G 1/4 A DIN 3852 (bar version) ±0.5 %FS max

Transcription

1 Pressure Transducers HDA 00 & 700 About HDA 00 & 700 Pressure Transducers: Series HDA 000 transducers are compact, heavy-duty, pressure instruments designed for both OEM industrial and off-road applications where accuracy, repeatability, and stability can not be compromised. This series utilizes a shock resistant thin film sensor as the pressure to electrical conversion element. Thin film technology is used because it maintains its accuracy over a wide temperature range, extreme dynamic conditions, and hostile environments. When combined with a proprietary amplification circuit, its typical accuracy class is ± 0.5% or ± 0.5% BFSL. Wetted metal parts are corrosion resistant stainless steel. It is available in eight pressure ranges from 50 psi up to 9000 psi. It is protected from extreme EMI emissions and can be applied in critical closed loop operating systems. It carries the mark and is designed and manufactured to ISO 900 Quality System requirements. Technical Details: Input Data HDA 00 HDA 700 Measuring ranges 50, 750, 000, 500, 000, 5000, 6000, 9000 psi 50, 750, 000, 500, 000, 5000, 6000, 9000 psi 6, 60, 00, 50, 6, 6, 60, 00, 00, 600 bar 50, 00, 600 bar Overload pressure 50% FS, 00% FS, maximal 000 psi (900 bar) maximal 000 psi (900 bar) Burst pressure 00% FS SAE 6 9/6-8 UNFA male G / A DIN 85 (bar version) Tightening torque approx. 5 lb-ft (0 Nm) Parts in contact with media Stainless steel, FPM seal Output Data Accuracy (B.F.S.L) including linearity, hysteresis, and repeatability ±0.5 %FS max ±0.5 %FS max ±0.0085%FS/ F typ. ±0.005%FS/ F typ. zero point ±0.0%FS/ F max. ±0.0085%FS/ F max. ±0.0085%FS/ F typ. ±0.005%FS/ F typ. over range ±0.0%FS/ F max. ±0.0085%FS/ F max. Rise time approx. ms Long-term drift ±0.%FS typ. / year ±0.%FS typ. / year Ambient Conditions Nominal temperature range to 58 F (0 to 70 C) - to 85 F (-5 to 85 C) Operating temperature range - to 85 F (-5 to 85 C) -0 to 85 F (-0 to 85 C) Storage temperature range -0 to F (-0 to 00 C) Fluid temperature range -0 to F (-0 to 00 C) mark EN 5008-, EN EN 5008-, EN Vibration resistance to IEC at 0 to 500Hz 0g (96. m/s ) Safety type to DIN 0050 IP 65 (DIN 650 and M8x connectors) IP 67 (ZBE 06 molded cable) Other data Supply voltage -conductor 0 to 0 VDC Supply voltage -conductor to 0 VDC Residual ripple supply voltage 5% Current consumption -conductor approx. 5 ma Reverse polarity protection of the supply voltage, excess voltage, standard override and short circuit protection Life expectancy > 0 million load cycles 0 to 00%FS Weight approx. 5 g Special models on request. Applications: Approvals: Electronics Catalog

2 Model Code: Series HDA = 000 series Pressure Transducer HDA X X X - X - XXXX Accuracy = 0.5% BFSL 7 = 0.5% BFSL = G / A DIN 85 (bar ranges only) 7 = SAE 6 9/6-8 UNFA male Electrical Connection = pole plug M8x (connector not included) 5 = DIN 650/ISO 00 plug, pole + ground (connector ZBE 0 included) 6 = Mx plug, -pole (connector not included) Output Signal A = conductor, -0 ma B = conductor, 0-0 VDC Pressure Range for mechanical connetion (7) for mechanical connetion () 050 = 50 psi (0 bar) 000 = 000 psi (07 bar) 006 = 6 bar (87 psi) 50 = 50 bar (65 psi) 0750 = 750 psi (5 bar) 5000 = 5000 psi (5 bar) 06 = 6 bar ( psi) 00 = 00 bar (5800 psi) 000 = 000 psi (69 bar) 6000 = 6000 psi ( bar) 060 = 60 bar (870 psi) 600 = 600 bar (8700 psi) 500 = 500 psi (0 bar) 9000 = 9000 psi (60 bar) 00 = 00 bar (50 psi) Modification Number 000 = Standard Note: Not all combinations are available. Circuit Connection: HDA XX-A Three-Conductor 0 to 0 VDC min = k HDA XX-B V signal Plug Connection: HDAXX use with ZBE 0 (see page 60) HDAXX5-A HDA XX6-A Dimensions:.6" (9.5 mm) ø.78" (5 mm) Three-Conductor 0 to 0 VDC min = k HDA XX5-B Three-Conductor 0 to 0 VDC min = k HDA XX6-B X ø.6" ( mm) V V signal HDA XX/XX, illustrated with ZBE 0 HDA XX5/XX5, illustrated with ZBE 0 signal HDAXX5 use with ZBE 0 or ZBE 0 (see page 60) HDAXX6 use with ZBE 06 (see page 60) HDA XX6/XX6, illustrated with ZBE 06.6 (9mm) ø.6" ( mm) SAE 6 Hex SW.06" (7mm)." (57mm).78" (5 mm) SAE 6 Hex SW.06" (7mm)." (57mm) Dimension X: with right angled plug ZBE 0.5" (08mm) Dimension X: with straight plug ZBE 0 5.0" (7mm).8" (0 mm) SAE 6 Hex SW.06" (7mm)." (57mm).0" (8mm) -877-GO HYDAC Electronics Catalog

