CONCEPT Wall-Mount Enclosure Accessories

Transcription

1 CONCEPT Wall-Mount Enclosure Accessories The CONCEPT Enclosure Group Accessory Selection Guide Steel section 4 or Stainless Steel Enclosures section 6 Steel section 4 or Stainless Steel Window-Door Enclosures section 6 Flush-Mount Enclosures section 4 Two-Door Enclosures section 4 Steel section 5 or Stainless Steel Disconnect Enclosures section 6 Internal Accessories Door Accessories External Accessories Steel Panel Adjustable Depth Mounting Kit Door Stop Kit Pole Mounting Kit Swing-Out Panel Panel Conversion Kit Mounting Channels Data Pocket Handles and Latches Mounting Foot Kit DIN Rail Kit Key Inserts Swing-Out Rack Frame Grid Straps Dead Front Kit Rack Mounting Angles Data subject to change without notice FAX Hoffman Enclosures Inc.

2 Panels These panels are taller and wider than corresponding NEMA-size panels. Panels are 14 or 12 gauge steel and are painted white. Swing-Out Panels Panels swing clear from front of enclosure to provide access to mounted internal equipment. Maximum 106 degree panel swing. Distance from panel surface to door when in the latched position is 1.71 (43) for solid doors and 1.45 (37) for window doors. Kit includes 14 gauge panel, brackets, and hardware that can be mounted to front flange. Swing-out panels meet NEMA Type 1 with enclosure door open. NOTE: Swing-out panel can also be mounted on front-to-back adjustable rails. Adjustable Depth Mounting Kits These kits provide mounting means for installing panels, swing-out panels, DIN rails, rack angles, mounting channels, or grid straps at any depth from front to rear of enclosure. Kits include slide channels that fit 6-, 8-, 10-, or 12-inch deep enclosures (qty. 4 or 2), slide mechanisms, and hardware. Use two kits when enclosure has 6 collar studs for mounting panel. NOTE: Dead front panel and swing-out rack frame cannot be mounted on adjustable mounting kit. Number Fits CONCEPT enclosure CAM64 when C 6.00 (152) with 4 corner collar studs CAM84 when C 8.00 (203) with 4 corner collar studs CAM82 when C 8.00 (203) with 2 addl. collar studs CAM104 when C (254) with 4 corner collar studs CAM102 when C (254) with 2 addl. collar studs CAM124 when C (305) with 4 corner collar studs CAM122 Bulletins A53, CW1 Steel ZincPlated Panel Size D x E Number Number inch (millimeter) Gauge CP1212 CP1212G x (259 x 259) 14 CP1612 CP1612G x (361 x 259) 14 CP1616 CP1616G x (361 x 361) 12 CP2016 CP2016G x (462 x 361) 12 CP x (564 x 361) 12 CP x (462 x 462) 12 CP2420 CP2420G x (564 x 462) 12 CP x (716 x 462) 12 CP2424 CP2424G x (564 x 564) 12 CP3024 CP3024G x (716 x 564) 12 CP3624 CP3624G x (869 x 564) 12 CP x (1173 x 564) 12 CP x (716 x 716) 12 CP3630 CP3630G x (869 x 716) 12 CP4230➊ x (1021 x 716) 12 CP x (869 x 869) 12 CP x (1021 x 869) 12 CP x (1173 x 869) 12 CP x (1478 x 869) 12 CP x (564 x 1021) 12 CP x (716 x 1173) 12 CP x (716 x 1478) 12 ➊ Used on Concept disconnect enclosures. Panel Size Height x Width Fits Number inch (millimeter) A x B CSP x 9.84 (248 x 250) 12 x 12 CSP x 9.84 (350 x 250) 16 x 12 CSP x (350 x 352) 16 x 16 CSP x (452 x 352) 20 x 16 CSP x (553 x 352) 24 x 16 CSP x (350 x 453) 16 x 20 CSP x (452 x 453) 20 x 20 CSP x (553 x 453) 24 x 20 CSP x (706 x 453) 30 x 20 CSP x (452 x 555) 20 x 24 CSP x (553 x 555) 24 x 24 CSP x (706 x 555) 30 x 24 CSP x (858 x 555) 36 x 24 CSP x (706 x 707) 30 x 30 CSP x (858 x 707) 36 x 30 CSP x (858 x 860) 36 x 36 Millimeter dimensions ( ) are for reference only; do not convert metric to inch. when C (305) with 2 addl. collar studs 12 General Accessories CONCEPT Wall-Mount Enclosure Accessories Data subject to change without notice FAX Hoffman Enclosures Inc

