SERIES M CONTENTS

Transcription

1 C-3.01INP0316

2

3 SERIES CONTENTS General Descrpton Unt Desgnaton Explanaton And Use Of Ratngs And Servce s Classfcaton By Applcatons Selecton Procedure For otorsed Unts Unt Versons Shaft Optons otor Adaptors Lubrcaton ountng Postons OTORISED otor Performance otor Detals Addtonal otor Features Addtonal Gearbox Features Exact Ratos Selecton Tables- Geared otors Dmenson Table- Geared otors otorsed Backstop odule REDUCER & Axal s On Shafts Ratngs- Input/ Dmenson Sheets- Reducer C-Flange (B14) ountng Dmesons Thermal Power Ratngs Fan Cooled Unts Reducer Backstop odule Shppng Specfcatons Safety Informaton

4 SERIES GENERAL DESCRIPTION Seres nlne geared motors and reducers provde a very effcent and compact drve soluton to meet most requrements up to 160kW wth maxmum output torque capacty of 20000Nm. The range takes advantage of many years of accumulated desgn expertse, together wth the use of hgh qualty materals and components. The end result s a seres of speed reducng and geared motors offerng hgh load carryng capacty, hgh effcency, quet runnng and relablty. The Range Includes 13 szes of unt wth a rato coverage of 3.6/1 to 56/1 n double reducton and up to 225/1 n trple reducton and 10000/1 n combned unts. Unt Versons Avalable Two stage base mounted motorsed B C - 1 A. 7 5 A - - Base or Flange ounted Unt type - otorsed wth IEC standard motor Unt type G - Unt to allow fttng of a standard IEC motor Unt type R - Reducer unt Unt type S - Reducer unt wth fan kt Unt type W - Reducer unt wth backstop CCW rotaton Unt type X - Reducer unt wth backstop CW rotaton Unt type Y - Reducer unt wth fan and backstop CW rotaton Unt type Z - Reducer unt wth fan and backstop CCW rotaton Desgn Features Include Patented standard motor connecton (IEC). Ablty to ft double ol seal nput and output as requred. All unts beng sutable to ft IEC standard motors. All unts are dmensonally nterchangeable wth other major manufacturers. Brake geared motors are avalable. s 01, 02, 03, 04, 05, 06 and 07 are all suppled wth lubrcant. s 08, 09, 10, 13, 14 and 16 are suppled wthout lubrcant. otorsed unts can be ftted wth a backstop module and reducer unts can be ftted wth a backstop and fan. As mprovements n desgn are beng made contnually ths specfcaton s not to be regarded as bndng n detal and drawngs and capactes are subject to alteraton wthout notce. Certfed drawngs wll be sent on request. Four stage base mounted motorsed B C - 1 A. 1 8 A - - Three stage flange mounted motorsed L C - 1 A. 7 5 A - - Two stage base mounted reducer B R C * Typcal unt desgnatons 1

5 SERIES UNIT DESIGNATION 1 - Seres Range Example * Seres of Unt No of Reductons Revson Verson Nomnal Overall Rato Unt Verson Type of Unt Shaft otor Adaptor ountng Poston Geared otor Power No of otor Poles Addtonal otor Features Addtonal Gearbox Features B C - 1 A. 7 5 A Addtonal Gearbox Features Double Ol Seal, otorsed Backstop Etc 2, 3 - of Unt 0 1 Through No of Reductons 2 Through Revson Verson 2 6, 7, 8 - Nomnal Overall Rato eg Unt Verson B? E - Base ounted - B5 (D) Flange ounted (entry dependant on flange sze) - B14 (C) Flange ountng - eg - F 19 - Addtonal otor Features eg - A For Types Wthout otor Enter No of otor Poles - No motor 50 Hz 60 Hz 4 Pole (Std) 1500 rpm A 1800 rpm B 4 Pole (Hgh) 1500 rpm K 1800 rpm L 6 Pole (Std) 1000 rpm C 1200 rpm D 6 Pole (Hgh) 1000 rpm 1200 rpm N 2 Pole 3000 rpm E 3600 rpm F 8 Pole 750 rpm G 900 rpm H S Dual speed or specal motor 15, 16, 17 - Geared otor Powers 10 - Type of Unt - otorsed wth IEC standard motor G - Unt to allow fttng of IEC motor (customer own motor) R - Reducer unt S - Reducer unt wth fan kt W - Reducer unt wth backstop CCW rotaton X - Reducer unt wth backstop CW rotaton Y - Reducer unt wth fan and backstop CW rotaton Z - Reducer unt wth fan and backstop CCW rotaton , 14 - C eg. 7 5 For reducer and non standard ountng Poston eg otor Power Requred motor types enter 2 B otor Adaptor For Unt Types Column 10 Entres, N, H, E, G or A For All Other Types Enter Shaft - Standard Z - Specal * Ths Page ay Be Photocoped Allowng The Customer To Enter Ther Order. 2

