Transducers Direct, LLC Overview

Transcription

1 2010 PRODUCT CATALOG Please use PDF Bookmarks to navigate this catalog Contents: Company Overview Transducers Direct Web Page (Must be connected to the Internet). Catalog Pressure Transducers Linear and Rotary Position Transducers Linear Signal Conditioner Melt Pressure Transducers Pressure Switches Temperature Switches Encoders Flow Meters and Switches Liquid Level Switches Digital Meters

2 Transducers Direct, LLC Overview Transducers Direct is a privately held company based in the Cincinnati Ohio area that has 8 manufacturing sites mostly in North America. The company occupies a 30,000 sq ft building that is 8 years old and focuses on industrial applications. Rob Matthes has over 20 years experience with pressure, melt pressure, linear/rotary and magnetostrictive transducers for the Plastics Industry started it in Transducers Direct supplies a wide range of products to end users but primarily to key / large OEM s. Products manufactured under the Transducers Direct brand are: Hydraulic/Pneumatic Pressure Transducers, Pressure Switches, Melt Pressure Transducers, Linear and Rotary Transducers, Digital Displays, Flow meters and switches as weel as liquid level switches. These products are easily configuable to meet most industrial applications and have the ability for direct replacements of competitive units. The company is also a member of the Electronics Committee of SPI (Society of Plastics Industry).

3 The TD1000 Series Ultra High Resolution Digital Measurement, General Purpose, Pressure Transducer PRELIMINARY SERIES: TD1000 FEATURES Totally digital proprietary design Innovative redundent sensing elements 24V digital output for pressure or temp switch point Voltage and current outputs Custom pressure Ranges and outputs available More standard pressure ranges, Industry First Optional 4x or 10x over pressure (on most ranges) 0.25% and 0.1% accuracy available ASIC technology, no zero/span potentiometers All stainless steel welded housing IP-69K rated seal available (high pressure wash down) Innovative low current consumption, ideal for custom wireless solutions Programable systems available for OEM/systems integrators for in-house configuring of outputs, ranges and set points to reduce inventory and lead times Calibration Certificates available (contact customer service) DESCRIPTION The TD1000 Series digital/configurable (an industry first) industrial pressure transducer features stability and accuracy over a wide temperature range at lower cost than competitive units typically not found in older analog designs yet is plug and play with most lower grade competitive units. With its proprietary digital/asic technology, the TD1000 Series features field proven redundant sensing elements without the need for solder in resistors or trim pots that can drift over time. This provides years of excellent performance and reliability even in the harshest/demanding applications. This combined with optional 4x or 10x over pressure and the optional integrated temperature or pressure digital switch feature, makes the TD1000 Series truly an industry first and second to none. For extreme applications where power washers are used for wash down, the TD1000 Series optional IP69K seal, another industry first, makes it ideal no matter what the environment. With its flexible low power design and lower manufacturing costs, the TD1000 Series offers outstanding value and makes it ideal for custom wireless applications. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Direct web site, it is up to the customer to determine the suitability of the product in the application.

4 ELECTRICAL CONNECTIONS Voltage Units Current Units Pin 1 +Power Supply Pin 2 Pin 3 N/C Pin 4 N/C Digital (optional) 9.4 mini DIN NPT 2 1 MATING CONNECTOR/CABLE P/N: TD4P9-00 Mating Connector (ordered separately) P/N: TD4P9-03M 3 meter molded cable assembly (ordered separately) Other Lengths Available Wire Code for Voltage units: Red = + Power supply Black = Common White = Green = Digital (optional) Wire Code for Current units: Red = + Power Supply Black = /8 Hex Voltage units Power Supply + Digital (optional) Common M12 MATING CABLE ASSEMBLIES VOLTAGE OUTPUT TRANSDUCERS ONLY M12 with 2 LEDs (green and yellow) Green shows power, Yellow shows digital output P/N: TDM12-4F69-CR2L-01M 1 meter molded cable assembly for voltage outputs only Current Units Pin 1 + power Supply Pin 2 N/C Pin 3 Pin 4 N/C CURRENT OUTPUT TRANSDUCERS ONLY M12 with no LEDs P/N:TDM12-4F69-CR-01M 1 meter molded cable assembly for 4-20mA outputs (no digital output available with 4-20mA outputs) Other Lengths Available Wire Code for voltage units: Brown = + Power Supply White = Blue = Common Black = Digital (optional) Wire Code for Current units: Brown = + Power Supply Blue = Dimensions In Inches And Are Reference Only.

5 SPECIFICATIONS Performance Overange Protection Burst Pressure Pressure Cycles Internal Update Time Digital 25 C (77 F) 0.25% / 0.1% BFSL(includes: Non-linearity, Hysteresis and Non-repeatability) 2x Rated Pressure or optional 4x and 10x see ordering chart - up to 6000 psi (690 bar) (optional higher ranges available) 5x or 20,000 psi, whichever is less >100 million <=1msec Optional digital output for pressure or temp switch point (not available on 4-20mA output units) Environmental Data Temperature Compensated Temperatures -20 to 85 C (-4 to 185 F) Operating Temperatures -40 to 100 C (-40 to 212 F) Storage -40 to 125 C (-40 to 250 F) Thermal Limits TC Zero <+1.5% of FS TC Span <+1.5% of FS Long Term Drift 0.2% FS/year (non-cumulative) Shock 100g, 11 ms, 1/2 sine Vibration 20g, peak, 20 to 2400 Hz EMI/FRI Protection Yes Rating Up to IP-69K available (high pressure wash down) Mechanical Configuration Pressure Connections Wetted Material Case(housing) Electrical Data Excitation Impedance Current Consumption Noise Reverse Polarity Protection Set Point % for Pressure or Temp See ordering chart 17-4PH stainless steel (for other materials consult factory) Cable, 9.4 Din, IP-69K 4 pin M12 Connector 304 stainless steel 10-28VDC, Typ (must be at least 0.5V above full output voltage) see ordering chart <100 Ohms, Nominal 25mA max (current output), <5mA (voltage output) <2mV RMS Yes For pressure, this is done by selecting a percentage of your transducer s full range and this will be the set point (40% of a 1000 psi range will have the set point at 400psi) P40. For temperature, select what percentage of 80 C you want the set point to be (70% of 80 C is 56 C [132.8 F] and this will be the set point) T70. ORDERING Series TD1000 D Type G 1000 (psi) Pressure Port 03 Q00 2 Pressure or Temp Set Point % (P or T) T40 TD1000= 2X Over Pressure TD1004= 4X Over Pressure (up to 5000 psi) TD1010= 10X Over Pressure (up to 2000 psi) B= 4-20mA G= Gauge C= 0-5 vdc D= 0-10 vdc H= 1-5 vdc J= 1-6 vdc G= vdc (voltage outputs are 3 wire nonratiometric) = 1/4 NPT Male 09= 7/16 x 20 Q00= IP69K M12 D00= 4 pin Mini 9.4 DIN = Consult factory for further options Consult factory for quick ship versions 2= 0.25% 0= 0.1% X= no SP P or T10= 10% P or T20= 20% P or T30= 30% P or T40= 40% P or T50= 50% P or T60= 60% P or T70= 70% P or T80= 80% P or T90= 90% (of full range) (full temp range is 0 to 80 C) Pressure and temp set points are available with voltage outputs only Rev 4.10

