AST46HA Factory Sealed Gauge / ASIC
|
|
- Hollie Jones
- 6 years ago
- Views:
Transcription
1 AST46HA Factory Sealed Gauge / ASI Explosionproof Transmitter SA Approved For Hazardous Locations Overview AST46HA high accuracy Explosionproof Transducer/Transmitter is SA approved for use in hazardous areas including: SA 30 (UL1203/FM3615) lass 1 Zone 1 Group II SA 30 lass 1 Div 1 Groups A, B,, D Explosionproof SA 30 lass 2 Div 1 Groups E, F, G Dust Ignition-proof Applying digital compensation, this product offers top performance over a wide temperature range. Utilizing Krystal Bond Technology, the sensing element will measure pressure in the most extreme temperature conditions. Where other sensor technologies will freeze or boil, the AST46HA uses a one piece stainless steel sensor to offer continuous operation. NOW APPROVED SINGLE SEAL ANSI / ISA Benefits ANSI/ISA ertified Single Seal (no secondary seal required) ABS (American Bureau of Shipping) Approved ASI ompensation Superb Temperature Performance Wide Operating Temperature Excellent Accuracy High Proof and Burst s from 100 to 20,000 PSI (Factory Sealed Gauge)* Available in Exotic Alloys (onsult Factory for Inconel 718 or Hastelloy 276) Applications Well Optimization Oil and Gas Pipelines Drilling Platforms Marine & Offshore * For pressures over 1,000 PSI, see AST46HA Vented Gauge data sheet. For pressures less than 100 PSI, see AST4600 Vented Gauge data sheet. 25 (77 F) Accuracy** Stability (1 year) Over Range Protection Burst ycles <±0.1% BFSL ±0.1% FS, typical 2X Rated, standard 5X or 50,000 PSI, whichever is less >100 Million NG / Hydrogen Fill Stations Paint Booths Remote Telemetry Unit old limate Drilling & Mining ** Accuracy Includes: non-linearity, hysteresis, and non-repeatability For higher proof pressures, contact factory US Environmental Data A P P R O V E D Krystal Bond P R O D U Technology by AST Temperature Operating Ambient -40 to 85 (-40 to 185 F) Operating Media -55 to 125 (-65 to 250 F) Storage -50 to 105 (-58 to 221 F) Thermal Limits ompensated Range -20 to 70 (-4 to 158 F) T Zero: <±0.5% FS T Span: <±0.5% FS Other Shock EN Vibration EN , , and IE EMI/RFI Protection: Yes Rating: IP-66 T Electrical Data Output 4-20mA 0-5V, 1-5V, 1-6V 0-10V, 1-10V V Ratiometric Excitation 10-28VD 10-28VD 15-30VD 5VD, Regulated urrent onsumption - <10mA <10mA <10mA Sampling Rate 400Hz 400Hz 400Hz 400Hz Output Noise <1mV, RMS <1mV, RMS <1mV, RMS <1mV, RMS Zero Offset <±0.5% FS <±0.5% FS <±0.5% FS <±0.5% FS Span Tolerance <±0.5% FS <±0.5% FS <±0.5% FS <±0.5% FS Output Load Ohms@10-28VD 5k Ohms, min. 5k Ohms, min. 5k Ohms, min. Reverse Polarity Protection Yes Yes Yes Yes American Sensor Technologies 450 lark Dr., Mt. Olive, NJ phone (973) fax (973) info@astsensors.com
2 Ordering Information AST46HA AST4600 A W P P 34 T 11 H Process onnection (for A= 1/4 other Male ports NPT* contact factory) A= I= 1/4 NPT Female* Male* I= P= 1/4 1/2 NPT Male* Female* P= W= 1/2 F250 NPT Female Male* Autoclave (>10,000 PSI) W= F250 Female Autoclave (>10,000 Range PSI) Insert pressure code from chart Range Unit Insert 5 digit pressure range code from chart B= Bar K= kg/cm2 P= PSI Outputs Unit 1= V ratiometric 5= 0-10V (3 wire) B= 2= 0-5V BAR (3 wire) K=kg/cm2 P=PSI 6= 1-6V (3 wire case connection) Outputs 3= 1-5V (3 wire case connection) G= 1-10V 3= 4= 4-20mA 1-5V (3 (loop Wire powered ase onnection) case connection) 4= 4-20mA (Loop Powered ase onnection) 6= T= 2 1-6V ft. 18 (3 AWG Wire wires ase U= onnection) 4 ft. 18 AWG wires W= 2 Meter 18 AWG wires Electrical Wetted Material Interface T= 0= 17-4PH 2ft. 18 AWG 1= wires 316L* U= 2= 4ft. Inconel 18 AWG 718** wires 4= Hastelloy W= 2 Meter 276** 18 AWG wires Ranges in PSIS ode , , , , , , , , , For gauge pressure units, see AST46HA Vented Gauge data sheet. Absolute ranges available, contact factory. Wetted Failure State Material 0= H= 17-4PH High L= 2= Low Inconel N= None 718** 1= 316 L* 4= Hastelloy 276** *Available up to 10,000 PSI, **onsult factory on availability Dimensional Data Output Red Black White Green For U.S. installations, sensor case ground Voltage V Supply -V Supply Output ase Ground (green wire) must be bonded to ground 4-20mA V Supply -V Supply Not Used ase Ground according to Article 501 & 505 of the NE. Warranty Workmanship - AST, Inc. pressure transmitters have a limited one-year warranty to the original purchaser. AST, Inc. will replace or repair, free of charge, any defective transmitter. This warranty does not apply to any units that have been modified; misused, neglected or installed where the application exceeds published ratings. AST s sensors are made with pride in New Jersey, USA. If in the area please feel free to stop by for a visit! Installation/Applications - The purchaser is responsible for media compatibility, functional adequacy, and correct installation of the transmitter American Sensor Technologies Inc. AST46HA-Sealed 12/18/12. All specifications subject to change without notice.
3 AST46HA Vented Gauge / ASI Explosionproof Transmitter SA Approved For Hazardous Locations Overview AST46HA high accuracy Explosionproof Transducer/Transmitter is SA approved for use in hazardous areas including: SA 30 (UL1203/FM3615) lass 1 Zone 1 Group II SA 30 lass 1 Div 1 Groups A, B,, D Explosionproof Applying digital compensation, this product offers top performance over a wide temperature range. Utilizing Krystal Bond Technology, the sensing element will measure pressure in the most extreme temperature conditions. Where other sensor technologies will freeze or boil, the AST46HA uses a one piece stainless steel sensor to offer continuous operation. Benefits ANSI/ISA ertified Single Seal (no secondary seal required) ABS (American Bureau of Shipping) Approved ASI ompensation Superb Temperature Performance Wide Operating Temperature Excellent Accuracy High Proof and Burst s from 1 to 1,000 PSI Gauge* Available in Exotic Alloys (onsult Factory for Inconel 718 or Hastelloy 276) Applications Industrial Well Optimization OEM & Hydrogen Equipment NG / Hydrogen Instrumentation Fill Stations Natural Oil and Gas Gas Pipelines ompressors Oil Paint Platforms Booths Refrigeration Drilling Platforms Well Remote Head Telemetry Unit Pipe Line Instrumentation Power Generation Panel Instrumentation old limate Drilling & Mining Marine & Offshore Mining Applications * For pressures over 1,000 PSI, see AST46HA Factory Sealed Gauge data sheet. For pressures less than 100 PSI, see AST4600 Vented Gauge data sheet. 25 (77 F) Accuracy** Stability (1 year) Over range Protection Burst ycles <±0.1% BFSL ±0.1% FS, typical 2X Rated, standard 5X Rated >100 Million ** Accuracy Includes: non-linearity, hysteresis, and non-repeatability For higher proof pressures, contact factory NOW APPROVED SINGLE SEAL ANSI / ISA US Environmental Data A P P R O V E D Krystal Bond Technology by AST Temperature Operating Ambient -40 to to 85 (-40 to to 185 F) Operating Media -55 to to 125 (-65 to to 250 F) Storage to to 105 (-67 (-58 to to 221 F) Thermal Limits ompensated Range 0-20 to 55 to 70 (30(-4 to to 130 F) 158 F) T Zero: <±1.5% <±0.5% of FS FS T Span: <±1.5% <±0.5% of FS FS Other Shock EN Vibration EN , , and IE EMI/RFI Protection: Yes Rating: IP-66 IP-65 P R O D U T Electrical Data Output 4-20mA 0-5V, 1-5V, 1-6V 0-10V, 1-10V V Ratiometric Excitation 10-28VD 10-28VD 15-30VD 5VD, Regulated urrent onsumption - <10mA <10mA <10mA Sampling Rate 400Hz 400Hz 400Hz 400Hz Output Noise <1mV, RMS <1mV, RMS <1mV, RMS <1mV, RMS Zero Offset <±0.5% FS <±0.5% FS <±0.5% FS <±0.5% FS Span Tolerance <±0.5% FS <±0.5% FS <±0.5% FS <±0.5% FS Output Load Ohms@10-28VD 5k Ohms, min. 5k Ohms, min. 5k Ohms, min. Reverse Polarity Protection Yes Yes Yes Yes American Sensor Technologies 450 lark Dr., Mt. Olive, NJ phone (973) fax (973) info@astsensors.com
4 Ordering Information AST46HA AST4600 A W G P P 34 T 1 H Process onnection (for A= 1/4 other Male ports NPTcontact factory) A= I= 1/4 NPT NPT Female Male* I= P= 1/4 1/2 NPT Male Female* P= 1/2 NPT Reference Male* W= G= Gauge F250 Female Autoclave (>10,000 V= Gauge PSI) (Vacuum alibrated) Range (Vented Gauge) Insert 4 digit Range pressure range code from chart Insert 5 digit pressure range code from chart Unit B= Bar H= Inches H Unit 2 O K= kg/cm2 P= PSI B= Outputs BAR K=kg/cm2 P=PSI 1= V ratiometric 5= 0-10V (3 wire) Outputs 2= 0-5V (3 wire) 6= 1-6V (3 wire case connection) 3= 1-5V (3 (3 wire Wire case ase connection) onnection) G= 1-10V 4= 4-20mA (loop (Loop powered Powered case ase connection) onnection) 6= 1-6V (3 Wire ase onnection) T= 2 ft. 18 AWG wires U= 4 ft. 18 AWG wires W= 2 Meter 18 AWG wires T= Wetted 2ft. 18 Material AWG wires U= 4ft. 18 AWG wires W= 2 Meter 18 AWG wires 0= 17-4PH 1= 316L 2= Inconel 718* 4= Hastelloy 276* Wetted Material 0= Failure 17-4PH State 2= Inconel 718** 1= H= 316 High L* L= Low 4= Hastelloy N= None 276** Ranges in PSIG Range ode , For sealed pressure units, see AST46HA Factory Sealed Gauge data sheet. 2.5 PSI sensor must be ordered in inches of H 2 O. *onsult factory on availability Dimensional Data Output Red Black White Green For U.S. installations, sensor case ground Voltage V Supply -V Supply Output ase Ground (green wire) must be bonded to ground 4-20mA V Supply -V Supply Not Used ase Ground according to Article 501 & 505 of the NE. Warranty Workmanship - AST, Inc. pressure transmitters have a limited one-year warranty to the original purchaser. AST, Inc. will replace or repair, free of charge, any defective transmitter. This warranty does not apply to any units that have been modified; misused, neglected or installed where the application exceeds published ratings. AST s sensors are made with pride in New Jersey, USA. If in the area please feel free to stop by for a visit! Installation/Applications - The purchaser is responsible for media compatibility, functional adequacy, and correct installation of the transmitter American Sensor Technologies Inc. AST46HA-Vented 12/18/12. All specifications subject to change without notice.
