CZ-200P PG500 PCT-300. General Description. Features. Resin Pressure Measuring System CZ-200P. Resin Pressure Sensor CZ-200P

Transcription

1 P5 P5 5 Resin Pressure Measuring System Z-2P Z-2P P5 PT-3 eneral escription Resin pressure indicator P5 Resin pressure sensor : Z-2P Output converter : PT-3 RK's resin pressure measuring system is suitable for monitoring and control of resin pressure for extruders. The combination of resin pressure sensor (Z-2P), the resin pressure indicator (P5), the converter (PT-3) to the improvement of productivity and quality of products. The Z-2P has new features such as built-in thermocouple while retaining high reliability of Z-1P. The features of Z-2P includes a wide selection of screw type, UF, PF and M14/16 type screws, ow pressure type ( to.5mpa, to 1MPa), built-in thermocouple. push-rod method is used in Z-2P. There is no risk of mercury contamination in case of accident, so Z-2P suits food processing application. Features Resin Pressure Sensor Z-2P The total loop accuracy of.5% (combination with RK converter PT-3) High reliability and stability Wide selection of the range from 1MPa to 15MPa Various screw types, UF, PF and M14/16 Optional built-in thermocouple Supports high temperatures (SPRO iaphragm Type) SPRO diaphragm with a maximum operating temperature of 55 and excellent corrosion resistance on the level of Hastelloy has been added to our lineup. Suitable for pressure measurement of high-function resins (high-temperature melted resins) such as polymer resins. * 45 when using a J-type thermocouple temperature sensor. Max.55 Output onverter PT-3 Signal converter for Z-2P Up to four analog s inearization function Resin Pressure Indicator P5 Easy-to-read large E 1msec sampling cycle time Optional communication (RS422/RS-485), retransmission, up to two alarms M1 M2 O1 M3 O2 M4 O3 O4 MPa MPa Resin pressure indicator P5 SET ontroller hart recorder etc. 1. mv/v MOI ZERO PWR PT-3 M1 M2 O1 M3 O2 M4 O3 O4 SET MPa Temperature indicator 5 Output converters PT-3 Z2_4E 1

2 Resin Pressure Measuring System Z-2P Resin Pressure Sensor Z-2P onstruction 4 sides adhered strain gauge type wheatstone bridge Rated Pressure eneral specification: to 1, to 2, to 35, to 5, to 7 MPa to 1 MPa High pressure type : to 15 MPa (Z-2P-H type only) ow pressure type : to 1, to 5 MPa (Z-2P- type only) Rated Output : 1. to 1.8mV/V [ t 15 of diaphragm temperature] *1 SPRO type (ode : P) : t 25 ridge Impressed Voltage : 1V (at PT-3, T-3) 7.7V (at P5, REX-P41) ccuracy : inearity : Hysteresis : Reproducibility : Zero alance : ridge Resistance : SUS63 type ( t 15 of diaphragm temperature) Within ±1% of full scale Within ±2% of full scale (Over 7 MPa ) SPRO type ess than 7MPa : Within ±1% of full scale More than 48 of 1,2,7MPa More than 1MPa More than 48 of 1MPa HSTEOY type : ontact to RK SUS63 type ( t 15 of diaphragm temperature) Within ±1% of full scale Within ±2% of full scale (Over 7 MPa ) SPRO type ess than 7MPa : Within ±1% of full scale More than 48 of 1,2,7MPa More than 1MPa More than 48 of 1MPa HSTEOY type : ontact to RK SUS63 type Within ±.5% of full scale Within ±1% of full scale (Over 5 MPa ) Within ±2% of full scale (Over 7 MPa ) Within ±.2% of full scale (1MPa type) SPRO type ess than 7MPa : Within ±1% of full scale More than 48 of 1,2,7MPa More than 1MPa More than 48 of 1MPa HSTEOY type : ontact to RK Within ±.2% of span More than 48 of 1,2MPa :Within ±2% of full scale ±.6mV/V (Within ±4% of span) 35Ω±5Ω (Input resistance) 35Ω±5Ω (Output resistance) *2 llowable Maximum Temperature