6 The TDH30 Series Low Cost OEM Pressure Transducer SERIES: TDH30 APPLICATIONS Hydraulic / Mobile Hydraulic Pneumatic Systems Food and Beverage Industry Refrigeration Systems Pumps and Compressors Energy and water management Construction and Agricultural Equipment FEATURES Vacuum to 10,000 psi Range Various s Compact Design 316 Stainless steel Wetted Parts DESCRIPTION The TDH30 Series Pressure Transducer utilizes piezoresistance technology in an all stainless steel body. It is compact in size, has long term stability, ease of installation and is very economical as well as reliable. The TDH30 sets a new price-performance standard for low cost, high volume commercial and industrial applications. Low Cost Industrial 1% Custom s and Ranges Available OEM Tested and Approved ELECTRICAL CONNECTIONS Signal Function Color Pin Electrical Connector 0-5V Supply V + Red 1 Com Black 2 White 3 N/A N/A 4 DIN 4 pin (9.4) mA Supply V Red 1 Black 2 Signal Function Color Pin Com - A 0-5V Supply + - B + - C 4-20mA - A Supply + - B 3 pin Packard A B C

7 SPECIFICATIONS Input Supply Voltage Proof Pressure Burst Pressure Fatigue Life Performance 1% Stability VDC Vac to 10,000 psi 1.5 x full scale 3 x full scale More than 4 million cycles 0.2% full scale Compensated Temperatures -10 to 75 C (14 to 167 F) Operating Temperatures -20 to 80 C (-4 to 176 F) Zero and Span Offset Tolerance 1.5% Mechanical Configuration Pressure Port 1/4 NPT (standard) * 9.4 mini DIN, 3 pin Packard * Sealing Rating Wetted Parts For best performance use shielded cables Mating connectors and cable assemblies sold separately * = Consult factory for further OEM options IP65 with T-Direct standard 9.4 DIN cable 316 stainless steel Dimensions Dimensions are in mm and for reference only ORDERING Series TDH30 B Pressure Type G 0500 psi Pressure Port 03 D00 4 B= 4-20mA C= 0-5V (3 wire) G = Gauge = 1/4 NPT Male D00= 4 pin Mini 9.4 DIN B00= 3 pin Packard 4= 1% = Consult factory for further OEM options Pressure ranges listed above are quick ship versions Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Direct web site, it is up to the customer to determine the suitability of the product in the application. REV: 5.10

8 The TDH40 Series Better, Low Cost OEM Pressure Transducer SERIES: TDH40 APPLICATIONS Hydraulic / Mobile Hydraulic Pneumatic Systems Food and Beverage Industry Refrigeration Systems Pumps and Compressors Energy and water management Construction and Agricultural Equipment FEATURES Vacuum to 10,000 psi Range Various s Compact Design 316 Stainless steel Wetted Parts DESCRIPTION The TDH40 Series Pressure Transducer utilizes piezoresistance technology in an all stainless steel body. It is compact in size, has long term stability, ease of installation and is very economical as well as reliable. The TDH40 sets a new price-performance standard for low cost, high volume commercial and industrial applications. Low Cost Better 0.4% Custom s and Ranges Available OEM Tested and Approved ELECTRICAL CONNECTIONS TDH40 M12 pin assignments Voltage outputs pin 1 = Voltage Supply + pin 2 = pin 3 = Com pin 4 = N/C 4-20mA output pin 1 = Voltage Supply + pin 2 = N/C pin 3 = pin 4 = N/C

9 SPECIFICATIONS Input Supply Voltage Proof Pressure Burst Pressure Fatigue Life Performance 0.4% Stability VDC Vac to 10,000 psi 1.5 x full scale 3 x full scale More than 4 million cycles 0.2% full scale Compensated Temperatures -10 to 75 C (14 to 167 F) Operating Temperatures -20 to 80 C (-4 to 176 F) Zero and Span Offset Tolerance 1.5% Mechanical Configuration Pressure Port 1/4 NPT (standard) * M12 * Sealing Rating Wetted Parts For best performance, use shielded cables Mating cable assemblies sold separately * = Consult factory for further OEM options IP67 when used with T-Direct TDM12 cable 316 stainless steel Dimensions 4 ORDERING Dimensions are in mm and for reference only Series TDH40 B Pressure Type G 0500 psi Pressure Port 03 Q00 5 B= 4-20mA C= 0-5V (3 wire) G = Gauge = 1/4 NPT Male Q00= M12 D00= 9.4 mini DIN 5= 0.4% = Consult factory for further OEM options Pressure ranges listed above are quick ship versions Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Direct web site, it is up to the customer to determine the suitability of the product in the application. REV: 5.10

10 The TDH10 Series Low Cost, Higher Pressure, 0-10V, OEM Pressure Transducer SERIES: TDH10 APPLICATIONS Hydraulic / Mobile Hydraulic Pneumatic Systems Food and Beverage Industry Refrigeration Systems Pumps and Compressors Energy and water management Construction and Agricultural Equipment FEATURES Vacuum to 15,000 psi Range Various s including 0-10V 316 Stainless steel Wetted Parts DESCRIPTION The TDH10 Series Pressure Transducer utilizes piezoresistance technology in an all stainless steel body. It has long term stability, ease of installation and is very economical as well as reliable. The TDH10 sets a new price-performance standard for low cost, high volume commercial and industrial applications. Low Cost Industrial 1% Custom s and Ranges Available OEM Tested and Approved ELECTRICAL CONNECTIONS Signal Function Color Pin Electrical Connector 0-10V Supply V + Red 1 Com Black 2 White 3 N/A N/A 4 DIN 4 pin (9.4) mA Supply V Red 1 Black 2 Signal Function Color Pin Com - A 0-10V Supply + - B + - C 4-20mA - A Supply + - B 3 pin Packard A B C

11 SPECIFICATIONS Input Supply Voltage Proof Pressure Burst Pressure Fatigue Life Performance VDC 0.4% Long Term Drift Vac to 15,000 psi 1.5 x full scale 3 x full scale More than 4 million cycles 0.2% full scale Compensated Temperatures -10 to 75 C (14 to 167 F) Operating Temperatures -20 to 80 C (-4 to 176 F) Zero and Span Offset Tolerance 0.5% Mechanical Configuration Pressure Port 1/4 NPT (standard) * 9.4 mini DIN, 3 pin Packard * Wetted Parts Mating connectors and cable assemblies sold separately * = Consult factory for further OEM options 316 stainless steel Dimensions Dimensions are in mm and for reference only ORDERING Series TDH10 B Pressure Type G 0500 psi Pressure Port 03 D00 5 B= 4-20mA G = Gauge D= 0-10V (3 wire) ,000 15,000 03= 1/4 NPT Male D00= 4 pin Mini 9.4 DIN B00= 3 pin Packard 5= 0.4% = Consult factory for further OEM options Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Direct web site, it is up to the customer to determine the suitability of the product in the application. REV: 4.10

12 The TDH31 Series Low Cost OEM Vacuum and Compound Range Pressure Transducer 31 SERIES: TDH31 APPLICATIONS Hydraulic Pneumatic Systems Food and Beverage Industry Refrigeration Systems Energy and water management Construction and Agricultural Equipment FEATURES Vacuum to 85 psig Ranges Various s Compact Design 316 Stainless steel Wetted Parts ELECTRICAL CONNECTIONS DESCRIPTION The TDH31 Series Pressure Transducer utilizes piezoresistance technology in an all stainless steel body. It is compact in size, has long term stability, ease of installation and is very economical as well as reliable. The TDH31 sets a new price-performance standard for low cost, high volume commercial and industrial applications. Low Cost Industrial 1% Custom s and Ranges Available OEM Tested and Approved Signal Function Color Pin Electrical Connector 0-5V Supply V + Red 1 Com Black 2 White 3 N/A N/A 4 DIN 4 pin (9.4) Com - 2 Load N/C VDC V+ 4 3 N/C 4-20mA Supply V Red 1 Black 2 Signal Function Color Pin 3 pin Packard Load 1 N/C - + V+ 4-20mA