6 SERIES EXPLANATION & USE OF RATINGS & SERVICE FACTORS A gear unt selecton s made by comparng actual loads wth catalogue ratngs. Catalogue ratngs are based on a standard set of loadng condtons, whereas actual load condtons vary accordng to type of applcaton. Servce s are therefore used to calculate an equvalent load to compare wth catalogue ratngs..e. Equvalent = Actual x Servce echancal Ratngs and Servce s Fm and Fs echancal ratngs measure capacty n terms of lfe and/or strength, assumng 10 hr/day contnuous runnng under unform load condtons. Catalogue ratngs allow 100% overload at startng, brakng or momentarly durng operaton up to 10 hours per day. The unt selected must therefore have a catalogue ratng at least equal to half maxmum overload. echancal Servce Fm (Table 1) s used to modfy the actual load accordng to daly operatng tme, and type of loadng. characterstcs for a wde range of applcatons are detaled n Table 3 opposte, whch are used n decdng the approprate Servce Fm from Table 1. If overloads can be calculated, or accurately assessed, actual loads should be used nstead of Fm. For unts subjected to frequent stop/starts overloads n excess of 10 tmes/day multply factor Fm x Fs (table 2). For applcatons where unts are to operate n extremely dusty or most/humd atmospheres unt selecton should be referred to applcaton engneerng. Table 1. echancal Servce (Fm) Prme over Electrc otor, Steam Turbne or Hydraulc otor Duraton of Servce Hours per day < > 10 Unform mass acceleraton factor < Classfcaton-Drven achne oderate mass acceleraton factor < Heavy mass acceleraton factor < ult-cylnder Internal Combuston Engne < > Sngle-cylnder Internal Combuston Engne < > ass acceleraton factor = all external moments of nerta * moment of nerta of drvng motor * calculated wth reference to the motor speed Table 2. Number of Starts (Fs) Start / Stops per hour (1) > 200 Fs Note: Intermedate values are obtaned by lnear nterpolaton 3

7 SERIES LOAD CLASSIFICATION BY APPLICATION Unform =oderate Shock H =Heavy Shock =Consult our Engneers Agtators Pure lquds Lquds and solds Lquds varable densty Blowers Centrfugal Lobe Vane Brewng & dstllng Bottlng machnery Brew Kettles Cookers ash tubs Scale hopper Crane knfe Car dumper Car puller Clay wokrng machnery Brck press Brquette machne Clay workng machnery Plug mll Compressors Centrfugal Lobe Recprocatng ult cylnder Sngle cylnder Conveyors- Lght duty unform load Apron Assembly Belt Bucket Chan Flght Oven Screw Conveyors - Heavy duty unform load Apron Assembly Belt Bucket Chan Flght Lve roll Oven Recprocatng Screw Shaker Cranes Crusher Ore Stone Sugar Dredger Cable reals Conveyors Cutter head drve Pumps Screen drve Stackers Wnches U U U U H H U H U U U U U U U U H H H H H Elevators Bucket - Unform load Bucket - Heavy load Bucket - Contnuous Centrfugal dscharge Escalators Freght Gravty dscharge Passenger lfts Fans Centrfugal Coolng towers Induced draft Forced draft Fan - Large dameter nduced draft Fan - Lght, small dameter Feeders Apron Belt Dsc Recprocatng Screw Food ndustry Cereal cooker Dough mxer eat grnder eat slcer Generators - not weldng Hammer mlls Hosts Heavy duty edum duty Skp host Laundry Tumbler Washer Lne shafts Heavy duty Lght duty Lumber ndustry Barkers Burner conveyor Chan/ Drag saw Chan transfer Chan way transfer De- barkng drum Edger feed Gang feed Green chan Lve roll Log deck Log haul Log turnng Log converyor Of bearng roll Planer feed chanes Planer host Re-saw conveyor Roll cases Slab conveyor Sortng table - trple host Trple host - Drve /conveyor Transfer converor Transfer roll Tray drve Trmmer feed Waster conveyor Small waste conveyor (belt) Small waste conveyor (chan) U U U U U U H U U H H U H H H H H H H H H H H H U U U achne Tools Bendng roll Punch press Notchng press Plate planer Other machne tools an drve Aux drve etal mlls Carrage/man drve Draw bench Dryer Flattenng machnery Pnch drve Reversng sltters Scrubber rolls Table conveyors Group drves Indvdual drves Table conveyors- reversng Wre draw Wre roll lls Cement kln Dryer, Cooler Kln (other) Rod plan Rod wedge bar Rotary/ Ball Tumblng barrel xers Concrete Cons densty Varable densty Ol ndustry Chller s Ol well pump Flter press Rotary kln Paper ndustry Agtator (mxer) Barker (hydraulc) Barker (mechancal) Barkng drum Beater & Pulper Bleacher Calednders Calenders- super Convertng machne Conveyors Couch Cutters - plates Cylnders Dryers Felt stretcher Felt whpper Jordans Log haul achne real Presses Stock chest Sucton roll Washers & thckeners Wnders Prntng presses Pullers Barge haul H H H U H H H H H H H H H H U H H U H U H H H H Pumps Centrfugal proportonng Proportonng Recprocatng Sngle actng 3+ cylnders Double actng 2+ cylnders Sngle actng 1 & 2 cylnders Double actng 1 cylnder Rotary- gear type Rotary- lobe type/ vane Sand muller Sewage treatment Bar screen Chemcal feeder Collector Dewaterng screw xers Scum breaker Thckness Screens Ar washng Rotary, stone or gravel Travelng water ntake Slab pushers Slewng Steerng gear Stokers Sugar ndustry Can knfe Crusher lls Textle ndustry Batchers Calenders Cards Dry cans Dryers Dyeng machnery Knttng machnery Looms angles Nappers Pads Range drve Slashers Soapers Spnners Tenter frame Washers Wnders Wndlass U U U U U U U U H U 4