3 Internal Accessories Panel Conversion Kit Kit adapts enclosure for mounting standard NEMA-size panels in CONCEPT enclosures. Bracket attaches to rear collar stud. Using a smaller NEMA-size panel provides space behind and at the sides of the panel for wire management. Kit includes four adapter plates and hardware for mounting panel. Number Fits CONCEPT enclosure CCPM4 when A x B x (762 x 762) Dead Front Kits Kits provide a NEMA Type 1 safety barrier and mounting surface close to the front of the enclosure. Enable convenient mounting of equipment while controlling access to the interior of the enclosure.the depth from the mounting surface to the door is 1.33 (34) for solid doors and 1.15 (29) for window doors. Kits include mounting brackets, grounding hardware, and a steel panel painted with ANSI 61 gray polyester powder paint. NOTE: Dead front kits cannot be mounted on adjustable mounting kit.) Mounting Channels Channels provide mounting framework for installing DIN rails and grid straps at various positions within the enclosure. Channels can be mounted vertically or horizontally to collar studs or to the slide mechanisms of the adjustable mounting kit. Each kit includes two channels. Number Fits CONCEPT enclosure A x B CDF x (305 x 305) CDF x (406 x 305) CDF x (508 x 406) CDF x (508 x 508) CDF x (610 x 508) CDF x (610 x 610) CDF x (762 x 610) Number Fits CONCEPT enclosure CMC12 when A or B = (305) CMC16 when A or B = (406) CMC20 when A or B = (508) CMC24 when A or B = (610) CMC30 when A or B = (762) CMC36 when A or B = (914) CMC42 when A or B = (1067) CMC48 when A or B = (1219) CMC60 when A or B = (1524) DIN3 Rail Kit DIN3 rails supply mounting surfaces for DIN mount snap-on devices. Rails attach vertically or horizontally to rear collar stud or to mounting channels. Kit includes three rails and mounting hardware. Fits CONCEPT Number Description enclosure CDR3P12 DIN 3 Symmetric when A or B = profile TS35x (305) CDR3P16 DIN 3 Symmetric when A or B = profile TS35x (406) CDR3P20 DIN 3 Symmetric when A or B = profile TS35x (508) CDR3P24 DIN 3 Symmetric when A or B = profile TS35x (610) Data subject to change without notice FAX Hoffman Enclosures Inc.

4 Grid Straps Grid straps provide a flexible mounting means inside the enclosure. Available in single-hole or three-hole widths. Straps mount vertically or horizontally on rear collar studs or to mounting channels in any front-to-back position.two straps and mounting hardware included in kit. (Order separate grid fastener package catalog number XGFM6, consisting of 20 metric M6 clip nuts and 20 metric M6 Phillips washer head bolts, for mounting equipment to grid straps.) Bulletin CW1 Number Description Fits CONCEPT enclosure CGS112 1 hole width when A or B = (305) CGS116 1 hole width when A or B = (406) CGS120 1 hole width when A or B = (508) CGS124 1 hole width when A or B = (610) CGS130 1 hole width when A or B = (762) CGS336 3 hole width when A or B = (914) CGS342 3 hole width when A or B = (1067) CGS348 3 hole width when A or B = (1219) CGS360 3 hole width when A or B = (1524) 12 General Accessories Rack Mounting Angles Rack mounting angles allow mounting 19-inch rack equipment in 24-inch wide enclosures. L-shaped thru-hole angles attach to enclosure flange or the adjustable mounting kit. Holes are.281 (7) in diameter. Clear zinc plated 14 gauge steel construction. Mounting hardware included. Order separately clip nut package catalog number XNM5 and screws XSM5 (metric) or AN1032 and screws AS1032 (English). Swing-Out Rack Frames These frames provide 120 degree swing-out access for 19-inch rack equipment.welded rack frame mounts to front flange. Distance from frame to door surface is 1.32 (33) for solid doors and 1.07 (27) for window doors. Frame is steel painted with ANSI 61 gray polyester powder paint. Mounting hinge and latching hardware provided. Order separately clip nut package catalog number ANM5 and screws ASM5 (metric) or AN1032 and screws AS1032 (English). NOTE: Swing-out rack frame cannot be mounted on adjustable mounting kit. Number Fits CONCEPT enclosure Units CRA10TH when A = (508) 10 CRA12TH when A = (610) 12 CRA16TH when A = (762) 16 CRA19TH when A = (914) 19 CRA26TH when A = (1219) 26 Fits CONCEPT enclosure Number A x B Units CSF x (610 x 610) 11 CSF x (762 x 610) 15 CSF x (914 x 610) 18 CONCEPT Wall-Mount Enclosure Accessories Data subject to change without notice FAX Hoffman Enclosures Inc

