Type 4 Panel Enclosures

Transcription

1 Ground-Mount Enclosures Type 4 Free-Standing ata Sheet Finish Wash and phosphate undercoat NSI 61 gray polyester powder finish pplication Houses electrical controls and instruments Easy access panels or rack mounts for housing optional equipment Intended for indoor or outdoor use Protects against windblown dust and rain, splashing water and hose directed water Standards UL 508 Listed, Type 4 and Type 12 S 22.2 No. 94 ertified, Type 4 and Type 12 onforms to NEM Standard for Type 4 and Type 12 E.I.. RS-310- ccessories Full and half panels Side and swing panels hannel mounting Equipment rack mounts Touch-up paint See ccessories section onstruction Enclosure and door are fabricated from (12) gauge steel ll continuous welded seams are finished smooth oors are secured to the body with a heavy duty continuous hinge on one side and easy-to-release stainless steel door clamps mounted to the other three sides oor has a seamless poured in place gasket Ground stud provided on door Each door has a padlock hasp with sealing hole provision Print pocket provided Large lifting eyebolts are supplied Mounting channels are welded inside for locating panels or rack mount equipment along enclosure depth variety of optional panels and accessories are available 32 ETON ORPORTION May 2013

2 Ground-Mount Enclosures Type 4 Free-Standing Illustration Sheet and atalog Number Enclosure Enclosure Size x epth xx atalog # in. mm. in. mm. H FS x x x 635 x H FS x x x 787 x H FS x x x 940 x H FS x x x 635 x H FS x x x 787 x H FS x x x 940 x lifting eye (67) (95) padlock hasp L (273) door clamp (see note on this page) 3.50 (89) 8.87 (225) print pocket (supplied) L Front View 7.37 (187) mounting channel Side View Notes: Four lifting eyes are furnished when dimension is 24 (610 mm). lamps are mounted along three sides of the enclosure door. Spacing between clamps along side opposite the hinge does not exceed 15 inches. imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. ETON ORPORTION May

3 Ground-Mount Enclosures Type 4 Free-Standing with Quarter-Turn Latches ata Sheet and atalog Number Finish Wash and phosphate undercoat NSI 61 gray polyester powder finish ccessories Full and half panels Side and swing panels support kit lifting kit hannel mounting Equipment rack mounts Lights Window kits pplication Houses electrical controls and instruments Easy access panels or rack mounts for housing optional equipment Intended for indoor or outdoor use Protects against windblown dust and rain, splashing water and hose directed water onstruction Enclosure and doors are fabricated from (12) gauge steel ll continuous welded seams are finished smooth Heavy duty continuous hinge with stainless steel hinge pin Slotted quarter-turn flush latch(es) oor has a seamless poured in place gasket Formed lip around enclosure opening diverts liquids and contaminants Ground stud provided on door Print pocket provided Mounting channels are welded inside for locating panels or rack mount equipment along enclosure depth Provision for mounting fluorescent light Large lifting eyebolts Standards UL 508 Listed, Type 4 and Type 12 S 22.2 No. 94 ertified, Type 4 and Type 12 onforms to NEM Standard for Type 3, Type 4, Type 12 E.I.. RS-310- Enclosure Enclosure Size x epth xx atalog # in. mm. in. mm. H FSQT x x x 609 x H FSQT x x x 762 x H FSQT x x x 914 x ETON ORPORTION May 2013

4 Ground-Mount Enclosures Type 4 Free-Standing with Quarter-Turn Latches Illustration Sheet lifting eye (67) (95) quarter-turn latches (273) L 3.50 (89) 8.87 (225) print pocket (supplied) L Front View 7.37 (187) mounting channel Side View Notes: Four lifting eyes are furnished when dimension is 24 (610 mm). imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. ETON ORPORTION May

5 Ground-Mount Enclosures Type 4 Free-Standing with 3-Point Locking ata Sheet Finish Wash and phosphate undercoat NSI 61 gray polyester powder finish pplication Houses electrical controls and instruments Easy access panels or rack mounts for housing optional equipment Intended for indoor or outdoor use Protects against windblown dust and rain, splashing water and hose directed water Standards UL 508 Listed, Type 4 and Type 12 S 22.2 No. 94 ertified, Type 4 and Type 12 onforms to NEM Standard for Type 3, Type 4, Type 12 E.I.. RS-310- ccessories Full and half panels Side and swing panels support kit lifting kit hannel mounting Equipment rack mounts Lights Window kits Replacement handle onstruction Enclosure and doors are fabricated from (12) gauge steel ll continuous welded seams are finished smooth Heavy duty continuous hinge with stainless steel hinge pin Internal 3-point latching with key locking and padlock handles oor has a seamless poured in place gasket Formed lip around enclosure opening diverts liquids and contaminants Ground stud provided on door Print pocket provided Mounting channels are welded inside for locating panels or rack mount equipment along enclosure depth Provision for mounting fluorescent light Large lifting eyebolts 36 ETON ORPORTION May 2013

