Industrial Enclosures

Transcription

1 48J Series - NEMA 2 Large JIC Enclosures Junction Boxes Application Designed to house electrical, electronic, hydraulic or pneumatic controls and instruments. Provides a degree of protection from falling dirt, dust, oil and water. Standards UL 508 Type 2 Complies with NEMA Type 2 JIC EGP--967 unless marked IEC 529, IP65 Construction Formed from 4 gauge steel. Smooth, continuously welded seams without knockouts, cutouts or holes. Door and body stiffeners are provided in the larger enclosures for extra rigidity. Welded brackets provide for enclosure mounting. Continuously hinged cover is secured with stainless steel screws, threaded into sealed wells. Oil resistant gaskets are permanently secured and mechanically retained. A removable 2 gauge inner panel is included. Collar studs are provided for mounting inner panels. A grounding stud is provided in the enclosure and a bonding stud is provided on the door. A literature pocket is provided for the inside of the door. Finish Cover and enclosure are phosphatized and finished in ANSI/ ASA 6 gray recoatable powder coating. Removable inner panel is finished in white powder coating. Accessories Additional inner panels...see page 384 Blowers...see page 359 Breather kits...see page 374 Filter fans...see page Heaters...see page Louvered ventilating plates...see page 396 Terminal kit assemblies...see page 386 Thermostats...see page 374 Window kits...see page 39

2 48J Series - NEMA 2 Large JIC Enclosures ➊ ➏ ➋ ➎ ➍ ➌ ➊ Vertical body stiffener req d on M only ➋ Omit if center body stiffener if A is less than 4" ➌ Omit if A is less than 3" ➍ Omit 2 center studs if A is less than 3" ➎ Omit body stiffeners if B is less than 29" ➏ Omit 2 middle studs if B is less than 3" Top View ➐ Junction Boxes/JIC Enclosures Front View ➐ Omit door stiffener if A or B is 24" or less Panel Dimensions Centers Ship Part No. A B C D E F G H J Wt. lbs 48JB JC JD JE JJ JF JK JL JC JD JE JJ JK JF JM JL JO JP JJ JL JS JK JM Does not meet JIC requirements Section Z-Z When A= M=

3 48 Series 304 Stainless Steel Single Door Enclosures - NEMA 4X Continuous Hinge, Clamped Cover Inner Panel Included Wallmount Enclosures Application Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures. Provides protection where equipment may be hosed down or otherwise be very wet, or in specific applications where corrosion is a serious problem. Standards UL 508 Type 3R, 4, 4X, and 2 CSA Type 3R, 4, 4X, and 2 Complies with NEMA Type 3R, 4, 4X, 2 and 3 JIC EGP--967 unless marked IEC 529, IP66 Construction Formed 4 gauge Type 304 stainless steel bodies and doors. Smooth, continuously welded seams without knockouts, cutouts or holes. Door and body stiffeners are provided in the larger enclosures for extra rigidity. Welded brackets provide for enclosure mounting. Formed lip on door and enclosure excludes flowing liquids and contaminants. Stainless steel continuous hinge on door may be removed by pulling the stainless steel hinge pin. Door is secured with easily operated stainless steel clamps. Provision for padlocking. Oil resistant gaskets are permanently secured. A removable 2 gauge inner panel is included. Collar studs are provided for mounting inner panels. A bonding stud is provided on the door and a grounding stud is provided in the enclosure. A literature pocket is provided for the inside of the door. New Sizes Available! Finish Cover and enclosure are natural stainless steel with a smooth brushed finish. Removable inner panel is finished in white powder coating. Accessories Additional inner panels...see page 384 Air conditioners...see page Blowers...see page 359 Breather kits...see page 374 Door clamping hardware...see page 378 Door stop kits...see page 393 Drip shield kits...see page 393 Enclosure stabilizers...see page 397 Filter fans...see page Floor stand kits...see page 394 Heaters...see page Lock kit...see page 379 Louvered ventilating plates...see page 396 Quick release clamp...see page 378 Terminal kit assemblies...see page 386 Thermostats...see page 374 Window kits...see page 39

