramp, other alarm funtions, heater burnout detetion, 4% AT, % AT, V limiter, digital filter, self-tuning, temperature shift, run/stop, protetion funtions, Other funtions ontrol / ounter, extration of square root, V hange rate limit, PV/SV status display, logi operations, automati ooling oeffiient adjustment Ambient operating temperature to 55 C (with no ondensation or iing), for 3-year warranty: to 5 C Ambient operating humidity 25% to 85% Storage temperature 25 to 65 C (with no ondensation or iing) Advaned Digital Temperature Controller E5AN-H/E5EN-H 5

6 Input Ranges Thermoouple/Platinum Resistane Thermometer (Fully Universal Inputs) Temperature range ( C) Input type Platinum resistane thermometer Thermoouple Name Pt JPt K J T E L U N R S B W PL II 4 to 2 m A Analog Usable in the following ranges by saling: to 324, to 324., to 324., or to Setting number to 2 m A to 5V to 5V to V Shaded settings are the default settings. The appliable standards for the types are as follows: K, J, T, E, N, R, S, B: JIS C , IEC 584- L: Fe-CuNi, DIN U: Cu-CuNi, DIN W: W5Re/W26Re, AST E JPt: JIS C , JIS C Pt: JIS C , IEC 75 PL II: Aording to Platinel II eletromotive fore harts from BASF (previously Engelhard) 6 Advaned Digital Temperature Controller E5AN-H/E5EN-H

7 Alarm Outputs Eah alarm an be independently set to one of the following 5 alarm types. The default is 2: Upper limit. Auxiliary s are alloated for alarms. delays and delays ( to 999 s) an also be speified. Note: For models with heater burnout, SSR failure, and heater overurrent detetion, alarm will be an OR of the alarm seleted from the following alarm types and the alarms for heater burnout, SSR failure, and heater overurrent. To only a heater burnout alarm, SSR failure alarm, and heater overurrent alarm for alarm, set the alarm type to (i.e., no alarm funtion). Set value Alarm type Alarm funtion Upper- and lowerlimit 2 Upper limit 3 Lower limit Upper- and lowerlimit range Upper- and lowerlimit with standby sequene 5 Upper-limit with standby sequene Lower-limit with standby sequene Absolute-value upper-limit Absolute-value lower-limit Absolute-value upper-limit with standby sequene Absolute-value lower-limit with standby sequene LBA (for alarm only) PV hange rate alarm RSP absolute value upper limit 6 RSP absolute value lower limit 6 Alarm operation When is positive Output L L L SP SP SP SP SP SP SP H H H When is negative SP SP SP SP.With set values, 4 and 5, the upper and lower limit values an be set independently for eah alarm type, and are expressed as L and H. 2. Set value:, Upper- and lower-limit alarm Case L H SP H <, L > H < L Case 2 SP L H H >, L < H > L 3. Set value: 4, Upper- and lower-limit range Case L H SP H <, L > H < L Case 2 SP L H H >, L < H > L Case 3 (Always ) 4. Set value: 5, Upper- and lower-limit with standby sequene For Upper- and Lower-Limit Alarm Desribed Above Case and 2 Always when the upper-limit and lower-limit hysteresis overlaps. Case 3: Always 5. Set value: 5, Upper- and lower-limit with standby sequene Always when the upper-limit and lower-limit hysteresis overlaps. 6. Displayed when there is a remote SP. H H SP L SP SP H L L Case 3 (Always ) H H SP L SP SP H L L H <, L < H <, L > H L H >, L < H L H <, L < H <, L > H L H >, L < H L Advaned Digital Temperature Controller E5AN-H/E5EN-H 7

