Roto Patio S Standard hardware for Tilt&Slide windows and doors

Transcription

1 Window and Door Technology Roto Patio S Standard hardware for Tilt&Slide windows and doors Installation, maintenance and operation instructions for timber and PVC pro les

2 Imprint Copyright: September 2015 Roto Frank AG Window and Door Technology Wilhelm-Frank-Platz Leinfelden-Echterdingen Germany Phone Fax info@roto-frank.com

3 Contents General information Product liability guidelines... General advice... 7 Application diagrams for Patio 100 S... 8 Application diagrams for Patio 160 S... 9 Versions Vertical cross section timber for Patio 100 S and 160 S Vertical cross section PVC for Patio 100 S and 160 S Hardware overview Patio 100 S Basic security / RC Patio 160 S Basic security / RC Patio 160 S RC Patio 160 S 2-sashed; with opposing hardware groove Patio 160S 2-sashed; with concealed hardware groove Jigs... 3 Storage lengths of accessories Pro le-related components Pro le-related components Installation Sash pro le cross section, window-handle drilling / installation... 0 Sash... 2 Cropper / installation hardware... 2 Installation procedure for left-hand version... 3 Installation procedure for right-hand version... Installation procedure for left-hand/right-hand version... 5 Bogies up to 100 kg sash weight... 6 Bogies up to 160 kg sash weight... 8 Drill holes for Patio 160 S... 8 Frame, Installing hardware components Basic security, RC1 and RC Jigs... 5 Frame preparation Mounting the guide track Mounting the roller track Frame and sash connection Hinging the sash Aligning the sash horizontally Aligning the bogies parallel Locking cam adjustment instructions Activating the bogie safety mechanism, mounting the bogie cover Mounting the guide block Mounting the slidable guide block... 6 Mounting the buffer stop Unhinging the sash Maintenance and operating information Security Subject to change. Roto Patio S IMO_119_EN_v1 September

4 Product liability guidelines Tilt&Turn and sliding hardware for windows and balcony doors According to the de ned manufacturer s liability described in paragraph of the product liability law, the following information regarding Turn-Only and Tilt&Turn hardware for window and balcony door sashes should be observed. Non-compliance exempts the manufacturer of his liability. 1. Product information and stipulated application 1.1 Turn-Only and Tilt&Turn hardware Definition: Turn-Only and Tilt&Turn hardware as covered by this de nition is one-hand-operation Turn-Only and Tilt&Turn hardware for windows and balcony doors in building construction. This is used to enable windows and balcony-door sashes into a turning position by operating a hand-lever (handle) or into a limited tilting position in the case of the scissors (sash-stay) version. Application: Turn-Only and Tilt&Turn hardware is used on vertically installed windows and balcony-doors made of timber, PVC, aluminium or steel and their corresponding material combinations. Conventional Turn-Only and Tilt&Turn hardware as covered by this de nition, locks window and balcony door sashes or enables various ventilating positions. When closing, the gasket counter force must be overcome as a rule. 1.2 Sliding hardware Definition: Sliding hardware as covered by this de nition, is hardware for sliding sashes for balcony doors and windows that are mainly used as glazed exterior structures. In combination with the sliding sashes, xedglazing-units and/or further sashes i.e. Turn- Only sashes for cleaning purposes can be situated in a window element. Application: Sliding hardware is used on vertically installed windows and balcony door sashes made of timber, PVC, aluminium or steel, and their corresponding material combinations. Sliding hardware as covered by this de nition is equipped with a locking mechanism that fastens the sliding sash as well as rollers located on the bottom horizontal plane of the sliding sash. In addition, scissor stayarms for tilting and mechanisms to lift and/or parallel-retract the sashes can be speci ed. By means of the hardware, the sashes are locked, brought into the ventilation position and pushed to the side. Depending on the outside temperature, relative air humidity of the ambient air, as well as the application location of the sliding element, a temporary formation of condensation water on the aluminium track on the inside may occur. This is particularly promoted when the air circulation is hindered; for example due to deep reveals, curtains as well as unfavourable radiator positioning and the like. 1.3 Differing application Liability exclusion All applications differing from 1.1 are regarded as non-stipulated applications and exclude any liability on our part. 1. Advice concerning restrictions of use Opened balcony doors and window sashes, as well as window and balcony door sashes not locked or in the tilted modus, provide only a shielding function and do not meet any demands on joint impermeability, water tightness, sound reduction, heat-insulation and burglary resistance. In the case of wind and draught, the window and balcony door sashes must be closed and locked. Wind and draught is present, if a window sash or balcony-door leaf, while in one of its opening positions, can open or close on its own in an uncontrolled manner by means of either air pressure or air suction. A static opening position of window and balcony-door sashes can only be achieved by means of additional hardware. 1.5 Particular necessary agreements for extended requirements Burglar-resistant windows and balcony doors, windows and balcony doors for damp rooms and those for use in environments with aggressive, corrosive air content, require hardware adapted for the respective application and individually agreed upon performance features. The resistance against wind loads in a closed and locked state is dependent on the respective designs of windows & balcony doors. If wind loading tests need to be carried out (for example in accordance with DIN EN in particular pressure test p3), suitable hardware compilations are to be matched in relation to the respective window design and frame material, and each case individually agreed upon. Generally speaking, the hardware de ned in 1.1 ful ls the requirements for barrier-free dwellings (for example, in accordance with DIN 18025). However corresponding hardware compilations and installations for windows and balcony doors are necessary, which must be coordinated and each case individually agreed upon. 2. Misuse Misuse therefore not the stipulated product utilisation occurs in particular with hardware for windows and balcony doors as described in 1.1 and/or 1.2 in particular: If obstacles are inserted in the opening vicinity between frame and sash, thus preventing or inhibiting its proper specified use, if additional loads are put on windows or balcony-door sashes (for example if children swing on the window or balcony door sash), if window and balcony-door sashes are pressed adversatively or uncontrolled (for example by the wind) up against the window reveals, so that the hardware or the frame material or other individual window or balcony-door components are damaged or destroyed and/or if consequential damage can arise, if while closing (or sliding) someone reaches between the sash and frame, and/ or a person (or parts thereof) are in the vicinity (risk to life and limb). September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