of the iaphragm : 4 (SPRO type : 55 ) llowable Maximum Temperature of the Strain auge : 2 *3 Zero Point Temperature Effect (To the temperature of the diaphragm) SUS63 type : ±.2%/1 ±.3%/1 (1MPa, 15MPa) SPRO type :.1±.2%/1 HSTEOY type : ontact to RK Output Temperature Effect Output temperature effect is an equal value as zero point. SPRO type :.15±.2%/1 Effect of Wind (Without lead pipe cover) Within ±1% of full scale (at wind of 4m/sec) llowable Overload : Within 12% of rated pressure Within 5% of rated pressure (1MPa type) Within 1% of rated pressure (.5MPa type) <Temperature Sensor Function> Sensor type : : K or J ( Ungrounded junction, lass2) Maximum Temperature : 55 ( K), 45 ( J) Response time : pprox. 9 sec (room temperature to 1, 98 % response) able length : 1mm (Standard, Maximum length 1 m ) Temperature detection position : Internally 2mm from a diaphragm Output onverter PT-3 Input RK's resin pressure sensor Z-2P (Z-1P) ain Setting Setting range : 1. to mv/v Setting accuracy : Within ±.2% of full scale Output umber of points : Up to 4 points (standard : 2 points) Output Signal o.1 : to 1V (oad resistance : More than 2kΩ) o.2 : to 1mV (oad resistance : More than 1kΩ) o.3 : 1 to 5V (oad resistance : More than 1kΩ) o.4 : 4 to 2m (oad resistance : ess than 6Ω) < eneral > Supply Voltage 9 to 264V (Including supply voltage variation) [Rating : 1 to 24V ] (5/6Hz common use) Power onsumption ess than 12.5V Operating Environments to 5 [32 to 122 F], 45 to 85% RH et Weight pprox. 29g External imensions (W x H x ) 96 x 48 x 1mm Marginal Overload : Within 15% of rated pressure Within 1% of rated pressure (1MPa type) ead Pipe over material : SUS63 Recommended Tightenibg Torque : Fixed nut type: 3 m (3 kgf cm) oose nut type: 6 m (6 kg cm) Output effect of tightening torque : Within ±.2% of full scale (at recommended tightening torque) M14, PF1/4, 1/2-UF screw type : ±1% *1 The of each sensor becomes a specific value within the range of 1. to 1.8 mv/v. *2 s the input side of bridge resistance, the 374Ω±1Ω type is also available. This type is interchangeable with the 35Ω±5Ω type. *3 When the temperature at the bottom of outer tube (nut side) is more than 18, the temperature at the strain gauge exceed 2. If the temperature at the strain gauge exceed 2, the performance cannot be assured. Therefore, cover the heat source with a heat insulating material so that the above temperature does not exceed 2. The temperature at the strain gauge can be expected not to rise when: the long type of sensor is used or the sensor is installed a slant or transversely. 2 If any of the above measures can be taken, take it. Z2_4E

3 Resin Pressure Measuring System Z-2P Resin Pressure Indicator P5 Input Strain gauge type pressure sensor a) Pressure sensor gain setting range :.5 to 1.999mV/V -6.mV to 15.9mV (Including zero point adjustment range) b) Pressure sensor gain setting range : 1. to 1.999mV/V -9.8mV to 25.9mV (Including zero point adjustment range) c) Pressure sensor gain setting range : 2. to 2.999mV/V -12.3mV to 32.6mV (Including zero point adjustment range) d) Pressure sensor gain setting range : 3. to 4.mV/V -16.1mV to 42.5mV (Including zero point adjustment range) ain Setting a) ain setting decimal point position: Three decimal place, Four decimal place b) Setting range:.5 to 4.mV/V (Three decimal place).5 to mV/V Four decimal place) Shunt resistance value 4. to 1.