8 Charateristis Thermoouple: (±.% of indiated value or ± C, whihever is greater) ± digit max. Platinum resistane thermometer: (±.% of indiated value or ±.5 C, whihever is greater) ± digit max. Indiation auray Analog : ±.% FS ± digit max. CT : ±5% FS ± digit max. Potentiometer : ±5% FS ± digit max. Transfer auray ±.3% FS max. Influene of temperature 2 Influene of voltage 2 Input sampling period Hysteresis Thermoouple (R, S, B, W, PL II): (±% of PV or ± C, whihever is greater) ± digit max. Other thermoouple : (±% of PV or ±4 C, whihever is greater) ± digit max. 3 Platinum resistane thermometer: (±% of PV or ±2 C, whihever is greater) ± digit max. Analog : (±%FS) ± digit max. 6 ms Temperature :. to 324. C or F (in units of. C or F) Analog :.% to 99.99% FS (in units of.% FS) Proportional band (P) Temperature :. to 324. C or F (in units of. C or F) Analog :.% to 999.9% FS (in units of.% FS) Integral time (I). to 324. s (in units of. s) Derivative time (D). to 324. s (in units of. s) Control period.5, to 99 s (in units of s) anual reset value. to.% (in units of.%) Alarm setting range Affet of signal soure resistane Insulation resistane 9999 to 324 (deimal point position depends on type) Thermoouple:. C/Ω max. ( Ω max.) Platinum resistane thermometer:. C/Ω max. ( Ω max.) 2 Ω min. (at 5 VDC) Dieletri strength 2,3 VAC, 5 or 6 Hz for min (between terminals with different harge) Vibration alfuntion to 55 Hz, 2 m/s 2 for min eah in, Y, and Z diretions resistane Destrution to 55 Hz,.75-mm single amplitude for 2 hrs eah in, Y, and Z diretions Shok alfuntion m/s 2, 3 times eah in, Y, and Z diretions resistane Destrution 3 m/s 2, 3 times eah in, Y, and Z diretions Weight E5AN-H E5EN-H Degree of protetion emory protetion Setup Tool Setup Tool port Standards EC Approved standards Conformed standards Controller: Approx. 3 g, ounting Braket: Approx. g Controller: Approx. 26 g, ounting Braket: Approx. g Front panel: IP66, Rear ase: IP2, Terminals: IP Non-volatile memory (number of writes:,, times) C-Thermo version 4. or higher Provided on the bottom of the E5AN-H and E5EN-H. An E58-CIFQ USB-Serial Conversion Cable is required to onnet the omputer to the E5AN-H and E5EN-H. Provided on the front of the E5AN-H and E5EN-H. An E58-CIFIR USB-infrared Conversion Cable is required to onnet the omputer to the E5AN-H or E5EN-H. 4 UL 6-, CSA C22.2 No. - EN 6- (IEC 6-): Pollution level 2, overurrent ategory II EI: EN 6326 Radiated Interferene Eletromagneti Field Strength: EN 55 Group, lass A Noise Terminal Voltage: EN 55 Group, lass A ES: EN 6326 ESD Immunity: EN Eletromagneti Field Immunity: EN Burst Noise Immunity: EN Conduted Disturbane Immunity: EN Surge Immunity: EN Power Frequeny agneti Field Immunity: EN Voltage Dip/Interrupting Immunity: EN The indiation auray of K thermoouples in the 2 to 3 C range, T and N thermoouples at a temperature of C max., and U and L thermoouples at any temperatures is ±2 C ± digit max. The indiation auray of the B thermoouple at a temperature of 4 C max. is not speified. The indiation auray of B thermoouples in the 4 to 8 C range is ±3 C max. The indiation auray of the R and S thermoouples at a temperature of 2 C max. is ±3 C ± digit max. The indiation auray of W thermoouples is ±.3% of PV or ±3 C, whihever is greater, ± digit max. The indiation auray of PL II thermoouples is ±.3% of PV or ±2 C, whihever is greater, ± digit max. 2. Ambient temperature: C to 23 C to 55 C, Voltage range: 5% to % of rated voltage 3. K thermoouple at C max.: ± C max. 4. External ommuniations (RS-232C, RS-485, or RS-422) and able ommuniations for the Setup Tool an be used at the same time. 8 Advaned Digital Temperature Controller E5AN-H/E5EN-H

9 USB-Serial Conversion Cable Appliable OS Appliable software Windows 2, P, or Vista Thermo ini, C-Thermo version 4. or higher Appliable models E5AN/E5EN/E5CN/E5CN-U/ E5AN-H/E5EN-H/E5CN-H USB interfae standard Conforms to USB Speifiation.. DTE speed Connetor speifiations Power supply Power supply voltage Current onsumption Ambient operating temperature 384 bps Computer: USB (type A plug) Temperature Controller: Setup Tool port (on bottom of Controller) Bus power (Supplied from USB host ontroller.) 5 VDC 7 ma Ambient operating humidity % to 8% to 55 C (with no ondensation or iing) Storage temperature 2 to 6 C (with no ondensation or iing) Storage humidity % to 8% Altitude Weight Note: A driver must be installed in the personal omputer. Refer to installation information in the operation manual for the Conversion Cable. Communiations Speifiations Transmission line onnetion method Communiations Synhronization method Protool Baud rate Transmission ode Data bit length Stop bit length Error detetion Flow ontrol Interfae Retry funtion Communiations buffer Communiations response wait time 2, m max. Approx. g RS-485, RS-422: ultipoint RS-232C: Point-to-point RS-485 (two-wire, half duplex) RS-422 (four-wire, half duplex) or RS-232C Start-stop synhronization CompoWay/F, SYSWAY, or odbus 2, 24, 48, 96, 92, 384, or 576 bps ASCII (CompoWay/F, SYSWAY) RTU (odbus) 7 or 8 bits or 2 bits Vertial parity (none, even, odd) Frame hek sequene (FCS) with SYSWAY Blok hek harater (BCC) with CompoWay/F or CRC-6 odbus None RS-485, RS-422, or RS-232C None 27 bytes to 99 ms Default: 2 ms Note: The baud rate, data bit length, stop bit length, and vertial parity an be individually set using the Communiations Setting. Current Transformer (Order Separately) Ratings Dieletri strength, VAC for min Vibration resistane 5 Hz, 98 m/s 2 Weight E54-CT: Approx..5 g, E54-CT3: Approx. 5 g Aessories (E54-CT3 only) Armatures (2) Plugs (2) USB-Infrared Conversion Cable Appliable OS Appliable software Appliable models Windows 2, P, or Vista Thermo ini, C-Thermo version 4. or higher E5AN-H/E5EN-H USB interfae standard Conforms to USB Speifiation.. DTE speed Connetor speifiations Power supply Power supply voltage Current onsumption Ambient operating temperature 384 bps Computer: USB (type A plug) Temperature Controller: Infrared port (on front of Controller) Bus power (Supplied from USB host ontroller.) 5 VDC 8 ma Ambient operating humidity % to 8% to 55 C (with no ondensation or iing) Storage temperature 2 to 6 C (with no ondensation or iing) Storage humidity % to 8% Altitude Weight 2, m max. Approx. 3 g (with mounting adaptor) Note: A driver must be installed in the personal omputer. Refer to installation information in the operation manual for the Conversion Cable. Heater Burnout Alarms, SSR Failure Alarms, and Heater Overurrent Alarms CT (for heater urrent detetion) aximum heater urrent Input urrent indiation auray Heater burnout alarm setting range SSR failure alarm setting range 2 Heater overurrent alarm setting range 3 odels with detetion for single-phase heaters: One odels with detetion for single-phase or three-phase heaters: Two s 5 A AC ±5% FS ± digit max.. to 49.9 A (in units of. A) inimum detetion time: ms. to 49.9 A (in units of. A) inimum detetion time: ms. to 49.9 A (in units of. A) inimum detetion time: ms. For heater burnout alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is lower than the set value (i.e., heater burnout detetion urrent value). 2. For SSR failure alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is higher than the set value (i.e., SSR failure detetion urrent value). 3. For heater overurrent alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is higher than the set value (i.e., heater overurrent detetion urrent value). Advaned Digital Temperature Controller E5AN-H/E5EN-H 9