13 SPECIFICATIONS Input Supply Voltage VDC Vacuum to 85 psig * Proof Pressure Burst Pressure Fatigue Life Performance Stability 1.5 x full scale 3 x full scale More than 4 million cycles 1% full scale 0.2% full scale Compensated Temperatures -10 to 75 C (14 to 167 F) Operating Temperatures -20 to 80 C (-4 to 176 F) Zero and Span Offset Tolerance 1.5% Mechanical Configuration Pressure Port 1/4 NPT (standard) * 9.4 mini DIN, 3 pin Packard * Sealing Rating Wetted Parts For best performance use shielded cables Mating connectors and cable assemblies sold separately * = Consult factory for further OEM options IP65 with T-Direct standard 9.4 DIN cable 316 stainless steel Dimensions Dimensions are in mm and for reference only ORDERING Series TDH31 B Pressure Type G V000 psi Pressure Port 03 D00 5 B= 4-20mA C= 0-5V (3 wire) G = Gauge Vac-0= V000 Vac-15= V015 Vac-45= V045 Vac-85= V085 03= 1/4 NPT Male D00= 4 pin Mini 9.4 DIN 4= 1% = Consult factory for further OEM options Pressure ranges listed above are quick ship versions Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Direct web site, it is up to the customer to determine the suitability of the product in the application. REV: 5.10

14 The TDH41 Series Low Cost, Higher, OEM Vacuum and Compound Range Pressure Transducer 41 1 SERIES: TDH41 APPLICATIONS Hydraulic Pneumatic Systems Food and Beverage Industry Refrigeration Systems Energy and water management Construction and Agricultural Equipment FEATURES Vacuum to 85 psig Ranges Various s Compact Design 316 Stainless steel Wetted Parts ELECTRICAL CONNECTIONS DESCRIPTION The TDH41 Series Pressure Transducer utilizes piezoresistance technology in an all stainless steel body. It is compact in size, has long term stability, ease of installation and is very economical as well as reliable. The TDH41 sets a new price-performance standard for low cost, high volume commercial and industrial applications. Low Cost Better 0.4% Custom s and Ranges Available OEM Tested and Approved Signal Function Color Pin Electrical Connector 0-5V Supply V + Red 1 Com Black 2 White 3 DIN 4 pin (9.4) 3 Com - 2 Load N/C - + V VDC N/C 3 4 not used 2 1 V+ 4-20mA Supply V + Red 1 Black 2 4 N/C Load Signal Function Color Pin 0-5V 4-20mA Supply V + Brown 1 + White 2 Com Blue 3 Supply V + Brown 1 Blue 3 M12 not used 4-20mA + - N/C 4 V Com 3 Load 0-5VDC - Load N/C V+ 2 N/C 4-20mA

15 SPECIFICATIONS Input Supply Voltage VDC Vacuum to 85 psig * Proof Pressure Burst Pressure Fatigue Life Performance Stability 1.5 x full scale 3 x full scale More than 4 million cycles 0.4% full scale 0.2% full scale Compensated Temperatures -10 to 75 C (14 to 167 F) Operating Temperatures -20 to 80 C (-4 to 176 F) Zero and Span Offset Tolerance 1.5% Mechanical Configuration Pressure Port 1/4 NPT (standard) * 9.4 mini DIN, 3 pin Packard * Sealing Rating Wetted Parts For best performance use shielded cables Mating connectors and cable assemblies sold separately IP65 with T-Direct standard 9.4 DIN cable IP67 with T-Direct standard TDM12 cable 316 stainless steel 4 Dimensions Dimensions are in mm and for reference only ORDERING Series TDH41 B Pressure Type G V000 psi Pressure Port 03 D00 5 B= 4-20mA C= 0-5V (3 wire) G = Gauge Vac-0= V000 Vac-15= V015 Vac-45= V045 Vac-85= V085 03= 1/4 NPT Male D00= 4 pin Mini 9.4 DIN Q00= M12 5= 0.4% = Consult factory for further OEM options Pressure ranges listed above are quick ship versions Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Direct web site, it is up to the customer to determine the suitability of the product in the application. REV: 5.10

16 Introducing the TDA08 Standard Size, Up to 10,000 psi, 0.5% Pressure Transducer SERIES: TDA08 FEATURES High Strength Stainless Steel Construction No Silicone Oil, no Internal O-rings Wide operating temperature range Ranges up to 10,000 psi Low static and thermal errors Unparalleled price/performance ratio Stainless steel case Compatible with wide range of gases and liquids Suitable for high shock and vibration applications APPLICATIONS Industrial OEM Equipment Hydraulic Systems HVAC/R Equipment Refrigeration O road Test Stands Data Loggers Construction and Agricultural Equipment Energy and Water Management Pressure Instrumentation DIMENSIONS Dimensional Data (Millivolt only) 9.4mm Standard Packard Connector 9.4 Standard + N/C +V Supply +V Supply Dimensions In Millimeters And Are Reference Only.

17 SPECIFICATIONS 25 C (77 F) 1 < ± 0.5% BFSL Stability (1 year) ±0.25%FS, typ Overange Protection 2X Rated Pressure Burst Pressure 5X or 20,000 psi whichever is less. Pressure Cycles >100 Million 1 includes:non-linearity, Hysteresis and Non-repeatability Environmental Data Temperature Operating -40 to 85 C (-40 to 185 F) Storage -40 to 125 C (-40 to 250 F) Thermal Limits TC Zero <±1.5% of FS TC Span <±1.5% of FS Other Shock 100G, 11msec, 1/2 sine Vibration 20G peak, 20 to 2400 Hz. EMI/RFI Protection: Yes Rating: IP-66 Physical Description Wetted Material 17-4PH stainless steel (for other materials, consult factory) Electrical Conn. Cable, DIN or Packard Metripack Case (housing) 304 stainless steel Electrical Data Excitation 10-28VDC, Typ VDC, Typ. 4-20mA Voltage (1-5V, 1-6V) Impedance - <100 Ohms, Nominal Current Consumption 25mA max <10mA Bandwidth (-3dB): DC to 250 Hz (-3dB): DC to 1kHz Noise <2mV RMS <2mV RMS Load See Load Line Curve 10k Ohms, Min. Reverse Polarity Yes Yes Protection ORDERING Series TDA08 B Pressure Type G in psi 1000 Electrical Connection D Cable Length 00 3 TDA08 = Consult factory for further options. B= 4-20ma (2 wire) G = Gauge H= 1-5 vdc (3 wire) J= 1-6 vdc (3 wire) K= vdc Ratiometric (3 wire) N= 50mV (4 wire) K B= Packard D= 4 pin Mini 9.4 DIN C= Cable 00= None 02= 2 feet 04= 4 feet 06= 6 feet 3= 0.5% cationsmay change without notice. The informationwe supply is believed to be accurate and r eliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Directweb site, it is up to the customer to determine the suitability of the product in the application. REV: 10.09

18 Introducing the TDA21 series 1/2 Inch Conduit Electrical Connection, Pressure Transducer SERIES: TDA21 FEATURES APPLICATIONS High Strength Stainless Steel Construction No Silicone Oil, No Welds, No Internal O-rings Wide Operating Temperature Range Ranges from Vacuum to 10,000PSI Low Static and Thermal Errors Unparralled Price and Performance Rugged Design Survives Harsh Environments Wide Media Compatibility Suitable for High Shock and Vibration Applications Refrigeration Industrial OEM Equipment Oil & Gas Platforms Test Stands Pressure Instrumentation Gas Compression & Storage Energy & Water Management Pressure Instrumentation Process Control DESCRIPTION The TDA21 is a high accuracy, high quality all stainless steel media isolated pressure sensor intended for use in the measurement of gases and liquids compatible with stainless steel. This pr for applications with demanding price and performance requirements. The TDA21 o ers a wide range outputs. The high strength stainless steel construction contains no silicone oil, no welds and no internal O-rings. Measure - ments are available in gauge pressure covering ranges up to 10,000 PSI!