% (Functions when a resistance for sensitivity adjustment built-in pressure sensor is used) Input impedance : More than 1MΩ Input break action : Up-scale/own-scale (Selectable) Sensor power supply : 7.7V ±3% (Within 3m ) Sampling Time :.1 sec. Input adjustment a) Zero point adjustment 1.Manual setting : -Input span to +Input span 2.uto-zero function : -5. to +5.mV (Input conversion) b) Ratio setting 1. Manual setting (ain adjustment setting) :.5 to utomatic calibration function uto calibration is used to automatically set the PV ratio so that the measured value (PV) will be the pressure of the shunt resistance value. (Functions when a resistance for sensitivity adjustment built-in pressure sensor is used) c) inearize : Use to correct the non-linear nature of pressure sensor Z-1P/Z-2P. Select the linearizing type symbol engraved on the rated nameplate attached to the Z-1P or Z-2P housing. d) igital filter :. to 1. sec (OFF when is set.) Input ccuracy : ± (.1% of full scale + 1 digit) Influence of ambient temperature a) Input : ±.6% of Input span/ b) Sensor power supply : ±.13% of Output span/ 4 isplay : 5-digits (The most significant digit : -1 or 1) < Standard function > ontact Input umber of input : Function : 3 points, on-voltage contact input (OPE : 5kΩ or more, OSE : 1Ω or less) I1 : uto-zero I2: Hold reset, I3 : larm interlock reset Hold Function Peak hold : Holds maximum pressure value ottom hold : Holds minimum pressure value The held values can be reset manually, by external contact signal or by communication after the confirmation by the operator. ata is not backed up when the instrument power supply is off. < Optional function > nalog Output umber of point : Output signal : Output accuracy : Output resolution : 1 point (PV value) a) to 1V, to 5V, 1 to 5V, to 1V oad resistance : More than 1kΩ Output impedance : ess than.1ω b) to 1mV, to 1mV oad resistance : More than 2kΩ) Output impedance : ess than 1Ω c) 4 to 2m, to 2m oad resistance : ess than 6Ω Output impedance : More than 1MΩ ±.1% of span More than 12 bits larm Output umber of points : Up to 4 points larm action : High or low alarm (vailable for hold function) Output : Relay, Form contact, 25V.5 (resistive load) Other functions : a) Energized/de-energized action is configurable. b) elay timer :. to 6. sec) c) Interlock (latch) function is configurable. < eneral > Waterproof/ustproof EM4X, IP66 Waterproof/ustproof protection only effective from the front in panel mounted installation. Supply Voltage a) 9 to 264V (Including supply voltage variation) [Rating : 1 to 24V ] (5/6Hz common use) b) 21.6 to 26.4V (Including supply voltage variation) [Rating : 24V ] (5/6Hz common use) c) 21.6 to 26.4V (Ripple rate 1% p-p or less) [Rating : 24V ] Power onsumption ess than 1V (1 to 24V ) ess than 7.V (24V ) ess than 21m (24V ) Rush urrent ess than 12 Memory ackup acked up by non-volatile memory (FRM) ata retaining period : pprox. 1 years umber of writing : pprox. 1,,, times. (epending on storage and operating conditions.) Insulation resistance More than 2MΩ (5V ) between measured terminals and ground More than 2MΩ (5V ) between power terminals and ground ielectric voltage 15V for one minute between measured terminals and ground 15V for one minute between power terminals and ground Operating Environments -1 to +5 [14 to 122 F], 5 to 95% RH (on condensing) et Weight pprox. 2g External imensions (W x H x ) 96 x 48 x 6mm igital ommunications ommunication method : RS-422 (4-wire), RS-485 (2-wire) a) SI X3.28 sub-category 2.54 (RK standard) b) MOUS-RTU Selectable ommunication speed : 12, 24, 48, 96, 192 PS it format : Start bit : 1 ata bit : 7 or 8 MOUS 8 bits only Parity bit : Without, Odd or Even Stop bit : 1 or 2 Maximum connection : 31 units Z2_4E 3