5 AST46PT Factory Sealed Gauge / ASI SA Approved Explosionproof / Temperature Transmitter Overview AST46PT high accuracy Explosionproof /Temperature Transmitter is SA approved for use in hazardous areas including: SA 30 (UL1203/FM3615) lass 1 Zone 1 Group II SA 30 lass 1 Div 1 Groups A, B,, D Explosionproof SA 30 lass 2 Div 1 Groups E, F, G Dust Ignition-proof Applying digital compensation, this product offers top performance over a wide temperature range. Utilizing Krystal Bond Technology, the sensing element will measure pressure in the most extreme temperature conditions. Where other sensor technologies will freeze or boil, the AST46PT uses a one piece stainless steel sensor to offer continuous operation. Benefits ANSI/ISA ertified Single Seal (no secondary seal required) and Temperature Output from One Device ASI ompensation Superb Temperature Performance Wide Operating Temperature Excellent Accuracy High Proof and Burst s from 100 to 20,000 PSI (Factory Sealed Gauge)* Available in Exotic Alloys (onsult Factory for Inconel 718 or Hastelloy 276) Applications Well Optimization Oil and Gas Pipelines Drilling Platforms Marine & Offshore NG / Hydrogen Fill Stations Paint Booths Remote Telemetry Unit old limate Drilling & Mining * For pressures over 1000 PSI, see AST46PT Vented Gauge data sheet. For pressures less than 100 PSI, see AST4600 Vented Gauge data sheet. 25 (77 F) Accuracy** Stability (1 year) Over range Protection Burst ycles <±0.1% BFSL ±0.1% FS, typical 2X Rated, standard 5X or 50,000 PSI, whichever is less > 100 Million **Accuracy Includes: non-linearity, hysteresis, and non-repeatability For higher proof pressures, contact factory NOW APPROVED SINGLE SEAL ANSI / ISA US Environmental Data Krystal Bond Technology by AST Temperature Operating Ambient -40 to 85 (-40 to 185 F) Operating Media -55 to 125 (-65 to 250 F) Storage -50 to 105 (-58 to 221 F) Thermal Limits ompensated Range -20 to 70 (-4 to 158 F) T Zero: <±0.5% FS T Span: <±0.5% FS Other Shock EN Vibration EN , , and IE EMI/RFI Protection: Yes Rating: IP-66 Electrical Data Output 4-20mA 0-5V, 1-5V, 1-6V 0-10V, 1-10V V Ratiometric Excitation 10-28VD 10-28VD 15-30VD 5VD, Regulated urrent onsumption - < 10mA < 10mA < 10mA Sampling Rate 400Hz 400Hz 400Hz 400Hz Output Noise < 1mV, RMS < 1mV, RMS < 1mV, RMS < 1mV, RMS Zero Offset < ± 0.5% FS < ± 0.5% FS < ± 0.5% FS < ± 0.5% FS Span Tolerance < ± 0.5% FS < ± 0.5% FS < ± 0.5% FS < ± 0.5% FS Output Load Ohms@10-28VD 5k Ohms, min. 5k Ohms, min. 5k Ohms, min. Reverse Polarity Protection Yes Yes Yes Yes For units with loop-powered 4-20mA output, the pressure loop must be powered or the temperature output will not operate. American Sensor Technologies 450 lark Dr., Mt. Olive, NJ phone (973) fax (973) info@astsensors.com
6 Ordering Information AST46PT AST A W P 3 P T 41 T H Temperature Output 1= Process -40 to 85 onnection (-40 to 185 F) 2= (for -40 other to 125 ports (-40 contact to 257 F) factory) 3= 0 to 70 (32 to 158 F) A= 1/4 NPT Male* 4= -55 to 125 (-67 to 250 F) 5= I= -18 1/4 to NPT 93 (0-200 F) Female* P= 1/2 NPT Male* Process onnection A= W= 1/4 F250 Male NPT* Female Autoclave I= (>10,000 1/4 NPT Female* PSI) P= 1/2 NPT Male* W= F250 Female Autoclave (10,000-20,000 Range PSI) Insert 5 digit pressure range code from chart Range Insert pressure code from chart Unit Unit B= Bar K= kg/cm2 P= PSI B= BAR K=kg/cm2 P=PSI Outputs 1= Outputs V ratiometric 5= 0-10V (3 wire) 3= 1-5V (3 Wire ase onnection) 3= 1-5V (3 wirecase connection) G= 1-10V 4= 4-20mA 4-20mA (loop(loop poweredcase Powered connection) ase onnection) 6= 1-6V (3 Wire ase onnection) 2= 0-5V (3 wire) 6= 1-6V (3 wirecase connection) T= 2 ft. 18 AWG wires U= 4 ft. 18 AWG wires W= 2 Meter 18 AWG wires T= 2ft. 18 AWG wires U= 4ft. 18 AWG wires W= 2 Meter 18 AWG wires Wetted Material 0= 17-4PH 1= 316L* 2= Inconel 718** 4= Hastelloy 276** Wetted Material Failure State H= 0= High 17-4PH L= Low 2= Inconel N= None718** 1= 316 L* 4= Hastelloy 276** Ranges in PSIS ode , , , , , , , , , For gauge pressure units, see AST46PT Vented Gauge data sheet. Absolute ranges available, contact factory. *Available up to 10,000 PSI, **onsult factory on availability Dimensional Data Table 1 Output Power onnections Output onnections Green Length For U.S. installations, sensor Red Black White Blue case ground (green wire) must be Voltage V Supply -V Supply Temperature ase Ground 4.3" bonded to ground according to 4-20mA - -Temperature Temperature ase Ground 4.8" Article 501 & 505 of the NE. Warranty Workmanship - AST, Inc. pressure transmitters have a limited one-year warranty to the original purchaser. AST, Inc. will replace or repair, free of charge, any defective transmitter. This warranty does not apply to any units that have been modified; misused, neglected or installed where the application exceeds published ratings. AST s sensors are made with pride in New Jersey, USA. If in the area please feel free to stop by for a visit! Installation/Applications - The purchaser is responsible for media compatibility, functional adequacy, and correct installation of the transmitter American Sensor Technologies Inc. AST46PT-Sealed 12/18/12. All specifications subject to change without notice.