10 Eletrial Life Expetany Curve for Relays (Referene Values) Life ( 4 operations) E5AN-H/E5EN-H 25 VAC, 3 VDC (resistive load) osφ = SSR Outputs (OUT/OUT2) Ratings Rated load voltage: 75 to 25 VAC Rated load urrent: A (resistive load) Note:. The load urrent must be within the derating urve. 2. There is no zero-ross funtion. Derating Curve for SSR Outputs (Referene Values) Load urrent I (A) OUT/OUT Condition B Swithing urrent (A).5.25 Condition A Ambient temperature ( C) Condition A: SSR s % Condition B: SSR s 5% with 2-s ontrol yle Advaned Digital Temperature Controller E5AN-H/E5EN-H

11 External Connetions A voltage (ontrol, for driving SSR) is not eletrially insulated from the internal iruits. When using a grounding thermoouple, do not onnet any of the ontrol terminals to ground. If the ontrol terminals are onneted to ground, errors will our in the measured temperature values as a result of leakage urrent. The voltage (ontrol 2, for driving SSR) has basi insulation provided for the internal iruit Controllers Option Units Communiations to 24 VAC 24 VAC/VDC (no polarity) Control s, 2 Output Unit Control s, 2 Relay Outputs 25 VAC, 5 A (resistive load) SSR Outputs 75 to 25 VAC, A (resistive load) odels with Positionproportional Control 25 VAC, A (inluding inrush urrent) Auxiliary s, 2 Relay SPST-NO, 25 VAC, 3 A (resistive load) Input power supply Control Control 2 Auxiliary 2 Auxiliary E53-EN RS-232C CT2 CT CT2 D T USE D T USE SD RD SG DO NOT USE DO NOT USE Potentiometer O W C D T USE A B B D T USE E53-EN2 RS D T USE RDB RDA SG SDB SDA Auxiliary 3 V D T USE ma D T USE t/ Pt V ma E53-EN3 RS B ( ) A ( ) DO NOT USE B ( ) A ( ) Auxiliary 3 E53-AKB EV2 Relay SPDT, 25 VAC, 3 A (resistive load) Event Inputs EV A heater burnout alarm, SSR failure, heater overurrent alarm, or alarm is sent to the to whih the alarm funtion is assigned. EV3 EV D T USE Transfer 28 4 to 2 ma DC (Load: 6 max.) 29 Remote SP 3 4 to 2 ma DC Note: Wire all voltage terminals orretly. The Controller may fail if voltage terminals are wired inorretly. Advaned Digital Temperature Controller E5AN-H/E5EN-H

12 Nomenlature E5AN-H E5EN-H Temperature unit Operation indiators Operation indiators SUB SUB2 SUB3 HA PV No. display Temperature unit SUB SUB2 HA SUB3 PV No. display SV No.2 display SV No.2 display RSP OUT RSP STOP OUT2 CW ANU V No.3 display Operation indiators OUT STOP OUT2 CW ANU V No.3 display Programmable Funtion Key/ Auto/anual Key PF A/ E5AN-H Ir Up Key Down Key ode Key Key E5EN-H Ir PF A/ Up Key Programmable Funtion Key/ Auto/anual Key Key ode Key Down Key Dimensions (Unit: mm) E5AN-H ounted Separately Group ounted (96 number of units 3.5) min Group mounting does not allow waterproofing. Reommended panel thikness is to 8 mm. Group mounting is not possible in the vertial diretion. (aintain the speified mounting spae between Controllers.) To mount the Controller so that it is waterproof, insert the waterproof paking onto the Controller. When two or more Controllers are mounted, make sure that the surrounding temperature does not exeed the allowable operating temperature speified in the speifiations. Group mounting is not possible if an SSR is used for ontrol or 2 and the E53-C3N or E53-C3DN Output Unit is used. For these ombinations, maintain the following mounting spae between Controllers. Waterproof Paking (Aessory) ounting Braket (Aessory) Terminal Cover (E53-COV6) (Aessory) Crimp terminal size: min min. 2 Advaned Digital Temperature Controller E5AN-H/E5EN-H

13 E5EN-H ounted Separately Group ounted (48 number of units 2.5) min. Group mounting does not allow waterproofing Reommended panel thikness is to 8 mm. Group mounting is not possible in the vertial diretion. (aintain the speified mounting spae between Controllers.) When two or more Controllers are mounted, make sure that the surrounding temperature does not exeed the allowable operating temperature speified in the speifiations. Group mounting is not possible if an SSR is used for ontrol or 2 and the E53-C3N or E53-C3DN Output Unit is used. For these ombinations, maintain the following mounting spae between Controllers min Waterproof Paking (Aessory) ounting Braket (Aessory) Terminal Cover (E53-COV6) (Aessory) Crimp terminal size: min. Advaned Digital Temperature Controller E5AN-H/E5EN-H 3

14 Aessories (Order Separately) USB-Infrared Conversion Cable E58-CIFIR USB-Infrared Conversion Cable (2,) USB onnetor (type A plug) 4.6 dia. LED indiator: RD LED indiator: SD 7.8 With ounting Adapter Conneted ounting Adapter ounting Adapter (Aessory) (75) 23. USB-Serial Conversion Cable E58-CIFQ (2,) 25 LED indiator: SD,765 USB onnetor (type A plug) LED indiator: RD Serial onnetor Terminal Covers E53-COV6 (Six Covers provided.) Advaned Digital Temperature Controller E5AN-H/E5EN-H