3 Pressure Transducers HDA 00 & 00 About HDA 00 & 00 Low Pressure Transducers: The HDA 00 & 00 is similar in design to our HDA 00 series. This transducer utilizes a ceramic sensor element to provide our customers a low cost, low pressure sensor while maintaining accuracy, repeatability, and stability. The body is stainless steel. Pressure ranges from 0 to 5 psi up to 500 psi are available. A number of port sizes and electrical connection combinations make this an attractive and affordable solution to your low pressure needs. These transducers are ideal for your pneumatic applications. Technical Details: Input Data Measurement range 0 to 5, 50 psi (A) 0 to 5, 0, 50, 00, 50, 50, 500 psi (G) Overload pressure 00%FS Burst pressure 00%FS Mechanical connection / -8 NPT male Parts in contact with media Ceramic, FPM or EPDM seal Output data Accuracy (B.F.S.L) including linearity, hysteresis, and repeatability ±0.5 %FS max. ±0.0%/ F typ. Zero point ±0.07%/ F max. ±0.0%/ F typ. over range ±0.07%/ F max. Rise time approx. ms Long-term drift ±0.%FStyp. / year Ambient Conditions Nominal temperature range to 76 F (0 to 80 C) Operating temperature range - to 85 F (-5 to 85 C) Storage temperature range -0 to F (-0 to 00 C) Fluid temperature range -0 to F (-0 to 00 C) mark EN 5008-, EN EN 5008-, EN Vibration resistance to IEC at 0 to 500Hz 0 g (96, m/s ) Safety type to DIN 0050 IP 65 (DIN 650 connector) IP 67 (ZBE 06 molded cable) Other Data Supply voltage -conductor 0 to 0 V DC Supply voltage -conductor to 0 V DC Residual ripple supply voltage 5 % Current consumption -conductor approx. 5 ma Reverse polarity protection of the supply voltage, excess voltage, override and standard short circuit protection Life expectancy >0 million load cycles (0 to 00%FS) Weight approx. 5 g Applications: Approvals: 5 Electronics Catalog

4 Model Code: HDA X X X - X - XXXX X Series HDA = 000 series Pressure Transducer Accuracy = Absolute (ceramic) 0.5% BFSL = Gauge (ceramic) 0.5% BFSL 8 = / - 8 NPT male thread Electrical Connection 5 = DIN 650/ISO 00 plug, pole + ground (connector ZBE 0 included) 6 = Mx plug, -pole (connector not included) Output Signal A = conductor, -0 ma B = conductor, 0-0 VDC Pressure Range Absolute Gauge 005 = 0 to 5 psi 005 = 0 to 5 psi 0050 = 0 to 50 psi 000 = 0 to 0 psi 0050 = 0 to 50 psi 000 = 0 to 00 psi 050 = 0 to 50 psi 050 = 0 to 50 psi 0500 = 0 to 500 psi Modification Number 000 = Standard Sealing Material (in contact with media) F = FPM seal (to be used for example with hydraulic fluid) E = EPDM seal (to be used for example with refrigerant coolant or fluids containing ammonia) Material for / Housing (in contact with media) = Stainless Steel Circuit Connection: Plug Connection: HDA XX5 use with ZBE 0 (see page 60) HDA X85-A HDA X86-A HDA XX6 use with ZBE 06 (see page 60) Three-Conductor 0 to 0 VDC min = k HDA X85-B Dimensions: V.8" (97.5mm) signal Three-Conductor 0 to 0 VDC min = k HDA X86-B ø.6" ( mm) V signal.8" (96.5mm) ø.6" ( mm) / NPT Hex SW (7mm).06"." (6.5mm).78" (5 mm) / NPT Hex SW (7mm).06"." (6.5mm).0" (8mm) -877-GO HYDAC Electronics Catalog 6