7 AST4600 AST46PT Factory Vented Sealed Gauge Gauge / ASI Transducer SA Explosionproof Approved Explosionproof SA Approved For / Hazardous Temperature Locations Transmitter Overview AST4600 AST46PT Explosionproof high accuracy Explosionproof Transducer/Transmitter / Temperature is SA Transmitter approved for is use SA in approved hazardous for areas use in including: hazardous areas including: SA 30 (UL1203/FM3615) lass 1 Zone 1 Group II SA 30 lass 1 Div 1 Groups A, B,, D Explosionproof Applying SA 30 digital lass compensation, 2 Div 1 Groups this E, product F, G Dust offers Ignition-proof top performance over a wide onstructed temperature with range. a simple-yet-rugged Utilizing Krystal Bond design, Technology, the factory-sealed the sensing AST4600 element stands up will to measure a variety pressure of Explosionproof in the most applications extreme temperature where price and conditions. performance Where are other critical. sensor technologies will freeze or boil, the AST46PT uses a one piece stainless Benefits steel sensor to offer continuous operation. Benefits ANSI/ISA ertified Single Seal (no secondary seal required) ABS ANSI/ISA (American Bureau of ertified Shipping) Single Approved Seal (no secondary seal required) All Stainless and Steel Temperature onstruction Output from One Device No ASI Oil-filled ompensation cavities, Welds, or Internal O-rings Wide Superb Operating Temperature Temperature Performance Range Ranges Wide Operating from 100 Temperature to 20,000 PSI (Factory Sealed Gauge)* Low Excellent Static Accuracy and Thermal Errors Rugged High Proof Design and Burst Withstands Harsh Environments Suitable s for from High 1 Shock to 1,000 and PSI Vibration Gauge* Applications Available in Exotic Alloys (onsult Factory for Inconel 718 or Hastelloy 276) Applications Industrial Well Optimization OEM & Hydrogen Equipment Natural Oil and Gas Pipelines ompressors Refrigeration Drilling Platforms Pipe Panel Line Instrumentation Marine & Offshore 25 (77 F) Performance 25 (77 F) Accuracy** <±0.1% BFSL Accuracy** <±0.25% BFSL (<±0.5% BFSL for 7,500 to 20,000 PSI) Stability (1 year) ±0.1% FS, typical Stability (1 year) ±0.25% FS, typical Over range Protection 2X Rated, standard Over Range Protection 2X Rated Burst 5X or 50,000 PSI, whichever is less Burst 5X Rated or 50,000 whichever is less ycles > 100 Million ycles >100 Million **Accuracy Includes: non-linearity, hysteresis, and non-repeatability ** For Accuracy higher proof includes pressures, non-linearity, contact hysteresis factory & non-repeatability Electrical Data NG / Hydrogen Instrumentation Fill Stations Oil Paint Platforms Booths Well Remote Head Telemetry Unit Power old limate Generation Drilling & Mining Mining Applications * For pressures over 1,000 PSI, see AST46PT Factory Sealed Gauge data sheet. For pressures less than 100 PSI, see AST4600 Vented Gauge data sheet. APPROVED NOW SINGLE SEAL / ANSI ANSI ISA Output 4-20mA 4-20mA 0-5V, 1-5V, 1-6V 0-10V, 1-5VD, 1-10V1-6VD V Ratiometric Excitation 10-28VD 10-28VD 10-28VD 15-30VD 10-28VD 5VD, Regulated Output urrent Impedance onsumption - >10k Ohms < 10mA < 10mA <100 Ohms, Nominal < 10mA urrent Sampling onsumption: Rate 400Hz 25mA, typical 400Hz 400Hz 5mA, typical 400Hz Bandwidth Output Noise < 1mV, RMS (-3dB): D to 1kHz < 1mV, RMS < 1mV, (-3dB): RMS D to 1kHz < 1mV, RMS Output Zero Offset Noise: < ± 0.5% FS - < ± 0.5% FS < ± <2mV 0.5% FS RMS < ± 0.5% FS Zero Span Offset: Tolerance < ± 0.5% FS <±1% of FS < ± 0.5% FS < ± <±1% 0.5% FS of FS < ± 0.5% FS Span Output Tolerance: Load Ohms@10-28VD <±2% of FS 5k Ohms, min. 5k Ohms, <±1.5% min. of FS 5k Ohms, min. Output Reverse Load: Polarity Protection Yes Ohms@10-28VD Yes Yes5k Ohms, Min. Yes Krystal Bond Technology Reverse Polarity Protection For units Yeswith loop-powered 4-20mA output, the pressure loop must Yesbe powered or the temperature output will not operate. US Environmental Data P by AST A P P R O V E D Temperature Operating Ambient -40 to to 85 (-40 to to 185 F) Operating Media -55 to to 125 (-65 to to 250 F) Storage to to 105 (-67 (-58 to to 221 F) Thermal Limits ompensated Range 0-20 to 55 to 70 (30(-4 to to 130 F) 158 F) T Zero: <±1.5% <±0.5% of FS FS T Span: <±1.5% <±0.5% of FS FS Other Shock EN Vibration EN EN , , and IE EMI/RFI Protection: Yes Rating: IP-66 IP-65 R O D U T American Sensor Technologies 450 lark Dr., Mt. Olive, NJ phone (973) fax (973) info@astsensors.com
8 Ordering Information AST46PT AST A W G P 3 P T 4 1 T H Temperature Output 1= Process -40 to 85 onnection (-40 to 185 F) 2= (for -40 other to 125 ports (-40 contact to 257 F) factory) 3= 0 to 70 (32 to 158 F) A= 1/4 NPT Male* 4= -55 to 125 (-67 to 250 F) 5= I= -18 1/4 to 93 NPT (0-200 F) Female* Process P= 1/2 onnection NPT Male* A= W= 1/4 F250 Male NPT Female Autoclave I= (>10,000 1/4 NPT Female PSI) P= 1/2 NPT Male Reference Range G= Gauge Insert 5 digit pressure range code from chart V= Gauge (Vacuum alibrated) Range (Vented Gauge) Insert 4 digit pressure Unit code from chart B= BAR K=kg/cm2 P=PSI Unit B= Bar H= Inches H 2 O K= kg/cm2 P= PSI Outputs Outputs 3= 1-5V (3 Wire ase onnection) 1= V ratiometric 5= 0-10V (3 wire) 4= 4-20mA (Loop Powered ase onnection) 6= 1-6V (3 Wire ase onnection) 2= 0-5V (3 wire) 6= 1-6V (3 wirecase connection) 3= 1-5V (3 wirecase connection) G= 1-10V 4= 4-20mA (loop poweredcase connection) T= 2ft. 18 AWG wires U= 4ft. 18 AWG wires W= 2 Meter 18 AWG wires T= 2 ft. 18 AWG wires U= 4 ft. 18 AWG wires W= 2 Meter 18 AWG wires Ranges in PSIG ode , For sealed pressure units, see AST46PT Factory Sealed Gauge data sheet. 2.5 PSI sensor must be ordered in inches of H 2 O. Wetted Material 0= 17-4PH 1= 316L 2= Inconel 718* 4= Hastelloy 276* Wetted Material 0= 17-4PH 2= Inconel 718** Failure 1= 316 State L* 4= Hastelloy 276** H= High L= Low N= None *Available up to 10,000 PSI, **onsult *onsult factory factory on availability on availability Dimensional Data Table 1 Power onnections Output onnections Output Output Red Black White Green Green Length For U.S. installations, sensor Red Black White Blue For U.S. installations, case sensor ground case (green ground wire) must be Voltage Voltage V Supply V -V Supply Supply -V Supply Output Temperaturease ase Ground Ground(green wire) 4.68" must be bonded to to ground according to 4-20mA V Supply -V Supply Not Used ase Ground according to Article Article 501 & of & 505 the of NE. 4-20mA - -Temperature Temperature ase Ground 5.18" the NE. Warranty Workmanship - AST, Inc. pressure transmitters have a limited one-year warranty to the original purchaser. AST, Inc. will replace or repair, free of charge, any defective transmitter. This warranty does not apply to any units that have been modified; misused, neglected or installed where the application exceeds published ratings. AST s sensors are made with pride in New Jersey, USA. If in the area please feel free to stop by for a visit! Installation/Applications - The purchaser is responsible for media compatibility, functional adequacy, and correct installation of the transmitter American Sensor Technologies Inc. AST4600-Sealed AST46PT-Vented 10/02/12. 12/18/12. All specifications subject to change without notice.