5 3. Liability The respective entire hardware set may only consist of hardware components from Roto s NT system. In the case of non factory-approved combinations by Roto Frank AG and/or inappropriately assembled hardware, and/or the use of non-original and/or non factory-approved accessory components, no liability is accepted. For professional screw- xing, the Quality Assurance Association: Locks and Hardware s directive TBDK (Fixing load-bearing Turn-Only and Tilt&Turn hardware components) is to be adhered. (Refer to the general advice.) When using PVC or light metal pro les, the pro le manufacturer s and/or system owner s information is to be observed. The window fabricator is essentially responsible for the compliance of the speci ed system-related dimensions (for example, the gasket gap dimensions). These speci- ed system-related dimensions are to be checked regularly, in particular when using new hardware components for the rst time, and also during production as well as during the window installation process. The hardware components should in principle be designed in such a manner, that the system-related dimensions can be adjusted to the extent that they are affected by the hardware. Should there be a deviation from these dimensions that leads to a fault that has not been noted before the window installation, no liability is accepted for the additional expenses incurred.. Product performance Manufacturer s application advice.1 Maximum sash weights The listed maximum sash weights for the individual hardware versions may not be exceeded. The building component with the least permissible load-carrying capacity determines the maximum sash weight. Application diagrams and component classi cation are to be adhered to (refer to chapter Diagrams / Pro le cross sections)..2 Sash sizes The description of the application diagrams in the planning documentation, product catalogues or installation instructions depict the relationships between the permissible sash rebate widths and sash rebate heights, depending on various glass weights and/or thickness. The resulting sash dimensions or sash formats (portrait and/or landscape format) as well as the maximum sash weight may not under any circumstance be exceeded..3 Hardware combination The manufacturer s regulations that deal with the combination of hardware are obligatory (for example: the application of additional stay arms, the hardware design for burglar-resistant window sashes and balcony-door leaves etc.). 5. Product maintenance Security relevant hardware components are to be examined at least once a year for stability and wear and tear. Depending on the requirements, the xing screws are to be tightened and/or parts to be replaced. In addition to this, the following maintenance work is to be carried out at least once a year: All movable parts and all locking points of the hardware are to be lubricated and tested. Only cleaning and maintenance agents, that do not damage the corrosion protection of the hardware components, are to be used. The hardware adjustments particularly in the vicinity of the pivot rests and the scissor stays as well as replacing parts and the unhinging & hinging of the active sash are to be carried out by a specialist company. When coating for example when painting or varnishing the windows and balcony doors hardware is to be excluded from this process and is also to be protected against any impurities (paint/varnish splashes). 5.1 Preservation of the surface nish Electrolytically applied zinc coatings are not attacked in a normal room climate, if no condensation can form on the hardware or occasionally formed condensation can dry rapidly. In order to permanently preserve the hardware s surface quality and to avoid deterioration by corrosion, it is imperative to observe the following points: The hardware and/or the rebate areas are to be ventilated sufficiently in particular during the building phase so that they are not exposed either to direct wetness nor to condensation. In any case, necessary steps are to be taken to ensure that (permanent) moist ambient air cannot condense in the rebate areas. The hardware is to be kept free from deposits and soiling from building materials (building dust, plaster, cement etc.). Possible soiling from plaster, mortar or similar materials is to be removed with water before it cures. Aggressive vapours (e.g. by means of formic acid or acetic acid, ammonia, amine or ammonia compounds, aldehydes, phenols, chlorine, tannic acid etc.) in connection with even small formations of condensation can lead to fast corrosion of the hardware. For this reason, evaporation in the vicinity of the windows is to be absolutely avoided. On windows and balcony doors made of oak or other types of timber with a high concentration of (tannic-) acid, ensure that by means of a suitable window surface treatment, these content substances can not evaporate out of the timber. The hardware may not come in direct contact with untreated timber surfaces. Furthermore no acetic-acid or crosslinked acidic sealing compounds or those with the above mentioned contents may be used, since both the direct contact with the sealing compound and its vaporisation can attack the hardware s surface. Subject to change. Roto Patio S IMO_119_EN_v1 September