5 Pressure Transducers HDA 7000 About HDA 7000 OEM Pressure Transducers: The pressure transducer series HDA 7000 combines excellent technical specifications with a very compact design. The HDA 7000 was specifically developed for severe applications e.g. mobile applications. A thin film sensor cell is the basis for a robust, long-life pressure transmitter. Various pressure ranges between 0 to 50 psi and 0 to 9000 psi facilitate adaptation to the particular application. For integration into modern controls (e.g. with PLC) different analog output signals, including to 0 ma or 0 to 5 V, are available on the standard version. Ratio-metric output signals are also available on request. Technical Details: Input Data Measuring ranges Overload pressure Burst pressure Tightening torque G /, SAE 6 SAE Parts in contact with media Output Data Accuracy (B.F.S.L) including linearity, hysteresis, and repeatability zero point over range Rise time Long-term drift Ambient Conditions Nominal temperature range Operating temperature range Storage temperature range Fluid temperature range mark Vibration resistance to IEC at 0 to 500Hz Safety type to DIN 0050 Other data Reverse polarity protection of the supply voltage, excess voltage, override and short circuit protection Life expectancy Weight (with M connector) 0 to 500, 750, 000, 500, 000, 5000, 6000, 9000 psi 50% FS, maximal 000 psi 00% FS SAE 6 9/6-8 UNFA male, G / A DIN 85, SAE, / NPT approx. 5 lb-ft (0 Nm) approx. lb-ft (5 Nm) Stainless steel, FPM seal ±0.5 %FS ±0.0085%FS/ F ±0.07%FS/ F ±0.0085%FS/ F ±0.07%FS/ F approx. ms ±0.%FS typ. / year - to 85 F (-5 to 85 C) -0 to 85 F (-0 to 85 C) -0 to F (-0 to 00 C) -0 to F (-0 to 00 C) EN 5008-, EN EN 5008-, EN g (96. m/s ) IP 67 (w/ ZBE 06 molded cable or flying lead) standard 0 million load cycles 0 to 00%FS approx. 8 g Applications: Approvals: 7 Electronics Catalog

6 Model Code: Series HDA 7 = 7000 series Pressure Transducer Accuracy = 0.5% BFSL = G / A DIN 85 7 = SAE 6 9/6-8 UNFA male Electrical Connection 0 = flying leads 6 = M connector X = customer specified connector Output Signal A = conductor, -0 ma B = conductor, 0- G = conductor, (please specify output voltage) Pressure Range 0500 = 500 psi ( bar) 000 = 000 psi (07 bar) 0750 = 750 psi (5 bar) 5000 = 5000 psi (5 bar) 000 = 000 psi (69 bar) 6000 = 6000 psi ( bar) 500 = 500 psi (0 bar) 9000 = 9000 psi (60 bar) Modification Number 000 = Standard * Specifications must be submitted by customer. HDA 7 X X - X - XXXX Circuit Connection: Flying Leads: Plug Connection: HDA 7XX6 use with ZBE 06 (see page 60) to 0 ma brown black 0 to 5 V to 6 V 0.5 to.5 V 0 to 0 V red brown black V signal Mx: to 0 ma 0 to 5 V to 6 V 0.5 to.5 V 0 to 0 V Dimensions:.98" (5.5mm) V signal SAE-6 9/6-8 UNF.067 (5.5mm) 0.078" (mm) essur Prconnection DIN85 ø 0.78" (8.5mm) 0.7" (8.9mm) ø 0.78" (8.5mm) Mx G /A ø 0.8.7" (mm) hex-sw " (0.0mm) hex-sw078 6kt-SW9-877-GO HYDAC Electronics Catalog 8

7 Pressure Transducers HDA 700 & 800 About HDA 700 & 800 Pressure Transducers: The HDA 000 family of transducers is designed to provide exceptional durability and accuracy in demanding industrial and mobile applications. They are used to convert hydraulic or pneumatic pressure into an electrical output signal linearly proportional to the input pressure. The signals can be sent to most commonly used processors and controllers, including PLC's, computers, recorders, and digital displays. Technical Details: Input Data HDA 700 HDA 800 Measuring ranges 6, 6, 60, 00, 6, 6, 60, 00, 50, 00, 600 bar 50, 00, 600 bar Overload pressure 00% FS, maximum 900 bar 00% FS, maximum 900 bar Burst pressure 00% FS 00% FS G / A DIN 85 SAE 6 9/6-8 UNFA male G / A DIN 85 SAE 6 9/6-8 UNFA male (with adapter) (with adapter) Tightening torque 5 lb-ft (0 Nm) 5 lb-ft (0 Nm) Parts in contact with media Stainless steel, FPM seal Stainless steel, FPM seal Output Data Accuracy (B.F.S.L) including linearity, hysteresis, and repeatability ±0.5 %FS max. ±0.5 %FS max. ±0.005%FS/ F typ. ±0.00%FS/ F typ. zero point ±0.0085%FS/ F max. ±0.006%FS/ F max. ±0.005%FS/ F typ. ±0.00%FS/ F typ. over range ±0.0085%FS/ F max. ±0.006%FS/ F max. Rise time approx. 0.5 ms approx. 0.5 ms Long-term drift ±0.%FS typ. / year ±0.%FS typ. / year Ambient Conditions Nominal temperature range - to +85 F (-5 to +85 C) - to +85 F (-5 to +85 C) Operating temperature range -0 to +85 F (-0 to +85 C) -0 to +85 F (-0 to +85 C) Storage temperature range -0 to + F (-0 to +00 C) -0 to + F (-0 to +00 C) Fluid temperature range -0 to + F (-0 to +00 C) -0 to + F (-0 to +00 C) mark EN 5008-, EN EN 5008-, EN EN 5008-, EN EN 5008-, EN Vibration resistance to IEC at 0 to 500Hz 0g (96. m/s ) 0g (96. m/s ) Safety type to DIN 0050 IP 65 IP 65 Other data Supply voltage -conductor 0 to 0 VDC 0 to 0 VDC Supply voltage -conductor to 0 VDC to 0 VDC Residual ripple supply voltage 5% 5% Current consumption -conductor approx. 5 ma approx. 5 ma Reverse polarity protection of the supply voltage, excess voltage, standard standard override and short circuit protection Life expectancy 0 million load cycles, 0 million load cycles, 0 to 00%FS 0 to 00%FS Weight approx. 80 g approx. 80 g Special models on request. Applications: Approvals: 9 Electronics Catalog