9 Model 46SW Explosion-Proof Stainless Steel SPDT Switch Overview The Model 46SW is a high accuracy Explosion-proof Switch, designed for use in a variety of applications. Applying digital compensation, this product offers top performance over a wide temperature range. Utilizing Krystal Bond Technology, the sensing element will measure pressure in the most extreme temperature conditions. Where other sensor technologies will freeze or boil, the AST46SW uses a one piece stainless steel sensor to offer continuous operation. If linearity and repeatability are critical for your application, this product will exceed your expectations at an affordable price. NOW APPROVED SINGLE SEAL ANSI / ISA Benefits SA30 (UL1203 / FM3615) lass I Div 1 and Zone 1 Group II Explosionproof - Groups A, B,, D ANSI Single Seal Approved ASI ompensation Superb Temperature Performance Wide Operating Temperature Excellent Accuracy High Proof and Burst Factory Sealed Applications Well Optimization Oil and Gas Pipelines Drilling Platforms NG / Hydrogen Fill Stations Paint Booths RTU ombustion ontrols US Environmental Data Temperature Operating Storage Thermal Limits Krystal Bond Technology by AST -40 to 85 (-40 to 185 F) -50 to 105 (-58 to 221 F) 25 (77 F) ompensated Range -20 to 70 ( -4 to 158 F) Error Tolerance <±1.0% BFSL of line pressure Other Over range Protection 2X rated line pressure, standard* Shock 100G, 11 msec, 1/2 sine Burst 5X or 60,000PSI of line pressure, whichever is less Vibration 10G peak, 20 to 2000 Hz. ycles > 100 million full pressure cycle EMI/RFI Protection: Yes *For higher proof pressures, contact factory Electrical Data Excitation urrent onsumption 10-28VD <10mA Rating: IP-66 Set Point See hart on page 2 Output Load Reverse Polarity Protection 1 Amp., Resistive Yes American Sensor Technologies 450 lark Dr., Mt. Olive, NJ phone (973) fax (973) info@astsensors.com
10 Ordering Information 46SW A 05 P E T 1 G F Process onnection* A= 1/4"-18 Male NPT B= 1/8"-27 Male NPT = 1/4"BSPP W= F250 Female Autoclave System Insert 2 digit code (chart 1) Unit P= PSI Switch onfigurations E= SPDT [Form ] Electrical onnection T= 2ft. 18 AWG wires U= 4ft. 18 AWG wires W= 2 Meter 18 AWG wires Wetted Material** 0=17-4PH 1=316 L 2= Inconel 718 Reference 0= Sealed Gauge G= Vented Gauge Switching Point : Insert 5 digit code (chart 2) [5-95% of system line pressure] Switching Direction F= Falling R= Rising Hystersis: Insert 2 digit code (example: 1% is 01) [1% of line pressure minimum] Options No Options= 000 *For optional pressure ports and electrical interfaces please consult factory. 1/8 NPT Male not available under 50PSI or with 316L. F250 Female Autoclave is the only option for pressure ranges greater than 10,000. **316L available up to 10,000 PSI. For Inconel 718 consult factory on availability. hart 1 System ode , , , hart 2 Switching ode , , , , For pressures not shown, please consult factory. Dimensional Data 1 Amp Output SUPPLY SUPPLY - RED BLAK N/O N/ WHITE BLUE 1A Max, Resettable Fuse Protected GREEN Warranty Workmanship - AST, Inc. pressure transmitters have a limited one-year warranty to the original purchaser. AST, Inc. will replace or repair, free of charge, any defective transmitter. This warranty does not apply to any units that have been modified; misused, neglected or installed where the application exceeds published ratings. AST s sensors are made with pride in New Jersey, USA. If in the area please feel free to stop by for a visit! Installation/Applications - The purchaser is responsible for media compatibility, functional adequacy, and correct installation of the transmitter American Sensor Technologies Inc. AST46SW 12/18/12. All specifications subject to change without notice.
11 AST4600 Factory Sealed Gauge Transducer Explosionproof SA Approved For Hazardous Locations Overview AST4600 Explosionproof Transducer/Transmitter is SA approved for use in hazardous areas including: SA 30 (UL1203/FM3615) lass 1 Zone 1 Group II SA 30 lass 1 Div 1 Groups A, B,, D Explosionproof SA 30 lass 2 Div 1 Groups E, F, G Dust Ignition-proof onstructed with a simple-yet-rugged design, the factory-sealed AST4600 stands up to a variety of Explosionproof applications where price and performance are critical. NOW APPROVED SINGLE SEAL ANSI / ISA Benefits ANSI/ISA ertified Single Seal (no secondary seal required) ABS (American Bureau of Shipping) Approved All Stainless Steel onstruction No Oil-filled cavities, Welds, or Internal O-rings Wide Operating Temperature s from 100 to 20,000 PSI (Factory Sealed Gauge)* Low Static and Thermal Errors Rugged Design Withstands Harsh Environments Suitable for High Shock and Vibration Applications Available in Exotic Alloys (onsult Factory for Inconel 718 or Hastelloy 276) Applications Industrial OEM & Hydrogen Equipment Natural Gas ompressors Refrigeration Pipe Line Instrumentation Marine & Offshore 25 (77 F) Accuracy** Stability (1 year) Over Range Protection Burst ycles <±0.25% BFSL (<±0.5% BFSL for 7,500 to 20,000 PSI) ±0.25% FS, typical 2X Rated 5X Rated or 50,000 whichever is less >100 Million ** Accuracy includes non-linearity, hysteresis & non-repeatability Instrumentation Oil Platforms Well Head Power Generation Mining Applications * For pressures less than 100 PSI, see AST4600 Vented Gauge data sheet. US Environmental Data A P P R O V E D Krystal Bond P R O D U Technology by AST Temperature Operating Ambient -40 to 85 (-40 to 185 F) Operating Media -55 to 125 (-65 to 250 F) Storage -55 to 105 (-67 to 221 F) Thermal Limits ompensated Range 0 to 55 (30 to 130 F) T Zero: <±1.5% of FS T Span: <±1.5% of FS Other Shock EN Vibration EN , , and IE EMI/RFI Protection: Yes Rating: IP-66 T Electrical Data Output 4-20mA 1-5VD, 1-6VD Excitation 10-28VD 10-28VD Output Impedance >10k Ohms <100 Ohms, Nominal urrent onsumption: 25mA, typical 5mA, typical Bandwidth (-3dB): D to 1kHz (-3dB): D to 1kHz Output Noise: - <2mV RMS Zero Offset: <±1% of FS <±1% of FS Span Tolerance: <±2% of FS <±1.5% of FS Output Load: Ohms@10-28VD 5k Ohms, Min. Reverse Polarity Protection Yes Yes American Sensor Technologies 450 lark Dr., Mt. Olive, NJ phone (973) fax (973) info@astsensors.com
12 Ordering Information AST4600 W P 4 T Ranges Process onnection (for other ports contact factory) A= 1/4 NPT Male* I= 1/4 NPT Female* P= 1/2 NPT Male* W= F250 Female Autoclave (>10,000 PSI) Range Insert 5 digit pressure code from chart Unit B= BAR K=kg/cm2 P=PSI Outputs 3= 1-5V (3 Wire ase onnection) 4= 4-20mA (Loop Powered ase onnection) 6= 1-6V (3 Wire ase onnection) in PSIS ode , , , , , , , , , For gauge pressure units, see AST4600 Vented Gauge data sheet. T= 2ft. 18 AWG wires U= 4ft. 18 AWG wires W= 2 Meter 18 AWG wires Wetted Material 0= 17-4PH 2= Inconel 718** 1= 316 L* 4= Hastelloy 276** *Available up to 10,000 PSI, **onsult factory on availability Dimensional Data Output Red Black White Green For U.S. installations, sensor case ground Voltage V Supply -V Supply Output ase Ground (green wire) must be bonded to ground 4-20mA V Supply -V Supply Not Used ase Ground according to Article 501 & 505 of the NE. Warranty Workmanship - AST, Inc. pressure transmitters have a limited one-year warranty to the original purchaser. AST, Inc. will replace or repair, free of charge, any defective transmitter. This warranty does not apply to any units that have been modified; misused, neglected or installed where the application exceeds published ratings. AST s sensors are made with pride in New Jersey, USA. If in the area please feel free to stop by for a visit! Installation/Applications - The purchaser is responsible for media compatibility, functional adequacy, and correct installation of the transmitter American Sensor Technologies Inc. AST4600-Sealed 12/18/12. All specifications subject to change without notice.