4 48 Series 304 Stainless Steel Single Door Enclosures - NEMA 4X Continuous Hinge, Clamped Cover ➊ ➋ ➍ ➌ ➐ Front View ➏ ➎ Section Z-Z When A= M= ➊ Vertical stiffener required on KK, LL & M only. ➋ Omit center body stiffener if A is less than 4". ➌ Padlocking hasp and staple. ➍ Omit 2 middle studs if A is less than 3". ➎ Omit body stiffeners if A or B is less than 29". ➏ Omit 2 middle studs if B is less than 3". ➐ Omit door stiffener if A or B is less than 3" except if AxB is 42"x30". Literature pocket supplied loose. Number of door clamps varies to enclosure size. Wallmount Enclosures Section Y-Y Panel Size Mtg.Centers Ship Part No. A B C D E F G Wt. lbs. 48N4SSB N4SSG N4SSCR N4SSC N4SSD N4SSE N4SSJ N4SSB N4SSC N4SSD N4SSER N4SSH N4SSE N4SSJ N4SSKR N4SSF N4SSK N4SSKK N4SSL Does not meet JIC requirements 2 Flat panel Panel Size Mtg.Centers Ship Part No. A B C D E F G Wt. lbs. 48N4SSM N4SSP N4SSS N4SSC N4SSE N4SSK N4SSL N4SSM N4SSO N4SSS N4SSJ N4SSK N4SSM N4SSLL N4SSS N4SST N4SSK N4SSM N4SSS N4SST Does not meet JIC requirements 2 Flat panel

5 48 Series Single Door Aluminum Enclosures - NEMA 4 Continuous Hinge, Clamped Cover Inner Panel Included Wallmount Enclosures Application Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures. Provides protection where equipment may be hosed down or otherwise be very wet, or in specific applications where corrosion may be a problem. Standards UL 508 Type 4 and 2 as marked CSA Type 4 and 2 Complies with NEMA Type 4, 2 and 3 JIC EGP--967 IEC 529, IP66 Construction Formed from 0.0" Type 5052 H-32 aluminum. Smooth, continuously welded seams without knockouts, cutouts or holes. Door and body stiffeners are provided in the larger enclosures for extra rigidity. Welded brackets provide for enclosure mounting. Formed lip on door and enclosure excludes flowing liquids and contaminants. Aluminum continuous hinge on door may be removed by pulling the aluminum hinge pin. Door is secured with easily operated aluminum clamps. Provision for padlocking. Oil resistant gaskets are permanently secured. A removable 2 gauge inner panel is included. Collar studs are provided for mounting inner panels. A bonding stud is provided on the door and a grounding stud is provided in the enclosure. A literature pocket is provided for the inside of the door. Finish Cover and enclosure are natural unfinished aluminum. Removable inner panel is finished in white powder coating. Accessories Additional inner panels...see page 384 Breather kits...see page 374 Door stop kits...see page 393 Heaters...see page Lock kit...see page 379 Terminal kit assemblies...see page 386 Thermostats...see page 374 Window kits...see page 39

6 48 Series Single Door Aluminum Enclosures - NEMA 4 Continuous Hinge, Clamped Cover ➊ ➋ ➎ ➏ Front View ➌ ➍ ➐ Section X-X Wallmount Enclosures Section Z-Z ➊ Vertical stiffener required on M only. ➋ Omit center body stiffener if A is less than 4". ➌ Padlocking hasp and staple ➍ Omit 2 middle studs if A is less than 3". ➎ Omit body stiffeners if A or B is less than 29". ➏ Omit 2 middle studs if B is less than 3". ➐ Omit door stiffener if A or B is less than 3". Section Y-Y Panel Size Mtg. Centers Ship Part No. A B C D E F G Wt. lbs. 48N4ALB6, N4ALC6, N4ALE N4ALJ N4ALK N4ALM N4ALS N4ALC0, N4ALE N4ALK N4ALM N4ALT Meets UL standards 2 Flat panel When A= M=