19 SPECIFICATIONS 25ºC (77oF) 1 < ± 0.25% BFSL Stability (1 year) ±0.25%FS, typ Overange Protection 2X Rated Pressure Burst Pressure 5X or 20,000 psi whichever is less. Pressure Cycles >100 Million Agency Approval UL1604 (CSA 213) Class I, Div II, Groups A, B, C & D 1 includes:non-linearity, Hysteresis and Non-repeatability Environmental Data Temperature Operating -40 to 85 C (-40 to 185 F) Storage -40 to 125 C (-40 to 250 F) Thermal Limts Compensated Range 0 to 55 C (30 to 130 F) TC Zero <±1.5% of FS (±3.0% for 0-25 psi) TC Span <±1.5% of FS Other Shock 100G, 11msec, 1/2 sine Vibration 20G peak, 20 to 2400 Hz EMI/RFI Protection 100V/m,150KHz to 1GHz Rating IP-65 Physical Description Wetted Material 17-4PH stainless steel NACE compatible (for other materials, consult factory) 1/2 conduit pipe w/cable (for other cable lengths, consult factory) Case (housing) 304 stainless steel Electrical Data Excitation 10-28VDC, Typ VDC,Typ. 5VDC 4-20mA Voltage (1-5V) V Ratiometric Current Consumption 20mA max <10mA <5mA Bandwidth (-3dB) (-3dB) (-3dB) DC to 250 Hz DC to 1kHz DC to 1kHz Zero O set <±1.0% <±1.0% <±1% of FS Span Tolerance <±2.0% <±1.5% <±2% of FS Noise - <2mV RMS <2mV RMS Load See Below 10k Ohms, Min. 1 0k Ohms, Min. Reverse Polarity Protection Yes Yes No

20 DIMENSIONS Dimensional Da ta Dimensions In Inches And Are Reference Only. ORDERING Series TDA21 B Pressure Type G 1000 Pressure Port 03 O Cable Length 04 2 TDA21 B= 4-20ma G = Gauge H= 1-5 vdc J= 1-6 vdc K= vdc (ratiometric) 0025 = 0-25 psi 0050= 0-50 psi 0100= psi 0200= psi 0500= psi 1000= psi 2500= psi 5000= psi 7500= psi 010K= 0-10,000 psi 01= 1/8 NPT male 03= 1/4 NPT male 04= 1/4 NPT female 06= 1/2 NPT male O= 1/2 male conduit 02= 2ft 04= 4ft 06= 6 ft 2= 0.25% = Consult factory for further options. cationsmay change without notice. The informationwe supply is believed to be accurate and r eliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Directweb site, it is up to the customer to determine the suitability of the product in the application. REV: 10.09

21 Introducing the TDA22 Series Wet/Wet Differential Pressure Transducer. SERIES: TDA22 FEATURES Compact and Rugged Design High Strength Stainless Steel Construction No Internal Fluid Filled Cavities No Internal O-rings Wide Operating Temperature Range Low static and thermal errors EMI/RFI Protection to 100V/m Suitable for high shock and vibration applications APPLICATIONS Industrial OEM Equipment Hydraulic Systems Train Braking Circuits HVAC/R Equipment Refrigeration Offroad Test Stands Data Loggers Filtration Energy and Water Management DESCRIPTION The Model TDA22 offers wet/wet differential pressure mea - surements of gases and liquids compatible with stainless steel. The compact size contains no internal O-rings or fluid filled cavities, making it ideal for water management, gas pipeline instrumentation, filtration, natural gas compressors and many other applications. In the even that either pres - sure port is at full line pressure and the other at zero, no damage will be done to the transducer/transmitter. The Model TDA22 has been designed specifically for ap - plications with demanding price and performance require - ments. Measurements are available in differential pressures covering line pressures up to 1,000PSI. DIMENSIONS Dimensional Da ta Line Impedance mA LOAD LINE CURVE Supply Voltage Dimensions In mm And Are Reference Only.

22 SPECIFICATIONS 25ºC (77ºF) Line Pressure Measurment Range Proof Pressure Burst Pressure 1 Pressure Cycles 1 includes:non-linearity, Hysteresis and Non-repeatability Environmental Data Temperature Operating Storage Thermal Limts Compensated Range Total Error Band Total Error = RSS of zero offset, span tolerance, TC zero, TC span and accuracy. Other to 1000 PSI (0-7, 0-17, 0-35 and 0-70 Bar) 20% of line pressure, minimum Rated line pressure on either P1 or P2 5 times the rated line pressure or 2,000PSI, whichever is less < ± 0.3% BFSL >10 Million -40 to 85 C (-40 to 185 F) -40 to 100 C (-40 to 212 F) 0 to 55 C (30 to 130 F) ±1.5% of FS Shock 100G, 11msec, 1/2 sine Vibration 10G peak, 20 to 2000 Hz. EMI/RFI Protection 100V/m, 150kHz to 1GHz Rating IP-66 Physical Description Wetted Material 17-4PH and 316L stainless steel Pressure Port 1/8 NPT female Case (housing) 304 stainless steel s DP range Line pressure Burst Pressure (PSI), min* (PSI), max (PSI) Electrical Data Excitation 10-30VDC 10-30VDC, Typ. 5VDC 4-20mA Voltage (.25-5V, 1-5V, 1-6V) V Ratiometric Impedance - <100 Ohms, Nominal <100 Ohms, Nominal Current Consumption < 25mA <10mA <10mA Bandwidth (-3dB): DC to 250 Hz (-3dB): DC to 1kHz (-3dB): DC to 1kHz Load See Load Line Curve 10k Ohms, Min. 10K Ohms, Min. Reverse Polarity Protection Yes Yes No ORDERING Series TDA22 B Pressure Type G Differential Pressure Range in psi 0020 Pressure Port 02 C Cable Length TDA22 B= 4-20ma (2 wire) G = Gauge H= 1-5 vdc (3 wire) J= 1-6 vdc (3 wire) K= vdc ratiometric (3 wire) S= 10mV/V (4 wire) (5V supply) 0020 = 0-20psi DP 02= 1/8 NPT female F= 4 pin Mini 8.0 DIN 050 = 0-50psi DP C= Cable 0100 = 0-100psi DP O= 1/2 NPT conduit 0200 = 0-200psi DP w/ 2ft cable 00= None 02= 2 feet 04= 4 feet 06= 6 feet 3= 0.5% 3 = Consult factory for further options. Specificationsmay change without notice. The information we supply is believed to be accurate and r eliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Directweb site, it is up to the customer to determine the suitability of the product in the application. REV: 07.06