13 AST4600 Vented Gauge Transducer Explosionproof SA Approved For Hazardous Locations Overview AST4600 Explosionproof Transducer/Transmitter is SA approved for use in hazardous areas including: SA 30 (UL1203/FM3615) lass 1 Zone 1 Group II SA 30 lass 1 Div 1 Groups A, B,, D Explosionproof onstructed with a simple-yet-rugged design, the AST4600 stands up to a variety of Explosionproof applications where price and performance are critical. NOW APPROVED SINGLE SEAL ANSI / ISA Benefits ANSI/ISA ertified Single Seal (no secondary seal required) ABS (American Bureau of Shipping) Approved All Stainless Steel onstruction Wide Operating Temperature s from 1 to 1,000 PSI Gauge* Low Static and Thermal Errors Rugged Design Withstands Harsh Environments Suitable for High Shock and Vibration Applications Available in Exotic Alloys (onsult Factory for Inconel 718 or Hastelloy 276) Applications Industrial OEM & Hydrogen Equipment Natural Gas ompressors Refrigeration Pipe Line Instrumentation Marine & Offshore 25 (77 F) Accuracy** Stability (1 year) Over Range Protection Burst ycles <±0.25% BFSL ±0.25% FS, typical 2X Rated 5X Rated >100 Million ** Accuracy includes non-linearity, hysteresis & non-repeatability Instrumentation Oil Platforms Well Head Power Generation Energy & Water Management * For pressures over 1,000 PSI, see AST4600 Factory Sealed Gauge data sheet. US Environmental Data A P P R O V E D Krystal Bond P R O D U Technology by AST Temperature Operating Ambient -40 to 85 (-40 to 185 F) Operating Media -55 to 125 (-65 to 250 F) Storage -55 to 105 (-67 to 221 F) Thermal Limits ompensated Range 0 to 55 (30 to 130 F) T Zero: <±1.5% of FS T Span: <±1.5% of FS Other Shock EN Vibration EN , , and IE EMI/RFI Protection: Yes Rating: IP-65 T Electrical Data Output 4-20mA 1-5VD, 1-6VD Excitation 10-28VD 10-28VD Output Impedance >10k Ohms <100 Ohms, Nominal urrent onsumption: 25mA, typical 5mA, typical Bandwidth (-3dB): D to 1kHz (-3dB): D to 1kHz Output Noise: - <2mV RMS Zero Offset: <±1% of FS <±1% of FS Span Tolerance: <±2% of FS <±1.5% of FS Output Load: Ohms@10-28VD 5k Ohms, Min. Reverse Polarity Protection Yes Yes American Sensor Technologies 450 lark Dr., Mt. Olive, NJ phone (973) fax (973) info@astsensors.com
14 Ordering Information AST4600 A G 0500 P 3 T Process onnection (for other ports contact factory) A= 1/4 NPT Male I= 1/4 NPT Female P= 1/2 NPT Male Reference G= Gauge V= Gauge (Vacuum alibrated) Range (Vented Gauge) Insert 4 digit pressure code from chart Unit B= Bar H= Inches H 2 O K= kg/cm2 P= PSI Outputs 3= 1-5V (3 Wire ase onnection) 4= 4-20mA (Loop Powered ase onnection) 6= 1-6V (3 Wire ase onnection) T= 2ft. 18 AWG wires U= 4ft. 18 AWG wires W= 2 Meter 18 AWG wires Ranges in PSIG ode , For sealed pressure units, see AST4600 Factory Sealed Gauge data sheet. 2.5 and 7.5 PSI sensor must be ordered in inches of H 2 O. Wetted Material 0= 17-4PH 2= Inconel 718* 1= 316 L 4= Hastelloy 276* *onsult factory on availability Dimensional Data Output Red Black White Green For U.S. installations, sensor case ground Voltage V Supply -V Supply Output ase Ground (green wire) must be bonded to ground 4-20mA V Supply -V Supply Not Used ase Ground according to Article 501 & 505 of the NE. Warranty Workmanship - AST, Inc. pressure transmitters have a limited one-year warranty to the original purchaser. AST, Inc. will replace or repair, free of charge, any defective transmitter. This warranty does not apply to any units that have been modified; misused, neglected or installed where the application exceeds published ratings. AST s sensors are made with pride in New Jersey, USA. If in the area please feel free to stop by for a visit! Installation/Applications - The purchaser is responsible for media compatibility, functional adequacy, and correct installation of the transmitter American Sensor Technologies Inc. AST4600-Vented 12/18/12. All specifications subject to change without notice.
15 Differential Transducer AST5300 AST53ED AST53EN ISO9001:2008 The AST5300 offers low DP ranges in high line pressure with excellent burst pressure capabilities. The DP has no oil filled cavities and no internal o-rings to fail; making it ideal for food and beverage, oil & gas, pharmaceuticals, semiconductor industries and cold ambients. Benefits Oil free - no containment issues Wide operating media temperature Wide range of media compatibility ompact size Explosion Proof Rated SA30 lass I Zone 1 Group II lass I Division 1 Groups A, B,, D lass II, Division 1, Groups E, F and G lass III Division 1 Non-Incendive Rated Applications Flow measurement - liquids and gases High Purity Gases Tank level monitoring Ballast measurement Filtration ryogenics SA213 lass I Division 2 Groups A, B,, D ANSI/ISA Single Seal Device Environmental Data Temperature 25 (77 F) [% of FS] Line 1,500 PSI Operating -40 to 85 (-40 to 185 F) Burst 5,000 PSI Storage Media ompensated Range T Zero T Span -55 to 120 (-67 to 248 F) -55 to 125 (-67 to 257 F) -5 to 65 (23 to 149 F) <± 0.5% (-5 to 65 ) of FS <± 0.5% (-5 to 65 ) of FS Linearity <± 0.2% Stability <± 0.5% Zero Offset (10 to 30 ) <± 1.0% Zero Offset (-40 to 85 ) <± 3.0% Span Tolerance <± 0.2% Electrical Data Output 0-5V, 1-5 Three Wire 4-20mA V Ratiometric Excitation 10-28VD 10-28VD 5VD, reg urrent onsumption: 5mA, typ - 5mA, typ Output Load: 10k Ohms Ohms 10k Ohms Reverse Polarity Protection Yes Yes Yes American Sensor Technologies 450 lark Dr., Mt. Olive, NJ phone (973) fax (973) info@astsensors.com
16 Ordering Information AST53 00 DP 0010 P 4 M Approval 00= OEM ED= Explosion proof EN= Non-Incendive Electrical onnection Table 00 ED EN I DIN A * * M onduit, 4ft. * * N onduit, 6ft. * * Mounting / onnection DP= Threaded Fittings (1/4 FNPT) R 6-Pin Bendix PT06 * T onduit, 18AWG, 24 in * U onduit, 18AWG, 48 in * Differential 0010= 10 PSI Unit P= PSI Output 1= V ratiometric 2= 0-5V (3-wire) 3= 1-5V 4= 4-20mA Electrical onnection (see table) Subject to Approval Type Selected Wetted Material 8= 316L & Inconel x750 Options 00= No Special Options W onduit, 18AWG, 2m * Y Turck M12 4-Pin Eurofast * The line pressure specification is the maximum pressure the AST5300 can see without damage. Any pressure applied over the listed number will likely damage the transducer and will, at minimum, cause a permanent zero shift. Line pressure should be applied evenly to both ports during start up and shut down. A Line pressure of 500 psi or less can be applied to one pressure port with the other port at 0psi and will not cause a zero shift of the output. above 500 PSI to one side may cause a temporary zero shift. To recover from a zero shift caused by negative over-pressure to L (low / downstream process connection) within the listed limits, apply a positive over-pressure H (high / upstream process connection) to 1,450 PSI for a duration of five minutes. Remove the over-pressure and check the zero with no pressure applied. If the zero has not recovered, repeat the positive over-pressure and recheck zero. If it has not recovered after the second try, the zero has been permanently shifted. ontact the factory. Dimensional Data Process onnections DP = 1/4 FNPT H = high / upstream pressure L = low / downstream pressure For warranty information, please visit: American Sensor Technologies Inc. AST5300 1/8/13 All specifications subject to change without notice.
0-5V, 1-5V, 1-6V 0-10V, 1-10V V
AST20HA Industrial Precision Transducer / Transmitter Overview The AST20HA is a digitally compensated pressure transducer / pressure transmitter that offers high performance over temperature. Krystal Bond
More informationAST44LP Intrinsically Safe Low Pressure Transducers / Transmitters
AST44LP Intrinsically Safe Low Transducers / Transmitters Class I Division 1 Groups C, D IS with Approved Barrier OVERVIEW The AST44LP is a stainless steel pressure transducer with a wide variety of options.
More informationSelectable ranges and an LCD are a technician s best friend, that s why we make them standard on every dry media differential pressure sensor!
PRESSURE SENSORS PRESSURE PDP3 Series 0-2 32 PDP3 Series 0-10, 0-25 34 PG Gauge Series 36 PW Wet-Wet Series (Cable Version) 38 PW Wet-Wet Series (Conduit Version) 40 PW Series Ordering Guidance 42 Selectable
More informationTransducers Direct, LLC Overview
2010 PRODUCT CATALOG Please use PDF Bookmarks to navigate this catalog Contents: Company Overview Transducers Direct Web Page (Must be connected to the Internet). Catalog Pressure Transducers Linear and
More informationEQUIVALENT BASIC CIRCUIT
FEATURES Reliable semiconductor technology Calibrated and temperature compensated Rugged, stainless steel package NEMA 4 design Small size Absolute, gage, sealed gage, vacuum gage pressures 0 psi to 3
More informationSSI Technologies MediaSensor
SSI Technologies MediaSensor P51 Pressure Transducers Product Description SSI s line of bulk micro-machined, absolute and gage pressure transducers and transmitters for both harsh and benign media with
More informationSSI Technologies Application Note PS-AN2 MediaSensor Absolute & Gage Pressure Transducers & Transmitters Product Overview
Product Description The MediaSensor (P51) family of bulk micro-machined, absolute, gage and sealed pressure transducers and transmitters are for both harsh and benign media with the superior typical accuracy
More informationPressure Transmitter. Pressure transmitter with compact design Model EDC-K. Electronic. Applications. Special Features.