15 Waterproof Paking Y92S-P4 (for DIN 96 96) Y92S-P5 (for DIN 48 96) Order the Waterproof Paking separately if it beomes lost or damaged. The Waterproof Paking an be used to ahieve an IP66 degree of protetion. (Deterioration, shrinking, or hardening of the waterproof paking may our depending on the operating environment. Therefore, periodi replaement is reommended to ensure the level of waterproofing speified in IP66. The time for periodi replaement depends on the operating environment. Be sure to onfirm this point at your site. Consider one year a rough standard. OR shall not be liable for the level of water resistane if the ustomer does not perform periodi replaement.) The Waterproof Paking does not need to be attahed if a waterproof struture is not required. Current Transformers E54-CT dia E54-CT Thru-urrent (Io) vs. Output Voltage (Eo) (Referene Values) aximum ontinuous heater urrent: 5 A (5/6 Hz) Number of windings: 4±2 Winding resistane: 8±2 Ω E54-CT Two, 3.5 dia dia. 2 dia. 9 Output voltage (Eo) V (r.m.s.) V 5 Hz mv μv kω Ω RL = Ω Distortion fator % 3% % E54-CT3 Aessory Armature Approx. 3 dia. Plug Two, 3 (depth 4) 5 3 Connetion Example Armature Plug Lead ma, A Thru-urrent (Io) A (r.m.s.) E54-CT3 Thru-urrent (Io) vs. Output Voltage (Eo) (Referene Values) aximum ontinuous heater urrent: 2 A (5/6 Hz) (aximum ontinuous heater urrent for an OR Temperature Controller is 5 A.) Number of windings: 4±2 Winding resistane: 8±.8 Ω Output voltage (Eo) V (r.m.s.) V 5 Hz mv kω 5 Ω Ω 5 Ω RL = Ω Distortion fator % 3% % Approx. 6 dia. μv (22) ma, A Thru-urrent (Io) A (r.m.s.) Advaned Digital Temperature Controller E5AN-H/E5EN-H 5

16 6 Advaned Digital Temperature Controller E5AN-H/E5EN-H

17 Operation E5EN-H / E5AN-H Start in manual mode. Power Start in automati mode. anual mode Press the O Key or the PF Key for at least s. 4 3 anual Control a-m Press the O Key for at least 3 s while a-m is displayed. (a-m will flash after st seond.) Press the PF Key for at least s. 4 Control stops. Press the O Key for at least s. Operation Press the O Key for at least s. PF Key 5 Initial Setting Press the O Key less than s. Press the O Key less than s. PID Setting onitor/setting Item 25.. Advaned Funtion Setting Press the O Key less than s. Input password while amov is displayed. (Set value 69) Adjustment Press the O Key for at least 3 s. (Display will flash after st seond.) Communiations Setting Press the O Key for less than s. Press the O Key less than s. Bank Setting PF Key 5 Press the O + Keys for at least 3 s. (Display will flash after st seond.) 25.. Protet Note: The time taken to move to the protet level an be adjusted by hanging the ove to protet level time setting. Press the O+ Keys for at least s. Input password. Control in progress. You an return to the operation level by exeuting a software reset. 2. It is not possible to move to other levels from the alibration level by operating the keys on the front panel. It an be done only by first turning the power. 3. From the manual ontrol level, key operations an be used to move to the operation level only. 4. When the PF Setting parameter is set to A- for a Controller with a PF Key (E5AN-H/E5EN-H). 5. When the PF Setting parameter is set to PFDP for a Controller with a PF Key (E5AN-H/E5EN-H) Error Displays (Troubleshooting) When an error ours, the No. display shows the error ode. Take neessary measure aording to the error ode, referring the table below. No. display eaning Ation s.err (S. Err) e333 (E333) e (E) Input error A/D onverter error emory error Calibration Control stopped hange Chek the wiring of s for miswiring, disonnetions, and short-iruits and hek the type. Turn the power then bak again. If the display remains the same, the ontroller must be repaired. If the display is restored to normal, then a probable ause an be external noise affeting the ontrol system. Chek for external noise. Turn the power then bak again. If the display remains the same, the ontroller must be repaired. If the display is restored to normal, then a probable ause an be external noise affeting the ontrol system. Chek for external noise. Not displayed for some models Control Status at error Alarm Note: If the value exeeds the display limit (-9999 to 324), though it is within the ontrol range, will be displayed under and above 324. Under these onditions, ontrol and alarm will operate normally. For details on the ontrol range, refer to the E5CN-H/E5AN-H/E5EN-H Digital Controllers User's anual Advaned Type (Cat. No. H57). These errors are displayed only when the PV/SP is displayed. Errors are not displayed for other displays. 2 Operates as above the upper limit. Advaned Digital Temperature Controller E5AN-H/E5EN-H 7

