Type 4 Panel Enclosures

Transcription

1 Type 4 Free-Standing ata Sheet Finish Wash and phosphate undercoat ANSI 61 gray polyester powder finish Accessories Full and half panels Side and swing panels Channel mounting hardware Equipment rack mounts Touch-up paint See Accessories section Application Houses electrical controls and instruments Easy access panels or rack mounts for housing optional equipment Intended for indoor or outdoor use Protects against windblown dust and rain, splashing water and hose directed water Standards UL 508A listed, Type 4 and Type 12 CSA C22.2 No.94 certified, Type 4 and Type 12 Conforms to NEMA standard for Type 4 and Type 12 E.I.A. RS-310- Construction Enclosure and door are fabricated from (12) gauge steel All continuous welded seams are finished smooth oor is secured to the body with removable concealed hinges and easy to remove stainless steel door clamps on three (3) sides Modern bevel profile on hinge side of enclosure door oor has a seamless poured in-place gasket Ground stud provided on door and body Each door has a padlock hasp with sealing hole provision Print pocket provided Large lifting eyebolts are supplied Mounting channels are welded inside for locating panels or rack mount equipment along enclosure depth A variety of optional panels and accessories are available (see accessories pages ) iscount Schedule: C2 Subclass: L0 Enclosure Enclosure Size Height x Width x epth A x B x C Catalog Number in. mm in. mm FS x x x 635 x FS x x x 787 x FS x x x 940 x FS x x x 635 x FS x x x 787 x FS x x x 940 x Notes: We can provide special sizes, finishes and other modifications. Consult the factory for your special requirements. 170

2 Type 4 Free-Standing Illustration Sheet and Catalog Number Top View B I I = Inside imension lifting eye C I B-2.64 (67) A I B-3.63 (92) A-7.50 (190) padlock hasp print pocket (supplied) door clamp (see note on this page) 8.87 (225) 4.28 (109) mounting channel 5.35* (136) Front View * From flange opening to bottom of enclosure Side View Notes: Two lifting eyes are furnished on each enclosure. Clamps are mounted along three sides of the enclosure door. Spacing between clamps along side opposite the hinge does not exceed 15 inches. imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. 171

3 Type 4 Free-Standing with Quarter-Turn Latches ata Sheet and Catalog Number Finish Wash and phosphate undercoat ANSI 61 gray polyester powder finish Accessories Full and half panels Side and swing panels Panel Support Kit Panel Lifting Kit Channel mounting hardware Equipment Rack Mounts Lights Window kits Application Houses electrical controls and instruments Easy access panels or rack mounts for housing optional equipment Intended for indoor or outdoor use Protects against windblown dust and rain, splashing water and hose directed water Standards UL 508A listed, Type 4 and Type 12 CSA C22.2 No.94 certified, Type 4 and Type 12 Conforms to NEMA standard for Type 3, Type 4, Type 12 E.I.A. RS-310- Construction Enclosure body (12) gauge and door (14) gauge are fabricated from steel All continuous welded seams are finished smooth oor is secured to the body with removable concealed hinges and quarter-turn flush latches on three (3) sides Modern bevel profile on both sides of enclosure door oor has a seamless poured in-place gasket Formed lip around enclosure opening diverts liquids and contaminants Ground stud provided on door and body Print pocket provided Mounting channels are welded inside for locating panels or rack-mount equipment along enclosure depth Provision for mounting flourescent light Large lifting eyebolts iscount Schedule: C2 Subclass: L2 Enclosure Enclosure Size Height x Width x epth A x B x C Catalog Number in. mm in. mm FSQT 72 x 24 x x 609 x FSQT 72 x 30 x x 762 x FSQT 72 x 36 x x 914 x Notes: We can provide special sizes, finishes and other modifications. Consult the factory for your special requirements. 172

4 Type 4 Free-Standing with Quarter-Turn Latches Illustration Sheet I = Inside imension B I C I lifting eye B-1.62 (41) B-2.75 (70) X X A-6.63 (168) quarter-turn latches A I print pocket (supplied) 6.08 (154) 8.87 (225) Front View 5.35* (136) mounting channel * From flange opening to bottom of enclosure Side View Section X-X Notes: Two lifting eyes are furnished on each enclosure. imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. 173