Pressure transmitter with compact design Electronic Pressure Transmitter Applications Mechanical engineering Machine tools Control and feedback control systems Hydraulics / Pneumatics Pumps/ Compressors
More informationBy Karmjit Sidhu, VP, Business Development American Sensor Technologies
New Differential Pressure Sensor Incorporates LVDT Technology to Create More Environmentally-Resistant, Dependable and Economical Pressure Sensing Solution By Karmjit Sidhu, VP, Business Development American
More informationU5200 Industrial Pressure Transducer
FEATURES Heavy Industrial E Approval 10 V/m EMI Protection Reverse Polarity Protection on Input Short ircuit Protection on Output Up to ±0.1% Accuracy Up to ±0.75% Total Error Band ompact Outline -40 to
More informationPressure transmitters for heavy-duty applications MBS 2000 and MBS 2050
Data sheet Pressure transmitters for heavy-duty applications MBS 2000 and MBS 2050 The compact heavy duty pressure transmitters MBS 2000 and MBS 2050 are designed for use in hydraulic applications. MBS
More informationDMP 333. Industrial Pressure Transmitter For High Pressure. Stainless Steel Sensor
DMP Industrial Pressure Transmitter For High Pressure Stainless Steel Sensor accuracy according to IEC 60770: standard: 0.5 % FSO option: 0.5 / 0. % FSO Nominal pressure from 0... 00 bar up to 0... 600
More informationPressure transmitters for heavy duty applications MBS 8200 and MBS 8250
Data sheet Pressure transmitters for heavy duty applications MBS 8200 and MBS 8250 MBS 8200 is a series of compact pressure transmitters developed to withstand the pressure pulsations and vibrations known
More informationMid-West Instrument. Series 700 "Wet/Wet" Installation and Operating Instructions. Differential Pressure Transmitter
Mid-West Instrument IM_700/A Series 700 "Wet/Wet" Installation and Operating Instructions Differential Pressure Transmitter 6500 Dobry Dr. Sterling Heights, MI USA Toll Free: 800-648-5778 Ph 586-254-6500
More informationHigh temperature pressure transmitters for heavy-duty applications MBS 2200 and MBS 2250
Data sheet High temperature pressure transmitters for heavy-duty applications MBS 2200 and MBS 2250 The compact heavy duty pressure transmitter type MBS 2200 and MBS 2250 are designed for use in severe
More informationPressure transmitter for industrial applications Type MBS 4510
MAKING MODERN LIVING POSSIBLE Data sheet Pressure transmitter for industrial applications Type MBS 4510 The high accuracy flush diaphragm pressure transmitter MBS 4510 is designed for use in non-uniform,
More informationPressure transmitter for marine applications MBS 33M
Data sheet Pressure transmitter for marine applications MBS 33M The standard pressure transmitter MBS 33M is designed for use in almost all marine applications, and offers a reliable pressure measurement,
More informationPressure transmitter for general industrial purposes MBS 3000 and MBS 3050
Data sheet Pressure transmitter for general industrial purposes MBS 3000 and MBS 3050 The compact pressure transmitter, type MBS 3000, is designed for use in almost all industrial applications, and offers
More informationUltra High Purity Transducer, Ex na nl Models WU-20, WU-25 and WU-26
Electronic Pressure Measurement Ultra High Purity Transducer, Ex na nl Models WU-20, WU-25 and WU-26 WIKA Datasheet WU-2X Applications Gas panels for OEM tools Semiconductor, flat panel display and photovoltaic
More informationPressure transmitter for general industrial purposes Type MBS 3000 and MBS 3050
MAKING MODERN LIVING POSSIBLE Data sheet Pressure transmitter for general industrial purposes Type MBS 3000 and MBS 3050 The compact pressure transmitter, type MBS 3000, is designed for use in almost all
More informationPiezoresistive Pressure Sensors
Pressure Piezoresistive Pressure Sensors for utomotive R&, Test pplications Type 4260 4262 versatile high performance pressure sensor that will operate in harsh test environments where temperature extremes,
More informationPRESSURE BENCH OPERATING INSTRUCTIONS
PRESSURE BENCH OPERATING INSTRUCTIONS Overview: The pressure bench system allows the user to apply a variety of calibrated pressures to a variety of high and low pressure transducers. In addition the system
More informationType A-10 General Purpose Pressure Transmitters
Type A-10 General Purpose Pressure Transmitters Applications Mechanical engineering Machine tools Process control and automation Hydraulics and pneumatics Pumps and compressors Special Features Pressure
More informationPressure transmitters for heavy duty applications MBS 3200 and 3250
Data sheet Pressure transmitters for heavy duty applications MBS 3200 and 3250 The compact high temperature pressure transmitter MBS 3200 is designed for use in hydraulic and almost all industrial applications,
More informationType E-10, E-11 Hazardous Area Explosion-proof Transmitters
Electronic Pressure Catalog > Hazardous Area > E-10, E-11 Type E-10, E-11 Hazardous Area Explosion-proof Transmitters Meets ANSI / ISA 12.27.01-2003 single seal requirements - no dual seal required Applications
More informationOEM Pressure Transmitters for heavy-duty applications Type MBS 1200 and MBS 1250
Data sheet OEM Pressure Transmitters for heavy-duty applications Type MBS 100 and MBS 150 The compact OEM pressure transmitter programme is designed for use in severe hydraulic applications. The programme
More informationU.S. GAUGE PMT PRODUCTS 820 PENNSYLVANIA BLVD., FEASTERVILLE, PENNSYLVANIA U.S.A. TEL: (215) FAX: (215)
U.S. GAUGE PMT PRODUCTS 820 PENNSYLVANIA BLVD., FEASTERVILLE, PENNSYLVANIA 19053 U.S.A. TEL: (215) 355-6900 FAX: (215) 354-1801 www.ametekusg.com 2009, by AMETEK, Inc. All rights reserved. Printed in the
More informationPressure transmitter for marine applications MBS 3100 and MBS 3150
Data sheet Pressure transmitter for marine applications MBS 3100 and MBS 3150 The compact ship approved pressure transmitters MBS 3100 and MBS 3150 are designed for use in almost all marine applications.
More informationSolid State Electronic Pressure Switch with Integral LED Display Model PSD-10
Solid State Electronic Pressure Switch with Integral LED Display Model PSD-10 Electronic Pressure Measurement WIKA Datasheet PSD-10 Applications Hydraulics and pneumatics Filter monitoring Pump control
More informationM5200 Industrial Pressure Transducer
SPECIFICATIONS Wide Temperature Range Compact Variety of Pressure Ports and Electrical Configurations Optional Stainless Steel Snubber CE Compliant and Weatherproof Gage, Sealed, Compound The pressure
More informationOEM Pressure Transmitters
OEM Pressure Transmitters Type ECO-1 Applications Hydraulics and pneumatics Mechanical engineering General industrial applications Special Features Pressure ranges from 0-15psi to 0...15,000psi 4-20 ma
More informationOEM Pressure transmitter for industrial applications Type MBS Technical brochure
OEM Pressure transmitter for industrial applications Type MBS 1200 Technical brochure Features Designed for use in severe industrial OEM applications For medium and ambient temperatures up to 125ºC All
More informationMBS 1200 and MBS 1250
Data sheet OEM Pressure Transmitters for heavy-duty applications MBS 1200 and MBS 1250 The compact OEM pressure transmitter programme is designed for use in severe hydraulic applications. The programme
More informationPiezoresistive pressure transmitters
Pressure Piezoresistive pressure transmitters for Test & Measurement applications Type 4260... 4262... versatile high performance pressure transmitter that will operate in harsh test environments where
More informationLevel instruments. Continuous level measurement - Capacitance transmitters SITRANS LC300. 5/262 Siemens FI Overview.
Overview Configuration is an inverse frequency shift capacitance continuous It is ideal for standard industrial applications in chemical, hydrocarbon processing, food and beverage and mining, aggregate
More informationDMP 331P DMP 331P. Industrial Pressure Transmitter. Pressure Ports And Process Connections With Flush Welded Stainless Steel Diaphragm
DMP P Industrial Pressure Transmitter Pressure Ports And Process Connections With Flush Welded Stainless Steel Diaphragm accuracy according to IEC 60770: standard: 0.5 % FSO option: 0.5 % FSO Industrial
More informationJUMO MIDAS S05 Pressure transmitter Type
Data Sheet 40.00 Page /8 JUMO MIDAS S05 Pressure transmitter Type 4000 Brief description The JUMO MIDAS S05 pressure transmitter is available with both relative pressure and absolute pressure measurement
More informationPRESSURE TRANSDUCERS. Specifications. Individual Specifications
00 Series and 00 Heavy Duty Series Compact OEM Pressure Transmitters 0 50 psi to 0-0,000 psi ranges (0-.5 bar to 0-,00 bar) High Proof Pressures Broad Choice of Outputs RoHS Compliant For OEMs that need
More informationPressure transmitter for industrial applications Type MBS 4500
MAKING MODERN LIVING POSSIBLE Data sheet Pressure transmitter for industrial applications Type MBS 4500 The high accuracy pressure transmitter MBS 4500 is designed for use in almost all industrial applications,
More informationBTE2000 / PTE2000 Series Precision stainless steel pressure transmitters
FEATURES...5 to...5 bar,...5 to...5 psi gage 1 For corrosive media in harsh environments 1...6 or... ma output Field interchangeable All welded stainless steel diaphragm construction MEDIA COMPATIBILITY
More informationDMP 331. Industrial Pressure Transmitter for Low Pressure. Stainless Steel Sensor
DMP Industrial Pressure Transmitter for Low Pressure Stainless Steel Sensor accuracy according to IEC 60770: standard: 0.5 % FSO option: 0.5 / 0. % FSO Nominal pressure from 0... 00 mbar up to 0... 40
More informationDMK 331P. Industrial Pressure Transmitter. Pressure Ports With Flush Welded Stainless Steel Diaphragm. accuracy according to IEC 60770: 0.