6 The hardware may only be cleaned with mild, ph-neutral cleaning agent in diluted form. Under no circumstances may aggressive, acidiferous cleaners or abrasive cleaning agents whose contents are listed in the above paragraph be used. Basically only zinc-plated and passivated screws are to be used for fixing the hardware components. By no means may stainless-steel screws be used, as this promotes the corrosion of zinc-plated surfaces. 6. Obligation to issue information and instructions The following documentation in particular is available in order to ful l the information and instruction duties, as well as implementing maintenance operations. This documentation is to be passed on to dealers, intermediaries, fabricators and end-users. Planning documentation Product catalogues Installation instructions Maintenance and care instructions as well as operating instructions 7. Use of related hardware The variations possible within individual hardware systems (e.g. Tilt-Only and Top- Hung hardware, or hardware that provides a circumferential ventilation-gap by parallelretracting the sash instead of, or in addition to the tilted position) are to be treated according to the corresponding valid features of product information, stipulated application, misuse, product performance, product maintenance, information & instruction obligations. This is described subsequently as product information whether in whole or in part. In order to safeguard the relevant function of windows and balcony doors: Planning engineers are obliged to request and comply with the manufacturers or authorised dealers product information. Specialised dealers are obliged to observe the product information from the manufacturer particularly valid for advertising measures and to pass this on to subsequent dealers and/or fabricators, and to point out to them that they are also obliged to pass this on to their customers. Fabricators are obliged to observe the product information and in particular, to pass on service & maintenance instructions as well as operating manuals to the builders and end-users. 6 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

7 General advice 12 mm clearance mm overlap width 9/13 mm hardware axis 15 mm min. overlap height 18 mm travel with handle turned 90 Hardware functional safety In order to warrant continuous hardware functional safety, the following should be observed: 1. Professional installation of the hardware components in accordance with these installation instructions. 2. Compliance with the maintenance and operation instructions. 3. Professional installation of the elements throughout the window installation process.. Display user information visibly on the installed window unit and pass on the operating instructions to users. 5. The entire hardware may consist of only original Roto system components. The use of non-roto components excludes any liability on our part. 6. Roller tracks and guide tracks are to be cleaned regularly from dust and dirt, so that the rollers smooth operation is maintained. Product liability regulations The window handle is to be xed with M5 x... countersunk screws and 3.9 x... for ush-encased gearboxes. When xing the hardware components, corrosion protected hardwareadapted 3.5 x....8 x... fenestration screws are to be used. (Adhere the advice on the following pages.) The window fabricator must ensure adequate xing of the hardware components, consulting the screw manufacturer if necessary. The screwextraction values in accordance with the Quality Assurance Association: Locks and Hardware s directive TBDK (Fixing load-bearing Turn-Only and Tilt&Turn hardware components) shall be adhered. The glazing spacer-block regulations for the glazing method are to be adhered. If a Turn-Only sash is installed instead of a xed unit, the maximum permitted application ranges of the Roto NT hardware system apply. Product liability Liability exclusion The hardware manufacturer is not liable for malfunctions or damage to the hardware and to the windows or balcony doors equipped with the hardware, if any such malfunctions or damage has been caused by inadequate tendering procedures or failure to adhere to the installation instructions and application drawings. Subject to change. Roto Patio S IMO_119_EN_v1 September

8 Application diagrams for Patio 100 S Application diagram Patio 100 S Application range Sash rebate width (SRW) mm Sash rebate height (SRH) mm Sash weight...max. 100 kg Glass weight...max. 60 kg / m 2 1 mm / m 2 glass thickness = 2.5 kg SRH : SRW = max. 2.5 : 1 Sash rebate height (SRH) in mm = Impermissible application range 30 kg/m 2 0 kg/m 2 50 kg/m 2 60 kg/m Sash rebate width (SRW) in mm 8 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