8 SERIES SELECTION PROCEDURE FOR OTORISED UNITS EXAPLE APPLICATION DETAILS Absorbed power of drven machne = 0.7 kw speed of gearbox or Input speed of machne = 63 rev/mn Applcaton = Unformly loaded belt conveyor Duraton of servce (hours per day) = 24hrs ountng poston = 1 Ambent temperature = 20 o C Runnng tme (%) = 100% 2 DETERINE REQUIRED OUTPUT TORQUE AT GEARBOX OUTPUTSHAFT Absorbed = Absorbed power x 9550 output torque Gearbox output speed 0.7 x 9550 = 106 Nm 63 1 DETERINE ECHANICAL SERVICE FACTOR (Fm) Refer to Classfcaton by Applcaton, table 3, page 4 Applcaton = Unformly loaded belt conveyor Conveyors-unformly loaded or fed apron U U = Unform load assembly U belt U bucket U chan U Refer to mechancal servce factor (Fm), table 1, page 3 Duraton of servce (hours per day) = 24hrs Prme mover Electrc motor, steam turbne or hydraulc motor Duraton of servcehrs per day classfcaton-drve Unform oderate < > Therefore mechancal servce factor (Fm) = 1.25 If the unt s subject to frequent start/stops Fm must be multpled by factor Fs (see table 2 page 3) 3 SELECT GEARED OTOR Refer to selecton table one motor sze larger than absorbed power. Absorbed power = 0.7 kw, therefore refer to 0.75 kw selecton table. Always select from 4 POLE selecton table n the frst nstance as ths offers a more economcal soluton. Requred output speed of gearbox = 63 rev/mn - Choose the nearest speed = 65 rev/ mn 0.75 kw 4 POLE RP Rato 2 Nm Fm N UNIT DESIGNATION kg Servce Column Entry 1 Through 20 Spaces to be flled when enterng order Weght of Base ount Unt A A A A A A A A A A otor Frame 4 CHECK OUTPUT TORQUE torque (2) of selected unt must be equal or more than requred output torque at gearbox outputshaft. Requred output torque at gearbox outputshaft = 106 Nm 0.75 kw RP 2 Nm Fm N UNIT DESIGNATION kg 4 POLE Rato Servce Column Entry 1 Through 20 Spaces to be flled when enterng order Weght of Base ount Unt otor Frame A A A A A A A A A A Go to pont 5 5