18 E5EN-H / E5AN-H Some parameters are not displayed depending on the model of the Controller and parameter settings. For details, refer to the E5CN-H/E5AN-H/ E5EN-H Digital Controllers User's anual Advaned Type (Cat. No. H57). Power anual Control Protet Operation Adjustment Bank Setting PID Setting onitor/setting Item Initial Setting Communiations Setting Advaned Funtion Setting PID Setting Press the O Key less than s. Bank Setting Press the O Key less than s. Press the O Key less than s. Display PID Seletion d. pid PID d. pid PID2 2 d. pid 3 PID3 Display Bank Seletion d.bnk Bank d.bnk Bank d. d.bnk 2 Bank2 d.pid 8 PID8 d.bnk 7 Bank7. p 8.. i 233..d 4..olh 5.. oll -5..aut 32..s.. lba 8.p PID 8 Proportional Band 8. 8.i PID 8 Integral Time d PID 8 Derivative Time 4. 8.ol h PID 8 V Upper Limit ol l PID 8 V Lower Limit aut PID 8 Automati Seletion 32. Range Upper Limit 8. s PID 8 Cooling Coeffiient. 8.lba PID 8 LBA Detetion Time.lsp..pid. s p r.a -.. a h..a l..a -2.. a 2h.. a 2l..a -3.. a 3h..a 3l.. s o k.w t b 7.lsp. 7.pid 7.s p r Bank 7 SP of f Ramp Set Value 7.a - Bank 7. Alarm Value Bank 7 7. a h Alarm Value. Upper Limit Bank 7 7.a l. Bank 7 SP Bank 7 PID Set No. Alarm Value Lower Limit Set either of these parameters 7.a -2 Bank 7. Alarm Value 2 Bank 7 7. a 2h Alarm Value. Upper Limit 2 7. a 2l. 7.a -3 Bank 7. Alarm Value 3 Bank 7 7. a 3h Alarm Value. Upper Limit 3 Bank 7 Alarm Value Lower Limit 2 Bank 7 7. a 3l Alarm Value. Lower Limit 3 Set either of these parameters Set either of these parameters 7. s o k Bank 7 Soak Time 7. w t b Bank 7 Wait Band of f 8 Advaned Digital Temperature Controller E5AN-H/E5EN-H

19 Power Press the PF Key for at least s. Starting in manual mode. anual Control 25.. PV/V PID Control only Press the O Key or the PF Key for at least s. Starting in automati mode. Adjustment Press the O Key less than s. Operation Press the O and Keys for at least 3 s. l.adj at mwt irda spmd lsp t Heater Current. Value onitor hb Heater Burnout. Detetion o Heater Overurrent 5. Detetion t2. hb2. o2 5. lr. hs 5. lr2. hs2 5. ins. insh Upper Limit Temperature. Input Shift Value 2-point shift insl. Adjustment Display Displayed only one when entering adjustment level. AT Exeute/Canel Communiations Writing Infrared Communiations Use SP ode Heater Current 2 Value onitor Heater Burnout Detetion 2 Heater Overurrent Detetion 2 Leakage Current onitor HS Alarm Leakage Current 2 onitor HS Alarm 2 Temperature Input Shift -point shift Lower Limit Temperature Input Shift Value Set either of these parameters. p 8. i 233. d 4. -s. -db. of-r 5. hys. hys. soak wt-b mv-s. mv-e. sprt ol-h 5. ol-l -5. orl. db Position Proportional Dead Band 2. o-h.8 sqrp. Proportional Band Integral Time Derivative Time PID settings Cooling Coeffiient Heating/ooling Dead Band anual Reset Value Clear the set during stabilization of P or PD ontrol. Hysteresis (Heating) Hysteresis settings Hysteresis (Cooling) Soak Time Wait Band V at Stop V at PV Error SP Ramp Set Value V Upper Limit V Lower Limit V Change Rate Limit Open/Close Hysteresis Extration of Square Root Low-ut Point Press the O Key for at least 3 s a-m bank rsp. sp-m. t Heater Current Value. onitor t2 Heater Current 2 Value. onitor lr. lr2. prst rset sktr 25. PF Key 2 Proess Value Added when Additional PV display is. Proess Value/ Set Point Auto/anual Swith PID ontrol only. Added when auto/manual selet addition is. Bank No. Remote SP onitor Set Point During SP Ramp Leakage Current onitor Leakage Current 2 onitor Program Start Soak Time Remain onitor/setting Item Display. PF PF r-s run al-. alh. all. al-2. al2h. al2l. al-3. al3h. al3l. o. -o. RUN/STOP Alarm Value Alarm Value Upper Limit Alarm Value Lower Limit Alarm Value 2 Alarm Value Upper Limit 2 Alarm Value Lower Limit 2 Alarm Value 3 Alarm Value Upper Limit 3 Alarm Value Lower Limit 3 v-m Valve Opening onitor. PF Set either of these parameters. Set either of these parameters. Set either of these parameters. V onitor (Heating) V onitor (Cooling) onitor/setting Item (E5AN-H/E5EN-H only) onitor/setting Item Display 4 onitor/setting Item Display 2 onitor/setting Item Display 5 Note: The monitor/setting items to be displayed is set in the onitor/setting Item to 5 parameters (advaned funtion setting level). Press the O and Keys for at least s. onitor/setting Item Display 3 PF PF Key 2. When the PF Setting parameter is set to A- for a Controller with a PF Key (E5AN-H/E5EN-H). 2. When the PF Setting parameter is set to PFDP for a Controller with a PF Key (E5AN-H/E5EN-H). Advaned Digital Temperature Controller E5AN-H/E5EN-H 9