4 Resin Pressure Measuring System Z-2P Intrinsic Safety Intrinsically Safe Explosionproof onstruction Resin Pressure Meter (For Indoor, outdoor) The qualification o. of the intrinsically safe explosionproof construction resin pressure meter obtained from the ministry of abor, Japan, is T55821 (For indoor use) T56658 (For outdoor use). The explosion class and ignition group of the objective gases and steam are i23. The qualified consists of the pressure sensor Z-2P and safety barrier (RZ-1), but the converter is not subject to qualification testing as a general sending/receiving instrument. For indoor use, the standard or the waterproof can be selected. For outdoor use, the waterproof must be used. Resin Pressure Sensor Z-2P Safety arrier onstruction 4 sides adhered strain gauge type wheatstone bridge Rated Pressure eneral specification: to 1, to 2, to 35, to 5, to 7 MPa to 1 MPa High pressure type : to 15 MPa (Z-2P-H type only) ow pressure type : to 1, to 5 MPa (Z-2P- type only) Rated Output : 1. to 1.8mV/V [ t 15 of diaphragm temperature] *1 SPRO type (ode : P) : t 25 ridge Impressed Voltage : 1V (at PT-3, T-3) 7.7V (at P5, REX-P41) ccuracy : SUS63 type ( t 15 of diaphragm temperature) Within ±1% of full scale Within ±2% of full scale (Over 7 MPa ) SPRO type ess than 7MPa : Within ±1% of full scale More than 48 of 1,2,7MPa More than 1MPa More than 48 of 1MPa HSTEOY type : ontact to RK inearity : SUS63 type ( t 15 of diaphragm temperature) Within ±1% of full scale Within ±2% of full scale (Over 7 MPa ) SPRO type ess than 7MPa : Within ±1% of full scale More than 48 of 1,2,7MPa More than 1MPa More than 48 of 1MPa HSTEOY type : ontact to RK Hysteresis : SUS63 type Within ±.5% of full scale Within ±1% of full scale (Over 5 MPa ) Within ±2% of full scale (Over 7 MPa ) Within ±.2% of full scale (1MPa type) SPRO type ess than 7MPa : Within ±1% of full scale More than 48 of 1,2,7MPa More than 1MPa More than 48 of 1MPa HSTEOY type : ontact to RK Reproducibility : Within ±.2% of span More than 48 of 1,2MPa :Within ±2% of full scale Zero alance : ridge Resistance : ±.6mV/V (Within ±4% of span) 35Ω±5Ω (Input resistance) 35Ω±5Ω (Output resistance) *2 llowable Maximum Temperature of the iaphragm : 4 (SPRO type : 55 ) llowable Maximum Temperature of the Strain auge : 2 *3 Zero Point Temperature Effect (To the temperature of the diaphragm) SUS63 type : ±.2%/1 ±.3%/1 (1MPa, 15MPa) SPRO type :.1±.2%/1 HSTEOY type : ontact to RK Output Temperature Effect Output temperature effect is an equal value as zero point. SPRO type :.15±.2%/1 Effect of Wind (Without lead pipe cover) Within ±1% of full scale (at wind of 4m/sec) llowable Overload : Marginal Overload : Within 12% of rated pressure Within 5% of rated pressure (1MPa type) Within 1% of rated pressure (.5MPa type) Within 15% of rated pressure Within 1% of rated pressure (1MPa type) ead Pipe over material : SUS63 Recommended Tightenibg Torque : Fixed nut type: 3 m (3 kgf cm) oose nut type: 6 m (6 kg cm) Output effect of tightening torque : Within ±.2% of full scale (at recommended tightening torque) M14, PF1/4, 1/2-UF screw type : ±1% *1 The of each sensor becomes a specific value within the range of 1. to 1.8 mv/v. *2 s the input side of bridge resistance, the 374Ω±1Ω type is also available. This type is interchangeable with the 35Ω±5Ω type. *3 When the temperature at the bottom of outer tube (nut side) is more than 18, the temperature at the strain gauge exceed 2. If the temperature at the strain gauge exceed 2, the performance cannot be assured. Therefore, cover the heat source with a heat insulating material so that the above temperature does not exceed 2. The temperature at the strain gauge can be expected not to rise when: the long type of sensor is used or the sensor is installed a slant or transversely. If any of the above measures can be taken, take it. <Temperature Sensor Function> Sensor type : : K or J ( Ungrounded junction, lass2) Maximum Temperature : 55 ( K), 45 ( J) Response time : pprox. 