5 Type 4 Single oor Free-Standing with 3-Point Locking ata Sheet Application Houses electrical controls and instruments Easy access panels or rack mounts for housing optional equipment Intended for indoor or outdoor use Protects against windblown dust and rain, splashing water and hose directed water Standards UL 508A listed, Type 4 and Type 12 CSA C22.2 No.94 certified, Type 4 and Type 12 Conforms to NEMA standard for Type 3, 4, 12 E.I.A. RS-310- Finish Wash and phosphate undercoat ANSI 61 gray polyester powder finish Accessories Full and half panels Side and swing panels Panel Support Kit Panel Lifting Kit Channel mounting hardware Equipment Rack Mounts Lights Window kits Replacement handle, B-PKHB, (see page 429) Construction Enclosure and door are fabricated from (12) gauge steel All continuous welded seams are finished smooth oor is secured to the body with removable concealed hinges and a center locating 3-point key-locking and padlock handle mechanism Additional quarter turn latches provided at the top and bottom on all enclosure doors Modern bevel profile on both sides of enclosure door oor has a seamless poured in-place gasket Formed lip around enclosure opening diverts liquids and contaminants Ground stud provided on door and body Print pocket provided Mounting channels are welded inside for locating panels or rack-mount equipment along enclosure depth Provision for mounting flourescent light Large lifting eyebolts iscount Schedule: C2 Subclass: L3 Enclosure Enclosure Size Height x Width x epth A x B x C Catalog Number in. mm in. mm FS3PT 60 x 24 x x 609 x FS3PT 72 x 24 x x 609 x FS3PT 72 x 30 x x 762 x FS3PT 72 x 36 x x 914 x FS3PT 90 x 24 x x 610 x FS3PT 90 x 36 x x 914 x FS3PT 60 x 36 x x 914 x FS3PT 72 x 24 x x 609 x FS3PT 72 x 30 x x 762 x FS3PT 72 x 36 x x 914 x FS3PT 90 x 36 x x 914 x FS3PT 72 x 24 x x 609 x FS3PT 72 x 36 x x 914 x FS3PT 72 x 36 x x 914 x FS3PT 90 x 36 x x 914 x Notes: We can provide special sizes, finishes and other modifications. Consult the factory for your special requirements. 174

6 Type 4 Single oor Free-Standing with 3-Point Locking Illustration Sheet and Catalog Number I = Inside imension B I lifting eye C I B-1.62 (41) X X B-2.75 (70) 3-point handle lock A I A-6.63 (168) print pocket (supplied) rotation 5.35* (136) mounting channel 8.87 (225) Front View * From flange opening to bottom of enclosure Side View Section X-X Notes: Four lifting eyes are furnished when C dimension is 30 (762 mm) or larger. imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. 175

7 Type 4 Single-oor ual-access Free-Standing with 3-Point Locking ata Sheet Application Houses electrical controls and instruments Easy access panels or rack mounts for housing optional equipment Intended for indoor or outdoor use Protects against windblown dust and rain, splashing water and hose directed water Standards UL 508A listed, Type 4 and Type 12 CSA C22.2 No.94 certified, Type 4 and Type 12 Conforms to NEMA standard for Type 3, 4, 12 E.I.A. RS-310- Finish Wash and phosphate undercoat ANSI 61 gray polyester powder finish Accessories Full and half panels Side and swing panels Panel Support Kit Panel Lifting Kit Channel mounting hardware Equipment Rack Mounts Lights Window kits Replacement handle, B-PKHB, (see page 429) Construction Enclosure and doors are fabricated from (12) gauge steel All continuous welded seams are finished smooth oor is secured to the body with removable concealed hinges and a center locating 3-point key-locking and padlock handle mechanism Additional quarter turn latches provided at the top and bottom on all enclosure doors Modern bevel profile on both sides of enclosure door oor has a seamless poured in-place gasket Formed lip around enclosure opening diverts liquids and contaminants Ground stud provided on door and body Print pocket provided Mounting channels are welded inside for locating panels or rack-mount equipment along enclosure depth Provision for mounting flourescent light Large lifting eyebolts iscount Schedule: C2 Subclass: L3 Notes: We can provide special sizes, finishes and other modifications. Consult the factory for your special requirements. 176

8 Type 4 Single-oor ual-access Free-Standing with 3-Point Locking Illustration Sheet and Catalog Number Enclosure Enclosure Size Catalog Number Height x Width x epth ANSI 61 Gray A x B x C Carbon Steel in. mm in. mm FSA3PT x x x 610 x FSA3PT x x x 762 x FSA3PT x x x 914 x FSA3PT x x x 914 x FSA3PT x x x 610 x FSA3PT x x x 610 x FSA3PT x x x 914 x FSA3PT x x x 914 x I = Inside imension B-1.62 (41) Top View B I mounting channel lifting eye C I B-2.75 (70) 3-point keylocking and padlock handle A I A (168) print pocket (supplied) rotation 8.87 (225) 5.35* (136) Front View * From flange opening to bottom of enclosure Side View Notes: Four lifting eyes are furnished when C dimensions is (762 mm) or more. imensions are in inches. Millimeters shown are for reference only. ata subject to change without notice. 177