20 Press the O Key for at least s. Press the O Key for at least 3 s. Other than the Auto/anual Swith display Press the O Key less than s. Initial Setting pmov oapt ipt wtpt pfpt pmsk on prlp Protet The time taken to move to the protet level an be adjusted by hanging the "ove to protet level time" setting. ove to Protet : Displayed only when a password is set. Restrits moving to protet level. Operation/Adjustment Protet: Restrits displaying and modifying menus in operation, adjustment, and manual ontrol levels. Initial Setting/ Communiations Protet: This protet level restrits movement to the initial setting, ommuniations setting, and advaned funtion setting levels. Setting Change Protet: Protets hanges to setups by operating the front panel keys. PF Key Protet Restrits PF key operation (E5AN-H/E5EN-H only) Parameter ask Enable: Displayed only when a parameter mask is set. Password to ove to Protet : Password setting Press the O Key less than s. Communiations Setting Displayed only for models with ommuniations. Changes are effetive after yling power or after a software reset. psel wf u-no bps 9.6 len 7 sbit 2 prty even sdwt 2 Protool Setting: Swithes between CompoWay/F (SYSWAY) and odbus. Communiations Unit No. Communiations Baud Rate CompoWay/F (SYSWAY) only Communiations Data Length Communiations Stop Bits Communiations Parity Send Data Wait Time in-t 5 in-h in-l dp d-u sl-h 3. sl-l -2. ntl pid Standard or s-h Heating/Cooling stnd ST (Self-tuning) st on ptrn pbnk 7 p 2 -p 2 orev or-r alt 2 alh.2 Input Type Saling Upper Limit Saling Lower Limit Deimal Point For type of analog Temperature Unit C, F For type of temperature SP Upper Limit Limit the set point SP Lower Limit PID / For type of temperature, standard ontrol, or PID Program Pattern Valid Program Bank When assigning PID or ontrol to / Control Period (Heating) Set the / yle. Control Period (Cooling) Diret/Reverse Operation Alarm Type Alarm Hysteresis alt2 2 alh2.2 alt3 2 alh3.2 tr-t tr-h Transfer Output Upper Limit. tr-l. o-t 4-2 ev-b ev- Event Input Assignment none ev-2 stop ev-3 none ev-4 Event Input Assignment 4 none lfl flot alb mot 3 sqr Extration of Square Root Enable amov Alarm 2 Type Alarm 2 Hysteresis Alarm 3 Type Alarm 3 Hysteresis Transfer Output Type Linear Transfer Output Lower Limit Linear Current Output Linear Bank Numbers Used Event Input Assignment 2 Event Input Assignment 3 Closed/Floating otor Calibration Travel Time ove to Advaned Funtion Setting : Displayed when initial setting/ ommuniations protet is set to. ove by setting password ( 69). 2 Advaned Digital Temperature Controller E5AN-H/E5EN-H

21 Power anual Control Protet Operation Adjustment Bank Setting PID Setting onitor/setting Item Initial Setting Communiations Setting Advaned Funtion Setting Press the O Key for at least s. Advaned Funtion Setting init spru m rest a sbn n-o sb2n n-o sb3n n-o hbu on hbl hbh Heater Burnout Hysteresis. st-b 5. α alfa.65 at-g. at-h.8 lma 2. inf. pvad Parameter Initialization SP Ramp Time Unit Standby Sequene Reset Auxiliary Output Open in Alarm Auxiliary Output 2 Open in Alarm Auxiliary Output 3 Open in Alarm HB / Heater Burnout Lath ST Stable Range AT Calulated Gain AT Hysteresis Limit Cyle V Amplitude Input Digital Filter Additional PV Display o-dp ret alt a2lt a3lt prlt 3 sero j on rlrv olr red pv-b 5. aon a2on a3on aof Alarm Delay a2of a3of V Display Automati Display Return Time Alarm Lath Alarm 2 Lath Alarm 3 Lath ove to Protet Time Input Error Output Cold Juntion Compensation ethod B Command Logi Swithing PV Change Color PV Stable Band Alarm Delay Alarm 2 Delay Alarm 3 Delay Alarm 2 Delay Alarm 3 Delay istp ins mvse amad on rt hsu on hsl hsh. lba out o out2 Control Output 2 Assignment none rspu rsph Remote SP Upper Limit 3. rspl -2. sptr rseo pidi pv pidh.5 lbal LBA p-db 8.. lbab manl LBA Band 3. sub alm sub2 Auxiliary Output 2 Assignment alm2 sub3 alm3 sel on t-u m Input Shift Type V at Stop and Error Addition Auto/anual Selet Addition RT HS Alarm Use HS Alarm Lath HS Alarm Hysteresis LBA Detetion Time Control Output Assignment Auxiliary Output Assignment Auxiliary Output 3 Assignment (E5AN/E5EN-H only) Charater Selet Soak Time Unit alsp sp-m pmvd pvrp 7 sa ou on ol Heater Overurrent Lath Heater Overurrent oh Hysteresis. pf a-m Alarm SP Seletion Remote SP Enable Remote SP Lower Limit SP Traking Remote SP Input Error Output PID Set Automati Seletion Data PID Set Automati Seletion Hysteresis PV Dead Band anual V Limit Enable Diret Setting of Position Proportional V PV Rate of Change Calulation Period Automati Cooling Coeffiient Adjustment Heater Overurrent Use PF Setting pfd pfd2 pfd3 pfd4 pfd5 spdp 4 odsl o pvdp on pvst svst d.ref.25 ram ra2m ra ra2 ra mov onitor/setting Item onitor/setting Item 2 onitor/setting Item 3 onitor/setting Item 4 onitor/setting Item 5 "PV/SP" Display Sreen Seletion V Display Seletion PV Deimal Point Display PV Status Display Funtion SV Status Display Funtion Display Refresh Period Control Output / Count onitor Control Output 2 / Count onitor Control Output / Count Alarm Set Value Control Output 2 / Count Alarm Set Value / Counter Reset ove to Calibration Advaned Digital Temperature Controller E5AN-H/E5EN-H 2