9 Application diagrams for Patio 160 S Application diagram Patio 160 S Application range Sash rebate width (SRW) mm Sash rebate height (SRH) mm Sash weight... max. 160 kg Glass weight...max. 60 kg / m 2 1 mm / m 2 glass thickness = 2.5 kg SRH : SRW = max. 2.5 : Sash rebate height (SRH) in mm = Impermissible application range 30 kg/m 2 0 kg/m 2 50 kg/m 2 60 kg/m 2 Sash rebate width (SRW) in mm Subject to change. Roto Patio S IMO_119_EN_v1 September

10 Versions Diagram A L L Diagram A 1 sliding sash (L or R) 1 xed glazing Diagram A 1 sliding sash (L or R) 1 Turn-Only sash Diagram B R Diagram B 1 sliding sash (L or R) Inside frame ush with the wall Diagram C R L R L Diagram C 2 sliding sashes (L or R) with/without centre post 2 Turn-Only sashes (alternatively xed glazing) Diagram C 2 sliding sashes (L and R) with xed centre post 2 Turn-Only sashes (alternatively xed glazing) Diagram D R Diagram D 1 sliding sash (L or R) with/without centre post, slidable guide block required (page 37). 1 Turn-Only sash Diagram G R R Diagram G 1 sliding sash (L or R) 2 xed glazings Diagram G 1 sliding sash (L or R) 2 Turn-Only sashes Diagram K L R Diagram K 2 sliding sashes (L and R) 1 xed glazing 10 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

11 L Diagram A Sliding sash / Fixed glazing Sliding sash left Fixed glazing 15 backset L Diagram A Sliding sash / Turn-Only sash (with xed centre post) Sliding sash left Turn-Only sash 15 backset 15 backset R L Diagram C Sliding sash (with xed centre post) / Turn-Only sash (alternatively xed glazing) Turn-Only sash Sliding sash right Sliding sash left Turn-Only sash 15 backset 15 backset 15 backset 15 backset R L Diagram C Sliding sash (without xed centre post) / Turn-Only sash (alternatively xed glazing) Turn-Only sash Sliding sash right Sliding sash left Turn-Only sash 15 backset 5 backset 15 backset 15 backset L Diagram A Sliding sash / Fixed glazing Sliding sash left Fixed glazing 15 backset L Diagram A Sliding sash / Turn-Only sash (with xed centre post) Sliding sash left Turn-Only sash 15 backset 15 backset R L Diagram C Sliding sash (with xed centre post) / Turn-Only sash (alternatively xed glazing) Turn-Only sash Sliding sash right Sliding sash left Turn-Only sash 15 backset 15 backset 15 backset 15 backset R L Diagram C Sliding sash (without centre post) / Turn-Only sash (alternatively xed glazing) Turn-Only sash Sliding sash right Sliding sash left Turn-Only sash 15 backset 5 backset 15 backset 15 backset Subject to change. Roto Patio S IMO_119_EN_v1 September

12 Vertical cross section timber for Patio 100 S and 160 S Patio 160 S SRH Patio 160 S Patio 100 S Patio 100 S max. TSFF Retracting distance 125 min. overlap height = 15 Underlay the roller track over the entire length on site in order to distribute the load. At a coverage dimension of 6 mm All dimensions stated in mm. 12 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

13 Vertical cross section PVC for Patio 100 S and 160 S Patio 160 S Patio 160 S SRH Patio 100 S 12 Patio 100 S max. TSFF Retracting distance 125 min. overlap height = Underlay the roller track over the entire length on site in order to distribute the load. At a coverage dimension of 8 mm All dimensions stated in mm. Subject to change. Roto Patio S IMO_119_EN_v1 September

14 Note: The hardware combinations listed in the following are only examples. Please see the NT product range for additional espagnolettes and espagnolette extensions. 1 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

15 Patio 100 S Basic security / RC1 Hardware overview 7 1 for RC for RC Depicted: Left-hand version (DIN 12519) 6 Subject to change. Roto Patio S IMO_119_EN_v1 September