9 SERIES SELECTION PROCEDURE FOR OTORISED UNITS 5 CHECK SERVICE FACTOR Servce factor (Fm) of selected unt must be equal or more than requred servce factor. Requred servce factor of gearbox = kw RP 4 POLE Rato 2 Nm Fm Servce N Column Entry 1 Through 20 Spaces to be flled when enterng order A A A A A A A A A A Selected unt s servce factor (Fm) = 1.48 therefore unt s acceptable. Alternatvely a 03 unt could be selected whch has a greater servce factor UNIT DESIGNATION kg Weght of Base ount Unt otor Frame 0.75 kw RP 4 POLE Rato 2 Nm Fm Servce N UNIT DESIGNATION Column Entry 1 Through 20 Spaces to be flled when enterng order A A A A A A A A A kg Weght of Base ount Unt otor Frame Selected unt s servce factor (Fm) = 1.94 therefore unt s acceptable. 6 CHECK OVERHUNG LOADS If sprocket, gear, etc s mounted on the outputshaft then refer to s Procedure, page 93, and compare wth allowable overhung load (N) of selected unt Allowable overhung load (N) must be equal or more than calculated overhung load (P) 0.75 kw RP 4 POLE Rato 2 Nm Fm Servce N UNIT DESIGNATION Column Entry 1 Through - 20 Spaces to be flled when enterng order A A A A A A A A A kg Weght of Base ount Unt otor Frame NOTE: If any of the followng condtons occur then consult Applcaton Engneerng:- a) ass acceleraton factor > 10 b) Ambent temperature s above 40 o C 6

10 SERIES UNIT VERSIONS Unt Versons Column 9 Entry B E - Base ounted - Flange mount wth B14 (C) Flange ountng Flange ounted Letter Entry Depends on Flange Dameter See tables below Flange Dameter Column 9 Entry Flange Dameter Column 9 Entry 120 H 140 J 160 K 200 L 250 N 300 P 350 R 450 S 550 T 660 U Double Trple Quadruple Quntuple Flange Da Column 9 Entry 120 H 140 J 160 K 200 L 120 H 140 J 160 K 200 L 120 H 140 J 160 K 200 L 140 J 160 K 200 L 250 N 140 J 160 K 200 L 250 N 200 L 250 N 300 P 200 L 250 N 300 P 300 P 350 R 350 R 450 S 350 R 450 S 450 S 550 T 450 S 550 T 550 T 660 U 7

11 SERIES OUTPUT SHAFT OPTIONS shaft Optons L11 L12 t Column 11 Entry * Inch shaft has an open ended keyway, therefore no L11 dmenson s requred. w L u Od C Standard shaft optons - double, trple, quadruple and quntuple reducton shaft Column 11 entry Dmensons n mm ød L L11 L12 t u w 01 Standard C / x Standard C / x Standard C / x Standard C / x Standard C / x Standard C / x Standard C / x Standard C / x Standard C / x Standard C / x Standard C / x Standard C / x 3.0, Standard C / x 50 8

12 SERIES OTOR ADAPTERS Integral otor 4 Pole - Column 19 Entry - I Power Kw Kw Kw Kw Kw Kw Kw Kw Kw Kw Kw Standard otor IEC B14- Column 12 entry otor Double Reducton Unts H H - H - H B K B K B K - G - G - G - G 90 D R D R D R - J - J - J - J 100 E S E S E S B L B L B L B L 112 E S E S E S B L B L B L B L Standard otor IEC B5- Column 12 entry otor F F - F - F - V - V - V G G - G - G - D - D - D A J A J A J W F W F W F - F - D - E C Q C Q C Q Y H Y H Y H - H - E - F A K A K A K A K A F - G - E - G N - S W A K A K A K A K A F - G - E - G N - S W N P N P N P C B G - H - F - H P - T X E P C H A J A G A J Q A G N B K B H B K R B H P - - A C L C J C L S C J Q - - B D D K D T D K R - - C E U - E L - - D E F W - F - - F G H J K 9

13 SERIES OTOR ADAPTERS Integral otor 4 Pole - Column 19 Entry - I Power Trple Reducton Unts 0.25 Kw Kw Kw Kw Kw Kw Kw Kw Kw Kw Kw Standard otor IEC B14- Column 12 entry otor H H H H H H K K K K K K G G 90 R R R R R R J J 100 S S S S S S L L 112 S S S S S S L L Standard otor IEC B5- Column 12 entry otor F F F F F F V G G G G G G D J J J J J J F F D E Q Q Q Q Q Q H H E F K K F G E E S W K K F G E E S W P G H F F T X P H J G G G N K H H H P L J J J Q K K K R L