9 sec (room temperature to 1, 98 % response) able length : 1mm (Standard, Maximum length 1 m ) Temperature detection position : Internally 2mm from a diaphragm Explosionproof construction Use rated Rating for maintaining safety llowable inductance llowable capacitance mbient temperature mbient humidity over usbar round requirement Weight Terminal onfiguration compensating lead on-hazard area terminal Hazard area terminal compensating lead : Intrinsically safe explosionproof construction (i23) : Power supply circuit 9V 5m, Signal circuit 6V 5m, circuit 6V 5m : 25V,5/6Hz,25V : Wiring between the resin pressure sensor and safety barrier :.6 mh or less : Wiring between the resin pressure sensor and safety barrier :.1μF or less : -1 to +4 (14 to 14 F) : 45 to 85% RH (on condensing) : Iron (oating) : rass (ickel plating) : round this safety barrier so that its grounding resistance will be less than the grounding reference resistance value of shunt diode type safety barriers (e.g. less than 1Ω) conforming to each national standard. (Requirements) : pprox. 85g MOE:RZ-1 External imensions 66 2-R2.5 External Wiring Hazard area Resin pressure sensor (Z-1P,Z-2P) To converter side 4-core shielded cable 4-core shielded cable To resin pressure sensor side MOE:RZ Red rown lue lack Red White E (RZ-1,RZ-1) 43 on-hazard area Safety barrier Red rown lue lack Red White over usber 27 round terminals (To ground) Shielded wire terminal E EX+ EX- SI+ SI- + - onverter or Indicator Recorder or Indicator (5, PT-3) Unit:mm round 4 Z2_4E

5 Model and Suffix ode Z-2P Model Screw type oad-pipe length iaphragm material iaphragm surface treatment Intrinsically safe Pressure range inearization function ead-pipe cover able connection *1 Safety arrier Resin Pressure Measuring System Z-2P Model and Suffix ode Z-2P Fixed nut type PF3/8 oose nut type PF3/4 Tip diameter : 1mm Tip diameter : 18mm H Fixed nut type 1/2-2UF Tip diameter : 7.8mm U Fixed nut type PF1/2 Fixed nut type PF1/4 Fixed nut type M14X1.5 Tip diameter : 1mm Tip diameter : 7.8mm Tip diameter : 1mm J V W Under nut : =12mm Under nut : =15mm Under nut : =18mm Under nut : =21mm ot available for SPRO type SUS63 (Standard) Hastelloy S H SPRO P Standard eramic kanigen plating ot available for SPRO type K on-intrinsic safety (Standard) Intrinsic safety (For indoor use) Intrinsic safety (For outdoor use) H See Pressure Range ode Table ot supplied For P5/REX-P41 (vailable for P41 with S/ 98 or later) For PT-3 (PT-3 should have linearization function) ot supplied ot available for SPRO and fixed nut type *3 With lead-pipe cover Standard type ot available for SPRO type Waterproof, type, equivalent to IP67 (ot available for built-in sensor type or SPRO type) waterproof, direct connection type, equivalent to IP67 (ot available for built-in sensor type) ot supplied Temperature sensor K type thermocouple (ot available for waterproof ) J type thermocouple (ot available for waterproof ) lead length *2 Standard 1mm (Possible to specify by each 1mm. Maximum 1m.) *1 : inearization function is not available for pressure range of - 7MPa or more. inearization function is not available for hastelloy diaphragm. *2 : The model code after "* " is not necessary if there is no option specified after " * ".: *3 : For a fixed nut type with a SPRO diaphragm, the lead-pipe cover is always included. *4 :The cable length on the SUS63 (standard) with a Hastelloy diaphragm is 3 m. Please specify whether or not a flexible cover tube is to be included. Pressure Range ode Table * ( ) : Range code Range Fixed nut type to 1MPa (1P), to 2MPa (2P), to 35MPa (35P), to 5MPa (5P), to 7MPa (7P), to 1MPa (1P), to 15MPa (15P)*1 *2 to 1MPa (1P), to 2MPa (2P), to 3MPa(3P), to 5MPa (5P), to 1MPa (1P), to 2MPa (2P), to 35MPa (3P), to 5MPa (5P), oose nut type to 7MPa (7P), to 1MPa (1P) *1 For pressure range of - 15MPa, only the SUS63 diaphragm is available. *2 For pressure range of -.5MPa with loose nut and the range of - 5Mpa with fixed nut, contact RK agent. (Rated :.5 to.9mv/v, Special amplifier type) Minimum range of HSTEOY and SPRO diaphragm are 1MPa. able for ompensation wire (Stainless steel shielded cable) able for Pressure Standard Type Z-2P Z-2P Z-2P Temperature controller/indicator (ength : 5m) For cables with specifications other than those below, please Please contact RK agent. P5 (ength : 5m) : Y-shaped terminal lugs (M3) PT-3 (ength : 5m) : Y-shaped terminal lugs (M3) T-3 (ength : 5m) : Plug The letter in the indicates the cable coating type. Select from the three types below. : Heat-resistant glass coated cable, V: Vinyl coated cable, S :Silicon coated cable Heat-resistant glass coated cable Silicon coated cable Heat-resistant glass coated cable Silicon coated cable Type K Type J T *4 P Q K J Model ode W--K2EX-TM-Y3-5 W--J2EX-TM-Y3-5 W-- -P-5 W--S -P-5 W-- -PP-5 W--S -PP-5 Specification Model ode Specification Model ode Intrinsic Safety (For indoor) RZ-11 Intrinsically safe circuit side (Hazard area) Intrinsic Safety (uilt-in thermocouple circuit, For indoor) RZ-11 Z-2P RZ-1 (5m) W--Y-P-5 Intrinsic Safety (For outdoor) RZ-12 onnection cable on-intrinsically safe circuit side (on hazard area) Intrinsic Safety (uilt-in thermocouple circuit, For outdoor) W--V--1 RZ-12 RZ-1 5 (1m) or PT-3(1m) This product has passed the qualification test of intrinsically safe explosion proof when combined with our resin pressure sensor (Z-1P/Z-2P). lways combine and use this product with our resin pressure sensor. Z2_4E 5

6 Resin Pressure Measuring System Z-2P Model and Suffix ode P5 o. Model and Suffix ode P5 Standard type Intrinsic safety type Input type Standard type (oose ut :. to.5mpa,fixed ut : to 5MPa) Intrinsic safety type (oose ut :. to.5mpa,fixed ut : to 5MPa) For 3.33mV/V type Power supply 1 to 24V 24V / larm ot supplied umber of alarm (Specify 1 to 4) nalog ot supplied See nalog Output Signal ode Table, ode : 1 to 8) ot supplied ommunication RS-422 RS-485 Initial setting o quick start code (efault setting) Specify quick start code larm 1 See larm ode Table larm 2 See larm ode Table larm 3 See larm ode Table larm 4 See larm ode Table Terminal cover (Sold separately) Model ode : KF4-58 Hardware coding only Quick start code X nalog Output Signal ode Table 1-1mV 2-1mV 3-1V 4-5V 5-1V 6 1-5V H J K 7 8 larm ode Table - 2m 4-2m o alarm Process High Process ow Process High with larm Hold Process ow with larm Hold PT-3 Model Type umber of Option Model and Suffix ode PT-3 Standard type 2 s ( to 1V, to 1mV ) 3 s ( to 1V, to 1mV, 1 to 5V ) 4 s ( to 1V, to 1mV, 1 to 5V, 4 to 2m ) ot supplied ain change switch ( x1 or x2) inearization function Supply Voltage 1-24V 6 Z2_4E

