QS Motor Group Controller QSE-CI-4M-D 4-Output AC Motor Controller. Energi Savr NodeTM Unit. seetouchr QS Wallstation. Wireless Communication

Transcription

1 LUTRON LUTRON R Motor Grop Controller E-CI-4M-D 4-Otpt AC Motor Controller Motor Grop Controller The motor grop controller is an interface that provides seamless integration of Qantm and stand-alone systems with AC blinds, shades, lovers, projection screens, or any compatible AC motor. It provides for (4) independently controllable AC raise/ lower otpts from one common AC inpt feed. Featres In stand-alone systems, the motor grop controller's high-voltage otpts for motor loads can be controlled and programmed similar to shades. The otpts can be programmed to be controlled by: GRAFIK Eye shade btton colmns seetoch shade wallstations Pico wireless shade controls (throgh a Sensor Modle) In Qantm systems, the motor grop controller's high-voltage otpts for motor loads are flly programmable throgh the Q-DesignTM Qantm programming software. (Contact Ltron Cstomer Service for availability.) E-CI-4M-D 1,2 N m L N E-CI-4M-D c System Example 4 motor control otpts, 1,5 A each (zones 1-4) (cannot be sed for non-motor loads) seetochr Wallstation Energi Savr NodeTM Unit QantmR Panel GRAFIK EyeR IR Transmitter 230 V~ Control Power Motor Grop Controller Link Wireless Commnication Sensor Modle (M) See Notes below Power Spply Up to 100 total devices IR Eye Pico Wireless Controller (p to 10 per M) Notes (M) Up to for wired inpts total (of any type). Mltiple Ms can be added to increase the nmber of wireless inpts and Pico wireless controllers.

2 Motor Grop Controller E-CI-4M-D 4-Otpt AC Motor Controller Specifications c Inpt Power Inpt voltage: 230 V~ 50/60 Hz 6 A maximm total inpt crrent At standby (no motors being driven), power is less than 1 W Lightning strike protection meets ANSI/IEEE standard Can withstand voltage srges of p to V~ and crrent srges of p to A Otpt Capacity 1,5 A maximm motor load per channel (not for lighting control) Each zone spports only one motor; do not wire motors in parallel Raise and Lower otpts are mechanically interlocked to prevent simltaneosly activating Raise/Lower otpts. Designed to withstand open/close cycles Reglatory Reqirements IEC/EN , EN50428 Ltron Qality Systems registered to ISO CE Other Power Specifications Standby power: V~: 660 mw BTU/hor when flly loaded: 5 Environment Ambient temperatre operating range (inside monting panel): 0 ºC to 40 ºC (32 ºF to 104 ºF) Calibration point maximm: 65 ºC (149 ºF) Srronding air temperatre: T a 65 ºC Relative hmidity: less than 90% non-condensing For indoor se only Terminals Mains Wiring: 1,0 to 4,0 mm 2 (18 to 12 AWG) Zone Wiring: 1,0 to 4,0 mm 2 (18 to 12 AWG) Link Wiring: See Wiring: Link Monting Use an IP20 (minimm) rated consmer panel or breaker panel with integrated DIN rail Width = 9 DIN modles (161,7 mm/6,4 in) Link Limits A link can have p to 100 zones (otpts) and 100 devices Each motor grop controller conts as 4 zones (otpts) and 1 device on the link The motor grop controller (E-CI-4M-D) nit does not spply or consme power draw nits. When sing accessories (sch as a keypad or a IR Eye, an additional 24 V- power spply or an Energi Savr NodeTM mst provide power and/or power draw nits. For more information on Power Draw Units, see "Power Draw Units on the Link", Ltron PN , at Ot of Box Fnctionality Defalt fnctionality that the nit will present when first installed: Unprogrammed shade keypads and/or Pico wireless controls will raise/lower all 4 otpts when connected to a Sensor Modle (M) Normal Mode Operation Zone btton selects the desired zone; raise/lower bttons control the selected zone Spports,, and Unaffected presets only; all other presets are ignored Does not spport shade grops or areas Does not spport discrete shade levels Does not spport scenes Configrable Parameters Minimm On time (also called Jog Time): the minimm time for which the Raise/Lower relay will be trned on. Configrable from 80 ms to 3520 ms in 80 ms increments Defalt: 80 ms Interlock delay: the time both relays are de-energized while switching from Raise to Lower, or from Lower to Raise Configrable to 320 ms, 560 ms, or 960 ms Defalt: 320 ms Maximm On time (also called Travel Time or Time to Off): after this time, the relay is trned off as a precation. Configrable from 10 seconds to 450 seconds in 10-seond increments Defalt: 80 seconds

3 Motor Grop Controller E-CI-4M-D 4-Otpt AC Motor Controller Mechanical Dimensions c E-CI-4M-D 1,2 N m L N 89,7 mm (3,5 in) 161,7 mm (6,4 in) (Eqal to 9 DIN modles) 60,6 mm (2,4 in)