6 Ground-Mount Enclosures Type 4 Free-Standing with 3-Point Locking Illustration Sheet and atalog Number Enclosure Enclosure Size x epth xx atalog # in. mm. in. mm. H FS3PT x x x 609 x H FS3PT x x x 609 x H FS3PT x x x 762 x H FS3PT x x x 914 x H FS3PT x x x 914 x H FS3PT x x x 609 x H FS3PT x x x 762 x H FS3PT x x x 914 x H FS3PT x x x 914 x H FS3PT x x x 914 x lifting eye (67) (95) L 3-point handle lock rotation (273) 3.50 (89) 8.87 (225) print pocket (supplied) L Front View 7.37 (187) mounting channel Side View Notes: Four lifting eyes are furnished when dimension is 24 (610 mm). imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. ETON ORPORTION May

7 Free-Standing Enclosure ccessories Type 4 Single-oor, Full and Half Illustration Sheet and atalog Number Full (Single-oor) Half (Single-oor) Size x Size x atalog # in. mm. in. mm. in. mm. HF6024P x x x x 610 HF6036P x x x x 914 HF7224P x x x x 610 HF7230P x x x x 762 HF7236P x x x x 914 atalog # in. mm. in. mm. in. mm. HF6024HP x x x x 610 HF6036HP x x x x 914 HF7224HP x x x x 610 HF7230HP x x x x 762 HF7236HP x x x x (41) (41) (41) panel side bracket included (see illustration #1 page 46 and detail sheet page 47) Half (upper mount) Full Half (lower mount) Full Mounting Half Mounting Note: Full and half panel for single-door, single and dual-access enclosures are (12) gauge steel and furnished with panel side brackets and all necessary for channel and panel mounting. Half panels can be mounted in either the upper or lower portion of the enclosure. Free-standing design permits the panel to adjust along the depth of the enclosure. With dual-access enclosures, full and half panels can be mounted back-to-back. 40 ETON ORPORTION May 2013

8 Free-Standing Enclosure ccessories Type 4 Single-oor, Full Illustration Sheet and atalog Number Size x atalog # in. mm. in. mm. in. mm. in. mm. HF6048P x x x x 1219 HF6060P x x x x 1524 HF7248P x x x x 1219 HF7260P x x x x 1524 HF7272P x x x x (41) (41) panel side bracket included (see illustration 1 page 46 and detail sheet page 47) Full center post included with double-door full panel (see illustration #5 page 46) Full Mounting Notes: Full panel for double-door, single and dual-access enclosures are (10) gauge steel and furnished with panel brackets, center post assembly, panel handle kit and all necessary for channel and panel mounting. The center post assembly offers additional support of panel and equipment. Free-standing design permits the panel to adjust along the depth of the enclosure. With dual-access enclosures, full and half panels can be mounted back-to-back. Notes: imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. ETON ORPORTION May

9 Free-Standing Enclosure ccessories Type 4 ouble-oor, Half Illustration Sheet and atalog Number Size x atalog # in. mm. in. mm. in. mm. in. mm. HF6048HP x x x x 1219 HF7248HP x x x x 1219 HF7260HP x x x x 1524 HF7272HP x x x x (41) Half (upper mount) panel side bracket included (see illustration #1 page 46 and detail sheet page 47) Half (lower mount) center post or double-door panel support bracket (sold separately) (see illustration #5 page 46) Half Mounting Note: Half panel for double-door, single and dual-access enclosures are (12) gauge steel and furnished with panel brackets and all necessary for channel and panel mounting. center post assembly or a double-door panel support bracket (catalog number HFSUP2) for additional support of the panel is optional and sold separately. Free-standing design permits the panel to adjust along the depth of the enclosure. With dual-access enclosures, full and half panels can be mounted back-to-back. 42 ETON ORPORTION May 2013

10 Free-Standing Enclosure ccessories Type 4 Side and enter Post Illustration Sheet and atalog Number Side Size x Height epth* atalog # in. mm. in. mm. in. mm in. mm. HF6018SP x x HF7218SP x x HF7224SP x x enter Post enter Post Fits Enclosure Height atalog # in. mm. in. mm. in. mm. HF60PS HF72PS * ack panels restrict the movement of side panels and will prohibit mounting in some depths. See detail sheet for back panel spacing (41) (54) Side Side Mounting Side panels are (12) gauge steel and furnished with necessary for channel mounting. They will fit any width enclosure and are adjustable along its depth, however, when full or half panels are installed, movement will be restricted and with some depths make side mounting prohibitive. enter Post ssembly enter post assembly is furnished with all double-door full panels and includes necessary for channel and panel mounting. The center post is optional on double-door half panels and swing panel mounting and must be ordered separately. It attaches to the top and bottom channels making it adjustable along the depth of the enclosure. See illustration #5 on the etail Sheet on page 46. Notes: imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. ETON ORPORTION May