7 Wallmount Enclosures 48 Series Single Door Enclosures - NEMA 2, 3 Continuous Hinge, Clamped Cover Application Designed to house electrical, electronic, hydraulic or pneumatic controls and instruments. Provides a degree of protection from falling dirt, dust, oil and water. Standards UL 508 Type 2 and 3 CSA Type 2 and 3 Complies with NEMA Type 2 and 3 JIC EGP--967 unless marked IEC 529, IP65 Construction Formed 4 gauge steel bodies and doors. Smooth, continuously welded seams without knockouts, cutouts or holes. Door and body stiffeners are provided in the larger enclosures for extra rigidity. Welded brackets provide for enclosure mounting. Formed lip on door and enclosure exclude flowing liquids and contaminants. Continuously hinged door may be removed by pulling the hinge pin. Door is secured with easily operated stainless steel clamps. Provision for padlocking. Oil resistant gaskets are permanently secured and mechanically retained. A removable 2 gauge inner panel is included. Collar studs are provided for mounting inner panels. A bonding stud is provided on the door and a grounding stud is provided in the enclosure. A literature pocket is provided for the inside of the door. Inner Panel Included Finish Cover and enclosure are finished in recoatable smooth ANSI/ASA 6 gray powder coating on the outside, with white powder coating on the inside. Removable inner panel is finished in white powder coating. Accessories Additional inner panels...see page 384 Air conditioners...see page Blowers...see page 359 Breather kits...see page 374 Door clamping hardware...see page 378 Door stop kits...see page 393 Drip shield kits...see page 393 Enclosure stabilizers...see page 397 Filter fans...see page Floor stand kits...see page 394 Heaters...see page Lock kit...see page 379 Louvered ventilating plates...see page 396 Quick release clamp...see page 378 Terminal kit assemblies...see page 386 Thermostats...see page 374 Window kits...see page 39 Panel Size Centers Ship Part No. A B C D E F G Wt. lbs 48A B G CR CA C D ER AR H E J FG F K L M A B G CR CA C Does not meet JIC requirements 2 Flat Panel Panel Size Centers Ship Part No. A B C D E F G Wt. lbs 48D ER AR H E J KR KA KG F K KK MR L M LL N O P Q R S T Does not meet JIC requirements 2 Flat Panel

8 48 Series Single Door Enclosures - NEMA 2, 3 Continuous Hinge, Clamped Cover ➐ ➊ ➍ ➋ ➎ ➏ Front View Top View ➌ ➑ Section Z-Z WHEN A= M= ➊ Vertical stiffener required on KK, M, MR and LL only. ➋ Omit center body stiffener if A is less than 4". ➌ Padlocking hasp and staple. ➍ Omit 2 middle studs if A is less than 3". ➎ Omit body stiffeners if A or B is less than 29". ➏ Omit 2 middle studs if B is less than 3". ➐ Omit door stiffener if A or B is less than 3" except if AxB is 42"x30", 48"x30" or 72"x30". ➑ Omit if A is less than 48". Panel Size Centers Ship Part No. A B C D E F G Wt. lbs 48B C D AR E J F K L M O P R S T C E J K KK L M LL O P S T U V E J K M P S T U K M S T U K U Does not meet JIC requirements 2 Flat Panel Wallmount Enclosures

9 48 N4 Series Single Door Enclosures - NEMA 2, 4 Continuous Hinge, Clamped Cover Inner Panel Included Wallmount Enclosures Application Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures. Provides protection where equipment may be hosed down or otherwise be very wet, or in outdoor applications for full weather protection. Standards UL 508 Type 3R,2, 4 CSA Type 3R, 2, 4 Complies with NEMA Type 3R, 4, 2 and 3 JIC EGP--967 unless marked IEC 529, IP66 Construction Formed 4 gauge steel bodies and doors. Smooth, continuously welded seams without knockouts, cutouts or holes. Door and body stiffeners are provided in the larger enclosures for extra rigidity. Welded brackets provide for enclosure mounting. Formed lip on door and enclosure exclude flowing liquids and contaminants. Stainless steel continuous hinge on door may be removed by pulling the stainless steel hinge pin. Door is secured with easily operated stainless steel clamps. Provision for padlocking. Oil resistant gaskets are permanently secured and mechanically retained. A removable 2 gauge inner panel is included. Collar studs are provided for mounting inner panels. A bonding stud is provided on the door and a grounding stud is provided in the enclosure. A literature pocket is provided for the inside of the door. Finish Cover and enclosure are finished in recoatable smooth ANSI/ASA 6 gray powder coating. Removable inner panel is finished in white powder coating. Accessories Additional inner panels...see page 384 Air conditioners...see page Blowers...see page 359 Breather kits...see page 374 Door clamping hardware...see page 378 Door stop kits...see page 393 Drip shield kits...see page 393 Enclosure stabilizers...see page 397 Filter fans...see page Floor stand kits...see page 394 Heaters...see page Lock kit...see page 379 Louvered ventilating plates...see page 396 Quick release clamp...see page 378 Terminal kit assemblies...see page 386 Thermostats...see page 374 Window kits...see page 39