8 Model Code: HDA X X X - X - XXX Series HDA = 000 series Pressure Transducer Accuracy 7 = 0.5% B.F.S.L. 8 = 0.5% B.F.S.L. = G / A DIN 85 7 = SAE 6 9/6-8 UNFA male supplied with adapter* Electrical Connection = pole plug, M8x (connector not included) 5 = DIN650/ISO00 plug, pole + ground (connector ZBE 0 included) Output Signal A = conductor, -0 ma B = conductor, 0-0 VDC E = conductor, 0-0 ma, sourcing Pressure Range 006 = 87 psi (6 bar)* 50 = 65 psi (50 bar)* 06 = psi (6 bar)* 00 = 5800 psi (00 bar)* 060 = 870 psi (60 bar)* 600 = 8700 psi (600 bar)* 00 = 50 psi (00 bar)* Modification Number 000 = Standard * Adapter is included to convert G/ Male to SAE-6 Male connection on some models ** Some model codes may no longer be available. Contact product management for crossovers to HDA 000 series. Circuit Connection: Two Conductor Output: Max. Load = Supply - (Ω) 0.0 Amp HDA-XX-A Free Free + Supply 0 to Three Conductor Output: Min. Load = k (Ω) HDA-XX-B Free V Signal 0 to + Supply to HDA-XX5-A HDA-XX5-B Three Conductor Output: Max. Load = Supply - 7V (Ω) 0.0 Amp Free V + Supply + Supply Signal 0 to Plug Connection: HDA XX5 use with ZBE 0 (see page 60) HDA XX use with ZBE 0 or ZBE 0 (see page 60) + Supply to + Supply HDA-XX-E Free Signal 0 to 0mA HDA-XX5-E Signal 0 to 0mA Dimensions: ø.06" (7 mm)." ( mm).06" Hex between flats G /.0" (8 mm) 0.7" ( mm) 0." (8 mm)." (8 mm).6" ( mm) -877-GO HYDAC Electronics Catalog 0

9 Specialty Pressure Transducers HDA CAN Bus About HDA CAN Bus Pressure Transducers: HYDAC has developed the HDA 000 CAN-bus sensor to meet the needs of the marketplace for a field-bus sensor. There are several field-bus systems on the market designed for specific industries. One of the most known in the hydraulic industry is the CAN-bus. The purpose of CAN-bus is to eliminate the need for heavy cabling trees, particularly in the automotive and process industries. The HDA 000 CAN-Bus sensors are interfaced by a pair of twisted wires which enables a CAN system to receive, dispatch and monitor information from hydraulic systems. CAN-bus is a relatively simple and uncomplicated system. In the hydraulic field there are applications for many mobile machine manufacturers such as excavators and tractors. Each CAN-bus sensor is custom designed for every OEM to meet their individual system needs. Technical Details: Input Data Measuring range 500, 000, 500, 000, 5000, 6000, 9000 psi 0, 00, 50, 00, 600 bar Overload range 00% FS max. 000 psi (900 bar) Burst pressure 00% FS Thread connection G / A DIN 85 SAE 6 9/6-8 UNF A Mounting torque 0 Nm Parts in contact with media Stainless-steel, FPM-seal Output data Accuracy (B.F.S.L) including linearity, hysteresis, and repeatability ±0.5 %FS ±0.005%FS/ F zero point ±0.0085%FS/ F ±0.005%FS/ F over range ±0.0085%FS/ F Rise time approx. ms Long-term drift ±0.%FS typ. / year Ambient Conditions Nominal temperature range - to 85 F (-5 to 85 C) Operating temperature range -0 to 85 F (-0 to 85 C) Storage temperature range -0 to F (-0 to 00 C) Fluid temperature range -0 to F (-0 to 00 C) mark EN , EN EN , EN Vibration resistance acc. 0 g (96. m/s ) IEC at Hz Type of protection acc.din 0050 IP 67 (ZBE 06 molded cable) Other Data Supply voltage 0 to 5 VDC Residual ripple supply voltage 5 % Current consumption 5 ma Reverse polarity protection of supply voltage, excess voltage, standard override and short circuit protection Type of electric connection Mx Pin : PE, shield acc. CIA-DR-0- Pin : +Vb Pin : 0 V Pin : CANH Pin 5: CANL Life expectancy >0 Mio. cycles (0 to 00 % FS) Weight ca. 50 g Applications: Approvals: Electronics Catalog