5 Internal Accessories, Handles, Locks, Mounting Kit Door Stop Kit Door stop secures the door in the open position. Can be installed at the top or bottom of a door which opens horizontally. Door opening angle can be easily adjusted by means of a wing nut. Stop arm slides neatly out of the way when the door is closed.all parts are zinc plated. Mounting hardware included. Maintains ULCSA Type 4 and Type 12 if properly installed in a Hoffman enclosure. NOTE: Door Stop Kit is not intended for use on CONCEPT window door enclosures, or on enclosures configured with a swing-out panel or swing-out rack frame. Number Fits CONCEPT enclosure ADSTOPK when B (406) Data Pockets Data pockets provide convenient storage for documentation inside an enclosure. Pockets mount on studs located on the inside of a solid door enclosure. Constructed of high impact thermoplastic, pockets are dark gray and have cutout areas for easy access and visibility to contents. Mounting hardware included. Fits CONCEPT Number Length x Width enclosure ADP x 6.00 when A < 30 (152 x 152) and 16 B 24 ADP x when A 30 and (305 x 305) B 20 or when A >24 and B > 30 Mounting Bracket Kits Mounting brackets are field installable. Composite and stainless steel brackets are rated to Type 4X. Composite brackets are rated for 500 lbs. maximum load. All hardware is included. Four brackets per kit. Number CMTGFT CMFK CMFKSS Description Composite mounting bracket kit Steel zinc plated mounting bracket kit Stainless steel (Type 304) mounting bracket kit Data subject to change without notice FAX Hoffman Enclosures Inc.

6 Handles These handles replace the standard slotted insert on all CONCEPT wall-mount enclosures.the CONCEPT non-locking handle provides quick and easy access to the enclosure contents. Handle is black plastic. A zinc die-cast keylock handle is available for applications requiring quick access and security. A padlocking handle, also zinc plated, accommodates a padlock with up to a 5 /16-inch locking bar. Each latch system can be converted from clockwise to counter-clockwise opening. Keylocking style patents 360,345 (U.S.) DE M (Germany) Locking Door Handle 5,664,448 (U.S.) Bulletin CW1 Number Description CWHNL a Nonlocking handle b CWHK Keylock handle CWHPTO a Padlock handle a Handles maintain UL 508A, 508 Type 3, Type 4, Type 4X, and Type 12 when properly installed on a Hoffman enclosure. b Not suitable for 3-point latch operation. 12 General Accessories Key Inserts Key inserts can be easily substituted for the standard slot/screwdriver insert latch. Inserts have a chrome finish. Matching key is zinc die-cast. Pole Mounting Kits Pole mounting kits enable CONCEPT enclosures to be mounted to poles of various sizes and shapes. Simply attach the galvanized steel channel bar to the mounting holes at the back of the enclosure and wrap the stainless steel strap around the pole and through the bar. Kit includes two mounting channels, two straps suitable for 3 in. to 12 in. diameter pole, and mounting hardware. Number Description CLKTM7 Triangular 7mm insert with key CLKSM7 Square 7mm insert with key CLKDBM3 Double bit with key Number Fits CONCEPT enclosure CPMK12 when B = (305) CPMK16 when B = (406) CPMK20 when B = (508) CPMK24 when B = (610) CPMK30 when B = (762) CONCEPT Wall-Mount Enclosure Accessories Data subject to change without notice FAX Hoffman Enclosures Inc