22 Safety Preautions!CAUTI Do not touh the terminals while power is being supplied. Doing so may oasionally result in minor injury due to eletri shok. Do not allow piees of metal, wire lippings, or fine metalli shavings or filings from installation to enter the produt. Doing so may oasionally result in eletri shok, fire, or malfuntion. Do not use the produt where subjet to flammable or explosive gas. Otherwise, minor injury from explosion may oasionally our. Do not leave the able for the Support Software onneted to the produt. alfuntion may our due to noise in the able. Do not use the Temperature Controller or Conversion Cable if it is damaged. Doing so may oasionally result in minor eletri shok or fire. Never disassemble, modify, or repair the produt or touh any of the internal parts. inor eletri shok, fire, or malfuntion may oasionally our. CAUTI - Risk of Fire and Eletri Shok a) This produt is UL listed as Open Type Proess Control Equipment. It must be mounted in an enlosure that does not allow fire to esape externally. b) ore than one disonnet swith may be required to de-energize the equipment before serviing the produt. ) Signal s are SELV, limited energy. d) Caution: To redue the risk of fire or eletri shok, do not interonnet the s of different Class 2 iruits. 2 If the relays are used past their life expetany, ontat fusing or burning may oasionally our. Always onsider the appliation onditions and use the relays within their rated load and eletrial life expetany. The life expetany of relays varies onsiderably with the load and swithing onditions. Tighten the terminal srews to between.74 and.9 N m. 3 Loose srews may oasionally result in fire. Set the parameters of the produt so that they are suitable for the system being ontrolled. If they are not suitable, unexpeted operation may oasionally result in property damage or aidents. A malfuntion in the produt may oasionally make ontrol operations impossible or prevent alarm s, resulting in property damage. To maintain safety in the event of malfuntion of the produt, take appropriate safety measures, suh as installing a monitoring devie on a separate line. A semiondutor is used in the setion of long-life relays. If exessive noise or surge is impressed on the terminals, a short-iruit failure is likely to our. If the remains shorted, fire will our due to overheating of the heater or other ause. Take measures in the overall system to prevent exessive temperature inrease and to prevent fire from spreading. Do not allow piees of metal or wire uttings to get inside the able onnetor for the Support Software. Failure to do so may oasionally result in minor eletri shok, fire, or damage to equipment. Do not allow dust and dirt to ollet between the pins in the onnetor on the Conversion Cable. Failure to do so may oasionally result in fire. When inserting the body of the Temperature Controller into the ase, onfirm that the hooks on the top and bottom are seurely engaged with the ase. If the body of the Temperature Controller is not inserted properly, faulty ontat in the terminal setion or redued water resistane may oasionally result in fire or malfuntion. When onneting the Control Output Unit to the soket, press it in until there is no gap between the Control Output Unit and the soket. Otherwise ontat faults in the onnetor pins may oasionally result in fire or malfuntion.. An SELV iruit is one separated from the power supply with double insulation or reinfored insulation, that does not exeed 3 V r.m.s. and 42.4 V peak or 6 VDC. 2. A lass 2 power supply is one tested and ertified by UL as having the urrent and voltage of the seondary restrited to speifi levels. 3. The tightening torque for E5CN-U is.5 N m. Preautions for Safe Use Be sure to observe the following preautions to prevent malfuntion or adverse affets on the performane or funtionality of the produt. Not doing so may oasionally result in faulty operation.. This produt is speifially designed for indoor use only. Do not use this produt in the following plaes: Plaes diretly subjet to heat radiated from heating equipment. Plaes subjet to splashing liquid or oil atmosphere. Plaes subjet to diret sunlight. Plaes subjet to dust or orrosive gas (in partiular, sulfide gas and ammonia gas). Plaes subjet to intense temperature hange. Plaes subjet to iing and ondensation. Plaes subjet to vibration and large shoks. 2. Use and store the produt within the rated ambient temperature and humidity. Gang-mounting two or more Temperature Controllers, or mounting Temperature Controllers above eah other may ause heat to build up inside the Temperature Controllers, whih will shorten their servie life. In suh a ase, use fored ooling by fans or other means of air ventilation to ool down the Temperature Controllers. 3. To allow heat to esape, do not blok the area around the produt. Do not blok the ventilation holes on the produt. 4. Be sure to wire properly with orret polarity of terminals. 5. Use the speified size (3.5, width 7.2 mm or less) rimped terminals for wiring. To onnet bare wires to the terminal blok, use stranded or solid opper wires with a gage of AWG24 to AWG4 (equal to a ross-setional area of.25 to 2.8 mm 2 ). (The stripping length is 5 to 6 mm.) Up to two wires of the same size and type or two rimp terminals an be inserted into a single terminal. 6. Do not wire the terminals that are not used. 7. To avoid indutive noise, keep the wiring for the produt s terminal blok away from power ables arry high voltages or large urrents. Also, do not wire power lines together with or parallel to produt wiring. Using shielded ables and using separate onduits or duts is reommended. Attah a surge suppressor or noise filter to peripheral devies that generate noise (in partiular, motors, transformers, solenoids, magneti oils, or other equipment that have an indutane omponent). When a noise filter is used at the power supply, first hek the voltage or urrent, and attah the noise filter as lose as possible to the produt. Allow as muh spae as possible between the produt and devies that generate powerful high frequenies (high-frequeny welders, high-frequeny sewing mahines, et.) or surge. 8. Use this produt within the rated load and power supply. 9. ake sure that the rated voltage is attained within two seonds of turning the power using a swith or relay ontat. If the voltage is applied gradually, the power may not be reset or malfuntions may our..ake sure that the Temperature Controller has 3 minutes or more to warm up after turning the power before starting atual ontrol operations to ensure the orret temperature display. 22 Advaned Digital Temperature Controller E5@N/E5@N-H