23 Introducing the TDA31 High Pressure, 0.25%, Pressure Transducer SERIES: TDA31 DESCRIPTION The TDA31 is a competitively priced, high quality all stainless steel media isolated Pressure Sensor intended for use in the measurement of various liquids compatible with stainless steel. This series is suitable for test stands, water jets, pumps and pipeline instrumentation. TDA31 pressure sensors and transducers have been designed with EMI/RFI protection against electrical noise including ignition systems. TDA31 sensors and transducers o er both millivolt and high level outputs. The high strength stainless steel sensing element is machined from a solid piece of stainless steel, resulting in construction that contains no silicone oil, no welds and no internal O-rings. Measurements are available in gauge pressure covering ranges up to 60,000 psi. FEATURES High High Strength Stainless Steel Construction No Silicone Oil, no Internal O-rings, no welds (50 psi & above) Wide operating temperature range Ranges from 10K to 60K psi Fully welded case provides rugged design Compatible with wide range of liquids Suitable for high shock and vibration applications APPLICATIONS Hydraulic Systems Water Jets Test Stands Pipeline Instrumentation High Pressure Wells Pumps

24 SPECIFICATIONS 25 C (77 F) 1 < ± 0.25% BFSL Stability (1 year) ±0.5%FS, typ 1 includes: Non-linearity, Hysteresis and Non-repeatability Pressure Cycles >100 Million Environmental Data Temperature Operating -40 to 85 C (-40 to 185 F) Storage -40 to 125 C (-40 to 250 F) Thermal Limts Compensated Range 0º to 55 C (30º to 130 F) TC Zero <±1.5% of FS TC Span <±1.5% of FS Other Shock 100G, 11msec, 1/2 sine Vibration 20G peak, 20 to 2400 Hz. EMI/RFI Protection: Yes Rating: IP-66 Physical Description Wetted Material 17-4PH stainless steel NACE compatible (for other materials, consult factory) Cable, DIN, or Bendix 6 pin Case (housing) 304 stainless steel (for other materials, consult factory) Electrical Data Excitation 10-28VDC, Typ VDC, Typ. 5VDC 4-20mA Voltage (3 or 4 Wire) 0-50mV Impedance >10K ohms <100 Ohms, Nominal 1100 Ohms, Nominal Current Consumption 20mA typical <10mA <5mA Bandwidth (-3dB): DC to 250 Hz (-3dB): DC to 1kHz (-3dB): DC to 5kHz, min Zero O set <±1% of FS <±1% of FS <±2% of FS Span Tolerance <±2.0% of FS <±1.5% of FS <±2% of FS Noise Not Applicable <2mV RMS Not Applicable Load VDC 10k Ohms, Min. > 1M Ohms Reverse Polarity Protection Yes Yes Not Applicable s Psi, gauge Pressure Connection 0-10,000 psi 1/4 BSP male or 1/4 NPT female 0-15,000 psi 1/4 BSP male or 1/4 NPT female 0-20,000 psi 9/16-18 UNF male with 37 flare 0-45,000 psi F250C female autoclave 0-60,000 psi M16 x 1.5 female with sealing cone

25 DIMENSIONS 1/4" NPT Female Rated to 15,000 PSI F250C Female Autoclave Rated to 45,000 PSIG Rated to 15,000 PSIG Rated to 20,000 PSIG Dimensions In Inches And Are Reference Only ORDERING Series TDA31 D PressureType G in psi 020K PressurePort 04 S6 Cable Length 00 2 TDA31 B= 4-20ma (2 wire) H= 1-5 vdc (3 wire) C= 0-5 vdc (3 wire) D= 0-10V (3 wire) G = Gauge 010K= 10,000 psi 015K= 15,000 psi 020K= 20,000 psi 045K= 45,000 psi 060K= 60,000psi 13= 1/4 BSP male rated 10K psi 04= 1/4 NPT female rated 10K psi 24= 9/16-18 UNF male with 37 flare rated 20,000 psi 27= F250C female autoclave rated 45,000 psi 36= M16 x 1.5 female with sealing cone rated 60,000 psi S2= Six Pin Bendix w/ 4-20mA output S6= Six pin Bendix w/ voltage output F= 4 pin Mini 8.0 DIN C= Cable 00= None 02= 2 feet 04= 4 feet 06= 6 feet 2= 0.25% = Consult factory for further options. Installation/Application: The purchaser is responsible for the media compatibility, functional adequacy and correct installation of the transducer. cationsmay change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Direct web site, it is up to the customer to determine the suitability of the product in the application. REV: 10.09

26 Introducing the TDG series Absolute, Vacuum, Compound Range, High, Industrial Pressure Transducers SERIES: TDG03 FEATURES Gauge- Absolute, Vacuum and Compound Pressure Models Available High Stability Achieved by CVD Sensoring Element Voltage and Current Models Custom pressure ranges available ASIC Technology, No Zero/Span Potentiometers DESCRIPTION The TDG series features stability and accuracy in a variety of enclosure options. The TDG series extends the packaging options via an all welded stainless steel back end for demanding industrial applications. The TDG series feature proven CVD sensing technology, an a sensor line that can easily accommodate specials while ELECTRICAL CONNECTIONS Power Supply Requirements Voltage Units: 1.5 vdc 0ver Max to 35 vdc for voltage outputs Current Units: 7-35vdc for 4-20 ma output Voltage Units Red= +Power Black= -Power White= Voltage Units 9.4 mini DIN Current Units Red= +Power Black= Pin 1 +Power Supply Current Units Pin 1 +Power Supply Pin 2 Pin 3 N/C Pin 4 Gr Dimensions In Inches And Are Reference Only. MATING CONNECTOR P/N: TD4P9-00 Mating Connector (ordered separately) P/N: TD4P Meter Molded Cable Assembly Other Lengths Available 3/4 Hex

27 SPECIFICATIONS Input Proof Pressure Burst Pressure Vacuum to 25 bar (285 psi) compound, 0 to 25 bar (300 psi) absolute 2 x Full Scale (FS) >35 x FS <= 6 bar (100 psi); >20 x FS >=60 bar (1000 psi); Fatigue Life Designed for more than 100 million FS cycles Performance Long Term Drift 0.2% FS/year (non-cumulative) 0.25% / 0.5% FS typical (optional 0.15%) Thermal Error 1.5% FS typical (optional 1% FS) Compensated Temperatures -20 to 80 C (-5 to 180 F) Operating Temperatures -40 to 125 C (-22 to 260 F) for the mini DIN -20 to 80 C (-5 to 180 F) for the NEMA 4 Cable -20 to 50 C (-5 to 125 F) for the IP67 Cable Zero Tolerance Span Tolerance Response Time Pressure Port Wetted Parts Enclosure Vibration Acceleration Shock s Weight 1% of span 1% of span 0.5 ms See ordering chart 17-4 PH Stainless Steel See ordering chart 316 ss, 17-4 PH ss IP65 for the mini DIN and NEMA Cable versions IP67 for IP67 Cable version IP68 for Submerssible versions (max. depth 200meters H20) 70g, peak to peak sinusoidal, 5 to 2000 Hz (Random Vibration: 20 to 2000 ı 20g Peak per MIL-STD.-810E Method 514.4) 100g steady acceleration in any direction 0.032% FS/g for 1 bar (15 psi) range decreasing logarithmically to % FS/g for 400 bar (6000 psi) range. 20g, 11 ms, per MIL-STD.-810E Method Procedure All voltage outputs are 3 wire non-ratiometeric, current output is 2 wire Approx. 100 grams (additional cable; 75 g/m) ORDERING Series TDG03 D Pressure Type G V015 psi Pressure Port 03 D Cable Length 00 2 TDG03 B= 4-20ma H= 1-5 vdc K= vdc D= 0-10 vdc C= 0-5 vdc G = Gauge A = Absolute vac-0 = V000 vac-15 = V015 vac-45 = V045 vac-85 = V085 vac-135 = V135 vac-185 = V185 vac-285 = V285 03= 1/4 NPT Male 09= 7/16 x 20 SAE #4 (J1926-2) 01= 1/8 NPT MALE OR Pressure Type A= Absolute J= IP67 Cable D= 4 pin Mini 9.4 DIN C= Cable (IP65) 0060 psi 00= None 01= 1 meter 2= 0.25% 1= 0.15% = Consult factory for further options REV: 5.10