11 Free-Standing Enclosure ccessories Type 4 Single-oor, Full and Half Swing Illustration Sheet and atalog Number Full Swing (Single oor) Half Swing (Single oor) Size x Size x atalog # in. mm. in. mm. in. mm. HF6024SWP x x x x 610 HF6036SWP x x x x 914 HF7224SWP x x x x 610 HF7230SWP x x x x 762 HF7236SWP x x x x 914 atalog # in. mm. in. mm. in. mm. HF6024HSWP x x x x 610 HF6036HSWP x x x x 914 HF7224HSWP x x x x 610 HF7230HSWP x x x x 762 HF7236HSWP x x x x (81) 2.06 (52) 3.18 (81) 2.06 (52) hinge hinge Full Swing swing panel bracket assembly included (see detail sheet page 48) panel side bracket included (see illustration #1 page 46 and detail sheet page 48) Half Swing (upper mount) hinge Half Swing (lower mount) Full Swing Mounting Half Swing Mounting Note: Full swing panel and half swing panel for single-door, single and dual-access enclosures are (12) gauge steel, have a dual hinge swing panel bracket and furnished with panel brackets and all necessary for channel and panel mounting. s can be installed so they hinge on either the left or right side. In addition, half panels can be mounted in either the upper or lower portion of the enclosure. Free-standing design permits the panel to be adjustable along the depth of the enclosure. The dual hinge will allow the inner panel to swing completely out of the door opening when within 5.50 inches of the front. With dual-access enclosures, full and half swing panels can be mounted back-to-back. 44 ETON ORPORTION May 2013

12 Free-Standing Enclosure ccessories Type 4 ouble-oor, Full and Half Swing Illustration Sheet and atalog Number Full Swing (Single oor) Half Swing (Single oor) Size x Size x atalog # in. mm. in. mm. in. mm. HF6024SWP x x x x 610 HF7224SWP x x x x 610 HF7230SWP x x x x 762 HF7236SWP x x x x 914 atalog # in. mm. in. mm. in. mm. HF6024HSWP x x x x 610 HF7224HSWP x x x x 610 HF7230HSWP x x x x 762 HF7236HSWP x x x x 914 center post assembly and center bracket must be ordered separately (81) 3.18 (81) panel mounting center bracket (sold separately) (see illustration #2 page 46) hinge hinge swing panel bracket assembly included (see detail sheet page 48) Full Swing Half Swing (lower mount) Swing Mounting center post and panel mounting center bracket (sold separately) (see illustration #2 and #5 page 46) Note: Full swing panel and half swing panel for double-door, single and dual-access enclosures are (12) gauge steel, have a dual hinge swing panel bracket and are furnished with necessary for side channel mounting. center post assembly and center bracket must be ordered separately. s can be installed so they hinge either on the left or right side. In addition, half panels can be mounted in either the upper or lower portion of the enclosure. Free-standing design permits the panel to adjust along the depth of the enclosure. The dual hinge will allow the inner panel to swing completely out of the door opening when within 5.50 inches of the front. With dual-access enclosures,full and half swing panels can be mounted back-to-back. Notes: imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. ETON ORPORTION May

13 Free-Standing Enclosure ccessories Type 4 Miscellaneous ccessories Illustration Sheet and atalog Number Miscellaneous ccessories atalog # escription Illustration Quantity HFSRKT1 mounting side bracket 1 1 HFRKT3 mounting center bracket 2 3 HFMH3 hannel mounting 3 3 HFPSUP2 ouble-door panel support bracket 4 2 See page 43 enter post 5 1 center bracket channel spring nut panel nut panel mounting stud side bracket channel mounting panel nut bracket mounting Illustration 1 Illustration 2 bracket mounting panel mounting stud channel spring nut Illustration 3 channel mounting panel bolt center post panel bolt panel bolt panel bolt center post panel nut install panel bolt in this hole for top of panel support channel mounting panel support bracket channel spring nut panel mounting stud panel nut channel mounting bracket mounting panel nut center post bracket mounting post bracket channel spring nut Illustration 4 Illustration 5 See catalog page 43 Notes: imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. 46 ETON ORPORTION May 2013