4 Motor Grop Controller E-CI-4M-D 4-Otpt AC Motor Controller Control Options Operation with GRAFIK Eye control nit Each motor grop controller otpt can be assigned independently to any shade btton colmn on a GRAFIK Eye control nit wired on the same link GRAFIK Eye shade btton colmns will control assigned motor grop controller otpts in the following fashion: Top btton: Press to move to pper/open set limit Middle btton(s): Stop moving Bottom btton: Press to move to lower/ closed set limit Raise: Press and hold to raise/open while btton is pressed Lower: Press and hold to lower/close while btton is pressed Ordering the model nmber with the -NST sffix will provide the engraved keypad shown above. Operation with seetoch wallstation Each motor grop controller otpt can be assigned independently to any Shade type seetoch wallstation wired on the same link seetoch wallstations will control assigned motor grop controller otpts in the following fashion: Preset Preset Grop 1 Grop 2 Grop 3 Preset c Operation with Pico wireless control (throgh a Sensor Modle) Up to ten (10) Pico wireless controls can be associated with a Sensor Modle (M) Up to 100 Pico Wireless controls can be associated to Ms on a link Each motor grop controller otpt can be assigned independently to any Shade Pico wireless control that is associated to a M on the same link Pico wireless controls will control assigned motor grop controller otpts in the following fashion: Top btton: Press and release to send shades to pper/open set limit Raise: Press and hold to raise/open shades Lower: Press and hold to lower/close shades Bottom btton: Press and release to lower shades to lower/closed set limit LUTRON Note: Models with a center ("favorite") btton will stop the shades when they are moving when favorite btton is pressed. Operation with E-CI-NWK-E Control Interface Each otpt on the motor grop controller can be individally controlled to Raise, Lower, or Stop. See the E-CI-NWK-E integration docment at for details. Top btton: Press to move to pper/open set limit Middle btton(s): Stop moving Bottom btton: Press to move to lower/closed set limit Raise: Press and hold to raise/open while btton is pressed Lower: Press and hold to lower/close while btton is pressed OR /Stop//Stop (single btton)

5 Motor Grop Controller E-CI-4M-D 4-Otpt AC Motor Controller Mains Voltage and Load Wiring c ,2 N m L N L N G Zone select bttons Raise/Lower bttons Option btton From Distribtion Panel Hot/Live Netral Feed N Motor Load Raise/ Lower/ E-CI-4M-D 1,2 N m L N Btton Fnctions Zone Select bttons: Zn. 1 Select desired zone LED LED indicates which zone is selected Raise/Lower bttons: Raise/Lower selected zone LEDs indicate which direction (Raise/Stop/Lower) is active LEDs Option btton: Advanced programming ( stand-alone systems only) LEDs indicate which fnction is active Def = Defalt Opt1 = Option 1 Opt2 = Option 2 LEDs Wiring from Distribtion Panel to Motor Grop Controller Trn off all circit breakers or isolators feeding the motor grop controller nit at distribtion panel. Rn hot/live, netral, and grond/earth ( ) wires from a 230 V~ 50/60 Hz feed to the motor grop controller. Follow appropriate local and national codes to avoid violating reqired separation gidelines between Mains wiring and IEC PELV/NEC Class 2 wiring. Note Before proceeding with the line voltage/mains wiring, set the pper/open and lower/close limits for each motor. Refer to the manfactrer's instrctions for instrctions for yor specific motor.

6 1,2 N m M Motor Grop Controller E-CI-4M-D 4-Otpt AC Motor Controller Wiring: Link c E-CI-4M-D L N 230 V~ 1,5 A (x8) IEC PELV/NEC Class 2 Link Wiring Link commnicates sing IEC PELV/NEC Class 2 wiring. Follow all applicable national and local codes for proper circit separation and protection. Wiring may be daisy chained or t-tapped. Total length of link mst not exceed 610 m (2 000 ft). For lengths nder 150 m (500 ft), se 1,0 mm 2 (18 AWG) condctor for control power (). For lengths over 150 m (500 ft), se 4,0 mm 2 (12 AWG) condctor for control power (). Use one, twisted-shielded pair of 0,5 mm 2 (22 AWG) for data link (, ). (1) (2) (no connect) (3) (4) To additional devices Wire Sizes (check compatibility in yor area) Link Wiring Length Wire Gage Ltron Cable Part Nmber Less than 150 m (500 ft) Common (terminal 1) 1 1,0 mm 2 (18 AWG) GRX-CBL-346S (non-plenm) Data (terminals 3 and 4) 1 twisted, shielded pair 0,5 mm 2 (22 AWG) GRX-PCBL-346S (plenm) 150 to 610 m (500 to 2000 ft) Common (terminal 1) 1 4,0 mm 2 (12 AWG) GRX-CBL-46L (non-plenm) GRX-PCBL-46L (plenm) Data (terminals 3 and 4) 1 twisted, shielded pair 0,5 mm 2 (22 AWG)