10 What Are Field-Bus Systems? A field-bus system is a data network with the objective to receive data from a production process, exchange data between devices or machines, control steps or processes in production. Data transmission happens serially with digital signals (equivalent to Internet data transmission.) The most basic design of such a data network is a -wire cable with various individual sensors (e.g. Pressure transmitters), actors (e.g. solenoid valves), controllers, periphery units, and control units (e.g. PLC, industrial PCs) connected at any point. BUS participants need a suitable interface, which transfers flow of data. Each individual component gets its own address. Structure of a Bus System: Bus master e.g. PLC Node Node Node Node 0 Node e.g. pressure transmitter e.g. valve e.g. temperature sensor Remarks: Communication of process data is performed by means of every individual sensor, component, and so on, being connected via it s own wiring to high layer control. Advantages: Easy wiring with clear reduction of cabling (best case: only two cables) Clear structure Diagnostic functions, connected units may be checked on functionality All system functions are available in high layer control at any time High level of transmission safety, information may be checked on validity through multiple transmissions Easy to be enlarged, since at any place of network a unit may be added Easy implementation into higher leveled systems: - connection to other bus system - distance diagnostic systems - service units -877-GO HYDAC Electronics Catalog

11 Specialty Pressure Transducers HDA 00 & Shipbuilding and Offshore About HDA 00 Pressure Transducers: This pressure transmitter, which has been specially developed for shipbuilding and offshore applications, is based on a very robust and accurate sensor cell with a thin film strain gauge on a stainless steel membrane. All parts in contact with the fluid are in stainless steel and are welded together. Since no seals are required in the sensor chamber, leakage is eliminated. The to 0 ma output signal in two conductor technic enables connection to the relevant evaluation electronics. Since accuracy varies markedly with the temperature of the fluid being measured, this instrument offers outstanding characteristics in this respect. Areas of application are pressure monitoring on marine transmissions, diesel engines, pumps and general hydraulic and pneumatic systems. Technical Details: Input Data HDA 00 HDA 700 Measuring ranges 6, 60, 00, 6, 6, 60, 00, 50, 00, 600 bar 50, 00, 600 bar Overload pressure 00% FS, maximal 900 bar Burst pressure 00% FS G / A DIN 85 Tightening torque approx. 5 lb-ft (0 Nm) Parts in contact with media Stainless steel, FPM seal Output Data Accuracy (B.F.S.L) including linearity, hysteresis, and repeatability ±0.5%FS ±0.5%FS ±0.0085%FS/ F typ. ±0.005%FS/ F typ. zero point ±0.0%FS/ F max. ±0.0085%FS/ F max. ±0.0085%FS/ F typ. ±0.005%FS/ F typ. over range ±0.0%FS/ F max. ±0.0085%FS/ F max. Rise time approx. ms Long-term drift ±0.%FS typ. / year Ambient Conditions Nominal temperature range to 58 F (0 to 70 C) - to 85 F (-5 to 85 C) Operating temperature range - to 85 F (-5 to 85 C) -0 to 85 F (-0 to 85 C) Storage temperature range -0 to F (-0 to 00 C) Fluid temperature range -0 to F (-0 to 00 C) mark EN and EN EN and EN Vibration resistance to 5 to 5 Hz:. mm IEC at 0 to 500Hz 5 to 00 Hz: g Safety type to DIN 0050 IP 65 Other Data Supply voltage 0 to 0 V Residual ripple supply voltage 5% Current consumption -conductor approx. 5 ma Reverse polarity protection of the supply voltage, excess voltage, available override and short circuit protection Life expectancy > 0 million load cycles 0 to 00%FS Weight approx. 5 g Applications: Approvals: American Bureau of Shipping No.: 00-ES 9976-X Lloyds Register of Shipping No.: 00/009 Det Norske Veritas No.: A-77 (89.0) Germanischer Lloyd No.: HH Bureau Veritas No.: 0 /A0 BV Electronics Catalog

12 Model Code: HDA X 5 - A - XXX - S00 Series HDA = 000 series Pressure Transducer for Shipbuilding & Offshore Accuracy = 0.5% B.F.S.L. 7 = 0.5% B.F.S.L. = G / A DIN 85 7 = SAE-6 9/6-8 UNFA male (using adapter) 8 = / -8 NPT male thread (using adapter) Electrical Connection 5 = DIN 650/ISO 00 plug, pole + ground (connector ZBE 0 included) Signal Technology A = -conductor, to 0 ma Measuring Ranges 006 = 6 bar (HDA 700 only) 06 = 6 bar 060 = 60 bar 00 = 00 bar 50 = 50 bar 00 = 00 bar 600 = 600 bar Modification Number S00 = standard Note: On units with a different modification number, please read the label or the technical amendment details supplied with the unit. All details are subject to technical modifications. Circuit Connection: -conductor to 0 ma Plug Connection: HDA X5 use with ZBE 0 (see page 60) HDAX5-A Free max. = UB - 0 V [Ω] 0.0 A Dimensions: 0.08" (mm) ø.06" (7mm) ø.8" (5mm)." (mm) Hex SW7 ø 0.7" G / A (8.9mm).97" (50mm) 0.7" (mm)." (8mm) -877-GO HYDAC Electronics Catalog