14 SERIES OTOR ADAPTERS Quadruple Reducton Unts Integral otor 4 Pole - Column 19 Entry - I Power All Ratos All Ratos All Ratos All Ratos 0.25 Kw Kw Kw Kw Kw Kw Kw Kw Kw Kw Kw All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos Standard otor IEC B14- Column 12 entry otor All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos 71 H H H H H K K K K K G G G G G 90 R R R R R J J J J J 100 S S S S S L L L L L 112 S S S S S L L L L L Standard otor IEC B5- Column 12 entry otor All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos 63 F F F F F V V G G G G G D D J J J J J F F F F F E 90 Q Q Q Q Q H H H H H F K K K K K G K K K K K G P P H P P P J 11

15 SERIES OTOR ADAPTERS Quntuple Reducton Unts Integral otor 4 Pole - Column 19 Entry - I Power All Ratos All Ratos All Ratos All Ratos All Ratos 0.25 Kw Kw Kw Kw Kw Kw Kw Kw All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos Standard otor IEC B14- Column 12 entry otor All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos 71 H H H H H H H H K K K K K K K K G G 90 R R R R R R R R J J 100 S S S S S S S S L L 112 S S S S S S S S L L Standard otor IEC B5- Column 12 entry otor All Ratos All Ratos All Ratos All Ratos All Ratos 63 F F F F F F F V V V - 71 G G G G G G G D D D - 80 J J J J J J J F F F D 90 Q Q Q Q Q Q Q H H H E K K K F K K K F P P P G H All Ratos All Ratos All Ratos All Ratos All Ratos All Ratos 12

16 SERIES LUBRICATION 01,02,03,04,05,06,& 07 Unts, are suppled factory flled wth EP mneral ol (Grade 6E) approprate to the ntended mountng poston. If the unt s suppled wthout lubrcant the unt must be flled wth the correct lubrcant and quantty as lsted below. 08,09,10,13, 14 & 16 Unts, requre fllng wth EP mneral ol (Grade 6E) Lubrcant quanttes are approxmate fll untl ol escapes from the level plug hole, ft ventlator plug (when suppled) n the approprate poston for the requred mountng poston. If the unt s suppled wthout lubrcant the unt must be flled wth the correct lubrcant and quantty. Temperature lmtatons The standard lubrcant s sutable for operaton n ambent temperatures of 0 to 35 C, outsde of ths consult table 1 or applcaton engneers. Table 1 ol grades Lubrcant 5 C - 20 C (E) -30 C - 20 C (H) Ambent temperature range 0 C - 35 C 20 C - 50 C EP neral ol (type E) Polyalphaolefn based synthetc (type H) 5E (VG 220) 6E (VG 320) 7E (VG 460) 5H (VG 220) 5H (VG 220) 6H (VG 320) Table 2 lubrcaton quantty (ltres) ountng Poston Double reducton & fnal stage quadruple or quntuple reducton ountng Poston Prmary stage quadruple reducton (Quanttes obtaned from above double and trple szes ndcated) Prmary Unt sze Secondary Unt sze Prmary stage quntuple reducton (Quanttes obtaned from above double and trple szes ndcated) Prmary Unt sze Secondary Unt sze

17 Column 13 Entry SERIES OUNTING POSITIONS Base ounted Unts Flange ounted Unts 6* V3 2 B7 1 B3 5 V5 6* 3 B6 V6 5 V1 1 B5 4 B8 * ountng Poston 6 s not recommended for Geared otors - Consult Applcaton Engneerng Gear Unts selected for use n mountng postons 5 and 6 should only be used wth overall ratos greater or equal to those shown n the table below Input (rpm) < 1000 < 1500 < 1800 > All All All Consult Applcaton Engneerng ountng Postons - shown as motorsed - apples also for reducers Column 14 Entry 270o All motors 180o 0 o Column 14 Entry Termnal Box Poston A 0 B 90 C 180 D Reducer or no motor ftted 90 o 14