DMK P Industrial Pressure Transmitter Pressure Ports With Flush Welded Stainless Steel Diaphragm accuracy according to IEC 60770: 0.5 % FSO Nominal pressure from 0... 60 bar up to 0... 400 bar Output signals
More informationDMK 331P. Industrial Pressure Transmitter. Pressure Ports With Flush Welded Stainless Steel Diaphragm
Industrial Pressure Transmitter Pressure Ports With Flush Welded Stainless Steel Diaphragm accuracy according to IEC 60770: 0.5 % FSO Nominal pressure from 0... 60 bar up to 0... 400 bar Output signals
More informationDMP 331 DMP 331. Industrial Pressure Transmitter for Low Pressure. Stainless Steel Sensor. Pressure Transmitter. Industrial
TEMATEC GmbH Postal address: House address Fon (+49) 0 4-870-0 Postbox 6 Löhestr. 7 Fax (+49) 0 4-870-0 http: // www.tematec.de 5759 Hennef 577 Hennef e-mail: team@tematec.de TEMATEC GmbH Data Sheet DMP
More informationPressure transmitters for industrial applications Type MBS 4510
Pressure transmitters for industrial applications Type MBS 4510 Technical brochure Features Designed for use in severe industrial environments Enslosure and wetted parts of acid-resistant stainless steel
More informationType A-10 General Purpose Pressure Transmitter
General Purpose TRONIC > General Purpose > A-10 Type A-10 General Purpose Pressure Transmitter Standard Features Signal output: 4-20 ma 2-wire or 0-10 V 3-wire Supply voltage: 8-30 DC (14-30 VDC) Process
More informationPressure transmitter for general purpose Type MBS 1700 and MBS 1750
MAKING MODERN LIVING POSSIBLE Data sheet Pressure transmitter for general purpose Type MBS 1700 and MBS 1750 The compact pressure transmitters MBS 1700 and MBS 1750 are designed for use as a general purpose
More informationPX409 Series. mv/v, 0 to 5 or 0 to 10 Vdc, or 4 to 20 ma Outputs Uni-Directional Ranges 0-10 inh2o to psid
Micro-Machined Silicon Transducers wet/dry differential mv/v, 0 to 5 or 0 to 10 Vdc, or 4 to 20 ma Outputs Uni-Directional Ranges 0-10 inh2o to 0-1000 psid PX409 Series Standard U 5-Point NIST Traceable
More informationDMP 331P. Industrial Pressure Transmitter. Pressure Ports And Process Connections With Flush Welded Stainless Steel Diaphragm
DMP P Industrial Pressure Transmitter Pressure Ports And Process Connections With Flush Welded Stainless Steel accuracy according to IEC 60770: standard: 0.5 % FSO option: 0.5 % FSO from 0... 00 mbar up
More informationABB Instrumentation. 50T Series Transmitters Model 54G/A gauge/absolute pressure transmitter for sanitary use. Specification sheet
Specification sheet 50T Series Transmitters Model 54G/A gauge/absolute pressure transmitter for sanitary use Ranges : - 100 to 4000 kpa - 1 to 40 bar - 14.5 to 600 psi Base accuracy : 0.2%(BFSL) Piezoresistive
More informationDMK 331P DMK 331P. Industrial Pressure Transmitter. Pressure Ports With Flush Welded Stainless Steel Diaphragm. Pressure Transmitter.
TEMATEC GmbH Postal address:: Postbox 6 House address Löhestr. 7 5759 Hennef 577 Hennef Fon (+49) 0 4-87 0-0 Fax (+49) 0 4-87 0-0 http: // www.tematec.de e-mail: team@ tematec.de TEMATEC GmbH Data Sheet
More informationSSI Technologies Application Note PS-AN7 MediaGauge (Model MG-MD) Digital Pressure Gauge Product Overview
Product Description The MediaGauge MG-MD is a multi-functional digital pressure gauge consisting of a media isolated piezoresistive pressure sensing element, signal conditioning circuitry for temperature
More informationMid-West Instrument. Piston Type Model 220. Hazardous Locations. Indicating / Non-Indicating Differential Pressure Switch or Transmitter
BULLETIN NO. 220/11 (SUPERSEDES BULLETIN NO. 220/06) Mid-West Instrument Piston Type Model 220 Hazardous Locations Indicating / Non-Indicating Differential Pressure Switch or Transmitter Low cost piston
More informationPressure Sensor - EPT3100
Pressure Sensor - EPT3100 Up to 4000 Bar pressure range High strength, rugged stainless steel design Competitively priced The EPT3100 is a high quality all stainless steel pressure transducer, intended
More informationG 1/4 A DIN 3852 (bar version) ±0.5 %FS max
Pressure Transducers HDA 00 & 700 About HDA 00 & 700 Pressure Transducers: Series HDA 000 transducers are compact, heavy-duty, pressure instruments designed for both OEM industrial and off-road applications
More informationMicro-Machined Silicon Transducers
Micro-Machined Silicon Transducers wet/wet differential Pressure Models mv/v, 0 to 5 or 0 to 10 Vdc, or 4 to 20 ma Outputs Uni-Directional Ranges 0-10 inh2o to 0-1000 psid PX409 Series Standard U Precision
More informationPressure transmitter for marine applications Type MBS 5100 and MBS 5150
Data sheet Pressure transmitter for marine applications Type MBS 5100 and MBS 5150 The ship approved high accuracy block pressure transmitter is designed for use in almost all marine applications. MBS
More informationPRESSURE TRANSDUCERS. Specifications. Individual Specifications
GEMS COMPLIANT 00 Series and 00 Heavy Duty Series Compact OEM Pressure Transmitters 0 00 psi to 0-0,000 psi ranges (0- bar to 0-,00 bar) High Proof Pressures Broad Choice of Outputs RoHS Compliant For
More informationPressure measurement PP20H Fully welded hygienic pressure sensor with flush membrane
Product highlights All market typical hygienic connections available EHEDG & 3-A certified versions available Condensate-proof measuring cell IO-Link available Space-saving installations from DN 25 on
More informationP255 Stainless Steel Pressure Transducer
P255 Stainless Steel Pressure Transducer Description The model P255 is based on Kavlico s fieldproven ceramic capacitive technology with the latest state-of-the-art ASIC. Featuring a 316SS housing, the
More informationOEM Pressure Transmitters
OEM Pressure Transmitters Type MH-2 Applications Mobile hydraulic systems Automotive industry Compressor systems Special Features Pressure ranges from 1000 psi to 8000 psi 4-20 ma, 1-5V, 0-10V, 0.5-4.5V
More informationDL 01. Battery Powered Precision Digital Gauge for Leak Testing. Stainless Steel Sensor. class 0.05
DL 0 Battery Powered for Leak Testing Stainless Steel Sensor class 0.05 Nominal pressure from 0 00 mbar up to 0... 00 bar Special characteristics modular sensor concept data logger graphic display stainless
More informationCTE7000 / CTU7000 Series Miniature pressure transmitters
FEATURES 10 mbar to bar, 0.1 to 7 psi gage 1 pressure 0..., 0...10, 0...4., 1...6 or 4...20 ma output Field interchangeable Rugged stainless steel housing EMC according to EN 61326-1 9 MEDIA COMPATIBILITY
More informationRelative pressure transmitter type 550 for mobile hydraulic
Relative pressure transmitter type 550 for mobile hydraulic Pressure range 0... 40 600 bar The pressure transmitter type 550 meets the highest requirements for mobile hydraulic applications. This sensor
More informationCTE9000 / CTU9000 Series OEM pressure transmitters for industrial media
FEATURES mbar to 35 bar, 15 to 500 psi gage 1 or absolute 10 pressure 05, 010, 0545, 16 or 420 ma output Field interchangeable All welded stainless steel diaphragm construction EMC according to EN 61326-1
More informationUltra High Purity Transducer, Ex na ic Models WUC-10, WUC-15 and WUC-16
Electronic Pressure Measurement Ultra High Purity Transducer, Ex na ic Models WUC-10, WUC-15 and WUC-16 WIKA Datasheet WUC-1X Applications Semiconductor, flat panel display and photovoltaic industry Specialty
More informationData Sheet P265 Stainless Steel Pressure Transducer
Data Sheet P265 Stainless Steel Pressure Transducer Main Features Pressure Ranges Electrical Connection 0 to 15 up to 0 to 1000 PSI Packard Electric Metri-Pack 150 Series, 12 20 AWG leads Pressure Connection
More informationFigure 1: WPR2 Dimensions and Hardware
Installation and Operation Instructions WPR2 Series (Max. Line Pressure < 300 PSI) Wet to Wet Differential Pressure Ø0.200" 2.60" 4.47" 5.47" 5.28" 3.00" Precautions Figure 1: WPR2 Dimensions and Hardware
More informationDCT 533. Industrial Pressure Transmitter with IO-Link Interface. Stainless Steel Sensor
DCT 5 Industrial Pressure Transmitter with IO-Link Interface Stainless Steel Sensor accuracy according to IEC 60770: standart: ± 0.5 % FSO sption: ± 0.5 % FSO Nominal pressure from 0... 00 mbar up to 0...