13 Specialty Pressure Transducers HDA Hazardous Locations - Class, Division / About HDA 700 Pressure Transducers: The pressure transducer series HDA 700 is available in a version for measuring pressure in hazardous locations. The HDA 700 family of transducers is designed to provide exceptional durability and accuracy in demanding industrial and process applications. They are used to convert hydraulic or pneumatic pressure into an electrical output signal linearly proportional to the input pressure. The signals can be sent to most commonly used processors and controllers, including PLC s, computers, recorders, and digital displays. The pressure measured by the sensor is converted to a proportional, analog to 0 ma output signal. The signals can be sent to most commonly used processors and controllers, including PLC's, computers, recorders, and digital displays. Technical Details: Input Data Measuring ranges 0 to 00, 50, 00, 00, 500, 600, 750, 000, 500, 000, Overload pressure Burst pressure Standard Mechanical Ports Tightening torque 5000, 6000, 9000, 0000 psi 00% FS, max. (except,000 psi for 9000 psi / 6,000 psi for 0,000 psi) 00% FS, max. 9,000psi SAE 6 9/6-8 UNFA male / -8 NPT male thread / -8 NPT female thread approx. 5 lb-ft (0 Nm) (standard models only) Stainless steel, FPM seal Parts in contact with media Output Data Accuracy (B.F.S.L) including linearity, hysteresis, and repeatability ±0.5 %FS max ±0.005%FS/ F typ. zero point ±0.0085%FS/ F max. ±0.005%FS/ F typ. over range ±0.0085%FS/ F max. Rise time approx. 0.5 ms Long-term drift ±0.%FS typ. / year Ambient Conditions Type of Protection Intrinsically Safe Nominal temperature range - to 0 F (-0 to 60 C) Operating temperature range - to 0 F (-0 to 60 C) Enclosures against dust non incendive Nominal temperature range - to 85 F (-0 to 85 C) Operating temperature range - to 85 F (-0 to 85 C) Storage temperature range (all) -0 to F (-0 to 00 C) Vibration resistance to IEC at 0 to 500Hz 96. m/s ( 0g) Safety type to DIN 0050 min. IP 65 (depending on connector) Other Data Supply voltage to 8 V (max W up to 6 V, max 0.8W for 6-8 V Maximum supply current 00 ma Capacitance of transducer nf Inductance of transducer 0H Residual ripple supply voltage 5% Reverse polarity protection of the supply voltage, and short standard circuit protection Life expectancy > 0 million load cycles 0 to 00%FS Weight approx. 80 g Some Models Conform consult factory to NACE MR-075 Applications: Approvals: Intrinsically Safe (all connector versions): Ex ia Class I, II, III; Division, Groups A, B, C, D, E, F, G T6 Class I, II, III; Division, Groups A, B, C, D, E, F, G T6 Ex ia IIc T6 Class, Zone 0, AEx IIC T6 Ambient temperature max. 60 C Non Incendive (connectors: 9; A only) Class I, II, III, Division, Groups A, B, C, D, F, G TA Ex na II T or Ex nl IIC T Class I, Zone, AEx na II T or AEx NL IIC T Ambient temperature max. 85 C Non Incendive (all connectors versions): Class I, II, III, Division, Groups A, B, C, D, F, G TA Ex nl IIC T Class I, Zone, AEx NL IIC T Ambient temperature max. 85 C 5 Electronics Catalog

14 Model Code: Series HDA = 000 series Pressure Transducer for Hazardous Locations Accuracy 7 = 0.5% BFSL = G / BSPP male 5 = SAE- female 7 = SAE-6 9/6-8 UNFA male 8 = / -8 NPT male thread 9 = G / BSPP female F = / -8 NPT female thread C = Autoclave female port Electrical Connection 5 = DIN 650 / ISO00 plug 9 = / NPT male conduit (wire leads) A = DIN 650 with / NPT female conduit Signal A = to 0mA Pressure Ranges 0 to 00, 50, 00, 00, 500, 600, 750, 000, 500, 000, 5000, 6000, 9000, 0,000 (psi) Approval U = HDA X X X - A - XXXX - U 00 (PSI) (XX inch) Modification Number used for pin connection, special calibration in pressure range Additional Declaration for PSI Wire Length 8 inch (longer wires on request) Bar ranges available upon request Model Codes Containing RED are non-standard items - Minimum quantities may apply Contact HYDAC for information and availability Circuit Connection: green + Supply DIN 650 / ISO00 plug: DIN 650 with / NPT female conduit: HDA7X9-A white green/yellow Dimensions: 0.9" (0mm) Hex SW.06 Hex SW0.78 / - NPT SAE 6 ø.6" (9mm) O-ring 0.68 x FPM (Viton) - 90 shore -877-GO HYDAC." (mm).08" (7mm) 8" (9mm) Electronics Catalog 6