23 .When exeuting self-tuning, turn power to the load (e.g., heater) at the same time as or before supplying power to the produt. If power is turned to the produt before turning power to the load, self-tuning will not be performed properly and optimum ontrol will not be ahieved. 2.A swith or iruit breaker must be provided lose to the produt. The swith or iruit breaker must be within easy reah of the operator, and must be marked as a disonneting means for this unit. 3.Always turn the power supply before pulling out the interior of the produt, and never touh nor apply shok to the terminals or eletroni omponents. When inserting the interior of the produt, do not allow the eletroni omponents to touh the ase. 4.Do not use paint thinner or similar hemial to lean with. Use standard grade alohol. 5.Design the system (e.g., ontrol panel) onsidering the 2 seonds of delay that the produt's to be set after power. 6.The may turn when shifting to ertain levels. Take this into onsideration when performing ontrol. 7.The number of EEPRO write operations is limited. Therefore, use RA write mode when frequently overwriting data during ommuniations or other operations. 8.Always touh a grounded piee of metal before touhing the Temperature Controller to disharge stati eletriity from your body. 9.Do not remove the terminal blok. Doing so may result in failure or malfuntion. 2.Control s (for driving SSR) that are voltage s are not isolated from the internal iruits. When using a grounded thermoouple, do not onnet any of the ontrol terminals to ground. (Doing so may result in an unwanted iruit path, ausing error in the measured temperature.) 2.When replaing the body of the Temperature Controller, hek the ondition of the terminals. If orroded terminals are used, ontat failure in the terminals may ause the temperature inside the Temperature Controller to inrease, possibly resulting in fire. If the terminals are orroded, replae the ase as well. 22.Use suitable tools when taking the Temperature Controller apart for disposal. Sharp parts inside the Temperature Controller may ause injury. 23.Before onneting an Output Unit, onfirm the speifiations and thoroughly read relevant information in the datasheet and manual for the Temperature Controller. 24.Chek the orientation of the onnetors on the Conversion Cable before onneting the Conversion Cable. Do not fore a onnetor if it does not onnet smoothly. Using exessive fore may damage the onnetor. 25.Do not plae heavy objet on the Conversion Cable, bend the able past its natural bending radius, or pull on the able with undue fore. 26.Do not onnet or disonnet the Conversion Cable while ommuniations are in progress. Produt faults or malfuntion may our. 27.ake sure that the Conversion Cable's metal omponents are not touhing the external power terminals. 28.Do not touh the onnetors on the Conversion Cable with wet hands. Eletrial shok may result. 29.Before using infrared ommuniations, orretly attah the enlosed ounting Adapter to the able for the Support Software. When onneting the infrared port on the able to the Support Software into the Adapter, insert the onnetor to the speified line. Communiations may not be possible if the onnetor is not onneted properly. Preautions for Corret Use Servie Life. Use the produt within the following temperature and humidity ranges: Temperature: to 55 C (with no iing or ondensation) Humidity: 25% to 85% If the produt is installed inside a ontrol board, the ambient temperature must be kept to under 55 C, inluding the temperature around the produt. 2. The servie life of eletroni devies like Temperature Controllers is determined not only by the number of times the relay is swithed but also by the servie life of internal eletroni omponents. Component servie life is affeted by the ambient temperature: the higher the temperature, the shorter the servie life and, the lower the temperature, the longer the servie life. Therefore, the servie life an be extended by lowering the temperature of the Temperature Controller. 3. When two or more Temperature Controllers are mounted horizontally lose to eah other or vertially next to one another, the internal temperature will inrease due to heat radiated by the Temperature Controllers and the servie life will derease. In suh a ase, use fored ooling by fans or other means of air ventilation to ool down the Temperature Controllers. When providing fored ooling, however, be areful not to ool down the terminals setions alone to avoid measurement errors. easurement Auray. When extending or onneting the thermoouple lead wire, be sure to use ompensating wires that math the thermoouple types. 2. When extending or onneting the lead wire of the platinum resistane thermometer, be sure to use wires that have low resistane and keep the resistane of the three lead wires the same. 3. ount the produt so that it is horizontally level. 4. If the measurement auray is low, hek to see if shift has been set orretly. Waterproofing The degree of protetion is as shown below. Setions without any speifiation on their degree of protetion or those with IP@ are not waterproof. Front panel: IP66 Rear ase: IP2, Terminal setion: IP (E5CN-U: Front panel: IP5, rear ase: IP2, terminals: IP) Operating Preautions. It takes approximately two seonds for the s to turn from after the power supply is turned. Due onsideration must be given to this time when inorporating Temperature Controllers in a sequene iruit. 2. When using self-tuning, turn power for the load (e.g., heater) at the same time as or before supplying power to the Temperature Controller. If power is turned for the Temperature Controller before turning power for the load, self-tuning will not be performed properly and optimum ontrol will not be ahieved. 3. When starting operation after the Temperature Controller has warmed up, turn the power and then turn it again at the same time as turning power for the load. (Instead of turning the Temperature Controller and again, swithing from STOP mode to RUN mode an also be used.) 4. Avoid using the Controller in plaes near a radio, television set, or wireless installing. These devies an ause radio disturbanes whih adversely affet the performane of the Controller. Others. The disk that is inluded with the Conversion Cable is designed for a omputer CD-RO driver. Never attempt to play the disk in a general-purpose audio player. 2. Do not onnet or disonnet the Conversion Cable onnetor repeatedly over a short period of time. The omputer may malfuntion. 3. After onneting the Conversion Cable to the omputer, hek the CO port number before starting ommuniations. The omputer requires time to reognize the able onnetion. This delay does not indiate failure. 4. Do not onnet the Conversion Cable through a USB hub. Doing so may damage the Conversion Cable. 5. Do not use an extension able to extend the Conversion Cable length when onneting to the omputer. Doing so may damage the Conversion Cable. 6. The E5AN-H/E5EN-H use the same port for ommuniations through the infrared port and the Support Software port. Do not attempt to use ommuniations through the Support Software port when the infrared port is being used. Advaned Digital Temperature Controller E5@N/E5@N-H 23