16 Patio 100 S Basic security / RC1 Parts list Basic carton Patio 100S / 160S NT Patio S NT Basic carton L Content: leading bogie trailing bogie Patio S NT Basic carton R Content: leading bogie (not dep.) trailing bogie (not dep.) Centre lock component 3 Centre lock component, vertical SRH / mm Length / mm Handle height / mm Cam Material no E E 1V E 1V E 1V E 1V E 1V E 1V E 1V E 1V Centre lock component, bottom horizontal SRW / mm Length / mm Handle height / mm Cam Material no E E E Centre lock component, top horizontal SRW / mm Length / mm Handle height / mm Cam Material no E E E Track set for sash and frame incl. misc. small components pack R 01.1 Silver SRW / mm Frame external width (FEW) / mm Material no R 05.3 Medium bronze R 05. Dark bronze R 07.2 Traf c white R 07.3 Cream white Content of the track set: 6 1 roller track 7 1 guide track 8 1 cover profile 9 1 PVC cover profile 10 1 connecting rod Misc. small components pack: 13 2 cover caps for Patio 100 S Misc. small components pack: 1 2 end caps for guide track 15 1 guide block 16 1 buffer stop, bottom 17 1 buffer stop, top 19 1 rubber buffer stop 20 1 cover support bracket Misc. small components pack: 11 1 stay-connecting profile 12 1 scissors-slider 18 2 end caps for stay-connecting profile 16 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

17 Espagnolette 25 T&T espagnolette, fixed handle height, 15 mm backset SRH / mm Length / mm Handle height / mm Cam Material no E E E E E E E E E E T&T espagnolette, centred/variable handle height, 15 mm backset SRH / mm Length / mm Handle height / mm Cam Material no E E E E E Corner drive 27 Corner drive, T&T 1V Corner drive RC1 and RC2 1V Corner drive Corner drive as alternative to 29 1V Roto Line handle, with Roto logo, refer to CTL 1 EN 60 Guide striker refer to page Striker refer to page Security striker refer to page 36 Subject to change. Roto Patio S IMO_119_EN_v1 September

18 18 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

19 Patio 160 S Basic security / RC1 Hardware overview for RC for RC Depicted: Left-hand version (DIN 12519) 6 Subject to change. Roto Patio S IMO_119_EN_v1 September

20 Patio 160 S Basic security / RC1 Parts list Basic carton Patio 100 S / 160 S NT Patio S NT Basic carton L Content: leading bogie trailing bogie Patio S NT Basic carton R Content: leading bogie (not dep.) trailing bogie (not dep.) Centre lock component 3 Centre lock component, vertical SRH / mm Length / mm Handle height / mm Cam Material no E E 1V E 1V E 1V E 1V E 1V E 1V E 1V E 1V E 1V Espagnolette extension 200 1E E 1V Espagnolette extension 00 1E Centre lock component, bottom horizontal SRW / mm Length / mm Handle height / mm Cam Material no E E E E Centre lock component, top horizontal SRW / mm Length / mm Handle height / mm Cam Material no E E E E Track set for sash and frame incl. misc. small components pack R 01.1 Silver SRW / mm Frame external width (FEW) / mm Material no R 05.3 Medium bronze R 05. Dark bronze R 07.2 Traf c white R 07.3 Cream white Content of the track set: 6 1 roller track 7 1 guide track 8 1 cover profile 9 1 PVC cover profile 10 1 connecting rod Misc. small components pack: 13 2 cover caps for Patio 100 S (not relevant for this version) Misc. small components pack: 1 2 end caps for guide track 15 1 guide block 16 1 buffer stop, bottom 17 1 buffer stop, top 19 1 rubber buffer stop 20 1 cover support bracket Misc. small components pack: 11 1 stay-connecting profile 12 1 scissors-slider 18 2 end caps for stay-connecting profile From SRW 150 mm misc. small components pack: 21 1 support-block 22 1 cover support bracket 20 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

21 Supplemental set for Patio 160 S Description Material no. R01.1 Silver R05.3 Medium bronze R05. Dark bronze R07.2 Traffic white R07.3 Cream white Content: 23 2 cover caps for Patio 160 S 2 2 reinforcement brackets Espagnolette 25 T&T espagnolette, xed handle height, 15 mm backset SRH / mm Length / mm Handle height / mm Cam Material no E E E E E E E E E E E Espagnolette extension E E Espagnolette extension 00 1 E T&T espagnolette, centred/variable handle height 15 mm backset SRH / mm Length / mm Handle height / mm Cam Material no E E E E E Corner drive 27 Corner drive, T&T 1V Corner drive RC1 and RC2 1V Corner drive Corner drive as alternative to 29 1V Roto Line handle, with Roto logo, refer to CTL 1 EN 60 Guide striker refer to page Striker refer to page Security striker refer to page 36 Subject to change. Roto Patio S IMO_119_EN_v1 September

22 22 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

23 Patio 160 S RC2 Hardware overview Depicted: Left-hand version (DIN 12519) 6 Subject to change. Roto Patio S IMO_119_EN_v1 September