15 Specialty Pressure Transducers HDA Intrinsically Safe with ATEX Approval About HDA 700 Pressure Transducers: The pressure transducer series HDA 700 is available in a version for intrinsically safe circuits for measuring pressure in hazardous applications. Like the industrial version of the HDA 700, the ATEX-version also has a very accurate, robust pressure sensor. With a basic accuracy of 0.5% BFSL and outstanding specifications regarding the temperature effect, this series is suitable for use in a wide range of applications. The pressure measured by the sensor is converted to a proportional, analog to 0 ma signal. The signals can be sent to most commonly used processors and controllers, including PLC's, computers, recorders, and digital displays. Technical Details: Input Data Measuring ranges (psi) 0 to 00, 50, 00, 00, 500, 600, 750, 000, 500, 000, 6000, 9000 psi 6, 6, 60, 00, 50, 00, 600 bar Overload pressure 00% FS, maximal,000 psi (900 bar) Burst pressure 00% FS Mechanical Ports G / (m) Tightening torque approx. 5 lb-ft (0 Nm) Parts in contact with media Stainless steel, FPM seal Output Data Accuracy (B.F.S.L) including linearity, hysteresis, and repeatability ±0.5% FS max ±0.005%FS/ F zero point ±0.0085%FS/ F ±0.005%FS/ F over range ±0.0085%FS/ F Rise time approx. 0.5 ms Long-term drift ±0.%FS typ. / year Ambient Conditions Nominal temperature range - to 0 F (-5 to 60 C) Operating temperature range -0 to 0 F (-0 to 60 C) Storage temperature range -0 to F (-0 to 00 C) Approval no. 0 ATEX E 57 X mark EN ///; EN5000; EN50000; EN508 Vibration resistance to IEC at 0 to 500Hz 96. m/s ( 0g) Safety type to DIN 0050 IP 65 Other Data Supply voltage to 8 V (max W up to 6 V, max 0.8W for 6-8 V Maximum supply current 00 ma Capacitance of transducer nf Inductance of transducer 0H Residual ripple supply voltage 5% Reverse polarity protection of the supply voltage, standard short circuit protection Life expectancy > 0 million load cycles 0 to 00%FS Weight approx. 80 g Applications: Equipment Group I Equipment Group Designated for use in the underground parts of mines aas well as those parts of surface installations of such endangered by firedamp and/or combustible gases M Approvals: Category Designated for use in the underground parts of mines dealing with all CH concentartions Equipment Group II Equipment Group Designated for use in areas in which explosive atmospheres caused by mixtures of air and gas vapors or mists or by air/dust mixtures are present continuosly, for long periods or frequently Category Use in zones 0,, possible Category Use in zones, possible / Category / Use in zones and possible Designated for use in zones 0 and, with the pressure sensor assuming the function of an isolating element IM EEx ia I II G EEx ia IIC T6 II / G EEx ia IIC T6 0 ATEX E 57 X 7 Electronics Catalog

16 Model Code: Series HDA = 000 series Intrinsically Safe Pressure Transducer Accuracy 7 = 0.5% BFSL HDA 7 X X - A - XXXX - A00 (PSI) XX inch = G / A DIN 85 7 = SAE-6 9/6-8 UNFA male (with adapter) 8 = / NPT male F = / -8 NPT female thread Electrical Connection = pole plug M8x plug (connector not included) 5 = DIN 650 / ISO00 plug, pole + ground (connector ZBE 0 included) 9 = / NPT male conduit - 8 or 7 leads Output Signal A = -conductor / to 0mA Pressure Ranges 0 to 00,50, 00, 00, 500, 600, 750, 000, 500, 000, 5000, 6000, 9000 psi 6, 6, 60, 00, 50, 00, 600 bar Modification Number A00 = IM EEX ia I, IIG EEX ia IIC T6, II/G EEx ia IIC T6 Additional Declaration for PSI Wire Length Model Codes Containing RED are non-standard items - Minimum quantities may apply Contact HYDAC for information and availability Circuit Connection: HDA7-A Free Free + Supply Plug Connection: HDA 7X5 use with ZBE 0 (see page 60) HDA 7X use with ZBE 0 or ZBE 0 (see page 60) HDA75-A Free + Supply / NPT male conduit: consult factory for availability Dimensions: ø.06" (7 mm)." ( mm).06" Hex between flats G /.0" (8 mm) 0.7" ( mm) 0." (8 mm). (8 mm).6" ( mm) -877-GO HYDAC Electronics Catalog 8

17 Specialty Pressure Transducers HDA Steel Works About HDA 800 Pressure Transducers: This high-precision pressure transducer has been specially developed and adapted for the sophisticated measurement demands of steelworks technology. The unit has a very robust sensor cell with a thin-film DMS which is applied to a stainless steel membrane. It s outstanding specifications with reference to temperature effect (temperature drift for zero point and range are at maximum ± 0.0 FS/ C each) and accuracy ( ± 0.5% FS typ.) makes it ideally suited for use in the harsh ambient conditions found in steelworks. The excellent EMC characteristics guarantee signal stability during the harshest high-frequency, electro-magnetic interference. Technical Details: Input Data Measuring ranges Overload pressure Burst pressure Tightening torque Parts in contact with media Output Data Accuracy (B.F.S.L) including linearity, hysteresis, and repeatability zero point over range Rise time Long-term drift Ambient Conditions Nominal temperature range Operating temperature range Storage temperature range Fluid temperature range 50 bar 900 bar 000 bar G/ A DIN 85, G/ A male SAE 6 9/6-8 UNFA male approx. 5 lb-ft (0 Nm) for G/ A approx. lb-ft (5 Nm) for G/ A Stainless steel, FPM seal (G/ A) NBR O-ring (G / A) ±0.5 %FS max. ±0.008%FS/ F typ. ±0.0056%FS/ F max. ±0.008%FS/ F typ. ±0.0056%FS/ F max..5 ms ±0.%FS typ. / year - to 85 F (-5 to 85 C) -0 to 85 F (-0 to 85 C) -0 to F (-0 to 00 C) -0 to F (-0 to 00 C) EN and EN mark EN and EN Vibration resistance to 5 g IEC at 0 to 500Hz Safety type to DIN 0050 IP 68 Other Data Supply voltage conductor - 0 to 0 V conductor - to 0 V Residual ripple supply voltage 5% Current consumption -conductor approx. 5 ma Reverse polarity protection of the supply voltage, excess voltage, standard override and short circuit protection Life expectancy 0 million load cycles, 0 to 00%FS Weight 0 g Applications: Approvals: Note: F.S. (Full Scale) = Relative to the full measuring range * = Other measuring ranges on request 9 Electronics Catalog