14 Free-Standing Enclosure etails Type 4 and Enclosure etail Sheet enclosure width (146) 2.87 min (73) 3.00 min (76) 2.87 (73) Single oor (section view showing full panels mounted back-to-back) 1/2 enclosure width (146) 2.87 min (73) 3.75 min (95) 2.87 (73) L ouble oor (section view showing full panels mounted back-to-back) (of enclosure) Notes: imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. ETON ORPORTION May

15 Free-Standing Enclosure ccessories Rack Mounting ngles Illustration Sheet and atalog Number Heavy duty rack mounting angles are designed for mounting 19 (482mm) equipment in free-standing enclosures. center post assembly, HFxxPS on page 43, and a panel mounting center bracket, HFRKT3 on page 46, (each sold separately) are required when mounting in any double door enclosure. Mounting holes are spaced at the 19 EI standard and are provided to accept #10-32, #12-24, or M6 cage nuts (sold in packages of 100), on page 50. L Shaped Mounting ngles L Equipment Mounting Holes to ccept #10-32, #12-24, or M6 age Nuts (Sold Separately) Note: L-shaped angles are universal and can be rotated to accommodate 19 or 23 EI mounting equipment (38) Mounting ngles Height L Mounting U s atalog # in. mm. in. mm. HES-48RM-L HES-60RM-L HES-72RM-L HES-90RM-L Kit contains two (2) full length L angles, installation instructions, and necessary to mount in single-door enclosures. Yellow Zinc finish. L 3.50 (89) Equipment Mounting Holes to ccept #10-32, #12-24, or M6 age Nuts (Sold Separately) 1.44 (36) O...75 (19) 2.29 (58) ngle Profile (41) O.. ngle Profile 1.50 (38) O.. Mounting ngles Hole Pattern Hole Pattern E.375 (9) Square Hole U Shaped Mounting ngles Height E.375 (9) Square Hole = 1.75 (44) =.625 (16) =.500 (13) =.295 (7) E =.250 (6) Kit contains two (2) full length U angles, installation instructions, and necessary to mount in single-door enclosures. Yellow Zinc finish. L Mounting U s atalog # in. mm. in. mm. HES-48RM-U HES-60RM-U HES-72RM-U HES-90RM-U = 1.75 (44) =.625 (16) =.500 (13) =.295 (7) E =.250 (6) Notes: imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. ETON ORPORTION May

16 Free-Standing Enclosure ccessories Frames & Fasteners Illustration Sheet and atalog Number Swing-out Rack Mounted Frame Mounting ngles Height atalog # in. mm. in. mm. HES-48SORMF HES-60SORMF HES-72SORMF HES-90SORMF L Heavy duty swing-out rack mounting frames are designed for mounting 19 (482mm) equipment in free standing enclosures. center post assembly, HFxxPS on page 43 and panel mounting center bracket, HFRKT3 on page 46, (each sold separately) are required when mounting in any double-door enclosure. Mounting holes are spaced per the EI standard and are provided to accept #10-32, #12-24 or M6 cage nuts (sold in packages of 100). Swing-out rack mounting frames have white powder coated finish. Equipment Mounting Holes to ccept #10-32, #12-24, or M6 age Nuts (Sold Separately - See elow) L Hole Pattern = 1.75 (44) =.625 (16) =.500 (13) =.295 (7) E =.250 (6) E.375 (9) Square Hole (494) O.. atalog # HE2-M-1032-PHMS-100 HE2-M-1224-PHMS-100 HE2-M-M6-PHMS-100 Screw Type #10-32 Phillips #12-24 Phillips M6 Phillips atalog # HE2-M-N HE2-M-N HE2-M-N-M6-100 Sold in bags of (100) age Nut Type #10-32 Tapped #12-24 Tapped M6 Tapped Notes: imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. 50 ETON ORPORTION May 2013

17 Free-Standing Enclosure ccessories Floor Stand & Stabilizer Kits Illustration Sheet and atalog Number atalog # Steel in. mm. in. mm. in. mm. HMFK HMFK HMFK HMFK Floor stand kits are intended for use with EnviroShield Type 4X, Type 4 and Type 12 enclosures where floor support is required. Each kit consists of two (10) gauge legs and for mounting. t the base of each leg is a pre-punched plate (see drawing). Steel kits have a gray polyester powder paint finish. Stainless steel kits are fabricated from 304 stainless steel. Standard floor stand kits are 12 inches (305 mm) high. For special heights, special material or non-standard construction, consult factory (117) 9.87 (251) 4.62 (117).50 hole (13) (305) L.50 hole (13) 7.87 (200) Floor Stand Kit 7.87 (200) ase eep 7.87 (200) ase eep Notes: imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. ETON ORPORTION May