More informationG2 Industrial Grade Meters
G2 Industrial Grade Meters The unique modular approach of the Industrial Grade Meter line allows you to section 2: g2 industrial grade meters design a meter to match your specific application. Turbine
More informationMid-West Instrument. Diaphragm Type Model 240. Hazardous Locations. Indicating / Non-Indicating Differential Pressure Switch or Transmitter
BULLETIN NO. 240/11 (SUPERSEDES BULLETIN NO. 240/06) Mid-West Instrument Diaphragm Type Model 240 Hazardous Locations Indicating / Non-Indicating Differential Pressure Switch or Transmitter Field wireable
More informationIntrinsically safe presure transmitters for hazardous environments Type MBS 4201, MBS 4251, MBS 4701 and MBS Technical brochure
Intrinsically safe presure transmitters for hazardous environments Type MBS 4201, MBS 4251, MBS 4701 and MBS 4751 Technical brochure Features Ex ll 1G EEx ia llc T4 - T6 in compliance with ATEX 100a Applicable
More informationMid-West Instrument. Piston Type Differential Pressure Gauges Switches & Transmitters Model 123
BULLETIN NO. 123/11 (SUPERSEDES BULLETIN NO. 123/03) Piston Type Differential Pressure Gauges Switches & Transmitters A low cost differential pressure gauge for use in measuring the pressure drop across
More informationMiniature Solenoid Valves
Miniature Solenoid Valves Our IPS Miniature Solenoid Valves offer precision performance under extreme conditions. Offered as 2-Way and 3-Way Valves with four internal body configurations and five seat
More informationElectronic Pressure Switches
96 Pressure Switches Electronic Pressure Switches Electronic E.5 switching output Electronic pressure switches, High-Performance series with one switching output Outstanding overpressure protection (up
More informationPressure transmitters for heavy duty applications Type MBS 3250
Pressure transmitters for heavy duty applications Type MBS 3250 Features Designed for use in harsh industrial environments For medium and ambient temperatures up to 125 C With integrated pulse-snubber.
More informationIndustrial Pressure Transmitters
Industrial Pressure Transmitters Type S-10, S-11 Applications Hydraulics and pneumatics Test equipment Pump and compressor control Liquid level measurement Special Features Standard ranges available from
More informationData Sheet P4055 Pressure Transducer
Data Sheet P4055 Pressure Transducer Main Features Pressure Ranges Electrical Connection Pressure Connection Housing Material Output Signal 0 to 3 up to 0 to 300 PSI Packard Electric Metri-Pack 150 Series
More informationElectronic Pressure Switches
96 Pressure Switches Electronic Pressure Switches Electronic E.6 2 switching outputs Electronic pressure switches, High-Performance series with two switching outputs Outstanding overpressure protection
More informationSeal material. Pressure range. Pressure connection -40 F +212 F 1 -4 F +257 F 3
0675 / 0680 / 0690 Order matrix for pressure transmitters in Oil-Filled Housing ype Pressure range Pressure connection Seal material Electrical connection 0.5 4.5 V, ratiometric 0675 0 10 V, -wire 0680
More informationThermal hysteresis 0.5% max. of full scale (within compensated temperature range) 1% max. for ranges mbar mbar mbar
Pressure Transmitter Type FM40466 General application Pressure transmitters are used to measure the relative (gauge) and absolute pressures in liquids or gases. The measuring device for the transmitter
More informationAdjustment range. Seal material. Pressure connection
0520 Order matrix for electronic pressure switches.3 Type Adjustment range Pressure connection Seal material lectrical connection Type lectronic pressure switch 0520 Adjustment range 1) for NO 0 145 psi
More informationModel DCT Digitally Compensated Pressure Transducer
EPMP 1 Product ata ELECTRONIC PRESSURE MESUREMENT PROUCTS Model CT igitally Compensated ESCRIPTION The Model CT is designed for general industrial and commercial requirements offering excellent performance
More informationJUMO dtrans p20. Process pressure transmitter. Type Brief description. Key features. Block diagram
Data Sheet 403025 Page 1/10 JUMO dtrans p20 Process pressure transmitter Brief description The JUMO dtrans p20 pressure transmitter with HART interface combines maximum precision with easy operation. It
More informationMS4515 SPECIFICATIONS FEATURES APPLICATIONS
. SPECIFICATIONS PCB Mounted Pressure Transducers Pressure Ranges from 2 to 30 inches H 2O Amplified Ratiometric Analog Output Differential & Gage Temperature Compensated 3.3V or 5.0 V DC Supply Voltage
More informationSPT- I / U PRESSURE TRANSMITTER for general applications
Fields of application Design Examples Hydraulics Air conditioning and heating Testing technology Industrial robots Process controlling Water technology Pneumatics Description The pressure transmitters
More informationUltra High Purity Transducer, Ex na n Models WUC-10, WUC-15 and WUC-16
Electronic Pressure Measurement Ultra High Purity Transducer, Ex na n Models WUC-10, WUC-15 and WUC-16 WIKA Datasheet WUC-1X Applications Semiconductor, Flat Panel Display and Photovoltaic Industry Specialty
More informationCTE8000 / CTU8000 Series
CTE8000 / CTU8000 Series FEATURES 250 mbar to 100 bar, 5 to 1500 psi gage1 or absolute10 pressure 0...5 V, 0...10 V or 4...20 ma output Field interchangeable For many industrial gases and liquids EMC according
More informationData Sheet P255 Stainless Steel Pressure Transducer
Data Sheet P255 Stainless Steel Pressure Transducer Main Features Pressure Ranges Electrical Connection 0 to 15 up to 0 to 1000 PSI Packard Electric Metri-Pack 150 Series Pressure Connection 1/4-18 NPT
More informationMid-West Instrument. Piston Type Differential Pressure Gauges Switches & Transmitters Model 120
BULLETIN NO. 120/11 (SUPERSEDES BULLETIN NO. 120/02) Piston Type Differential Pressure Gauges Switches & Transmitters A low cost differential pressure gauge for use in measuring the pressure drop across
More informationPressure transmitter for air and water applications Type MBS 1900
Data sheet Pressure transmitter for air and water applications Type MBS 1900 The pressure transmitter MBS 1900 is designed for use in air and water applications like Booster Pumps and Air Compressors.
More informationUNIK Pressure Sensing Platform. GE Sensing & Inspection Technologies. Features
GE Sensing & Inspection Technologies UNIK 5000 Pressure Sensing Platform The UNIK 5000 is a high performance configurable solution to pressure measurement. The use of Druck silicon technology and analogue
More informationMid-West Instrument. Piston Type Differential Pressure Gauges Switches & Transmitters Model 124
BULLETIN NO. 124/12 (SUPERSEDES BULLETIN NO. 124/11) Mid-West Instrument Piston Type Differential Pressure Gauges Switches & Transmitters A low cost differential pressure gauge for use in measuring the
More informationElectronic Temperature Control & Bulb Well Assembly (AC)
Electronic Temperature ontrol & ulb Well ssembly () 0916 86816 This is a line voltage single-stage electronic temperature control with singlepole, double-throw relay output and LED indication. It is designed
More informationTEL-TRU PRESSURE TRANSMITTERS Threaded Series Model P121
Price List PTP17 Effective 3/10/17 P121 $330.75 C 12 mv/v (4wire) F 16 Vdc output 44.10 G 15 Vdc output 44.10 H 0100 mv output 44.10 L 111 Vdc output 44.10 M 110 Vdc output 44.10 3 0.25% Std. 6 0.10%,
More informationDM01. Battery Powered Precision Digital Gauge. Stainless Steel Sensor. class 0.05
Battery Powered Stainless Steel Sensor class 0.05 Nominal pressure from 0 00 mbar up to 0... 00 bar Special characteristics modular sensor concept data logger graphic display stainless steel housing Ø
More information* * Data sheet DA A (ATEX) Differential pressure measuring device for potentially explosive areas
09015062 DB_EN_DA10_ATEX Rev. ST4-A 03/18 *09015062* Data sheet DA10... 0A (ATEX) Differential pressure measuring device for potentially explosive areas Gas explosion protection Zone 1 and 2, gases and
More informationWhat is the secret to our success?
Australia s Quality Load Cell Manufacturer For over 20 years Delphi has been a reliable source of tension load measurement solutions... What is the secret to our success? TENSION CELLS Delphi Measurement
More informationFeatures/Benefits INSTALL IT & FORGET IT FEATURES & BENEFITS
Features/Benefits INSTALL IT & FORGET IT The ForceMeter TM offers the same rugged design for which the Niagara Meters brand is known. The ForceMeter is ideal for applications including water, compressed
More informationMS4525 SPECIFICATIONS
SPECIFICATIONS PCB Mounted Pressure Transducers Amplified Ratiometric Analog Output Differential, Gage, Absolute, Compound, & Vacuum Temperature Compensated 3.3 or 5.0 Vdc Supply Voltage The MS4525 is
More information