24 Patio 160 S RC2 Parts list Basic carton Patio 100 S / 160 S NT Patio S NT Basic carton L Content: leading bogie trailing bogie Patio S NT Basic carton R Content: leading bogie (not dep.) trailing bogie (not dep.) Centre lock component 3 Centre lock component, security vertical SRH / mm Length / mm Handle height / mm Cam Material no V V V V V V V V V V Espagnolette extension V V Espagnolette extension 00 1 V Centre lock component, security, bottom horizontal SRW / mm Length / mm Handle height / mm Cam Material no V V V V Centre lock component, security, top horizontal SRW / mm Length / mm Handle height / mm Cam Material no V V V V Track set for sash and frame incl. misc. small components pack R 01.1 Silver SRW / mm Frame external width (FEW) / mm Material no R 05.3 Medium bronze R 05. Dark bronze R 07.2 Traf c white R 07.3 Cream white Content of the track set: 6 1 roller track 7 1 guide track 8 1 cover profile 9 1 PVC cover profile 10 1 connecting rod Misc. small components pack: 13 2 cover caps for Patio 100 S (not relevant for this version) Misc. small components pack: 1 2 end caps for guide track 15 1 guide block 16 1 buffer stop, bottom 17 1 buffer stop, top 19 1 rubber buffer stop 20 1 cover support bracket Misc. small components pack: 11 1 stay-connecting profile 12 1 scissors-slider 18 2 end caps for stay-connecting profile From SRW 150 mm misc. small components pack: 21 1 support-block 22 1 cover support bracket 2 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

25 Supplemental set for Patio 160 S Description Material no. R01.1 Silver R05.3 Medium bronze R05. Dark bronze R07.2 Traffic white R07.3 Cream white Content: 23 2 cover caps for Patio 160 S 2 2 reinforcement brackets Espagnolette 25 Security T&T espagnolette, xed handle height, 15 mm backset SRH / mm Length / mm Handle height / mm Cam Material no V V V V V V V V V V V Espagnolette extension V V Espagnolette extension 00 1 V Corner drive 27 Corner drive, T&T 1V Corner drive RC1 and RC2 1V Corner drive Corner drive as alternative to 29 1V Roto Line handle with Roto logo lockable, 100 Nm refer to CTL 1 EN 52 Drilling protection Guide striker refer to page Security striker refer to page 36 Subject to change. Roto Patio S IMO_119_EN_v1 September

26 26 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

27 Patio 160 S 2-sashed; with opposing hardware groove Hardware overview Profile cross section Backset 5 Striker mounted on opposing espagnolette 15 Backset Subject to change. Roto Patio S IMO_119_EN_v1 September

28 Patio 160 S 2-sashed; with opposing hardware groove Parts list Basic carton Patio 100 S / 160 S NT, 1 piece per sash Patio S NT Basic carton L Content: leading bogie trailing bogie Patio S NT Basic carton R Content: leading bogie trailing bogie (not dep.) Centre lock component 3 Centre lock component, vertical SRH / mm Length / mm Handle height / mm Cam Material no E E 1V E 1V E 1V E 1V E 1V E 1V E 1V E 1V E 1V Espagnolette extension 200 1E E 1V Espagnolette extension 00 1E Centre lock component, bottom horizontal SRW / mm Length / mm Handle height / mm Cam Material no E E E E Centre lock component, top horizontal SRW / mm Length / mm Handle height / mm Cam Material no E E E E Track set each sash 1 piece per sash and frame incl. misc. small components pack R 01.1 Silver SRW / mm Frame external width (FEW) / mm Material no R 05.3 Medium bronze R 05. Dark bronze R 07.2 Traf c white R 07.3 Cream white Content of the track set: 6 1 roller track 7 1 guide track 8 1 cover profile 9 1 PVC cover profile 10 1 connecting rod Misc. small components pack: 13 Cover cap for Patio 100 S (not relevant for this version) Misc. small components pack: 1 2 end caps for guide track 15 1 guide block 16 1 buffer stop, bottom 17 1 buffer stop, top 19 1 rubber buffer stop 20 1 cover support bracket Misc. small components pack: 11 1 stay-connecting profile 12 1 scissors-slider 18 2 end caps for stay-connecting profile From SRW 150 mm misc. small components pack: 21 1 support-block 22 1 cover support bracket *) The guide track and the roller track must not be painted. 28 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