28 Introducing the TDG05 Series Very Low Differential Transducer. SERIES: TDG05 FEATURES For Air or Non-Conductive Gas 0.25 to 100 Inches in W.C.(differential) /±0.1 to ±50 Inches in W.C. (bidirectional) High Proof Pressure APPLICATIONS HVAC Energy Management Systems Variable Air Volume and Fan Control (VAV) Environmental Pollution Control Static Duct and Clean Room Pressures Oven Pressurization and Furnace Draft Controls DESCRIPTION TheTDG05 Series are very low-pressure transducers for ranges as low 0.25~ W.C. and feature ±1 % full scale static accuracy. Primarily used in Building Energy Manage - ment, these transducers are capable of measuring pres - sures and flows with the accuracy necessary for proper building pressurization and air flow control. TDG865 Series transducers utilize an all-stainless steel micro-tig welded sensor that allows up to 10 psi overpressure (in either direction) with no damage to the unit. All sensor compo - nents have thermally matched coefficients, which promote improved temperature performance and excellent long-term stability. SPECIFICATIONS A tensioned stainless steel diaphragm and insulated stainless steel electrode, positioned close to the diaphragm, form a variable capacitor. Positive pressure moves the diaphragm toward the electrode, increasing the capacitance. A decrease in pressure moves the diaphragm away from the electrode, decreasing the capacitance. The change in capacitance is detected and converted to a linear DC electrical signal by T-Direct s unique electronic circuitry. Input Proof Pressure Fatigue Life Performance Supply Voltage Thermal Error Zero Thermal Error Span Compensated Temperatures Operating Temperatures Storage Temperatures 0.25~ to 100~ WC 10 psi 10 psi, max. (Vs) 9-30 Vdc ±1.0% FS (Standard);.4% &.25% versions available ±0.033% FS/ F (±0.06% FS/ C) ±0.033% FS/ F (±0.06% FS/ C) 0 F to +150 F (-18 C to +65 C) 0 F to +150 F (-18 C to +65 C) -40 F to +185 F (-40 C to +85 C) Specifications continued on next page

29 Zero Tolerance Span Tolerance Mechanical Configuration Pressure Port Wetted Parts Enclosure Approvals Weight Individual Specifications Voltage Units Min. Load Resistance Current Units Max. Loop Resistance 1% (.5% for high accuracy option) 1% (.5% for high accuracy option) 1/4~ Fitting Stainless Steel and Glass-Filled Polyester Screw Terminal Strip Fire Retardant Glass-Filled Polyester; Option A1 Conduit Enclosure Available CE 3 oz 0-5 Vdc or 0-10 Vdc (3 wire) (see ordering chart) 5000 kohms 4-20 ma (2 wire) DIMENSIONS ndard TDG SCREW W/TERMINAL WASHERS 3 PLACES H I G H L O W SCREW W/TERMINAL WASHERS 3 PLACES ORDERING Series TDG05 Undirectional Range U3 Bidirectional Range B7 A 01 A U1 = 0 to 0.25 U2 = 0 to 0.5 U3 = 0 to 1.0 U4 = 0 to 2.5 U5 = 0 to 5.0 U6 = 0 to 10.0 U7 = 0 to 25.0 U8 = 0 to 50.0 U9 = 0 to B1 = +/- 0.1 B2 = +/ B3 = +/- 0.5 B4 = +/- 1.0 B5 = +/-2.5 B6 = +/- 5.0 B7 = +/ B8 = +/ B9 = +/ A = 4-20mA B = 0-5VDC 1 = Terminal Strip 2 = Enclosure with 7/8 Knock-Out Hole for 1/2 Conduit A = +/- 1% FS (standard) Option (with Calibration Certificate) B = +/- 0.4% FS C = +/- 0.25% FS D = +/- 1% FS = Consult factory for further options. Specificationsmay change without notice. The informationwe supply is believed to be accurate and r eliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Directweb site, it is up to the customer to determine the suitability of the product in the application. Note: Not all combinations are available.minimum quantity orders apply. Contact the factory for more details. REV: 05.06

30 Introducing the TDG07 3A Sanitary Pressure Transducer. SERIES: TDG07 FEATURES APPLICATIONS For Clean-In-Place (CIP) and 0.20% Full Scale No Liquid Fill Diaphragms Food Processing Dairy & Beverage Processing Pharmaceutical Processing Sanitary Pipelines DESCRIPTION The TDG07 meets 3A sanitary design standards and is fully sealed to withstand external high pressure washdowns. These units are packaged in rugged welded stainless steel housings and are exceptionally insensitive to vibration, shock and environmental extremes. A small size and triclover sanitary pressure fitting allow direct mounting in most CIP and SIP installations. Other features include IC-based circuitry, a 1/2 NPT conduit fitting and shielded cable with vent tube. Sealed screws provide access to zero and span adjustments. A stainless steel diaphragm and an insulated electrode form a variable capacitor. Pressure on the diaphragm alters the sensor s capacitance, which is then detected and converted to a highly accurate linear 4-20 ma signal by electronic circuitry featuring our patented charge-balance principle. Low hysteresis, very stable operation and negligible clamping effect are inherent.

31 SPECIFICATIONS Input Vacuum to 1000 psig Proof Pressure see ordering chart Burst Pressure see ordering chart Fatigue Life >1 million cycles Performance 4-20 ma (2 Wire) Supply Voltage (Vs) Vdc 0.20% FS Thermal Error Zero 0.02% FS/ Thermal Error Span 0.02% FS/ Compensated Temperatures 20 Operating Temperatures -40 Storage Temperatures -65 Zero Tolerance 1% FS (±0.5 ma adjustable) Span Tolerance 1% FS (±0.5 ma adjustable) Maximum Loop Resistance (Vs-18) x 50 Response Time 10 ms Mounting Effects 0.15% FS (.25% FS for 1.5 Tri-Clover) Mechanical Configuration Pressure Port 1.5 Wetted Parts 316 Stainless Steel 1/2 NPT Conduit Fitting and Strain Relief with 15 ft. Cable Enclosure Stainless Steel Vibration 10g Peak Sinusoidal, 50 to 1000 Hz Acceleration 10g Shock 50g Approvals Meets 3-A Sanitary Standards Weight 8 oz ORDERING Series TDG07 2 Triclover 10 Proof Burst 1.5 Triclover 10 Proof Burst Pressure Port 1 Cable Length psig 0-2-psig 0-5psig 0-10psig 0-15psig 0-30psig 0-60psig 0-100psig 0-150psig Vac to 15psig 50psig 100psig 150psig 150psig 150psig 150psig 180psig 200psig 225psig 150psig 100psig 150psig 200psig 200psig 200psig 300psig 400psig 400psig 400psig 300psig 30psig 60psig 100psig 300psig 500psig 1000psig Vac to 15psig Vac to 45psig = 1.5 Triclover 2 = 2 Triclover 15ft (standard) 20ft 25ft 1 = 0.1% 2 = 0.2% (standard) = Consult factory for further options. Specificationsmay change without notice. The informationwe supply is believed to be accurate and r eliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Directweb site, it is up to the customer to determine the suitability of the product in the application. REV: 0705