10 48 N4 Series Single Door Enclosures - NEMA 2, 4 Continuous Hinge, Clamped Cover ➊ ➍ ➋ ➎ ➏ Front View ➌ ➐ ➊ Vertical stiffener required on KK and M only. ➋ Omit center body stiffener if A is less than 4". ➌ Padlocking hasp and staple. ➍ Omit 2 middle studs if A is less than 3". ➎ Omit body stiffeners if A or B is less than 29". ➏ Omit 2 middle studs if B is less than 3". ➐ Omit door stiffener if A or B is less than 3" except if AxB is 42"x30" or 48"x30". Wallmount Enclosures When A= M= Section Z-Z Section Y-Y Literature pocket supplied loose. Number of door clamps varies to enclosure size. Panel Size Mtg. Centers Ship Part No. A B C D E F G Wt. lbs. 48N4B N4G N4CR N4C N4D N4AR N4H N4E N4J N4F N4K N4L N4B N4C N4D N4ER N4E N4J N4KR N4F N4K N4KK N4L Does not meet JIC requirements 2 Flat Panel Panel Size Mtg. Centers Ship Part No. A B C D E F G Wt. lbs. 48N4M N4O N4P N4S N4T N4C N4E N4K N4M N4R N4S N4T N4E N4K N4L N4M N4P N4S N4K N4M N4S N4T Does not meet JIC requirements 2 Flat Panel

11 48 Series Single Door Freestanding Enclosures - NEMA 2 Single or Dual Access Order Panel Separately Freestanding Enclosures Application Designed to house electrical, electronic, hydraulic or pneumatic controls with provision for panel mounting or rack mounting of equipment. Provides a degree of protection from falling dirt, dust, oil and water. Available with front access only or both front and rear access. A variety of inner panels, rack mounting rails and swing out frames are available to provide flexibility in mounting arrangements. Standards UL 508 Type 2 CSA Type 2 Complies with NEMA Type 2 IEC 529, IP65 Construction Formed 2 gauge steel. Smooth, continuously welded seams without knockouts, cutouts or holes. Lifting eyes provide for easy enclosure handling. Doors are supported with heavy gauge continuous hinges. Doors are secured with a three point latch and operated with a key locking automotive type handle. Latch rods are equipped with rollers for easier door closing. Oil resistant gaskets are permanently secured and mechanically retained. Mounting channels are welded on the inside of the enclosure for mounting of optional inner panels or rack equipment rails. A grounding stud is provided in the enclosure and a bonding stud is provided on the door. A literature pocket is provided for the inside of the door (Two pockets are provided for dual access units). Finish Cover and enclosure are finished in recoatable smooth ANSI/ASA 6 gray powder coating on the outside, with white powder coating on the inside. Optional inner panels, rails, frames and supports are finished in white powder coating. Accessories Air conditioners...see page Blowers...see page 359 Breather kits...see page 374 Door stop kits...see page 393 Drip shield kits...see page 393 Filter fans...see page Heaters...see page Inner panels...see page 64 Light kit...see page 393 Louvered ventilating plates...see page 396 Panel rails...see page 65 Swing frames...see page 65 Thermostats...see page 374 Window kits...see page 39

12 48 Series Single Door Freestanding Enclosures - NEMA 2 Single or Dual Access Freestanding Enclosures Single Access- Front View Single Access- Dual Access- Front View Dual Access- Note: 4 eyebolts are provided for 30.06" and 36.06" deep enclosures (both dual and single access) Single Access Optional Ship Full Wt. Part No. A B C F G Panel lbs. 48TW TWFW 20 48W WFW X XFW Y YFW YW YWFW 33 48YY YFW TY TYFW W WFW X XFW Y YFW YY YFW W WFW Y YFW W WFW Y YFW YY YFW 525 Refers to Optional Full Height/Full Width Panels. Depth Panels & Half Height Width panels are also available...see page 64. Dual Access Optional Ship Full Wt. Part No. A B C F G Panel lbs. 48WD WFW XD XFW YD YFW YYD YFW WD WFW WD WFW YD YFW YYD YFW 555 Refers to Optional Full Height/Full Width Panels. Depth Panels & Half Height Width panels are also available...see page 64. Maximum Useable Depth Single Access only From inside surface of front door to front face of Full Width Panel Inner Panel in Full Back Position Enclosure Depth (In.) Maximum Usable Depth