29 Supplemental set for Patio 160 S, 1 piece per sash Description Material no. R01.1 Silver R05.3 Medium bronze R05. Dark bronze R07.2 Traffic white R07.3 Cream white Content: 23 2 cover caps for Patio 160 S 2 2 reinforcement brackets Espagnolette 25 T&T espagnolette, centred/variable handle height 15 mm backset SRH / mm Length / mm Handle height / mm Cam Material no E E E E E T&T espagnolette, centred/variable handle height 5 mm backset SRH / mm Length / mm Handle height / mm Cam Material no St St St St St St. = Striker T&T espagnolette, centred/variable handle height 50 mm backset SRH / mm Length / mm Handle height / mm Cam Material no St St St St St St. = Striker Corner drive 27 Corner drive, T&T 1V Corner drive RC1 and RC2 1V Corner drive Corner drive as alternative to 29 1V Roto Line handle, with Roto logo, refer to CTL 1 EN 60 Guide striker refer to page Striker refer to page Security striker refer to page 36 St. = Striker Subject to change. Roto Patio S IMO_119_EN_v1 September

30 30 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

31 Patio 160 S 2-sashed; with concealed hardware groove Hardware overview Profile cross section Backset Backset Striker mounted on floating mullion profile Subject to change. Roto Patio S IMO_119_EN_v1 September

32 Patio 160 S 2-sashed; with concealed hardware groove Parts list Basic carton Patio 100 S / 160 S NT, 1 piece per sash Patio S NT Basic carton L Content: leading bogie trailing bogie Patio S NT Basic carton R Content: leading bogie trailing bogie (not dep.) Centre lock component 3 Centre lock component, vertical SRH / mm Length / mm Handle height / mm Cam Material no E E 1V E 1V E 1V E 1V E 1V E 1V E 1V E 1V E 1V Espagnolette extension 200 1E E 1V Espagnolette extension 00 1E Centre lock component, bottom horizontal SRW / mm Length / mm Handle height / mm Cam Material no E E E E Centre lock component, top horizontal SRW / mm Length / mm Handle height / mm Cam Material no E E E E Track set each sash 1 piece per sash and frame incl. misc. small components pack R 01.1 Silver SRW / mm Frame external width (FEW) / mm Material no R 05.3 Medium bronze R 05. Dark bronze R 07.2 Traf c white R 07.3 Cream white Content of the track set: 6 1 roller track 7 1 guide track 8 1 cover profile 9 1 PVC cover profile 10 1 connecting rod Misc. small components pack: 13 Cover cap for Patio 100 S (not relevant for this version) Misc. small components pack: 1 2 end caps for guide track 15 1 guide block 16 1 buffer stop, bottom 17 1 buffer stop, top 19 1 rubber buffer stop 20 1 cover support bracket Misc. small components pack: 11 1 stay-connecting profile 12 1 scissors-slider 18 2 end caps for stay-connecting profile From SRW 150 mm misc. small components pack: 21 1 support-block 22 1 cover support bracket 32 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

33 Supplemental set for Patio 160 S, 1 piece per sash Description Material no. R01.1 Silver R05.3 Medium bronze R05. Dark bronze R07.2 Traffic white R07.3 Cream white Content: 23 2 cover caps for Patio 160 S 2 2 reinforcement brackets Espagnolette 25 T&T espagnolette, xed handle height, 15 mm backset SRH / mm Length / mm Handle height / mm Cam Material no E E E E E E E E E E E Espagnolette extension E E Espagnolette extension 00 1 E T&T espagnolette, xed handle height, 15 mm backset, without locking cam SRH / mm Length / mm Handle height / mm Cam Material no Espagnolette extension Espagnolette extension Corner drive 27 Corner drive, T&T 1V Corner drive RC1 and RC2 1V Corner drive Corner drive as alternative to 29 1V Roto Line handle, with Roto logo, refer to CTL 1 EN 60 Guide striker refer to page Striker refer to page Security striker refer to page 36 Subject to change. Roto Patio S IMO_119_EN_v1 September

34 Jigs Slider-release device Jig for roller track and guide track Drilling aid for roller track and guide track Drilling jig for bogie Jig for guide block Torx key; T0 hexalobular socket Torx key; T25 hexalobular socket September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

35 Positioning jigs, horizontal for Patio S SRW/mm Material no L R L R L R L R L R Positioning jigs, vertical, xed handle height SRH/mm Material no Positioning jigs, vertical, centred/variable handle height SRH/mm Material no Drilling jig for slidable guide block Subject to change. Roto Patio S IMO_119_EN_v1 September