32 Introducing the TDG series Intrinsically Safe Industrial Pressure Transducers. (When used with approved barrier) SERIES: TDG01/03/04 I.S. FEATURES Gauge, Absolute, Vacuum and Compund Pressure Models Available Submersible, General Purpose and Wash Down Enclosures High Stability Achieved by CVD Sensoring Element Voltage and Current Models Custom pressure ranges available ASIC Technology, No Zero/Span Potentiometers DESCRIPTION The TDG series features stability and accuracy in a variety of enclosure options. The TDG series extends the packaging options via an all welded stainless steel back end for demanding submersible and industrial applications. The TDG series feature proven CVD sensing technology, an ASIC (amplified units), and modular packaging to provide a sensor line that can easily accommodate specials while not sacrificing high performance. ELECTRICAL CONNECTIONS Power Supply Requirements Voltage Units: 1.5 vdc 0ver Max (voltage outputs) Current Units: 7-35vdc for 4-20 ma Voltage Units with conduit/cable Red= +Power Black= -Power White= Voltage Units with Din 9.4 mini DIN Current Units with conduit/cable Red= +Power Black= Pin 1 +Power Supply Current Units with Din Pin 1 +Power Supply Pin 2 Pin 3 N/C Pin 4 Gr Dimensions In Inches And Are Reference Only. MATING CONNECTOR P/N: TD4P9-00 Mating Connector (ordered separately) P/N: TD4P Meter Molded Cable Assembly Other Lengths Available 3/4 Hex

33 SPECIFICATIONS Input Vacuum to 400 bar (6000 psi) Proof Pressure 2 x / 4 x Full Scale (FS) (1.5 x Fs for 400 bar, >= 5000 psi) Burst Pressure >35 x FS <= 6 bar (100 psi); >20 x FS >=60 bar (1000 psi); >5 x FS <= 400 bar (6000 psi) Fatigue Life Designed for more than 100 million FS cycles Performance Long Term Drift 0.2% FS/year (non-cumulative) 0.25% / 0.5% FS typical (optional 0.15%) Thermal Error 1.5% FS typical (optional 1% FS) Compensated Temperatures -20 to 80 C (-5 to 180 F) Operating Temperatures -40 to 125 C (-22 to 260 F) for the mini DIN -20 to 80 C (-5 to 180 F) for the Conduit/Cable Amplified units >100 C maximum 24 Vdc supply Zero Tolerance Span Tolerance Response Time Mechanical Configuration Pressure Port Wetted Parts Enclosure Vibration Acceleration Shock Approvals Weight 1% of span 1% of span 0.5 ms See ordering chart 17-4 PH Stainless Steel See ordering chart 316 ss, 17-4 PH ss IP65 for the mini DIN 70g, peak to peak sinusoidal, 5 to 2000 Hz (Random Vibration: 20 to 2000 ı 20g Peak per MIL-STD.-810E Method 514.4) 100g steady acceleration in any direction 0.032% FS/g for 1 bar (15 psi) range decreasing logarithmically to % FS/g for 400 bar (6000 psi) range. 20g, 11 ms, per MIL-STD.-810E Method Procedure I (Intrinsically safe) class 1, division 1 & 2, groups C & D (check electrical connection code to determine division) Approx. 100 grams (additional cable; 75 g/m) ORDERING Series TDG03 TDG03= 2X Over Pressure TDG01= 4X Over Pressure TDG04 = when O is Selected D Pressure Type G B= 4-20ma G = Gauge H= 1-5 vdc K= vdc D= 0-10 vdc C= 0-5 vdc all voltage outputs are 3 wire non-ratiometric Proper Barriers must be used with this product. = Consult factory for further options vac vac vac vac vac vac vac Pressure Port 03 03= 1/4 NPT Male 09= 7/16 x 20 SAE #4 (J1926-2) 01= 1/8 NPT MALE OR Pressure Type A= Absolute D D= 4 pin Mini 9.4 DIN (class 1, div 1) O= 1/2 npt male conduit w/ 1 meter cable (class 1, div 2) = 0.5% 2= 0.25% 1= 0.15% I.S. S S= intrinsically safe REV: 0605

34 T DG Pressure T ransducer Wiring Specifications Voltage unit see ordering chart Supply Voltage (Vs 1.5 VDC above span to 35 6 ma Supply Voltage Sensitivit 0.01% FS/Volt Min. Load Resistanc (FS output / 2) Kohms Current Consumption approx 6 ma at 7.5V output Current unit 4-20 ma (2 wire) Supply Voltage (Vs 24 VDC, (7-35 VDC) Supply Voltage Sensitivit 0.01% FS/Volt Max. Loop Resistanc (Vs-7) x 50 ohms Electromagnetic Capability Meets the requirement for CE marking of EN for emissions and EN for susceptibility. Test Data: EN Electrostatic Discharge. 8kV air discharge, 4kV contact discharge. Unit survived. ENV50140 Radiated RF Susceptibility. 10V/m, 80MHz- 1GHz, 1kHz mod. Maximum recorded output error was <±1% ENV50204 Radiated RF Susceptibility to Mobile Telephones. 10V/m, 900MHz. Maximum recorded output error was <±1%. EN Fast Burst Transient. 2kV, 5/50ns, 5kHz for 1 minute. Unit survived. ENV50141 Conducted RF Susceptibility. 10Vms, 1kHz mod, 150kHz - 80MHz. Maximum recorded output error was <±1% Connection Code Voltage units Current units(4-20ma) IN+ COM OUT+ EARTH (+) ( ) EARTH DIN PIN Bayonet PIN A C B E A B E cable R BK W DRAIN R BK DRAIN IP 67 cable R BK W DRAIN R BK DRAIN Immersible R W Y DRAIN R BL DRAIN 8-4 Bayonet PIN A C B D A B D cable R BK W DRAIN R BK DRAIN conduit & cable R BK W DRAIN R BK DRAIN Cable Legend R = Red BL = Blue BK = Black W = White Y = Yellow POWER SUPPLY (-) (+) (-) (+) IN (+) COMMON OUT(+) VOLTAGE OUTPUT TRANSDUCER READOUT POWER SUPPLY (-) (+) (-) (+) + (-) CURRENT OUTPUT TRANSDUCER READOUT G-4 Questions? Call T ransducers Direct T ech Support

