SRB Series. UL Recognized CSA Certified VDE Approved* Specifications. SRB Series. Power Inlet Filters & Power Entry Modules

Transcription

1 orcom Product Guide atalog: 161 Issue ate: 6.11 Minimum epth, ost-effective Shielded Power Inlet Filter SR Series UL Recognized S ertified V pproved* SRP SRS8 SR1 SR2 SR Series Smallest depth orcom RFI filter available omplete shield Wide range of capacitor values ttenuates coupled MI up to MHz Minimal to low leakage current versions are suitable for patient and non-patient contact medical equipment. Full range of mounting and termination options including unique vertical and horizontal orientation slide in mounts eliminate the need for mounting hardware Ordering Information SR S 1 - Q apacitor I See hart Omit if none Output Styles 1 Spade terminals (back) 2 Spade terminals (bottom) 8 Wire leads P P board pins Mounting Style S Snap-in X Slide-in (short edge / horizontal) Y Slide-in (long edge / vertical) Omit for flange mount SR Series urrent Rating * versions are tested by Underwriters Laboratories to US and anadian requirements and are V approved at, V Specifications imensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. imensions are shown for reference purposes only. Maximum leakage current each Line to V apacitor I / Value 6 Hz Hz lank / None 2 Q / pf R / pf S / 2 pf T / pf W / 47 pf.4 m.7 m X / pf.7 m.1 m Y / 2 pf.16 m.28 m Z / pf.24 m.42 m Hipot rating (one minute): Line to Ground: V Line to Line: 14 V Rated Voltage (max.): V Operating Frequency: /6 Hz Rated urrent: * Operating mbient Temperature Range (at rated current I r ): - to + In an ambient temperature (T a ) higher than + the maximum operating current (I o ) is calculated as follows: I o = I r (8-Ta)/4 apacitor Options apacitor I apacitor Value Q pf R pf S 2 pf T pf W 47 pf X pf Y* 2 pf Z* pf *Not available in SR8, SRX or SRY styles Power Inlet Filters & Power ntry Modules

2 orcom Product Guide atalog: 161 Issue ate: 6.11 Minimum epth, ost-effective Shielded Power Inlet Filter (continued) SR Series vailable Part Numbers Flange Mount SR1 SR2 SRP SR8 SR1-Q SR2-Q SRP-Q SR8-Q SR1-R SR2-R SRP-R SR8-R SR1-S SR2-S SRP-S SR8-S SR1-T SR2-T SRP-T SR8-T SR1-W SR2-W SRP-W SR8-W SR1-X SR2-X SRP-X SR8-X SR1-Y SR2-Y SRP-Y SR1-Z SR2-Z SRP-Z Snap-In Slide-In SRS1 SRS8 SRX8 SRY8 SRS1-Q SRS8-Q SRX8-Q SRY8-Q SRS1-R SRS8-R SRX8-R SRY8-R SRS1-S SRS8-S SRX8-S SRY8-S SRS1-T SRS8-T SRX8-T SRY8-T SRS1-W SRS8-W SRX8-W SRY8-W SRS1-X SRS8-X SRX8-X SRY8-X SRS1-Y SRS1-Z lectrical Schematic LIN LO ase Styles SR1 SRP SR2 ccessories G: NM -P to I line cord SRS1 4 imensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. imensions are shown for reference purposes only.

3 orcom Product Guide atalog: 161 Issue ate: 6.11 Minimum epth, ost-effective Shielded Power Inlet Filter (continued) SR Series ase Styles (continued) SR8 SRY8.4 lue lue Green/Yellow rown Grn/Yel rown ngage panel edge here.96 max SRS8 SRX8.96 max lue Green/Yellow rown lue Grn/Yel rown ase imensions Part No. SR1 SR2 SRP SRS1 SR8 SRS8 SRX8 SRY8 Power Inlet Filters & Power ntry Modules ngage panel edge here imensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. imensions are shown for reference purposes only.

4 orcom Product Guide atalog: 161 Issue ate: 6.11 Minimum epth, ost-effective Shielded Power Inlet Filter (continued) SR Series Recommended Panel utouts P oard Layout SR1, SR2, SRP & SR Front Mount ack Mount R.. Typ Tolerances ±. [.1] unless otherwise noted R..94 Typ..68* 17.* *±. [.8] SRS G.188 R Max SRX Tolerance ±.2 [.] SRX8 over Jacket Flange min. min.. R max Panel ±. [.127] Thickness.9 [1.] ±. [.127] SRY over Jacket Flange. R max ±. [.127] min. min. Panel Thickness.9 [1.] ±. [.127] 6 imensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. imensions are shown for reference purposes only.

5 orcom Product Guide atalog: 161 Issue ate: 6.11 Minimum epth, ost-effective Shielded Power Inlet Filter (continued) SR Series Performance ata Typical Insertion Loss Measured in closed Ohm system Q R S T W X Y Z 1 Minimum Insertion Loss Measured in closed Ohm system 1 1 ommon Mode / symmetrical (L-G) ifferential Mode / Symmetrical (L-L) ommon Mode / symmetrical (Line to Ground) 1 Power Inlet Filters & Power ntry Modules imensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. imensions are shown for reference purposes only. 7