13 48 Series Two Door Freestanding Enclosures - NEMA 2 Single or Dual Access Order Panel Separately Freestanding Enclosures Application Designed to house electrical, electronic, hydraulic or pneumatic controls with provision for panel mounting or rack mounting of equipment. Provides a degree of protection from falling dirt, dust, oil and water. Available with front access only or both front and rear access. A variety of inner panels, rack mounting angles and swing frames are available to provide flexibility in equipment mounting. Standards UL 508 Type 2 CSA Type 2 Complies with NEMA Type 2 IEC 529, IP65 Construction Formed 2 gauge steel (0 gauge on back of single access enclosures). Smooth, continuously welded seams without knockouts, cutouts or holes. Stiffeners on the rear of the enclosure provide rigidity. Lifting eyes provide for easy enclosure handling. Doors are supported with heavy gauge continuous hinges. Doors are secured with a three point latch and operated with a key locking automotive type handle. Latch rods are equipped with rollers for easier door closing. Oil resistant gaskets are permanently secured and mechanically retained. Mounting channels are welded on the inside of the enclosure for mounting of optional inner panels or rack equipment rails. A bonding stud is provided on the door and a grounding stud is provided in the enclosure for each door. A literature pocket is provided for the inside of the door (Two pockets are provided for dual access units). Finish Cover and enclosure are finished in recoatable smooth ANSI/ASA 6 gray powder coating on the outside, with white powder coating on the inside. Optional inner panels, rails, frames and supports are finished in white powder coating. Accessories Air conditioners...see page Blowers...see page 359 Breather kits...see page 374 Center panel support...see page 64 Door stop kits...see page 393 Drip shield kits...see page 393 Filter fans...see page Heaters...see page Inner panels...see page 64 Light kit...see page 393 Louvered ventilating plates...see page 396 Panel rails...see page 65 Swing frames...see page 64 Thermostats...see page 374 Window kits...see page 39

14 48 Series Two Door Freestanding Enclosures - NEMA 2 Single or Dual Access Freestanding Enclosures Single or Dual Access - Front View Single Access- Dual Access- Note: 4 eyebolts are provided for 36.06" deep enclosures (both dual and single access) Single Access Optional Ship Full Wt. Part No. A B C F G Panel lbs. 48AW AWFW ZW ZWFW ZX ZXFW ZY ZYFW BW BWFW BY BYFW BY BYFW ZW ZWFW ZX ZXFW ZY ZYFW ZX ZXFW BY BYFW 00 Refers to Optional Full Height/Full Width Panels. Depth Panels & Half Height Width panels are also available...see page 64. Dual Access Optional Ship Full Wt. Part No. A B C F G Panel lbs. 48ZWD ZWFW ZXD ZXFW ZYD ZYFW BYD BYFW ZXD ZXFW 900 Refers to Optional Full Height/Full Width Panels. Depth Panels & Half Height Width panels are also available...see page 64.

15 48 N4 Series Freestanding Enclosures - NEMA 4, 2 Single Door Order Panel Separately Freestanding Enclosures Application Designed to house electrical, electronic, hydraulic or pneumatic controls with provision for panel mounting or rack mounting of equipment. Provides protection where equipment may be hosed down or otherwise be very wet, or in specific applications where corrosion is a serious problem. A variety of inner panels, rack mounting rails and swing out frames are available to provide flexibility in mounting arrangements. Standards UL 508 Type 3R, 4 and 2 CSA Type 3R, 4 and 2 Complies with NEMA Type 3R, 4, 2 and 3 IEC 529, IP66 Construction Formed 2 gauge steel. Smooth, continuously welded seams without knockouts, cutouts or holes. Lifting eyes provide for easy enclosure handling. Doors are supported with heavy gauge continuous hinges. Doors are secured with heavy duty stainless steel clamps. Oil resistant gaskets are permanently secured and mechanically retained. Mounting channels are welded on the inside of the enclosure for mounting of optional inner panels or rack equipment rails. A grounding stud is provided in the enclosure and a bonding stud is provided on the door. Finish Cover and enclosure are finished in recoatable smooth ANSI/ASA 6 gray powder coating on the outside, with white powder coating on the inside. Optional inner panels are finished in white powder coating. Accessories Air conditioners...see page Breather kits...see page 374 Door stop kits...see page 393 Drip shield kits...see page 393 Filter fans...see page Heaters...see page Light kit...see page 393 Panel rails...see page 65 Inner panels...see page 64 Swing frames...see page 65 Thermostats...see page 374 Window kits...see page 39

16 48 N4 Series Freestanding Enclosures - NEMA 4, 2 Single Door Lip Detail Top Horizontal Freestanding Enclosures Vertical Cross Section Front View Cross Section Strut Detail Right Side Top View Optional Ship Wt. Part No. A B C Full Panel lbs. 48N4W WFW N4X XFW N4Y YFW 390 Refers to Optional Full Height/Full Width Panels. Depth Panels & Half Height Width panels are also available...see page 64.