35 Introducing the TDM52 4 Times Over Pressure, OEM Pressure Transducer for Injection Molding Machines SERIES: TDM52 FEATURES High Digitally Compensated One-piece Stainless Steel Construction Ranges up to 5000 PSI or 350 BAR Amplified s Wide Operating Temperature Range Direct Replacement For Competitive Units DESCRIPTION The TDM52 Series (4 x over pressure) pressure transducer sets a new price performance standard for low cost, high volume, commercial and industrial applications. This series is suitable for measurement of liquid or gas pressure, even for difficult media such as contaminated water, steam, and mildly corrosive fluids or gases. The transducer pressure cavity is machined from a solid piece of 17-4 PH stainless steel. The standard version includes a 1/4 NPT pipe thread allowing a leak-proof, all metal sealed system. There are no o -rings, welds or organics exposed to the pressure media. The durability is excellent. APPLICATIONS Pumps and Compressors Hydraulic/Pneumatic Systems Off Road/Mobile Equipment Energy and Water Management Injection Molding Machines Agriculture Equipment Train Braking Systems Transducers Direct proprietary Microfused technology, derived from demanding aerospace applications, employs micromachined silicon piezoresistive strain gages, fused with high temperature glass to a stainless steel diaphragm. This approach achieves media compatibility simply and elegantly providing an exceptionally stable sensor without the p-n junctions of conventional micromachined sensors. This product is geared to the OEM customer using medium to high volumes. The standard version is suitable for many applications, but the dedicated design team at our Transducer Engineering Center stands ready to provide a semi-custom design where the volume and application warrants. ELECTRICAL CONNECTIONS For Cables: Voltage s Current s Red= +Power Supply Red= +Power Supply Black= -Power Supply Black= - White= MATING CONNECTOR P/N: TD4P9-00 Mating Connector (ordered separately) P/N: TD4P Meter Molded Cable Assembly Other Lengths Available Dimensions In Inches And Are Reference Only.

36 SPECIFICATIONS Performance at 25 C (77 F): Pressure range 0-25, 50, 75, 100, 250, 500, 1000, 2500, 5000 PSI (0-3, 6, 7, 17, 35, 70, 175, 350 BAR), % of FS Span ± 0.5% BSL, max (per ISA S37.2) (combined linearity, hysterisis and repeatability) Media compatibility 17-4 PH stainless steel (optional 316L stainless) Pressure cycles 10 million, minimum Pressure overload 4 times rated pressure Burst pressure 4 times full scale or 20,000 PSI, whichever is less Long term stability (1 year) ± 0.25% FS Span (Typical) Electrical: Ratiometric Non-Ratiometric Supply voltage 4.75 to 5.25VDC 10-30VDC Supply current <10mA <25mA 0.5 to 4.5V, at 5V 1-5V, (3 wire) 4-20mA, (2 wire) vdc, (4 wire) Bandwidth DC to 1KHz (Typical) Load impedance > 100k Ohms for quoted performance for 4-20mA; 0.05(Vsupply-10)k Ohms (maximum) Standard connector options 6-pin Bendix, 9.4 Mini DIN Cable Out (Additional connectors available upon request in volume) ENVIRONMENTAL Operating temperature range -40 to 100 C (125 C available, consult factory) Compensated temperature range -20 to 85 C (125 C available, consult factory) Total error band < ± 1% of FS (75-10,000 PSI) (over compensated temperature range) < ± 1.5% of FS (25-50 PSI) Storage temperature range -45 to 100 C Shock 50g, 11msec half sine shock per MIL standard 202F, method 213B, condition A Vibration ±20g MIL-STD-810C, Procedure 514.2, Figure , curve L EMI/RFI Immunity EN EN (10V/M, MHz) EN (Effective July 1, 2001) Humidity 95% RH, condensing ORDERING Series TDM52 TDM52= 4X Over Pressure L Pressure Type G B= 4-20ma G = Gauge H= 1-5 vdc K= vdc (ratiometric) L= vdc (4-wire) O= 0-10 vdc (4-wire) 4000 psi Pressure Port 21 03= 1/4 NPT Male 09= 7/16 x 20 SAE #4 (J1926-2) 21= 7/16 x 20 (Extended Boss) D S= Six Pin Bendix D= 4 pin Mini 9.4 DIN C= Cable Cable Length 00 00= None 02= 2 feet 3 3= 0.5% = Consult factory for further options. REV: 2.10

37 SPECIFICATIONS 25 C (77 F) ±1.0% BFSL (optional 0.5%, 0.2% and 0.1%) Stability <±0.2% FS/year, typical Over pressure protection 2X Rated Pressure Burst Pressure 2.5X minimum Pressure Cycles >50 Million Environmental Data Operating temp -20 to +80 C (-40 to +176 F) Storage temp -50 to +125 C (-60 to +250 F) Compensated range 0 to 55 C (+32 to +130 F) Electrical Data Excitation 9-29 Vdc / 4-20mA 0utput Electrical rating IEC Ex ia IIC T5 Nema 6P Loop 24 Vdc: 500 Ohm Zero offset <±1.0% of FS Span tolerance <±1.0% of FS Physical data Sensor wetted material 316SS (TDT02 & 03), Titanium (TDT01) Body material 316SS (TDT02 & 03), Titanium (TDT01) Cable pull strength 200 lb. Pressure connection Flush diaphragm with debris stand-off (TDT03), Bullet-Nose (TDT01 & 02) Molded, vented submersible cable (Polyethylene outer jacket) ORDERING Series TDT01/02/03 TDT01 = Titanium TDT02 = 316 stainless steel TDT03 = 316 stainless steel / stand off B B= 4-20mA Pressure Type G G = Gauge = 0-5 psi 0010= 0-10 psi 0015= 0-15 psi Pressure Connection 00 00= Nose Cone C= Cable (TDT01 & 02) 30= Debris Avoidance Stand-Off (TDT03) C Cable Length 50 25= 25 ft 50= 50 ft 75= 75 ft 100= 100 ft 4 4= 1% (standard) 3= 0.5% 2= 0.25% 0= 0.1% = Consult factory for further options. Transducers Direct is a registered trademark of Transducers Direct, LLC.) eliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Directweb site, it is up to the customer to determine the suitability of the product in the application. REV: 11.07

38 Introducing the TDTS30 Series Temperature Switch. SERIES: TDTS30 FEATURES Bi - Metal Immersion Temperature Switch Factory Preset Temperature Nema 4, 13 Direct Action Contacts Minimum Hysteresis Gold Di used, Fine Silver Contacts For Use In Low Voltage / Low Current Applications DIMENSIONS SPECIFICATIONS Set Point Range F Set Point Tolerance ±5 F Max Temperature -65 F to 325 F Current Rating 3 AMP at 240 VAC 2 AMP at 24 VDC (Resistive) Probe Length 1.5, 1 or 0.5 (1 standard) Media Connection See Ordering Code Circuit Form SPST-NO or SPST-NC 6 Wire Leads Maximum External Pressure 5000 PSI ORDERING Dimensions In Inches And Are Reference Only. Series TDTS30 Probe Length 1 Media Connection 3 Circuit Type A Fixed Set Point 100 Setting Direction R W TDTS30 1 = 1.0 (Stock) 2 = = = 3/8 NPT 3 = 1/4 NPT 6 = 1/2 NPT 7 = M16x1.5 A= SPST-NO B= SPST-NC 40 F F (In 10º increm ents) R= Rising F= Falling W= 6 Wire Leads B= 1 4 Blade Connection T= Screw Terminals WP=Weather Pack *Contact factor cationsmay change without notice. The informationwe supply is believed to be accurate and r eliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Transducers Directweb site, it is up to the customer to determine the suitability of the product in the application. REV: 10.09