36 Storage lengths of accessories Description Colour Comment Length in mm Material no. Tracks 6 Roller track Non-treated R 01.1 Silver R 05.3 Medium bronze R 05. Dark bronze Guide track R 01.1 Silver Connecting rod Stay-connecting profile 13 Non-treated R01.1 Silver R 05.3 Medium bronze R 05. Dark bronze R 07.2 Traffic white R 07.3 Cream white a Stay-connecting profile 20 * R 01.1 Silver R 05.3 Medium bronze R 05. Dark bronze R 07.2 Traffic white R 07.3 Cream white End caps End cap for stay-connecting profile 13 DIN L R 01.1 Silver DIN R DIN L R 05.3 Medium bronze DIN R DIN L R 05. Dark bronze DIN R DIN L R 07.2 Traffic white DIN R DIN L R 07.3 Cream white DIN R End cap for stay-connecting profile 20 DIN L R 01.1 Silver DIN R R DIN L R 05.3 Medium bronze DIN R R DIN L R 05. Dark bronze DIN R R DIN L R 07.2 Traffic white DIN R R DIN L R 07.3 Cream white DIN R R End cap *Use the stay-connecting profile 20 for inclines or large radii. 36 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

37 Scissor stays 12 Scissors-slider SRW 600 mm 900 mm SRW 901 mm 1200 mm SRW 1201 mm 1650 mm Cover profiles 8 Aluminium cover profile Non-treated R 01.1 Silver R 05.3 Medium bronze R 05. Dark bronze R 07.2 Traffic white R 07.3 Cream white PVC cover profile Grey Consistent with R 01.1 (silver) Medium brown Consistent with R 05.3 (medium bronze) Black Consistent with R 05. (dark bronze) White Consistent with R 07.2 (traffic white) R 07.3 Cream white Cover caps for reinforcement brackets 160 S 23 Cover caps for reinforcement bracket L/R R 01.1 Silver R 05.3 Medium bronze R 05. Dark bronze R 07.2 Traffic white R 07.3 Cream white Description Colour Comment Length in mm Material no. Window contact MVS / MTS components MVS contact element (VdS grade B) 6 m cable MVS contact element (VdS grade C) 6 m cable MVS contact element (VdS grade B) 10 m cable MVS contact element (VdS grade C) 10 m cable Packer 0.5 mm high, stackable, for flat profiles MVS installation set Retrofittable on horizontal centre lock component MVS corner drive 1 V cam and 1 magnet MTS contact element 2) With 6 m cable, white, with installation instructions With 10 m cable, white, with installation instructions With cable in special length Upon request Packers Installation base, PVC RAL 7035, to be ordered separately (1 packer per contact element). ( p. 0) Installation base, timber RAL 7035, 0.5 mm high, for even profiles Guide blocks, slidable (jig required) Guide block, slidable R 01.1 Silver R 05.3 Medium bronze R 05. Dark bronze Cover caps for 100 S NT (for cover profile) 13 Cover cap for 100 S NT L/R Black R 07.2 White R 07.3 Cream white Subject to change. Roto Patio S IMO_119_EN_v1 September

38 Profile-related components ADVICE! Treat uncoated parts as follows: Never coat roller tracks and guide tracks. Only anodised surfaces may be coated. Stay-connecting profiles and cover profiles may only be powder-coated or wet painted. Procedural instructions for PVC cover caps: Pre-treat with plasma in a vacuum chamber. Clean with ionised air. Paint with bi-component acrylic varnish. Oven drying at 70 C 38 September 2015 IMO_119_EN_v1 Roto Patio S Subject to change.

39 Profile-related components Profile system Guide striker 60 Striker, standard 61 Security striker, zinc 62 Security striker, steel 62 Striker ordering / marking Order right-handed security strikers for left-handed version (in accordance with DIN 12519). Order left-handed security strikers for right-handed version (in accordance with DIN 12519). Actual Alphacan System Class Aluplast Ideal 2000/ Aluplast Ideal 000/5000/ Brügmann AD/MD Deceuninck Mondial VK/Klassiek Dimex Contur 7.0/Elegance Dimex Komfort Finstral R L Finstral R L Gealan 3000/7000/ Inoutic AD13/MD Inoutic Prestige AD Inoutic Prestige MD KBE 70 AD R L KBE 70 MD Kömmerling EuroFutur Classic (w/o base) Kömmerling Eurodur Mpf Kömmerling Eurodur 3S Kömmerling Kömmerling Gold LB PAD Rehau (730) Brillant Design Rehau Geneo Roplasto K Salamander 2D/3D R L Salamander SL R L Schüco Corona AD Schüco Corona MD Schüco Corona CT70AD/MD; Si82/MD Trocal Confort Trocal InnoNova 70 AD/MD Plus (w/o base) Trocal InnoNova R L Trocal R L Veka Alphaline Veka Softline 70 AD/MD Veka Topline MD/AD Wymar Without supporting-pins Timber 18 mm rebate R L R L Timber 20 mm rebate R L R L Timber 2 mm rebate R L Timber 7/8 mm groove, 18 mm rebate depth R L R L Timber 7/8 mm groove, 20 mm rebate depth R L R L Further profile-related components are available upon request. Subject to change. Roto Patio S IMO_119_EN_v1 September