18 SERIES NOTES 15

19 SERIES OTORISED SERIES 16

20 17 SERIES

21 SERIES OTOR DETAILS B14 'C' face k0 g1 m g6 Ø m Ø n Ø d Ø k0 g Ø g1 e m Øs øg6 øm øn ød e ko øg g1 m øs e deg Øs 4x deg 4x6 90S deg 4x8 90L deg 4x8 100L deg 4x deg 4x8 k0 g1 g6 g6 m n d g Ø m Ø n Ø Ø Ø d Ø Ø Ø Ø B5 'D' face k0 g Ø m g1 g6 Ø m Ø n Ø d Ø e g Ø m Ø s e Ø s øg6 øm øn ød e ko øg g1 m øs deg 4x deg 4x deg 4x10 90S deg 4x10 90L deg 4x10 100L deg 4x deg 4x12 132S deg 4x deg 4x deg 4x16 160L deg 4x deg 4x16 180L deg 4x16 200L deg 4x16 225S deg 8x deg 8x deg 8x16 280S deg 8x deg 8x16 315S deg 8x deg 8x20 315L deg 8x20 * otor lengths for own brand standard motors. These lengths may vary f alternatve motor s ftted. 18

22 SERIES ADDITIONAL OTOR FEATURES RADICON POWERBUILD motor features - Column 19 Entry Brake oter (wth RL) (Consult PBL Desgn for Detal) (Consult PBL Desgn for Detal) (Other than above) 19

23 SERIES ADDITIONAL GEARBOX FEATURES Addtonal Gearbox Features - Column 20 Entry Column 20 entry Double outputshaft ol seals* otorsed Backstop *** CW Rotaton CCW Rotaton Specal - A D E H I L Please refer to Applcaton Engneerng for detals of the followng addtonal gearbox features - Prme pant only - Wash down - Specal ol (food compatble, bo-degradable, dfferent vscostes etc) * Double Ol Seals for output shafts szes 08 to 16 only *** IEC frame szes

24 SERIES EXACT RATIOS Column Entry Exact Ratos - Double Reducton Exact Ratos - Trple Reducton Column Entry

25 SERIES EXACT RATIOS Exact Ratos - Quadruple Reducton Column Entry C C C C C C C C Exact Ratos - Quntuple Reducton Column Entry C C C C C C C C C C K

26 SERIES SELECTION TABLES 0.12 kw 4 POLE RP Rato 2 Nm Fm Unt Desgnaton N kg Servce Column Entry 1-20 Blanks to be flled when enterng order Weght of base mount unt A A A A A A A A A A A A A A A A A A A otor A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A NOTE A A Other output speeds are avalable usng 2 and 8 pole motors - Consult Applcaton Engneerng 23

27 SERIES SELECTION TABLES 0.12 kw 6 POLE RP Rato 2 Nm Fm Unt Desgnaton N kg Servce Column Entry 1-20 Blanks to be flled when enterng order Weght of base mount unt C C C C C C C C C C C C C C C C C C C otor C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C NOTE Other output speeds are avalable usng 2 and 8 pole motors - Consult Applcaton Engneerng C C C C C

28 SERIES SELECTION TABLES 0.18 kw 4 POLE RP Rato 2 Nm Fm Unt Desgnaton N kg Servce Column Entry 1-20 Blanks to be flled when enterng order Weght of base mount unt A A A A A A A A A A A A A A A A A A A otor A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A NOTE Other output speeds are avalable usng 2 and 8 pole motors - Consult Applcaton Engneerng A A A A A A A A A A A

29 SERIES SELECTION TABLES 0.18 kw 4 POLE RP 2 Nm Fm Unt Desgnaton N kg Servce Column Entry Weght of 1-20 otor Rato base Blanks to be flled when enterng order mount unt A A A A A A A A A A A A A A A A A A A A kw 6 POLE A A A A A A A A A A A C C C C C C C C C C C C C C C C C C C C C C C C C C C C NOTE Other output speeds are avalable usng 2 and 8 pole motors - Consult Applcaton Engneerng C C C C C C C C C C C C

30 SERIES SELECTION TABLES 0.18 kw 6 POLE RP Rato 2 Nm Fm Unt Desgnaton N kg Servce Column Entry 1-20 Blanks to be flled when enterng order Weght of base mount unt C C C C C C C C C C otor C C C C C C C C C C C C C C C C C C C C C C C C C NOTE 0.25 kw Other output speeds are avalable usng 2 and 8 pole motors - Consult Applcaton Engneerng 4 POLE C C C C C C C C C A A A A A A A A A A A A A A A A A A A A A A A A A A

31 SERIES SELECTION TABLES 0.25 kw 4 POLE RP Rato 2 Nm Fm Unt Desgnaton N kg Servce Column Entry 1-20 Blanks to be flled when enterng order Weght of base mount unt A A A A A A otor A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A NOTE Other output speeds are avalable usng 2 and 8 pole motors - Consult Applcaton Engneerng A A A A A A A A A