7 Resin Pressure Measuring System Z-2P External imensions and Rear Terminals (Unit : mm) For fixed nut type (Z-2P-H type) onnector receptacle PR F Outer tube Flat head diameter of hexagon nut : 23 iaphragm PF3/8 (JIS grade) ø21 ø ø1 ø14 Mounting hole (Unit : mm) ø1.3±.1 ø15.2±.1 MP1- ø38 ø Flexible tube (pprox.1mm) otted-line section : imensions of lead-pipe cover (Option) 3 ø2 Standard dimensions and weight Weight H pprox.43g PF3/8 H pprox.47g Element finished to JIS grade. H pprox.51g Install the sensor so that each H pprox.55g screw is smoothly inserted. The dimension can be up to a maximum of 25 mm. (Please contact RK agent) For loose nut type (Z-2P- type) onnector receptacle PR F Outer tube Flat head bolt 14 type snap ring Flat head diameter of iaphragm hexagon nut : 23 PF3/4 (JIS grade) -.1 ø ø Mounting hole (Unit : mm) ø18.3±.1 ø24.5±.1 MP1- Flexible tube (pprox.1mm) ø38 ø ø3 Standard dimensions and weight Weight pprox.76g pprox.85g pprox.94g pprox.13g The dimension can be up to a maximum of 23 mm. (Please contact RK agent) PF3/4 Element finished to JIS grade. Install the sensor so that each screw is smoothly inserted. For fixed nut type unified thread (Z-2P-U type) MP1- onnector receptacle PR F Flexible tube (pprox.1mm) ø38 ø17 13 Outer tube 75 Flat head diameter of hexagon nut : /2-2UF-2 ø21 4 iaphragm otted-line section : imensions of lead-pipe cover (Option) ø14.6 ø ø ø Standard dimensions and weight U U U U Weight pprox.41g pprox.45g pprox.49g pprox.53g Mounting hole (Unit : mm) ø18 ø14 The dimension can be up to a maximum of 25 mm. (Please contact RK agent) 1/2-2UF-2 9 ø8 -.1 ø11.5 Element finished to JIS grade. Install the sensor so that each screw is smoothly inserted. When the diaphragm material is SPRO, the cable type is direct connection. Jack PR F Flexible jacked cable (Stainless ø12.5) 3 Heat shrinkage tube *1 3 ap Flat head bolt 22 ø38 Outer tube In the case of a loose nut type or fixed nut type unified screws, the outer tube and cable are as shown at left. Mounting hole dimensions are the same as on the standard product. Unit dimensions are the same as the dimensions of the standard product; however, the lead unit () dimension 12 mm (H,, U) is not possible. *2 75 The fixed-nut type is only available with a lead-pipe cover. 5 (Standard) * 1,3 is available Reference : Screw dimension tolerances lass MP1- Flexible tube (pprox.1mm) Screw type JIS grade (lass 2, 2) Inner diameter tolerances of female screw to JIS grade (lass 2, 2) Effective diameter tolerances of female screw to +.25 *1 With thermocouple : ø2 Without thermocouple : ø26 *2 With thermocouple : 12 Without thermocouple : 15 PF1/4,PF3/8 PF1/2,PF3/4 M14 x 1.5, M16 x 1.5 1/2-2UF to to to +.3 to +.15 to to Z2_4E 7

8 Resin Pressure Measuring System Z-2P External imensions PT-3 Unit:mm 91 (1) Unit : mm SH EX+ EX- SI+ SI mV 96-1V Panel cutout nalog Sensor input V 1-5V 4-2m round Power supply nalog nalog P5 Unit:mm Use a solderless terminal for screw size M3X SH EX+ EX- SI+ SI- (Red) (rown)(lue)(lack) OM I 1 I 2 I 3 Z-2P Z-1P 48 Panel cutout <lose vertical mounting> * Up to 6 units igital input Sensor input S T() T() R() R() O RS-422 S T/R()T/R() RS-485 ommunication nalog OM OM 1-24V O O O + - O M1 M2 M3 M4 24V (Panel thickness must be between 1 to 1mm) =(48Xn-3) +.6 n : umber of controllers (2=<n=<6) Waterproof/dustproof is not available for close horizontal mounting. 24V Power supply larm 1, 2 Relay contact larm 3, 4 alibration 8 Z2_4E