18 Model Code: Series HDA 8 = Pressure Transducer for Steel Works 0 = G / A male thread = G / A DIN 85 7 = SAE 6 9/6-8 UNFA male Electrical Connection 0 = flying lead 6m (Teflon cable, silicon-) Output Signal A = conductor, -0 ma E = conductor, 0-0 ma Pressure Range 50 = 50 bar (5075 psi) Modification Number (determined by manufacturer) HDA 8 X 0 - X Note: PSI pressures on request Contact HYDAC for availability Circuit Connection: conductor to 0 ma HDA8xx-A UB - 0 V max. = 0.0 A brown blue supply conductor 0 to 0 ma black brown HDA8xx-E blue max. = UB - 7 V 0.0 A supply Signal Plug Connection: A-Signal Brown: Blue: E-Signal Black: Brown: Blue: + Supply + Supply Signal Dimensions: cable gland pg 7 ø.8" (0mm) ø.06" (7mm) 0." (8mm) ø0.7" Hex (8.9mm) G/ A.7" (9.6mm) cable gland pg 7 ø.8" (0mm) ø.06" (7mm) 0." (8mm) ø.06" Hex G/ A.7" (6.9mm) (9.6mm) 6 m (fully extended cord length)." (8mm)." (05mm) 0.08" (mm) 6 m (fully extended cord length)." (8mm)." (05mm) 0." (mm) -877-GO HYDAC Electronics Catalog 0

19 Specialty Pressure Transducers HDA 80 - Submersible About HDA 80 Submersible Transducers: HYDAC's HDA 80 Series transmitter is a submersible pressure transducer suitable for liquid level and depth measurement in a variety of industrial and municipal level measurement applications. Its stainless steel sealed housing makes it suitable for immersion in most industrial liquids and oils as well as wastewater and seawater. Safety rated to IP 68, they are specifically designed to operate under the rigorous conditions encountered in liquid level measurement and control. A 0 foot vented polyurethane cable (other lengths available) provides an atmospheric pressure reference. Each transducer is shipped with a membrane barrier that prevents moisture from entering the cable vent tube. Technical Details: Input Data Measurement range Overload range Burst pressure Mechanical connection Tightening torque Parts in contact with media 5, 0, 5 psi 0, 0, 0 psi 0, 0, 60 psi / NPT male 0 Nm Stainless steel, ceramic seal: EPDM Output Data Output signal to 0 ma, -conductor Accuracy (calibrated at 68 F) ±0.5 %FS B.F.S.L Zero point (calibrated with pressure ±0. %FS ( ±0.05 ma) typ. port pointing downwards) ±0.6 %FS ( ±0.0 ma) max. zero ±0.0 %FS/ C typ. point in the range to 0 F ±0.0 %FS/ C max. (in the range 5 to 0 C) ±0.0 %FS/ C typ. span in the range to 0 F ±0.0 %FS/ C max. (in the range 5 to 0 C) Long term drift ±0.5 %FS typ. / year Ambient Conditions Operating temperature range - to 58 F (-5 to 70 C) Storage temperature range - to 58 F (-5 to 70 C) Fluid temperature range - to 58 F (-5 to 70 C) mark EN , EN EN , EN Safety type to DIN 0050 IP 68 Other Data Supply voltage 0 to 0 V Load resistance [Ω] max = Usupply - / 0,0 A Residual ripple supply voltage 5 % Electrical connection / Conduit with vented cable Tensile strength (transducer with cable) 00 lbs Reverse polarity protection of the supply voltage,excess voltage, Standard Features override and short circuit protection Life expectancy >0 Mio. load cycles 0 to 00 %FS Applications: Approvals: Electronics Catalog

20 Model Code: Series HDA 80 = submersible transducer Output Signal A = conductor, -0 ma Current Range XXXX = Pressure range 5, 0, 5, 0, 50, 00, 50, 50, 500 psi Modification Number XXX = Modification Number EPDM Seal E Other pressure ranges up to 500 psi available upon request. Contact product management for availability. HDA 80 - A - XXXX - XXX E(PSI) Circuit Connection: red + supply black 0 V Dimensions: HEX-SW.06 (7mm) ø.06 (7mm) SW 0.78 (9mm) /-NPT 0. (mm) Ventilating Tube ø.6 (9.9mm) /-8NPT Screen 0.67 (6.99mm).0 (.7mm) 0ft (.9m).97 (50mm) -877-GO HYDAC Electronics Catalog